Greenworks 2013702 48TH12 48-VOLT 12" Top Handle Chainsaw Le manuel du propriétaire

Marque: Greenworks

Modèle: 2013702 48TH12 48-VOLT 12" Top Handle Chainsaw

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

CSE403

48TH12

EN OPERATOR MANUALCHAINSAW

FR MANUEL DE L'UTILISATEURSCIE À CHAÎNE

ES MANUAL DEL OPERADORSIERRA DE CADENA

www.greenworkscommercial.com/

www.shopgreenworksgear.com/

P0801491-02 Rev B

1 Description.........................................4

1.1 Purpose.............................................................. 4

1.2 Overview........................................................... 4

2 General power tool safety

warnings.............................................4

2.1 Work area safety................................................ 4

2.2 Electrical safety................................................. 4

2.3 Personal safety...................................................4

2.4 Power tool use and care.....................................5

2.5 Battery tool use and care................................... 5

2.6 Service............................................................... 5

3 Chainsaw safety warnings................ 5

4 Prevent operator kickback............... 6

5 Symbols on the product.................... 6

6 Risk levels...........................................7

7 Environmentally safe battery

disposal...............................................7

8 Proposition 65....................................7

9 Installation......................................... 8

9.1 Unpack the machine.......................................... 8

9.2 Add the bar and chain oil...................................8

9.3 Install the battery pack.......................................8

9.4 Remove the battery pack................................... 8

10 Operation........................................... 8

10.1 Examine the chain oil........................................ 9

10.2 Hold the machine...............................................9

10.3 Start the machine............................................... 9

10.4 Stop the machine............................................... 9

10.5 Operate the chain brake..................................... 9

10.6 Prepare to cut the tree........................................ 9

10.7 The work position for two-handed use............10

10.8 Start the machine in the tree............................ 10

10.9 Operate the machine with one hand.................11

10.10 Fell a tree......................................................... 11

10.11 Limb a tree.......................................................12

10.12 Buck a log........................................................12

11 Maintenance.....................................13

11.1 Replace the guide bar and the chain................ 13

11.2 Adjust the chain tension.................................. 13

11.3 Sharpen the cutters...........................................14

11.4 Guide bar maintenance.................................... 15

12 Transportation and storage............15

13 Troubleshooting...............................15

14 Technical data..................................16

15 Limited warranty............................ 17

English EN

1 DESCRIPTION

1.1 PURPOSE

This chainsaw is designed for cutting branches, trunks, logs

and beams of a diameter determined by the cutting length of

the guide bar. It is only designed to cut wood.

It is only to be used in an outdoor, domestic application by

adults.

Do not use the chainsaw for any purpose not listed above.

It is not to be used by children or by persons not wearing

adequate personal protective equipment and clothing.

1.2 OVERVIEW

13 1514

1Guide bar cover

2Front handle guard /

chain brake

3Front handle

4Lock out button

5Trigger

6Oil tank cap

7Oil indicator

8Bucking spikes

9Chain

10 Guide bar

11 Wrench

12 Top handle

13 Chain tension screw

14 Chain cover

15 Chain cover nuts

2 GENERAL POWER TOOL

SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions. Failure to

follow the warnings and instructions may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your battery-

operated (cordless) power tool.

2.1 WORK AREA SAFETY

•Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

•Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust

or fumes.

•Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2.2 ELECTRICAL SAFETY

•Do not expose power tools to rain or wet

conditions.Water entering a power tool will increase the

risk of electric shock.

2.3 PERSONAL SAFETY

•Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence

of drugs, alcohol or medication. A lapse of attention

while operating power tools may result in serious

personal injury.

•Use personal protection. Always wear eye protection.

Protective products such as dust mask, non-skid safety

shoes, hard hat or hearing protection used appropriately

will reduce personal injuries.

•Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source

and/or battery pack and when picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energizing power tools that have the switch on

invites accidents.

•Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

•Do not over-reach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

•Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

English

•If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust related hazards.

•Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool safety

principles. A careless action can cause severe injury

within a fraction of a second.

2.4 POWER TOOL USE AND CARE

•Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

•Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

•Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

•Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

•Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

•Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

•Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

2.5 BATTERY TOOL USE AND CARE

•Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with

another battery pack.

•Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury and fire.

•When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys, nails,

screws, or other small metal objects that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or fire.

•Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with plenty of soap and water. If liquid

contacts eyes, immediately seek medical help. Liquid

ejected from the battery may cause irritation or burns.

2.6 SERVICE

•Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

3 CHAINSAW SAFETY

WARNINGS

•Keep all parts of the body away from the saw chain

when the chainsaw is operating. Before you start the

chainsaw, make sure the saw chain is not in contact

with anything. A moment of inattention while operating

chainsaws may cause entanglement of your clothing or

body with the saw chain.

•Hold the power tool by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring. Saw chains contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

•Always hold the chainsaw with your right hand at the

rear handle and your left hand at the front handle.

Holding the chainsaw with a reversed hand configuration

increases the risk of personal injury and should never be

done.

•Wear safety glasses and hearing protection. Further

protective product for head, hands, legs and feet is

recommended. Adequate protective clothing will reduce

personal injury from flying debris or accidental contact

with the saw chain.

•Do not operate a chainsaw in a tree. Operation of a

chainsaw while up in a tree may result in personal injury.

•Always keep proper footing and operate the chainsaw

only when standing on fixed, secure and level surface.

Slippery or unstable surfaces such as ladders may cause

loss of balance or control of the chainsaw.

•When cutting a limb that is under tension, be alert of

spring back. When the tension in the wood fibres is

released, the spring loaded limb may strike the operator

and/or throw the chainsaw out of control.

•Use extreme caution when cutting brush and saplings.

The slender material may catch the saw chain and be

whipped toward you or pull you off balance.

•Carry the chainsaw by the front handle with the

chainsaw switched off and away from your body.

When transporting or storing the chainsaw, always fit

the guide bar cover. Proper handling of the chainsaw

will reduce the likelihood of accidental contact with the

moving saw chain.

•Follow instructions for lubricating, chain tensioning

and changing accessories. Improperly tensioned or

lubricated chain may either break or increase the chance

for kickback.

•Keep handles dry, clean, and free from oil and grease.

Greasy, oily handles are slippery, causing loss of control.

English EN

•Cut wood only. Do not use chainsaw for purposes not

intended. For example: do not use chainsaw for

cutting plastic, masonry or non-wood building

materials. Use of the chainsaw for operations other than

intended could result in a hazardous situation.

•Fatigue causes carelessness. Be more cautious before

rest periods and towards the end of your shift.

•Personal protective clothing required by your safety

organizations, government regulations, or your

employer should be used. At all times when using a

chain saw, snug-fitting clothing, protective eyewear,

safety footwear, and hand, leg, and hearing protection

should be worn.

•Before fuelling, servicing, or transporting your chain

saw, switch off the chain saw.

•When felling, keep at least two tree lengths away from

other persons or animals.

•Plan your work, ensuring an obstacle-free work area

and, in the case of felling, have at least one escape

path from the falling tree prepared in advance.

•Follow the instructions in your operator’s manual for

starting the chain saw and control the chain saw with

a firm grip on both handles when it is in operation.

Always hold the chain saw with your right hand on the

rear handle and your left hand on the front handle. Keep

handles dry, clean, and free of oil.

•When transporting your chain saw, use the

appropriate transportation covers, which should be

available for the guide bar and saw chain.

•Never operate a chain saw that is damaged or

improperly adjusted or that is not completely and

securely assembled. Be sure that the saw chain stops

moving when the power control system trigger is

released. Never adjust the guide bar or saw chain when

the chain saw is operating.

•Do not attempt a pruning or limbing operation in a

standing tree unless specifically trained to do so.

•Guard against kickback. Kickback is the upward

motion of the guide bar that occurs when the saw

chain, at the nose of the guide bar, contacts an object.

Kickback can lead to dangerous loss of control of the

chain saw.

•A chain saw is intended for two-handed use. Serious

injury to the operator, helpers, and/or bystanders can

result from one-handed operation.

4 PREVENT OPERATOR

KICKBACK

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches the

saw chain in the cut.

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards the

operator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of the

saw which could result in serious personal injury. Do not rely

exclusively upon the safety devices built into your saw. As a

chainsaw user, you should take several steps to keep your

cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

•Maintain a firm grip, with thumbs and fingers

encircling the chainsaw handles, with both hands on

the saw and your body and arm positioned to allow

you to resist kickback forces.

Kickback forces can be controlled by the operator, if

proper precautions are taken. Do not let go of the

chainsaw.

•Do not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact and

enables better control of the chainsaw in unexpected

situations.

•Only use replacement bars and chains specified by the

manufacturer. Incorrect replacement bars and chains

may cause chain breakage and/or kickback.

•Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to increased

kickback.

5 SYMBOLS ON THE PRODUCT

Some of the following symbols may be used on this product.

Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the

product better and safer.

Symbol Explanation

Direct current - Type or characteristic

of current.

Precautions that involve your safety.

Read and understand all instructions

before operating the product, and fol-

low all warnings and safety instruc-

tions.

Wear eye and ear protection.

Do not expose the product to rain or

moist conditions.

Avoid bar nose contact.

English

Symbol Explanation

Hold with both hands.

DANGER! Be careful with kickbacks.

Wear non-slip, heavy-duty gloves.

Keep all bystanders at least 50 feet (15

m) away.

6 RISK LEVELS

The following signal words and meanings are intended to

explain the levels of risk associated with this product.

SYM-

BOL

SIGNAL MEANING

DANGER Indicates an imminently haz-

ardous situation, which, if not

avoided, will result in death

or serious injury.

WARNING Indicates a potentially hazard-

ous situation, which, if not

avoided, could result in death

or serious injury.

CAUTION Indicates a potentially hazard-

ous situation, which, if not

avoided, may result in minor

or moderate injury.

CAUTION (Without Safety Alert Sym-

bol) Indicates a situation that

may result in property dam-

age.

7 ENVIRONMENTALLY SAFE

BATTERY DISPOSAL

The toxic and corrosive materials below are in the batteries

used in this machine: Lithium-Ion, a toxic material.

WARNING

Discard all toxic materials in a specified manner to prevent

contamination of the environment. Before discarding

damaged or worn out Li-ion battery, contact your local

waste disposal agency, or the local Environmental

Protection Agency for information and specific instructions.

Take the batteries to a local recycling and/or disposal center,

certified for lithium-ion disposal.

WARNING

If the battery pack cracks or breaks, with or without leaks,

do not recharge it and do not use. Discard it and replace

with a new battery pack. DO NOT TRY TO REPAIR IT! To

prevent injury and risk of fire, explosion, or electric shock,

and to avoid damage to the environment:

• Cover the terminals of the battery with heavy-duty

adhesive tape.

• DO NOT try to remove or destroy any of the battery

pack components.

• DO NOT try to open the battery pack.

• If a leak develops, the released electrolytes are

corrosive and toxic. DO NOT get the solution in the

eyes or on skin, and do not swallow it.

• DO NOT put these batteries in your regular household

trash.

• DO NOT incinerate.

• DO NOT put them where they will become part of any

waste landfill or municipal solid waste stream.

• Take them to a certified recycling or disposal center.

8 PROPOSITION 65

WARNING

This product contains a chemical known to the state of

California to cause cancer, birth defects or other

reproductive harm. Some dust created by power sanding,

sawing, grinding, drilling, and other construction activities

contains chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals

are:

• Lead from lead-based paints;

• Crystalline silica from bricks and cement and other

masonry products;

• Arsenic and chromium from chemically treated lumber.

Your risk of exposure to these chemicals varies depending

on how often you do this type of work. To reduce your

exposure to these chemicals, work in a well-ventilated area,

and work with approved safety equipment, such as dust

masks that are specially designed to filter out microscopic

particles.

Save these instructions.

English EN

9 INSTALLATION

WARNING

Do not change or use accessories that are not recommended

by the manufacturer.

WARNING

Do not install battery pack until you assemble all the parts.

9.1 UNPACK THE MACHINE

WARNING

Make sure that you correctly assemble the machine before

use.

WARNING

• If parts of the machine are damaged, do not use the

machine.

• If you do not have all the parts, do not operate the

machine.

• If parts are damaged or missing, contact the service

center.

1. Open the package.

2. Read the documentation provided in the box.

3. Remove all the unassembled parts from the box.

4. Remove the machine from the box.

5. Discard the box and packing material in compliance with

local regulations.

9.2 ADD THE BAR AND CHAIN OIL

Examine the amount of oil in the machine. If the oil level is

low, add the bar and chain oil as follows.

IMPORTANT

Use bar and chain oil that is only for chains and chain

oilers.

NOTE

The machine comes from the factory without bar and chain

oil.

1. Loosen and remove the cap (6) from the oil tank.

2. Put the oil into the oil tank.

3. Monitor the oil indicator (7) to make sure that no dirt gets

into the oil tank while you add the oil.

4. Put the oil cap on.

5. Tighten the oil cap.

6. The whole oil tank will last for approximately 20- 40

minutes.

IMPORTANT

Do not use dirty, used or contaminated oil. Damage can

occur to the bar or chain.

9.3 INSTALL THE BATTERY PACK

WARNING

• If the battery pack or charger is damaged, replace the

battery pack or the charger.

• Stop the machine and wait until the motor stops before

you install or remove the battery pack.

• Read and understand the instructions in the battery and

charger manual.

1. Align the lift ribs on the battery pack with the grooves in

the battery compartment.

2. Push the battery pack into the battery compartment until

the battery pack locks into place.

3. When you hear a click, the battery pack is installed.

9.4 REMOVE THE BATTERY PACK

1. Push and hold the battery release button (18).

2. Remove the battery pack from the machine.

10 OPERATION

NOTE

Remove the battery pack and keep hands clear of the lock

out button when you move the machine.

IMPORTANT

Examine the chain tension before each use.

English

10.1 EXAMINE THE CHAIN OIL

NOTE

Do not use the machine without sufficient chain oil.

1. Examine the oil level of the machine from the oil

indicator.

2. Add oil if necessary.

10.2 HOLD THE MACHINE

1. Hold the chainsaw with your right hand on the top handle

and left hand on the front handle.

2. Hold the handles with the thumbs and the fingers around

them.

3. Make sure that your left hand holds the front handle and

your thumb is below the handle.

10.3 START THE MACHINE

1. Press the on/off switch (40).

2. Press the lock-out button (4).

3. Press the trigger (5) while you hold the lock-out button.

4. Release the lock-out button.

NOTE

The machine has an automatic stop function that stops the

machine if you do not use it for one minute.

IMPORTANT

The chain brake must be disengaged for the chain saw to

start. Activate the brake by moving the front hand guard

forwards.

10.4 STOP THE MACHINE

1. Release the trigger to stop the machine.

10.5 OPERATE THE CHAIN BRAKE

WARNING

Make sure that your hands are on the handles at all times.

1. Start the machine.

2. Push the guard forward to to engage the chain brake.

3. Pull the handle guard / chain brake backwards to

disengage the chain brake.

4. Call approved service center for repair before use if

• The chain brake does not stop the chain immediately.

• The chain brake does not stay in the disengaged

position without aid.

10.6 PREPARE TO CUT THE TREE

English EN

IMPORTANT

Do not work alone when you are working at height from a

rope and harness. You must:

• get help from a ground worker trained in applicable

emergency procedures.

• be trained in general safe climbing and work

positioning techniques.

• have correct harnesses, ropes, strops, carabiners and

other equipment.

Examine, charge up, start and warm up the machine.

Switch off the machine before you send it up to the operator

in the tree.

Make sure that the machine has a correct strop for attachment

to the harness.

• Secure the strop around the attachment point on the rear

of the saw.

• Attach the machine to the harness directly or indirectly

with correct carabiner.

• Make sure that the machine is safely attached when it is

being sent up to the operator.

• Make sure that the machine is secured to the harness

before it stops rising.

• Always switch the machine off when it is directly

attached to the harness.

Attach the machine to the recommended attachment points on

the harness (mid-point or at the sides).

When changing the attachment point to another, make sure

that the machine is secured in the new position before

releasing the previous attachment point.

10.7 THE WORK POSITION FOR TWO-

HANDED USE

NOTE

An analysis of accidents with the machine during tree

service operations shows the primary cause is inappropriate

one-handed use of the machine. In the vast majority of

accidents, operators do not use a safe work position that let

them hold both handles of the machine. Not hold the

machine firmly results in an increased risk of injury. If it

kicks back, it is more likely to touch climbing lines and the

operator’s body (particularly the left hand and arm).

• To use the machine with both hands, as a general rule

operators must aim for a safe work position in:

• hip level, when cutting horizontal sections, and

• solar plexus level, when cutting vertical sections.

• When operator is working close into vertical stem with

low lateral forces on the work position, a good footing

could be all that is needed to maintain a safe work

position.

• When operators move away from the stem, it is necessary

to remove or counteract the increasing lateral forces by

• a redirect of the main line via a supplementary anchor

point, or

• use of an adjustable strop direct from the harness to

supplementary anchor point.

10.8 START THE MACHINE IN THE

TREE

1. Apply the chain brake before starting.

2. Hold the machine with your left hand on the front handle.

3. Thrust the machine away from your body while holding

the pull starter cord in your right hand.

4. Hold the machine with your right hand on either handle.

5. Thrust the machine away from your body while holding

the pull starter cord in your left hand.

English

NOTE

• The chain brake must always be engaged before a

running machine is lowered onto its strop.

• Examine that the machine has sufficient energy before

doing critical cuts.

10.9 OPERATE THE MACHINE WITH

ONE HAND

NOTE

Do not use the machine with one hand when work position

is unstable or in preference to a handsaw when cutting small

diameter wood at the branch tips.

Operate the machine with one hand only when:

• You cannot get a work position enabling two-handed

operation.

• You need to support the working position with one hand.

• The machine is being used at full stretch, at right angles

to and out of line with your body.

Do not:

• Cut with the kickback zone at the tip of the saw guide bar.

• "Hold and cut" sections, or.

• Attempt to catch falling sections.

10.10 FELL A TREE

It is recommended that the first-time user should, as a

minimum practice, start cutting logs on a saw-horse or cradle.

Before you start to fell a tree, make sure that:

• The minimum distance between the areas of bucking and

felling performed by two or more persons at the same

time is two times the height of the tree felled.

• The operation does not:

• Cause injury to personnel.

• Hit utility lines. If the tree touches utility lines,

immediately tell the utility company.

• Cause losses in property.

• The user is not in the danger area (24), for example, the

downhill side of the area.

• The escape paths (25) that extend back and diagonally

behind the felling direction (23) are clear. The felling

direction is controlled by:

• The natural lean of the tree.

• The location of larger branches.

• The wind direction.

• Ensure there is no dirt, stones, loose bark, nails, or staples

on the tree.

2’’(50mm)

1. Make a lower level notching cut (27). Make sure that

this cut is:

a) 1/3 width of the diameter of the tree.

b) Perpendicular to the felling direction.

CAUTION

The level notching cut helps prevent pinching of the

saw chain or the guide bar when you make the second

notch.

2. Make the felling cut (28) no less than 2 in. (50 mm) or

higher than the level notching cut. Make sure that this

cut:

a) Is parallel to the level notching cut.

b) Keeps sufficient wood 2 in. (50 mm) or 1/10 the

diameter of the tree to become a hinge (29) which

prevents the tree from twisting and felling in the

wrong direction.

When the felling cut (28) gets near the hinge (29), the tree

falls. Stop the felling cut if the tree:

• Does not fall in the correct direction or

• Moves backwards, causing the cutting bar and chain

to become stuck in the cut.

3. Use felling wedge to open the cut and let the tree fall

in the correct direction.

English EN

4. When the tree starts to fall:

a) Remove the chainsaw from the cut.

b) Stop the machine.

c) Put the machine down.

d) Move away from the tree via the escape path (25).

Always keep watching the tree to see the direction of

fall. Be careful with overhead branches and your

footing.

10.11 LIMB A TREE

Limbing is the removal of the branches from a fallen tree.

1. Keep the larger lower branches to hold the log off the

ground (31).

2. Remove the small limbs (30) in one cut.

3. Limb the branches with tension from the bottom to top.

4. Keep the larger lower branches as a support until the log

is limbed.

10.12 BUCK A LOG

To buck is to cut a log into lengths.

CAUTION

Do not let the chainsaw touch the ground.

It is important to make sure your footing is secure and your

weight is evenly distributed. If possible, lift the log and hold

it with branches, logs or chock. Obey the instructions below:

When the log is held along the full length (32), cut it from the

top (33).

When the log is held on one end (34):

1. Cut the first time 1/3 of the diameter from the bottom

(35).

2. Cut the second time from the top (36) to complete the

bucking.

37 35

When the log is held on two ends (37):

1. Cut the first time 1/3 of the diameter from the top (36).

2. Cut the second time lower 2/3 from the bottom to

complete the bucking (35).

When the log is on a slope:

1. Stand on the uphill side.

2. Control the chainsaw completely.

3. Hold the chainsaw handles tightly.

4. Release the cutting pressure near the end of the cut.

When bucking is complete (38):

1. Wait for the chain to stop (39).

English

2. Ensure the chainsaw is turned off.

3. Check for hazards before you move to another tree.

11 MAINTENANCE

CAUTION

Do not let brake fluids, gasoline, petroleum-based materials

touch the plastic parts. Chemicals can cause damage to the

plastic, and make the plastic unserviceable.

CAUTION

Do not use strong solvents or detergents on the plastic

housing or components.

WARNING

Remove the battery pack from the machine before

maintenance.

11.1 REPLACE THE GUIDE BAR AND

THE CHAIN

1. Remove the chain cover nuts with the wrench (11).

2. Remove the chain cover.

3. Put the chain drive links (21) into the bar groove (20).

4. Put the chain cutters (22) in the direction of the chain

operation.

5. Put the chain in position and make sure that the loop is

behind the guide bar.

6. Hold the chain and bar.

7. Put the chain loop around the sprocket (16).

8. Make sure the chain tension pin hole (19) on the guide

bar fits correctly with the bolt (17).

17 19

9. Install the chain cover.

10. Tighten the chain. Refer to Adjust the chain tension.

11. Tighten the nuts when the chain is correctly tensioned.

NOTE

If you start the chain saw with a new chain, have a test for

2-3 minutes. A new chain gets longer after the first use,

examine the tension and tighten the chain if necessary.

11.2 ADJUST THE CHAIN TENSION

The more you use a chain the longer it becomes. It is

therefore important to adjust the chain regularly to take up the

slack.

Tension the chain so that it can only just be pulled away from

the bar at its centre point.

WARNING

A slack chain may jump off and cause serious or even fatal

injury.

CAUTION

Wear protective gloves if you touch the chain, bar or areas

around the chain.

1. Stop the machine.

2. Loosen the lock nuts with the wrench.

English EN

NOTE

It is not necessary to remove the chain cover to adjust the

chain tension.

3. Turn the chain adjustment screw clockwise to increase

the chain tension.

4. Turn the chain adjustment screw counterclockwise to

decrease the chain tension.

5. When the chain is at the wanted tension, tighten the lock

nuts.

NOTE

During normal saw operation, the temperature of the chain

increases. The drive links of a correctly tensioned warm

chain will hang approximately 1/16 in. (1,58 mm) out of the

bar groove.

1/16 in. (1,58 mm)

11.3 SHARPEN THE CUTTERS

Sharpen the cutters if chain does not go into wood easily.

NOTE

We recommend that a service center, which has an electric

sharpener, perform important sharpening work.

1. Tensioning chain.

2. Sharpen the cutters corner with a 5/32 in. (4 mm)

diameter round file .

3. Sharpen the top plate, side plate and depth gauge with a

flat file.

4. File all the cutters to the specified angles and the same

length.

NOTE

During the process:

• Keep the file flat with the surface to be sharpened.

• Use the midpoint of the file bar.

• Use light but firm pressure when sharpening the

surface.

• Lift the file away on each return stroke.

• Sharpen the cutters on one side and then move to the

other side.

Replace the chain if:

• The length of the cutting edges is less than 1/5 in. (5

mm).

English

• There is too much space between the drive links and the

rivets.

• The cut speed is slow.

• Sharpening the chain many times but it does not increase

the cutting speed. The chain is worn.

11.4 GUIDE BAR MAINTENANCE

NOTE

Make sure that the bar is turned over periodically to keep

symmetrical wear on the bar.

1. Lubricate the bearings on the nose sprocket (if present)

with the syringe (not included).

2. Clean the bar groove with the scraping hook (not

included).

3. Clean the lubrication holes.

4. Remove burr from the edges and level the cutters with a

flat file.

Replace the bar if:

• the groove does not fit with the height of the drive links

(which must never touch the bottom).

• the inside of the guide bar is worn and makes the chain

lean to one side.

12 TRANSPORTATION AND

STORAGE

Before you move the machine, always

• Remove the battery pack from the machine.

• Keep hands clear of the lock-out button.

• Put the scabbard on the guide bar and the chain.

Before you put the machine into storage, always

• Remove all residual oil from the machine.

• Remove the battery pack from the machine.

• Clean all unwanted material from the machine.

• Make sure that the storage area is

• Not available to children.

• Away from agents which can cause corrosion, such as

garden chemicals and de-icing salts.

13 TROUBLESHOOTING

Problem Possible cause Solution

The guide bar and

the chain become

hot and release

smoke.

The chain is too

tight.

Adjust the chain

tension.

The oil tank is

empty.

Add oil.

Contamination

causes a blockage

of the discharge

port.

Remove the guide

bar and clean the

discharge port.

Contamination

causes a blockage

of the oil tank.

Clean the oil tank.

Add new oil.

Contamination

causes a blockage

of the guide bar

and the oil tank

cap.

Clean the guide

bar and the oil

tank cap.

Contamination

causes a blockage

of the sprocket or

guide wheels.

Clean the sprocket

and the guide

wheels.

English EN

Problem Possible cause Solution

The motor runs

but the chain does

not rotate.

The chain is too

tight.

Adjust the chain

tension.

The guide bar and

the chain are dam-

aged.

Replace the guide

bar and the chain

if it is necessary.

The motor is dam-

aged.

1. Remove the

battery pack

from the ma-

chine.

2. Remove the

guide bar cov-

er.

3. Remove the

bar and saw

chain.

4. Clean the ma-

chine.

5. Install battery

pack and oper-

ate the ma-

chine.

If the sprocket ro-

tates, it means the

motor works prop-

erly. If not, call

service center.

The motor runs

and the chain ro-

tates, but the chain

does not cut.

The chain is blunt. Sharpen or replace

the saw chain.

The chain is in the

incorrect direction.

Turn the chain

loop to the other

direction.

The chain is tight

or loose.

Adjust the chain

tension.

Problem Possible cause Solution

The machine does

not start. The chain brake is

engaged.

Pull the chain

brake in the direc-

tion of the user to

disengage it.

The machine and

battery are not

connected correct-

ly.

Make sure that the

battery release

button clicks when

you install the bat-

tery pack.

The battery level

is low.

Charge the battery

pack.

The lock out but-

ton and the trigger

are not pushed at

the same time.

1. Push the lock-

out button and

hold it.

2. Push the trig-

ger to start the

machine.

The battery is too

hot or too cold.

Refer to battery

and charger man-

ual.

The motor runs,

but the chain does

not cut correctly,

or the motor stops

after around 3 sec-

onds.

The machine is in

the protection

mode to protect

the PCB.

Release the trigger

and start the ma-

chine again. Do

not force the ma-

chine to cut.

The battery is not

charged.

Charge the battery.

Refer to the bat-

tery and charger

manual for correct

charging proce-

dures.

The chain is not

lubricated.

Lubricate the

chain to decrease

the friction. Do

not let the guide

bar and the chain

operate without

sufficient oil.

Incorrect battery

storage tempera-

ture

Cool the battery

pack until it de-

creases to the am-

bient temperature.

14 TECHNICAL DATA

Voltage 48 V DC

No load speed 20 m/s

Guide bar length 12'' (305 mm)

Chain pitch 3/8" LP (9.5 mm)

Chain gauge .050" (1.27 mm)

English

Drive links 45

Chain oil capacity 150 ml

Weight (without battery

pack)

7.5 lbs (3.4 kg)

Chain 91PJ045X/CL15045

Guide bar 120SDEA041/

M1501245-1041TL

Battery model 48B4AH and other BAM

series

Charger model CAM803 and other CAM

series

The recommended ambient temperature range:

Item Temperature

Appliance storage tempera-

ture range

32°F (0°C) - 113°F (45°C)

Appliance operation temper-

ature range

32°F (0°C) - 113°F (45°C)

Battery charging temperature

range

39°F (4°C) - 104°F (40°C)

Charger operation tempera-

ture range

39°F (4°C) - 104°F (40°C)

Battery storage temperature

range

32°F (0°C) - 113°F (45°C)

Battery discharging tempera-

ture range

32°F (0°C) - 113°F (45°C)

15 LIMITED WARRANTY

Greenworks hereby warranties this product, to the original

purchaser with proof of purchase, 2 year commercial power

train warranty, 2 year commercial battery warranty against

defects in materials, parts or workmanship. Greenworks, at its

own discretion will repair or replace any and all parts found

to be defective, through normal use, free of charge to the

customer. This warranty is valid only for units which have

been used for personal or commercial use, and that have been

maintained in accordance with the instructions in the owners’

manual supplied with the product from new.

2 YEAR LIMITED POWER TRAIN WARRANTY

COVERAGE:

– Motor

– PCB Boards

– Gear Box

– 2 years from the date of purchase (non transferable)

2 YEAR LIMITED BATTERY WARRANTY

COVERAGE:

– Greenworks Commercial Battery Packs (48B4AH)

– 2 year from the date of purchase (non transferable)

60 DAY LIMITED WEARABLE PARTS WARRANTY

COVERAGE:

– Bars

– Blades

– Guards

– Chains

– Bump Feed Heads

– Tines

– 60 Days from date of purchase (non transferable)

WARRANTY EXCLUSIONS, LIMITATIONS AND

RIGHTS:

1. All warranties may not be transferred by the consumer to

any subsequent purchaser.

2. Parts or components not supplied by the warrantor, or

parts or components that have been modified.

3. Any failure resulting from the use of improper tools or

improper repair procedures.

4. Any failure resulting from the use of improper tools or

improper repair procedures.

5. Any failure or part that has become inoperative due to

accident, impact, abuse, misuse, neglect, mishandling,

dulling of cutting edges, or failure to operate the product

in accordance with the information provided in the

instruction manual supplied with the product.

6. Routine maintenance items such as lubricants, blade

sharpening.

7. The unit, if it has not been operated and/or maintained in

accordance with the owner's manual.

8. The unit, if it has not been operated and/or maintained in

accordance with the owner's manual.

GREENWORKS HELPLINE:

Warranty service is available by calling our toll-free helpline,

at 1-855-470-4267.

TRANSPORTATION CHARGES:

Transportation charges for the movement of any power

equipment unit or attachment are the responsibility of the

purchaser. It is the purchaser’s responsibility to pay

English EN

transportation charges for any part submitted for replacement

under this warranty unless such return is requested in writing

by Greenworks.

USA address: Canadian address:

Greenworks Tools Greenworks Tools Canada Inc.

P.O. Box 1238 P.O. Box 93095, Newmarket,

Ontario

Mooresville, NC 28115 L3Y 8K3

English

1 Description.......................................20

1.1 But................................................................... 20

1.2 Aperçu............................................................. 20

2 Avertissements généraux de

sécurité des outils électriques......... 20

2.1 Sécurité de la zone de travail...........................20

2.2 Sécurité électrique........................................... 20

2.3 Sécurités des personnes................................... 20

2.4 Utilisation et entretien des outils électriques...21

2.5 Utilisation et entretien de l’outil à batterie...... 21

2.6 Service............................................................. 21

3 Avertissements de sécurité de la

tronçonneuse....................................21

4 Prévention des rebonds...................22

5 Symboles figurant sur la

machine............................................ 23

6 Niveaux de risques...........................23

7 Élimination des batteries sans

danger pour l'environnement.........23

8 Proposition 65..................................24

9 Installation....................................... 24

9.1 Déballer la machine.........................................24

9.2 Ajoutez le lubrifiant de guide-chaîne et

chaîne...............................................................25

9.3 Installez la batterie...........................................25

9.4 Retirer le bloc-batterie.....................................25

10 Utilisation.........................................25

10.1 Examiner la lubrification de la chaîne.............25

10.2 Tenez la machine............................................. 25

10.3 Démarrez la machine.......................................26

10.4 Arrêter la machine........................................... 26

10.5 Actionnez le frein de la tronçonneuse............. 26

10.6 Préparation pour la coupe de l’arbre................26

10.7 La position de travail pour une utilisation

à deux mains.................................................... 27

10.8 Redémarrez la machine dans l’arbre............... 27

10.9 Utilisez la machine en tenant fermement

avec une main.................................................. 27

10.10 Abattre un arbre...............................................28

10.11 Ébrancher un arbre...........................................28

10.12 Couper une bûche............................................ 29

11 Entretien...........................................29

11.1 Assemblage du guide-chaîne et de la chaîne...30

11.2 Réglez la tension de la chaîne..........................30

11.3 Affûter les dents...............................................31

11.4 Entretien du guide-chaîne................................32

12 Transport et entreposage................ 32

13 Dépannage........................................32

14 Données techniques......................... 34

15 Garantie limitée...............................34

Français

1 DESCRIPTION

1.1 BUT

Cette scie à chaîne est conçue pour la coupe de branches,

troncs, grumes et poutres d'un diamètre déterminé par la

longueur de coupe du guide-chaîne. Elle est uniquement

conçue pour couper du bois.

Elle ne doit être utilisée qu'à l'extérieur, à des fins

domestiques, par des adultes.

N'utilisez pas la scie à chaîne à des fins autres que celles

mentionnées ci-dessus.

Elle ne doit pas être utilisée par des enfants ou par des

personnes ne portant pas un équipement et des vêtements de

protection individuelle adéquats.

1.2 APERÇU

13 1514

1Couvercle du guide-

chaîne

2Garde protectrice de

la poignée avant /

frein de la chaîne

3Guidon avant

4Bouton de

verrouillage

5Gâchette

6Bouchon du réservoir

d’huile

7Indicateur d’huile

8Pointes de

tronçonnage

9Chaîne

10 Guide-chaîne

11 Clé

12 Poignée supérieure

13 Vis de tension de

chaîne

14 Couvre-chaîne

15 Écrous du couvre-

chaîne

2 AVERTISSEMENTS

GÉNÉRAUX DE SÉCURITÉ

DES OUTILS ÉLECTRIQUES

AVERTISSEMENT

Lisez tous les avertissements de sécurité et toutes les

instructions. Le non-respect de ces avertissements et de ces

instructions peut entraîner un choc électrique, un incendie

et/ou des blessures graves.

Conservez tous les avertissements et instructions pour

référence ultérieure.

Le terme « outil électrique » dans les avertissements fait

référence à votre outil électrique (sans fil) fonctionnant sur

batterie.

2.1 SÉCURITÉ DE LA ZONE DE

TRAVAIL

•Gardez la zone de travail propre et bien éclairée. Les

endroits encombrés ou sombres favorisent les accidents.

•N'utilisez pas les outils électriques dans des

environnements explosifs, par exemple en présence de

liquides, gaz ou poussières inflammables. La mise en

marche des outils électriques crée des étincelles qui

peuvent enflammer la poussière ou les vapeurs.

•Tenez les enfants et les curieux à l'écart lorsque vous

utilisez un outil électrique. Les distractions peuvent

vous faire perdre le contrôle.

2.2 SÉCURITÉ ÉLECTRIQUE

•N'exposez pas les outils électriques à la pluie ou à des

conditions humides. L'eau qui pénètre dans un outil

électrique augmente le risque de choc électrique.

2.3 SÉCURITÉS DES PERSONNES

•Restez vigilant, soyez attentif à ce que vous faites et

faites preuve de bon sens lorsque vous utilisez un outil

électrique. N’utilisez pas l’appareil lorsque vous êtes

fatigué, sous l’emprise de l’alcool ou de drogues ou

après avoir pris des médicaments. Un simple moment

d’inattention lors de l’utilisation d’un outil électrique

peut provoquer des blessures corporelles graves.

•Utilisez des équipements de protection individuelle.

Portez toujours des lunettes de protection. L’utilisation

d’équipements de protection adaptés aux conditions de

travail (masque anti-poussières, chaussures de sécurité

antidérapantes, casque et protections auditives etc.)

permet de réduire les risques de blessures corporelles.

•Évitez tout démarrage accidentel. Assurez-vous que

l'interrupteur est en position d'arrêt avant de

brancher à la source d’alimentation et/ou la batterie et

quand vous soulevez ou transportez l'appareil.

Transporter un outil électrique avec un doigt sur

l’interrupteur ou le brancher sur une alimentation

Français

électrique alors que son interrupteur est en position

marche favorise les accidents.

•Retirez les clefs de réglage et de serrage avant de

mettre l’outil en marche. Une clef de réglage ou de

serrage restée sur une pièce en rotation de l’outil

électrique peut entraîner des blessures corporelles.

•Ne vous penchez pas trop en avant. Gardez un bon

équilibre en tout temps. Ceci permet un meilleur

contrôle de l'outil électrique dans des situations

inattendues.

•Habillez-vous correctement. Ne portez pas de

vêtements amples ou de bijoux. Veillez à ne pas

approcher vos cheveux, vos vêtements et vos gants des

pièces en mouvement. Les vêtements amples, les bijoux

et les cheveux longs peuvent se prendre dans les pièces en

mouvement.

•Si un appareil est conçu pour être utilisé avec des

dispositifs d’extraction et de récupération des

poussières, veillez à ce que ces dispositifs soient bien

raccordés et correctement utilisés. L’utilisation de

dispositifs de récupération des poussières permet de

réduire les risques liés aux poussières.

•Ne laissez pas l'habitude des fréquentes utilisations

vous faire oublier et ignorer les principes de sécurité.

Une action négligente peut provoquer de graves blessures

en une fraction de seconde.

2.4 UTILISATION ET ENTRETIEN DES

OUTILS ÉLECTRIQUES

•Ne forcez pas l’outil électrique. Utilisez l'outil

l’électrique adapté à votre application. L'outil

électrique approprié fera mieux le travail et sera plus

sécuritaire au rythme pour lequel il a été conçu.

•N’utilisez pas l'outil électrique si l'interrupteur ne le

met pas en marche ou à l'arrêt. Tout outil électrique qui

ne peut pas être contrôlé avec l'interrupteur est

dangereux et doit être réparé.

•Débranchez la prise de la source d’alimentation et/ou

de la batterie avant d'effectuer des réglages, de

changer des accessoires ou de ranger l'outil électrique.

De telles mesures de sécurité préventives réduisent le

risque d'un démarrage accidentel de l'outil électrique.

•Rangez les outils électriques inutilisés hors de portée

des enfants et ne laissez pas des personnes qui ne se

sont pas familiarisées avec l'outil électrique ou ces

instructions l’utiliser. Les outils électriques sont

dangereux entre les mains des utilisateurs non formés.

•Entretenir les outils électriques. Vérifiez le

désalignement des pièces mobiles ou la fixation des

pièces mobiles, la cassure des pièces et toute autre

condition qui pourrait affecter le fonctionnement de

l’outil électrique. Si il est endommagé, faites réparer

l'outil électrique avant de l'utiliser. De nombreux

accidents sont causés par des outils électriques mal

entretenus.

•Garder les outils de coupe propres et tranchants. Les

outils de coupe bien entretenus avec des bords tranchants

sont moins susceptibles de se coincer et sont plus faciles

à contrôler.

•Utilisez l'outil électrique, les accessoires, les mèches,

etc. conformément à ces instructions, en tenant

compte des conditions de travail et des travaux à

effectuer. L'utilisation de l'outil motorisé pour des

opérations différentes de celles prévues pourrait

entraîner une situation dangereuse.

2.5 UTILISATION ET ENTRETIEN DE

L’OUTIL À BATTERIE

•Rechargez uniquement avec le chargeur spécifié par le

fabricant. Un chargeur adapté à un type de bloc-batterie

peut créer un risque d'incendie lorsqu'il est utilisé avec

un autre bloc-batterie.

•Utilisez les outils électriques uniquement avec des

batteries spécialement conçues à cet effet. L'utilisation

de tous autres bloc-batteries peut créer un risque de

blessure et d'incendie.

•Lorsque la batterie n'est pas utilisée, éloignez-la des

autres objets métalliques tels qu’attaches trombones,

pièces de monnaie, clés, clous, vis ou autres petits

objets métalliques qui peuvent établir une connexion

d'une borne à une autre. Le court-circuitage des bornes

de la batterie peut provoquer des brûlures ou un incendie.

•Dans des conditions abusives, du liquide peut être

éjecté de la batterie ; évitez tout contact. En cas de

contact accidentel, rincez abondamment avec du

savon et de l’eau. En cas de contact du liquide avec les

yeux, consultez immédiatement un médecin. Le liquide

s'échappant des batteries peut causer des irritations ou

des brûlures.

2.6 SERVICE

•Faites effectuer l'entretien de votre outil électrique

par un réparateur qualifié en n'utilisant que des

pièces de rechange identiques. Cela garantira le

maintien de la sécurité de l’outil électrique.

3 AVERTISSEMENTS DE

SÉCURITÉ DE LA

TRONÇONNEUSE

•Veillez à ce qu’aucune partie du corps ne s’approche

de la chaîne lorsque la scie à chaîne est en marche.

Avant de démarrer la scie à chaîne, vérifiez que la

chaîne n’est en contact avec aucun objet. Lors de

l’utilisation d’une tronçonneuse, un simple moment

d’inattention suffit pour que vos vêtements se prennent

dans la chaîne ou qu’une partie de votre corps entre en

contact avec celle-ci.

•Tenez toujours l’appareil par ses poignées isolantes.

La lame peut à tout moment entrer en contact avec un

fil électrique caché. Si une tronçonneuse entre en contact

avec un fil électrique sous tension, les parties métalliques

non carénées de l’outil peuvent se retrouver sous tension

et l’opérateur risque d’être électrocuté.

Français

La page charge ...

Greenworks 2013702 48TH12 48-VOLT 12" Top Handle Chainsaw Le manuel du propriétaire

Marque: Greenworks

Modèle: 2013702 48TH12 48-VOLT 12" Top Handle Chainsaw

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

Greenworks 2013702 48TH12 48-VOLT 12" Top Handle Chainsaw Le manuel du propriétaire

Greenworks 2013702 48TH12 48-VOLT 12" Top Handle Chainsaw Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents