Dell PowerEdge C6105 Le manuel du propriétaire

Dell PowerEdge

C6105

Getting Started

With Your System

Guide de mise en route du système

Introdução ao Uso do Sistema

Introducción al sistema

Dell PowerEdge

C6105

Getting Started

With Your System

Notes, Cautions, and Warnings

NOTE:

A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of

data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

______________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission

of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of

Dell Inc. AMD® is a registered trademark and AMD Opteron™ is a trademark of

Advanced Micro Devices, Inc. Red Hat Enterprise Linux® and Enterprise Linux® are

registered trademarks of Red Hat, Inc. in the United States and/or other countries.

Novell® is a registered trademark and SUSE™ is a trademark of Novell Inc. in the United

States and other countries. Citrix® and XenServer® are either registered trademarks or

trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware®

is a registered trademarks or trademarks of VMWare, Inc. in the United States or other

countries.

Other trademarks and trade names may be used in this publication to refer to either the

entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Regulatory Model B03S

November 2013 P/N 45F0M Rev. A05

Getting Started With Your System | 3

CAUTION: Restricted Access Location

This server is intended for installation only in restricted access locations as

defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply:

•

Access can only be gained by service persons or by users

who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.

•

Access is through the use of a tool or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

Installation and Configuration

WARNING: Before performing the following procedure, review and follow the

safety instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Tool-Less Rail Solution

WARNING: Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

WARNING: The system is not fixed to the rack or mounted on the rails. To

avoid personal injury or damage to the system, you must adequately

support the system during installation and removal.

WARNING: To avoid a potential electrical shock hazard, a third wire safety

grounding conductor is necessary for the rack installation. The rack

equipment must provide sufficient airflow to the system to maintain proper

cooling.

CAUTION: When installing rails in a square-hole rack it is important to

ensure that the square peg slides through the square holes.

Getting Started With Your System | 4

1

Align the end pieces of the rails on the vertical rack flanges to seat

the pegs in the bottom hole of the first U and the top hole of the

second U. Engage the back end of the rails until the latches lock in

place.

NOTE:

The rails can be used in both square-hole (item 1 in the following figure)

and round-hole racks (item 2 in the following figure).

Figure 1. Pushing the Latch Release Buttons

2

Repeat Step 1 to position and seat the front end pieces on the vertical

flanges.

NOTE:

To remove the rails, pull on the latch release button on the end piece

midpoint and unseat each rail.

3

Slide the system into the rack.

4

If present, remove the chassis stabilizer shipping bracket (optional)

from the rack.

NOTE:

To transport systems already installed in the rack, ensure that the two

chassis stabilizer shipping brackets (optional) are in place.

Getting Started With Your System | 5

Figure 2. Installing the Chassis Stabilizer Shipping Brackets

5

Tighten the thumbscrews to secure the ears of the system to the front

of the rack flanges.

Figure 3. Installing the Chassis onto the Rack.

Getting Started With Your System | 6

Optional-Connecting the Keyboard, Mouse, and Monitor

Figure 4. Optional—Connecting the Keyboard, Mouse and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to

plug into each connector. Be sure to tighten the screws (if any) on the monitor’s

cable connector.

Getting Started With Your System | 7

Connecting the Power Cable(s)

Figure 5. Connecting the Power Cable

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor. Plug the other end of the

power cables into a grounded electrical outlet or a separate power source such as

an uninterrupted power supply or a power distribution unit.

Getting Started With Your System | 8

Turning on the System

Figure 6. Pressing the Power Button on the Front of the System and the Monitor

Figure 7. Pressing the Power Button on the Back of the System

Press the power button(s) either on the front or back of the system and on the

monitor. The power indicators should light.

Getting Started With Your System | 9

Complete the Operating System Setup

To install an operating system for the first time, see the installation and

configuration documentation for your operating system. Be sure the operating

system is installed before installing hardware or software not purchased with the

system.

NOTE:

For the latest information on supported operating systems, see

dell.com/ossupport.

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

The Hardware Owner’s Manual provides information about system features and

describes how to troubleshoot the system and install or replace system

components. This document is available at

dell.com/support/manuals

.

Dell systems management application documentation provides information

about installing and using the systems management software. This document is

available online at

dell.com/support/manuals

.

NOTE:

Always check for updates on

dell.com/support/manuals

and read the

updates first because they often supersede information in other documents.

Getting Started With Your System | 10

NOM Information (Mexico Only)

The following information is provided on the device described in this document

in compliance with the requirements of the official Mexican standards (NOM):

Importer Dell Inc. de México, S.A. de C.V.

Paseo de la Reforma 2620-11° Piso

Col. Lomas Atlas

11950 México, D.F.

Model number

B03S

Supply voltage 100-240 V AC with 470 W/750

W/1100 W Power

200-240 V AC with 1400 W Power

Frequency

50/60 Hz

Current consumption 6.5-3.5 Amps with 470 W Power

8.6 Amps with 1400 W Power

9.5-5.0 Amps with 750 W Power

12-6.7 Amps with 1100 W Power

Getting Started With Your System | 11

Technical Specifications

Processor (Per System Board)

Processor type One or two AMD C32 Series processors

One or two AMD Opteron 4000 Series

processors

One or two AMD Opteron 4200 Series

processors

One or two AMD Opteron 4300 Series

processors

Expansion Bus (Per System Board)

Bus type

PCI Express Generation 2

Expansion slots

PCIe

One x16, half-length, half-height

Daughter card PCIe

One x8, custom slot

Memory (Per System Board)

Architecture 12 x DDR3 800/1066/1333/1600* MHz

registered memory modules with /ECC

Memory module sockets

12 x DDR3 DIMM sockets

Memory module capacities 2 GB, 4 GB, 8 GB, or 16 GB

Minimum RAM 12 GB

Maximum RAM

192 GB

NOTE:

System memory working frequency is up to 1333MT/s only.

Drives

Hard drives Up to twelve 3.5-inch, hot-swappable

SAS/SATA drives or up to twenty four 2.5-

inch, hot-swappable SAS/SATA/SSD drives

NOTE:

SAS hard drives are supported by add-on card.

Getting Started With Your System | 12

Connectors (Per System Board)

Back

NIC

Two RJ-45 (10/100/1000 Mbps Ethernet)

Serial

9-pin, DTE, 16550-compatible

USB Two 4-pin, USB 2.0-compliant

Video

15-pin D-Sub VGA

Management port Dedicated Ethernet port for remote

management access

Video (Per System Board)

Video type On-board AST2050 video controller or

AST1100

Video memory

8 MB

Power

AC power supply (per power supply)

Wattage 470 W

Voltage

100-240 VAC, 50-60 Hz, input current

range: 6.5-3.5 Amps

Heat dissipation 2390 BTU/hr maximum

Wattage

750 W

Voltage 100-240 VAC, 50-60 Hz, input current

range: 9.5-5.0 Amps

Heat dissipation

3414 BTU/hr maximum

Wattage

1023 W low line/1100W high line

Voltage 100-240 VAC, 50-60 Hz, input current

range: 12.0-6.7 Amps

Heat dissipation

4575 BTU/hr maximum

Wattage 1400 W

Voltage

200-240 VAC, 50-60 Hz, maximum input

current: 9.6 Amps

Heat dissipation 5432 BTU/hr maximum

Getting Started With Your System | 13

Maximum inrush current Initial In-rush Current cannot exceed 55

Amps (peak). Secondary In-rush Current

cannot exceed 35 Amps (peak).

Battery (per system board)

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

3.7-V lithium ion battery pack

Physical

Height

8.76 cm (3.45 in)

Width 44.8 cm (17.6 in)

Depth 75.1 cm (29.47 in)

Weight (maximum

configuration)

33.67 kg (74.2 lb)

Weight (empty) 15.11 kg (33.32 lb)

Environmental

NOTE:

For additional information about environmental measurements for specific system

configurations, see

www.dell.com/environmental_datasheets

.

Temperature

Operating 10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

Storage –40° to 65°C (–40° to 149°F) with a

maximum temperature gradation of 20°C per

hour

Relative humidity

Operating 20% to 80% (noncondensing) with a

maximum humidity gradation of 10% per

hour

Storage

5% to 90% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz

Storage

1.93 Grms at 10–500 Hz for 15 min

Getting Started With Your System | 14

Maximum shock

Operating One shock pulse in the positive z axis

(one pulse on each side of the system) of

31 G for 2.6 ms in the operational orientation

Storage Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of

71 G for up to 2 ms;

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system)

of 27 G faired square wave pulse with

velocity change at 235 inches/second

(597 centimeters/second)

Altitude

Operating –16 to 3,048 m (–50 to 10,000 ft)

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Airborne contaminant level

Class

G2 or lower as defined by ISA-S71.04-1985

Dell PowerEdge

C6105

Guide de mise en

route du système

Remarques, précautions et

avertissements

REMARQUE

: indique des informations importantes qui peuvent vous aider à mieux

utiliser votre ordinateur.

PRÉCAUTION : une PRÉCAUTION indique un risque d'endommagement du

matériel ou de perte de données en cas de non respect des instructions.

AVERTISSEMENT : un AVERTISSEMENT indique un risque

d'endommagement du matériel, de blessure corporelle ou de mort.

Les informations contenues dans ce document peuvent être modifiées sans préavis.

La reproduction du présent document, de quelque manière que ce soit, sans l'autorisation

écrite de Dell Inc. est strictement interdite.

Les marques utilisées dans ce document : Dell™, le logo DELL logo et PowerEdge™ sont

des marques de Dell Inc. AMD® est une marque déposée et AMD Opteron™ est une

marque d'Advanced Micro Devices, Inc. Red Hat Enterprise Linux® et Enterprise Linux®

sont des marques déposées de Red Hat, Inc. aux États-Unis et/ou dans d'autres pays.

Novell® est une marque déposée et SUSE™ est une marque de Novell Inc. aux États-Unis

et dans d'autres pays. Citrix® et XenServer® sont des marques déposées ou des marques

de Citrix Systems, Inc. aux États-Unis et/ou dans d'autres pays. VMware® est une marque

déposée ou une marque de VMware, Inc. aux États-Unis ou dans d'autres pays.

D'autres marques et noms de marque peuvent être utilisés dans ce document pour faire

référence aux entités se réclamant de ces marques et de ces noms ou de leurs produits.

Dell Inc. décline tout intérêt exclusif dans les marques et les noms commerciaux autres

que les siens.

Modèle réglementaire B03S

Novembre 2013 P/N 45F0M Rév. A05

Guide de mise en route du système | 17

PRÉCAUTION : Zone à accès restreint

Ce serveur est conçu pour être installé uniquement dans des zones à

accès restreint telles que définies selon la norme Cl. 1.2.7.3 de IEC

60950-1: 2001 où ces deux conditions s'appliquent :

•

Seuls peuvent avoir accès le personnel d'entretien et les utilisateurs

qui ont été informés des motifs des restrictions appliquées à

l'emplacement et des précautions à prendre.

•

L'accès, qui se fait par l'intermédiaire d'un outil ou d'un verrou et

d'une clé, ou par d'autres moyens de sécurité, est contrôlé par le

responsable en charge de l'emplacement.

Installation et configuration

AVERTISSEMENT : avant de commencer la procédure suivante, lisez et

respectez les consignes de sécurité fournies avec le système.

Déballage du système

Sortez le système de son emballage et identifiez chaque élément.

Installation des rails sans outils

AVERTISSEMENT : demandez toujours de l'aide avant de soulever le

système. N'essayez pas de le soulever seul, car vous risqueriez de vous

blesser.

AVERTISSEMENT : le système n'est fixé ni au rack ni aux rails. Vous devez

le soutenir correctement au cours de l'installation et du retrait pour éviter

de l'endommager ou de vous blesser.

AVERTISSEMENT : afin d'éviter une éventuelle électrocution, assurez-vous

de disposer d'un troisième conducteur de mise à la terre pour l'installation

du rack. L'équipement du rack doit assurer une ventilation suffisante pour

bien refroidir le système.

PRÉCAUTION : lorsque vous installez des rails dans un rack à trous

carrés, vérifiez que les taquets de fixation à tête carrée glissent bien dans

les trous carrés.

Guide de mise en route du système | 18

1

Alignez l'embout des rails sur les collerettes verticales pour

que les taquets de fixation s'insèrent dans le trou du bas de la

première unité en U et le trou du haut de la deuxième unité

en U. Glissez l'arrière du rail jusqu'à enclenchement du

loquet.

REMARQUE :

les rails peuvent aussi bien être utilisés dans un rack à trous

carrés (élément 1 dans la figure ci-dessous) que dans un rack à trous ronds

(élément 2 dans la figure ci-dessous).

Figure 1. Appuyer sur les boutons de dégagement du loquet

2

Répétez

l'étape 1

pour positionner et fixer les embouts avant

des rails sur la collerette verticale.

REMARQUE :

pour retirer les rails, appuyez sur le bouton de dégagement du

loquet situé au milieu de l'embout et dégagez les rails un par un.

3

Glissez le système dans le rack.

4

Si les deux supports d'expédition du stabilisateur de châssis

(en option) sont présents, retirez-les du rack.

REMARQUE :

avant de transporter des systèmes déjà installés dans le rack,

assurez-vous que les deux supports d'expédition du stabilisateur de châssis

(en option) sont en place.

La page charge ...

Dell PowerEdge C6105 Le manuel du propriétaire

Dell PowerEdge C6105 Le manuel du propriétaire

dans d''autres langues

Documents connexes