Skil CB7489B-20 Le manuel du propriétaire

Marque: Skil

Modèle: CB7489B-20

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

IW5739-1A

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

20V Brushless Impact Wrench

Clé à chocs sans balai de 20 V

Llave de impacto sin escobillas de 20 V

1-877-SKIL-999

www.skil.com

Model/ Modelo/ Modèle: IW5739-00

TABLE OF CONTENTS

General Power Tool Safety Warnings .............................3-5

Safety Warnings for Impact Wrench ................................5

Symbols .....................................................6-9

Get to Know Your Impact Wrench .................................10

Specications .................................................10

Operating Instructions .......................................11-15

Maintenance ...................................................16

Trouble Shooting ...............................................16

Limited Warranty of Skil Cordless Tool .............................17

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

General Power Tool Safety Warnings

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool.

Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit

. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool.

Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools.

Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply.

Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs,

alcohol or medication.

A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection.

Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energising power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on.

A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.

This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing

away from moving parts.

Loose clothes, jewellery or long hair can be caught in moving

parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used.

Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles.

A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application.

The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off.

Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools.

Such preventive safety measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool.

Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed.

Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery

handles and grasping surfaces do not allow for safe handling and control of the tool in

unexpected situations.

Battery tool use and care

Recharge only with the charger specied by the manufacturer

. A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specically designated battery packs.

Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another

. Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek

medical help

. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modied

. Damaged or modied

batteries may exhibit unpredictable behaviour resulting in re, explosion or risk of injury.

Do not expose a battery pack or tool to re or excessive temperature

. Exposure to re or

temperature above 265 °F may cause explosion.

Follow all charging instructions and do not charge the battery pack or tool outside the

temperature range specied in the instructions.

Charging improperly or at temperatures

outside the specied range may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service providers.

SAFETY WARNINGS FOR IMPACT WRENCH

Hold the power tool by insulated gripping surfaces, when performing an operation

where the fastener may contact hidden wiring.

Fasteners contacting a “live” wire may

make exposed metal parts of the power tool “live” and could give the operator an electric

shock.

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner's

Manual, including all safety alert symbols such as “

DANGER

,”

“

WARNING

,” and “

CAUTION

” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE:

Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in

foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always use

eye protection which is marked to comply with ANSI Z87.1.

SYMBOLS (CONTINUED)

IMPORTANT:

Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

No-load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or

reciprocations per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II tool

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Symbol Name Designation/Explanation

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

Read manual symbol Alerts user to read manual

Wear eye protection symbol

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT:

Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

GET TO KNOW YOUR IMPACT WRENCH

20V Brushless Impact Wrench

BRUSHLESS

Mode

Fig. 1

Removable

Belt Clip

1/2" Square

Drive

Direction-of-

Rotation (Forward/

Center-lock/

Reverse) Selector

Soft Grip

Mode-change Button

Variable-Speed

Trigger Switch

LED Light

SPECIFICATIONS

Rated voltage 20V d.c.

Square drive 1/2"

No-load speed 0~2100/0~2400/min

Impacts per minute 0~2800/0~3200 /min

Recommended working temperature 14~104°F (-10~40℃)

Recommended storage temperature 32~104°F (0~40℃)

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due to a

short circuit, never immerse your tool, battery pack or charger in uid

or allow a uid to ow inside them.

Corrosive or conductive uids, such as seawater, certain

industrial chemicals, and bleach or bleach-containing products, etc, can cause a short circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced.

Use of this product with damaged or missing parts

could result in serious personal injury.

WARNING

Do not attempt to modify this Impact Wrench or create accessories

not recommended for use with this Impact Wrench.

Any such alteration

or modication is misuse and could result in a hazardous condition leading to possible serious

injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the Impact Wrench when

assembling parts, making adjustments, cleaning, or performing maintenance.

This cordless impact wrench must be used only with the battery packs and chargers listed

below:

Battery pack

Charger

2Ah 2Ah 2.5Ah 4Ah 5Ah

SKIL

BY519701

SKIL

BY519702

SKIL

BY519703

SKIL

BY519601

SKIL

BY519603

SKIL

SC535801

SKIL

QC536001

NOTICE:

Please refer to the battery and charger manual for detailed operating information.

To Attach/Detach Battery Pack

(Fig.2)

Lock the trigger switch “OFF” on the tool by

placing the direction-of-rotation (forward/cen-

ter-lock/reverse) selector in the center position

before attaching or detaching the battery pack.

To attach the battery pack:

Align the raised rib on the battery pack with the

grooves of the tool, and then slide the battery

pack onto the tool.

NOTICE:

Make sure that the latch on the

battery pack snaps into place and that the

battery pack is secured to the tool before

beginning operation.

To detach the battery pack:

Depress the battery-release button located on the front of the battery pack to release the bat-

tery pack. Pull the battery pack out and remove it from the tool.

NOTICE:

When placing the battery pack onto the tool, be sure that the raised rib on the

battery pack aligns with the groove inside the tool and that the latches snap into place

properly. Improper attachment of the battery pack can cause damage to internal components.

WARNING

Battery tools are always in operating condition. Therefore, the

direction-of-rotation (forward/center-lock/reverse) selector should

always be locked in center position when not in use or carrying at your side.

BRUSHLESS

Mode

Fig. 2

Attach

Battery-Release Button

Detach

Direction-of-Rotation (Forward/Center-Lock/Reverse) Selector

WARNING

After tool use, lock the direction-of-rotation selector in the

“OFF”position (center-lock) to help prevent accidental starts and

possible injury.

Your tool is equipped with a direction-of-rotation selector, located above the trigger switch.

This selector is used to change the direction of rotation of the bit and to lock the variable-

speed trigger in the “OFF” (center-lock) position (Fig. 3).

a. Position the direction-of-rotation selector to the far right of the tool for forward rotation.

b. Position the direction-of-rotation selector to the far left of the tool for reverse rotation.

c. Setting the switch in “OFF” (center-lock) position helps to reduce the possibility of accidental

starting when not in use.

NOTICE

: To prevent gear damage, always allow the impact wrench to come to a complete

stop before changing the direction of rotation.

NOTICE

: The impact wrench will not run unless the direction-of-rotation selector is engaged

fully to the left or right.

Fig. 3

Forward

ReverseCenter-Lock

Variable-Speed Trigger Switch

Your tool is equipped with a variable-speed

trigger switch. The tool can be turned “ON” or

“OFF” by depressing or releasing the variable-

speed trigger switch.

The variable-speed trigger switch delivers

higher speed with increased trigger pressure

and lower speed with decreased trigger

pressure (Fig. 4).

BRUSHLESS

Fig. 4

Variable Speed

Trigger Switch

Changing the Impact Force (Fig.5)

a. When the tool rotates clockwise (forward

direction), you can change the impact force

between two modes:

LO Mode

HI Mode.

This allows a tightening force suitable to the

work. Every time the mode-change button is

pressed, the number of mode progresses in

order, as follows:

LO Mode

HI Mode

HI Mode.

•

Indicator light 1 shines green for “LO Mode” to indicate “low-speed mode”.

•

Both indicator light 1 and indicator light 2 shine green for “HI Mode” to indicate “high-speed

mode”.

•

Indicator light 3 shines green to indicate “high-speed mode”, which is same to the HI Mode.

b. When the tool rotates counterclockwise (reverse direction), you can change the impact force

among three modes:

LO Mode

HI Mode

Reverse Control Mode.

Every time the mode-change button is pressed, the mode progresses in order, as follows:

LO Mode

HI Mode

Reverse Control Mode.

•

Indicator light 1 shines green for “LO Mode” to indicate “low-speed mode”.

•

Both indicator light 1 and indicator light 2 shine green for “HI Mode” to indicate “high-speed

mode”.

•

Indicator light 3 shines green to indicate “reverse control mode”.

In reverse control mode, the tool stops the reverse rotation and the impact within seconds

once the fastener is loosened.

NOTICE:

The reverse control mode is available only when the tool rotates counterclockwise

and the trigger switch is fully depressed.

NOTICE:

The impact force mode can be changed only when any mode-indicator light is

shining and the trigger switch is not depressed. The impact force mode cannot be activated

when the motor is running.

The impact force mode will be stored and applied in the next operation when the tool is turned

on again or when the direction of rotation has been changed. Reset the impact modes as

desired.

When the trigger is squeezed slightly, one of the three indicator lights will automatically shine

green, to indicate the force mode stored at the last use and will turn off approximately 60

seconds after the variable speed trigger switch is released. It means that during approximately

one minute after releasing the switch trigger, the impact force can be changed.

1 2 3

1 2

Fig. 5

Impact force mode

displayed

Maximum IPM

(Impacts per minute)

Purpose

Example of

application

High 3200 min

-1

(/min)

Tightening when

force and speed are

desired.

Assembling steel

frames

Low 2800 min

-1

(/min)

Tightening when you

need ne adjustment

with small diameter

bolt.

Assembling furnitures

Reverse Control

Mode

3200 min

-1

(/min)

Loosening with

automatic control.

Disassembling nuts

or bolts.

LED Light

Your tool is equipped with an LED light, located

on the base of the tool. This provides additional

light on the surface of the work piece for

operation in lower-light areas.

The LED light will automatically turn on with a

slight squeeze on the variable-speed trigger

switch before the tool starts running, and will

turn off approximately 10 seconds after the

variable-speed trigger switch is released.

The LED light will rapidly ash when the tool

and/or battery pack becomes overloaded or

too hot, and the internal sensors will turn the

tool off. Rest the tool for a while or place the

tool and battery pack separately under air ow

to cool them.

The LED light will ash more slowly to indicate that the battery is at low-battery capacity.

Recharge the battery pack.

Removable Belt Clip (Fig.7)

Your tool is equipped with removable belt clip,

which can be positioned on the left side of the

tool for convenient transport.

Install the belt clip onto the tool:

a. Remove the battery pack from the tool.

b. Align the rib of the belt clip with the threaded

hole on the base of the tool.

c. Insert the screw and securely tighten the

screw with a screwdriver.

Remove the belt clip from the tool:

d. Remove the battery pack from the tool.

e. Use a screwdriver to loosen the screw that

attaches the belt clip to the impact wrench.

f. Remove the screw and the belt clip.

BRUSHLESS

Fig. 6

BRUSHLESS

Mode

Fig. 7

Install and Remove the Impact

Socket (Fig.8)

Lock the trigger switch “OFF” by placing the

direction-of-rotation selector in the center

position.

CAUTION:

Make sure that the impact socket

and the mounting portion are not damaged

before installing the impact socket.

To install the Impact Socket:

a. Align the square of the impact socket with

the square drive and push the impact socket

onto the square drive until it locks into place.

b. Tap it lightly if required.

Remove the Impact Socket:

To remove the impact socket, simply pull it off.

WARNING

Use protective gloves when removing the impact socket from the tool, or

rst allow the impact socket to cool down. The impact socket may be hot

after prolonged use.

Tighten and loosen nuts and bolts

Variable speed control must be used with caution for driving nuts and bolts with socket set

attachments. The technique is to start slowly, increasing speed as the nut or bolt runs downs.

Set the nut or bolt snugly by slowing the tool to a stop. If this procedure is not followed, the

tool will have a tendency to torque or twist in your hands when the nut or bolt seats.

a. Select hex socket that matches the nut or bolt. Then mount the socket on the square drive,

and grip the nut or bolt to be tightened with the hex socket.

b. Hold the tool rmly and apply just enough pressure to keep the socket engaged on the nut

or bolt. Then press the trigger switch to impact the nut or bolt for several seconds.

NOTICE:

Always use the correct size impact socket for bolts and nuts. An incorrect size

impact socket will result in inaccurate and inconsistent fastening torque and/or damage to the

bolt or nut.

WARNING

Do not over-tighten, as the force of the impact tool can break the fastener.

Hold the tool vertical with the bolt or nut, otherwise the head of the bolt or

nut will be damaged.

Fig. 8

Square

Drive

Impact

Socket

MAINTENANCE

WARNING

To avoid serious personal injury, always remove the battery pack

from the tool when cleaning or performing any maintenance.

Service

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing of internal wires and components which could

cause serious hazard.

We recommend that all tool service be performed by a Skil Factory

Service Center or Authorized Skil Service Station.

General Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any other

parts could create a hazard or cause product damage.

NOTE:

Periodically inspect the entire product for damaged, missing, or loose parts such as

screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this

product until all missing or damaged parts are replaced. Please contact customer service or

an authorized service center for assistance.

Cleaning

WARNING

The tool may be cleaned most effectively with compressed dry air.

Always

wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not

attempt to clean by inserting pointed objects through openings.

WARNING

Certain cleaning agents and solvents damage plastic parts.

Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and house hold detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive

agents.

TROUBLE SHOOTING

Problem Cause Remedy

Tool will not start. 1. Battery pack is depleted. 1. Charge the battery.

2. Tool is over-loaded. 2. Release the variable-speed trigger

switch and try again.

3. Battery pack is over

temperature.

3. Turn off the impact wrench and cool

the battery pack under air ow.

4. Battery pack is not installed

properly.

4. Conrm that the battery is locked

and secured to the tool.

5. Burned out switch. 5. Have the switch replaced by an

Authorized SKIL Service Center or

Service Station.

LED light rapidly

ashes.

1. Tool is over-loaded. 1. Release the trigger switch.

2. Tool is over-temperature. 2. Cool the tool under air ow.

LIMITED WARRANTY FOR SKIL CORDLESS TOOL

5 YEARS LIMITED WARRANTY

Chervon North America, Inc. (“Seller”) warrants to the original purchaser only, that all SKIL

consumer POWER TOOLS will be free from defects in material or workmanship for a period

of ve years from date of purchase, if original purchaser registers the product within 30 days

from purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration

can be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR POWER

TOOLS IS CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF

PURCHASE. If original purchasers do not register their product timely, the foregoing limited

warranty will apply for a duration of three years for power tools. All batteries and chargers will

remain under the two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer portable power tool is used for industrial,

professional or commercial purposes, the foregoing warranty will apply for a duration of ninety

days, regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,

please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING

BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME STATES

IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO

YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

08/19

TABLE DES MATIÈRES

Avertissements de sécurité généraux relatifs

aux outils électriques ........................................19-21

Avertissem ents relatifs à la sécurité pour les clés à chocs ............21

Symboles ..................................................22-25

Familiarisez-vous avec votre clé à chocs ...........................26

Caractéristiques techniques .....................................26

Mode d’emploi ..............................................27-32

Entretien ......................................................33

Recherche de la cause des problèmes .............................34

Garantie limitée de l’outil sans l SKIL ..........................35-36

AVERTISSEMENT

•

La poussière créée pendant le ponçage, le sciage, le polissage, le perçage et d’autres acti-

vités liées à la construction peut contenir des produits chimiques reconnus par l’État de la

Californie comme étant la cause de cancers, d’anomalies congénitales et d’autres problèmes

liés aux fonctions reproductrices. Voici des exemples de ces produits chimiques :

–

Plomb provenant de peintures à base de plomb.

–

Silice cristallisée contenue dans les briques, le ciment et d’autres produits de maçonnerie.

–

Arsenic et chrome contenus dans le bois d’œuvre traité avec des produits chimiques.

•

Les risques liés à l’exposition à ces produits va-rient selon le nombre de fois où vous

pratiquez ces activités. Pour réduire votre exposition à ces produits chimiques :

–

travaillez dans un endroit bien ventilé;

–

munissez-vous de l’équipement de sécurité ap-prouvé tel que des masques antipoussières

conçus spécialement pour ltrer les particules microscopiques;

–

évitez l’exposition prolongée à la poussière causée par le ponçage mécanique, le sciage,

le polissage, le perçage et d’autres activités liées à la construction. Portez un équipement

de pro-tection et lavez à l’eau et au savon toutes les parties exposées. Les poussières

pénétrant dans votre bouche ou dans vos yeux et les poussières se déposant sur votre peau

peuvent causer l’absorption de produits chimiques dangereux.

Avertissements De Sécurité Généraux Relatifs Aux Outils

Électriques

AVERTISSEMENT

Lisez tous les avertissements et toutes les ins-tructions,

illustrations et spécications fournis avec cet outil

électrique.

Le non-respect des consignes de sécurité ci-dessous peut occasionner un choc

électrique, un in-cendie ou des blessures graves.

CONSERVEZ TOUS LES AVERTISSEMENTS ET TOUTES

LES INSTRUCTIONS AFIN DE POUVOIR LES CON-SULTER

ULTÉRIEUREMENT.

L’expression « outil électrique » utilisée dans les avertissements correspond aux outils

électriques alimentés sur secteur (à l) ou alimentés par piles (sans l).

Mesures de sécurité dans l’aire de travail

Maintenez l’aire de travail propre et bien éclairée.

Les aires de travail sombres et en-

combrées sont propices aux accidents.

N’utilisez pas d’outils électriques dans un en-droit présentant un risque d’explosion,

par exemple en présence de liquides, de gaz ou de poussières inam-mables.

Les outils

électriques produisent des étincelles pouvant causer un incendie en raison de la poussière et

des fumées.

Gardez les enfants et les autres personnes à l’écart lorsque vous utilisez un outil

électrique.

Une distraction peut vous faire perdre la maîtrise de l’outil.

Consignes de sécurité relatives à l’électricité

Les ches des outils électriques doivent cor-respondre à la prise. Ne modiez jamais

la che de quelque façon que ce soit. N’utilisez pas d’adaptateur avec les outils

électriques mis à la terre.

L’utilisation de ches non modiées dans les prises compatibles

réduit les risques de choc électrique.

Évitez de toucher à des surfaces mises à la terre, par exemple, un tuyau, un radiateur,

une cuisi-nière ou un réfrigérateur.

Le contact du corps avec une surface mise à la terre

augmente les risques de choc électrique.

N’exposez pas les outils électriques à la pluie ni à tout environnement humide.

L’inltration d’eau dans un outil électrique augmente les risques de choc électrique.

N’utilisez pas le cordon d’alimentation de façon à l’endommager. Ne transportez jamais

un outil électrique en le tenant par son cordon, et ne tirez jamais sur le cordon pour le

débrancher. Tenez le cordon d’alimentation éloigné des sources de chaleur, de l’huile,

des objets cou-pants et des pièces mobiles.

Les risques de choc électrique sont plus

élevés si le cordon d’alimentation est endommagé ou emmêlé.

Lorsque vous utilisez un outil électrique à l’extérieur, utilisez une rallonge conçue pour

être utilisée à l’extérieur.

Ce type de rallonge réduit les risques de choc électrique.

Si vous n’avez d’autre choix que d’utiliser un outil électrique dans un endroit humide,

utilisez une alimentation protégée par un disjoncteur différentiel.

L’utilisation d’un

disjoncteur dif-férentiel réduit les risques de choc électrique.

Sécurité personnelle

Soyez vigilant, prêtez attention à ce que vous faites et usez de votre jugement lorsque

vous utilisez un outil électrique. N’utilisez pas un outil électrique lorsque vous êtes

fatigué ou sous l’effet de drogues, d’alcool ou de médicaments.

Un moment d’inattention

lorsque vous utilisez des outils électriques peut occasionner des blessures graves.

Utilisez un équipement individuel de protec-tion.

Portez toujours des lunettes de sécurité.

Le port d’équipement de protection, comme un masque antipoussières, des chaussures de

sécu-rité antidérapantes, un casque de protection et des protecteurs auditifs, lorsque les

conditions l’exigent, réduit les risques de blessures.

Prenez des mesures an d’éviter que l’outil se mette en marche accidentellement.

Assu-rez-vous que l’interrupteur est à la position d’arrêt avant de brancher l’outil sur

une source d’alimentation ou un bloc-piles, de ramasser l’outil ou de le transporter.

Transporter les outils électriques avec le doigt sur la gâchette ou brancher les outils lorsque

l’interrupteur est à la position de marche augmente les risques d’accident.

Retirez toutes les clés de réglage de l’outil électrique avant de mettre celui-ci en

marche.

Une clé de réglage oubliée sur une pièce rotative de l’outil électrique peut

occasionner des blessures graves.

Ne vous étirez pas pour étendre votre portée.

Gardez une posture sécuritaire et un bon

équi-libre en tout temps. Cela vous permet de mieux maîtriser l’outil électrique lorsque des

situations inattendues se présentent.

Habillez-vous convenablement. Ne portez pas de vêtements amples ni de bijoux.

Gardez vos cheveux, vos vêtements et vos gants loin des pièces mobiles.

Les

vêtements amples, les bijoux et les cheveux longs risquent de se prendre dans les pièces en

mouvement.

Si un dispositif permet de raccorder un dé-poussiéreur, assurez-vous que celui-ci

est branché et utilisé correctement.

L’emploi d’un dépoussiéreur contribue à réduire les

dangers liés à la pous-sière.

Restez toujours sur vos gardes et suivez les principes de sécurité des outils, même s’il

s’agit d’un outil que vous utilisez fréquemment.

Il suft d’être négligent une fraction de

seconde pour se blesser gravement.

Utilisation et entretien d’un outil électrique

Ne forcez pas l’outil électrique. Utilisez l’outil électrique approprié à la tâche que

vous sou-haitez accomplir.

L’utilisation de l’outil élec-trique approprié permet d’obtenir de

meilleurs résultats, de façon plus sécuritaire, selon le ré-gime de fonctionnement prévu.

N’utilisez pas l’outil électrique si l’interrupteur ne fonctionne pas.

Tout outil électrique qui

ne peut être commandé au moyen de l’interrupteur est dangereux et doit être réparé.

Débranchez la che de la prise ou retirez, si possible, le bloc-piles de l’outil électrique

avant d’effectuer des réglages, de changer d’accessoire ou de le ranger.

Ces mesures

de sécurité pré-ventives réduisent les risques de mise en marche accidentelle de l’outil

électrique.

Rangez les outils électriques inutilisés hors de la portée des enfants et ne laissez

pas les personnes ne connaissant pas bien l’outil ou ces instruc-tions utiliser l’outil.

Les outils électriques sont dangereux s’ils se retrouvent entre les mains d’utilisateurs qui ne

savent pas s’en servir.

Entretenez vos outils électriques et vos acces-soires. Vériez les pièces mobiles pour

vous assurer qu’elles ne sont pas désalignées, en-rayées, brisées, ou dans un état

qui pourrait nuire à leur fonctionnement. Si l’outil électrique est endommagé, faites-le

réparer avant de l’utiliser.

De nombreux accidents sont provo-qués par des outils électriques

mal entretenus.

Gardez vos outils tranchants affûtés et propres.

Des outils tranchants bien entretenus dont

les lames sont affûtées risquent moins de se bloquer et sont plus faciles à maîtriser.

Utilisez l’outil électrique, les accessoires, les embouts et les autres éléments

conformément aux présentes instructions, en tenant compte des conditions de travail

et du travail à effectuer.

L’utilisation de l’outil électrique à des ns autres que celles pour

lesquelles il a été conçu pourrait créer une situation dangereuse.

La page charge ...

Skil CB7489B-20 Le manuel du propriétaire

Marque: Skil

Modèle: CB7489B-20

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

IW5739-1A

Télécharger le PDF

rapport

dans d''autres langues

English: Skil CB7489B-20 Owner's manual
español: Skil CB7489B-20 El manual del propietario

Skil CB7489B-20 Le manuel du propriétaire

Ce manuel convient également à

Skil CB7489B-20 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents