GE ZBD6400 Manuel utilisateur

Marque: GE

Modèle: ZBD6400

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Owner’s

Manual

Dishwasher

ZBD6400

ZBD6500

ZBD6600

ZBD6700

ZBD6900

ZBD7000

ZBD7100

2
Consumer Information
Dishwasher
Your new Monogram dishwasher makes an eloquent statement of style, convenience and kitchen
planning flexibility. Whether you chose it for its purity of design, practical features or assiduous
attention to detail—or for all of these reasons—you’ll find that your Monogram dishwasher’s
superior blend of form and function will delight you for years to come.
The information on the following pages will help you operate and maintain your dishwasher
properly.
If you have any other questions, visit our Website at: www.monogram.com
Introduction
Contents
Appliance Registration  . . . . . . . . . . . .3, 31, 32
Care and Cleaning  . . . . . . . . . . . . . . . . .20–23
Consumer Services  . . . . . . . . . . . . . . . . . .3, 28
Model and Serial Number Location  . . . . . . .3
Operating Instructions  . . . . . . . . . . . . . . .8–19
Control Panel and settings for
ZBD6400 and ZBD6500  . . . . . . . . . . . . .8, 9
Control Panel and settings for
ZBD6600  . . . . . . . . . . . . . . . . . . . . . .10, 11
Control Panel and settings for
ZBD6700 and ZBD6900  . . . . . . . . . . .12, 13
Control Panel and settings for
ZBD7000 and ZBD7100  . . . . . . . . . . .14, 15
Clean Sensor  . . . . . . . . . . . . . . . . . . . . . .16
Smart Dry (on some models)  . . . . . . . . .16
Tone Silencing  . . . . . . . . . . . . . . . . . . . . .16
Auto Memory  . . . . . . . . . . . . . . . . . . . . . .16
Child Lockout Mode  . . . . . . . . . . . . . . . .16
Water Temperature  . . . . . . . . . . . . . . . . .17
Rinse Agent  . . . . . . . . . . . . . . . . . . . . . . .17
Detergents  . . . . . . . . . . . . . . . . . . . . . . . .17
Dishwasher Racks  . . . . . . . . . . . . . . . .18, 19
Optional Accessories  . . . . . . . . . . . . . . . . . .23
Problem Solver  . . . . . . . . . . . . . . . . . . . .24–27
Safety Instructions  . . . . . . . . . . . . . . . . . . .4–7
USA Warranty . . . . . . . . . . . . . . . . . . . . . . . .29
Canada Warranty  . . . . . . . . . . . . . . . . . . . . .30

Consumer Information

Dishwasher

Before

using

your

dishwasher

Read this manual carefully. It is intended to

help you operate and maintain your new

dishwasher properly.

Keep it handy for answers to your questions.

If you don’t understand something or need

more help, there is a list of toll-free consumer

service numbers included in the back section

of this manual.

Visit our Website at: www.monogram.com

Write

down the

model &

serial

numbers

You can find the model and serial numbers

at the inside upper left tub flange.

Before sending in this card, please write these

numbers here:

Model Number

Serial Number

Use these numbers in any correspondence or

service calls concerning your dishwasher.

If you received

a damaged

dishwasher

Immediately contact the dealer (or builder)

that sold you the dishwasher.

Save time

& money

Before you request service, check the Problem

Solver in the back of this manual.

It lists causes of minor operating problems that

you can correct yourself.

If you

need service

To obtain service, see the Consumer Services

page in the back of this manual.

We’re proud of our service and want you to be

pleased. If for some reason you are not happy

with the service you receive, here are steps to

follow for further help.

For customers in the USA:

FIRST, contact the people who serviced your

appliance. Explain why you are not pleased.

In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the

details—including your phone number—to:

Manager, Customer Relations

GE Appliances

Appliance Park

Louisville, KY 40225

For customers in Canada:

FIRST, contact the people who serviced your

appliance. Explain why you are not pleased.

In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the

details—including your phone number—to:

Manager, Consumer Relations

Camco Inc.

1 Factory Lane, Suite 310

Moncton, N.B. E1C 9M3

Junked or abandoned dishwashers are

dangerous…even if they will sit for “just a

few days.” If you are getting rid of your old

dishwasher, please follow the instructions below

to help prevent accidents.

Before You Throw Away Your Old Dishwasher:

•Take off the door of the washing compartment

or remove the door latch keeper (as shown).

IMPORTANT SAFETY INSTRUCTIONS

MESURES DE SÉCURITÉ IMPORTANTES

WARNING!

For your safety, the information in this manual

must be followed to minimize the risk of fire,

explosion, electric shock, or to prevent property

damage, personal injury, or loss of life.

•Do not tamper with controls.

•Do not abuse, sit on, or stand on the door or

dish rack of the dishwasher.

•Do not discard a dishwasher without first

removing the door or removing the door latch.

•Do not store or use combustible materials,

gasoline or other flammable vapors and

liquids

in the vicinity of this or any other appliance.

•Do not allow children to play inside, on or with

this appliance or any discarded appliance.

•Do not allow children to play around the

dishwasher when opening and closing the door

due to possibility of small fingers being pinched

in the door.

AVERTISSEMENT

Pour votre sécurité, veuillez suivre à la lettre les

directives données dans le présent manuel afin

de réduire les risques d’incendie, d’explosion ou

de chocs électriques, et prévenir les dommages

matériels et les blessures graves ou mortelles.

• Ne modifiez pas le fonctionnement des

commandes.

• Ne montez pas ou ne vous assoyez pas sur la

porte ou les paniers du lave-vaisselle, et ne les

utilisez pas de façon abusive.

• Ne jetez pas un lave-vaisselle sans en avoir

d’abord enlevé la porte ou enlevez le verrou

de la porte.

• N’entreposez pas et n’utilisez pas d’essence,

de vapeurs ou de liquides inflammables à

proximité de cet appareil ou de tout autre

électroménager.

• Ne laissez pas les enfants jouer avec le lave-

vaisselle ni monter dessus. Ne les laissez pas

s’introduire à l’intérieur de cet appareil ou

d’un vieil appareil qui ne sert plus.

•

Ne permettez jamais à des enfants de jouer à

proximité d’un lave-vaisselle quand vous ouvrez

ou fermez la porte. Ils peuvent se coincer les

doigts dans la porte.

BONNE DISPOSITION DU LAVE-VAISSELLE

Les machines à laver la vaisselle abandonnée

ou jetée sont dangereuses...même si elles sont

abandonnées «juste pendant quelques jours».

Si vous jetez votre vieux lave-vaisselle, veuillez

suivre les instructions suivantes pour prévenir

tout accident.

Avant de jeter votre vieux lave-vaisselle :

•Enlevez la porte du compartiment de lavage

ou enlevez le réceptacle à verrou (comme

l’indique l’illustration).

AVERTISSEMENT! RISQUE D’ENFANT MIS AU PIÈGE

Réceptacle à

verrou

PROPER DISPOSAL OF THE DISHWASHER

WARNING! RISK OF CHILD ENTRAPMENT

Door latch

keeper

WATER HEATER SAFETY

Under certain conditions hydrogen gas may be

produced in a water heater that has not been

used for two weeks or more. HYDROGEN

GAS IS EXPLOSIVE.

If the hot water has not been used for two

weeks or more, prevent the possibility of

damage or injury by turning on all hot water

faucets and allowing them to run for several

minutes. Do this before using any electrical

appliance which is connected to the hot water

system. This simple procedure will allow any

built-up hydrogen gas to escape. Since the gas

is flammable, do not smoke or use an open

flame or appliance during this process.

SÉCURITÉ DU CHAUFFE-EAU

Dans certaines conditions, il peut se former de

l’hydrogène à l’intérieur d’un chauffe-eau qui

n’a pas servi pendant deux semaines ou plus.

L’HYDROGÈNE EST UN GAZ EXPLOSIF.

Pour réduire les risques de dommages ou de

blessures lorsque l’eau chaude n’a pas été

utilisée depuis deux semaines ou plus, ouvrez

tous les robinets d’eau chaude et laissez l’eau

couler pendant plusieurs minutes avant

d’utiliser un appareil électrique raccordé au

système d’eau chaude. Vous éliminerez ainsi

l’hydrogène qui pourrait s’y être accumulé.

Puisqu’il s’agit d’un gaz inflammable, ne fumez

pas ou n’utilisez pas une flamme nue au cours

de ce processus.

IMPORTANT SAFETY INSTRUCTIONS

MESURES DE SÉCURITÉ IMPORTANTES

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and

located in accordance with the Installation

Instructions before it is used. If you did not

receive an Installation Instructions sheet with

your dishwasher, you can receive one by visiting

our Website at www.monogram.com

•Connect to a grounded metal, permanent

wiring system; or run an equipment-

grounding conductor with the circuit

conductors and connect to the equipment-

grounding terminal or lead of the appliance.

•Improper connection of the equipment-

grounding conductor can result in a risk of

electric shock. Check with a qualified

electrician or service representative if you are

in doubt whether the appliance is properly

grounded.

•Dispose of discarded appliances and shipping

or packing material properly.

•Do not attempt to repair or replace any part

of your dishwasher unless it is specifically

recommended in this manual. All other

servicing should be referred to a qualified

technician.

•To minimize the possibility of electric shock,

disconnect this appliance from the power

supply before attempting any maintenance.

NOTE: Turning the dishwasher off does not

disconnect the appliance from the power

supply. We recommend having a qualified

technician service your appliance.

INSTALLATION ET ENTRETIEN APPROPRIÉS

Avant de l’utiliser, vous devez installer

correctement ce lave-vaisselle conformément

aux directives d’installation fournies. Si vous

n’avez pas reçu une feuille de directives

d’installation avec votre lave-vaisselle, vous

pouvez en obtenir un exemplaire par visiter

notre site Web à l’adress www.monogram.com.

• Cet appareil doit être relié à un système de

câblage électrique permanent, mis à la terre.

Sinon, un fil de mise à la terre pour

appareillage doit être installé et raccordé à la

borne ou au fil de mise à la terre de l’appareil.

• Un raccordement non approprié du fil de

mise à la terre pour appareillage peut

présenter des risques de chocs électriques. Si

vous doutez de la qualité de la mise à la terre

de votre électroménager, consultez un

représentant du Service après-vente ou un

électricien qualifié.

• Jetez de la façon appropriée les vieux

électroménagers, ainsi que le matériel

d’emballage et d’expédition.

• Ne tentez pas de réparer ou de remplacer

toute pièce de votre lave-vaisselle, à moins que

cela ne soit spécifiquement recommandé dans

le présent manuel. Confiez toutes les autres

réparations à un réparateur qualifié.

• Afin de réduire les risques de chocs

électriques, débranchez toujours l’appareil

avant de le réparer. REMARQUE : Lorsque

vous mettez la commande du lave-vaisselle à

OFF (arrêt), le courant qui alimente l’appareil

n’est pas coupé. Nous vous recommandons de

confier la réparation de votre appareil à un

réparateur qualifié.

Use this appliance only for its intended

purpose as described in this Owner’s Manual.

CAUTION: Contents washed

in Sanitization cycle may be hot to the

touch. Use care before unloading.

•Use only powder, tabs or liquid detergents

or wetting agents recommended for use in a

dishwasher and keep them out of the reach

of children.

•Locate sharp items so that they are not likely

to damage the door seal.

•Load sharp knives with the handles up to

reduce the risk of cut-type injuries.

•Do not wash plastic items unless marked

dishwasher safe or the equivalent. For

plastic items not so marked, check the

manufacturer’s recommendations.

•Non-Dishware Items: Do not wash items such

as electronic air cleaner filters, furnace filters

and paint brushes in your dishwasher. Damage

to dishwasher and discoloration or staining of

dishwasher may result.

•Do not touch the heating element during or

immediately after use.

•Do not operate your dishwasher unless all

enclosure panels are properly in place.

•Close supervision is necessary if this appliance

is used by or near children.

•Load light plastic items so they will not

become dislodged and drop to the bottom of

the dishwasher—they might come into

contact with the heating element and be

damaged.

WHEN USING YOUR DISHWASHER

READ AND FOLLOW THIS SAFETY

INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

N’utilisez ce lave-vaisselle que pour l’usage auquel

il est destiné, comme expliqué dans le présent

Manuel d’utilisation.

MISE EN GARDE : Les

matériaux lavés selon le cycle anti-bactériel

peuvent être chauds. Faites attention quand

vous videz votre machine.

• N’utilisez que des détergents liquides, en poudre

ou en pastilles et les produits de rinçage

recommandés pour lave-vaisselle. Gardez tous

ces produits hors de portée des enfants.

• Placez les articles aiguisés de manière à ce qu’ils

n’endommagent pas le joint de la porte.

• Placez les couteaux les poignées vers le haut afin

de réduire les risques de coupures.

• Ne lavez pas d’articles en plastique dans le lave-

vaisselle, à moins qu’ils portent la mention

lavable au lave-vaisselle ou toute mention

équivalente. Lorsque les articles de plastique

ne portent aucune mention, lisez les

recommandations du fabricant.

• Articles divers : Ne lavez pas des articles comme

les filtres à air électroniques, les filtres de

fournaise et les pinceaux dans votre lave-

vaisselle. Ils pourraient endommager le lave-

vaisselle et décolorer ou tacher la cuve.

• Ne touchez pas à l’élément chauffant pendant

ou immédiatement après le lavage.

• Ne faites pas fonctionner votre lave-vaisselle

lorsque l’un de ses panneaux est enlevé.

• Il faut exercer une étroite surveillance lorsque

vous faites fonctionner le lave-vaisselle en

présence d’enfants.

• Placez les articles légers en plastique de façon

qu’ils ne bougent pas ou ne tombent au fond de

l’appareil pendant le lavage. Ils pourraient être

endommagés s’ils entrent en contact avec

l’élément chauffant.

LORSQUE VOUS UTILISEZ VOTRE LAVE-VAISSELLE

VEUILLEZ LIRE ET SUIVRE À LA LETTRE

CES MESURES DE SÉCURITÉ.

CONSERVEZ CES DIRECTIVES

Control Panel — ZBD6400 & ZBD6500

Dishwasher

Cycle Selections

1 2 54

ZBD6400 & ZBD6500

Control

Settings

1. Cycle Status This display tells you what is happening while the dishwasher is in operation.

Indicators— All of the Cycle Status Indicators will flash on and off if either the door is

opened during a cycle or if the cycle has been paused. Your wash is complete

when the CLEAN light is illuminated.

SENSING Displayed when the dishwasher is monitoring temperature and water level

during fill and drain. Also displayed during periods using CleanSensor

technology. CleanSensor measures the amount of soil in the load and decides

if a more rigorous wash cycle is required.

WASHING Displayed during the prewash and main wash periods.

RINSING Displayed during rinse periods.

DRYING Displayed during the dry period (if HEATED DRY is selected).

CLEAN Displayed when cycle is complete. Light remains ON until the door is opened.

2. Cycle Selections—The light on the selected pad will illuminate to indicate which cycle has been

selected.

POTS & PANS For heavily soiled dishes or cookware with dried-on or baked-on soils.

Everyday dishes may be included. This cycle may not remove burned-on foods.

NORMAL For loads of everyday dishes, glasses and cookware with medium soils.

WASH NOTE: For heavily soiled dishes, choose NORMAL WASH plus HIGH water

temperature option.

CHINA For lightly soiled china and crystal, or recently used, lightly soiled dishes

CRYSTAL and glassware to be washed in a short time, at moderate temperatures up

to 125°F (51°C).

SANI WASH Provides a sanitizing wash and rinse with water temperatures up to 160°F

(71°C). The SANI WASH light will remain illuminated at the end of the cycle

to indicate that sanitization conditions have been met.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

You can locate

your model

number on the

inside upper tub

flange.

Throughout this

manual, features

and appearance

may vary from

your model.

NSF INTERNATIONAL

Meets NSF Standard 184 Sanitization and Cleaning performance

of household spray-type dishwashers.

3. HEATED DRY— When selected, turns the drying heater and fan on for fast drying. This option

will extend the cycle by 30 minutes. When this is NOT selected, the fan will

turn on to dry your dishes without added heat—and energy is saved.

HEATED DRY is not available on RINSE ONLY.

4. WATER TEMP— This button provides extra heat options to increase water temperature for

optimum performance.

NORMAL This is the default setting—provides a wash and rinse with water temperatures

up to 131°F (55°C) in the NORMAL cycle and 145°F (63°C) in POTS &

PANS.

HIGH This water temp selection provides a wash and rinse with water temperatures

up to 135°F (57°C) in the NORMAL cycle and 155°F (68°C) in POTS &

PANS. Use this option for heavily soiled dishes. Cannot be used with RINSE

ONLY or CHINA CRYSTAL.

5. DELAY START—This option will allow you to delay the start time of any wash cycle except

RINSE ONLY for up to 6 hours.

• Select the delay start time you want by pressing the DELAY START button. Multiple pressing

will alternate the delay time between 2, 4 or 6 hours and OFF.

Start a

wash load

To start the dishwasher, close the door until it locks in place. The last used cycle will be displayed.

To begin this cycle, push the START button. To select a different cycle, push the desired Cycle

Selection and Option buttons, and then press the START button.

The door must be closed and latched into place to select a cycle or an option.

To interrupt/pause a cycle, press the selected cycle button. The Status Indicators will flash.

CAUTION: Be careful when opening the door; the hot steam that escapes when the door is

opened may cause injuries. Stand back as you open the door and allow the steam to

escape.

ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui s’échappe

lorsque vous ouvrez la porte pendant un programme de lavage peut causer des

brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur s’échapper de

l’appareil.

To restart the wash process, close the door until it locks in place. Re-press the cycle button. There

may be a time delay of up to a few minutes, because the temperature inside the dishwasher needs to

stabilize before it starts the wash cycle. During this time the SENSING light will be on.

To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.

The dishwasher will then drain and the cycle indicator lights will flash. At this point a new wash cycle

can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out after the

dishwasher drains. If you have selected a new wash cycle, remember to add more detergent to

the detergent compartment if required.

Control Panel/Operation — ZBD6400 & ZBD6500

Dishwasher

Control Panel — ZBD6600

Dishwasher

1 2

Control

Settings

1. WASH CYCLES Knob—Use to select the desired wash cycle based on dishware and soil level.

POTS & PANS For heavily-soiled dishes or cookware with dried-on or baked-on soils.

Everyday dishes may be included. This cycle may not remove burned-on foods.

NORMAL For loads of everyday dishes, glasses and cookware with medium soils.

WASH NOTE: For heavily soiled dishes, choose NORMAL WASH plus HIGH TEMP

water temperature option.

CHINA For lightly soiled china and crystal, or recently used, lightly soiled dishes

CRYSTAL and glassware to be washed in a short time at moderate temperatures up to

125°F (51°C).

SPEED WASH For recently used, lightly soiled dishes and glassware to be washed in a short

time. Provides a wash and rinse with water temperatures up to 125°F (51°C).

RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent

with this cycle.

2. HEAT OPTIONS Knob—Use to select water temperature and drying options.

NORMAL Provides a wash and rinse with water temperatures up to 131°F (55°C) in the

NORMAL cycle and 145°F (63°C) in POTS & PANS.

HIGH TEMP Provides a wash and rinse with water temperatures up to 135°F (57°C) in the

NORMAL cycle and 155°F (68°C) in POTS & PANS. Not available for SPEED

WASH, CHINA CRYSTAL or RINSE ONLY cycles.

SANITIZE Provides a sanitizing wash and rinse with water temperatures up to 160°F

(71°C) in the NORMAL cycle and 171°F (77°C) in POTS & PANS.

Not available for SPEED WASH, CHINA CRYSTAL or RINSE ONLY cycles.

At the end of the cycle, the HEAT OPTIONS light will illuminate to indicate

that the sanitization conditions have been met. The sanitize heat option

includes HEAT DRY.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

HEAT DRY When selected, turns the drying heater on for fast drying. This option will

extend the cycle by 30 minutes. When this option is NOT selected, energy

is saved. HEAT DRY is not available on RINSE ONLY.

ZBD6600You can locate

your model

number on the

inside upper tub

flange.

Throughout this

manual, features

and appearance

may vary from

your model.

NSF INTERNATIONAL

Meets NSF Standard 184 Sanitization and Cleaning performance of

household spray-type dishwashers.

Operation — ZBD6600

Dishwasher

To interrupt/pause a cycle gently open the door just enough to turn off the wash motor. Do not

fully open the door until the wash action ceases.

CAUTION: Be careful when opening the door; the hot steam that escapes when the door is

opened may cause injuries. Stand back as you open the door and allow the steam

to escape.

ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui

s’échappe lorsque vous ouvrez la porte pendant un programme de lavage peut

causer des brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur

s’échapper de l’appareil.

To restart the wash process, close the door until it locks in place. There may be a time delay of

up to a few minutes because the temperature inside your dishwasher needs to stabilize before it

restarts the wash cycle.

To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.

The dishwasher will start to drain and the cycle indicator lights will flash. At this point a new wash

cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out after

the dishwasher drains completely. If you have selected a new wash cycle, remember to add more

detergent to the detergent compartment if required.

NORMAL

& HEAT

DRY

SANITIZE

(INCLUDES

HEATED

DRY)

POTS & PANS

NORMAL WASH

CHINA CRYSTAL

SPEED WASH

RINSE ONLY

Wash Cycles

✓

—

To start the dishwasher, close the door until it locks in place. To start the last selected cycle, press

the START button. To select a different cycle, turn the knobs to the desired WASH CYCLE and

HEAT OPTIONS and press the START button.

NOTE: Not all heat options are available for all cycles. If a combination that is not available is

selected, the lights will flash when the START button is pressed and the cycle will not start.

HEAT OPTIONS

HIGH

TEMP &

HEAT DRY

HIGH

TEMP

✓

—

✓

—

✓

—

Start a

wash load

Control Panel — ZBD6700 & ZBD6900

Dishwasher

Cycle Selections

ZBD6700 & ZBD6900

Control

Settings

1. Cycle Status This display tells you what is happening while the dishwasher is in operation.

Indicators— All of the Cycle Status Indicators will flash on and off if either the door is

opened during a cycle or if the cycle has been paused. Your wash is complete

when the CLEAN light is illuminated.

SENSING Displayed when the dishwasher is monitoring temperature and water level

during fill and drain. Also displayed during periods using CleanSensor

technology. CleanSensor measures the amount of soil in the load and decides

if a more rigorous wash cycle is required.

WASHING Displayed during the prewash and main wash periods.

RINSING Displayed during rinse periods.

DRYING Displayed during the dry period (if SMART DRY is selected).

CLEAN Displayed when cycle is complete. Light remains ON until the door is opened.

2. Cycle Selections—The light on the selected pad will illuminate to indicate which cycle has been

selected.

POTS & PANS For heavily soiled dishes or cookware with dried-on or baked-on soils.

Everyday dishes may be included. This cycle may not remove burned-on foods.

NORMAL For loads of everyday dishes, glasses and cookware with medium soils.

WASH NOTE: For heavily soiled dishes, choose NORMAL WASH plus HIGH water

temperature option.

CHINA For lightly soiled china and crystal, or recently used, lightly soiled dishes

CRYSTAL and glassware to be washed in a short time, at moderate temperatures up to

125°F (51°C).

RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent with

this cycle

1 2 543

You can locate

your model

number on the

inside upper tub

flange.

Throughout this

manual, features

and appearance

may vary from

your model.

3. SMART DRY— When selected, sensors detect the presence of rinse aid and the final rinse

temperature. The drying heater and fan are then turned on for the minimum

time to achieve optimum drying results. This saves energy as compared to

conventional heated dry and saves time as compared to non-heated dry.

SMART DRY is not available on RINSE ONLY.

4. WATER TEMP— This button provides extra heat options to increase water temperature for

optimum performance.

NORMAL This is the default setting—provides a wash and rinse with water temperatures

up to 131°F (55°C) in the NORMAL cycle and 145°F (63°C) in POTS &

PANS.

HIGH This water temp selection provides a wash and rinse with water temperatures

up to 135°F (57°C) in the NORMAL cycle and 155°F (68°C) in POTS &

PANS. Use this option for heavily soiled dishes. Cannot be used with RINSE

ONLY or CHINA CRYSTAL.

SANI This water temp selection provides a sanitizing wash and rinse with water

temperatures up to 160°F (71°C) in the NORMAL cycle and 171°F (77°C) in

POTS & PANS. Cannot be used with RINSE ONLY or CHINA CRYSTAL. At

the end of the WASH cycle, the SANI OPTION light will remain illuminated

to indicate that the sanitization conditions have been met.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

5. DELAY START—This option will allow you to delay the start time of any wash cycle except

RINSE ONLY for up to 6 hours.

• Select the delay start time you want by pressing the DELAY START button. Multiple pressing

will alternate the delay time between 2, 4 or 6 hours and OFF.

Start a

wash load

To start the dishwasher, close the door until it locks in place. The last used cycle will be displayed. To

begin this cycle, push the START button. To select a different cycle, push the desired Cycle Selection

and Option buttons, and then press the START button.

The door must be closed and latched into place to select a cycle or an option.

To interrupt/pause a cycle, press the selected cycle button. The Status Indicators will flash.

CAUTION: Be careful when opening the door; the hot steam that escapes when the door is

opened may cause injuries. Stand back as you open the door and allow the steam

to escape.

ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui s’échappe

lorsque vous ouvrez la porte pendant un programme de lavage peut causer des

brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur s’échapper

de l’appareil.

To restart the wash process, close the door until it locks in place. Re-press the cycle button. There

may be a time delay of up to a few minutes, because the temperature inside the dishwasher needs

to stabilize before it restarts the wash cycle. During this time the SENSING light will be on.

To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.

The dishwasher will then drain and the cycle indicator lights will flash. At this point a new wash

cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out after

the dishwasher drains. If you have selected a new wash cycle, remember to add more detergent

to the detergent compartment if required.

Control Panel/Operation — ZBD6700 & ZBD6900

Dishwasher

NSF INTERNATIONAL

Meets NSF Standard 184 Sanitization and Cleaning performance

of household spray-type dishwashers.

Control Panel — ZBD7000 & ZBD7100

Dishwasher

ZBD7000 & ZBD7100

Control

Settings

1. Cycle Selections—The light on the selected pad will illuminate to indicate which cycle has been

selected.

POTS & PANS For heavily-soiled dishes or cookware with dried-on or baked-on soils.

Everyday dishes may be included. This cycle may not remove burned-on foods.

NORMAL For loads of everyday dishes, glasses and cookware with medium soils.

WASH NOTE: For heavily soiled dishes, choose NORMAL WASH plus HIGH water

temperature option.

CHINA For lightly soiled china and crystal, or recently used, lightly soiled dishes

CRYSTAL and glassware to be washed in a short time at moderate temperatures up to

125°F (51°C).

RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent with

this cycle.

2. WATER TEMP— This button provides extra heat options to increase water temperature for

optimum performance.

NORMAL This is the default setting—provides a wash and rinse with water temperatures

up to 131°F (55°C) in the NORMAL cycle and 145°F (63°C) in POTS &

PANS.

HIGH This water temp selection provides a wash and rinse with water temperatures

up to 135°F (57°C) in the NORMAL cycle and 155°F (68°C) POTS & PANS.

SANITIZE This water temp selection provides a sanitizing wash and rinse with water

temperatures up to 160°F (71°C) in the NORMAL cycle and 171°F (77°C) in

POTS & PANS. This selection cannot be used with RINSE ONLY or CHINA

CRYSTAL. At the end of the wash cycle, the SANITIZE OPTION light will

remain illuminated to indicate that the sanitization conditions have been met.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

3. SMART DRY—When selected, sensors detect the presence of rinse aid and the final rinse

temperature. The drying heater and fan are then turned on for the minimum

time to achieve optimum drying results. This saves energy as compared to

conventional heated dry and saves time as compared to non-heated dry.

SMART DRY is not available on RINSE ONLY.

1 3 42

You can locate

your model

number on the

inside upper tub

flange.

Throughout this

manual, features

and appearance

may vary from

your model.

NSF INTERNATIONAL

Meets NSF Standard 184 Sanitization and Cleaning performance

of household spray-type dishwashers.

To start the dishwasher, open the dishwasher door so that the top-of-door controls are visible. The

last used cycle will be displayed. To begin this cycle, press the START button. To select a different

cycle, press the desired Cycle Selection and Option buttons, and then press the START button.

After the door is closed and latched, the selected cycle will begin.

To interrupt/pause a cycle, gently open the door just enough to turn off the wash motor. Do not

fully open the door until the wash action ceases.

WARNING: Do not fully open door while the dishwasher is in operation. Quickly opening the

door while the dishwasher is operating could result in serious scalding. Be careful

when opening the door; the hot steam that escapes when the door is opened may

cause injuries. Stand back as you open the door and allow the steam to escape.

AVERTISSEMENT : N’ouvrez pas complètement la porte lorsque la laveuse fonctionne. Une

ouverture rapide de la porte lorsque l’appareil est en fonctionnement

peut entraîner de sérieuses brûlures. Faites attention lorsque vous ouvrez

la porte; la vapeur brûlante qui s’échappe lors de l’ouverture de la porte

peut causer des blessures. Tenez vous en arrière lorsque vous ouvrez la

porte afin de permettre à la vapeur de s’échapper.

To restart the wash process, close the door until it locks in place. There may be a time delay of

up to a few minutes because the temperature inside the dishwasher needs to stabilize before it

restarts the wash cycle.

To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.

The dishwasher will then drain and the cycle indicator lights will flash. At this point a new wash

cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out after

the dishwasher drains. If you have selected a new wash cycle, remember to add more detergent to

the detergent compartment if required.

Start a

Wash Load

Control Panel/Operation — ZBD7000 & ZBD7100

Dishwasher

Control

Settings

4. DELAY START—This option will allow you to delay the start time of any wash cycle except

RINSE ONLY for up to 6 hours.

• Select the delay start time you want by pressing the DELAY START button. Multiple pressing

will alternate the delay time between 2, 4 or 6 hours and OFF.

Features — ZBD6400, ZBD6500, ZBD6700, ZBD6900, ZBD7000 & ZBD7100

Dishwasher

Auto

Memory

Your dishwasher has the ability to remember what options you like with NORMAL WASH and

POTS & PANS wash cycle. This means that if you select NORMAL WASH your dishwasher will

automatically select the options that you selected last time you washed with the NORMAL WASH

cycle. You can change the options that have been remembered with a particular wash cycle if you

desire.

Child

Lockout

Mode

(on some

models)

To reduce the possibility of children starting the dishwasher when unattended, a child lockout

feature can be enabled. Once enabled, each button must be pressed and held for two seconds until

you hear a BEEP, before the dishwasher will respond. While in this mode the SENSING and

CLEAN light will illuminate while the button is pressed.

This feature can be enabled by pressing both the START/CANCEL and POTS & PANS buttons

together and holding both for two seconds. You will hear three BEEPS when the child lockout is

enabled.

The child lockout can be cancelled by pressing the START/CANCEL and POTS & PANS together

and holding both pressed for two seconds until a single BEEP is heard.

NOTE: Child lockout overrides tone silencing.

Tone

Silencing

(on some

models)

You can prevent the beep from sounding when selecting control settings.

1. Press the START/CANCEL and NORMAL WASH buttons together prior to selecting settings.

2. To have sound again, simply press the START/CANCEL and NORMAL WASH buttons

together again.

Clean

Sensor

The Clean Sensor monitors the circulating water during the cycles and sets the water temperature

and cycle length to match soil levels. Cycle length is automatically increased to handle increasing

levels of soil.

Detergent

Usage

Guide

(Powder or

Liquid)

SOFT WATER MEDIUM WATER HARD WATER

0–3 grains 3–7 grains 7–12 grains*

CYCLES Main Cup Auxiliary Cup Main Cup Auxiliary Cup Main Cup Auxiliary Cup

POTS & PANS Full None Full Full Full Full

NORMAL WASH

⁄2 Full None Full None Full Full

CHINA CRYSTAL

⁄2 Full None Full None Full Full

SPEED WASH

⁄2 Full None Full None Full Full

RINSE & HOLD Use no detergent Use no detergent Use no detergent

*12 grains and up is extremely hard water. A water softener

is recommended. Without it, lime can build up in the

water valve. The water valve may stick and flooding could

occur.

NOTE: The above chart is a general guide. Detergent

amounts should be adjusted depending on the amount

and type of soil until satisfactory results are achieved.

APPROXIMATE CYCLE TIME*

With 120°F Water

TEMPERATURE (°F) (excluding drying time)

CYCLES Normal High Sani Normal High Sani

POTS AND PANS 145 155 171 6.2–7.4 80 85 102

NORMAL 131 135 160 5.0–11.2 72 75 89

CHINA CRYSTAL 125 — — 5.0 31 — —

RINSE ONLY — — — 1.2 11 — —

SPEED WASH 115–125 — — 3.8 22 — —

SANI WASH 160 — — 6.2 89 — —

(on some models)

Cycle Chart

WATER USAGE

(Gallons)

*Cycle length will vary based on water temperature option and soil level present.

Use only detergent specifically made for use

in dishwashers. Keep your powdered detergent

fresh

and dry. Don’t put powder detergent into

the

dispenser until you’re ready to wash dishes.

The amount of detergent to use depends on

whether your water is hard or soft. With hard

water, you need extra detergent. With soft

water, you need less detergent.

Protect your dishes and dishwasher by

contacting your water department and asking

how hard your water is. Twelve or more

grains

is extremely hard water. A water softener is

recommended.

Without it, lime can build up

in the water valve, which could stick while open

and cause flooding. Too much detergent with

soft water can cause a permanent cloudiness of

glassware, called etching.

To open the detergent compartment, push the

lever latch inward.

When using automatic dishwashing detergent

tabs, place one tab in the main cup and close.

Be sure the Cycle Status Indicators (on some

models) are not lit before adding detergent.

Otherwise, the detergent cup will not close and

latch properly. Add detergent then close the

main cup.

NOTE: To open detergent cup after it has been

closed, push the lever latch inward.

Lever

Main compartment

Using the dishwasher

Dishwasher

Detergents

Water

Temperature

The entering water must be at least 120°F

(49°C) and

not more than 150°F (66°C), for

effective cleaning and to prevent dish damage.

Check the water temperature with a candy or

meat thermometer. Turn on the hot water faucet

nearest the dishwasher, place the thermometer

in a glass and let the water run continuously into

the glass until the temperature stops rising.

Use a

Rinse

Agent

A rinse agent improves dry performance,

reduces spots and prevents new film build-up

on your dishes, glasses, flatware, cookware

and plastic.

Fill the rinse agent chamber by rotating the

round cap counterclockwise and remove. Fill

chamber to maximum level. Replace and lock

the cap into place.

To check if rinse agent is needed: a solid black

indicator indicates sufficient rinse agent; a clear

indicator indicates a low level and requires

adding more rinse agent.

•A full dispenser should last about one month.

•If rinse agent spills, wipe it up immediately.

It can keep your detergent from working.

•

If after washing you notice cloudy spots,

streaks or water marks on the glassware, and

the rinse agent dispenser is not empty, it may

be necessary to increase the dispenser settings.

To do so, remove the cap and using a butter

knife, rotate the indicator arrow to a higher

number. Replace the cap when done.

•

If glasses appear smeared or there is foam

present on the bottom of the glasses or the

bottom of the machine, select a lower dosage

number.

•

For softened water, reduce dispenser setting.

Light level Indicator

Adjust to higher or lower number

Auxiliary

compartment

Loading the Racks

Dishwasher

Upper Rack

The upper rack is for glasses, cups, bowls and saucers.

Cups and glasses fit best along the sides. This is also a

secure place for dishwasher-safe plastics.

The cup shelf may be placed in the up or down

position to add flexibility. The cup shelf can also secure

wine glasses at an angle for best washability. Because

wine glasses come in various sizes, after loading, slowly

push in the rack to make sure they will clear the top of

the dishwasher.

The upper rack is good for all kinds of oddly-shaped

utensils. Saucepans, mixing bowls and other items

should be placed face down.

Secure larger dishwasher-safe plastic items over two

fingers when possible.

Fold-down tines (on some models) provide flexibility

for extra-large and hard-to-fit items.

Make sure small plastic items are secure so they can’t

fall onto the heating element.

Upper

Wash

Tower

Take care not to obstruct the rotation of the

spray arm under the upper rack or cover the

water collector in the center of the upper rack.

Fold-down cup rack

can support extra cup

Fold-down cup rack can

support glass stems

Squeeze

Re-adjust

upper rack

Adjusting

Upper Rack

Height

The upper rack can be raised or lowered to

provide extra room for different sized items.

Empty the upper rack. Remove the rail pegs

in the front of the rack runners by squeezing

and lifting the top of the peg, then slide the

rack out.

Re-insert the rack in the chosen position and

replace the pegs. Check that the spray arm is

free to rotate.

Lift peg from rack

runner

these

guidelines

for loading

10 place

settings

Lower Rack

When loading the lower rack, do not load large platters

or trays in the front left corner. They may prevent

detergent from circulating during the wash cycle.

The lower rack is best used for plates, saucers, and

cookware. Large items such as broiler pans and

racks should go along the sides. Load platters, pots

and bowls along the sides, in corners, or in the back.

The soiled side of items should face the center of

the rack.

Fold-down fingers provide flexibility for extra large

and hard-to-fit items.

The fingers may be left in the up position or folded

down to customize the lower rack.

Silverware

Basket

Put flatware in the removable basket with fork and knife handles up to protect your hands. Place

spoons in the basket with handles down. Mix knives, forks and spoons so they don’t nest together.

Distribute evenly. Small plastic items, such as measuring spoons and lids from small containers,

should go in the bottom of the silverware basket with silverware on top.

Flip-down covers can be lowered to secure lightweight items from the effects of the vigorous wash

action. The slots in the covers can be used to separate silverware.

Don’t let any item

extend through bottom

Flip-down covers can

be lowered to secure

lightweight items

Features and appearance of racks and silverware baskets may vary from your model.

Care and Cleaning

Dishwasher

Exterior

To clean the control panel use a lightly dampened cloth then dry thoroughly. To clean the

exterior painted panels use a good appliance polish wax.

Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.

Use stainless steel cleaner on stainless steel panel. You can order

Stainless Steel Magic # WX10X15

through GE Parts in the USA, by calling 800.626.2002. In Canada, call 1.888.880.3030.

Protect

Against

Freezing

If your dishwasher is left in an unheated place during the winter, ask a service technician to:

1. Cut off electrical power to the dishwasher. Remove fuses or trip circuit breaker.

2. Turn off the water supply and disconnect the water inlet line from the water valve.

3. Drain water from the water inlet line and water valve. (Use a pan to catch the water.)

4. Reconnect the water inlet line to the water valve.

5. Remove the filters from the tub bottom and use a sponge to soak up water.

The Air

Gap

An air gap protects your dishwasher against

water backing up into it if a drain clogs. The air

gap is not a part of the dishwasher. It is not

covered by your warranty. Not all plumbing

codes require air gaps, so you may not have one.

The air gap is easy to clean.

1. Turn off the dishwasher and lift off the

chrome cover.

2. Unscrew the plastic cap and clean with

a toothpick.

Interior

The stainless steel tub can be cleaned with Stainless Steel Magic or a similar product using

a clean, soft cloth.

Use stainless steel cleaner on stainless steel panel. You can order

Stainless Steel Magic # WX10X15

through GE Parts in the USA, by calling 800.626.2002. In Canada, call 1.888.880.3030.

Wipe the rubber door seals occasionally, including the seal at the bottom of the door.

Check the air gap any time your dishwasher

isn’t draining well.

Two types of

air gaps

La page est en cours de chargement...

GE ZBD6400 Manuel utilisateur

Marque: GE

Modèle: ZBD6400

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: GE ZBD6400 User manual

GE ZBD6400 Manuel utilisateur

GE ZBD6400 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents