Clarke BOOST 28 Manuel utilisateur

Form No. 71071A 3/06 Clarke

®

Printed in the U.S.A.

U.S. Patent No. 6,105,192; No. 6,557,207; No. 6,760,947; No. 5,383,251; & Patents Pending

This book has important information for the use and safe operation of this machine. Failure to read this

book prior to operating or attempting any service or maintenance procedure to your Clarke machine

could result in injury to you or to other personnel; damage to the machine or to other property could occur

as well. You must have training in the operation of this machine before using it. If your operator(s) cannot

read this manual, have it explained fully before attempting to operate this machine.

All directions given in this book are as seen from the operator’s position at the rear of the machine.

For new books write to: Clarke

®

, 2100 Highway 265, Springdale, Arkansas 72764.

English (2 - 27)

Español (28 - 53)

Français (54 - 79)

READ THIS BOOK

LEA ESTE MANUAL

LISEZ CE MANUEL

ES

EN

FR

Operator's Manual

Manuel d'utilisation

Libro de Instrucciones

EN

ENGLISH

-2- Clarke

®

Operator's Manual (EN) - BOOST 28

Table of Contents

SECTION II - Parts and Service Manual

Final Assembly Drawing .................................................................................................................................. 80

Parts List ............................................................................................................................................ 81

Recovery Tank Drawing ................................................................................................................................... 82

Parts List ............................................................................................................................................ 83

Solution Tank Assembly Drawing.................................................................................................................... 84

Parts List ............................................................................................................................................ 85

Rear Panel Assembly Drawing (Remote Charger)......................................................................................... 86

Parts List ............................................................................................................................................ 87

Rear Panel Assembly Drawing (On-Board Charger) ...................................................................................... 88

Parts List ............................................................................................................................................ 89

Control Panel Assembly Drawing.................................................................................................................... 90

Parts List ............................................................................................................................................ 91

Squeegee Lift Assembly Drawing ................................................................................................................... 92

Parts List ............................................................................................................................................ 93

Squeegee Assembly Drawing ......................................................................................................................... 94

Parts List ............................................................................................................................................ 95

Frame Axle Assembly Drawing ........................................................................................................................ 96

Parts List ............................................................................................................................................ 97

Brush Head Assembly Drawing ...................................................................................................................... 98

Parts List ............................................................................................................................................ 99

Optional Brake Assembly Drawing and Parts List .......................................................................................... 100

Vacuum Motor Drawing and Parts List ............................................................................................................ 101

Transaxle Repair Parts .................................................................................................................................... 102

Battery Charger Drawing and Parts List .......................................................................................................... 103

Connection Diagram ........................................................................................................................................ 104

Electrical Schematic......................................................................................................................................... 105

Operator Safety Instructions ............................................................................................................................ 3

Introduction & Machine Specifications ............................................................................................................. 5

Procedures for Transporting Machine ............................................................................................................. 6

Symbols Used on Boost 28 ............................................................................................................................. 8

Machine Control Panel ..................................................................................................................................... 9

Machine Controls and Features ...................................................................................................................... 10

How to Prepare the Machine for Operation...................................................................................................... 11

How to Install the Batteries ................................................................................................................ 11

Battery Maintenance........................................................................................................................... 12

How to Charge the Batteries (Remote Charger)............................................................................... 13

How to Charge the Batteries (On-Board Charger) ............................................................................ 14

How to Install the Brush or Pad ......................................................................................................... 15

How to Remove the Brush or Pad ..................................................................................................... 15

How to Operate the Machine ............................................................................................................................ 16

How to Operate the Squeegee .......................................................................................................... 16

Filling the Solution Tank .................................................................................................................... 16

Operating the Machine....................................................................................................................... 17

How to Clean a Floor ......................................................................................................................... 18

Maintenance ..................................................................................................................................................... 19

Procedures Before Work is Began .................................................................................................... 19

Procedures to Perform at the End of Work ........................................................................................20

Procedures to Perform Every Week................................................................................................... 21

Maintenance for the Squeegee.......................................................................................................... 22

How to Adjust the Squeegee ............................................................................................................. 22

How to Center or Off set Brushhead ................................................................................................. 23

Accessories...................................................................................................................................................... 24

How to Correct Problems in the Machine ........................................................................................................ 25

EN

ENGLISH

Clarke

®

Operator's Manual (EN) - BOOST 28 - 3 -

DANGER: Failure to read and observe all DANGER statements could result in

severe bodily injury or death. Read and observe all DANGER

statements found in your Owner's Manual and on your machine.

WARNING: Failure to read and observe all WARNING statements could result

in injury to you or to other personnel; property damage could

occur as well. Read and observe all WARNING statements found in

your Owner's Manual and on your machine.

CAUTION: Failure to read and observe all CAUTION statements could result in

damage to the machine or to other property. Read and observe all

CAUTION statements found in our Owner's Manual and on your

machine.

DANGER: Failure to read the Owner's Manual prior to operating or attempting any service or

maintenance procedure to your Clarke machine could result in injury to you or to

other personnel; damage to the machine or to other property could occur as well.

You must have training in the operation of this machine before using it. If you or

your operator(s) cannot read this manual, have it explained fully before attempting

to operate this machine.

DANGER: Operating a machine that is not completely or fully assembled could result in injury

or property damage. Do not operate this machine unless it is completely

assembled. Inspect the machine carefully before operation.

DANGER: Machines can cause an explosion when operated near flammable materials and

vapors. Do not use this machine with or near fuels, grain dust, solvents, thinners,

or other flammable materials. This machine is not suitable for picking up hazardous

dust. Use only commercially available floor cleaning waxes intended for machine

operation.

DANGER: Lead acid batteries generate gases which can cause an explosion. Keep sparks

and flames away from batteries. Do not smoke around the machine. Charge the

batteries only in an area with good ventilation. Make sure that the AC charger plug

is unplugged from the wall receptacle before connecting or disconnecting the DC

plug to or from the battery pack.

DANGER: Working with batteries can be dangerous! Always wear eye protection and

protective clothing when working near batteries. Remove all jewelry. Do not put

tools or other metal objects across the battery terminals, or the tops of the

batteries.

DANGER: Using a charger with a damaged power cord could result in an electrocution. Do

not use the charger if the power cord is damaged.

WARNING: Operating this machine from anywhere other than the back of the machine could result in

injury or damage. Operate this machine only from the rear.

WARNING: This machine is heavy. Get assistance before attempting to transport or move it. Use

two able persons to move the machine on a ramp or incline. Always move slowly. Do

not turn the machine on a ramp. Do not use on surfaces having a gradient exceeding that

marked on the appliance. Read the "Procedures For Transporting" in this manual before

transporting as machine might topple over if not secured.

WARNING: Machines can topple over and cause injury or damage if guided over the edges of stairs or

loading docks. Stop and leave this machine only on a level surface. When you stop the

machine, put all switches into their "OFF" position. Turn the key switch "OFF" and

remove the key.

OPERATOR SAFETY INSTRUCTIONS

EN

ENGLISH

-4- Clarke

®

Operator's Manual (EN) - BOOST 28

WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or

injury. Maintenance and repairs must be performed by authorized Clarke personnel

only.

WARNING: Any alterations or modifications of this machine could result in damage to the machine or

injury to the operator or other bystanders. Alterations or modifications not authorized by

the manufacturer voids any and all warranties and liabilities.

WARNING: Electrical components of this machine can "short-out" if exposed to water or moisture.

Keep the electrical components of the machine dry. Wipe the machine down after each

use. This appliance is for dry use only and is not to be used or stored outdoors in wet

conditions.

WARNING: Operating a machine without observing all labels and instructional information could result

in injury or damage. Read all machine labels before attempting to operate. Make sure all

of the labels and instructional information are attached or fastened to the machine. Get

replacement labels and decals from your Clarke distributor.

WARNING: Wet floor surfaces can be slippery. Water solutions or cleaning materials used with this

type of machine can leave wet areas on the floor surface. These areas can cause a

dangerous condition for the operator or other persons. Always put "Caution" signs

around/near the area you are cleaning.

WARNING: Improper discharge of waste water may damage the environment and be illegal.

The United States Environmental Protection Agency has established certain regulations

regarding discharge of waste water. City, state and national regulations regarding this

discharge may also be in effect in your area. Understand and follow the regulations in

your area. Be aware of the environment hazards of chemicals that you dispose.

WARNING: Only use the brushes provided with the appliance or those specified in the Operator's

Manual. The use of other brushes may impair safety.

CAUTION: Use of this machine to move other objects or to climb on could result in injury or damage.

Do not use this machine as a step or furniture. Do not ride on this machine.

CAUTION: Your machine warranty will be voided if anything other than genuine Clarke parts are

used on your machine. Always use Clarke parts for replacement.

CAUTION: This machine contains lead acid batteries. The batteries must be disposed of in an

environmentally acceptable manner.

EN

ENGLISH

Clarke

®

Operator's Manual (EN) - BOOST 28 - 5 -

SPECIFICATIONS:

Model BOOST 28

Machine Power Supply 24 Volt D.C.,

(4) 6V 250 AH Deep Cycle Batteries or

(4) 6V 330 AH Deep Cycle Batteries

Pad or Brush 1 per Machine

Traverse 0.5 hp (0.4 kW) Transaxle

Traverse Forward Speed Variable to 250 ft./min (76 m/min)

Traverse Reverse Speed Variable to 190 ft./min. (58 m/min)

Battery Protection Low Voltage

Motor Vacuum 3/4 HP, 3 stage, Acoustical High Efficient Tangential

Solution Tank 20 Gallons (76 liters)

Solution Level Calibrated level indicator on rear of machine

Recovery Tank 20 Gallons (76 liters)

Recovery Full Indicator Electric Shut-Off

Parabolic Squeegee Swing type with breakaway feature, No tool operation feature

39 inches (99 cm) hard width with 41 inches (104 cm) flex blade width.

Squeegee Operation Reverse direction on floor and 3 - position manual lever style operation

Cleaning Swath 28 inches (71 cm)

Motor, Brush 3/4 hp (0.56 KW)

Brush / Pad Size 14" x 28" (35.6 cm x 71 cm)

Brush Speed 2250 RPM

Brush Pressure 100 lbs. (45.4 kg)

Drive Wheels (2) 8 in. x 2 in. (20 cm x 5 cm) Neoprene tread

Caster Dual 4 in. x 2 in. (10 cm x 5 cm)

Charger 24 V D.C., 25 Amp, 115/60, on-board optional

Grade Cleaning 5 Degree (6%)

Length 56.25 inches (143 cm)

Width 28.75 inches (73 cm)

Height 43 inches (109 cm)

Weight w/batteries (250 AH) 586 lbs. (266 kg)

Line of Sight (from Operator

Height): 68 inches (173 cm) 7.5 feet (2.3 m)

Noise 71 dBA

Vibration < 2.5 m/s

2

Introduction & Machine Specifications

Clarke’s newly designed BOOST 28 automatic scrubber is an efficient and superior floor cleaning

machine. The BOOST 28 uses an orbital movement to scrub a path 28 inches wide. A squeegee wipes

the floor while the vacuum motor removes the dirty solution from the floor - all in one pass.

The BOOST 28 comes complete with four - 6 volt batteries, one battery charger, a brush or a pad, and

one operator’s manual.

EN

ENGLISH

-6- Clarke

®

Operator's Manual (EN) - BOOST 28

Procedures For Transporting

How to Put the Machine Into a Van or Truck

WARNING: This machine is heavy. Get

assistance before attempting

to transport or move it. Use

two able persons to move the

machine on a ramp or

incline. Always move slowly.

Do not turn the machine on a

ramp. Do not stop and leave

the machine on a ramp or

incline. The loading ramp

must be a minimum of 32"

wide.

WARNING: Machines can topple over if

guided over the edges of

stairs or loading docks and

cause injury or damage.

Stop and leave this machine

only on a level surface.

When you stop the machine,

put all switches into their

"OFF" position.

1. Make sure the loading ramp is at least eight

(8) feet (2.5m) long and a minimum of 32" (0.8m)

wide, and strong enough to support the machine.

2. Make sure the ramp is clean and dry.

3. Put the ramp in position.

4. Remove squeegee assembly before loading.

Clarke recommends that both the solution tank

and recovery tank are empty before loading.

5. Turn key switch "ON" .

6. Align the machine on a level surface five (5) feet

(2 m) in front of the ramp.

7. Put the traverse knob at full speed.

8. Push in either one of the forward/reverse

switches while pushing in the white reverse

switch. Back the machine up the ramp. See

figure 1.

9. Turn the key switch "OFF".

Figure #1

EN

ENGLISH

Clarke

®

Operator's Manual (EN) - BOOST 28 - 7 -

10. Fasten the machine to the vehicle. Clarke

recommends a strap over the top of the

machine and a strap to keep the machine from

rolling forward or backwards. If this is not

done, there is a possibility of the machine

toppling over. Four tie down points (2 along

each side of frame) are provided on machine for

securing machine.

How to Remove the Machine From a Van or

Truck

1. Make sure there are no obstructions in the area.

2. Make sure the unloading ramp is at least eight

(8) feet (2.5m) long and a minimum of 32"

(0.8m) wide, and strong enough to support the

machine.

3. Make sure the ramp is clean and dry.

4. Put the ramp in position.

5. Unfasten the machine.

WARNING: The machine is heavy.

Make sure you use two able

persons to assist in moving

the machine down the

ramp.

6. Turn the key switch "ON".

7. Set the traverse center knob to the slowest

forward speed setting. Carefully and slowly,

drive the machine to the top of the ramp and

start down.

8. While pushing in the right or left forward/reverse

switch the machine will go forward. See figure

2.

9. As the machine begins to travel down the ramp,

push in the forward/reverse switch to maintain a

slow downward speed.

10. Replace squeegee assembly after machine is

unloaded and ready to use.

Procedures For Transpoting (cont.)

Figure #2

EN

ENGLISH

-8- Clarke

®

Operator's Manual (EN) - BOOST 28

SYMBOLS USED ON BOOST 28

Solution Control

Brush Up/Down

Warning Label

with parking

brake

Warning

Power

Traverse Speed Control

Warning Label

without parking

brake

EN

ENGLISH

Clarke

®

Operator's Manual (EN) - BOOST 28 - 9 -

Machine Control Panel

Figure 3

Circuit Breakers

(See Fig 3, Items "E", "F", "G", & "H")

The circuit breaker reset buttons are located on the

rear cover. The breakers are located as follows:

Item E - Actuator Head (5 amp)

Item F - Vacuum Motor (30 amp)

Item G - Brush Motor (30 amp)

Item H - Traverse Motor (25 amp)

If a circuit breaker trips, determine which motor is not

operating and turn the key switch "OFF". Wait five

minutes and push the reset button back in. Turn the

key switch "ON" and try again. An authorized service

person should be contacted if the breaker trips again.

Control Handles (See Figure 3, Item "I")

The control handles are located at the rear of the

machine. They are used to guide the machine.

Solution Control Knob (See Figure 3, Item "J")

The solution control knob regulates the flow of chemi-

cal solution to the floor. To increase the flow, turn

knob clockwise. To decrease the flow, turn counter

clockwise. Full counter clockwise is OFF and full

clockwise is ON. Clarke recommends starting with

the knob set in the green section to provide the best

general cleaning with optimal water usage.

Traverse Speed Knob (See Figure 3, Item "K")

To increase speed, turn knob clockwise.

Brush Motor Switch (See Figure 3, Item "L")

To activate brush motor, push brush position switch to

down position. Brush Motor and solution flow will

activate when the traverse buttons are pushed. To

shut brush motor off, place brush position switch in up

position.

Key Switch (See Figure 3, Item "A")

The key switch turns "ON" the power to the control

panel. "O" is "OFF" and "I" is "ON".

Forward Reverse Switch (See Figure 3, Item "B")

The forward/reverse switch turns the traverse motor

"on" forward and if the brush motors are in the down

position, activates the brush motor/solution control

module. There is a two second delay for the pad

motor to stop after releasing the switch. Either the

right or the left switch can be used. Use either switch

in conjunction with the white reverse switch to reverse

the traverse motor.

Battery Meter (See Figure 3, Item "C")

The battery meter indicates the relative charge on the

battery pack. Do not continue to run the machine

when the needle is in the "red" area. This will shorten

the life of the battery pack.

Reverse Switch (See Figure 3, Item "D")

The reverse switch, when used in conjunction with one

of the forward/reverse switches, causes the machine to

reverse directions. The reverse speed is 70% of the

forward speed.

Vacuum Motor Switch (See Figures 4 & 5, pg. 10)

To activate vacuum motor, lower squeegee handle.

Handle has two positions. Lowest position is

operating position and the middle position is transport

to clear vacuum hose.

B

I

D

A

K

I

B

C

J

L

E

F

GH

EN

ENGLISH

-10- Clarke

®

Operator's Manual (EN) - BOOST 28

Machine Controls and Features

Squeegee Lift Handle, See Figures 4 and 5

The squeegee lift handle is located below the control

handles in the center. It is used to raise or lower the

squeegee. The vac motor is turned on when the

handle is lowered to either the first or last position.

Float Shut Off, See Figure 6

The shut-off switch for the vac motor is located in the

recovery tank. It automatically turns off the vac motor

when the recovery tank is full. NOTE: If excessive

foaming occurs in recovery tank, defoamer must

be added. Damage to vacuum motor could result

from foam.

Parking Brake (Optional), See Figure 7

NOTE: Parking Brake must be used if operating

machine on greater than 2% gradient.

The parking brake prevents movement of the machine.

CAUTION: Do not activate the parking brake

while the machine is moving.

The brake is located on the right hand side of the

machine on the transaxle motor. Turn the key

switch off or disconnect the power to the battery to

apply the brake.

There is a mechanical lever located on the brake.

This lever is an override. To manually release the

brake, rotate the lever clockwise. To return the

brake to normal or to apply the brake, rotate the

lever up counter clockwise.

NOTE: If the lever is left in the override

position, the brake will not function with the

key switch, and the machine will not operate.

Figure 6

Figure 4

Figure 5

Figure 7

EN

ENGLISH

Clarke

®

Operator's Manual (EN) - BOOST 28 - 11 -

Figure 8B

How To Install The Batteries

This machine uses either two 12-volt batteries or four - 6

volt batteries. The batteries are located in the battery

compartment under the recovery tank.

To install the batteries, follow this procedure:

1. Turn machine off. Set brake (if equipped).

2. Make sure recovery tank is empty.

3. Tip up the recovery tank until it locks in the full open

position. See figure 8A.

CAUTION: Before raising the tank, be sure

tank is empty.

NOTE: There is an intermediate position available

for holding the recovery tank open for charging

batteries. See figure 8B.

WARNING: Do not operate or perform mainte-

nance on the machine while the

recovery tank is in the intermediate

position. The tank can be acciden-

tally bumped and it may slam shut.

4. Place the batteries in the tray as shown in

figure 8C.

WARNING: The batteries are heavy. Lifting

batteries without help could result in

an injury. Get help to lift the batter-

ies.

WARNING: Working with batteries can be

dangerous. Always wear eye

protection and protective clothing

when working near batteries. NO

SMOKING!

5. Connect the cables between batteries and install

long battery cable assembly as indicated. See

figure 9.

6. Join the connector from the battery pack to the

connector on the control panel.

7. Close recovery tank by pulling up on the latch arm

and then slowly lowering the tank.

NOTE: Charge the batteries before using the

machine.

How To Prepare the Machine For Operation

Figure 9

Figure 8A

EN

ENGLISH

-12- Clarke

®

Operator's Manual (EN) - BOOST 28

Battery Maintenance

The electrical power to operate the machine comes

from the storage batteries. Storage batteries need

preventative maintenance.

WARNING: Working with batteries can

be dangerous. Always wear

eye protection and protective

clothing when working near

batteries. NO SMOKING!

To maintain the batteries in good condition, follow

these instructions:

1. Keep the electrolyte at the correct level. The

correct level is between 1/4" (1/2 cm) below the

bottom of the tube in each cell and above the

tops of the plates. Check the level of the electro-

lyte each time you charge the batteries. See

figure 10.

NOTE: Check the level of electrolyte prior to charging

the batteries. Be sure the plates in each cell are

covered with electrolyte before charging. Do not top

off the cells prior to charging the battery. Electrolyte

expands during charging. As a result, the electrolyte

could overflow from the cells. Always top off the cells

with distilled water after charging.

CAUTION: Irreversible damage will occur to

the batteries if electrolyte does

not cover the plates. Keep the

electrolyte at the correct level.

CAUTION: Machine damage and discharge

across the tops of the batteries

can occur if the batteries are over

filled. Do not fill the batteries up

to the bottom of the tube in each

cell. Wipe any acid from the

machine or the tops of the batter-

ies. Never add acid to a battery

after installation.

CAUTION: Batteries must be refilled with

distilled water only. Do not use

tap water as it may contain

contaminants that will damage

batteries.

2. Keep the tops of the batteries clean and dry.

Keep the terminals and connectors clean. To

clean the top of the batteries, use a damp cloth

with a weak solution of ammonia or bicarbonate

of soda solution. To clean the terminals and

connectors, use a terminal and connector

cleaning tool. Do not allow ammonia or bicar-

bonate of soda to get into batteries.

How To Prepare the Machine For Operation

Correct Level

Figure 11

Figure 10

3. Keep the batteries charged.

4. To drain battery compartment: (See figure 11)

a. Always wear protective eye protection and

protective clothing.

b. Add a weak solution of ammonia or bicarbon-

ate of soda solution to battery compartment to

neutralize any spilled acid.

c. Pull drain hose out from under transaxle.

d. Place hand behind flange and open valve.

e. When empty, close valve.

f. Replace valve and drain hose on top of

transaxle.

g. Neutralize any acid spills with ammonia or

bicarbonate of soda.

EN

ENGLISH

Clarke

®

Operator's Manual (EN) - BOOST 28 - 13 -

How To Charge The Batteries (Remote Charger)

WARNING: Charging the batteries in an area

without adequate ventilation

could result in an explosion. To

prevent an explosion, charge the

batteries only in an area with

good ventilation.

WARNING: Lead acid batteries generate

gases which could explode.

Keep sparks and flames away

from batteries. NO SMOKING!

To charge the batteries, follow this procedure:

1. Place the key switch is in the “OFF” position.

2. Before charging the batteries, the battery compart-

ment needs to be vented. To vent compartment, tip

up the recovery tank until it locks in the open

position (see figure 12A & 12B). To close the tank,

pull up on the arm and then slowly lower the tank to

the closed position.

CAUTION: Before raising tank, be sure tank

is empty.

WARNING: Do not operate or perform main-

tenance on the machine while

the recovery tank is in the open

position. The tank can be acci-

dentally bumped and it may slam

shut.

3. Put the charger on a flat surface. Make sure the

vents on the sides are at least two inches away from

walls and other objects. Make sure there are no

objects near the vents on the bottom of the charger.

4. Disconnect the battery pack connector from the

batteries.

5. Connect the DC connector on the charger to the

battery pack connector. See figure 13.

6. Connect the battery charger AC cord to a 15 amp

(min) 120V properly grounded wall receptacle.

NOTE: Make sure you plug into a circuit that is not

loaded by other equipment. Wall breakers may be

tripped and no charge will occur.

WARNING: Never charge a GEL battery with

an unsuitable battery charger.

Carefully follow the instructions

given by the manufacturer of the

batteries and battery charger.

NOTE: To prevent permanent damage to the batteries,

avoid their complete discharge. Never leave the batteries

completely discharged, even if the machine is not being

used. When recharging the batteries, keep the recovery

tank open. After every 20 recharging cycles, check the

level of the electrolyte and if necessary top off with

distilled water.

Figure 12A

Figure 12B

Figure 13

How To Prepare the Machine For Operation

EN

ENGLISH

-14- Clarke

®

Operator's Manual (EN) - BOOST 28

How To Charge The Batteries (On-Board Charger

Option)

WARNING: Charging the batteries in an area

without adequate ventilation could

result in an explosion. To prevent an

explosion, charge the batteries only

in an area with good ventilation.

WARNING: Lead acid batteries generate gases

which could explode. Keep sparks

and flames away from batteries. NO

SMOKING!

To charge the batteries, follow this procedure:

1. Make sure the key switch is in the “OFF” position.

2. Before charging the batteries, the battery compartment

needs to be vented. To vent compartment, tip up the

recovery tank until it locks in the open position (see figure

14A & 14B). To close the tank, pull up on the arm and

then slowly lower the tank to the closed position.

CAUTION: Before raising tank, be sure tank is

empty.

WARNING: Do not operate or perform mainte-

nance on the machine while the re-

covery tank is in the open position.

The tank can be accidentally bumped

and it may slam shut.

3. Connect the battery charger AC cord located at the rear

of the machine to a 15 amp (min) 120V properly grounded

wall receptacle.

4. Observe indicator light on the charger to ensure the

charging process has started. Yellow light indicates

state of charge. Steady on green light indicates the

batteries are fully charged.

NOTE: Make sure you plug into a circuit that is not loaded by

other equipment. Wall breakers may be tripped and no charge

will occur.

WARNING: Never charge a GEL battery with an

unsuitable battery charger. Carefully

follow the instructions given by the

manufacturer of the batteries and bat-

tery charger.

NOTE: To prevent permanent damage to the batteries, avoid

their complete discharge. Never leave the batteries com-

pletely discharged, even if the machine is not being used.

When recharging the batteries, keep the recovery tank open.

After every 20 recharging cycles, check the level of the

electrolyte and if necessary top off with distilled water.

How To Prepare the Machine For Operation

Figure 14A

Figure 14B

EN

ENGLISH

Clarke

®

Operator's Manual (EN) - BOOST 28 - 15 -

How To Install The Brush Or Pad

To install the brush or pad on the machine, follow this

procedure:

1. Turn the key switch "ON".

2. Put the brush switch in the "Up" position.

3. Turn the key switch "OFF".

4. Go to the front of the machine.

5. Press on a brush or pad, under the flex plates. See

figure 15.

NOTE: When using a black pad, position pad on head.

Lower head and operate momentarily to affix pad

to pad driver (if you have difficulty, position pad on

floor and lower head then operate.)

How To Remove The Brush Or Pad

To remove the brush or pad from the machine, follow this

procedure:

1. Turn the key switch "ON".

2. Put the brush switch in the "Up" position.

3. Turn the key switch "OFF".

4. Go to the front of the machine and pull downward on

the brush or pad until it releases from the flex plates.

See figure 16.

How To Prepare the Machine For Operation

Figure 15

Figure 16

EN

ENGLISH

-16- Clarke

®

Operator's Manual (EN) - BOOST 28

How To Operate The Machine

Figure 17

Figure 18

Figure 19

Figure 19A

C

How To Operate The Squeegee

The squeegee wipes the floor while the vacuum motor

removes the dirty solution from the floor. Use your

hand to lower or raise the squeegee handle. To

operate the squeegee, follow this procedure:

1. To lower the squeegee and start the vacuum

motor, move the squeegee lever to the right and

down. See figure 17.

2. To raise the squeegee, lift the squeegee lever up.

See figure 18.

NOTE: The center position lets the vacuum motor

continue to run with the squeegee off the floor to avoid

drips and also allows you to back up the machine.

How To Fill The Solution Tank

The solution tank can be filled in the front or through

the clear drain hose at the rear of the machine (See

figure 19). To fill the solution tank follow this proce-

dure:

1. Add a cleaning chemical to the solution tank.

For the correct amount of chemical, follow the

directions shown on the container.

2. Fill the solution tank with water. When filling

machine in the front with a hose, position hose

inside the fill screen as shown in figure 19A.

When filling machine from the rear, position clear

drain hose against bracket and insert hose as

shown in figure 20 Solution level can be viewed

from the back of the machine.

Figure 20

EN

ENGLISH

Clarke

®

Operator's Manual (EN) - BOOST 28 - 17 -

Figure 21

WARNING: Water solutions or cleaning

materials used with this type of

machine can leave wet areas on

the floor surface. These areas

can cause a dangerous condition

for the operator or other persons.

Always put CAUTION signs near

the area you are cleaning.

WARNING: Machines can ignite flammable

materials and vapors. Do not use

with or near flammables such as

gasoline, grain dust, solvents and

thinners. Only use a cleaning

concentration recommended by

the chemical manufacturer.

WARNING: Clarke recommends a maximum

water temperature of 120

o

F (49

o

C).

Operating The Machine

NOTE: Put the machine in the lowest traverse speed

setting. Use the machine in an area that has no

furniture or objects until you can do the following:

1. Move the machine in a straight direction, forward

and backward.

2. Stop the machine safely.

3. Turn the machine both left and right and return to a

straight direction.

To move the machine, follow this procedure:

1. Release the parking brake (if equipped with

machine).

2. Turn the key switch to the "ON" position

3. Raise the brush.

4. Raise the squeegee.

5. When either the left or right forward/reverse

switches (figure 21, item A) are pushed in, the

machine will go forward.

6. Control the speed of traverse by using the traverse

speed control knob (figure 21, Item C).

7. To stop, release the forward/reverse switch.

8. To reverse the machine, push in the white reverse

switch (figure 21 item B) and either the right or left

forward/reverse switch (figure 21 item A) at the

same time.

9. To stop, release the forward/reverse switch.

10. To turn the machine, push the rear of the machine

to the side.

11. When you stop the machine, turn the key switch

"OFF", remove the key and set the parking brake (if

equipped).

How To Operate The Machine

A

B

C

A

EN

ENGLISH

-18- Clarke

®

Operator's Manual (EN) - BOOST 28

How To Clean A Floor

WARNING: Water solutions or cleaning materials

used with this type of machine can leave

wet areas on the floor surfaces. These

areas can cause a dangerous condition for

the operator or other persons. Always put

CAUTION signs near the area you are

cleaning.

To clean a floor follow this procedure:

1. Set the parking brake (if equipped with machine.)

2. Put the water and a cleaning chemical in the clean

solution tank.

3. Release the parking brake (if equipped with machine.)

4. Turn the key switch "ON".

5. Lower the squeegee.

6. Put the brush switch in the down position.

7. Turn the solution knob to the right to activate the flow of

solution. Adjust the flow of clean solution to the flow

desired.

8. Move the machine across the floor in the forward

direction.

9. Make a 180° turn.

NOTE: When you make more passes across the floor, let the

brush clean approximately 2 inches (5 cm) of the area already

cleaned by the brush.

NOTE: During most cleaning procedures, apply and remove

the solution in one operation.

How To Clean A Very Dirty Floor

To clean a very dirty floor, follow this procedure:

1. Apply solution to the floor.

2. Do not lower the squeegee. This will keep the vacuum

motor off.

3. Lower the brush or pad and scrub the floor.

4. Scrub the floor again with additional solution and lower

the squeegee.

5. Pick up all the solution with the squeegee.

How To Operate The Machine (cont)

EN

ENGLISH

Clarke

®

Operator's Manual (EN) - BOOST 28 - 19 -

WARNING: Maintenance and repairs must be

done by authorized personnel only.

WARNING: Always empty the solution tank and

recovery tank before doing any

maintenance.

WARNING: Keep all fasteners tight.

These Maintenance Procedures Must Be Done

Every Day

Keep the machine clean, it will need fewer repairs and

have longer life.

Do These Procedures When You Begin Your Work

Period

1. Turn off key switch.

2. Disconnect AC power from battery charger (fol-

low charger instructions).

3. Disconnect the plug on the battery charger from

the battery pack connector, if using a remote

charger.

4. Join the connector from the batteries to the

control panel cable connection (remote charger

only). See figure 22.

5. Make sure the screen filter over the vacuum

motor is clean and in position. See figure 23.

6. Make sure the recovery tank lid is on correctly.

See figure 24.

7. Make sure the valve on the recovery drain hose is

clean. Tightly close the valve.

8. Make sure the brush or pad is in position and

installed correctly.

9. Check the installation of the squeegee and

squeegee hose.

10. Make sure the solution drain / level indicator hose

is secure on the storage mount on the rear of the

machine.

Maintenance

Figure 22

Figure 23

Figure 24

EN

ENGLISH

-20- Clarke

®

Operator's Manual (EN) - BOOST 28

Do These Procedures When You End Your Work

1. Drain the solution tank (Figure 25) and the recovery

tank (Figure 26). To drain the tanks , follow this

procedure:

a. Turn the key switch “OFF”.

b. Remove the drain hose from the back of the

machine.

c. Put the end of the hose over a drain or bucket.

d. Recovery Tank:

1.) Turn the valve handle to the left. Pull the

handle out to open the drain (Figure 27).

NOTE: Have the opening in the side of the valve away

from you when you open the valve.

2.) To open the valve completely, turn the

handle to the right. Pull the handle out of

valve (Figure 28).

Solution Tank:

When hose is lowered to water level, water will

flow.

2. Flush the tanks. To flush the tanks, put clean water in

the tank through the opening on top of the tank.

3. If a tank or drain hose has an obstruction, use a pressure

water hose to flush the tank or hose. Put the water hose

into the drain hose.

4. Leave the tanks and the recovery drain valve open to dry

in the air.

5. Check the squeegee blade. Use a cloth to clean the

squeegee blade. If the squeegee blade is damaged or

worn, turn or replace the blade.

6. Check and clean the solution lid gasket. Use a mild

cleaning solution and rinse the parts in clean water.

Check the batteries and if necessary add distilled water

after charging. The correct level is within 1/4 inch (1/2 cm)

of the bottom of the tube in each cell.

CAUTION: Tap water may contain contami-

nants that will damage batteries.

Batteries must be refilled with

DISTILLED WATER ONLY.

WARNING: Lead acid batteries generate

gases which can cause an explo-

sion. NO SMOKING. Always wear

eye protection and protective

clothing when working near

batteries.

Use a clean cloth and wipe the surface of the machine.

Charge the batteries. See the instruction in the section of

this book called “How To Charge The Batteries”.

Maintenance

Figure 25

Figure 26

Figure 27

Figure 28

La page charge ...

Clarke BOOST 28 Manuel utilisateur

Ce manuel convient également à

Clarke BOOST 28 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents