Magnavox 19MF339B Le manuel du propriétaire

User Manual

Manuel de l’utilisateur

Guía del usuario

22MF339B

19MF339B

LCD TV

Quick Use Guide Inside!

Guide d’usage Rapide Incluse!

Guía de Uso Rápido Incluida!

English

Français

Español

1-866-341-3738

MODEL NUMBER SERIAL NUMBER

HIGH-DEFINITION TELEVISION

2

EN

Know these safety symbols

This “bolt of lightning” indicates

uninsulated material within your unit

may cause an electrical shock. For the safety

of everyone in your household, please do not

remove product covering.

The “exclamation point” calls attention to

features for which you should read the en-

closed literature closely to prevent operating

and maintenance problems.

WARNING : To reduce the risk of re or

electric shock, this apparatus should not be

exposed to rain or moisture and objects lled

with liquids, such as vases, should not be

placed on this apparatus.

CAUTION : To prevent electric shock, match

wide blade of plug to wide slot, fully insert.

ATTENTION : Pour éviter les choc électriques,

introduire la lame la plus large de la che dans

la borne correspondante de la prise et pousser

jusqu’au fond.

For Customer Use

Enter below the Serial No. which is located

on the rear of the cabinet. Retain this

information for future reference.

Model No._____________________________

Serial No. _____________________________

Registering your model with MAGNAVOX makes you eligible for all of the valuable benets listed below, so don’t miss out.

Complete and return your Product Registration Card at once, or register online at www.magnavox.com/support to ensure:

*Proof of Purchase

Returning the enclosed card

guarantees that your date of

purchase will be on le, so no

additional paperwork will be

required from you to obtain

warranty service.

*Product Safety

Notication

By registering your product, you’ll

receive notication directly from

the manufacturer - in the rare

case of a product recall or safety

defect.

*Additional Benets

Registering your product

guarantees that you’ll receive all

of the privileges to which you’re

entitled, including special

money-saving oers.

Congratulations on your purchase,

and welcome to the “family!”

Dear MAGNAVOX product owner:

Thank you for your condence in

MAGNAVOX. You’ve selected one of the

best-built, best-backed products available today.

We’ll do everything in our power to keep you happy

with your purchase for many years to come.

As a member of the MAGNAVOX “family,” you’re

entitled to protection by one of the most

comprehensive warranties and outstanding service

networks in the industry. What’s more, your

purchase guarantees you’ll receive all the

information and special oers for which you qualify,

plus easy access to accessories from our convenient

home shopping network.

Most importantly, you can count on our

uncompromising commitment to your total

satisfaction.

All of this is our way of saying welcome - and

thanks for investing in a MAGNAVOX product.

P.S. To get the most from your MAGNAVOX

purchase, be sure to complete and return your

Product Registration Card at once or register

online at:

www.magnavox.com/support

Visit our World Wide Web Site at www.magnavox.com/support

Return your Product Registration Card or register online at

www.magnavox.com/support today to get the very most from your purchase.

3

EN

Read before operating equipment

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any of the ventilation openings.

Install in accordance with the manufacturers instructions.

Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers)

that produce heat.

Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and third grounding prong. The wide blade or third

prong are provided for your safety. When the provided

plug does not t into your outlet, consult an electrician for

replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

Only use attachments/accessories specied by the

manufacturer.

Use only with a cart, stand, tripod, bracket, or table

specied by the manufacturer, or sold with the appara-

tus. When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when un-

used for long periods of time.

Refer all servicing to qualied service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into apparatus, the appara-

tus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

Damage Requiring Service - The appliance should be

serviced by qualied service personnel when:

A. The power supply cord or the plug has been damaged;

B. Objects have fallen, or liquid has been spilled into the

appliance;

C. The appliance has been exposed to rain

D. The appliance does not appear to operate normally or

exhibits a marked change in performance;

E. The appliance has been dropped, or the enclosure dam-

aged.

Tilt/Stability - All televisions must comply with

recommended international global safety standards for tilt

and stability properties of its cabinet design.

• Do not compromise these design standards by applying

excessive pull force to the front, or top, of the cabinet

which could ultimately overturn the product.

• Also, do not endanger yourself, or children, by placing

electronic equipment/toys on the top of the cabinet. Such

items could unsuspectingly fall from the top of the set and

cause product damage and/or personal injury.

Wall or Ceiling Mounting - The appliance should be

mounted to a wall or ceiling only as recommended by the

manufacturer.

Power Lines - An outdoor antenna should be located away

from power lines.

Outdoor Antenna Grounding - If an outside antenna is

connected to the receiver, be sure the antenna system is

grounded so as to provide some protection against voltage

surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA

No. 70-1984, provides information with respect to proper

grounding of the mast and supporting structure, ground-

ing of the lead-in wire to an antenna discharge unit, size of

grounding connectors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode. See Figure below.

Object and Liquid Entry - Care should be taken so that

objects do not fall and liquids are not spilled into the enclo-

sure through openings.

Battery Usage CAUTION - To prevent battery leakage

that may result in bodily injury, property damage, or

damage to the unit:

• Install all batteries correctly, with + and - aligned as

marked on the unit.

• Do not mix batteries (old and new or carbon and

alkaline, etc.).

• Remove batteries when the unit is not used for a long

time.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12

13.

14.

15.

Note to the CATV system installer : This reminder is provided to call the CATV system installer’s attention to Article

820-40 of the NEC that provides guidelines for proper grounding and, in particular, species that the cable ground shall

be connected to the grounding system of the building, as close to the point of cable entry as practical.

Example of Antenna Grounding as

per NEC - National Electric Code

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

16.

17.

18.

19.

20.

21.

IMPORTANT SAFETY INSTRUCTIONS

4

EN

I

NTRODUCTION

 Precaution  Precaution

This Class B digital apparatus complies with Canadian ICES-003.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

WARNING: Batteries (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnect the mains plug to shut off when find trouble or not in use. The mains plug shall remain readily operable.

This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided.

Make sure to leave a space of 2.8 inches (7cm) or more around this apparatus.

TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE

• Do not handle the AC power cord with wet hands.

• Do not remove this unit’s cabinet. Touching parts inside the cabinet could result in electric shock and/or damage to this

unit. For service and adjustment inside the cabinet, call a qualified dealer or an authorized service center.

• Do not pull on the AC power cord when disconnecting it from an AC outlet. Grasp it by the plug.

• Do not put your fingers or objects into the unit.

LOCATION AND HANDLING

• The openings should not be blocked by placing the unit on a bed, sofa, carpet, rug, or other similar surface.

• Do not install the unit near or over a radiator or heat register.

• Do not install the unit in direct sunlight, near strong magnetic fields, or in a place subject to dust or strong vibration.

• Avoid a place with drastic temperature changes.

• Install the unit in a horizontal and stable position. Do not place anything directly on top or bottom of the unit.

Depending on your external devices, noise or disturbance of the picture and/or sound may be generated if the unit is

placed too close to them. In this case, please ensure enough space between the external devices and the unit.

• Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.

NOTE ABOUT RECYCLING

• This unit’s packaging materials are recyclable and can be reused.

Please dispose of any materials in accordance with your local recycling regulations.

• Batteries should never be thrown away or incinerated but disposed of in accordance with your local

regulations concerning chemical wastes.

 Trademark Information

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

• Products that have earned ENERGY STAR® are designed to protect the environment through superior energy efficiency.

WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the instructions.

Like all LCD products, this set contains a lamp with Mercury, please dispose of according

to all Local, State and Federal laws. For the disposal or recycling information, contact:

www.mygreenelectronics.com or www.eiae.org

Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing

on it. A falling unit can cause serious injury or even death.

FCC WARNING

This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause harmful

interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this

apparatus if an unauthorized change or modification is made.

RADIO-TV INTERFERENCE

This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This apparatus generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this apparatus does cause harmful interference to radio or television reception, which

can be determined by turning the apparatus off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the apparatus and receiver.

3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

DECLARATION OF CONFORMITY

Trade Name: MAGNAVOX Responsible Party: FUNAI CORPORATION, INC.

Model: 22MF339B / 19MF339B Address: 201 Route 17 North Suite No. 903 Rutherford, New Jersey 07070 U.S.A.

Telephone Number: 201-727-4560

5

EN

INTRODUCTION PREPARATION

WATCHING TV

OPTIONAL SETTING TROUBLESHOOTING

INFORMATION

 Supplied Accessories

AAA

• If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free

customer support line found on the cover of this manual.

user manual

(1EMN24239A)

quick start guide

(1EMN24541)

remote control

(NF802UD)

batteries

(AAA x 2)

screw kit for attaching

the stand

(1ESA19876)

o the part No. with

ua

l

e

co

n

t

r

ol

l

2

UD

)

batte

b

(

AA

A

 Attaching the Stand

You must attach the stand to the unit to have it as a table top unit. Be sure the front and rear of the stand match the

proper direction.

Note:

• When attaching the stand, ensure that all screws are tightly fastened. If the stand is not properly attached, it could cause the unit to fall,

resulting in injuries as well as damage to the unit.

• Make sure to use a table which can support the weight of this unit and is larger than this unit.

• Make sure the table is in a stable location.

1

Spread a thick and soft cloth over a

table as shown below.

Place the main unit face down onto it.

2

Align the 2 stand hooks with the two

hooks under the bottom of the main

unit (shown by arrow

➀

), then slide

the stand in the direction as shown

by arrow

➁

until it stops and the 3

mounting holes are aligned.

Make sure not to put the AC power

cord between the stand and the

unit.

3

Drive Phillips pan screws in the 3

threaded holes at the bottom of the

stand until they are tight.

To remove the stand from this unit

Unscrew the Phillips pan screws indicated by above “

➂

” screw holes. After the screws are removed pull the stand up toward the rear of the

unit. Be careful not to drop the stand when you remove it.

screw holes



front sidefront side







 Symbols Used in this Manual

The following is the description for the symbols used in this manual. Description refers to:

TV

: Analog TV operation

DTV

: Digital TV operation

• If neither symbol appears under the function heading, operation is applicable to both.

6

EN

I

NTRODUCTION

 Contents

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

INTRODUCTION

Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Trademark Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Attaching the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

PREPARATION

Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connection to Cable Receiver or Satellite Box . . . . . . . . . . .9

External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Plug In the AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

WATCHING TV

Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Still Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Switching Each Input Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Switching Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

TV Screen Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

TV Screen Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

OPTIONAL SETTING

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Autoprogram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Add Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Antenna Confirmation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Sound Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

PC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Energy Saving Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Current Software Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

TROUBLESHOOTING

FAQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

INFORMATION

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Cable Channel Designations . . . . . . . . . . . . . . . . . . . . . . . . . . .37

General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Electrical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Other Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

 Features

any storage medium, in any form or for any purpose without the express prior written consent of Funai.

Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the

obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written

consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this

manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein.

Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property

rights to the fullest extent of the law.

• DTV/TV/CATV

- You can use your remote control to select

channels which are broadcast in digital format and

conventional analog format. Also, cable subscribers

can access their cable TV channels.

• Information Display (DTV only)

- You can display the title, contents and other

information of the current DTV program on the TV

screen.

• Autoprogram

- This unit automatically scans and memorizes

channels available in your area, eliminating difficult

setup procedures.

• Child Lock

- This feature allows you to block children’s access to

inappropriate programs.

• Closed Caption Decoder

- Built-in closed caption decoder displays text for

closed caption supported programs.

• MTS/SAP Tuner

- Audio can be selected from the remote control.

• Auto Shut Off Function

- If there is no signal input from the antenna terminal

and no operation for 15 minutes, the unit will turn

off automatically.

• Sleep Timer

- This feature will automatically turn off the power of

the unit at a specific time.

• Choices for On-screen Language

- Select your on-screen language:

English, Spanish or French.

• Stereo Sound Function

• PLL Frequency Synthesized Tuning

- Provides free and easy channel selection and lets

you tune directly to any channel using the number

buttons on the remote control.

• Various Adjustment for Picture and Sound

- Customizes image quality to suitable for your room

and sets the sound as your preference.

• HDMI Input

• Component video Input

• PC Input

• S-Video Input

• AV Input

• Digital audio Output

• Headphone Jack

7

EN

INTRODUCTION PREPARATION

WATCHING TV

OPTIONAL SETTING TROUBLESHOOTING

INFORMATION

1. yy POWER (p. 14)

Press to turn the unit on and off.

2. CHANNEL

+ /

-

(p. 15 / p. 16)

Press to select channels or move up (

+) / down (

-

)

through the main menu items.

3. MENU (p. 19)

Press to display the main menu.

4. VOLUME

+ /

-

(p. 15)

Press to adjust the volume or move right (

+) / left

(

-

) through the main menu items.

5. STAND BY indicator

Lights up red when power is off.

6. POWER ON indicator

Lights up green when power is on.

7. Infrared sensor window

Receives infrared rays transmitted from the remote

control.

[Side Panel]

8. HDMI 2 Input jack (p. 9 / p. 10)

HDMI connection from HDMI device.

9. S-Video Input jack (p. 11)

S-video cable connection from an external device.

10. Video Input jack (p. 12)

RCA video cable connection from an external

device.

11. Audio Input jack (p. 11 / p. 12)

RCA audio cable connection from an external

device.

12. Headphone jack

Headphone connection for personal listening.

[Rear Panel]

13. Antenna Input jack (p. 9)

RF

coaxial cable connection for your antenna or cable

TV signal.

14. AC power cord (p. 13)

Connect to a standard AC outlet to supply power to

this unit.

15. PC Input jack (p. 13)

VGA cable connection from PC.

16. HDMI 1 Input jack (p. 9 / p. 10)

HDMI connection for HDMI or DVI device.

17. Component video and Audio Input jack

(p. 9 / p. 11)

RCA component video cable and RCA audio cable

connection from an external device.

18. Digital audio Output jack (p. 12)

Coaxial digital cable connection for a decoder or an

audio receiver.

19. Audio Input jack for PC connection (p. 13)

Mini-plug audio cable connection from PC.

20. Audio Input jack for HDMI 1 (p. 10)

RCA audio cable connection from a DVI device.

(For HDMI 1 Input jack only)

Note:

*

service terminal (service use only)

• Use this terminal only when a software update is necessary.

• User should not connect any devices to the service terminal

such as digital camera, keyboard, mouse, etc. (because these

will not work).

• The software update is, in most cases, handled by an

authorized service person or in some circumstances the user

may be asked to do the software upgrade themselves.

 Control Panel

 Terminals

HDMI 2

TERMINAL

HEAD PHONE

16

18

17

19

15

14

9

13

12

10

11

20

*

8

+

MENU

VOLUME

CHANNEL

STAND BY

POWER ON

-

+

-

POWER

5

6

7

24

13

8

EN

I

NTRODUCTION

 Remote Control Function

Battery Precautions:

• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.

• Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc, or rechargeable batteries like ni-cad, ni-mh, etc) or

old batteries with fresh ones.

• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

• Do not try to recharge batteries; they can overheat and rupture.

When using a universal remote control

to operate this unit.

• Make sure the component code on your universal

remote control is set to our brand.

Refer to the manual accompanying your remote

control for more details.

7. SAP (p. 16)

Digital mode (DTV)

• Press to select the audio language.

Analog mode (TV)

• Press to select the audio mode.

8. MUTE (p. 15)

Press to turn the sound on and off.

9. VOL + /

-

(p. 15)

Press to adjust the volume.

10. Number buttons (p. 15)

Press to select channels.

•

(dot)

• Press to shift the subchannel from the main channel.

11. FORMAT (p. 18)

Press to select aspect ratio available for the TV screen.

12. MENU (p. 19)

Press to display the main menu.

13. INFO (p. 17)

Digital mode (DTV)

• Press to display the channel information, signal type

and TV setting.

Analog mode (TV)

• Press to display the channel number, signal type and

TV setting.

External input mode

• Press to display the external input modes, signal type

and TV setting.

14. SLEEP (p. 15)

Press to activate the sleep timer.

15. PREV CH (p. 15)

Press to return to the previous channel.

16. CH + /

-

(p. 15 / p. 16)

Press to select channels and the

external input modes.

2

1

3

6

5

4

11

12

13

7

8

15

14

9

10

1

6

 Installing the Batteries

Install the batteries (AAA x 2) matching the polarity indicated inside battery compartment of the remote control.

1.

yy (power) (p. 14)

Press to turn the unit on and off.

2. SOURCE (p. 16)

Press to access connected external devices like a

BD/DVD recorder.

3. FREEZE (p. 16)

Press to pause screen image.

4.

s

/

B

/

K

/

L

(cursor) (p. 14)

Press to move left / right / up / down through the

items.

5. OK (p. 14)

Press to decide the command of setting when the

main menu is displayed.

6. BACK (p. 17)

Press to return to the previous menu operation.

AAA

9

EN

P

REPARATION

INTRODUCTION

PREPARATION

WATCHING TV

OPTIONAL SETTING TROUBLESHOOTING

INFORMATION

Before you connect...

Be sure your antenna or other device is connected properly before plugging in the AC power cord.

 Antenna Connection

Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.

or

* Once connections are completed, turn on the unit and begin initial setup. Channel scanning is necessary for the unit

to memorize all available channels in your area. Refer to “Initial Setup” on page 14.

Note:

• If you have any question about the DTV’s antenna, visit www.antennaweb.org for further information.

• Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters). Contact your local

electronics store for these items.

• For your safety and to avoid damage to this unit, please unplug the RF coaxial cable from the antenna input jack before moving the unit.

• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than

settop versions.

• To switch your reception source easily between antenna and cable, install an antenna selector.

• If you connect to the cable system directly, contact the CATV installer.

 Connection to Cable Receiver or Satellite Box

Use an HDMI or an RCA component video cable to connect the HDMI or the Component video Input jack of the unit to the

HDMI or the component video output jack of the cable receiver / satellite box.

If you connect to the unit’s Component video Input jack, connect RCA audio cables to the Audio L/R jacks next to the

Component video connector.

HDMI 2

COMPONENT VIDEO OUT

Pr/CrPb/CbY

AUDIO OUT

RL

STEREO

PCM

HDMI OUT

ANT IN

* You can also connect this unit to the cable receiver or satellite box other than the HDMI or the component video

output jack because they might have different output jacks.

* Required cables and connecting methods of the cable receiver / satellite box, or the availability channel for the

clear QAM may differ depending on the cable / satellite provider. For more information, please contact your cable /

satellite provider.

No supplied cables are used in this connection:

Please purchase the necessary cables at your local store.

High Speed HDMI cable (also known as HDMI category 2 cable) is recommended for the better compatibility.

VHF / UHF

antenna

RF coaxial cable

cable TV signal

rear of this unit

e.g.)

or

satellite dish

(green)(green)

cable receiver / satellite box

cable TV signal

including PPV

or

side or

rear of this unit

HDMI cable

or

RCA component video cable

and RCA audio cable

RF coaxial

cable

e.g.)

(red)(red)

(red)

(blue)(blue)

(blue)

(green)(green)

(green)

(red)(red)

(red)

(blue)(blue)

(blue)

(green)

or

10

EN

P

REPARATION

 External Device Connection

[HDMI Connection]

HDMI connection offers the highest picture quality.

HDMI (High-Definition Multimedia Interface) transports high definition video and multi-channel digital audio

through a single cable.

e.g.)

HDMI 2

HDMI OUT

CHAPTER 15

REPEAT A-B

TITLE 5

Note:

• This unit accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.

• This unit accepts only 2 channel audio signal (LPCM).

• You need to select “PCM” for the digital audio of the device you connected or check the HDMI audio setting.

There may be no audio output if you select “Bitstream”, etc.

• This unit only accepts signals in compliance with EIA861.

[HDMI-DVI Connection]

Use an HDMI-DVI conversion cable to connect the unit to external video devices equipped with DVI output jack.

e.g.)

STEREO

PCM

DVI OUT

AUDIO OUT

RL

Note:

• This unit accepts 480i / 480p / 720p / 1080i video signals.

• HDMI-DVI connection requires separate RCA audio connections as well.

• Audio signals are converted from digital to analog for this connection.

• DVI does not display 480i image that is not in compliance with EIA/CEA-861/861B.

No supplied cables are used in this connection:

Please purchase the necessary cables at your local store.

High Speed HDMI cable (also known as HDMI category 2 cable) is recommended for the better compatibility.

HDMI cable

BD/DVD recorder

with the HDMI output jack

side or

rear of this unit

or

To HDMI1

input jack only

HDMI-DVI conversion cable

cable receiver or satellite box

with the DVI output jack

RCA audio cable

rear of this unit

11

EN

INTRODUCTION

PREPARATION

WATCHING TV

OPTIONAL SETTING TROUBLESHOOTING

INFORMATION

[Component video Connection]

RCA component video connection offers better picture quality for video devices connected to the unit.

If you connect to the unit’s Component video Input jack, connect RCA audio cables to the Audio L/R jacks next to the

Component video connector.

e.g.)

COMPONENT VIDEO OUT

Pr/CrPb/CbY

AUDIO OUT

RL

CHAPTER 15

REPEAT A-B

TITLE 5

Note:

• This unit accepts 480i / 480p / 720p / 1080i video signals.

[S-Video Connection]

S-Video connection offers good picture quality for video devices connected to the unit.

If you connect to the unit’s S-Video Input jack, connect RCA audio cables to the Audio L/R jacks below the Video

connector.

e.g.)

CHAPTER 15

REPEAT A-B

TITLE 5

AUDIO OUT

RL

S-VIDEO

OUT

Note:

• If you connect to the S-Video Input jack and the Video Input jack at the same time, the S-Video connection will have priority.

No supplied cables are used in this connection:

Please purchase the necessary cables at your local store.

(green)(green)

(blue)(blue)

(red)(red)

(red)(blue)(green)

BD/DVD recorder with

the component video output jack

RCA component

video cable

RCA audio cable

rear of this unit

(green)

(blue)

(red)

BD/DVD recorder with

the S-Video output jack

S-Video cable

RCA audio cable

side of this unit

12

EN

P

REPARATION

[Video Connection]

RCA video connection offers standard picture quality for video devices connected to the unit.

If you connect to the unit’s Video Input jack, connect RCA audio cables to the Audio L/R jacks below the Video

connector.

When the audio jack of the video device is monaural, connect an RCA audio cable to the audio L Input jack.

e.g.)

AUDIO OUT

RL

VIDEO

OUT

STEREO

STAND-BY

Note:

• If you connect to the S-Video Input jack and the Video Input jack at the same time, the S-Video connection will have priority.

[Audio Output Connection (for digital broadcasting only)]

If you connect this unit to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital

broadcasting sound.

Use a digital audio coaxial cable to connect the unit to external digital audio devices.

e.g.)

DIGITAL AUDIO

COAXIAL IN

No supplied cables are used in this connection:

Please purchase the necessary cables at your local store.

camcorder video game

VCR

RCA video cable

RCA audio cable

side of this unit

Dolby Digital

decoder

digital audio coaxial cable

rear of this unit

13

EN

INTRODUCTION

PREPARATION

WATCHING TV

OPTIONAL SETTING TROUBLESHOOTING

INFORMATION

[PC Connection]

This unit is equipped with a PC input jack. If you connect this unit to your PC, you can use this unit as a PC monitor.

Use an VGA cable for this connection and it requires stereo mini-plug Audio cable as well.

e.g.)

The following signals can be displayed:

Format Resolution Refresh rate Format Resolution Refresh rate

VGA 640 x 480 60Hz

WXGA

1,280 x 768 60Hz

SVGA 800 x 600 60Hz

1,360 x 768 60Hz

XGA 1,024 x 768 60Hz

Other formats or non-standard signals will not be displayed correctly.

Note:

• Please purchase the VGA cable that has a ferrite core.

• The following operations may reduce noise.

- Attach a ferrite core to the AC power cord of your PC.

- Unplug the AC power cord and use the built-in battery of your PC.

 Plug In the AC Power Cord

Make sure that the AC power cord must be plugged to an AC outlet after all the necessary connections are completed.

Caution:

• Do not connect the AC power cord to a power supply outside the indicated voltage of this unit (AC 120V).

Connecting the AC power cord to a power supply outside of this range may result in fire or electrical shocks.

Note:

• Each time you plugged in the AC power cord, any operations will not be performed for a few seconds. This is not a malfunction.

No supplied cables are used in this connection:

Please purchase the necessary cables at your local store.

rear of this unit

AC power cord

AC outlet

stereo mini-plug audio cable

VGA cable

rear of this unit

VGA cable should be

with ferrite core.

personal computer

14

EN

P

REPARATION

 Initial Setup

This section will guide you through the unit’s initial setting which includes

selecting a language for your on-screen menu and autoprogram, which

automatically scans and memorizes viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cable.

1

After making all the necessary connections,

press [y y (power)] to turn on the unit.

• This operation may take a few moments.

2

Use [Cursor

K

/

L

] to select the on-screen language

from the choices on the right side of the TV screen.

(English / Español / Français)

Initial Setup

Select the language for setup display.

Elija el idioma de ajuste.

Sélectionner langue écran config.

Español

Français

Select Skip

MENU

OK

English

• “Initial Setup” menu on step 3 will be displayed in the

selected language after you press [OK].

3

Use [Cursor

K

/

L

] to select “Antenna” for TV channels

or “Cable” for CATV channels, then press [OK].

Initial Setup

Cable

Antenna

Or

Select Skip

MENUBACK

BackOK

OK

Make sure the antenna is connected to ''ANT. IN'' jack.

Select your signal source.

Cable

Skip

Antenna

ANT.IN

• “Autoprogram” will begin.

Initial Setup

Now the system is scanning for channels, please wait.

Auto programming will take up to 20 minutes to complete.

Skip

MENU

0%

Analog channels 0ch

Digital channels 0ch

4

Use [Cursor

s

/

B

] to select the desired location setting,

then press [OK].

Initial Setup

Select “Retail” or “Home” for your location.

OK

Retail

Home

Select

• Select ”Retail”, the unit will be set up with predefined

setting for retail displays. In this setting, the power

consumption may possibly exceed the limited

requirement of the ENERGY STAR® qualification.

• Select ”Home”, the unit is set to maximize the energy

efficiency for home setting and it can be adjusted

through a choice of picture and sound quality

according to your preference.

• When the initial setup is completed, the lowest

memorized channel with the confirmation message

of the location setting will be displayed on the TV

screen.

Note:

• If you connect the cable system directly, contact the CATV

installer.

• If you press [yy (power)] or [MENU] during autoprogram,

this setting will be canceled.

• The initial autoprogram function can be executed for

either “Antenna” or “Cable” only once. When you change

the connection (Antenna / Cable), set autoprogram again.

Refer to page 19.

• If there is no signal input from the antenna terminal and

no operation for several seconds after you turn on the unit,

“Helpful Hints” appears. Follow the instructions listed on

the TV screen.

Initial Setup

Select Skip

MENU

No channel is registered.

Try Autoprogram again?

Verify that you have a cable connected to the "ANT. IN" jack on the

back of the TV, the channel installation process searches this

connection. If you are using a cable or satellite box, please confirm

the input which you have connected the box and press "SOURCE"

key on the remote control to select the appropriate source input.

Later

Retry

OK

• You must set ”Home” in step 4. Otherwise, the settings

of picture and sound quality you adjusted will not be

memorized after you turn off the unit.

After an initial setup is completed...

• If you want to scan the channels automatically again,

refer to “Autoprogram” on page 19.

• You can add the desired channels unmemorized by

“Autoprogram”. Refer to “Add Channels” on page 20.

• If you want to change to another language, refer to

“Language Selection” on page 21.

• If you want to change the location setting, refer to

“Location” on page 32.

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

15

EN

W

ATCHING TV

INTRODUCTION

PREPARATION WATCHING TV

OPTIONAL SETTING TROUBLESHOOTING

INFORMATION

 Channel Selection

Select channels by using [CH + /

-

] or [the Number buttons].

• To select the memorized channels, use [CH + /

-

] or

[the Number buttons].

• To select the non-memorized channels, use

[the Number buttons].

To Use [the Number buttons]

TV

- When selecting analog channel 11

DTV

- When selecting digital channel 11.1

Be sure to press [

•

] before

entering the subchannel number.

• Press [PREV CH] to return to the previously viewed

channel.

About digital TV broadcasting:

With its high definition broadcast, digital broadcasting

far surpasses analog broadcasting in both its picture

and sound quality. Not all digital TV broadcasts are high

definition (HD). To confirm whether your watching TV

program is in HD, refer to the program guide, contact

your cable / satellite provider or local TV stations.

NTSC

(analog mode)

ATSC

(digital mode)

6:00pm

6:30pm

7:00pm

7:30pm

8:00pm

CH4-1

(Soccer)

CH4-2

(News)

CH4-3

(Tennis)

CH4-1

(Soccer)

CH4

(Soccer)

CH4

(Soccer)

CH4-1

(Soccer)

CH4-2

(News)

CH4

(Soccer)

CH4

(Soccer)

CH4-1

(Soccer)

Air time

subchannelsubchannel

main channel

subchannel

What is the subchannel?

By using high compression technology, digital

broadcasting offers a service that enables multiple

signals to send simultaneously.

Therefore, you can select more than one program per

main channel since digital broadcasting technology

distinguishes between multiple channels broadcast by

a single network.

Note:

• “No Signal” will appear on the TV screen after the

subchannel broadcast is over.

• “Audio only program“ message will appear on the TV

screen, when you receive only sound signal.

 Volume Adjustment

This section describes how to adjust the volume. The mute function, which

turns the sound off and on, is also described.

Use [VOL + /

-

] to adjust the audio volume.

Volume 30

The volume bar will be displayed at the bottom of the

TV screen when adjusting the volume.

• The volume bar will automatically disappear in a few

seconds.

Press [MUTE] to turn off and on the sound.

Mute

“Mute” is displayed on the TV screen for a few seconds.

Press [MUTE] again or [VOL + /

-

] to recover the

original volume.

 Sleep Timer

The sleep timer can be set to automatically turn off the unit after an

incremental period of time.

1

Press [SLEEP] to set the sleep timer.

Sleep

Off

Sleep timer display appears on the TV screen.

2

Press [SLEEP] repeatedly to change the amount of time

until shut off.

Sleep

120min.

You can set your unit to turn off after a set period of

time (from 30 to 120 minutes).

• Each press of [SLEEP] will increase the time by 30

minutes.

• After setup, the sleep timer display can be called up

for checking by pressing [SLEEP].

To cancel the sleep timer

Press [SLEEP] repeatedly until “Sleep Off” is displayed

on the TV screen.

Note:

• The sleep timer display will automatically disappear in a

few seconds.

• When you disconnect the unit from the AC outlet or when

a power failure occurs, the sleep timer setting will be

canceled.

can be changed by using [CH + /

-

].

16

EN

W

ATCHING TV

 Still Mode

You can pause the image shown on the TV screen.

Press

[FREEZE] to pause the image shown on the TV

screen.

FREEZE

• The sound output will not be paused.

• If no signal is detected or protected signal is received

during still mode, the image remains paused and the

sound output will be muted.

• The still function will be released after 5 minutes.

To cancel still mode, press any button except

[y y (power)].

 Switching Each Input Mode

You can easily switch with the remote control to the DTV (ATSC) and TV

(NTSC) or to access external devices when they are connected to the unit.

Press [SOURCE] or [CH +] repeatedly to cycle through

the input modes.

PC

Video

Component

HDMI1

HDMI2

Source

TV

Video

Component

HDMI1

HDMI2

PC

DTV/TV channel

• Pressing [CH

-

] reverses the direction of the input

modes.

 Switching Audio Mode

This section describes how to switch the audio in the analog mode and how

to switch the audio language in the digital mode.

TV

Press [SAP] to display the currently selected audio

mode. While receiving an MTS broadcast, press

repeatedly to cycle through the available audio

channel.

11

SAP / STEREO

When all audio are available

SAP / STEREO SAP / MONO

SAP / STEREO

When stereo and monaural audio are available

MONO / STEREO MONO / STEREO

When SAP and monaural audio are available

SAP / MONO SAP / MONO

When only monaural audio is available

MONO

STEREO : Outputs stereo-audio

SAP : Outputs second audio program

MONO : Outputs mono-audio

DTV

1

Press [SAP] to display the currently selected language

and the number of available languages.

11.1

English 1/3

2

Press [SAP] repeatedly to cycle through the available

audio languages.

• Available languages differ depending on the

broadcast. “Other” is displayed when the audio

language cannot be acquired, or the acquired

languages are other than English, Spanish or French.

Note:

• [SAP] does not control external audio devices.

• The information display will automatically disappear in a

few seconds.

(cannot be switched)

17

EN

INTRODUCTION

PREPARATION WATCHING TV

OPTIONAL SETTING TROUBLESHOOTING

INFORMATION

 TV Screen Information

You can display the currently selected channel or other information such as

the audio mode on the TV screen.

TV

In the analog mode, the current channel number and the audio mode are

displayed.

Press [INFO].

11

SAP / STEREO

TV-PG DLSV

480i

4:3

SD

CC

• The current channel number, audio mode, type of

resolutions for video signal, TV aspect ratio, CC and

TV program rating are displayed on the top-right

corner of the TV screen.

• To clear the display, press [INFO] again. You can also

press [BACK].

DTV

In the digital mode, the detailed broadcasting information for the current

channel such as program title, program guides are displayed.

Press [INFO] to display the details of the currently

selected program.

Broadcasting information

The following information is displayed.

11.1

English 1/2

TV: TV-14

Rating

1080i

16:9

HD

CC

A Day of Memories

KABC

A quarter-century ago,which may now qualify as the

good old days of newspapering,run-of-paper sales

accounted for 80 percent of the industry's advertising

revenues.Department stores and supermarket were

1 2

34

5

6, 7, 8

9

10

1 program title

2 program guide

(The program guide added to broadcasting

information is displayed to a maximum of 4 lines.)

3 broadcast station

4 channel number

5 audio language

Refer to “Switching Audio Mode” on page 16.

6 effective scanning lines and scan mode

7 digital TV format

8 program aspect ratio

9 CC (not available if closed caption is set to “Off”)

10 child lock rating

Note:

• When the program guide consists of more than 4 lines, use

[Cursor K/ L] to scroll.

• “No description provided.” is displayed when the program

guide is not provided.

• While the program guide is displayed, the closed caption

function is interrupted.

• In external input mode, the following screen is displayed;

e.g.) When an external device is connected to Video Input

jack.

Video

TV-PG DLSV

480i

SD

CC

• The information display will automatically disappear in

1 minute.

18

EN

W

ATCHING TV

 TV Screen Display Mode

4 types of display modes can be selected when the broadcasting station

is sending 4:3 or 16:9 video signal. And 3 types of display modes can be

selected for PC input signal.

Press [FORMAT] repeatedly to switch the TV aspect

ratio.

For 4:3 video signal

Normal

Display a 4:3 picture at its original size. Sidebars appear

on both edges of the screen.

16:9

Display a 4:3 picture at a 16:9 size; the picture is

stretched horizontally to fill the screen.

Movie Expand

Display a 4:3 picture at a 16:9 size; the picture is

stretched horizontally and vertically to fill the screen.

This crops out the top and bottom of the picture.

Wide

Display the picture with its center at the original size

and the edges stretched horizontally to fill the screen.

For 16:9 video signal

Normal

Display a 16:9 picture at its original size.

Zoom

Display a 16:9 picture at its maximum size without

changing its horizontal and vertical ratio.

Movie Expand

Display a vertically stretched picture.

Wide

Display a horizontally stretched picture.

For PC input signal

Normal

Display a proportionately stretched picture. Sidebars

appear on both edges of the screen.

Full

Display a picture that is stretched out of proportion to

fill the screen.

Dot By Dot

Display a picture in its original size.

Normal Full

Dot By Dot

Normal

16:9

Wide

Movie Expand

Normal

Zoom

Wide

Movie Expand

19

EN

O

PTIONAL SETTING

INTRODUCTION

PREPARATION

WATCHING TV

OPTIONAL SETTING

TROUBLESHOOTING

INFORMATION

 Main Menu

This section describes the overview of the main menu displayed when you

press [MENU]. For more details, see the reference page for each item.

The main menu consists of the function setting items below.

Press [MENU].

PICTURE

SOUND

SETUP

FEATURES

LANGUAGE

Tint

Sharpness

Brightness

Contrast

Color

0

30

60

36

Color Temperature

Smart Picture

Normal

Personal

PICTURE

You can adjust the picture quality.

Refer to “Picture Adjustment” on page 22.

SOUND

You can adjust the sound quality.

Refer to “Sound Adjustment” on page 23.

SETUP

• You can automatically scan the viewable channels.

Refer to “Autoprogram” on page 19.

• You can skip the undesired channels when selecting

the channels using [CH

+ /

-

].

Refer to “Channel List” on page 20.

• You can add the channels that were not scanned by

the autoprogram.

Refer to “Add Channels” on page 20.

FEATURES

• You can change the display format for closed

caption, which displays the dialogue of a TV program

or other information across the TV screen.

Refer to “Closed Caption” on page 24.

• You can set the viewing limitations.

Refer to ‘‘Child Lock” on page 27.

• You can adjust the position, stability and clarity of the

PC screen.

Refer to “PC Settings” on page 30.

• You can select the energy saving mode.

Refer to “Energy Saving Mode” on page 31.

• When you adjust the desired “PICTURE” and

“SOUND” mode, you must switch the setting from

“Retail” to “Home”. Refer to “Location” on page 32.

• You can confirm the version of the software currently

used in this unit.

Refer to ”Current Software Info” on page 32.

LANGUAGE

You can change the language (English, Spanish,

French) displayed on the main menu.

Refer to “Language Selection” on page 21.

 Autoprogram

If you switch wires (e.g., between antenna and CATV) or if you move the

unit to a different area after the initial setting, or if you restore the DTV

channel you deleted, you will need to perform autoprogram.

Before you begin: Make sure the unit is connected to antenna or cable.

1

Press [MENU] to display the main menu.

2

Use [Cursor K

/

L] to select “SETUP”, then press [OK].

Channel List

Add Channels

Antenna

PICTURE

SOUND

FEATURES

LANGUAGE

SETUP

Autoprogram

3

Use [Cursor K

/

L] to select “Autoprogram”, then press

[OK].

Channel List

Add Channels

Antenna

Autoprogram

PICTURE

SOUND

FEATURES

LANGUAGE

SETUP

Use [Cursor K

/

L] to select an appropriate option, then

press [OK].

Antenna

Cable

Back

Autoprogram will rescan all channels.

Autoprogramming will take up to 20 minutes

to complete.

Select your signal source.

PICTURE

SOUND

FEATURES

LANGUAGE

SETUP

Antenna

Cable

Or

ANT.IN

• When aerial antenna is connected, select “Antenna”.

• When connected to CATV, select “Cable”.

• “Autoprogram” will begin.

• When the scanning and memorizing are completed,

the lowest memorized channel will be displayed.

Note:

• After setting “Autoprogram”, using [CH + /

-

] on the remote

control skips unavailable programs automatically.

• If you connect the cable system directly, contact the CATV

installer.

• If you press [

yy (power)] or [MENU] during autoprogram,

the setting will be canceled.

• Even if “Autoprogram“ is completed, the channel setting

will be lost if the AC power Code is unplugged before

turning off the unit by pressing [yy (power)].

• The PIN Code will be required once you set a PIN Code in

the “Child Lock”. Refer to page 27.

• If you want to change your PIN Code, follow the instruction

of “Change PIN”. Refer to page 30.

Exit

MENU

75%

Analog channels 10 ch

6 chDigital channels

Now the system is scanning for channels, please wait.

Auto programming will take up to 20 minutes to complete.

20

EN

O

PTIONAL SETTING

 Channel List

The channels selected here can be skipped when selecting the channels

using [CH + /

-

].

Those channels can still be selected with [the Number buttons].

1

Press [MENU] to display the main menu.

2

Use [Cursor K

/

L] to select “SETUP”, then press [OK].

Channel List

Add Channels

Antenna

Autoprogram

PICTURE

SOUND

FEATURES

LANGUAGE

SETUP

3

Use [Cursor K

/

L] to select “Channel List”, then press

[OK].

PICTURE

SOUND

FEATURES

LANGUAGE

SETUP

Channel List

Add Channels

Antenna

Autoprogram

4

Use [Cursor K

/

L] to select the channel you want to

remove, then press [OK].

Ch Select Watch/Skip

Back

BACK

OK

Highlight channels for Ch Up/Down key

selection.

11.2

11.3

DTV

PICTURE

SOUND

FEATURES

LANGUAGE

SETUP

DTV 11.1

• The channel display for the removed channel

darkens. You will not be able to select the channel

again using [CH

+ /

-

].

• To reactivate a removed channel, use [Cursor K

/

L] and

press [OK]. The registered channels are highlighted.

• When you remove a main channel, its subchannels

are removed as well.

Note:

• The channel with the “DTV” indicated on the display is

ATSC. Otherwise the channel is NTSC.

5

Press [MENU] to exit.

 Add Channels

This function lets you add the channels that were not added by the

autoprogram due to the receptible condition at the initial setting.

1

Press [MENU] to display the main menu.

2

Use [Cursor K

/

L] to select “SETUP”, then press [OK].

Channel List

Add Channels

Antenna

Autoprogram

PICTURE

SOUND

FEATURES

LANGUAGE

SETUP

3

Use [Cursor K

/

L] to select “Add Channels”, then press

[OK].

Channel List

Add Channels

Antenna

Autoprogram

PICTURE

SOUND

FEATURES

LANGUAGE

SETUP

4

Use [the Number buttons] to enter the number of the

channel you want to add, then press [OK].

11

For analog channels, select a channel to be

added using number keys.

For digital channels, you must perform

Autoprogram function.

Add channels

Ch Change

Back

BACK

PICTURE

SOUND

FEATURES

LANGUAGE

SETUP

5

Press [MENU] to exit.

Note:

• If setup completes successfully,

“Added to the channel list” is displayed.

• If external input is used, it is not possible to register the

channel and “Unavailable” will be displayed on the TV

screen.

• By using [CH + /

-

], you can select the memorized

channels only.

La page charge ...

Magnavox 19MF339B Le manuel du propriétaire

Ce manuel convient également à

Magnavox 19MF339B Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents