Naomi Home 99352 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Page 1 of 9
Nailhead Headboard
Assembly Instructions
Product Dimensions:
62”W×3”D×48”H
Please take a moment to read through the entire instruction booklet before assembly to
familiarize yourself with this product. Once you feel ready to start, follow the instructions
step by step and this should make this process as easy as we could make it for you.
.
Page 2 of 9
WARNING
!
ADULT ASSEMBLY REQUIRED
CHOKING HAZARD
CAUTION
This product includes small parts, sharp points and sharp edges in its unassembled state.
Keep unassembled parts away from children under 3 years of age, and animals.
SAFETY WARNINGS
Follow the information on the warnings appearing on headboard and on the
carton. Do not remove warning label from headboard.
Do not allow children under 3 years of age to use the headboard .
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
FURNITURE TIP-OVER HAZARD
Children have died from furniture tip-over
To reduce the risk of furniture tip-over:
ALWAYS install tip-over restraint especially if used by a wall or in the open.
NEVER allow children to stand, climb or hang on headboard.
ALWAYS anchor headboard to wall or bedframe.
PARENTAL SUPERVISION IS REQUIRED
Parents or Guardians should supervise use under the intended age specifically regarding
children that may have access to it and climb on the unit.
Do not allow horseplay on, under, or behind the unit and prohibit jumping on the unit.
If used improperly, your unit may be pulled over or fall, creating risk of injury or
damage. Children should not be permitted to climb or pull on the headboard.
USE, MAINTENANCE & ASSEMBLY
Periodically check and ensure that the components are in their proper position, free from
damage, and that all connectors are tight.
Use on level surfaces only. Assemble on a soft level surface to avoid damage to unit or floor.
Do not use this item if any components are missing or damaged.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Only clean using damp cloth and mild detergent, do not use bleach or abrasive cleaners.
Check you have all components and tools listed on page 4
Do not stand or put weight on this product during assembly, this could cause damage.
Remove all hardware from the plastic bags and separate them into groups.
Assemble the item as close to its final position (in the same room) as possible.
Certain assembly steps may be easier with 2 people.
Dispose of all packaging carefully and responsibly.
We do not recommend power screwdrivers. Only use hand screwdrivers to prevent
damage to unit.
Keep these instructions for future reference.
Enfants morts suite au basculement d’un meuble.
Afin de limiter le risque de basculement de meuble:
TOUJOURS utiliser les fixations anti-basculement.
NE JAMAIS installer de TV sur ce produit.
NE JAMAIS laisser d’enfants se tenir debout sur les tiroirs,
portes ou etageres, y grimper ou s’y suspendre.
NE JAMAIS ouvrir plus d’un tiroir a la fois.
Han muerto ninos por el vuelco de meubles.
Para limitar el riesgo de vuelco de los meubles:
Utilisar SIEMPRE las fijaciones antivuelco que suministran.
NUNCA instalar un TV sobre este producto.
NUNCA permitar que los ninos se pongan de pie, trepen o
se cuelguen de los cajones, puertas o baldas.
NUNCA abrir mas de un cajon a la vez.
TOUJOURS placer les choses les plus lourdes dans les tiroirs du bas. Colocar los objetos mas pesados en los cajones inferiores.
Page 3 of 9
3
3
1
2
2
ASSEMBLY AT A GLANCE
Please take a moment to read through the whole instruction booklet before assembly to familiarize
yourself with this product. Once you feel ready to start, follow the instructions step by step and this should
make this process as easy as we could make it for you.
This drawing is to give you an overall idea only of how this assembly will go together
and does not replace the assembly instructions.
Page 4 of 9
COMPONENT PARTS
Please check that you have all the parts listed below
1.
Headboard ×1
2.
Leg ×2
3.
Mounting Brackets ×2
ASSEMBLY HARDWARE
M8 ×4
Washer ×4
Nut ×4 Wall Anchors ×4
Screw ×4
Hex Screwdriver
(included)
D
C
A
3
3
1
2
2
B
F
ASSEMBLY
INSTRUCTIONS
Page 5 of 9
2
Remove #2 Legs (x2) bolted
to back of 1
1
1
2
2
Attach #2 Leg (x2) to #1 with
A
A bolt (x4).
1 A
A 2
A
A
A
1
2
ASSEMBLY
INSTRUCTIONS
Page 6 of 9
1
2
A
B
C
(SKIP THIS STEP IF MOUNT-
ING HEADBOARD TO WALL) If
attaching to bedframe, Insert
A bolt into #2 leg and attach
to your bedframe mount on
your bedrails (not included)
with B washer and C Nut.
3
2
2
ASSEMBLY
INSTRUCTIONS
Page 7 of 9
1
1
Steps 1
Steps 2
Measure using paper wall
mount template (included in
the back of instructions) to
mark your holes and ensure
your mounts are even and
level. Drill (tool required -
not included) small pilot
holes and install Dx4 into
the pilot holes with hammer
(tool required - not includ-
ed). Insert E (x2) into each
hole of 3 and tighten with
screwdriver into D wall
anchors. Repeat for other E. .
Hang 1 on the wall.
1
1
3
E
E
D
D
D
D
D
D
ASSEMBLY
INSTRUCTIONS
Page 8 of 9
CONGRATULATIONS, YOUR NAILHEAD HEADBOARD IS COMPLETE!
ASSEMBLY
INSTRUCTIONS
Page 9 of 9
400mm
400mm
400mm 400mm
Back of Assembly
Instructions Folded Paper Template
Make sure your template is level before marking your holes. Use masking tape to
temporarily secure template on wall when ensuring paper is completely flat and
even. Use a level to adjust position. Then press pencil through center of marked
holes on template to mark pilot hole target behind paper. Remove paper template
when satisfied with placementand proceed to Wall Mount Instruction step 1.
400mm
400mm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Naomi Home 99352 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues