ROSIERES RDYGE1060CMC/E Manuel utilisateur

USER MANUAL

RANGE COOKER

100 cm

Gas & Electrical

À gaz et électrique

GB

FR

H10-20-180-493 Rev 003

MANUEL D'UTILISATION

2

Dear User,

Our objective is to make this product provide you with the best output

which is manufactured in our modern facilities in a careful working

environment, in compliance with total quality concept.

Therefore, we suggest you to read the user manual carefully before

using the product and, keep it permanently at your disposal.

Note: This user manual is prepared for more than one model. Some of

the features specified in the Manual may not be available in your

appliance.

All our appliances are only for domestic use, not for commercial use.

Products marked with (*) are optional.

“THIS APPLIANCE SHALL BE INSTALLED IN ACCORDANCE WITH THE

REGULA TIONS FORCE AND ONLY USED IN A WELL VENTILATED SPACE. READ

THE INSTRUCTIONS BEFORE INSTALLING OR USING THIS APPLIANCE”

“Conforms with the WEEE Regulations."

GB

3

Contents

Important warnings 4

Electrical connection 16

Gas connection 17

Introduction of the appliance 22

Accessories 23

Technical features of your oven 24

Installation of your oven 27

Chain lashing illustration 29

Using oven section 29

Using the grill 30

Using the chicken roasting 30

Using cooker section 31

Description of oven 34

Cooking time table 35

Maintenance and cleaning 36

Installation of the oven door 37

Cleaning and maintenance of the

Oven’s front door glass 38

Catalytic walls 39

Rack positions 39

Changing the oven lamp 40

Using the grill deector sheet 41

Troubleshooting 42

Handling rules 44

Recommendations for energy saving 44

Environmentally-friendly disposal 45

Package information 45

4

IMPORTANT WARNINGS

1. Installation and repair should always be performed

by “AUTHORIZED SERVICE”. Manufacturer shall not be

held responsible for operations performed by unauthorized

persons.

2. Please read this operating instructions carefully.

Only by this way you can use the appliance safely and

in a correct manner.

3. The oven should be used according to operating

instructions.

4. Keep children below the age of 8 and pets away

when operating.

5. WARNING: The accessible parts may be hot while using

the grill. Keep away from children.

6. WARNING: Fire hazard; do not store the materials on

the cooking surface.

7. WARNING: The appliance and its accessible parts are

hot during operation.

8. Setting conditions of this device are specied on

the label. (Or on the data plate)

9. The accessible parts may be hot when the grill is

used. Small children should be kept away.

10. WARNING: This appliance is intended for cooking. It

should not be used for other purposes like heating a room.

11. To clean the appliance, do not use steam cleaners.

12. Ensure that the oven door is completely closed

after putting food inside the oven.

GB

5

13. NEVER try to put out the re with water. Only shut

down the device circuit and then cover the ame with

a cover or a re blanket.

14. Children under 8 years of age should be kept away,

if they cannot be monitored continuously.

15. Touching the heating elements should be avoided.

16. CAUTION: Cooking process shall be supervised.

Cooking process shall always be supervised.

17. This device can be used by children over 8 years

of age, people with physical, hearing or mental chal-

lenges or people with lack of experience or knowledge;

as long as control is ensured or information is provided

regarding the dangers.

18. This device has been designed for household use

only.

19. Children must not play with the appliance. Cleaning

or user maintenance of the appliance shall not be

performed by children unless they are older than 8

years and supervised by adults.

20. Keep the appliance and its power cord away from

children less than 8 years old.

21. Put curtains, tulles, paper or any ammable (ignitable)

material away from the appliance before starting to use

the appliance. Do not put ignitable or ammable materials

on or in the appliance.

22. Keep the ventilation channels open.

6

23. The appliance is not suitable for use with an external

timer or a separate remote control system.

24. Do not heat closed cans and glass jars. The pressure

may lead jars to explode.

25. Oven handle is not a towel drier. Do not hang towels,

etc. on the oven handle.

26. Do not place the oven trays, plates or aluminium

foils directly on the oven base. The accumulated heat

may damage the base of the oven.

27. While placing food to or removing food from the

oven, etc., always use heat resistant oven gloves.

28. Do not use the product in states like medicated

and/or under inuence of alcohol which may affect your

ability of judgement.

29. Be careful when using alcohol in your foods. Alcohol

will evaporate at high temperatures and may catch re to

cause a re if it comes in contact with hot surfaces.

30. After each use, check if the unit is turned off.

31. If the appliance is faulty or has a visible damage,

do not operate the appliance.

32. Do not touch the plug with wet hands. Do not pull

the cord to plug off, always hold the plug.

33. Do not use the appliance with its front door glass

removed or broken.

34. Place the baking paper together with the food into

a pre-heated oven by putting it inside a cooker or on an

oven accessory (tray, wire grill etc.).

GB

7

35. Do not put objects that children may reach on the

appliance.

36. It is important to place the wire grill and tray properly

on the wire racks and/or correctly place the tray on the

rack. Place the grill or tray between two rails and make

sure it is balanced before putting food on it.

37. Against the risk of touching the oven heater elements,

remove excess parts of the baking paper that hang over

from the accessory or container.

38. Never use it at higher oven temperatures than the

maximum usage temperature indicated on your baking

paper. Do not place the baking paper on the base of the

oven.

39. When the door is open, do not place any heavy

object on the door or allow children to sit on it. You

may cause the oven to overturn or the door hinges to be

damaged.

40. The packaging materials are dangerous for children.

Keep packaging materials away from the reach of children.

41. Do not use abrasive cleaners or sharp metal scrapers

to clean the glass as the scratches that may occur on

the surface of the door glass may cause the glass to

break.

42. Do not place the appliance on a surface covered

with carpets. Electric parts gets overheated since there

will be no ventilation from below. This will cause failure

of the appliance.

8

43. Do not hit glass surfaces of vitro-ceramic cookers

with a hard metal, resistance can get damaged. It may

cause an electric shock.

44. User should not handle the oven by himself.

45. Use shall be careful when cleaning gas burners.

It may cause personal injuries.

46. Food can spill when foot of oven is dismantled or

gets broken, be careful. It may cause personal injuries.

47. During usage, the internal and external surfaces

of the oven get hot. As you open the oven door, step

back to avoid the hot vapour coming out from the interior.

There is risk of burning.

48. Upper cover of the oven can be closed for a reason,

than cookware can trip over. Step back to avoid the hot

food coming on you. There is risk of burning.

49. Do not place heavy objects when oven door is

open, risk of toppling.

50. User should not dislocate the resistance during

cleaning. It may cause an electric shock.

51. Do not remove ignition switches from the appliance.

Otherwise, live electric cables can be accessed. It may

cause an electric shock.

52. Oven supply can be disconnected during any

construction work at home. After completing the work,

re-connecting the oven shall be done by authorized service.

53. Do not place metal utensils such as knife, fork, spoon

on the surface of the appliance, since they will get hot.

GB

9

54. To prevent overheating, the appliance should not

be installed behind of a decorative cover.

55. Turn off the appliance before removing the

safeguards. After cleaning, install the safeguards

according to instructions.

56. Cable xing point shall be protected.

57. WARNING: Don’t use oven and grill burners in same

time.

58. Please don’t cook the food directly on the tray /

grid. Please put the food into or on appropriate tools

before putting them in the oven.

59. Hot surface, leave for cooling before closing the

cover.

10

Electrical Safety

1. Plug the appliance in a grounded socket protected by

a fuse conforming to the values specied in the technical

specications chart.

2. Have an authorized electrician set grounding equipment.

Our company shall not be responsible for the damages

that shall be incurred due to using the product without

grounding according to local regulations.

3. The circuit breaker switches of the oven shall be

placed so that end user can reach them when the oven

is installed.

4. The power supply cord (the cord with plug) shall

not contact the hot parts of the appliance.

5. If the power supply cord (the cord with plug) is

damaged, this cord shall be replaced by the manufacturer

or its service agent or an equally qualied personnel to

prevent a hazardous situation.

6. Never wash the product by spraying or pouring water

on it! There is a risk of electrocution.

7. WARNING: To avoid electric shock, ensure that the

device circuit is open before changing the lamp.

8. WARNING: Cut off all supply circuit connections before

accessing the terminals.

9. WARNING: If the surface is cracked, turn off the appliance

to avoid risk of electric shock.

10. Do not use cut or damaged cords or extension

cords other than the original cord.

GB

11

11. Make sure that there is no liquid or humidity in

the outlet where the product plug is installed.

12. The rear surface of the oven also heats up when

the oven is operated. Electrical connections shall not

touch the rear surface, otherwise the connections may

be damaged.

13. Do not tighten the connecting cables to the oven

door and do not run them over hot surfaces. If the cord

melts, this may cause the oven to short circuit and

even a re.

14. Unplug the unit during installation, maintenance,

cleaning and repair.

15. If the power supply cable is damaged, it must be

replaced by its manufacturer or authorized technical

service or any other personnel qualied at the same

level, in order to avoid any dangerous situation.

16. Make sure the plug is inserted rmly into wall

socket to avoid sparks.

17. Do not use steam cleaners for cleaning the appliance,

otherwise electric shock may occur.

18. An omnipolar switch capable to disconnect

power supply is required for installation. Disconnection

from power supply shall be provided with a switch or

an integrated fuse installed on xed power supply

according to building code.

19. Appliance is equipped with a type ‘’Y’’ cord cable.

12

20. Fixed connections shall be connected to a power

supply enabling omnipolar disconnection. For appliances

with over voltage category below III, disconnection device

shall be connected to xed power supply according to

wiring code.

Gas Safety

1. This appliance is not connected to burning prod-

ucts evacuation apparatus. This appliance must be

connected and installed according to the installation

regulations in force. Conditions regarding ventilation

must be considered.

2. When a gas cooking appliance is used; humidity,

heat and burning products are generated in the room.

First of all, make sure the kitchen is well ventilated

when operating the appliance and maintain natural

ventilation openings or install a mechanical ventilation

equipment.

3. After using the appliance heavily for en extended

period of time, additional ventilation may be required.

For example open a window or adjust a higher speed for

mechanical ventilation, if any.

4. This appliance must be used only in well ventilated

locations in accordance with the regulations in force.

Please read the manual before installing or using this

product.

5. Before positioning the appliance, make sure local

network conditions (gas type and gas pressure) meets

appliance requirements.

GB

13

6. The mechanism cannot be run for longer than 15

seconds. If the burner is not on after 15 seconds, stop

the mechanism and wait for at least one minute before

trying to ignite the burner again.

7. All kinds of operations to be performed on gas

installation must be performed by authorized and

competent people.

8. This appliance is adjusted for natural gas (NG). If

you have to use your product with a different gas type,

you have to apply to authorized service for the conversion.

9. For proper operation, hood, gas pipe and clamp

should be replaced periodically accordint to manufacturer

recommendations and when required.

10. Gas should burn well in gas products. Well

burning gas can be understood from blue ame and

continuous burning. If gas does not burn sufciently,

carbon monoxide (CO) can be generated. Carbon monoxide

is a colourless, odourless and very toxic gas; even small

amounts have lethal effect.

11. Ask your local gas supplies about the phone numbers

for emergencies related to gas and the measures to be

taken upon gas odour is detected.

14

What To Do When Gas Odour Is Detected

1. Do not use naked ame, and do not smoke.

2. Do not operate any electrical switch. (For example:

lamp switch or doorbell)

3. Do not use telephone or mobile phone.

4. Open the doors and windows.

5. Close all valves on the appliances that utilize gas

and the gas counters.

6. Call re brigade from a telephone outside the home.

7. Check all hoses and their connections against leaks.

If you still smell gas, leave the house and warn your

neighbours.

8. Do not enter into the house until authorities clarify

it is safe.

GB

15

Intended Use

1. This product is designed for home use. Commercial

use of the appliance is not permitted.

2. This appliance may only be used for cooking

purposes. It shall not be used for other purposes like

heating a room.

3. This appliance shall not be used to heat plates under

the grill, drying clothes or towels by hanging them on

the handle or for heating purposes.

4. The manufacturer assumes no responsibility for any

damage due to misuse or mishandling.

5. Oven part of the unit may be used for thawing,

roasting, frying and grilling food.

6. Operational life of the product you have purchased

is 10 years. This is the period for which the spare parts

required for the operation of this product as dened is

provided by the manufacturer.

16

Electrical Connection

1. Your oven requires 16 or 32 Ampere fuse according to the appliance’s

power. If necessary, installation by a qualied electrician is recommended.

2. Your oven is adjusted in compliance with 220-240V AC/380-415V

AC 50/60Hz.electric supply. If the mains are different from this specied

value, contact your authorized service.

3. Electrical connection of the oven should only be made by the sockets

with earth system installed in compliance with the regulations. If there

is no proper socket with earth system in the place where the oven will be

placed, immediately contact a qualed electrician. Manufacturer shall

never be responsible from the damages that will arise because of the

sockets connected to the appliance with no earth system. If the ends of

the electrical connection cable are open, according to the appliance type,

make a proper switch installed in the mains by which all ends can be

disconnected in case of connecting / disconnecting from / to the mains.

4. If your electric supply cable gets defective, it should denitely be

replaced by the authorized service or qualed electricians in order to

avoid from the dangers.

5. Electrical cable should not touch the hot parts of the appliance.

6. Please operate your oven in dry atmosphere.

Electrical connection scheme

220-240V~50/60 Hz

H05 VV-F 3G 4mm²

Live

Phase

Neural

Earth

GB

17

Gas Connection

WARNING: Before starting any work related with gas installation, turn off

gas supply. Risk of explosion.

1. Before your appliance is connected to the gas supply, ensure that

the gas category and pressure specications shown in the data plate

corresponds with your gas supply. If necessary call authorized service for

adjusting to gas category.

2. This appliance shall be installed in accordance with the regulations

in force and only used in a well ventilated space. Read the instructions

before installing or using this appliance. In the interest of safety this

appliances must be installed and / or serviced by a competent person as

stated in the gas safety regulations current editions.

3. The appliance must not be installed in a room without a window or

other controllable opening. If is installed in a room without a door which

opens directly to the outside, a permanent opening is required. The air

circulation should be 2 m³/h per kW of burners.

4. The gas connection should be performed from the right or left. For

this reason, change the hose nozzle, plug and the seals.

5. Please use exible hose for gas connection.

6. If you make a connection with a exible metal hose, locate a seal

between the main gas pipes.

7. The inner diameter of the exible hose, which the butane hose nozzle

is connected, should be 6 mm for the house-type gas tubes. The inner

diameter of the exible hose, which the natural hose nozzle is connected,

should be 15 mm.The hose should tightly be tted to the hose nozzle

by squeezing with a clamp. The hose should be replaced before its last

expiry date.

8. CAUTION: Make the oven connection to the gas inlet valve, the hose

length must be short and be sure that there is no leakage. The exible

hose used should not be longer than 125 cm for safety.

9. Re-inspect the gas connection.

10. When placing your oven to its location, ensure that it is at the counter

level. Bring it to the counter level by adjusting the feet if necessary.

18

WARNING: Do not make gas hose and electrical cable of your oven go

through the heated areas, especially through the rear side of the oven. Do

not move gas connected oven. Since the forcing shall loosen the hose,

gas leakage may occur.

For LPG connection;

For LPG (cylinder) connection, afx metal

clamp on the hose coming from LPG

cylinder. Afx an edge of the hose on hose

inlet connector behind the appliance by

pushing to end through heating the hose

in boiled water. Afterward, bring the clamp

towards end section of the hose and tighten

it with screwdriver. The gasket and hose inlet

connector required for connection is as the

picture shown below.

NOTE: The regulator to be afxed on LPG cylinder should have 300

mmSS feature.

For natural gas connection;

WARNING: Natural gas connection should

be done by authorized service.

For natural gas connection, place gasket

in the nut at the edge of natural gas connection

hose. To install the hose on main gas pipe,

turn the nut. Complete the connection by

making gas leakage control.

Main Gas Pipe

Gasket

Hose Inlet Connector

Metal Clamp

Lpg Connection Hose

Main Gas Pipe

Gasket

Nut

Natural Gas

Connection Hose

GB

19

Gas hose passage way

Connect the appliance to the gas piping tap

in shortest possible route and in a way

that ensure no gas leakage will occur.

In order to carry on a tightness and sealing

safety check ensure that the knobs on

the control panel are closed and the gas

cylindir is open.

WARNING: While performing a gas leak-

age check, never use any kind of lighter,

match, cigarette or similar burning

substance.

Apply soap bubble on the connection

points. If there is any kind of leakage

then it will cause bubbling.

While inserting the appliance in place

ensure that it is on the same level with

the worktop. If required adjust the legs

inorder the make level with the worktop.

Use the appliance on a level surface and

in a well ventilated environment.

WARNING: Before placint the appliance, check that the local distribution

conditions (gas type and pressure) conform to the product settings.

Reduced ame gas cock adjustment

1. Please use driver with special head for removed and install nozzle as

(gure 3).

2. Please remove nozzle (gure 4) from burner with special nozzle driver

and install new nozzle. (gure 5)

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

20

Ventilation of room

The air needed for burning is received from room air and the gases emitted

are given directly in room. For safe operation of your product, good room

ventilation is a precondition. If no window or room to be utilized for room

ventilation is available, additional ventilation should be installed. However,

room has a door opening outside, it is no needed to vent holes.

Room size Ventilating opening

Smaller than 5 m³ min. 100 cm²

Between 5 m³ - 10 m³ min. 50 cm²

Bigger than 10 m³ no need

In basement or cellar min. 65 cm²

Reduced gas ow rate setting for hob taps

1. Ignite the burner that is to be adjustment and turn the knob to the

reduced position.

2. Remove the knob from the gas tap.

3. Use an appropriately sized screwdriver to adjust the ow rate adjustment

screw. For LPG (butane-pro pane) turn the screw clockwise. For the

naturel gas, you should turn the screw counter- clockwise once.

“The normal length of a straight ame in the reduced position should

be 6-7 mm.“

4. If the ame is higher then the desired position, turn the screw clockwise.

If it is smaller turn anticolockwise.

5. For the last control, bring the burner both to higt-ame and reduced

positions and check whether the ame is on or off.

Depending on the type of gas tap used in your appliance the adjustment

screw position may vary.

GB

La page charge ...

ROSIERES RDYGE1060CMC/E Manuel utilisateur

Ce manuel convient également à

ROSIERES RDYGE1060CMC/E Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents