Zanussi ZDI22003XA Manuel utilisateur

Catégorie
Lave-vaisselle
Taper
Manuel utilisateur
GETTING
STARTED?
EASY.
User Manual
ZDI22003XA
EN User Manual 2
Dishwasher
FR Notice d'utilisation 20
Lave-vaisselle
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair information:
www.zanussi.com/support
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
This appliance is intended to be used in household and similar
applications such as:
farm houses; staff kitchen areas in shops, offices and other
working environments;
by clients in hotels, motels, bed & breakfast and other
residential type environments.
2
Do not change the specification of this appliance.
The operating water pressure (minimum and maximum) must be
between 0.5 (0.05) / 8 (0.8) bar (MPa)
Follow the maximum number of 13 place settings.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
Put the cutlery in the cutlery basket with the sharp ends
pointing down or put them in the cutlery drawer in a horizontal
position with the sharp edges down.
Do not leave the appliance with the open door unattended to
avoid stepping accidentally onto it.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
If the appliance has ventilation openings in the base, they must
not be covered e.g. by a carpet.
The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
SAFETY INSTRUCTIONS
INSTALLATION
WARNING! Only a qualified person
must install this appliance.
Remove all the packaging.
Do not install or use a damaged appliance.
Do not use the appliance before installing it in
the built-in structure due to safety manner.
Follow the installation instructions supplied with
the appliance.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Do not install or use the appliance where the
temperature is less than 0 °C.
Install the appliance in a safe and suitable place
that meets installation requirements.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
The appliance must be earthed.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
3
This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
WATER CONNECTION
Do not cause damage to the water hoses.
Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
Ensure that there are no visible water leaks
during and after the first use of the appliance.
The water inlet hose has a safety valve and a
sheath with an inner mains cable.
WARNING! Dangerous voltage.
If the water inlet hose is damaged, immediately
close the water tap and disconnect the mains
plug from the mains socket. Contact the
Authorised Service Centre to replace the water
inlet hose.
USE
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Dishwasher detergents are dangerous. Follow
the safety instructions on the detergent
packaging.
Do not drink and play with the water in the
appliance.
Do not remove the dishes from the appliance
until the programme is complete. Some
detergent may remain on the dishes.
Do not store items or apply pressure on the
open door of the appliance.
The appliance can release hot steam if you open
the door while a programme operates.
INTERNAL LIGHTING
WARNING! Risk of injury.
Concerning the lamp(s) inside this product and
spare part lamps sold separately: These lamps
are intended to withstand extreme physical
conditions in household appliances, such as
temperature, vibration, humidity, or are intended
to signal information about the operational
status of the appliance. They are not intended to
be used in other applications and are not
suitable for household room illumination.
To replace the internal lighting, contact the
Authorised Service Centre.
SERVICE
To repair the appliance contact the Authorised
Service Centre. Use original spare parts only.
Please note that self-repair or non-professional
repair can have safety consequences and might
void the guarantee.
The following spare parts will be available for 7
years after the model has been discontinued:
motor, circulation and drain pump, heaters and
heating elements, including heat pumps, piping
and related equipment including hoses, valves,
filters and aquastops, structural and interior
parts related to door assemblies, printed circuit
boards, electronic displays, pressure switches,
thermostats and sensors, software and firmware
including reset software. Please note that some
of these spare parts are only available to
professional repairers, and that not all spare
parts are relevant for all models.
The following spare parts will be available for 10
years after the model has been discontinued:
door hinge and seals, other seals, spray arms,
drain filters, interior racks and plastic peripherals
such as baskets and lids.
DISPOSAL
WARNING! Risk of injury or
suffocation.
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent children and
pets to get closed in the appliance.
4
EASY START
1 3
456
2
1
On/off indicator
2
Programme marker
3
Indicators
4
Delay button
5
Start button
6
Programme knob
INDICATORS
Washing phase. It comes on when the washing phase operates.
Drying phase. It comes on when the drying phase operates.
End indicator.
Salt indicator. It is always off while the programme operates.
PROGRAMMES
The order of the programmes in the table may not reflect their sequence on the control panel.
5
Programme
Degree of soil
Type of load
Programme phases
Consumption values
1)2)
Duration
(min)
Energy
(kWh)
Water
(l)
3)
Normal soil
Crockery and
cutlery
Prewash
Wash 50 °C
Rinses
Dry
227
4)
/
227
5)
1.039
4)
/
1.036
5)
11
4)
/
9.9
5)
Heavy soil
Crockery,
cutlery, pots
and pans
Prewash
Wash 70 °C
Rinses
Dry
160 1.052 -
1.285
11.1 -
13.6
Normal soil
Crockery and
cutlery
Prewash
Wash 65 °C
Rinses
Dry
90 0.886 -
1.083
9.6 - 11.7
6)
Fresh soil
Crockery and
cutlery
Wash 60 °C
or 65 °C
Rinses
30 0.556 -
0.680
9.2 - 11.2
7)
All Prewash 15 0.012 -
0.015
3.4 - 4.2
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the
quantity of dishes can change the values.
2) The values for programmes other than ECO are indicative only.
3) This programme offers the most efficient use of water and energy consumption for crockery and cutlery
with normal soil. This is the standard programme for test institutes. This programme is used to assess
compliance with the Ecodesign Comission Regulation (EU) 2019/2022.
4) In accordance with the 1016/2010 regulation.
5) In accordance with the 2019/2022 regulation.
6) This programme is suitable for washing a load or a half load with fresh soil. It gives good washing re-
sults in a short time.
7) With this programme, you can quickly rinse off food remains from dishes and prevent odours forming in
the appliance. Do not use detergent with this programme.
INFORMATION FOR TEST INSTITUTES
To receive the necessary information for conducting performance tests (e.g. according to EN60436 ),
send an email to:
In your request, please include the product number code (PNC) found on the rating plate.
For any other questions regarding your dishwasher, please refer to the service book provided with your
appliance.
6
SETTINGS
PROGRAMME SELECTION MODE
Programme selection mode allows selecting and
starting a washing programme with applicable
options and entering user mode to change the
appliance settings.
To enter the programme selection mode:
Rotate the programme knob to a position in which
the programme marker points at one of available
programmes.
If the appliance is on and the programme marker
points at one of available programmes, but the
control panel does not indicate the appliance is in
the programme selection mode, turn the appliance
off and on again or implement the CANCEL
procedure.
CANCEL PROCEDURE
Use CANCEL to:
Cancel a currently running programme.
Stop the countdown of
option.
Bring the appliance back to the programme
selection mode.
To implement CANCEL:
Press and hold until the appliance is in the
programme selection mode.
USER MODE
Enter user mode to change the following appliance
settings:
Adjust the level of the water softener according
to the water hardness.
Activate or deactivate AirDry.
Before entering the user mode, make sure the
appliance is in the programme selection mode.
To enter the user mode:
Press and hold
and simultaneously turn the
knob counterclockwise until the programme marker
is in position.
The on/off indicator and start to flash.
As the appliance stores the saved settings, there is
no need to configure it before every cycle.
ADJUSTING THE WATER SOFTENER
Make sure the programme marker points at the
on/off indicator.
1. Press and hold and simultaneously turn the
knob counterclockwise until the programme
marker is in position.
2. Release when the on/off indicator and
start to flash.
The intermittent flashing of the indicator shows
the current water softener setting (e.g. 5 flashes +
pause + 5 flashes... = level 5).
3. Press repeatedly to change the setting.
Each pressing of the button increases the
level number by one. After reaching level 10,
the count starts again from level 1.
4. Turn the knob back to the position of the on/off
indicator to confirm and save the setting.
THE WATER HARDNESS TABLE
The water softener removes minerals from the water
supply, which would have a negative effect on the
washing results and on the appliance.
The higher the content of these minerals, the harder
your water is. Water hardness is measured in
equivalent scales.
The water softener should be adjusted according to
the hardness of the water in your area. Your local
water authority can advise you on the hardness of
the water in your area. It is important to set the right
level of the water softener to assure good washing
results.
Water hardness
German degrees
(°dH)
French degrees
(°fH)
mmol/l
Clarke de-
grees
Water softener level
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
7
German degrees
(°dH)
French degrees
(°fH)
mmol/l
Clarke de-
grees
Water softener level
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27
5
1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5
1
2)
1) Factory setting.
2) Do not use salt at this level.
Regardless of the type of detergent used, set
the proper water hardness level to keep the
salt refill indicator active.
Multi-tabs containing salt are not
effective enough to soften hard water.
Regeneration process
For the correct water softener operation, the resin
of the softener device needs to be regenerated
regularly. This process is automatic and is the part
of the normal dishwasher operation.
When the prescribed quantity of water (see values
in the table) has been used since the previous
regeneration process, a new regeneration process
will be initiated between the final rinse and the
programme end.
Water softener level Amount of water (l)
1 250
2 100
3 62
4 47
5 25
6 17
7 10
8 5
9 3
Water softener level Amount of water (l)
10 3
In case of the high water softener setting, it may
occur also in the middle of the programme, before
the rinse (twice during a programme). Regeneration
initiation has no impact on the cycle duration,
unless it occurs in the middle of a programme or at
the end of a programme with a short drying phase.
In that cases, the regeneration prolongs the total
duration of a programme by additional 5 minutes.
Subsequently, the rinsing of the water softener that
lasts 5 minutes may begin in the same cycle or at
the beginning of the next programme. This activity
increases the total water consumption of a
programme by additional 4 litres and the total
energy consumption of a programme by additional
2 Wh. The rinsing of the softener ends with a
complete drain.
Each performed softener rinse (possible more than
one in the same cycle) may prolong the programme
duration by another 5 minutes when it occurs at any
point at the beginning or in the middle of a
programme.
8
All the consumption values mentioned
in this section are determined in
accordance with the currently
applicable standard in laboratory
conditions with water hardness
2.5mmol/L according to the
2019/2022 regulation (water softener:
level 3).
The pressure and the temperature of
water as well as the variations of the
mains supply can change the values.
AIRDRY FUNCTION
AirDry improves the drying results with less energy
consumption.
While the drying phase operates, the
device opens the appliance door. The
door is then kept ajar.
By default, AirDry is activated with all programmes
excluding (if applicable), but it is possible to
deactivate it.
DEACTIVATING AIRDRY
Make sure the programme marker points at the
on/off indicator.
1. Press and hold and simultaneously turn the
knob counterclockwise until the programme
marker is in position.
2. Release when the on/off indicator and
start to flash.
3. Turn the knob counterclockwise until the
programme marker is in position.
The indicator indicates the current setting. If
on = AirDry is on, if off = AirDry is off.
4. Press to activate or deactivate AirDry.
5. To confirm and save the setting, turn the knob
back to the position of the on/off indicator.
CAUTION! If children have access to
the appliance, it is advised to
deactivate AirDry as opening the door
may pose a danger.
BEFORE FIRST USE
1. Make sure that the current level of the
water softener agrees with the hardness
of the water supply. If not, adjust the level
of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any processing
residuals that can still be inside the appliance.
Do not use detergent and do not put dishes in
the baskets.
After starting the programme, the appliance
recharges the resin in the water softener for up to 5
minutes. The washing phase starts only after this
procedure is complete. The procedure is repeated
periodically.
ADDING SALT
Before the first use, put one litre of water in the salt container.
9
CAUTION! Water and salt can come out of the salt container during filling. To prevent
corrosion, start a programme immediately after filling the salt container.
ADDING RINSE AID
2
1
4
3
2
1
A
The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot
rinse phase. Fill the rinse aid dispenser when the lens (A) is clear.
DAILY USE
1. Open the water tap.
2. Set the correct programme for the type of load
and the degree of soil.
Make sure that the appliance is in Programme
selection mode.
If the salt indicator is on, fill the salt
container.
3. Load the baskets.
4. Add the detergent.
5. Start the programme.
ADDING DETERGENT
2
1
If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance
door.
10
ADDING MULTI-TABLETS
2
1
Do not fill the salt container and the rinse aid dispenser.
Set the rinse aid dispenser to the lowest position.
STARTING A PROGRAMME
1. Open the water tap and close the appliance
door.
2. Turn the programme knob clockwise or
counterclockwise to select a programme.
3. Set applicable options (if available).
4. Press .
The appliance starts working.
DELAY OPTION
1. Select a programme.
2. Press the button to delay the programme
start.
The indicator is on.
3. Press to start the countdown.
The programme starts running automatically when
the countdown is complete.
OPENING THE DOOR WHILE THE
APPLIANCE OPERATES
Opening the door while a programme is running
stops the appliance. It may affect the energy
consumption and the programme duration. After
closing the door, the appliance continues from the
point of interruption.
If the door is opened for more than 30
seconds during the drying phase, the
running programme ends. It does not
happen if the door is opened by AirDry
function.
Do not try to close the appliance door
within 2 minutes after AirDry
automatically opens it as this may
cause damage to the appliance.
If, afterwards, the door is closed for at
least 3 minutes, the running
programme ends.
AT THE END OF THE PROGRAMME
When the programme is complete, the indicator
is on. After 5 minutes the appliance
automatically turns off to decrease energy
consumption.
1. To entirely deactivate the appliance, turn the
programme knob to align the programme
marker with the on/off indicator.
2. Close the water tap.
HINTS AND TIPS
GENERAL
Follow the hints below to ensure optimal cleaning
and drying results in daily use and to protect the
environment.
Washing dishes in the dishwasher as instructed
in the user manual usually consumes less water
and energy than washing dishes by hand.
Load the dishwasher to its full capacity to save
water and energy. For best cleaning results,
arrange items in the baskets as instructed in the
user manual and do not overload the baskets.
Do not pre-rinse dishes by hand. It increases
the water and energy consumption. When
needed, select a programme with a prewash
phase.
Remove larger residues of food from the dishes
and empty cups and glasses before putting
them inside the appliance.
Soak or slightly scour cookware with firmly
cooked-on or baked-on food before washing it
in the appliance.
11
Make sure that items in the baskets do not
touch or cover each other. Only then can the
water completely reach and wash the dishes.
You can use dishwasher detergent, rinse aid
and salt separately or you can use the multi-
tablets (e.g. ''All in 1''). Follow the instructions
on the packaging.
Select a programme according to the type of
load and the degree of soil. offers the
most efficient use of water and energy
consumption.
To prevent limescale buildup inside the
appliance:
Refill the salt container whenever
necessary.
Use the recommended dosage of the
detergent and rinse aid.
Make sure that the current level of the water
softener agrees with the hardness of the
water supply.
Follow the instructions in the chapter "Care
and cleaning".
THE WATER SOFTENER
The water softener removes minerals from the water
supply, which would have a detrimental effect on
the washing results and on the appliance.
The higher the content of these minerals, the harder
your water is. Water hardness is measured in
equivalent scales.
The water softener should be adjusted according to
the hardness of the water in your area. Your local
water authority can advise you on the hardness of
the water in your area. It is important to set the right
level of the water softener to assure good washing
results.
USING SALT, RINSE AID AND DETERGENT
Only use salt, rinse aid and detergent for
dishwasher. Other products can cause damage
to the appliance.
In areas with hard and very hard water we
recommend to use plain dishwasher detergent
(powder, gel, tablets containing no additional
agents), rinse aid and salt separately for optimal
cleaning and drying results.
At least once a month run the appliance with the
use of appliance cleaner which is particularly
suitable for this purpose.
Detergent tablets do not fully dissolve with short
programmes. To prevent detergent residues on
the tableware, we recommend that you use the
tablets with long programmes.
Always use the correct quantity of detergent.
Insufficient dosage of detergent can result in
poor cleaning results and hard-water filming or
spotting on the items. Using too much detergent
with soft or softened water results in detergent
residues on the dishes. Adjust the amount of
detergent based on the water hardness. Refer
to the instructions on the detergent packaging.
Always use the correct quantity of rinse aid.
Insufficient dosage of rinse aid decreases the
drying results. Using too much rinse aid results
in bluish layers on the items.
Make sure that the water softener level is
correct. If the level is too high, the increased
quantity of salt in the water might result in rust
on cutlery.
WHAT TO DO IF YOU WANT TO STOP USING
MULTI-TABLETS
Before you start to use separately detergent, salt
and rinse aid do the following procedure.
1. Set the highest level of the water softener.
2. Make sure that the salt and rinse aid containers
are full.
3. Start the shortest programme with a rinsing
phase. Do not add detergent and do not load
the baskets.
4. When the programme is completed, adjust the
water softener according to the water hardness
in your area.
5. Adjust the released quantity of rinse aid.
LOADING THE BASKETS
Always use the whole space of the baskets.
Only use the appliance to wash items that are
dishwasher-safe.
Do not wash in the appliance items made of
wood, horn, aluminium, pewter and copper as
they could crack, warp, get discoloured or
pitted.
Do not wash in the appliance items that can
absorb water (sponges, household cloths).
Remove remaining food from the items.
Make soft the remaining burned food on the
items.
Put hollow items (cups, glasses and pans) with
the opening down.
Make sure that cutlery and dishes do not bond
together. Mix spoons with other cutlery.
Make sure that glasses do not touch other
glasses.
Put small items in the cutlery basket.
Put light items in the upper basket. Make sure
that the items do not move.
Make sure that the spray arm can move freely
before you start a programme.
BEFORE STARTING A PROGRAMME
Before you start the selected programme, make
sure that:
12
The filters are clean and correctly installed.
The cap of the salt container is tight.
The spray arms are not clogged.
There is enough salt and rinse aid (unless you
use multi-tablets).
The arrangement of the items in the baskets is
correct.
The programme is suitable to the type of load
and the degree of soil.
The correct quantity of detergent is used.
UNLOADING THE BASKETS
1. Let the tableware cool down before you
remove it from the appliance. Hot items can be
easily damaged.
2. First remove items from the lower basket, then
from the upper basket.
After the programme is completed,
water can still remain on the inside
surfaces of the appliance.
CARE AND CLEANING
WARNING! Before maintenance,
deactivate the appliance and
disconnect the mains plug from the
main socket.
Dirty filters and clogged spray arms
decrease the washing results. Make a
check regularly and, if necessary, clean
them.
CLEANING THE FILTERS
B
A
C
Make sure that there are no residues of food or soil in or around the edge of the sump.
Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides.
Reassemble the filters (A) and (B).
Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks.
An incorrect position of the filters can cause bad washing results and damage to the
appliance
13
CLEANING THE SPRAY ARMS
Do not remove the spray arms. If the holes in the
spray arms are clogged, remove remaining parts of
soil with a thin pointed object.
EXTERNAL CLEANING
Clean the appliance with a moist soft cloth.
Only use neutral detergents.
Do not use abrasive products, abrasive cleaning
pads or solvents.
INTERNAL CLEANING
Carefully clean the appliance, including the
rubber gasket of the door, with a soft damp
cloth.
If you regularly use short duration programmes,
these can leave deposits of grease and
limescale inside the appliance. To prevent this,
we recommend to run long duration
programmes at least 2 times per month.
To maintain the performance of your appliance
at its best, we recommend to use monthly a
specific cleaning product for dishwashers.
Follow carefully the instructions on the
packaging of the product.
REMOVAL OF FOREIGN OBJECTS
Check the filters and the sump after each use of the
dishwasher. Foreign objects (e.g. pieces of glass,
plastic, bones or toothpicks, etc) decrease the
cleaning performance and can cause damage to
the drain pump.
1. Disassemble the filters system as instructed in
this chapter.
2. Remove any foreign objects by hand.
CAUTION! If unable to remove the
objects, contact an Authorised
Service Centre.
3. Reassemble the filters as instructed in this
chapter.
TROUBLESHOOTING
WARNING! Improper repair of the
appliance may pose a danger to the
safety of the user. Any repairs must be
performed by qualified personnel.
The majority of problems that can occur can
be solved without the need to contact an
Authorised Service Centre.
Refer to the below table for information on possible
problems.
With some problems, the dedicated indicator
flashes intermittently to indicate a malfunction and
the alarm code.
Problem and alarm code Possible cause and solution
You cannot activate the appliance. Make sure that the mains plug is connected to the
mains socket.
Make sure that there is no damaged fuse in the fuse
box.
The programme does not start. Make sure that the appliance door is closed.
Press the start button.
If the delay start is set, cancel the setting or wait for
the end of the countdown.
The appliance recharges the resin inside the water
softener. The duration of the procedure is approxi-
mately 5 minutes.
14
Problem and alarm code Possible cause and solution
The appliance does not fill with water.
The indicator flashes 1 time inter-
mittently.
The light related to the start button
flashes continuously.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is
not too low. For this information, contact your local
water authority.
Make sure that the water tap is not clogged.
Make sure that the filter in the inlet hose is not clog-
ged.
Make sure that the inlet hose has no kinks or bends.
The appliance does not drain the water.
The indicator flashes 2 times in-
termittently.
The light related to the start button
flashes continuously.
Make sure that the sink spigot is not clogged.
Make sure that the interior filter system is not clog-
ged.
Make sure that the drain hose has no kinks or
bends.
The anti-flood device is on.
The indicator flashes 3 times in-
termittently.
The light related to the start button
flashes continuously.
Close the water tap.
Make sure that the appliance is correctly installed.
Make sure the baskets are loaded as instructed in
the user manual.
Malfunction of the water level detection
sensor.
The indicator flashes 4 times in-
termittently.
The light related to the start button
flashes continuously.
Make sure that the filters are clean.
Switch the appliance off and on.
Malfunction of the wash pump or the drain
pump.
The indicator flashes 5 times in-
termittently.
The light related to the start button
flashes continuously.
Switch the appliance off and on.
The temperature of the water inside the
appliance is too high or malfunction of the
temperature sensor occurred.
The indicator flashes 6 times in-
termittently.
The light related to the start button
flashes continuously.
Make sure that the temperature of the inlet water
does not exceed 60°C.
Switch the appliance off and on.
Technical malfunction of the appliance.
The indicator flashes 12 times in-
termittently.
The light related to the start button
flashes continuously.
Switch the appliance off and on.
15
Problem and alarm code Possible cause and solution
The level of water inside the appliance is
too high.
The indicator flashes 15 times in-
termittently.
The light related to the start button
flashes continuously.
Switch the appliance off and on.
Make sure that the filters are clean.
Make sure that the outlet hose is installed at the
right height above the floor. Refer to the installation
instructions.
The appliance stops and starts more
times during operation.
It is normal. It provides optimal cleaning results and
energy savings.
The programme lasts too long. If the delayed start option is set, cancel the delay
setting or wait for the end of the countdown.
Small leak from the appliance door. The appliance is not levelled. Loosen or tighten the
adjustable feet (if applicable).
The appliance door is not centred on the tub. Adjust
the rear foot (if applicable).
The appliance door is difficult to close. The appliance is not levelled. Loosen or tighten the
adjustable feet (if applicable).
Parts of the tableware are protruding from the bas-
kets.
Rattling/knocking sounds from inside the
appliance.
The tableware is not properly arranged in the bas-
kets. Refer to basket loading leaflet.
Make sure that the spray arms can rotate freely.
The appliance trips the circuit-beaker. The amperage is insufficient to supply simultaneous-
ly all the appliances in use. Check the socket am-
perage and the capacity of the meter or turn off one
of the appliances in use.
Internal electrical fault of the appliance. Contact an
Authorised Service Centre.
Refer to "Before first use", "Daily
use", or "Hints and tips" for other
possible causes.
Once you have checked the appliance, press the
start button. If the problem occurs again, contact
an Authorised Service Centre.
For alarm codes not described in the table, contact
an Authorised Service Centre.
WARNING! We do not recommend
using the appliance until the problem
has been completely fixed. Unplug the
appliance and do not plug it in again
until you are certain that it operates
correctly.
16
THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY
Problem Possible cause and solution
Poor washing results. Refer to "Daily use", "Hints and tips" and basket loading
leaflet.
Use more intensive washing programmes.
Clean spray arm jets and filter. Refer to "Care and Clean-
ing".
Poor drying results. Tableware has been left for too long inside a closed appli-
ance.
There is no rinse aid or the dosage of rinse aid is not enough.
Set the rinse aid dispenser to a higher level.
Plastic items may need to be towel dried.
For the best drying performance activate AirDry.
We recommend to always use rinse aid, even in combination
with multi-tablets.
There are whitish streaks or blu-
ish layers on glasses and dishes.
The release quantity of rinse aid is too much. Adjust the rinse
aid level to a lower level.
The quantity of detergent is too much.
There are stains and dry water
drops on glasses and dishes.
The released quantity of rinse aid is not sufficient. Adjust the
rinse aid level to a higher level.
The quality of the rinse aid can be the cause.
The dishes are wet. For the best drying performance activate AirDry.
The programme does not have a drying phase or has a drying
phase with low temperature.
The rinse aid dispenser is empty.
The quality of the rinse aid can be the cause.
The quality of the multi-tablets can be the cause. Try a differ-
ent brand or activate the rinse aid dispenser and use rinse
aid and multi-tablets together.
The interior of the appliance is
wet.
This is not a defect of the appliance. it is caused by the hu-
midity in the air that condenses on the walls.
Unusual foam during washing. Use the detergent for dishwashers only.
There is a leak in the rinse aid dispenser. Contact an Author-
ised Service Centre.
Traces of rust on cutlery. There is too much salt in the water used for washing. Refer to
"The water softener".
Silver and stainless steel cutlery were placed together. Avoid
to put silver and stainless steel items close together.
There are residues of detergent
in the dispenser at the end of the
programme.
The detergent tablet got stuck in the dispenser and therefore
was not completely washed away by water.
Water cannot wash away the detergent from the dispenser.
Make sure that the spray arm is not blocked or clogged.
Make sure that items in the baskets do not impede the lid of
the detergent dispenser from opening.
Odours inside the appliance. Refer to "Internal cleaning".
17
Problem Possible cause and solution
Limescale deposits on the table-
ware, on the tub and on the in-
side of the door.
The level of salt is low, check the refill indicator.
The cap of the salt container is loose.
Your tap water is hard. Refer to "The water softener".
Even using multi-functional tabs use salt and set regeneration
of the water softener. Refer to "The water softener".
If lime scale deposits still remain, clean the appliance with
appliance cleaners which are particularly suitable for this pur-
pose.
Try different detergent.
Contact the detergent manufacturer.
Dull, discoloured or chipped ta-
bleware.
Make sure that only dishwasher-safe items are washed in the
appliance.
Load and unload the basket carefully. Refer to basket loading
leaflet.
Place delicate items in the upper basket.
Refer to "Before first use", "Daily
use" or "Hints and tips" for other
possible causes.
TECHNICAL INFORMATION
Dimensions Width / height / depth (mm) 596 / 818 - 898 / 575
Electrical connection
1) Voltage (V) 220 - 240
Frequency (Hz) 50
Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)
Water supply
Cold water or hot water
2) max 60 °C
Capacity Place settings 13
Power consumption Left-on mode (W) 5.0
Off-mode (W) 0.50
1) Refer to the rating plate for other values.
2) If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to
decrease energy consumption.
LINK TO THE EU EPREL DATABASE
The QR code on the energy label supplied with the
appliance provides a web link to the registration of
this appliance in the EU EPREL database. Keep
the energy label for reference together with the
user manual and all other documents provided with
this appliance.
It is possible to find information related to the
performance of the product in the EU EPREL
database using the link https://eprel.ec.europa.eu
and the model name and product number that you
can find on the rating plate of the appliance. Refer
to the chapter "Product description".
For more detailed information about the energy
label, visit www.theenergylabel.eu.
18
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
19
VISITEZ NOTRE SITE WEB POUR :
Obtenir des conseils d'utilisation, des brochures, un dépanneur, des informations sur le
service et les réparations :
www.zanussi.com/support
INFORMATIONS DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez soigneusement les
instructions fournies. Le fabricant ne pourra être tenu pour
responsable des blessures et dégâts résultant d'une mauvaise
installation ou utilisation. Conservez toujours les instructions dans
un lieu sûr et accessible pour vous y référer ultérieurement.
SÉCURITÉ DES ENFANTS ET DES PERSONNES
VULNÉRABLES.
Cet appareil peut être utilisé par des enfants âgés d'au moins
8 ans et par des personnes ayant des capacités physiques,
sensorielles ou mentales réduites ou dénuées d’expérience ou
de connaissance, s'ils sont correctement surveillés ou si des
instructions relatives à l'utilisation de l'appareil en toute sécurité
leur ont été données et s’ils comprennent les risques encourus.
Les enfants entre 3 et 8 ans et les personnes ayant un
handicap très important et complexe doivent être tenus à l'écart
de l'appareil, à moins d'être surveillés en permanence.
Les enfants de moins de 3 ans doivent être tenus à l'écart de
l'appareil, à moins d'être surveillés en permanence.
Ne laissez pas les enfants jouer avec l'appareil.
Ne laissez pas les détergents à la portée des enfants.
Tenez les enfants et les animaux éloignés de l'appareil lorsque
la porte est ouverte.
Le nettoyage et l'entretien ne doivent pas être effectués par des
enfants sans surveillance.
SÉCURITÉ GÉNÉRALE
Cet appareil est conçu uniquement pour un usage domestique
et des situations telles que :
bâtiments de ferme, cuisines réservées aux employés dans
les magasins, bureaux et autres lieux de travail ;
20
1 / 1

Zanussi ZDI22003XA Manuel utilisateur

Catégorie
Lave-vaisselle
Taper
Manuel utilisateur

dans d''autres langues