Twin Eagles Side Burner Le manuel du propriétaire

Side Burner
Twin Eagles
Marque
Twin Eagles
Modèle
Side Burner
Catégorie
Barbecues
Taper
Le manuel du propriétaire

Ce manuel convient également à

P/N: 24262E 01/19
FREESTANDING SIDE BURNER
INSTALLATION, USE, AND CARE MANUAL
MODEL:
TESB132F-C
A message to our customers…
Congratulations on the purchase of your TWIN EAGLES Freestanding Side Burner! Our
products are engineered for precision and designed for style. Each TWIN EAGLES product is
manufactured in the USA at our own state of the art facility in California.
This manual will give you easy to follow instructions for installing, operating and
maintaining your TWIN EAGLES freestanding side burner. We recommend reading this manual
carefully before your first use to ensure safety, proper care and operation.
At TWIN EAGLES, we want you to enjoy grilling and spending time together as much as
we do – making memories that linger long after the grill cools down.
Thank you and welcome!
Dante Cantal
Owner and Founder
FOR YOUR RECORDS
Please record the product information below and refer to it when contacting TWIN
EAGLES. This information is found on the rating/data plate, located on the inside back of the
unit.
Model #:__________________________________
Serial #: __________________________________
Date of Purchase: __________________________
Place of Purchase: __________________________
Type of Gas: NG LP
To the Installer:
Please read these instructions completely before installation and give this manual to the
owner.
To the Owner:
Keep this manual in a safe place for future reference.
IMPORTANT SAFETY INFORMATION
WARNING! Read this manual carefully and completely before using your side burner to ensure proper
operation, proper installation, proper servicing and to reduce the risk of fire, burn hazard and/ or other injury.
AVERTISSEMENT! Lire ce manuel avec soin et en entier avant l’utilisation de votre barbecue afin d’en
assurer un fonctionnement, une installation et un entretien adéquats et réduire le risque d’incendie, de brûlures
et d’autres blessures.
D A N G E R
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. If odor continues, keep away from the
appliance and immediately call your gas
supplier or fire department.
D A N G E R
S’il y a une odeur de gaz:
1. Coupez l’admission de gaz de l’appariel.
2. Éteindre toute flamme nue.
3. Si l’odeur continue, évite l’appareil et appelle
tout de suite votre fournisseur de gaz ou les
pompiers.
W A R N I N G
1. Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
A V E R T I S S E M E N T
1. Ne pas entreposer ni utiliser de l’essence ni
d’autres vapeurs ou liquides inflammables dans
le voisinage de l’appareil, ni de tout autre
appareil.
2. Une bouteille de propane qui n’est pas
raccordée en vue de son utilisation, ne doit pas
être entreposée dans le voisinage de cet
appareil ou de tout autre appareil.
THIS IS FOR OUTDOOR USE ONLY:
If stored indoors, detach and leave L.P. cylinder
outdoors.
C’EST POUR UTILISATION à L’ExTéRIEUR
SEULEMENT:
Si l’appareil est entreposé à l’interieur, enlever
les bouteilles et les laisser à l’extérieur.
B E F O R E L I G H T I N G
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn
the burner control(s) off, wait 5 minutes,
and repeat the lighting procedure.
A V A N T D ’ A L L U M E R
L ’ A P P A R E I L
1. Lisez les instructions avant d’allumer l’appareil.
2. Ouvrez le couvercle avant d’allumer l’appareil.
3. Si l’appareil ne s’allume pas en 5 secondes, fermez
le robinet du brûleur, attendez 5 minutes, et
procédez de nouveau à l’allumage.
GENERAL SAFETY REQUIREMENTS
• The installation of this appliance must conform with local codes or, in the absence of local codes, either the
National Fuel Gas Code, ANZI Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas Installation Code or
CAN/CGA-B149.2, Propane Installation Code.
• This outdoor cooking gas appliance is not intended to be installed in or on recreational vehicles and/or boats.
• This outdoor cooking gas appliance is intended for outdoors use and shall not be used in a building, garage
or any other enclosed area.
• Minimum clearance of 12 inches from the back and sides of the unit to adjacent combustible
construction must be maintained. This outdoor cooking gas appliance shall not be located under
overhead-unprotected combustible construction.
• The utilization of an external electrical source requires that when installed, this outdoor cooking gas
appliance must be electrically grounded in accordance with the local codes or, in the absence of local codes,
with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. Keep any
electrical supply cord, or the rotisserie motor cord and the fuel supply hose away from any heated surfaces.
• Keep your side burner in an area clear and free from combustible materials, gasoline and other flammable
vapors and liquids.
• DO NOT obstruct the flow of combustion and ventilation air to this appliance. Keep the ventilation openings
of the cylinder enclosure free and clear from debris.
• Check all gas connections for leaks with soapy water solution and brush. Never use an open flame.
(Reference page 3 for leak test procedure).
• Check flexible hoses for cuts and wear that may affect the safety before each use.
• Never use the side burner in a windy area.
• The pressure regulator and hose assembly supplied with the Twin Eagles Side Burner must be used.
Replacement pressure regulators and hose assemblies must be those specified by Twin Eagles.
In Massachusetts: All gas products must be installed using a “Massachusetts” licensed plumber or
gasfitter. A “T” handle type manual gas valve must be installed in the gas supply line to this
appliance. This applies to permanently installed natural gas and propane installations. This does
not apply to propane portable installations using a 20 pound tank.
TABLE OF CONTENTS
INSTALLATION INSTRUCTIONS.....................................................................................................................
LEAK TEST……………………………………………………………………………………………………….
OPERATING INSTRUCTIONS…………………………………………………………………………………
CLEANING & MAINTENANCE
o STAINLESS STEEL……………………………………………………………………………………….
o S-GRATE…………………………………………………………………………………………………..
o SPIDER AND INSECT WARNING………………………………………………………………………
REPLACEMENT PARTS
o EXPLODED VIEW………………………………………………………………………………………...
o REPLACEMENT PARTS LIST…………………………………………………………………………...
o WIRING DIAGRAM………………………………………………………………………………………
o TROUBLE SHOOTING GUIDE…………………………………………………………………………..
LIMITED PRODUCT WARRANTY……………………………………………………………………………
WARRANTY REGISGRATION CARD
1
3
4
4
5
5
6
7
8
9
10
1
INSTALLATION INSTRUCTIONS
1. Remove the front side shelf bracket. Save the screws.
2. Remove side shelf off cart. Store in the cart under the grill. Reinstall side shelf bracket using the saved
screws.
3. Insert pin of the rear bracket into the hole on the back side of the side burner housing. Then slide the
front pin into the slotted hole on the front side of the side burner housing.
4. Secure the side burner to the cart using the ¼-20 stainless steel nuts and bolts provided.
o For easy access inside the grill base cabinet, the access doors are removable by snapping off the
hinges.
5. Hook-up gas connection as shown. Use pipe sealant suitable for use with LP and NG. Check for leaks
using the soapy water method outlined in the “Leak Test” section (pg. 3).
LEAK
TEST
LEAK
TEST
2
6. Locate and connect extension wires from side burner to grill.
7. Reinstall access door if removed.
3
LEAK TEST
CAUTION BEFORE TESTING
▪ Finding and/or fixing a gas leak is NOT a “DO-IT-YOURSELF” procedure.
▪ NEVER USE THE SIDE BURNER WITHOUT FIRST LEAK TESTING THE GAS CONNECTIONS.
▪ WARNING: DO NOT USE OPEN FLAME TO CHECK FOR LEAKS. USE OF AN OPEN FLAME
COULD RESULT IN A FIRE, EXPLOSION AND BODILY HARM.
▪ DO NOT SMOKE WHILE PERFORMING THE LEAK TEST!
▪ To prevent fire or explosion hazard, DO NOT use or permit sources of ignition in the area while performing
a leak test. Perform leak test outdoors only.
▪ Check to ensure that flexible hoses do not have any cuts and wear that may affect the safety before each use.
Only the factory supplied hose and regulator must be used. Use only replacement regulator and hose
assemblies specified by Twin Eagles.
LEAK TEST
1) Prepare a leak testing solution of sudsy water by mixing in a spray bottle with half liquid soap and half
water.
2) Confirm that all control knobs are in the OFF position.
3) Turn the main gas valve supply ON.
4) Apply leak testing solution by spraying on the pipe joints, fittings, and hose.
5) A gas leak is detected if;
a) there is a faint gas smell and/or…
b) …growing bubbles appear on any of the connection points and/or hose, DO NOT attempt to ignite the
side burner and IMMEDIATELY turn off the gas supply valve.
6) When there is a gas leak, call a qualified service technician. DO NOT use the side burner until the leak is
corrected.
4
OPERATING INSTRUCTIONS
1. Make sure all knobs are in the “OFF” position.
2. Turn “on” the gas at source. Caution: If you smell gas, shut off gas supply and
call for service.
3. Before lighting, remove the side burner cover or any cooking utensils from the
burner grate.
4. Push-in and turn the burner knob counterclockwise to “HI” (LARGE FLAME)
position and hold the knob in. You should hear a continuous clicking sound and
see sparks being provided to the burner. (If clicking sound is weak, replace the
9V battery).
5. If the burner does not ignite within 5 seconds, turn the burner to “OFF” and wait
for five minutes. Repeat the above procedures or try the following manual
lighting procedures
a. Hold a lit match next to the burner ports
b. Push and turn the burner knob counterclockwise to ignite the burner.
6. Adjust flame setting to “LOW” or “MEDIUM” or “HIGH”, if desired.
7. Caution: Do not leave the side burner unattended while cooking.
8. To shutdown the burner, push and turn the burner knob clockwise to “OFF”.
9. For complete shutdown, turn “off” the gas at source.
CLEANING AND MAINTENANCE
GENERAL OVERVIEW
Proper care, maintenance, and cleaning will help ensure a long life of your Freestanding Side Burner. Periodic
cleaning will help avoid accumulation of flammable grease, fats, and other debris.
Caution: Always allow the Freestanding Side Burner to cool before cleaning.
STAINLESS STEEL & GENERAL PRODUCT CARE
To keep your TWIN EAGLES products free of surface corrosion and in good working order, it is important to
take additional precautions under certain conditions.
If your TWIN EAGLES products are located in corrosive conditions, such as:
• A coastal environment where corrosive salty air is present
• Near a swimming pool, hot tub or water feature with exposure to corrosive pool chemicals and/or
chlorinated water
• Areas where muriatic acid (hydrochloric acid) or other corrosive cleaning solutions are used to clean
concrete and masonry
• Areas where corrosive masonry dust and debris are created by cutting stone or mixing cements
These conditions can create a highly corrosive environment that will cause the corrosions resistant type 304
stainless steel to develop surface oxidation, corrosions or rust.
5
TWIN EAGLES products have been tested in saline solutions, highly chlorinated solutions and have been tested
against exposure to highly acidic foods. The test results proved the type 304 stainless steel can withstand
exposure over prolonged periods of time. However, the conditions outlined above, along with neglect, can lead
to surface corrosion or rust.
It is recommended that your TWIN EAGLES products be kept dry and covered when not in use. This is even
more important when long-term storage is intended.
Do not allow food particles or grease to be left inside your TWIN EAGLES products. These can attract rodents,
which are unsanitary and are likely to cause physical damage by chewing on the wiring, which can cause
permanent damage to the electrical components.
If you are located along the coast or in the desert, wind driven sand is extremely abrasive and can pit and
scratch the stainless steel. Keep your TWIN EAGLES products covered when not in use.
When routine cleaning, maintenance and awareness of the conditions outlined above, you can enjoy many years
of service from your TWIN EAGLES products. In the event that surface corrosion has developed on the
stainless steel, it is typically not the stainless steel that is corroding but corrosive particles that have been
deposited on the surface.
TWIN EAGLES products are made of all welded stainless steel. It is non-rusting and non-magnetic. Never clean
the stainless steel when it is hot. After the initial use, some areas may discolor. This is a normal discoloration
caused by the intense heat given off by the burners.
Specks of grease can gather on the surface of the stainless steel and get baked-on. These can be removed by
using a mild abrasive pad with a stainless steel cleaner. Use the mildest cleaner and always scrub in the
direction of the grain. Do not use steel wool to clean the grill.
Do not use abrasives on the polished highlights. Be extra careful when cleaning around the highlights. Metal
polisher or mild chrome cleaner can be used to bring back the luster on highlights. To touch-up minor scratches
in the stainless steel, sand the affected surface very lightly, with 100-dry grit emery sandpaper in the direction
of the grain.
S-GRATE
The easiest way to clean the grates is to scrub them with a soapy cloth after cooking is completed, the flame is
turned off, and the side burner has had time to cool. The grate may discolor, this is a natural reaction to the
intense heat given off by the burners.
SPIDER AND INSECT WARNING
Spiders and other insects can nest in the burners of this and any other grills, which causes the gas to flow from
the front of the burner. This dangerous “condition” can cause a fire behind the valve panel, damaging the grill
and making the grill unsafe to operate. Inspect the burners once a year or if the grill has not been used for more
than one month or if any of the following conditions occur:
1) The smell of gas in conjunction with the burner flames appearing yellow.
2) The grill does not reach temperature.
3) The grill heats unevenly.
4) The burners make popping noises.
6
EXPLODED VIEW
7
REPLACEMENT PARTS LIST
Number
Part Number
Description
TESB132F-BL
TESB132F-BN
1
S20256
Top Cover
1
1
2
S13806
S-Grates
1
1
3
S20255WY
Wind Guard
1
1
4
S13309
Enameled Cap
2
2
5
S13308
Enameled Ring
2
2
6
S13307
Aluminum Bowl
2
2
7
S13306
Base with Electrode, LP
2
8
S13320
Base with Electrode, NG
2
9
S13204
Logo, Twin Eagles
1
1
10
S14160
Tinnerman Clips
2
2
11
S16196
12V Switch, Illuminated
1
1
12
S13270
Light Bezel Assembly
2
2
13
S13224
Lens, Light Bezel
2
2
14
S13226
Rubber Retention Ring
2
2
15
S13235
Knob, Illuminated
2
2
16
S26360-132WY
Front Panel Welded Assembly
1
1
17
S16272
Battery Pack
1
1
18
S16323
Ignition Module
1
1
19
S21788
Bracket, Module, Ignition
1
1
20
S15149YSB
Gas Valve w/ Microswitch
2
2
21
S12710
Manifold
1
1
22
S12606
1/8 Pipe Plug
1
1
23
S12609
Nut and Sleeve, .125 NPT x .312 CC
2
2
24
S12610
Bushing Reducer, Brass, .50 x .375
2
2
25
S15303
Regulator, NG
1
26
S12602
Adapter, ½ NPT x 3/8 Flare
1
27
S15344
Regulator, LP
1
28
S12413
Gas Tube, Front
1
1
29
S12414
Gas Tube, Rear
1
1
NON-SHOWN PARTS
S13313
Center Orifice,# 82, NG
2
S13314
Outside Orifice, #175, NG
2
S13317
Center Orifice, #50, LP
2
S13318
Outside Orifice, #100, LP
2
S12403
Tubing, 3/8 flareX3/8 FlareX24"Long
1
1
S14105
Hex Nut, ¼-20 Hex
2
2
S14125
Hex Bolt, ¼-20 x .500
2
2
S12637
Connector, Brass, 3/8 M Flare x 1/4 MPT NH
1
1
S16006
Wire Loop, 8”
1
1
S16339
Wire Harness, Module
1
1
S16259
Wire Harness, 16” Extension
1
1
8
WIRING DIAGRAM
TESB132/132F-C WIRING DIAGRAM SHOWN
9
TROUBLE SHOOTING GUIDE
BEFORE CALLING FOR SERVICE:
If your Twin Eagles Side Burner does not function properly, use the following trouble shooting guide before
contacting your dealer for service. The troubleshooting guide may save you the cost of a service call and the
inconvenience of being without your Side Burner. IMPORTANT: before any troubleshooting, make sure your
Twin Eagles product is allowed adequate time to cool.
PROBLEM
WHAT TO DO
Side Burner will not light.
1. Push in the knob and verify that the igniter sparks.
2. If the igniter does not spark verify proper power supply. 9V.
a. Purge the line of any trapped air.
b. Check if you can match-light the burner.
c. Check to see that the other burners operate (if you own a 2-burner Side
Burner).
NOTE: It is normal to hear a popping sound when the grill burners are
first turned ON.
Burner flame is yellow and
gas odor can be smelled.
1. Check the burner ring(s) for obstruction…ex. Spiders, insects, etc.
2. Check any source of gas leak.
Low heat generated with
knob in HI position.
1. Check if the problem is isolated to only one burner. If it appears so, clean
the orifice and burner, clearing ports of any obstruction.
2. Check for any bent or kinked fuel hose.
3. Check for proper gas supply and pressure.
4. If using LP gas, check for empty tank.
Too much heat.
1. Check for damaged orifice or no orifice.
2. Check for unauthorized regulator adjustment.
Excessive flare-up.
1. Check if the enamel rings are dirty. Clean if necessary.
Burner blows out
1. Check for any burner defect.
2. Check for proper burner installation.
3. Check if fuel mixture is too lean.
4. Check if gas supply is sufficient.
5. Check if LP tank is empty.
6. Check if the Side Burner location is subject to high winds.
Bezel light / Switch light
will not turn ON.
1. Check if the unit is plugged into proper voltage (GFCI 120V).
2. Replacement of the Bezel Assembly may be required.
Spark igniter
will not turn ON.
1. Check if the unit is plugged into proper voltage (9V).
2. Check if microswitch makes contact.
10
LIMITED TWO YEAR WARRANTY: Twin Eagles warrants the Side Burner to be free from defects in materials and
workmanship under normal residential use for a period of two years from the original
date of purchase. The actual part will be repaired or replaced, free of charge, with the
owner paying for all other costs including labor, shipping and handling.
ONE-YEAR FULL WARRANTY: Twin Eagles warrants the Side Burner and all other components to be free from
defects in materials and workmanship under normal residential use for a period of one
year from the original date of purchase. Twin Eagles will repair or replace parts found
to be defective at no cost to the original purchaser. Warranty service must be performed
by a Twin Eagles authorized representative during normal business hours.
NINETY (90) DAY RESIDENTIAL PLUS WARRANTY: This warranty applies to applications where use of the
product extends beyond normal residential use such as bed and breakfast inn and
private clubs. The actual part will be repaired or replaced, free of charge, with the
owner paying for all other costs including labor, shipping and handling. This warranty
excludes all commercial locations such as restaurants and food service locations.
WARRANTY LIMITATIONS & EXCLUSIONS
This warranty shall apply only to the products purchased and located in the continental United States and Canada. The
warranty coverage begins on the original date of purchase and proof of date of purchase is required. To activate the
warranty, we require that you send in the attached warranty registration card. This warranty applies only to the original
owner and may not be transferred.
This warranty excludes discoloration, surface scratches, weather and atmospheric related staining, and minor surface rust
and oxidation which are normal conditions and are to be expected with any outdoor product. This warranty does not apply
to damages resulting from negligence, alteration, misuse, abuse, accident, natural disaster, loss of electrical power to the
product for any reason, improper installation or improper operation, unauthorized adjustments or calibrations, dings,
dents, scratches, or damages due to harsh cleaning chemicals. This warranty does not apply to commercial use, or to
products with altered or removed serial numbers. Display models are generally sold “as is” and are subject to the
following warranty exclusions: missing components, scratches, dents and other exterior or cosmetic damages, electrical,
gas and ignition system. Twin Eagles shall not be liable for incidental, consequential, special or contingent damages
resulting from its breach of this written warranty or any implied warranty.
WARRANTY SERVICE & REPLACEMENT PARTS: Call your authorized selling dealer or call Twin Eagles directly
at 800-789-2206. Be prepared to furnish the following information: Purchaser’s name, model and serial number of the
grill, date of purchase and the accurate description of the problem. Twin Eagles will not pay for service calls for
correcting an installation problem. Owner shall be responsible for proper installation, providing normal care and
maintenance, providing proof of purchase upon request and making the grill accessible for service. In the event of any
warranty replacement, all removal, replacement, installation and shipping costs are the responsibility of the owner.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusions of or limitations on
consequential damages. This warranty gives you specific legal rights and you may have other rights, which vary from
state to state.
THIS PAGE IS INTENTIONALLY LEFT BLANK
HOW TO OBTAIN SERVICE
For service, please contact your TWIN EAGLES dealer or call TWIN EAGLES direct at
(800) 789-2206 or (562) 802-3488 or fax (562) 802-3391
Mailing address:
Twin Eagles, Inc.
13259 East 166
th
Street
Cerritos, CA 90703
Visit us at www.twineaglesgrills.com
Please provide:
▪ Model number
▪ Serial Number
▪ Date of Purchase
▪ A description of the problem
WARRANTY REGISTRATION
Customer Name
Model #
Address
Serial #
City, State
Date Purchased
Zip
Dealer’s Name
Phone #
Dealer’s Address
e-mail:
This Warranty Registration card must be returned within thirty days of purchased to properly activate your warranty. This information
is for our internal use only.
Or you may register online at https://www.twineaglesgrills.com/resources/warranty-registration
Customer Service
ATTN: Warranty Department
13259 East 166
th
Street
Cerritos, CA 90703
Fax no. (562) 802-3391
Place
Postage
Here
Cut
Here
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Twin Eagles Side Burner Le manuel du propriétaire

Side Burner
Twin Eagles
Marque
Twin Eagles
Modèle
Side Burner
Catégorie
Barbecues
Taper
Le manuel du propriétaire
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes