HearthPro SP5718 Mode d'emploi

Model#: SP5718

USER MANUAL

Keep this manual for future reference

QUESTIONS, PROBLEMS, OR MISSING PARTS?

Please Contact Customer Service Before Returning to Store

Please carefully check the unit and make sure there is no damage when you open the carton.

[email protected]

+1-844-455-4621

www.soupro.com

• GENERAL INFORMATION

Package Contents

Safety Instructions

Maximum Load Warning

Warranty

• ASSEMBLY INSTRUCTIONS

Preparation

Assembly

• FIREBOX OPERATIONS

FCC/IC Information

Safety Information

Operating Instructions

Care And Maintenance

Troubleshooting

Table of Contents

Package Contents

Fireplace Mantel

SP5718

Firebox

SP1816-HE-FGPB

Remote Control

2

General InformatIon

2

3

4

5

7

17

18

19

20

21

Maximum Load Warning

WARNING: This unit is not a television stand. Top of unit is not a shelf. Do not place a television or any item on

this unit. Failure to secure the unit correctly or placing items on the unit may result in instability causing tip over

resulting in death or serious injury.

Safety Instructions

Please read and understand this entire manual before attempting to assemble, operate or install the product.

IMPORTANT NOTICE

When using electrical appliances, basic precautions should always be followed to reduce the risk of re, electric shock

and injury to persons, including the following:

WARNING: Place this unit in a location that avoids direct sunlight and high temperatures.

WARNING: Plastic bags, nails, etc. should be kept out of reach of children.

WARNING: This appliance is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. Keep

combustible material, such as furniture, pillows, bedding, papers, clothes and curtains, at least 3 feet from the front

of the heater and keep them away from the side and rear.

WARNING: Extreme caution is necessary when any heater is used by or near children or individuals with

disabilities and whenever the replace is left operating and unattended.

WARNING: DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar covering.

Do not route cord under furniture or appliances. Arrange cord away from traffic areas and where it will not be

tripped over.

WARNING: DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause

an electric shock or re, or damage the appliance.

WARNING: This appliance has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline,

paint or ammable vapors or liquids are used or stored. This replace should not be used as a drying rack for

clothing. Christmas stockings or decorations should not be hung in the area of it.

3

General InformatIon

Warranty

1-YEAR LIMITED WARRANTY

Soupro Limited Inc. (hereinafter referred to collectively as “the Company”) warrants that your new KOMODO Electric

Fireplace is free from manufacturing and materials defects for a period of one (1) year from date of purchase. Subject to the

following conditions and limitations:

1. The electric fireplace must be installed and operated at all times in accordance with the installation

and operating instructions furnished with the product. Any unauthorized repair, alteration, willful abuse,

accident, or misuse of the product shall nullify this warranty.

2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was

made through an authorized supplier of the Company.

3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or

workmanship – provided that such part(s) have been subjected to normal conditions of use and service –

after said defect is conrmed by the Company’s inspection. All replacement parts or products will be new,

remanufactured, or refurbished.

4. The Company may, at its discretion, require that any defective part(s) be returned in exchange for the

replacement part(s).

5. The Company may, at its discretion, fully discharge all obligations with respect to this warranty by

refunding the wholesale price of the defective part(s).

6. This warranty does not cover the LED light bar included with the electric replace.

7. Any installation, labor, construction, transportation, or other related costs/expenses arising from defective

part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor shall the

Company assume responsibility for the same.

8. The owner/user assumes all other risks – if any – including but not limited to the risk of any direct, indirect

or consequential loss or damage arising out of the use, or inability to use the product, except as provided

by law.

9. All other warranties – express or implied – with respect to the unit, its components and accessories, or

any obligations/liabilities on the part of the Company are hereby expressly excluded.

10. The Company neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities

with respect to the sale of the unit.

11. The warranties as outlined within this document do not apply to non-accessories used in conjunction with

the installation of this product.

12. This warranty gives you specic legal rights, and you may also have other rights which vary from state to

state.

This warranty is void if:

(a) The replace is subjected to prolonged periods of dampness or condensation.

(b) Any unauthorized alteration, willful abuse, accident, or misuse of the product.

(c) You do not have the original purchase receipt.

IF WARRANTY SERVICE IS NEEDED

Please Contact Customer Service

Make sure you have the following information ready:

• Warranty

• Sales Receipt

• Product Model/Serial Number

• Date of Purchase

• Location of Purchase

4

General InformatIon

[email protected]

+1-844-455-4621

www.soupro.com

Preparation

IMPORTANT INFORMATION

1. Before you begin, locate the instructions and hardware. Be sure you have all of the parts and can identify

them.

2. To avoid scratching the finish, assemble the product on a soft, non-abrasive surface such as carpet or

cardboard.

3. Assembly of this product may require more than one person.

Tools Required

5

ASSEMBLY INSTRUCTIONS

Number of spare hardware is indicated in ( ).

Hardware Identication

Use the Touch-up Pen to cover surface scratches.

WARNING: The included plastic wall anchors (OO) are intended for use with solid wall applications only (tile and

concrete). DO NOT USE WITH DRYWALL OR OTHER HOLLOW WALL APPLICATIONS.

Philips Screwdriver Hand Drill Hex Key

HH x 1

Touch-up Pen

KK x 2 LL x 2+(1) MM x 2+(1)

CC x 20+(2)BB x 58+(3)

EE x 29

GG x 1

DD x 7+(1)

OO x 2NN x 4+(2)

II x 8 + (1)

Parts List

Preparation

6

ASSEMBLY INSTRUCTIONS

x 1

x 2

x 1

A

C

F

G

H

B

D

E

x 1

x 2

x 1

A

P

O

K

N

L

J

M

I

G

E

D

B

C

F

H

I

J

K

L

M

N

O

P

Assembly

1.

7

ASSEMBLY INSTRUCTIONS

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

EE x 8BB x 8

H

I

G

F

E

D

BB

EE

BB

EE

BB

2.

Assembly

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

8

ASSEMBLY INSTRUCTIONS

4.

3.

N

J

M

L

N

BB

EE

BB

EE

BB

EE x 10BB x 10

EE x 3BB x 3

Assembly

9

ASSEMBLY INSTRUCTIONS

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

5.

6.

II x 2

M

L

N

F

J

G

N

B

C

BB

II

DD

II x 2DD x 3BB x 2

Assembly

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

10

ASSEMBLY INSTRUCTIONS

8.

7.

B

CC

DD

BB

DD x 4CC x 2

BB x 2

D

Assembly

11

ASSEMBLY INSTRUCTIONS

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

9.

10.

E

H

I

BB

BB x 6

BB x 2

Assembly

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

12

ASSEMBLY INSTRUCTIONS

11.

12.

K

O

M

N

L

BB

II

BB

BB x 7

II x 4

Assembly

13

ASSEMBLY INSTRUCTIONS

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

13.

14.

CC

BB

CC

BB

CC

CC x 2BB x 6

CC x 4BB x 4

A

Assembly

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

14

ASSEMBLY INSTRUCTIONS

15.

16.

P

CC

CC x 12

Assembly

15

ASSEMBLY INSTRUCTIONS

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

17.

FCC / IC Information

Firebox Model

Assembly

Do not fully tighten screws during assembly. Only tighten when all parts are installed in place.

WARNING:

•Ifinstallingthemantelondrywallorotherhollowwallapplications,thesafetymountingtape(KK)mustbe

fastenedtostuds,headers,orotherstructuralwallmembers.Theincludedplasticwallanchors(OO)are

intendedforusewithsolidwallapplicationsonly(tileorconcrete).

•DONOTUSEWITHDRYWALLOROTHERHOLLOWWALLAPPLICATIONS.

16

ASSEMBLY INSTRUCTIONS

LL x 2KK x 2 MM x 2 NN x 4 OO x 2

KK

NN

MM

OO

LL

ATTENTION:

• Find a location for the rebox that is protected from direct sunlight.

• Failure to read all instructions may result in a possible electric shock, re hazard and/or injury and will void

the warranty.

WARNING:

• If the information in this manual is not followed exactly, an electric shock or re may result causing property

damage, personal injury or loss of life.

• Do not store or use gasoline or other ammable vapors or liquids in the vicinity of this appliance.

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

The equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on. The user is encouraged to try and correct the interference by one or more of the following measures:

(a) Reorient or relocate the receiving antenna

(b) Increase the separation between the equipment and the receiver

(c) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

(d) Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(a) This device may not cause harmful interference, and

(b) This device must accept any interference received, including interference that may cause undesired operation.

Modications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES-003.

FCC / IC Information

Firebox Model

17

FIREBOX OPERATIONS

SP1816-HE-FGPB

Safety Information

Use this rebox only as described in the manual. Any other use is NOT recommended by the manufacturer and may cause

re, electric shock or injury to persons.

CAUTION:

• If possible, ALWAYS unplug this rebox when not in use.

• DO NOT operate any rebox with a damaged cord or plug or after the heater malfunctions.

• DO NOT operate any rebox if it has been dropped or damaged in any manner. Disconnect power at service panel and have

rebox inspected by a reputable electrician before reusing.

• Any repairs to this unit should be carried out by appropriately qualied service personnel.

• Under no circumstances should this unit be modied. Parts having to be removed for servicing must be replaced prior to

operating this unit again.

• DO NOT use outdoors.

• This unit is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER place heater where it may

fall into a bathtub or other water container.

• To disconnect this unit, turn all controls to the OFF position, then remove plug from outlet.

• ONLY connect to properly grounded outlets.

• This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA C22.1

Canadian Electrical Code or, for USA installations, follow the National Electrical Code, ANSI/NFPA NO.70.

• To prevent a possible re, DO NOT block any air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a

bed, where opening may become blocked.

• ALWAYS plug this unit directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap

(outlet/power strip).

• This heater includes an automatic protection system that will shut off the unit to prevent overheating. If the unit is at risk of

overheating, the front panel will display "E1" and a thermal cut out will shut off the heater to prevent damage or risk of re.

• DO NOT slide rebox on top of wood to avoid scratching wood surface.

• DO NOT place any objects on top of rebox and top air intake vents as this will cause the unit to overheat and can cause a

re.

ELECTRICAL CONNECTION:

• A 15-amp, 120-volt, 60 Hz circuit with a properly grounded

outlet is required. Preferably, the fireplace will be on

a dedicated circuit as other appliances on the same

circuit may cause the circuit breaker to trip or the fuse

to blow when the heater is in operation. The unit comes

standard with 6-ft. three-wire cord, exiting from the rear

of the fireplace. DO NOT exceed the current rating of

the current tap. ALWAYS plug this unit directly into a wall

outlet/receptacle. NEVER use with an extension cord or

relocatable power tap (outlet/power strip).

• This rebox is for use on 120 volts. The cord has a plug as

shown below. See illustration for grounding instruction. An

adapter as shown at C is available for connecting three-

blade grounding type plugs to two-slot receptacles. The

green grounding lug extending from the adapter must

be connected to a permanent ground such as a properly

grounded outlet box. The adapter should not be used if a

three-slot grounded receptacle is available.

Grounding Pin

Grounding Means

Adapter

A

C

B

D

Metal Screw

Cover of

Grounding Box

ELECTRICAL SPECIFICATIONS

Voltage:

Amps:

Watts:

120 VAC, 60 Hz

11.7 Amps

1400 Watts

18

FIREBOX OPERATIONS

Flame Brightness Mode

• The Flame Brightness Mode sets the ame brightness.

• Use UP arrow button or DOWN arrow button to scroll

through the flame brightness settings: F0 (no flame),

F1, F2, F3, F4, F5 (brightest).

• Use UP arrow button to increase the setting of the

selected function.

• Use DOWN arrow button to decrease the setting of the

selected function.

Activate Child Lock

• When the unit is ON, hold the POWER button for 10

seconds to activate the Child Lock function. "E3" will be

displayed and a "beep" will sound 3 times to indicate the

Child Lock function is activated. Then, all function keys are

locked. When pressing any button, "E3" will be displayed

to indicate the Child Lock function has been activated.

Deactivate Child Lock

• To deactivate the Child Lock function, hold the POWER

button for 10 seconds. Then, all functions keys are

unlocked.

• Press the POWER button to turn ON or OFF the unit.

• When the unit is in ON mode, the power icon indicator

light will be shown green.

• When the unit is in OFF mode, the power icon indicator

light will be shown red. When power OFF, unit will be

stopped, if heater is working before power OFF the

unit, fan will have 20 seconds delay to ensure heat will

not be trapped inside the unit.

• Press the MODE button to cycle through the different

functions. Each time the MODE button is pressed, the

mode will enter the next function – Temperature, Timer

or Flame Brightness.

Temperature Mode

• The Temperature Mode controls the heater’s thermostat

setting.

• Press UP arrow button or DOWN arrow button to scroll

through temperature settings: 59°F – 86°F (15°C –

30°C), ON, OF (OFF).

• Hold the MODE button for 3 seconds; this toggles the

temperature unit between °C or °F.

• When the ambient temperature is higher than the set

temperature, heater will turn off automatically.

Timer Mode

• The Timer Mode sets the fireplace to automatically

shutoff.

• Press UP arrow button or DOWN arrow button to adjust

the timer setting from 0 hour (OFF) to 9 hours with 0.5

hour intervals.

Operating Instructions

Power Button

Each time the rebox is plugged in, a 5-second fan and

heater will turn on for internal check program.

The unit has a memory function with last settings for

heating level and ame brightness effect, unless the main

power to the unit has been interrupted.

Mode Button

Up Arrow Button

Down Arrow Button

Child Lock

This function is only available if using the control panel.

Child Lock function is only available if using the control

panel.

19

FIREBOX OPERATIONS

Care And Maintenance

NOTE: When the heater is not in use, it should be stored in a dry location, away from possible damage. The

power cord should be stored properly to avoid contact with hot or sharp objects.

REPLACING THE REMOTE CONTROL BATTERY:

When the remote control stops operating or its range seems reduced, it is time to replace the batteries.

NOTE: The batteries should be removed if the product is to be left unused for a long time.

CAUTION:

Non-rechargeable battery is not to be recharged. Exhausted battery is to be removed from the product:

1. The battery compartment is located on the back end of the remote control.

2. Press the small tab inward as you slide the battery door open and remove the old battery.

3. Insert a new CR2025 lithium battery (not included), ensuring the polarities of the battery match the inside of

the battery compartment.

4. Re-insert the battery door.

WARNING: Make sure the power is turned off before proceeding. Any electrical repairs or rewiring of this unit

should be carried out by a licensed electrician in accordance with national and local codes.

If repairing or replacing an electrical component or wiring, the original wire routing, color coding and securing

locations must be followed.

WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to

reduce the risk of re, electrical shock and injury to persons.

WARNING: Do not use this replace if any part of it has been under water. Immediately call a qualied service

technician to inspect the replace and replace any part of the electrical system.

WARNING: Disconnect the power before attempting any maintenance or cleaning to reduce the risk of re,

electrical shock or personal injury.

WARNING: During any service of this appliance, the power to the unit must be turned off. First turn the main

power switch to the "OFF" position. Then remove the electrical plug from the wall outlet.

WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN

1. Swallowing may lead to serious injury in as little as 2 hours or death, due to

chemical burns and potential perforation of the oesophagus.

2. If you suspect your child has swallowed of inserted a button battery, immediately

seek urgent medical assistance.

3. Examine devices and make sure the battery compartment is correctly secured,

e.g that the screw or other mechanical fastener is tightened. Do not use if

compartment is not secure.

4. Dispose of used buttom batteries immediately and safety. Flat batteries can still be

dangerous.

5. Tell others about the risk associated with button batteries and how to keep their

children safe.

Troubleshooting

Problems

1. No power, logs do not

glow.

2. "E1" is displayed on

control panel.

3. "E2" is displayed on

control panel.

4. "E3" is displayed on

control panel.

5. Fan motor continues

to blow after unit is

powered off.

6. Power cord gets warm

to the touch.

1. The unit does not have

power.

2. The overheat protection

device has been

engaged.

3. The ambient temperature

sensor is broken or not

working correctly.

4. Child Lock function is

activated.

5. Normal operation.

6. Normal operation.

Possible Causes

1. Check that unit is plugged into a standard

120 volt outlet. Then make sure power is set

at "ON" position.

2. Unplug unit, wait 5-10 minutes, then the

sensor will reset itself. Plug the unit back

in and turn on the heater. If the problem

persists, call customer service.

3. Unplug unit, wait 5-10 minutes, then the

sensor will reset itself. Plug the unit back

in and turn on the heater. If the problem

persists, call customer service.

4. To inactivate the Child Lock function, hold

the POWER button for 10 seconds.

5. This is a standard feature; the blower runs

for an additional 20 seconds to ensure heat

will not be trapped inside the unit.

6. This is normal for a heater appliance as it

requires more current to operate. Check the

connections of the appliance cord and the

outlet. Make sure the plug fits tightly into

the outlet. During use, check the plug and

outlet frequently to determine if it is HOT;

if so, discontinue use of the appliance and

consult with a qualied electrician to check

or change the overheating outlet(s).

Solutions

CLEANING INFORMATION:

• Make sure the unit is turned off, unplugged and the heating elements of heater are cool whenever you are cleaning the

heater.

• Clean the metal trim using a water-dampened, soft, and clean cloth. DO NOT use brass polish or household cleaners as

these products will damage the metal trim.

• The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life and

require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and air intake/output vents is

recommended.

20

FIREBOX OPERATIONS

La page charge ...

HearthPro SP5718 Mode d'emploi

HearthPro SP5718 Mode d'emploi

dans d''autres langues

Autres documents