Ryobi RY405011BTL Le manuel du propriétaire

Marque: Ryobi

Modèle: RY405011BTL

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

Ce manuel convient également à

RY405110

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

20 in. 40 VOLT BRUSHLESS CHAINSAW

SCIE À CHAÎNE SANS BALAI DE 40 V DE 50,8 cm (20 po)

MOTOSIERRA SIN ESCOBILLAS DE 50,8 cm (20 pulg.), 40 V

RY405011

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

TABLE OF CONTENTS

 General Power Tool Safety Rules .... 2-3

 Chainsaw Safety Warnings ............. 3-6

 Symbols .......................................... 6-7

 Glossary of Terms ...............................8

 Features ..............................................9

 Assembly ...................................... 9-10

 Operation .................................... 10-15

 Maintenance ............................... 15-18

 Bar and Chain Combinations ............ 18

 Troubleshooting ................................19

 Parts Ordering/Service ........ Back Page

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

TABLE DES MATIÈRES

 Avertissements règles de sécurité

relatives aux outils électriques ........ 2-3

 Avertissements de sécurité

relatifs au scie à chaîne ................... 3-6

 Symboles ........................................ 7-8

 Glossaire .............................................9

 Caractéristiques ................................10

 Assemblage ................................ 10-11

 Utilisation .................................... 11-16

 Entretien ...................................... 16-19

 Combinaisons de guide et chaîne ....20

 Dépannage ........................................ 20

 Commande de pièces/

réparation .......................... Páge arrière

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe leer

y comprender el manual del operador

antes de usar este producto.

ÍNDICE DE CONTENIDO

 Advertencias de seguridad

para herramientas eléctricas ........... 2-3

 Advertencias de seguridad

de la motosierra .............................. 4-7

 Símbolos ......................................... 7-8

 Glosario de términos ........................... 9

 Características ..................................10

 Armado ....................................... 10-11

 Funcionamiento .......................... 11-16

 Mantenimiento ............................ 16-20

 Combinaciones de barra y cadena ...20

 Correción de problemas ...................21

 Pedidos de piezas/

servicio ........................... Pág. posterior

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

Fig. 1

See this fold-out section for all of the ﬁgures referenced

in the operator’s manual.

Consulter l’encart à volets aﬁn d’examiner toutes les ﬁgures

mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas las ﬁguras a

las que se hace referencia en el manual del operador.

A - Battery port (port du bloc-piles, puerto de batería)

B - Switch trigger (gâchette de commutateur, gatillo interruptor)

C - Rear handle (poignée arrière, mango trasero)

D - Lock-out button (bouton de verrouillage, botón de bloqueo)

E - Front handle (poignée avant,mango delantero)

F - Bar mounting nuts (écrou de montage du guide tuerca de montaje de la

barra)

G - Chain tensioning screw (vis de tension de la chaîne, tornillo tensor de

la cadena)

H - Hand guard/chain brake (Protection de poignée avant / frein de chaîne,

protección delantera de la mano/freno de la cadena

I - Chain (chaîne, cadena)

J - Scabbard (fourreau, funda)

K - Guide bar (guide de chaîne, barra guía)

L - Combination wrench (clé mixte, llave de combinación)

M - Keyhole (trou de serrure, cerradura)

N - Spiked bumper (pare-chocs à pointes, protección en punta)

O - Oil cap (bouchon d’huile, tapa de aceite)

P - Translucent oil tank (réservoir transparent d’huile, tanque translúcido

de aceite)

A - Lock-out button (bouton de verrouillage,

botón de bloqueo)

B - Switch trigger (gâchette de commutateur,

gatillo del interruptor)

Fig. 5

Fig. 2

Fig. 3

Fig. 12

Fig. 13

Fig. 7

ROTATIONAL KICKBACK

REBOND ROTATIF

CONTRAGOLPE ROTATORIO

KICKBACK DANGER ZONE

ZONE DE DANGER DE REBOND

ZONA DE PELIGRO DE CONTRAGOLPE

PUSH

POUSSÉE

EMPUJÓN

Fig. 4

A - Battery pack (bloc-piles, paquete de

baterías)

B - Battery port (logement de piles, receptáculo

de las baterías)

C - Latch (loquet, pestillo)

A - Chain oil tank cap (capuchon du réservoir

d’huile de chaîne, tapa del tanque del aceite

de la cadena )

CHAIN LINE

LIGNE DE CHAÎNE

PLANO DE LA CADENA

CORRECT

CORRECTO

Fig. 8

Fig. 9

Fig. 10

Fig. 11

INCORRECT

INCORRECTE

INCORRECTO

PULL

TIRAGE

TIRÓN

Fig. 6

RUN POSITION

POSITION DE MARCHE

POSICIÓN DE

FUNCIONAMIENTO

BRAKE POSITION

FREIN ENGAGÉ

POSICIÓN DE FRENADO

iii

HINGE 2 in. OR 1/10 DIA

CHARNIÈRE, 51 mm (2 po) OU 1/10 ÈME DU DIAMÈTRE

BISAGRA 51 mm (2 pulg.) Ó 1/10 DEL DIÁM.

NOTCH – APPROX. 1/3

DIAMETER OF TRUNK

SIFFLET - ENVIRON 1/3

DU DIAMÈTRE DU TRONC

MUESCA - APROX. 1/3

DEL DIÁMETRO DEL

TRONCO

BACK CUT 2 in.

ENTAILLE ARRIÈRE

DE 51 mm [2 po]

CORTE TRASERO 51

mm (2 pulg.)

45°

RETREAT PATH

Fig. 16

Fig. 17

Fig. 20

Fig. 21

KICKBACK

REBOND

CONTRAGOLPE

A - Chain line (ligne de chaîne, plano de la cadena)

B - Straight arm position (bras tendu, posición con el brazo recto)

Fig. 14

Fig. 15

A - Back cut (entaille d’abattage, corte trasero)

B - Notch (encoche, muesca)

C - Hinge charnière, bisagra)

A - Wedge (coin, cuña)

Fig. 18

Fig. 19

A - Planned line of fall (ligne de chute prévue,

Línea de caída planificada)

B - Straight arm position (chemin

d’échappement, trayectoria de retirada)

Fig. 25

Fig. 26

A - Overbucking (coupe par le dessus, tronzado

por arriba)

B - Underbucking (coupe par le dessous,

tronzado por abajo)

A - Chain tensioning screw (vis de tension

de la chaîne, tornillo tensor de la cadena)

B - Bar mounting nuts (écrou de montage du

guide tuerca de montaje de la barra)

A - Bar stud (goujon du guide, perno de montaje

de la barra)

B - Chain tension pin hole (orifice de broche de

tension de chaîne, pasador de tensado de la

cadena)

C - Adjusting pin (broche de réglage de tension

de chaîne,pasador de ajuste)

D - Chain cover (carter de la chaîne, tapa de la

cadena)

E - Bar mounting nuts (écrou de montage du

guide tuerca de montaje de la barra)

A - Cutters (dents, dientes de corte)

B - Chain rotation (rotation de la chaîne, avance

de la cadena)

C - Chain drive links (maillons d’entraînement,

eslabones de impulsión de la cadena)

A - Bar groove (rainure du guide, ranura de la

barra

B - Chain drive links (maillons d’entraînement,

eslabones de impulsión de la cadena)

A - Load (charge, carga)

B - Second cut (deuxième coupe, segundo

corte)

C - First cut - 1/3 diameter (première coupe 1/3

du diamètre, primer corte 1/3 del diámetro)

D - Finishing cut (coupe de finition, corte final)

A - Springpole (fouet, pértiga)

CUT LIMBS ONE AT A TIME AND LEAVE SUPPORT

LIMBS UNDER TREE UNTIL LOG IS CUT

COUPER LES BRANCHES UNE À UNE ET LAISSER

CELLES SOUTENANT LE TRONC JUSQU’À CE QU

CELUI-CI SOIT DÉBITÉ

CORTE UNA RAMA A LA VEZ Y DEJE RAMAS DE

SOPORTE BAJO EL ÁRBOL HASTA QUE ESTÉ

CORTADO EL TRONCO

123

Fig. 23

Fig. 24

Fig. 27

Fig. 31

Fig. 29

Fig. 30

A - Mounting surface (barre de leur support,

superficie de montaje)

B - Chain (chaîne, cadena)

C - Bar (barre,barra)

D - Chain cover (carter de la chaîne, tapa de la

cadena)

E - Bar mounting nuts (écrou de montage du

guide tuerca de montaje de la barra)

A - Load (charge, carga)

B - 1st cut - 1/3 diameter (1ère coupe 1/3 diam,

primer corte, 1/3 del diám.)

C - Finishing cut (coupe de finition, corte final)

Fig. 22 LOG SUPPORTED AT ONE END:

BILLE SOUTENUE À UNE EXTRÉMITÉ :

TRONCO APOYADO POR UN EXTREMO :

LOG SUPPORTED AT BOTH ENDS:

BILLE SOUTENUE AUX DEUX EXTRÉMITÉS :

TRONCO APOYADO POR AMBOS EXTREMOS :

Fig. 28

A - Drive sprocket (pignon d’entraînement, Rueda dentada de impulsión)

B - Check for wear or damage (s’assurer de l’absence d’usure ou de

dommages, revise para ver si hay desgaste o daños)

Fig. 39

Fig. 36

Fig. 35

Fig. 34 Fig. 38

RAKER CLEARANCE .025 IN.

JEU DU LIMITEUR 0,6 MM (0,025 PO)

ESPACIO LIBRE DE LOS DIENTES LIMPIADORES 0,025 MM (0,6 PULG.)

APPROX. .050 in.

≈ 1,25 mm (0,050 po)

≈ 1,25 mm (0,050 pulg.)

≈ 0.050 in.

≈ 1,27 mm (0,050 po)

≈ 1,27 mm (0,050 pulg.)

A - Top plate (plaque supérieure, placa superior)

B - Cutting Corner (coupe de coin, esquina de corte)

C - Side plate (plaque latérale, placa lateral)

D - Depth gauge (limiteur de profondeur, calibre de profundidad)

E - Toe (sabot, puntera)

F - Gullet (creux, garganta)

G - Heel (talon, talón)

H - Rivet hole (trou de rivet, orificio del remache)

A - Flats on tie straps (parties plates sur les liens de traverse, partes planas

de los amarres)

Fig. 37

A - Chain tensioning screw (vis de tension de la chaîne, tornillo tensor de

la cadena)

B - Bar mounting nuts (écrou de montage du guide tuerca de montaje de la

barra)

Fig. 32 LIFT THE TIP OF THE GUIDE BAR UP TO CHECK FOR SAG

RELEVER L’EXTRÉMITÉ DU GUIDE POUR VÉRIFIER LE MOU

LEVANTE LA PUNTA DE LA BARRA GUÍA PARA REVISAR LA HOLGURA

DE LA CADENA

Fig. 33

INCORRECT SIDE PLATE FILING ANGLE

ANGLE D’AFFÛTAGE DE LA PLAQUE LATÉRALE

INCORRECT

ÁNGULO INCORRECTO DE LIMADURA DE LA

PLACA LATERAL

BACKWARD SLOPE

ANGLE ARRIÈRE

PENDIENTE HACIA ATRÁS

HOOK

CROCHET

GANCHO

80°

CORRECT SIDE PLATE

FILING ANGLE

ANGLE D’AFFÛTAGE DE

LA PLAQUE LATÉRALE

CORRECT

ÁNGULO CORRECTO DE

LIMADURA DE LA PLACA

LATERAL

RESTORE ORIGINAL SHAPE BY

ROUNDING THE FRONT

RENDRE LA FORME D’ORIGINE EN

ARRONDISSANT L’AVANT

RESTABLEZCA LA FORMA

ORIGINAL REDONDEANDO LA

PARTE FRONTAL

Fig. 46

Fig. 42

Fig. 43

Fig. 44

Fig. 45

A - Lubricating hole (trou de lubrification, orificio de lubricación)

A - Scabbard (fourreau, funda)

A - Depth gauge jointer (coupleur de limiteur de profondeur, igualador de

calibres de profundidad)

B - Flate file (lime plate, lima plana)

INCORRECT TOP PLATE FILING ANGLE

ANGLE D’AFFÛTAGE DE LA PLAQUE

SUPÉRIEURE INCORRECT

ÁNGULO INCORRECTO DE LIMADURA DE

LA PLACA SUPERIOR

MORE THAN 30°

PLUS DE 30°

MÁS DE 30°

LESS THAN 30°

MOINS DE 30°

MENOS DE 30°

30°

CORRECT TOP PLATE FILING

ANGLE

ANGLE D’AFFÛTAGE DE

LA PLAQUE SUPÉRIEURE

CORRECT

ÁNGULO CORRECTO DE

LIMADURA DE LA PLACA

SUPERIOR

Fig. 41

Fig. 40

A - Left hand cutters (dents de droite, dientes de corte izquierdos)

B - Right hand cutters (dents de gauche, dientes de corte derechos)

2 - English

GENERAL POWER TOOL SAFETY RULES

WARNING:

Read all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to

follow all instructions listed below may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

WORK AREA SAFETY

 Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

 Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

 Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

 Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

 Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body

is earthed or grounded.

 Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

 Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

 When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suitable

for outdoor use reduces the risk of electric shock.

 If operating a power tool in a damp location is un-

avoidable, use a ground fault circuit interrupter (GFCI)

protected supply. Use of a GFCI reduces the risk of

electric shock.

PERSONAL SAFETY

 Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use

a power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inatten-

tion while operating power tools may result in serious

personal injury.

 Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

 Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites

accidents.

 Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

 Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

 Dress properly. Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewellery or long hair can

be caught in moving parts.

 If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

 Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe

injury within a fraction of a second.

POWER TOOL USE AND CARE

 Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

 Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

 Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

 Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

 Maintain power tools. Check for misalignment or bind-

ing of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation.

If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power

tools.

3 - English

GENERAL POWER TOOL SAFETY RULES

 Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

 Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

 Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

BATTERY TOOL USE AND CARE

 Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another battery pack.

 Use power tools only with specifically designated bat-

tery packs. Use of any other battery packs may create

a risk of injury and fire.

 When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

 Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes, ad-

ditionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

 Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

of injury.

 Do not expose a battery pack or tool to fire or exces-

sive temperature. Exposure to fire or temperature above

265°F may cause explosion.

 Follow all charging instructions and do not charge the

battery pack or tool outside the temperature range

specified in the instructions. Charging improperly or at

temperatures outside the specified range may damage

the battery and increase the risk of fire.

SERVICE

 Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

 Never service damaged battery packs. Service of bat-

tery packs should only be performed by the manufacturer

or authorized service providers.

 When servicing a power tool, use only identical replace-

ment parts. Follow instructions in the Maintenance

section of this manual. Use of unauthorized parts or

failure to follow maintenance instructions may create a

risk of shock or injury.

CHAINSAW SAFETY WARNINGS

 Keep all parts of the body away from the saw chain

when the chainsaw is operating. Before you start the

chainsaw, make sure the saw chain is not contact-

ing anything. A moment of inattention while operating

chainsaws may cause entanglement of your clothing or

body with the saw chain.

 Always hold the chainsaw with your right hand on the

rear handle and your left hand on the front handle.

Holding the chainsaw with a reversed hand configuration

increases the risk of personal injury and should never be

done.

 Hold the power tool by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring. Saw chains contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

 Wear eye protection. Further protective equipment for

hearing, head, hands, legs and feet is recommended.

Adequate protective equipment will reduce personal

injury from flying debris or accidental contact with the

saw chain.

 Do not operate a chainsaw, on a ladder, from a roof-

top, or any unstable support. Operation of a chainsaw

in this manner could result in serious personal injury.

NOTE: The size of the work area depends on the job

being performed as well as the size tree or work piece

involved. For example, felling a tree requires a larger work

area than making bucking cuts.

 Do not operate a chainsaw in a tree unless you have

been specifically trained to do so. Operation of a chain-

saw in a tree without proper training could increase the

risk of serious personal injury.

 Always keep proper footing and operate the chainsaw

only when standing on fixed, secure and level surface.

Slippery or unstable surfaces such as ladders may cause

a loss of balance or control of the chainsaw.

 When cutting a limb that is under tension be alert

for spring back. When the tension in the wood fibres is

released the spring loaded limb may strike the operator

and/or throw the chainsaw out of control.

4 - English

 Use extreme caution when cutting brush and saplings.

The slender material may catch the saw chain and be

whipped toward you or pull you off balance.

 Carry the chainsaw by the front handle with the

chainsaw switched off and away from your body.

When transporting or storing the chainsaw always fit

the guide bar cover. Proper handling of the chainsaw

will reduce the likelihood of accidental contact with the

moving saw chain.

 Follow instructions for lubricating, chain tensioning

and changing the bar and chain. Improperly tensioned or

lubricated chain may either break or increase the chance

for kickback.

 Cut wood only. Do not use chainsaw for purposes not

intended. For example: do not use chainsaw for cut-

ting plastic, masonry or non-wood building materials.

Use of the chainsaw for operations different than intended

could result in a hazardous situation.

 Do not attempt to fell a tree until you have an under-

standing of the risks and how to avoid them. Serious

injury could occur to the operator or bystanders while

felling a tree.

 Follow all instructions when clearing jammed mate-

rial, storing or servicing the chainsaw. Make sure the

switch is off and the battery pack is removed. Unex-

pected actuation of the chainsaw while clearing jammed

material or servicing may result in serious personal injury.

CAUSES AND OPERATOR PREVENTION OF

KICKBACK

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches

the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse reac-

tion, kicking the guide bar up and back towards the operator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of

the saw which could result in serious personal injury. Do not

rely exclusively upon the safety devices built into your saw.

As a chainsaw user, you should take several steps to keep

your cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incorrect operat-

ing procedures or conditions and can be avoided by taking

proper precautions as given below:

 Maintain a firm grip, with thumbs and fingers encircling

the chainsaw handles, with both hands on the saw

and position your body and arm to allow you to resist

kickback forces. Kickback forces can be controlled by

the operator, if proper precautions are taken. Do not let

go of the chainsaw.

 Do not overreach and do not cut above chest height.

This helps prevent unintended tip contact and enables

better control of the chainsaw in unexpected situations.

 Only use replacement bars and chains specified by

the manufacturer. Incorrect replacement bars and chains

may cause chain breakage and/or kickback.

 Follow the manufacturer’s sharpening and mainte-

nance instructions for the saw chain. Decreasing the

depth gauge height can lead to increased kickback.

 Do not start cutting until you have a clear work area, se-

cure footing, and a planned retreat path from the falling

tree. Cluttered areas invite accidents.

 Keep ALL children, bystanders, visitors, and animals out of

the work area while starting or cutting with the chainsaw.

Do not let visitors contact chainsaw.

 Do not operate chainsaw in explosive atmospheres, such

as in the presence of flammable liquids, gases, or dust.

Chainsaws create sparks which may ignite the dust or

fumes.

 Dress Properly – Wear snug fitting clothing. Always wear

heavy, long pants, long sleeves, overalls, jeans or chaps

made of cut resistant material or ones that contain cut

resistant inserts. Wear non-slip safety footwear. Wear

non-slip heavy duty gloves to improve your grip and to

protect your hands. Do not wear jewelry, short pants,

sandals, or go barefoot. Do not wear loose fitting clothing,

which could be drawn into the motor or catch the chain

or underbrush. Secure hair so it is above shoulder level.

Wear hearing and head protection.

 Heavy protective clothing may increase operator fatigue,

which could lead to heat stroke. During weather that is

hot and humid, heavy work should be scheduled for early

morning or late afternoon hours when temperatures are

cooler.

 Always wear eye protection with side shields marked

to comply with ANSI Z87.1 as well as hearing and head

protection when operating this equipment.

 Always be aware of what you are doing when using the

chainsaw. Use common sense. Do not operate the chain-

saw when you are tired, ill, upset, or under the influence

of alcohol, drugs, or medication.

 Do not expose the chainsaw to rain.

 Do not use the chainsaw in damp or wet locations.

 Stay alert and pay attention to what you are doing. Use

common sense when using this unit.

 Keep all parts of your body away from the saw chain

when the unit is running.

 Never let anyone use your chainsaw who has not received

adequate instructions in its proper use. This applies to

rentals as well as privately owned saws.

 Before you start the unit, make sure the saw chain is not

contacting any object.

CHAINSAW SAFETY WARNINGS

5 - English

CHAINSAW SAFETY WARNINGS

 Stop the chainsaw before setting it down.

 To avoid accidental starting, never carry the unit with your

finger on the switch trigger.

 Maintain the unit with care. Keep the cutting edge sharp

and clean for best performance and to reduce the risk

of injury. Follow instructions for lubricating and changing

accessories.

 Do not operate a chainsaw with one hand! Use a firm grip

with thumbs and fingers encircling the chainsaw handles.

Serious injury to the operator, helpers, bystanders, or any

combination of these persons may result from one-handed

operation. A chainsaw is intended for two-handed use.

 Guard against electric shock – Avoid body contact with

grounded surfaces such as metal pipes and wire fences.

There is an increased risk of electric shock if your body

is grounded.

 Do not operate a chainsaw that is damaged, improperly

adjusted, or not completely and securely assembled.

Chain should slow to a stop when the switch trigger is

released. If the chain continues to turn after the switch

trigger has been released, have the unit serviced by an

authorized service center.

 Check for damaged parts. Check for alignment of mov-

ing parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged should

be properly repaired or replaced by an authorized ser-

vice center unless otherwise indicated elsewhere in this

manual.

 All chainsaw service, other than the items listed in the

operation and maintenance sections, should be performed

by an authorized service center.

 Always maintain a proper stance.

 Do not use chainsaw if switch does not turn it on and off.

Have switch replaced by an authorized service center.

 Do not adapt your power head to a bow guide or use it

to power any attachments or devices not listed for the

saw.

 Disconnect chainsaw from power supply when not in

use, before servicing, and when making adjustments and

changing attachments, such as saw chain and guard.

 Do not cut vines and/or small underbrush.

 Do not force the chainsaw. The job can be performed

better and safer at the rate for which it was intended.

 When clearing jammed material or servicing the unit,

make sure all power switches are off and the battery

pack is removed or disconnected. Unexpected actua-

tion of the chainsaw while clearing jammed material or

servicing may result in serious personal injury.

 Always use the right product for your application. The

chainsaw should be used for cutting wood only. Never

use the chainsaw to cut plastic, masonry or non-wood

building materials.

 Store chainsaw when not charging or when not in use.

Chainsaw should be stored in a dry and high or locked

area out of the reach of children. When storing chainsaw

place the scabbard on the bar and chain.

 Use this product only with batteries and chargers listed in

tool/appliance/battery pack/charger correlation supple-

ment 988000-842.

 Battery operated units do not have to be plugged into an

electrical outlet; therefore, they are always in operating

condition. Be aware of possible hazards even when unit

is not operating.

 Remove the battery pack from the chainsaw when not

charging and before cleaning, servicing, storing, removing

material from the unit, changing accessories such as the

bar and chain, or when not in use.

 Never use water or any liquids to clean or rinse off your

product and do not expose the product to rain or wet

conditions. Store indoors in a dry area. Corrosive liquids,

water, and chemicals can enter the product’s electronic

components and/or battery compartment and damage

electronic components and/or the battery pack, which can

result in a short circuit, increased risk of fire, and serious

personal injury. Remove any buildup of dirt and debris by

wiping the product clean with a dry cloth occasionally.

KICKBACK

See Figures 2 - 5.

WARNING:

Kickback may occur when the moving chain contacts an

object at the upper portion of the tip of the guide bar or

when the wood closes in and pinches the saw chain in the

cut. Contact at the upper portion of the tip of the guide

bar can cause the chain to dig into the object and stop the

chain for an instant. The result is a lightning fast, reverse

reaction which kicks the guide bar up and back toward

the operator. If the saw chain is pinched along the top of

the guide bar, the guide bar can be driven rapidly back

toward the operator. Either of these reactions can cause

loss of saw control which can result in serious injury. Do

not rely exclusively upon the safety devices built into the

saw. As a chainsaw user, you should take several steps

to keep your cutting jobs free from accident or injury.

 The following precautions should be followed to mini-

mize kickback:

• Always grip the saw firmly with both hands. Hold the

saw firmly with both hands when the unit is running.

Place your right hand on the rear handle and your left

hand on the front handle with your thumbs and fingers

encircling the chainsaw handles. A firm grip together

with a stiff left arm will help you maintain control of the

saw if kickback occurs.

6 - English

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE: (Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

CHAINSAW SAFETY WARNINGS

• Make sure that the area in which you are cutting is free

from obstructions. Do not let the nose of the guide bar

contact a log, branch, fence, or any other obstruction

that could be hit while you are operating the saw.

• Always cut with the unit running at full speed. Fully

squeeze the throttle trigger and maintain a steady cut-

ting speed.

• Use replacement parts such as low kickback chain,

chain brakes and special guide bars that reduce the

risks associated with rotational kickback. Use only

the replacement guide bars and low kickback chains

specified by the manufacturer for the saw.

 With a basic understanding of kickback, you can reduce

or eliminate the element of surprise. Sudden surprise

contributes to accidents.

 Do not overreach. Keep proper footing and balance at all

times.

 Do not cut above chest height or overreach when cutting.

Do not let the nose of the guide bar contact a log, branch,

ground, or any other obstruction while you are operating

the unit.

 Follow the sharpening and maintenance instructions for

the saw chain.

 Push and Pull – This reaction force is always opposite to

the direction the chain is moving where wood contact is

made. Thus, the operator must be ready to control the

PULL when cutting on the bottom edge of the bar, and

PUSH when cutting along the top edge.

See Figures 4-5.

UNDERSTANDING YOUR CHAINSAW

SAFETY DEVICES

LOW KICKBACK SAW CHAIN

The rakers (depth gauges) ahead of each cutter can minimize

the force of a kickback reaction by preventing the cutters

from digging in too deeply at the kickback zone. Only use

replacement chain that is equivalent to original chain or has

been certified as low kickback chain per ANSI B175.1.

Low kickback saw chain is chain that has met the kickback

performance requirements of ANSI B175.1 – 2012 (Ameri-

can National Standard for Power Tools – Gasoline-Powered

Chainsaws-Safety Requirements) when tested on the rep-

resentative sample of chainsaws below 3.8 c.i.d. specified

in ANSI B175.1 - 2012.

As saw chains are sharpened during their useful life, they

lose some of the low kickback qualities and extra caution

should be used.

GUIDE BARS

Generally, guide bars with small radius tips have somewhat

lower kickback potentials.

When making a replacement, be sure to order one of the

RYOBI bars listed for the saw in this operator’s manual.

Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you

loan someone this product, loan them these instructions

also.

7 - English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper inter-

pretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual To reduce the risk of injury, user must read and understand opera-

tor’s manual before using this product.

Wear Eye, Hearing, and

Head Protection

Wear eye protection with side shields marked to comply with

ANSI Z87.1 as well as hearing and head protection when operat-

ing this equipment.

Wet Conditions Alert

Do not expose battery, battery compartment, or electronic

components to rain, water, or liquids. Do not charge battery or

expose product to rain or damp locations.

Rain Symbol Do not expose to rain.

Operate With Two Hands Hold and operate the saw properly with both hands.

One Handed Do not operate the saw using only one hand.

Kickback DANGER! BEWARE OF KICKBACK.

Bar Nose Contact

Avoid bar nose contact. Tip contact may cause the

guide bar to move suddenly upward and backward,

which may cause serious injury.

Wear Gloves Wear non-slip, heavy-duty protective gloves when handling the

chainsaw.

Wear Safety Footwear Wear non-slip safety footwear when using this equipment.

Oil Indicator Pour bar and chain lubricant into oil tank where indicated. Do not

use any other fluids.

Recycle Symbol

This product uses lithium-ion batteries. Local, state or federal laws

may prohibit disposal of batteries in ordinary trash. Consult your

local waste authority for information regarding available recycling

and/or disposal options.

VVolts Voltage

Direct Current Type or a characteristic of current

SYMBOLS

8 - English

GLOSSARY OF TERMS

Automatic Oiler System

Lubrication is provided by the automatic oiler system. The

oiler is driven by the sprocket and adds lubrication only when

the chain is moving.

Bucking

The process of cross cutting a felled tree or log into lengths.

Chain Brake

A device used to stop the saw chain.

Chainsaw Power Head

A chainsaw without the saw chain and guide bar.

Drive Sprocket or Sprocket

The toothed part that drives the saw chain.

Felling

The process of cutting down a tree.

Felling Back Cut

The final cut in a tree felling operation made on the opposite

side of the tree from the notching undercut.

Front Hand Guard

A structural barrier between the front handle of a chainsaw

and the guide bar, typically located close to the hand posi-

tion on the front handle.

Front Handle

The support handle located at or toward the front of the

chainsaw. This handle is for the left hand.

Guide Bar

A solid railed structure that supports and guides the saw chain.

Kickback

The backward or upward motion, or both, of the guide bar

occurring when the saw chain near the nose of the top

area of the guide bar contacts any object such as a log or

branch, or when the wood closes in and pinches the saw

chain in the cut.

Kickback (Pinch)

The rapid pushback of the saw which can occur when the

wood closes in and pinches the moving saw chain in the cut

along the top of the guide bar.

Kickback (Rotational)

The rapid upward and backward motion of the saw which

can occur when the moving saw chain near the upper por-

tion of the tip of the guide bar contacts an object, such as

a log or branch.

Lock-out Button

A movable stop that prevents the unintentional operation of

the switch until manually actuated.

Low-Kickback Chain

A chain that complies with the kickback performance require-

ments of ANSI B175.1 when tested on a representative

sample of chainsaws.

Normal Cutting Position

Those positions assumed in performing the bucking and

felling cuts.

Notching Undercut

A notch cut in a tree that directs the tree’s fall.

Rear Handle

The support handle located at or toward the rear of the saw.

It normally contains the switch trigger. This handle is for the

right hand.

Reduced Kickback Guide Bar

A guide bar which has been demonstrated to reduce kick-

back significantly.

Replacement Saw Chain

A chain that complies with the kickback performance require-

ments of ANSI B175.1 when tested with specific chainsaws.

It may not meet the ANSI performance requirements when

used with other saws.

Saw Chain

A loop of chain having cutting teeth that cut the wood, and

that is driven by the motor and is supported by the guide bar.

Spiked Bumper (Spike)

The pointed tooth or teeth for use when felling or bucking to

pivot the saw and maintain position while sawing.

Springpole

A small tree (sapling) or limb that is bent or trapped under

tension. It may “spring back” rapidly when cut, causing a

dangerous situation.

Switch Trigger

A device that when operated will complete or interrupt an

electrical power circuit to the motor of the chainsaw.

9 - English

FEATURES

PRODUCT SPECIFICATIONS

Motor .................................................................. 40 Volt DC

Bar Length ...................................................................20 in.

KNOW YOUR CHAINSAW

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

CHAIN TENSIONING SCREW

This feature allows user to adjust the tension of the chain.

CHAIN BRAKE / FRONT HAND GUARD

The chain brake is designed to quickly stop the chain from

rotating. When the chain brake / front hand guard is pushed

toward the bar, the chain should stop immediately. The chain

brake does not prevent kickback.

GUIDE BAR

The factory-equipped guide bar has a small radius tip that

offers a somewhat lower kickback potential.

LOCK-OUT BUTTON

A control feature designed to prevent the motor from being

accidently started.

LOW KICKBACK CHAIN

The low kickback chain helps minimize the force of a kick-

back reaction by preventing the cutters from digging in too

deeply at the kickback zone.

QUICK VIEW OIL INDICATOR

Semi-transparent oil reservoir that allows user to see when

to add oil.

SPIKED BUMPER

Factory equipped metal teeth for use when felling or bucking

to pivot the saw and maintain position while sawing.

SWITCH TRIGGER

Squeeze the switch trigger to operate the unit after switch

lock-out has been pushed in. Release the switch trigger to

stop the unit.

ASSEMBLY

PACKING LIST

Chainsaw with Scabbard

Combination Wrench

Carrying Case

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

UNPACKING

This product has been shipped completely assembled.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the Packing

List are included.

WARNING:

Do not use this product if it is not completely assembled

or if any parts appear to be missing or damaged. Use of

a product that is not properly and completely assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

NOTE: This saw was designed for occasional light duty use and has some limitations as to what it can cut.

Chain oil tank capacity .................................................7 oz.

Chain speed ............................................................. 19 m/s

10 - English

ASSEMBLY

WARNING:

Never fell a tree or cut a log or limb that has a diameter

greater than the length of the guide bar. Only properly

trained professionals should perform these cuts. Perform-

ing these types of cuts can cause an accident and result

in death or serious personal injury.

NOTICE:

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Please contact customer service or an

authorized service center for assistance.

APPLICATIONS

You may use this product for the following purposes:

Basic limbing, felling, and wood cutting

TO INSTALL/REMOVE BATTERY PACK

See Figure 6.

WARNING:

Always remove battery pack from your tool when you are

assembling parts, making adjustments, cleaning, carry-

ing, transporting or when not in use. Removing battery

pack will prevent accidental starting that could cause

serious personal injury.

NOTE: To avoid serious personal injury, always remove the

battery pack and keep hands clear of the lock-out button

when carrying or transporting the tool.

DANGER:

Never cut near power lines, electric cords, or other elec-

tric sources. If bar and chain jams on any electrical cord

or line, DO NOT TOUCH THE BAR OR CHAIN! THEY CAN

BECOME ELECTRICALLY LIVE AND VERY DANGER-

OUS. Continue to hold the chainsaw by the insulated

rear handle or lay it down and away from you in a safe

manner. Disconnect the electrical service to the damaged

line or cord before attempting to free the bar and chain

from the line or cord. Contact with the bar, chain, other

conductive parts of the chainsaw, or live electric cords or

lines will result in death by electrocution, electric shock,

or serious personal injury.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked

to comply with ANSI Z87.1 as well as head and hearing

protection when operating this equipment. Failure to do

so could result in objects being thrown into your eyes

and other possible serious injuries.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always remove the battery pack from the

product when assembling parts.

OPERATION

11 - English

To install:

 Place the battery pack in your chainsaw. Align raised rib

on battery pack with groove in chainsaw’s battery port.

WARNING:

Make sure the latch on the battery pack snaps in place

and the battery pack is fully seated and secure in the

power head battery port before beginning operation.

Failure to securely seat the battery pack could cause the

battery pack to fall out, resulting in serious personal injury.

To remove:

Locate latch on battery pack and depress to release the

battery pack from the chainsaw.

NOTICE:

When placing battery pack in your chainsaw, be sure

raised rib on battery pack aligns with groove in chain-

saw’s battery port and latch snaps in place properly.

Improper assembly of battery pack can cause damage

to internal components.

For complete charging instructions, see the operator’s manu-

als for your battery pack and charger.

BAR AND CHAIN LUBRICATION

See Figure 7.

The bar and chain require continuous lubrication. Lubrication

is provided by the automatic oiler system when the oil tank

is kept filled. Lack of lubricant will quickly ruin the bar and

chain. Too little lubricant will cause overheating shown by

smoke coming from the chain and/or discoloration of the bar.

ADDING BAR AND CHAIN LUBRICANT

See Figure 7.

NOTICE:

Remove battery pack from unit. Fill oil tank with bar and

chain lubricant (not provided) before starting the chain-

saw. Failure to lubricate the chain will cause damage to

the bar and chain.

 Use bar and chain lubricant (not provided) that is formu-

lated to perform over a wide temperature range with no

dilution required.

NOTE: Do not use dirty, used or otherwise contaminated

lubricants. Damage may occur to the bar or chain.

 Carefully pour the bar and chain lubricant into the tank.

 Check and fill the oil tank when battery is recharged, or

as needed.

NOTE: It is normal for lubricant to seep from the saw when

not in use. To prevent seepage, empty the oil tank after each

OPERATION

use. When storing the unit for a long period of time (three

months or longer) be sure the chain is lightly lubricated; this

will prevent rust on the chain and bar sprocket.

NOTICE:

Before each use, check to make sure that the chain is

properly tensioned. A cold chain is correctly tensioned

when there is no slack on the underside of the guide bar,

the chain is snug, and it can be turned by hand without

binding. During normal saw operation, the temperature

of the chain increases. The drive links of a correctly ten-

sioned warm chain will hang approximately .050 in. out

of the bar groove. See the Adjusting the Chain Tension

instructions in the Maintenance section of this manual to

properly adjust the chain tension.

OPERATING THE CHAIN BRAKE

See Figures 8 - 9.

Check the operating condition of the chain brake prior to

each use.

Using the back of your left hand, engage the chain brake

by pushing the chain brake lever/front hand guard toward

the bar while the chain is rotating rapidly.

Reset the chain brake back into the RUN position by

grasping the top of the chain brake lever/front hand guard

and pulling toward the front handle until you hear a click.

WARNING:

If the chain brake does not stop the chain immediately, or

if the chain brake/front hand guard will not stay in the run

position without assistance, take the saw to an authorized

service center for repair prior to use.

STARTING AND STOPPING THE CHAIN SAW

See Figure 10.

WARNING:

Keep body to the left of the chain line. Never straddle the

saw or chain, or lean over past the chain line. Improper

operation of the chainsaw could result in serious personal

injury.

Starting the chainsaw:

 Slide and hold the lock-out button. This makes the switch

trigger operational.

 Press and hold the switch trigger, release the lock-out

button and continue to squeeze the switch trigger for

continued operation.

12 - English

Stopping the chainsaw:

 Release the switch trigger to stop the chainsaw.

 Upon release of the switch trigger, the lock-out button

will be automatically reset to the lock position.

This cordless chainsaw is designed for limbing and pruning

type cutting, as well as cutting small trees.

PREPARATION FOR CUTTING

PROPER GRIP ON HANDLES

See Figures 11 - 13.

Refer to Chainsaw Safety Warnings earlier in this manual for

appropriate safety equipment.

 Wear non-slip gloves for maximum grip and protection.

 Hold the saw firmly with both hands. Always keep your

left hand on the front handle and your right hand on the

rear handle so that your body is to the left of the chain

line.

WARNING:

Never use a left-handed (cross-handed) grip, or any

stance which would place your body or arm across the

chain line. Improper operation of the chainsaw could

result in serious personal injury.

 Maintain a proper grip on the saw whenever the unit is

running. The fingers should encircle the handle and the

thumb is wrapped under the handlebar. This grip is least

likely to be broken (by a kickback or other sudden reaction

of the saw). Any grip in which the thumb and fingers are

on the same side of the handle, is dangerous because a

slight kick of the saw can cause loss of control.

WARNING:

Do not operate the switch trigger with your left hand and

hold the front handle with your right hand. Never allow any

part of your body to be in the chain line while operating

a saw. Improper operation of the chainsaw could result

in serious personal injury.

PROPER CUTTING STANCE

See Figures 14 - 15.

WARNING:

Always use the proper cutting stance described in this

section. Never kneel when using the chainsaw, except

when felling a tree as illustrated in Figure 15. Kneeling

could result in loss of stability and control of the chainsaw,

resulting in serious personal injury.

 Weight should be balanced with both feet on solid ground.

 Keep left arm with elbow locked in a “straight arm” posi-

tion to withstand any kickback force.

 Your body should always be to the left of the chain line.

 Thumb should be on underside of handlebar.

BASIC CUTTING PROCEDURE

Practice cutting a few small logs on a saw-horse or cradle

using the following technique to get the “feel” of using the

saw before you begin a major sawing operation.

 Take the proper stance in front of the wood with the saw

off.

 Squeeze the switch trigger and let the chain accelerate

to full speed before entering the cut.

 Begin cutting with the saw against the log.

 Keep the unit running the entire time you are cutting,

maintain a steady speed.

 Allow the chain to cut for you; exert only light downward

pressure. If you force the cut, damage to the bar, chain,

or unit can result.

 Release the switch trigger as soon as the cut is completed,

allowing the chain to stop. If you run the saw without a

cutting load, unnecessary wear can occur to the chain,

bar, and unit.

 Do not put pressure on the saw at the end of cut.

WORK AREA PRECAUTIONS

See Figure 16.

 Cut only wood or materials made from wood, no sheet

metal, no plastics, no masonry, no non-wood building

materials.

 Never allow children to operate the saw. Allow no person

to use this chainsaw who has not read this Operator’s

Manual or received adequate instructions for the safe

and proper use of this chainsaw.

 Keep everyone – helpers, bystanders, children, and

animals – a safe distance from the cutting area. During

felling operations, the safe distance should be a least

twice the height of the largest trees in the felling area.

During bucking operations, keep a minimum distance of

15 feet between workers.

 Always cut with both feet on solid ground to prevent be-

ing pulled off balance.

 Do not cut above chest height, as a saw held higher is

difficult to control against kickback forces.

 Do not fell trees near electrical wires or buildings. Leave

this operation for professionals.

 Cut only when visibility and light are adequate for you to

see clearly.

OPERATION

13 - English

FELLING TREES

See Figures 16 - 19.

HAZARDOUS CONDITIONS

WARNING:

Do not fell trees during periods of high wind or heavy pre-

cipitation. Wait until the hazardous weather has ended.

WARNING:

Closely check for broken or dead branches, which could

fall while cutting and do not cut near buildings or elec-

trical wires if you do not know the direction of tree fall.

Do not cut at night or during bad weather conditions,

such as rain, snow, or strong winds, which can reduce

visibility and control of the chainsaw. If the tree you are

felling makes contact with any utility line, you should

discontinue use of the chainsaw and immediately notify

the utility company. Failure to follow these instructions

could result in death or serious personal injury.

When felling a tree, it is very important that you closely follow

these warnings and instructions to prevent possible death

or serious personal injury.

■Do not cut down trees having an extreme lean or large

trees with rotten limbs, loose bark, or hollow trunks. Have

these trees pushed or dragged down with heavy equip-

ment, then cut them up.

■Do not cut trees near electrical wires or buildings.

■Check the tree for damaged or dead branches that could

fall and hit you during felling.

■Periodically glance at the top of the tree during the backcut

to assure the tree is going to fall in the desired direction.

If the tree starts to fall in the wrong direction, or if the saw

gets caught or hung up during the fall, leave the saw and

save yourself!

 Felling a tree — When bucking and felling operations are

being performed by two or more persons, at the same

time, the felling operation should be separated from the

bucking operation by a distance of at least twice the

height of the tree being felled. Trees should not be felled

in a manner that would endanger any person, strike any

utility line or cause any property damage. If the tree does

make contact with any utility line, the utility company

should be notified immediately.

 Before any cuts are started, pick your escape route (or

routes in case the intended route is blocked); clear the

immediate area around the tree and make sure there are

no obstructions in your planned path of retreat. Clear

OPERATION

paths of safe retreat should extend back and diagonally

(45°) to the rear of the planned line of fall. When the tree

begins to fall, you should retreat away from the direction

of fall along a retreat path and at least 20 feet away from

the trunk in case it kicks back over the stump. See Figure

17.

 Before felling is started, consider the force and direction

of the wind, the lean and balance of the tree, and the lo-

cation of large limbs. These things influence the direction

in which the tree will fall. Do not try to fell a tree along a

line different from its natural line of fall.

 The chainsaw operator should keep on the uphill side of

the terrain as the tree is likely to roll or slide downhill after

it is felled.

 Remove dirt, stones, loose bark, nails, staples, and wire

from the tree where felling cuts are to be made.

 Notched Undercut. Cut a notch about 1/3 the diameter

of the tree, perpendicular to the direction of fall. Make the

cuts of the notch so they intersect at a right angle to the

line of fall. This notch should be cleaned out to leave a

straight line. To keep the weight of the wood off the saw,

always make the lower cut of the notch before the upper

cut. See Figure 18.

 Felling Backcut. The backcut is always made level and

horizontal, and at a minimum of 2 in. above the horizontal

cut of the notch. See Figures 18 - 19.

 Never cut through to the notch. Always leave a band of

wood between the notch and backcut (approximately 2 in.

or 1/10 the diameter of the tree). This is called “hinge” or

“hingewood.” It controls the fall of the tree and prevents

slipping or twisting or shoot-back of the tree off the stump.

See Figures 17 - 18.

 On large diameter trees, stop the back cut before it is

deep enough for the tree to either fall or settle back on

the stump. Then insert soft wooden or plastic wedges

into the cut so they do not touch the chain. The wedges

can be driven in, little by little, to help jack the tree over.

See Figure 19.

 As tree starts to fall, stop the chainsaw and put it down

immediately. Retreat along the cleared path, but watch

the action in case something falls your way. Be alert for

overhead limbs or branches that may fall and watch your

footing.

WARNING:

Never cut through to the notch when making a backcut.

The hinge controls the fall of the tree, this is the section

of wood between the notch and backcut.

14 - English

OPERATION

BUCKING

See Figures 20 - 23.

Bucking is the term used for cutting a fallen tree to the

desired log length.

 Always make sure your footing is secure and your weight

is distributed evenly on both feet.

■ Cut only one log at a time.

■ Support small logs on a saw horse or another log while

bucking.

■ Keep a clear cutting area. Make sure that no objects can

contact the guide bar nose and chain during cutting, this

can cause kickback.

 When bucking on a slope, always stand on the uphill side

of the log. To maintain complete control of the chainsaw

when cutting through the log, release the cutting pres-

sure near the end of the cut without relaxing your grip on

the chainsaw handles. Do not let the chain contact the

ground. After completing the cut, wait for the saw chain

to stop before you move the chainsaw. Always stop the

motor before moving from tree to tree.

■ Sometimes it is impossible to avoid pinching (with just

standard cutting techniques) or difficult to predict which

way a log will settle when cut. To avoid pinching while

cutting, rotate or move the log so that the pinch is elimi-

nated.

BUCKING LOGS UNDER STRESS

See Figures 23 - 24.

When the log is supported along its entire length, it should

be cut from the top or overbucking.

When the log is supported on one end, cut 1/3 the diameter

from the underside or underbucking. Then make the finishing

cut by overbucking to meet the first cut.

As the log is being cut, it will tend to bend. The saw can

become pinched or hung in the log if you make the first cut

deeper than 1/3 of the diameter of the log.

Give special attention to logs under stress to prevent the

bar and chain from pinching.

When bucking on a slope, always stand on the uphill side of

the log as shown in Figure 24. When “cutting through,” to

maintain complete control of the chainsaw, release the cutting

pressure near the end of the cut without relaxing your grip

on the chainsaw handles. Do not let the chain contact the

ground. After completing the cut, wait for the saw chain to

stop before you move the chainsaw. Always stop the motor

before moving from tree to tree.

TYPES OF CUTTING USED

See Figure 23.

OVERBUCKING

Begin on the top side of the log with the bottom of the saw

against the log; exert light pressure downward. Note that

the saw will tend to pull away from you.

UNDERBUCKING

Begin on the under side of the log with the top of the saw

against the log; exert light pressure upward. During under-

bucking, the saw will tend to push back at you. Be prepared

for this reaction and hold the saw firmly to maintain control.

LIMBING

See Figure 24.

WARNING:

Never climb into a tree to limb or prune. Do not stand on

ladders, platforms, a log, or in any position which can

cause you to lose your balance or control of the saw,

which could result in death or other serious personal

injury.

Limbing is removing branches from a fallen tree.

 Work slowly, keeping both hands on the chainsaw with

a firm grip. Always make sure your footing is secure and

your weight is distributed evenly on both feet.

 Leave the larger support limbs under the tree to keep the

tree off the ground while cutting.

 Limbs should be cut one at a time. Remove the cut limbs

from the work area often to help keep the work area clean

and safe.

 Branches under tension should be cut from the bottom

up to avoid binding the chainsaw.

 Keep the tree between you and the chainsaw while limb-

ing. Cut from the side of the tree opposite the branch you

are cutting.

PRUNING

See Figure 25.

Pruning is trimming limbs from a live tree.

 Work slowly, keeping both hands on the chainsaw with

a firm grip. Always make sure your footing is secure and

your weight is distributed evenly on both feet.

 Do not cut from a ladder, this is extremely dangerous.

Leave this operation for professionals.

 Do not cut above chest height as a saw held higher is

difficult to control against kickback.

La page charge ...

Ryobi RY405011BTL Le manuel du propriétaire

Marque: Ryobi

Modèle: RY405011BTL

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

Ce manuel convient également à

RY405110

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi RY405011BTL Owner's manual
español: Ryobi RY405011BTL El manual del propietario

Ryobi RY405011BTL Le manuel du propriétaire

Ce manuel convient également à

Ryobi RY405011BTL Le manuel du propriétaire

dans d''autres langues

Autres documents