Sanyo SPW-W366HH58 Installation Instructions Manual

Marque: Sanyo

Modèle: SPW-W366HH58

Catégorie: Climatiseurs split-system

Taper: Installation Instructions Manual

Ce manuel convient également à

INSTALLATION INSTRUCTIONS

NOTICE D’INSTALLATION

Pub. ??.????.???.?

SANYO 2009

SPW-W486HH58

SPW-W366HH58

SPW-W606HH58

Inverter split air to water heat pump - Indoor unit

Pompe à chaleur air / eau split inverter - Unité intérieure

(Name Plate)

IMPORTANT!

Please read before installation

This air conditioning system meets strict safety and operating

standards.

For the installer or service person, it is important to install or

service the system so that it operates safely and ef

ficiently.

For safe installation and trouble-free operation, you must:

• Carefully read this instruction booklet before beginning.

•

Follow each installation or repair step exactly as shown.

• Observe all local, state and national electrical codes.

• Pay close attention to all warning and caution notices given in

this manual.

•The unit must be supplied with a dedicated electrical line.

This symbol refers to a hazard or unsafe practice which can

result in severe personal injury or death.

This symbol refers to a hazard or unsafe practice which can

result in personal injury or product or property damage.

If necessary, get help

These instructions are all you need for most installation sites

and maintenance conditions.

If you require help for a special problem, contact our sale/service

outlet or your certified dealer for additional instructions.

In case of improper installation

The manufacturer shall in no way be responsible for improper

installation or maintenance service, including failure to follow the

instructions in this document.

SPECIAL PRECAUTIONS

• During installation, connect before the refrigerant system and

then the wiring one; proceed in the reverse orden when

removing the units.

When wiring

ELECTRICAL SHOCK CAN CAUSE SEVERE

PERSONAL INJURY OR DEATH. ONLY A

QUALIFIED, EXPERIENCED ELECTRICIANS

SHOULD ATTEMPT TO WIRE THIS SYSTEM.

•

Do not supply power to the unit until all wiring and tubing are

completed or reconnected and checked, to ensure the grounding.

• Highly dangerous electrical voltages are used in this system.

Carefully refer to the wiring diagram and these instructions

when wiring.

Improper connections and inadequate grounding can cause

accidental injury and death.

•

ound the unit

following local electrical codes.

• The Yellow/Green wire cannot be used for any connection

different from the ground connection.

• Connect all wiring tightly. Loose wiring may cause overheating

at connection points and a possible fire hazard.

•

Do not allow wiring to touch the refrigerant tubing,

compressor

, or any moving parts of the fan.

• Do not use multi-core cable when wiring the power supply and

control lines. Use separate cables for each type of line.

When transporting

Be careful when picking up and moving the indoor and outdoor

units. Get a partner to help, and bend your knees when lifting to

reduce strain on your back. Sharp edges or thin aluminium fins

on the air conditioner can cut your fingers.

When installing...

... In a room

Properly insulate any tubing run inside a room to prevent

"sweating", which can cause dripping and water damage to walls

and floors.

... In moist or uneven locations

Use a raised concrete base to provide a solid level foundation

for the outdoor unit.

This prevents damage and abnormal vibrations.

... In area with strong winds

Securely anchor the outdoor unit down with bolts and a metal

frame. Provide a suitable air baffle.

... In a snowy area (for heat pump-type systems)

Install the outdoor unit on a raised platform that is higher than

drifting snow. Provide snow vents.

When connecting refrigerant tubing

• Keep all tubing runs as short as possible.

• Use the flare method for connecting tubing.

• Apply refrigerant lubricant to the matching surfaces of the flare

and union tubes before connecting them; screw by hand and

then tighten the nut with a torque wrench for a leak-free

connection.

• Check carefully for leaks before starting the test run.

NOTE:

Depending on the system type, liquid and gas lines may be

either narrow or wide. Therefore, to avoid confusion, the

refrigerant tubing for your particular model is specified as narrow

tube for liquid, wide tube for gas.

When servicing

• Turn the power OFF at the main power board before opening

the unit to check or repair electrical parts and wiring.

• Keep your fingers and clothing away from any moving parts.

• Clean up the site after the work, remembering to check that no

metal scraps or bits of wiring have been left inside the unit

being serviced.

•

Ventilate the room during the installation or testing the

refrigeration system; make sure that, after the installation, no

gas leaks are present, because this could produce toxic gas

and dangerous if in contact with flames or heat-sources.

WARNING

CAUTION

WARNING

NOTE: This symbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area

of the world.

our product is designed and manufactured with high quality materials and components which can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed separately from your household

waste.

Please dispose of this equipment at your local community waste collection/recycling centre.

In the European Union there are separate collection systems for used electrical and electronic products.

Please help us to conserve the environment we live in!

SUMMARY

1 - GENERALITIES

1.1 - GENERAL SUPPLY CONDITIONS

• Generally speaking, the material is transported at the consignee’s risk.

• The consignee must immediately provide the carrier with written reserves if he finds any damage caused during transport.

1.2 - RECOMMENDATIONS

•

Prior to all servicing or other actions on the equipment, installation, commissioning, operation, or maintenance, the

personnel in charge of these operations shall become familiar with the instructions and recommendations provided in the

installation manual of the unit as well as the elements of the project's technical file.

• The personnel responsible for receiving the unit must conduct a visual inspection in order to identify all damage to which

the unit may have been subjected during transport: refrigerating circuit, electrical cabinet, cassis and cabinet.

• The unit must be installed, started, maintained, serviced by qualified and authorised personnel, in compliance with the

requirements of all directives, laws and regulations and in accordance with standard trade practices.

• During installation, troubleshooting and maintenance operations, the use of pipes as a step: under the stress, the pipe may

rupture and the refrigerant may cause serious burns

1.3 - VOLTAGE

•

Before carrying out any operation, check that the voltage indicated on the unit corresponds to the mains voltage.

• Before initiating maintenance or servicing on the installation, check that its power supply is disconnected and locked out.

1.4 - USE OF EQUIPMENT

• This device is designed for heating buildings.

This appliance is not designed to be used by people (including children) whose physical, sensory or mental

capacities are impaired, or who lack experience or knowledge, unless they are supervised or have received

instructions on how to use the appliance by a person who is responsible for their safety

. Children must be

supervised to ensure that they do not play with the appliance or its accessories.

1.5 - OPERATING CONDITIONS

• Refer to the technical specifications, the nominal conditions and operating limitations in the technical manual.

MARKING

This product marked conforms to the essential requirements of the Directives:

- Low voltage no. 2006/95/EC.

- Electromagnetic Compatibility no. 89/336 EEC, modified 92/31 and 93/68 EEC.

1 - Generalities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 - Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 - Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4 - Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5 - Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6 - Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 - Maintenance instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

8 - Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1 - Only the following indoor units are to be used with the outdoor units indicated below:

Indoor units Outdoor units

SPW-W366HH58 ----> SPW-C366VEH or VEH8 or VEHN

SPW-W486HH58 ----> SPW-C486VEH or VEH8 or VEHN

SPW-W606HH58 ----> SPW-C606VEH or VEH8 or VEHN

- For the installation of the outdoor unit, please consult the manual supplied with the unit.

NOTE

IMPORTANT

1 - Plate type heat exchanger.

2 - Electric heater:

SPW-W336 and 486:

• 4 kW: 1

stage = 2 kW; 2

stage = 2 kW.

• 6 kW: 1

stage = 4 kW; 2

stage = 2 kW.

SPW-W606:

• 6 kW: 1

stage = 3 kW; 2

stage = 3 kW.

• 9 kW: 1

stage = 6 kW; 2

stage = 3 kW.

3 -

Automatic air vent valve.

4 - Water pressostat.

5 - Automatic reset safety thermostat.

6 - Manual reset safety thermostat.

7 - Circulator pump.

8 - Surge tank.

9 - Manual air vent valve.

10 - Hydraulic system pressure gauge.

11 - Safety valve.

12 - Flow detector.

13 - Water inlet connection.

14 - Water outlet connection.

15 - Filling / drainage of the water system.

16 - Safety valve drain connection.

17 - Flare gas connector.

18 - Flare liquid connector.

19 - Electrical cable passage.

20 - Water system pressure tap for flow control.

21 - Cover.

22 - Communication module access window.

23 - Electrical box (see detail below).

2 - PRESENTATION

2.1 - DESCRIPTION

2.1.1 - GENERAL

SPW-W366HH

SPW-W486HH

SPW-W606HH

1 - Electrical cable passage.

2 - Terminal strip.

3 -

Heating element circuit breakers.

4 -

Heating element contactors.

5 - Circulator contactors.

6 - Fault relays.

7 - Water flow rate relay.

8 -

Heating control board.

9 - Communication module CC1.

10 -

Control circuit circuit-breaker

11 - Indoor unit board.

12 - Transformer.

2.1.2 - ELECTRICAL BOX

17 10 18 14 16 11 15 13 19

• Reminder:

Water system pressure: 2 bar

- Operating limits:

20-16 -10

4310

Outdoor dry air

temperature (

°C)

Outdoor dry air

temperature (°C)

ater output

temperature (

°C)

ater output

temperature (

°C)

Materials:

- Copper piping.

- Stainless steel water heat exchanger.

- Painted sheet metal cabinet.

Heating mode Cooling mode

• 1" FF hydraulic filter

• Outside temperature sensor:

- Installed in a box with cable gland.

Note:

This sensor must be installed in

a location that is sheltered from

inclement weather.

See details in paragraph 3.4.

• Control unit:

- Plastic wall-mounted control unit.

- Dimensions: height = 128 mm

width

= 86 mm

depth = 34 mm

- Colour: White

- Class lll

IP 30

2.1.3 - ACCESSORIES INCLUDED WITH THE APPARATUS

2.2 - DIMENSIONS AND WEIGHT

Weight (kg)

SPW-W366HH 42

SPW-W486HH 43

SPW-W606HH 44

1 Water inlet connection 1" (male)

2 Water outlet connection 1" (male)

3 Water circuit fill/drain - 1/2" male

4 Safety valve connection and drainage

5 5/8" gas refrigerant connection

6 3/8" liquid refrigerant connection

7 Holes for electric cables

527

823.5

284

184

246

290.5

352

328.5

392.25

40.5

125

133.5

178

220.5

15.5

4 1 7

6 2 3

3 - INSTALLATION

3.1 - LOCATION

• Protection index of the unit: IP 21.

•

Select the location for the unit on the basis of the following criteria

- the unit must be installed in a sheltered location,

- the unit must not be installed near the following:

sources of heat,

. combustible materials,

return / air intake of an adjacent building.

- it is necessary to make sure that the free space around the unit is

provided (see the minimum dimensions on the drawing opposite),

- installation must be simple and make maintenance work easy,

the unit must be secured to a wall able to support its weight.

3.2 - MOUNTING THE UNIT

• Remove the cover from the unit:

- remove the retaining screws (1 on each side and 1 on top) (1).

•

Slide the cover upward (

2), until the bottom edge of the covers is aligned

with the lower part of the rear support, then pull it towards you (3).

• Secure the unit to the wall. Refer to the position of the 4

mounting holes in the diagram opposite.

Use anchors and screws (not included) that are adapted

to the weight of the unit and the type of wall.

- Install the 2 screws in place in the upper holes (

A) in

the wall.

- Hook the unit in place.

- Install the 2 screws in place in the lower holes (

B).

0.80 m

0.20 m

1 m

800 mm

460 mm

360 mm

Minimum clearance in front of the unit: 1 m

Align the bottom edge of the cover with the

lower part of the rear support

• Replacing the cover.

Present the cover on the unit while aligning the lower

edge with the lower part of the rear support.

Fit the cover against the rear support to engage the

hooks in the notches (

1).

- Slide the cover downward fully into place (2).

- Replace the retaining screws.

Note: the screw (T) on top of the unit ensures the

cover's ground continuity. This is a special screw

and only this model should be used.

. The screw on the left-hand side is used primarily

for transport. In the case of insufficient clearance

(too close to a wall), this screw need not be

replaced.

3.3 - CONTROL UNIT INSTALLATION

• As the control unit is equipped with a temperature sensor, it must be

installed in a location that is representative of the temperature in zone 1.

•

Note: For 2-zone applications, an ambient temperature sensor (zone 1)

(accessory) can be connected on the 2-zone module thus doing away

with the need to install the control unit in zone 1.

• Wall mounting: the unit must not be installed in corners, on shelves or

behind curtains, near sources or heat or directly exposed to sunlight. The

unit should be installed approximately 1.5 m above the floor.

• Open the box by removing the lower screw and secure the base to the

wall (mounting holes, item (

1)).

• Open the protective cover (screw (

2)) and connect the

BUS link to the control board (see diagram in paragraph

4.3.4.).

• Fit the control unit back on its base.

3.4 - INSTALLATION OF THE OUTDOOR

TEMPERATURE SENSOR

•

This sensor must be located outside in a location that is

representative of the temperature to be measured (on a wall

facing North / North-west) and located away from parasitic

heat sources (chimney

, thermal bridge, etc..) and sheltered

from inclement weather (under a roof overhand, for

example).

• Connection as per paragraph 4.3.4.

Bottom of cover

Lower part of

the rear

support

Align

Base

Rear view

1.50 m

Control unit

Mini. 20 cm

4 - CONNECTIONS

4.1 - REFRIGERATION CONNECTIONS

Outdoor unit

Indoor unit

Gas line

Liquid line

Model 366 Model 486 Model 606

3/8” (9.52 mm) 3/8” (9.52 mm) 3/8” (9.52 mm)

5/8” (15.88 mm) 5/8” (15.88 mm) 5/8” (15.88 mm)

3 m 3 m 3 m

10 m 10 m 10 m

30 m 30 m 30m

40 g 40 g 40 g

ø Liquid tube

ø Gas tube

Minimum pipe length

Maximum pipe length without addition of

refrigerant load

Maximum pipe length with addition of refrigerant

load

Additional load per meter

•

For the connecting pipes, use the flare nuts provided with the unit or nuts intended for the R 410

• Connect the units with the connecting tubes in accordance with the table below.

R 410 A

• R 410 A is a high-pressure refrigerant (+ 50% in relation to

R 22 and R 407 C).

• The compressors approved for operation with this fluid are

filled beforehand with polyalcohol oil.

Contrary to mineral oil, it is very hygroscopic: it absorbs the

humidity of the ambient air very quickly. This can modify its

lubricant properties and lead in time to the destruction of the

compressor.

MAINTENANCE INSTRUCTIONS

- Never add oil to the appliance; the compressor is filled

with polyalcohol oil, a special oil which cannot tolerate the

presence of other oils.

2 - The instruments used for:

- filling,

- pressure measurements,

- emptying under vacuum,

- recovering the fluid,

must be compatible and only used for the R 410 A fluid.

Note: the pressure taps of the refrigerating circuit are

5/16 SAE (1/2 - 20 - UNF)

3 - In the case of a new charge:

- the charge must be undertaken in liquid phase,

- use a balance and a dip pipe type R 410 A cylinder,

- charge the weight of R 410 A as per the value indicated

on the unit’s identification plate (for “split systems”, refer

to the installation instructions as the charge must

consider the length of the connecting lines).

4 - In case of leakage, do not complete the charge: recover

the remaining refrigerant for recycling and perform a total

charge.

Recovery, recycling or the destruction of the fluid must be

done in compliance with the laws in force in the country

concerned.

5 - If the refrigerant circuit is opened, you must:

avoid the entry of air into the circuit as much as

possible,

- replace or install a drier,

- perform the “vacuum operation” at a minimum level of

0.3 mbar (static).

6 - Do not release R 410 A fluid into the atmosphere. This

fluid is a fluorinated greenhouse gases, covered by the

Kyoto Protocol with a Global Warming Potential (GWP) =

1975 - (CE Directive 842 / 2006).

APPLIANCES FILLED WITH R 410 A

• For the following information:

Maximum height between units.

- Required tools.

Advice concerning the piping installation.

- Connection to the outdoor unit.

- Leak testing.

- Vacuum operation.

Additional refrigerant charge.

Refer to the installation instructions provided with the outdoor unit.

• For the connection to the indoor unit's flare couplings, use 2 wrenches to

maintain the coupling.

Tighten to the following tightening torque values:

ø 3/8”: 34 - 42 N.m.

- ø 5/8”: 68 - 82 N.m.

4.2 - HYDRAULIC CONNECTION

4.2.1 - WATER INLET AND OUTLET CONNECTION

•

Connect the water inlet and outlet lines to the corresponding

couplings.

• Install the hydraulic filter (1) (supplied) on the water intake. Connect it

using 2 isolation valves (2) (not supplied) for cleaning purposes.

• "Water connection hose" accessories may be used (refer to the

accessories paragraph).

4.2.2 - FILLING / DRAINAGE CONNECTION

• A coupling is available for filling or draining water from the unit.

• To use this connection, install a shut-off valve (

3) (not supplied).

4.2.3 - SAFETY VALVE CONNECTION

• The unit is equipped with a safety valve that opens if the pressure in

the hydraulic system exceeds 3 bar.

A flexible hose (4) (not supplied) can be connected to the coupling

insert (coupling OD: 18 mm).

4.3 - ELECTRICAL CONNECTION

4.3.1 - GENERAL:

• The acceptable voltage variation is: ± 10% during operation.

• The electrical connection conduits must be fixed.

•

Use the cable clamps underneath the unit and route the wires into the electric panel, to the terminal strips.

• Class 1 unit.

• The electrical installation must comply with the standards and regulations applicable where the unit is being installed (in

particular NF C 15-100 ≈ IEC 364).

4.3.2 - POWER SUPPLY

• The power supply must come from an isolation and electric protection device (not supplied) in accordance with existing

regulations.

•

two-pole circuit breaker (not supplied) must be installed to protect single-phase equipment or a three-pole circuit

breaker (not supplied) for three-phase equipment. See the intensity ratings table.

• The power supply is connected to the power terminal strip located inside the indoor unit.

SPW-W units are designed to be supplied with either single-phase 230V or three-phase 400V.

In a three-phase configuration, the jumper between terminals L1, L2, and L3 on terminal strip XA.

Note:

The unit is designed to be connected to a power supply having a

TT neutral regime (neutral to ground) or TN.S regime

(to neutral) as per NF C 15-100.

POWER SUPPLY CABLE

- Section: see amperage table.

- The sections are given as an indication only. They have to be verified and adapted, if necessary, according to the

installation conditions and the standards in force.

CURRENTS AND CROSS-SECTIONS

(*) With 6 kW electric heating module only.

SELECTION OF ELECTRIC HEATING MODULE POWERS

- To obtain the maximum electric heating module power ratings, the jumper must be installed between 22 and 23 on

terminal strip XA (jumper included).

4.3.3 - CONNECTION WITH THE OUTDOOR UNIT

- The control connection between the indoor unit and the outdoor unit is made by a shielded 0.75 mm

cable

(AWG #18), with the shielding grounded at both the indoor unit and outdoor unit side.

Maximum length 70 meters.

The cable's shielding must be grounded at both ends by means of a metal clamp (not supplied) screwed onto the

terminal strip support plate.

To avoid problems related to electromagnetic disturbances, do not route this cable near power cables.

SPW-W366 / SPW-W486 / SPW-W606

N L1 L2 L3

Three-phase power supply

400V / 3+N+T / 50Hz

PE N

Ph1 Ph2 Ph3

erminal

strip XA

SPW-W366 / SPW-W486 / SPW-W606

N L1 L2 L3

Single-phase power supply

230V / 1+T / 50Hz

PE N

Jumper

Terminal

strip XA

Model

SPW-W366

230/1/50

SPW-W366

400/3N/50

SPW-W486

230/1/50

SPW-W486

400/3N/50

SPW-W606

230/1/50 (*)

SPW-W606

400/3N/50

Rated input amperage A

27 9.5 27 9.5 27 14

Protection rating A 32 12 32 12 32 16

Power supply cable size 3G6mm

5G2.5mm

3G6mm

5G2.5mm

3G6mm

5G2.5mm

Model

SPW-W366

single

SPW-W366

three

SPW-W486

single

SPW-W486

three

SPW-W606

single

SPW-W606

three

Jumper between 22 and 23 of

terminal strip XA

no yes no yes no yes no yes no no yes

Electric heating

module powers

(2+2)

(4+2)

(2+2)

(4+2)

(2+2)

(4+2)

(2+2)

(4+2)

6 only

(3+3)

(6+3)

Outdoor Unit

Indoor Unit

Interconnect cable

between the indoor

unit and the outdoor

unit

Shielding

Screws (not supplied)

Metal clamp (not supplied) screwed to

the terminal strip's support plate

Grounding of the

cable shielding:

4.3.4 - OTHER CONTROL CONNECTIONS

Caution:

o avoid problems related to electromagnetic disturbances, do not route these cables near power cables.

CC1

Control unit

With built-in ambient temperature sensor.

To be installed in zone 1.

Load shedding

(if installed)

Outside air

temperature

Outdoor unit

Installation

water outlet

temperature

Installation

water return

temperature

Control by pilot wire for 2

zone (if any) with electric convectors.

Application: 1 FLOOR ZONE or 1 TERMINAL UNIT ZONE or 1

RADIATORS ZONE

ECO signal to remote controls.

For the terminal unit zone.

Application: 1 TERMINAL UNIT ZONE or 2 MIXED ZONES

BUS connection to 2-zone module ATK-WM2ZF or ATK-WM2ZM.

Applications: 2 FLOOR ZONES or 2 MIXED ZONES

Possible connections to be

made depending on the

applications

A) BUS

- 2-conductor shielded cable, minimum size 1 mm_ with shielding grounded on indoor unit side (*).

otal

length of the BUS connection: 40 meters (indoor unit / control box connection + indoor unit / 2-zone module

connection, if any).

- To be connected to the (+) and (-) terminals if terminal strip XB.

(*) Refer to the ground shielding principle in paragraph 4.3.3.

B) Outside temperature sensor

2-conductor cable, min. size 0.5 mm

Maximum length 25 meters.

o be connected to the heating board

A1.

- Note:

This sensor must be located outside in a location that is representative of the temperature to be measured (on a wall facing

North / North-west) and located away from parasitic heat sources (chimney

, thermal bridge, etc..) and sheltered from

inclement weather (under a roof overhand, for example)

C) Outdoor unit control connection

- 2-conductor shielded cable with shielding grounded on both the outdoor unit and indoor unit side.

- Minimum cable size: 0.75 mm

- Maximum length 70 meters.

- Connection as per paragraph 4.3.3.

Module additional heating load shedding signal (if installed)

wo possibilities:

1) By a "remote info" signal coming from the electrical utility meter: 1 twisted pair (6/10) cable with shielding (shielding

grounded on module side).

2) By a good quality

, potential-free external contact.

Contact closed = load shedding of the additional electric heating.

- 2-conductor cable, min. size 0.5mm

- Maximum length 25 meters.

- To be connected to the heating board

A1.

Indoor unit

E) Pilot wire for electric convectors (if any)

The pilot wire sends shut-down, "

anti-freeze" (long term absence) or "Economy" mode instructions to the electric

convectors in zone 2, and possibly in the case of 1 floor zone or 1 terminal unit zone applications.

Convector control (not supplied) must be adapted to receive this type of signal (standard GIF

AM 4).

Consult the manual of the electric convectors.

- 230 VAC signal from the heating board.

- 1.5 mm

single-pole cable adapted for the operating voltage.

Max. number of convectors controlled by the pilot wire: 20.

- To be connected to the heating board

A1.

- Note:

The electrical power supplied to the convectors must be the same as that of the module.

ECO signal for remote controls (if installed)

- In order to send reduced mode orders (Eco or standby) to the terminal unit remote control units in the case of

applications such as 1 terminal unit zone or 2 mixed zones.

- In the form of a potential-free contact which can used in VLV (Very Low Voltage), 2A max.

- To be connected to the heating board

A1.

- Note:

The contact can control up to 10 RCC10 (70250051) or RCC20 (70250052) type controls.

Consult the terminal unit and remote control documentation to connect this contact.

CONTROL PART CONNECTION DIAGRAM

- Route the control cables on the right side of the board.

- Pass the pilot wire (230 V) on the left side of the board.

CN1

230V

CN2 CN3 CN4

CN8 CN7 CN6 CN5

4321 4321 45 321 321

NUFP R1 R2 R3 C E1 E2 T+

A1 C A2 C4 321S1 C S2 C S3 A3 H2 H3

T- D1 D2 +-

234 1234 123 4

F D B

KM1 KM2 KM3 KM4

KA1 KA2

U1 U2

R1 R2 +

Pilot wire

Electric

convectors

(if any)

ECO signal

(if any)

Electrical

utility

meter

Load shedding

(if installed)

Control unit

BUS connection to

the 2-zone module,

ATK-WM2ZF or

ATK-WM2ZM

(if any).

Outside

temperature

sensor

Heating

board

Power terminal strip XA

Control terminal strip XB

To Outdoor

Unit

Keypad / RCS -

TM80 BG display

unit (if any)

4.3.5 - KEYPAD / RCS-TM80BG DISPLAY UNIT CONNECTION

• An RCS-TM80BG type keypad/display to be connected for

maintenance and troubleshooting operations.

Note:

This keypad/display unit must not be used for the installation's

normal operation.

4.3.6 - ROUTING OF CABLES

• To avoid problems related to electromagnetic disturbances, avoid routing control cables near power cables.

• Pass the cables through the cable glands.

• Route the control cables on the right side of the electric board.

•

Pass the pilot wire (230 V), if used, on the left side of the electric board.

U1 U2 R1 R2 +

Terminal XB

of the indoor unit

Black

White

BUS

Outside air temperature sensor

ECO signal for remote controls

Load shedding signal

Outdoor unit control connection

Pilot wire for electric convectors

Power supply

Bottom view of the indoor unit

5 - ACCESSORIES

5.1 - WATER CONNECTION HOSES

•

Length 1 m, insulated, female:

Ø 1” code

70600055 for SPW

-W366, 486

and 606.

6 - STARTING

Before carrying out any work on the installation, make sure that it is switched off and that access to it is prevented.

Any work must be carried out by personnel qualified and authorised to work on this type of machine.

IMPORTANT NOTE

Also refer to the installation instructions provided with the outdoor unit.

6.1 - PRELIMINARY CHECKS

6.1.1 - COOLING CIRCUIT

•

Refrigeration couplings correctly tightened.

• Both of the outdoor unit's shutoff valves are open.

• integrity of the cooling circuit (per Decree of 7 May 2007).

•

Also refer to the verifications indicated in the outdoor unit's installation instructions.

6.1.2 - HYDRAULIC CIRCUIT

• Hydraulic couplings correctly tightened.

• Hydraulic circuit operating correct:

- purge of circuits,

position of valves,

hydraulic pressure (2 bar),

• Integrity of the hydraulic circuit.

• Water quality:

In order for the heat pump to operate under good conditions and provide optimum performance, it is essential to

ensure that the system’s water circuit is clean. If the water circuit becomes clogged, this will significantly affect the

machine’

s performance. The circuit must therefore be cleaned with suitable products in compliance with current

standards as soon as it is installed, both for new and renovation work.

We recommend the use of products which are compatible with all metals and synthetic materials and approved by

official bodies.

Recommendations regarding water quality:

- PH: 6 to 9.

- TH: 10 to 20°F.

- Dry material in suspension: < 2 g/l

- Granulometry: < 0.4 mm

- Chloride: 50 mg/l maximum

- Conductivity: 50 to 500 µS/cm2

- Resistivity: 1 to 10 kΩ

- Fibre: no fibres.

Any disorder which may occur on our machines due to the poor quality of the fluid in the installation will not be

covered by the warranty.

6.1.3 - ELECTRICAL

SYSTEM

• The power cables are well fixed to their connection terminals. Terminals that are poorly tightened may cause overheating

and malfunctions.

• The electric cables are well insulated from any sections of sheet metal or metal parts which could damage them.

• The probe, control and power cables are properly separated.

• The machine is earthed.

6.1.4 - MISCELLANEOUS

• Overall good condition of the apparatus.

• No tools or other foreign objects inside the apparatus.

6.2 - CONFIGURATION AND PARAMETERISATION

6.2.1 - AUTO-ADDRESSING OF INDOOR AND OUTDOOR UNITS

• Set the control unit selector to “OFF”.

• Turn on the indoor and outdoor units. The unit cycles through an automatic addressing phase when the power is first

turned on. This phase may take 2 to 3 minutes and is indicated by the alternate blinking of

LED1 and LED2 on the

outdoor unit card.

When these indicator lights cease blinking, addressing is completed and communication between the indoor and outdoor

unit is established.

Note 1:

The addressing phase is indicated on the screen of the

RCS-TM80BG keyboard/display unit (if installed) by the flashing

“

SETTING” message.

Note 2:

Should a problem arise during this automatic addressing phase, a new phase can be restarted. To do this, simply

disconnect the power supply for at least 1 minute and when power is restored, press the black “

AUTO ADD” button on

the outdoor unit's electronic board.

Meaning of

LED1 and LED2 activity on the outdoor unit's board.

= ON steady

= ON blinking

= OFF

Meaning LED1 LED2

Auto-addressing in progress Alternating blinking

Power ON:

tep 1

no communication

tep 2

communication received from

the indoor unit

tep 3

normal communication

Alarm message Simultaneous blinking

No charge indicator

Refrigerant recovery mode

Alarms

(Refer to the details in the outdoor unit's

maintenance and troubleshooting

manual)

Repeated and alternating

blinking (of each indicator

light)

6.2.2 - MODULE CC1 CONFIGURATION

• The communication and control module manage the circulator and

the communication interface between the system and the generator

It is equipped with 2 micro-switches, No. 1 and No. 2.

Micro-switch No. 1:

In “ON” position, the circulator starts automatically if the outdoor

temperature is below 0°C to prevent the hydraulic circuit from

freezing. This position is recommended if the outdoor module is

installed in a location exposed to freezing temperatures (not

recommended).

The factory default setting for this micro-switch is “

OFF”.

Micro-switch No. 2:

Must be set to “ON” (activates the water flow safety on the

system).

6.2.3 - SYSTEM PARAMETERISATION

•

Make sure that the control unit selector is “

OFF”.

• Check the parameterisation and adapt it accordingly based on the

type of installation

The parameters are set on the control box (refer to the system's installation manual).

6.3 - ADDITIONAL HYDRAULIC CIRCUIT VERIFICATIONS

6.3.1 - FORCED CIRCULATOR OPERATION

• In order to conduct the final verifications of the hydraulic circuit, force

the pump to start as follows (installation power ON):

Set the system control unit to “

OFF”.

- Press and hold the button for 5 seconds.

The circulator starts.

The circulator indicator light flashes.

- Check that the “

O” flow indicator is illuminated.

6.3.2 - VERIFICATIONS

• Purging of circuits.

• Hydraulic pressure (2 bar).

• Water flowrate: the unit is equipped with 1/4 SAE pressure taps at the circulator inlet and outlet (see paragraph 2.1.1),

so that the pressure loss can be measured using a hydraulic pressure gauge. Use the circulator curves below to

determine the water flow rate.

In order for the apparatus to work properly, the nominal flow rate must be respected.

6.3.3 - CIRCULATOR CURVES

Micro-switches

No. 1 and No. 2

1 1.522.53

SPW-W366

1.72

SPW-W486

2.3

SPW-W606

2.7

SPW-W366

SPW

-W486

SPW-W606

ater flowrate (m

/h)

Manometric delivery head (kPa) of the circulator

Speed 1

Speed 2

Speed 3

7 - MAINTENANCE INSTRUCTIONS

7.1 - GENERAL MAINTENANCE

All equipment must be properly maintained in order to provide optimum performance over time. Faulty maintenance can result in

the cancellation of the product guaranty. Depending on the products, maintenance operations consist in the cleaning of filters (air,

water), internal and external exchangers, casings, and the cleaning and protection of condensate tanks. Treating odours and the

disinfection of room surfaces and volumes also contributes to the cleanliness of the air breathed by users.

•

Carry out the following operations at least once a year (the frequency depends on the installation and operating conditions):

- check for leaks on the refrigerating circuit (according to the order of 7th May 2007).

- check for traces of corrosion or oil stains around the refrigerating components,

- inspect the composition and the condition of the coolant and check that it does not contain traces of refrigerating fluid,

- cleaning the exchangers,

- checking the wear parts,

- checking the operating instructions and points,

- check the safety devices,

- de-dusting the electrical equipment cabinet,

- checking that the electrical connections are secure,

- checking the earth connection,

- check the hydraulic circuit (clean the filter, water quality, purge, flowrate, pressure, etc.).

7.2 - HEATER SAFETY

•

The unit's heater is equipped with an automatic-reset and a manual-reset safety thermostat.

• These thermostats trip in case of excessive temperature on the heater wall.

• Possible causes:

- Excessively low or inexistent water flowrate.

- Improperly purged water system.

• If the manual thermostat trips, correct the fault then reset the thermostat as follows:

Turn off and lock out the unit.

- Remove the cover.

- The thermostats are located against the heater partition, on the front (see paragraph 2.1.1).

- Press the button in the centre of the manual thermostat.

7.3 - PROTECTION OF HEATER CIRCUITS

• The heater features three heating elements each supplied with 230 V between phases and neutral. Each of these circuits

are protected by a modular circuit breaker (

Q1, Q2, Q3) located inside the electrical box.

7.4 - CONTROL CIRCUIT PROTECTION

•

The indoor unit's control circuit is protected by a modular circuit breaker

Q4 located next to module CC1. It is accessible

through the small window on the right-hand side of the unit (without removing the cover panel).

• Before doing any work on the installation, make sure it is switched off and all power supplies locked out.

• Also check that the capacitors are discharged.

• Any work must be carried out by personnel qualified and authorised to work on this type of machine.

• Prior to all maintenance and servicing on the refrigerating circuit, one must first shut down the unit then wait a

few minutes before installing temperature or pressure sensors. Certain equipment, such as the compressor and

piping, may reach temperatures above 100°C and high pressures may lead to serious burns.

IMPORTANT NOTE

6.3.4 - SHUTDOWN FORCED CIRCULATOR OPERATION

• Press and hold the button for 5 seconds.

The circulator stops.

The circulator indicator light and the “

O” flow rate light do out.

6.4 - OPERATION

• Installation power is ON.

• Start the system in the desired operating mode using the control box button (consult the system control manual and the

control box user's guide).

• If tripped:

Turn off and lock out the unit.

- Correct the fault.

Reset the circuit breaker.

Note:

The opening of circuit breaker Q4 disconnects only the control part. In the event of maintenance/servicing, all circuits must

be disconnected by opening the main circuit breaker

7.5 - TROUBLESHOOTING RECOMMENDATIONS

• All maintenance and servicing operations on the refrigerating circuit must be conducted in accordance with standard trade

practices and safety rules: recovery of the refrigerant, inert shielded (nitrogen) brazing, etc…

• All brazing operations must be conducted by qualified welders.

• For equipment charged with R 410 A, refer to the specific instructions in paragraph 4.1 and in the outdoor unit's manual.

• This unit is equipped with pressurised equipment, for example piping.

Use only genuine parts listed in the spare parts list for replacing defective refrigeration components.

• Pipes may only be replaced by copper tubing in compliance with standard NF EN 12735-1.

• Leak detection, in the case of pressure testing:

- Never use oxygen or dry air, as the risk of fire or explosion is present.

- Use dehydrated nitrogen or a nitrogen and refrigerant mix indicated on the manufacturer's plate.

- For units equipped with pressure gauges, the test pressure must not exceed the gauges' maximum allowable pressure

rating.

• All part replacement with other than genuine parts, all modifications of the refrigerating circuit, all replacement of refrigerant

by a fluid other than that indicated on the manufacturer's plate, all use of the unit outside the application limits defined in the

documentation, shall result in the cancellation of PED EC marking compliance which shall fall under the liability of the

individual who carried out these modifications.

• The technical information, relative to the safety requirements of the various applicable directives, is indicated on the

manufacturer's plate of the unit and mentioned on the 1

page of this manual.

8 - WIRING DIAGRAM

A1 Heating control PCB

A2 Indoor unit PCB

CC1 Communication and control module

E1 Water pressostat

F1 Automatic - heater safety thermostat

F2 Manual - heater safety thermostat

J1 Water flow switch

KA1 Heater fault relay

KA2 Water flow relay

KM1 R1 contactor

KM2 R2 contactor

KM3 R3 contactor

KM4 M1 contactor

M1 Water circulator pump

Q1 R1 circuit breaker

Q2 R2 circuit breaker

Q3 R3 circuit breaker

Q4 Control circuit breaker

R1 Support heating element

R2 Support heating element

R3 Support heating element

S1 Water inlet temperature sensor (system)

S2 Water outlet temperature sensor

S3 Outdoor air temperature sensor

S4 Heat pump exchanger temperature sensor (E2)

S5 Liquid line temperature sensor (E1)

S6 W

ater return temperature sensor (Heat pump) (TA)

TR Indoor unit board power supply transformer

Symbols of the components

BU Blue

BK Black

PK Pink

RD Red

WT White

Colours of the wires

RD +

WH -

WH-R2

BK-R1

RD +

WH -

BU - 4

BU - 5

BU - 6

21-+

N U

CN80/PNL

TC/E2

CN041/RJ

AC IN / CN067

CN040

TRANS-P

TRANS - S

CN076

T20

TCJ/E1

CN30/FS

BU-1

KM1

CN8 CN7 CN6 CN5

CN1 CN2 CN3 CN4

4321 4 13 212345321

23 1234 1234 2134

1CCS2 S3 24 31A1 CCA2

FP R1 R2 R3 C +D1D2 -

3 H1 H2 H3

E1 E2 T+ T-

230V

KM2

KM3

KA1

KM3

Q3Q2Q1

KM2

X4 CX3

BUS

KA2

KA1

1214

KA2

1214

KM4

PK-U1

IU PCB

CC1

230V

POMPE

SYS

COM

H2O

KA2

2224

KM1

BU-U2

ELECTRICAL DIAGRAM - SPW-W366HH / 486HH / 606HH - 230/1/50 - 400/3N/50

10 05 845 - 00

Power supply 400/3N/50Hz

System

Outdoor

unit

230/1/50Hz

Pilot

Eco

Inlet

Téléinfo

Load

shedding

IMPORTANT!

Veuillez lire ce qui suit avant de commencer

Ce système de conditionnement de l'air répond à des normes

strictes de fonctionnement et de sécurité. En tant qu'installateur

ou ingénieur de maintenance, une partie importante de votre

travail est d'installer ou d'entretenir le système de manière à ce

qu'il fonctionne efficacement en toute sécurité.

Pour effectuer une installation sûre et obtenir un

fonctionnement sans problème, il vous faut:

• Lire attentivement cette brochure d'information avant de

commencer.

• Procéder à chaque étape de l'installation ou de la réparation

exactement comme il est indiqué.

• Respecter toutes les réglementations électriques locales,

régionales et nationales.

• Observer toutes les recommandations de prudence et de

sécurité données dans cette notice.

• Pour l'alimentation de l'appareil utiliser une ligne électrique

dédiée.

Ce symbole fait référence à une pratique dangereuse ou

imprudente qui peut entraîner des blessures personnelles ou la

mort.

Ce symbole fait référence à une pratique dangereuse ou

imprudente qui peut entraîner des blessures personnelles ou

des dégâts matériels, soit à l'appareil, soit aux installations.

Si nécessaire, demandez que l'on vous prête assistance

Ces instructions suffisent à la plupart des sites d'installation et

des conditions de maintenance. Si vous avez besoin

d'assistance pour résoudre un problème particulier, adressez-

vous à notre service après vente ou à votre revendeur agréé

pour obtenir des instructions supplémentaires.

Dans le cas d'une installation incorrecte

Le fabricant ne sera en aucun cas responsable dans le cas

d'une installation ou d'une maintenance incorrecte, y compris

dans le cas de non-respect des instructions contenues dans ce

document

PRÉCAUTIONS PARTICULIERS

• Pour l’installation: raccorder les liaisons frigorifiques, puis les

liaisons électriques.

Pour le démontage: procéder de manière inverse.

Lors du câblage

UNE DECHARGE ELECTRIQUE PEUT ENTRAINER

UNE BLESSURE PERSONNELLE GRAVE OU LA MORT.

SEUL UN ELECTRICIEN QUALIFIE ET EXPERIMENTE

DOIT EFFECTUER LE CABLAGE DE CE SYSTEME.

• Ne mettez pas l'appareil sous tension tant que tout le système

de câbles et de tuyaux n'est pas terminé ou rebranché et

vérifié, pour assurer la mise à la terre.

•

Des tension électriques extrêmement dangereuses sont

utilisées dans ce système. Veuillez consulter attentivement le

schéma de câblage et ses instructions lors du câblage.

Des connexions incorrectes ou une mise à la terre inadéquate

peuvent entraîner des blessures accidentelles ou la mort.

• Effectuez la mise à la terre de l'appareil en respectant les

réglementations électriques locales.

• Le câble jaune/vert ne peut en aucun cas être utilisé pour

toute autre connexion que celle de la mise à la terre.

•

Serrez fermement toutes les connexions. Un câble mal fixé

peut entraîner une surchauf

fe au point de connexion et

présenter un danger potentiel d'incendie.

• Il ne faut en aucun cas laisser les câbles toucher la tuyauterie

du réfrigérant, le compresseur ou toute pièce mobile.

• N’utilisez pas de câble multiconducteur pour le câblage des

lignes d’alimentation électrique et celles de commande.

Utilisez des câbles séparés pour chaque type de ligne.

Lors du transport

Soyez prudent lorsque vous soulevez et déplacez les appareils

intérieur et extérieur. Demandez à un collègue de vous aider, et

pliez les genoux lors du levage afin de réduire les efforts sur votre

dos. Les bords acérés ou les ailettes en aluminium mince se

trouvant sur le climatiseur risquent de vous entailler les doigts.

Lors de l'installation...

... dans une pièce

Isolez correctement tout tuyau circulant à l'intérieur d'une pièce

pour éviter que de la condensation ne s'y dépose et ne goutte,

ce qui pourrait endommager les murs et les planchers.

...dans des endroits humides ou sur des surfaces irrégulières

Utilisez une plate-forme surélevée pour offrir une base solide et

régulière à l'appareil extérieur.

Ceci permettra d'éviter des dégâts causés par l'eau et des

vibrations anormales.

... dans une zone exposée à des vents forts

Ancrez solidement l'appareil extérieur avec des boulons et un

châssis en métal. Réalisez un déflecteur efficace.

...dans une zone neigeuse (pour le système du type réversible)

Installez l'appareil extérieur sur une plate-forme surélevée à un

niveau supérieur à l'amoncellement de la neige. Réalisez des

évents à neige.

Lors de la connexion des tuyaux de réfrigération

• Limitez au maximum la longueur des tuyaux.

• Les raccordements sont de type flare.

• Appliquez de l’huile frigorifique sur les surfaces de contact

avant de les connecter, puis serrez l'écrou avec une clé

dynamométrique pour effectuer une connexion sans fuite.

• Recherchez soigneusement la présence de fuites avant

d'effectuer l'essai de fonctionnement.

NOTE:

Selon le type du système, les tuyaux de gaz et de liquide

peuvent être petits ou gros. Par conséquent, afin d'éviter toute

confusion, le tuyau de réfrigérant de votre modèle particulier est

dénommé "petit" pour le liquide et "gros" pour le gaz.

Lors de la maintenance

• Interrompre l'alimentation électrique sur le commutateur

principal avant d'ouvrir l'appareil pour vérifier ou réparer le

câblage et les pièces électriques.

• Veillez à maintenir vos doigts et vos vêtements éloignés de

toutes les pièces mobiles.

• Nettoyez le site lorsque vous avez fini, en pensant à vérifier

que vous n'avez laissé aucune ébarbure de métal ou morceau

de câble à l'intérieur de l'appareil dont vous avez effectué la

maintenance.

• Aérez la pièce pendant l'installation et l'essai du circuit

réfrigérant; assurez-vous que, après l'installation, des fuites

de gaz réfrigérant ne se produisent pas, puisque le contact

avec des flammes ou des sources de chaleur peut être

toxique et très dangereux.

DANGER

PRUDENCE

DANGER

REMARQUE : Ce symbole et ce système de recyclage s'appliquent uniquement aux pays de l’UE. Ils ne s'appliquent pas aux

pays des autres régions du monde.

Votre produit est conçu et fabriqué avec des matériels et des composants de qualité supérieure qui peuvent être recyclés et réutilisés.

Ce symbole signifie que les équipements électriques et électroniques en fin de vie doivent être éliminés séparément des ordures

ménagères.

Nous vous prions donc de confier cet équipement à votre centre local de collecte/recyclage.

Dans l’Union Européenne, il existe des systèmes sélectifs de collecte pour les produits électriques et électroniques usagés.

Aidez-nous à conserver l’environnement dans lequel nous vivons !

La page charge ...

Sanyo SPW-W366HH58 Installation Instructions Manual

Marque: Sanyo

Modèle: SPW-W366HH58

Catégorie: Climatiseurs split-system

Taper: Installation Instructions Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Sanyo SPW-W366HH58

Sanyo SPW-W366HH58 Installation Instructions Manual

Ce manuel convient également à

Sanyo SPW-W366HH58 Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents