Simplicity 1696528-01 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur

Ce manuel convient également à

Not for
Reproduction
Operator’s Manual
Manual del operador
Manuel de l’utilisateur
Part No.: 80014884USCN
Revision: -
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA
All rights reserved.
en
es
fr
Not for
Reproduction
2
Manual Contents:
Operator Safety ..................................................................2
Safety System Tests ..........................................................7
Features and Controls .......................................................8
Operation ............................................................................9
Maintenance .................................................................... 12
Troubleshooting .............................................................. 16
The images in this document are representative, and are
meant to complement the instructional copy they accompany.
Your unit may vary from the images displayed. LEFT and
RIGHT are as seen from the operator’s position.
NOTE: Please refer to the Customer Contact Guide and
Setup Instructions for additional information.
The safety alert symbol indicates a potential personal
injury hazard. A signal word (DANGER, WARNING, or
CAUTION) is used with the alert symbol to designate a
degree or level of hazard seriousness. A safety symbol may
be used to represent the type of hazard. The signal word
NOTICE is used to address practices not related to personal
injury.
DANGER indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazard which, if not avoided, could
result in death or serious injury.
CAUTION indicates a hazard which, if not avoided, could
result in minor or moderate injury.
NOTICE indicates an action that could result in damage to
the product.
Operator Safety
Safety Alert Symbol and Signal Words
Hazard Symbol Charts
Snowthrower Hazard Symbols
Symbol Meaning Symbol Meaning
Safety informa-
tion about haz-
ards that can
result in personal
injury.
Read and under-
stand the opera-
tor’s manual
before operating
or servicing the
unit.
Amputation
hazard - rotating
impeller.
Remove the key
before perform-
ing service.
Amputation
hazard - rotating
impeller.
Amputation
hazard - rotating
auger.
Amputation haz-
ard - do not touch
moving parts.
Thrown objects
hazard.
Fire hazard. Explosion haz-
ard.
Shock hazard. Toxic fume haz-
ard.
Hot surface haz-
ard.
Ear protection
recommended
for extended use.
Keep a safe dis-
tance.
Wear safety
glasses.
Keep children
away.
Kickback hazard.
Not for
Reproduction
3
English
en
General Safety Warnings
DANGER
Keep hands, feet, and clothing away from rotating parts.
Rotating parts can contact or entangle hands, feet, hair,
clothing, or accessories.
Failure to observe these safety instructions will result in
traumatic amputation or severe laceration.
Whenever cleaning, repairing, or inspecting the
snowthrower, make sure the engine is OFF, spark
plug wire is disconnected, and all moving parts have
stopped.
Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
Never operate the snowthrower without proper guards,
and other safety devices in place and working.
Never leave the snowthrower unattended while engine
is running. Always disengage the auger and traction
controls, stop engine, and remove keys.
Keep all loose clothing away from the front of the
snowthrower and auger. Scarves, mittens, dangling
drawstrings, loose clothes, and pants can quickly
become caught in the rotating device and amputation
will occur. Tie up long hair and remove jewelry.
Run the machine a few minutes after discharging snow
to prevent freeze-up of the collector/impeller.
Disengage power to the collector/impeller when
snowthrower is transported or not in use.
DANGER
The discharge chute contains a rotating impeller to throw
snow. Never clear or unclog the discharge chute with your
hands. Fingers can quickly become caught in the impeller.
Always use a clean-out tool.
Failure to observe these safety instructions will result in
traumatic amputation or severe laceration.
WARNING
U.S.A. Models: Certain components in this prod-
uct and its related accessories contain chemicals
known to the state of California to cause cancer, birth
defects, or other reproductive harm. Wash hands
after handling.
WARNING
U.S.A. Models: The engine exhaust from this product
contains chemicals known to the State of California
to cause cancer, birth defects, or other reproductive
harm.
Regional Warnings
WARNING
Hand contact with the rotating impeller inside the
discharge chute is the most common cause of injury
associated with snowthrowers.
This snowthrower is capable of amputating hands
and feet, and throwing objects. Read and observe all
the safety instructions in this manual. Failure to do so
could result in death or serious injury.
WARNING
Read, understand, and follow all the instructions on the
snowthrower and in the operator’s manual before operating
this unit.
Failure to observe the safety instructions in this manual
could result in death or serious injury.
Be thoroughly familiar with the controls and the proper
use of the snowthrower.
Make sure you are properly trained before operating
the snowthrower.
Know how to stop the unit and disengage the controls
quickly.
Never allow anyone to operate the snowthrower with-
out proper instruction.
Always follow the instructions in the operator’s manual,
if the snowthrower will be stored for an extended peri-
od.
Maintain or replace safety and instruction labels as
necessary.
Never attempt to make major repairs on the
snowthrower unless you have been properly trained.
Improper servicing of the snowthrower can result in
hazardous operation, equipment damage, and voiding
of the product warranty.
Not for
Reproduction
4
WARNING
Engines give off carbon monoxide, an odorless, colorless,
poison gas. Breathing carbon monoxide can cause nau-
sea, fainting, or death.
Start and run the engine outdoors.
Do not run the engine in an enclosed area, even if
doors and windows are open.
WARNING
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
unit and the operating activity. Never assume that children
will remain where you last saw them.
Keep children out of the area during operation.
Children are often attracted to the equipment. Be
mindful of all persons present.
Be alert and turn the unit off if children enter the area.
Never allow children to operate the unit.
Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure vision.
Children may be present.
WARNING
Fuel and its vapors are extremely flammable and explo-
sive. Always handle fuel with extreme care.
Failure to observe these safety instructions can cause a
fire or explosion which will result in severe burns or death.
When Adding Fuel
Turn off engine and let cool at least 2 minutes before
removing the fuel cap and adding fuel.
Fill fuel tank outdoors or in a well ventilated area.
Do not overfill the fuel tank. To allow for the expansion
of gasoline, do not fill above the bottom of the fuel tank
neck.
Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
Check fuel lines, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
Use an approved fuel container.
If fuel spills, wait until it evaporates before starting
engine.
When Starting Engine
Ensure that spark plug, muffler, fuel cap, and air clean-
er (if equipped) are in place and secured.
Do not crank the engine with the spark plug removed.
If fuel is spilled, do not attempt to start the engine, but
move the snowthrower away from the area of the spill,
and avoid creating any source of ignition, until the fuel
vapors have dissipated.
Do not over-prime the engine. Follow the engine start-
ing instructions in this manual.
If the engine floods, set choke (if equipped) to OPEN/
RUN position, move throttle (if equipped) to FAST
position and crank until engine starts.
When Operating Equipment
Do not tip the snowthrower at an angle which causes
the fuel to spill.
Do not choke the carburetor to stop the engine.
Never run the engine with the air cleaner assembly (if
equipped) or the air filter (if equipped) removed.
When Changing Oil
If you drain the oil from the top oil fill tube, the fuel tank
must be empty or fuel can leak out and result in a fire
or explosion.
When Transporting Equipment
Transport with fuel tank EMPTY, or with fuel shut-off
valve OFF.
When Storing Gasoline or Equipment With Fuel in
Tank
Store away from furnaces, stoves, water heaters, or
other appliances that have pilot light or other ignition
source because they can ignite fuel vapors.
WARNING
Objects can be picked up by the auger and thrown from
the chute. Never discharge snow toward bystanders
or allow anyone in front of the snowthrower. Failure to
observe these safety instructions will result in death or
serious injury.
Always wear safety glasses or eye shields during oper-
ation, and while performing an adjustment or repair.
Always be aware of the direction the snow is being
thrown. Nearby pedestrians, pets, or property may be
harmed by objects being thrown.
Be aware of your environment while operating the
snowthrower. Don’t run over items such as gravel,
doormats, newspapers, toys, and rocks hidden under
snow, as they can all be thrown from the chute or jam
in the auger.
Use extreme caution when operating on or crossing
gravel drives, walks, or roads.
Adjust the collector housing height to clear gravel or
crushed rock surface.
Never operate the snowthrower near glass enclo-
sures, automobiles, window wells, drop-offs, and the
like without proper adjustment of the discharge chute
angle.
Familiarize yourself with the area in which you plan to
operate the snowthrower. Mark off boundaries of walk-
ways and driveways.
Not for
Reproduction
5
English
en
WARNING
Safe operation of the snowthrower requires the proper care
and maintenance of the engine.
Disengage all clutches and shift into neutral before
starting the engine.
Let the engine adjust to outdoor temperatures before
starting to clear snow.
Use a grounded three-wire plug for all snowthrowers
equipped with electric drive motors or electric starting
motors.
WARNING
Starting the engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
If there is natural gas or LP gas leakage in the area, do
not start the engine.
Do not use pressurize starting fluids because their
vapors are flammable.
WARNING
Running the engine produces heat. Engine parts, espe-
cially the muffler, become extremely hot.
Failure to observe these safety instructions could result in
severe thermal burns on contact.
Never touch a hot engine or muffler. Allow muffler,
engine cylinder, and fins to cool before touching.
Remove debris from muffler area and cylinder area.
Install and maintain in working order a spark arrester
before using equipment on forest-covered, grass-cov-
ered, or brush-covered unimproved land.
U.S.A. Models: It is a violation of California Public
Resource Code Section 4442 to use or operate the
engine on any forest-covered, brush-covered, or
grass-covered land unless the exhaust system is
equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other
states or federal jurisdictions may have similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
WARNING
This snowthrower must be properly maintained to ensure
safe operation and performance. Failure to observe the
safety instructions in this manual could result in death or
serious injury.
When performing any maintenance or repairs on the
snowthrower, shut OFF the engine, disconnect spark
plug wire, and keep the wire away from the plug to pre-
vent someone from accidently starting the engine.
Check shear bolts and other hardware at frequent
intervals for proper tightness.
Keep nuts and bolts tight and keep snowthrower in
good condition.
Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if they
are not functioning properly.
Components are subject to wear, damage, and dete-
rioration. Frequently check components and replace
with recommended parts, when necessary.
Check control operation frequently. Adjust and service
as required.
Use only factory authorized replacement parts, or like,
parts when making repairs.
Always comply with factory specifications on all set-
tings and adjustments.
Use only factory authorized, or like, attachments and
accessories such as wheel weights, counterweights,
or cabs.
Never attempt to make any adjustments while the
engine is running (except when specifically recom-
mended by the factory).
Not for
Reproduction
6
WARNING
This snowthrower is only as safe as the operator. If it is
misused, or not properly maintained, it can be dangerous.
Remember you are responsible for your safety and those
around you.
Keep the area of operation clear of all persons, par-
ticularly small children and pets.
Thoroughly inspect the area where the snowthrower
will be used and remove all doormats, sleds, boards,
wires, and other foreign objects.
Do not operate the snowthrower without wearing ade-
quate winter clothing.
Wear footwear that will improve footing on slippery sur-
faces.
Use caution to avoid slipping or falling especially when
operating the snowthrower in reverse.
Never operate the snowthrower without good visibility
or light. Always be sure of your footing, and keep a firm
hold on the handles.
Do not clear snow across the face of slopes. Use
extreme caution when changing direction on slopes.
Do not attempt to clear steep slopes.
Do not overload the machine capacity by attempting to
clear snow too quickly.
Never operate the snowthrower at high transport
speeds on slippery surfaces. Look behind the
snowthrower and use care when operating in reverse.
Do not use the snowthrower on surfaces above ground
level such as roofs of residences, garages, porches, or
other such structures or buildings.
Operators should evaluate their ability to operate the
snowthrower safely enough to protect themselves and
others from injury.
The snowthrower is intended to remove snow only. Do
not use the snowthrower for any other purpose.
Do not carry passengers.
After striking a foreign object, shut OFF the engine,
disconnect the cord on electric motors, thoroughly
inspect the snowthrower for any damage, and repair
the damage before restarting and operating the
snowthrower.
If the snowthrower vibrates abnormally, shut OFF the
engine. Vibration is generally a warning of trouble. See
an authorized dealer if necessary for repairs.
For models equipped with electric starting motors, dis-
connect the power cord after the engine starts.
WARNING
Damaged or ungrounded power cords could cause electric
shock.
Electric shock could cause severe burns or death.
When Using the Electric Starter
The power cord must be properly grounded at all
times.
Use only a three-conductor power cord properly
grounded to the power source.
If the power cord is damaged, it must be replaced by a
qualified person to avoid a hazard.
WARNING
Rapid retraction of the starter cord (kickback) will pull your
hand and arm toward the engine faster than you can let go.
Broken bones, fractures, bruises, or sprains could result.
When starting the engine
Pull the starter cord slowly until resistance is felt and
then pull rapidly to avoid kickback.
Not for
Reproduction
7
English
en
Before operating your unit, read the safety decals. Compare
Figure 1 with the table below. The cautions and warnings are
for your safety. To avoid a personal injury or damage to the
unit, understand and follow all the safety decals.
Safety Decals
WARNING
If any safety decals become worn or damaged, and
cannot be read, order replacement decals from your
local dealer.
1
A Chute Danger Decal
(P/N 1737865)
B Auger Danger Decal
(P/N 1737866)
C Engine Warning Decal
(P/N 278297)
Safety System Tests
Safety System Test (units with Free
Hand control)
WARNING
Amputation hazard
This snowthrower is equipped with several mechanical
safety systems designed to keep the operator safe while
using the unit. Check the operation of these systems regu-
larly using the safety system tests listed. If the unit fails to
operate as described, DO NOT operate it. See your autho-
rized dealer for service immediately.
Test 1 - Auger/Impeller Control
With the engine running:
Press down on the auger control lever. (The auger/
impeller should rotate)
Release the auger control lever. (The auger/impeller
must stop within 5 seconds)
Test 2 - Traction Drive Control
With the engine running and speed control in 1st gear:
Press down on the traction control lever. (The unit
should move forward)
Release the traction control lever. (The unit must stop)
Test 3 - Free Hand Control
With the engine running:
Engage the auger and traction control levers, then
release the auger control lever. (Both controls should
remain engaged)
Next, release the traction control lever. (Both controls
must release)
Not for
Reproduction
8
Features and Controls
Engine Features and Controls
Snowthrower Features and Controls
For engine features and controls, please refer to the engine
operator’s manual.
Compare Figure 2 with the table below.
E
E
H
I
J
K
F
G
2
A
1
R1
R2
2
3
Speed Select Lever - Allows
the operator to use one of
five forward and two reverse
speeds. To shift, move speed
select lever to desired position.
NOTICE: Do not move speed
select lever while Traction
Control is engaged. This
may result in severe damage
to the drive system.
B
Auger Control Lever - Used
to engage and disengage the
auger and impeller. To engage,
push down. To disengage,
release.
C
Chute Rotation Switch - Used
to rotate the discharge chute to
the left or right.
D Chute Deflector Control
Lever (if equipped) - Used to
control the angle of the deflec-
tor (up or down).
E Chute Deflector Switch (if
equipped) - Used to control
the angle of the deflector (up or
down).
F Traction Control Lever - Used
to propel snowthrower for-
ward or reverse. Push down to
engage, release to disengage.
See also, “Free-Hand Control”.
G
Free Hand™ Control - After
engaging the traction control
(left hand) and auger control
(right hand), allows the opera-
tor to release the auger control
lever to use other controls.
H
Easy Turn™ Traction Control
- When engaged, allows the
operator to release one drive
wheel, but allows the other
wheel to continue driving for
easy turning.
I
Grip Warmer Switch - Used
to warm the hand grips (high,
off, low).
J
-
Clean-Out Tool - Used to
remove snow and debris from
the discharge chute and the
auger housing.
K
-
Skid Shoes - Used to adjust
the ground clearance of the
auger housing.
Not for
Reproduction
9
English
en
Operation
Before Operating the Snowthrower
WARNING
Read the operator’s manual before operating the
machine. This machine can be dangerous if used
carelessly.
Never operate the snowthrower without all guards,
covers, and shields in place.
Stop the engine whenever leaving the operating posi-
tion.
Remove the key before unclogging the impeller hous-
ing or discharge chute, and before making repairs or
adjustments.
When leaving the machine, remove the key.
To reduce the risk of fire, keep the machine clean and
free from spilled fuel, oil, and debris.
On electric start models, disconnect the extension cord
before operating.
Be sure to check the engine oil level before starting the
engine. See the engine operator’s manual for oil recom-
mendations.
1. Start the engine. Please refer to the engine operator’s
manual for engine information.
2. Use the chute rotation switch (C, Figure 2) to set the
direction of the discharge chute.
3. Use the chute deflector control lever (D, if equipped) or
chute deflector switch (E, if equipped) to raise and lower
the deflector. Raise the deflector to throw snow further.
4. Use the speed select lever (A) to select the forward or
reverse drive speed. Use lower speeds when clearing
wet, heavy snow. Use higher speeds for light snow or
transporting.
NOTE: Always set engine speed to FAST (full throttle).
5. Fully press the auger control lever (B) to engage the
auger. Releasing the auger control lever will stop the
auger, unless the Free Hand control (G) is activated.
6. Fully press and hold the traction control/Free Hand lever
(F, G) to engage the traction drive and begin moving the
snowthrower. To stop, release the lever.
NOTE: Always release the traction control lever before
changing speeds.
7. When both the auger and traction control levers are
pressed, the Free Hand control is activated. This allows
you to release the auger control to use other controls.
The auger will continue to rotate until the traction control/
Free Hand control is released.
8. If desired, use the grip warmer switch (I) to turn on the
heated hand grips.
Operating the Snowthrower
DANGER
Amputation hazard
The discharge chute contains a rotating impeller to
throw snow. Fingers can quickly become caught in
the impeller. Never clear or unclog the discharge
chute with your hands. Always use a clean-out tool.
Failure to observe these safety instructions will result
in traumatic amputation or severe laceration.
Hand contact with the rotating impeller inside the dis-
charge chute is the most common cause of injury associ-
ated with snowthrowers. Never use your hands to clean out
the discharge chute.
To safely clear a clogged discharge chute, follow
these instructions:
1. Shut OFF the engine.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean-out tool, not your hands.
WARNING
Thrown objects hazard
This machine is capable of throwing objects that could
injure bystanders, or cause damage to buildings.
Be sure the operating area is clear of bystanders. Never
direct the discharge toward anyone, or toward buildings or
cars.
DANGER
Toxic fume hazard
Engines give off carbon monoxide, an odorless, col-
orless, poison gas.
Breathing carbon monoxide can cause nausea, faint-
ing, or death.
Start and run the engine outdoors.
Do not run the engine in an enclosed area, even if
doors and windows are open.
Not for
Reproduction
10
For easy turning when using the snowthrower, squeeze the
Easy Turn traction control lever (Figure 3).
NOTE: Some models feature Easy Turn traction control for
one wheel only, while other models feature it for both wheels.
NOTE: Easy Turn traction control will be more difficult to acti-
vate under a heavy load. Activate the lever before beginning
a turn.
Move the chute deflector control lever (A, Figure 5) forward
or backward to raise and lower the deflector (B). Raise the
deflector to throw snow further.
While the engine is running, press either side of the chute
deflector switch (C, Figure 5) to raise and lower the deflector
(B). Raise the deflector to throw snow further.
While the engine is running, press either side of the chute
rotation switch (A, Figure 6) to rotate the discharge chute (B)
left or right.
Engaging the Easy Turn traction control lever releases one
of the traction wheels, but allows the other wheel to continue
driving. Releasing the Easy Turn traction control lever auto-
matically engages both drive wheels for full traction (Figure
4).
Easy Turn™ Traction Control (if
equipped)
Chute Deflector Adjustment
Chute Rotation Adjustment
3
C
5
6
4
1. Release the auger control lever (B, Figure 2).
2. Release the traction control lever (H).
3. Stop the engine. Please refer to the engine operator’s
manual for engine instructions.
Stopping the Snowthrower
Chute Deflector Control Lever (if equipped)
Chute Deflector Switch (if equipped)
Not for
Reproduction
11
English
en
Wheels equipped with a traction lock pin (A, Figure 7) can be
completely released by removing the pin and installing it in
the outer axle hole. Reverse this process to engage the drive
wheel.
Wheel Release - Lock Pins (if equipped)
7
Please refer to the engine operator’s manual for information
about filling the fuel tank, and for fuel recommendations.
Filling the Fuel Tank
A clean-out tool (A, Figure 8) is provided with the unit.
Clearing a Clogged Discharge Chute
DANGER
Amputation hazard
The discharge chute contains a rotating impeller to
throw snow. Fingers can quickly become caught in
the impeller. Never clear or unclog the discharge
chute with your hands. Always use a clean-out tool.
Failure to observe these safety instructions will result
in traumatic amputation or severe laceration.
Hand contact with the rotating impeller inside the dis-
charge chute is the most common cause of injury associ-
ated with snowthrowers. Never use your hands to clean out
the discharge chute.
To safely clear a clogged discharge chute, follow
these instructions:
1. Shut OFF the engine.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean-out tool, not your hands.
8
Skid Shoe Height Adjustment
DANGER
Amputation hazard
The discharge chute contains a rotating impeller to throw
snow. Fingers can quickly become caught and traumatic
amputation or severe laceration will result. Hand contact
with the rotating impeller inside the discharge chute is the
most common cause of injury associated with snowthrow-
ers.
Turn the engine OFF, wait for all moving parts to stop, and
remove the engine key before performing any maintenance
or repairs.
WARNING
Thrown objects hazard
Objects such as gravel, rocks, or other debris, if struck
by the impeller, may be thrown with sufficient force to
cause personal injury, property damage, or damage to the
snowthrower.
Be sure to set the skid shoes at the proper height to main-
tain ground clearance for the type of surface being cleared.
This snowthrower is equipped with two height adjust skids,
secured to the outside of the auger housing. These elevate
the front of the snowthrower.
When removing snow from a hard surface area such as a
paved driveway or walk, adjust the skids up to bring the front
of the snowthrower down.
When removing snow from gravel-covered or uneven sur-
faces, raise the front of the snowthrower by moving the skids
down. This will help to prevent rocks and other debris from
being picked up and thrown by the augers.
1. Determine how much clearance you want between the
scraper bar at the bottom of the auger housing and the
ground. If clearing a gravel surface, enough ground clear-
ance is needed to prevent the unit from picking up rocks.
2. Place a block equal to the desired ground clearance
under the scraper bar.
Not for
Reproduction
12
9
If the unit will be stored for 30 days or more at the end of the
season, the following steps are recommended to prepare it
for storage. Always refer to the operator’s manual for impor-
tant details if the unit is to be stored for an extended period.
Please refer to the engine operator’s manual for engine stor-
age information.
NOTE: Fuel must be removed or treated to prevent gum
deposits from forming in the tank, filter, hose, and carburetor
during storage.
Off-Season Storage
WARNING
Fire and explosion hazard
Gasoline is highly flammable and its vapors are explosive.
Fumes may travel to a distant ignition source and an explo-
sion and/or fire may result.
Handle gasoline carefully. Never store the unit, with fuel in
the tank, indoors or in a poorly ventilated enclosure where
fuel fumes could reach an open flame, spark, pilot light,
such as a furnace, water heater, or clothes dryer.
Thoroughly clean the unit.
Lubricate all lubrication points (see Maintenance sec-
tion).
Make sure all nuts, bolts, and screws are securely fas-
tened. Inspect all visible moving parts for damage, break-
age, and wear. Replace if necessary.
Touch up all rusted or chipped paint surfaces; sand light-
ly before painting.
Cover the bare metal parts of the snowthrower housing
auger, and the impeller with rust preventative.
Maintenance
Maintenance Schedule
Before Each Use
• Check engine oil level
• Perform Safety System Test
Every 8 Hours or Daily
• Check engine oil level
Every 25 Hours or Annually
• Lubricate control lever linkages
• Lubricate the auger assembly
• Lubricate the discharge chute rotation gear and
deflector
• Lubricate the hex shaft with 5w-30 synthetic motor oil,
and chains with grease
Every 50 Hours or Annually
• Check muffler and spark arrester (if equipped)
• Check tire pressure
For engine maintenance schedules and procedures, please
refer to the engine operator’s manual.
Lubricate the unit at the locations show in Figure 10. Where
an oil can is pictured, lubricate with engine oil. Where a
grease gun is pictured, lubricate with lithium grease.
Engine Maintenance
Control Lever Linkage Lubrication
WARNING
Amputation hazard
It is critical for safe operation of the unit that the controls
disengage when released. Under no circumstances should
the unit be used if the controls do not function properly.
See Safety Systems Tests to confirm correct operation.
3. Loosen the skid shoe mounting nuts (A, Figure 9) and
push the skid shoe (B) down until it touches the ground.
Re-tighten mounting nuts.
4. Set the skid shoe on the other side at the same height.
If possible, store your unit indoors and cover it to give
protection from dust and dirt.
If the machine must be stored outdoors, cover with a
heavy tarpaulin.
To Return to Service:
Fill the fuel tank with a fresh fuel.
Make sure all fasteners are tight.
Make sure all guards, shields, and covers are in place.
Not for
Reproduction
13
English
en
The auger gear box is lubricated at the factory and should
not require additional lubrication. However, if lubricant has
leaked out or the auger gear box has been serviced, addi-
tional lubricant may be required.
To check the auger gear box grease level, remove the filler
plug (A, Figure 11). Using a piece of wire as a dipstick, check
to confirm the presence of grease in the gearbox. If grease is
visible, do not add. If grease is not visible, add the required
lubricant (Lubriplate GR132 Grease or equivalent). Gearbox
lubricant capacity is 3-1/4 ounces (92 grams).
Lubricate Auger Gear Box
Auger Assembly Lubrication
10
11
Using a grease gun, lubricate the auger shaft fittings (B,
Figure 11). Refer to the Maintenance Schedule. Each time a
shear bolt or pin (C) is replaced, the auger shaft MUST be
greased.
For storage or when replacing shear bolts or pins, remove
the shear bolts or pins (C), lubricate the shaft fittings (B),
and rotate the augers several times to distribute the grease.
Reinstall the shear bolts or pins when complete.
Lubricate the chute rotation gear (Figure 12) with grease, and
the deflector mechanism with automotive type oil. Refer to
the Maintenance Schedule.
Where an oil can is pictured, lubricate with engine oil. Where
a grease gun is pictured, lubricate with lithium grease.
NOTICE
Do not allow grease or oil to contact the rubber friction wheel
or the disc drive plate. If the disc drive plate or friction wheel
come in contact with grease or oil damage to rubber friction
wheel will result.
If grease or oil comes into contact with the disc drive plate or
friction wheel, make sure to clean plate and wheel thoroughly
with an alcohol based solvent.
1. Position speed select lever in the first forward gear.
2. Drain fuel to an approved container.
Lubricate Auger Shaft Fittings
Discharge Chute and Deflector
Lubrication
Hex Shaft and Chain Lubrication (if
equipped)
12
Not for
Reproduction
14
IMPORTANT – After adjusting the pulley, perform the
following drive system tests:
With the engine OFF and the gear selector in first
Forward gear position:
a. Engage the traction drive control. The snowthrower
should not roll forward when pushed.
b. Release the traction drive control. The snowthrower
should roll forward when pushed.
With engine RUNNING and the gear selector in first
Forward gear position:
a. Engage the traction drive control. The snowthrower
should roll forward without pushing.
b. Release the traction drive control. The snowthrower
should stop immediately.
With engine RUNNING and the gear selector in the first
Reverse gear position:
a. Engage the traction drive control. The snowthrower
should roll rearward without pulling.
b. Release the traction drive control. The snowthrower
should stop immediately.
If the snowthrower does not pass these tests, re-adjust
the pulley and test again. Contact an authorized service
dealer for assistance, if needed.
3. Stand the snowthrower up on the auger housing end.
NOTE: When the crankcase is filled with oil, do not leave
the snowthrower standing up on the auger housing for an
extended period of time.
4. Remove the bottom panel.
5. Lubricate the chains (A, Figure 13) with grease.
6. Wipe the hex shaft (B) with 5W30 synthetic motor oil,
before storage and at the beginning of each season.
7. Install the bottom panel.
13
WARNING
Fire and explosion hazard
Gasoline is highly flammable and its vapors are explosive.
Drain gasoline outdoors, away from fire and other ignition
sources. Wipe up any spills immediately. Do NOT allow
open flame, smoking, or matches in the area.
Traction Cable Adjustment
The traction cable may stretch slightly after repeated usage
during the first season of operation. If the cable is stretched,
it could prevent the drive system from engaging in Forward
or Reverse gears. To adjust the cable, follow the procedure
below or contact an authorized service dealer for assistance.
1. Position snowthrower on a level garage or driveway
surface.
2. Place gear selector in the first Forward gear position.
3. Loosen nut at the traction cable pulley.
4. Start the engine.
5. Gradually slide the pulley rearward in the bracket slot
until the snowthrower just begins to move. Then slide
the pulley forward slightly until the snowthrower stops.
Tighten the nut to secure the pulley at this position.
NOTE: If the snowthrower does not move, even with the
pulley in the full rearward position, then leave the pulley at
the full rearward position and tighten the nut to secure it.
6. Shut down the engine.
The traction drive belt is under constant spring tension and
does not require any adjustment. If the traction drive belt is
slipping, see your authorized dealer.
If the Easy Turn cable has stretched, the gears will not dis-
engage when the control lever is activated. Adjust the cable
using the following procedure.
1. Turn the engine off and remove the key.
2. Loosen the jam nut (A, Figure 14).
3. Turn the adjustment nut (B) to lengthen or shorten the
cable. The cable should be tightened until all slack is
removed from the lever. However, it must not engage the
Easy Turn without depressing the control lever.
4. Tighten the jam nut (A).
If the speed control rod requires adjustment, see an autho-
rized dealer.
Traction Drive Belt Adjustment
Easy Turn™ Cable Adjustment
Speed Control Rod Adjustment
Not for
Reproduction
English
en
15
15
The augers are secured to the auger shaft with special shear
pins that are designed to break if an object becomes lodged
in the auger housing. Use of a harder grade shear pin will
reduce the protection provided by the shear pin.
Under most circumstances, if the auger strikes an object
which could cause damage to the unit, the shear pin will
break. This protects the gear box and other parts from dam-
age.
NOTICE
Do not replace the shear pins with anything other than the
correct grade replacement shear pin. Use of bolts, screws, or
harder grade shear pins can result in equipment damage.
Auger Shear Pin Replacement
WARNING
Amputation hazard
The discharge chute contains a rotating impeller to throw
snow. Fingers can quickly become caught and traumatic
amputation or severe laceration will result. Hand contact
with the rotating impeller inside the discharge chute is the
most common cause of injury associated with snowthrow-
ers.
Turn the engine OFF, wait for all moving parts to stop, and
remove the engine key before performing any maintenance
or repairs.
The shear pins and clips (A and B, Figure 16) are located on
the auger shaft. Replace a broken shear pin as follows.
1. Tap out the broken shear pin with a pin punch.
2. Install a new shear pin and cotter pin. Bend the ends of
the cotter pin down.
1. With the auger control lever released, the hook (A, Figure
15) should barely touch the lever (B) without raising it.
There can be a maximum of 1/32” (0.8 mm) clearance.
2. To adjust, loosen the nut (C) by holding the adjustment
screw (D) and turning the nut. Then, turn the turnbuckle
and hold the adjustment screw (D). The adjustment
screw is a phillips screw and the head can be held or
turned by inserting a screwdriver through the spring.
3. Hold the screw and tighten the nut to secure.
4. To ensure that the auger does not engage unless the
control is fully depressed, please perform the Safety
System Test. The auger must stop within 5 seconds
of the control being released.
Auger Cable Adjustment
WARNING
Amputation hazard
Over-tightening the auger cable may cause the auger drive
to engage without depressing the auger drive control.
Follow the adjustment procedure to ensure the cable is not
over-tightened.
14
Not for
Reproduction
16
16
16
Tire pressure should be checked periodically. Recommended
tire pressure varies by tire manufacturer. A good rule of
thumb is to inflate the tire up to, but not exceeding, the “Max
Inflation” stamped on the side-wall of the tire.
Checking Tire Pressure
Not for
Reproduction
17
English
en
Troubleshooting
Troubleshooting Chart
Perform the inspection or repair as indicated in the Troubleshooting Chart.
Problem Look for Remedy
Auger does not stop within 5 seconds
after right control lever is released.
Free Hand control (if equipped) is
ACTIVE.
Release both auger control and Free
Hand control (if equipped) to stop
auger.
Auger drive belt out of adjustment. See authorized dealer.
Auger belt guide out of adjustment. See authorized dealer.
Discharge chute or deflector does not
work (electric).
Electrical failure. See authorized dealer.
Discharge chute or deflector does not
work
(remote-manual).
Discharge chute or deflector out of
adjustment or needs lubrication.
Adjust and/or lubricate control linkage.
Drive fails to move snowthrower at slow
speeds.
Traction control out of adjustment. See authorized dealer.
Engine fails to start. Key is in OFF position. Set key to ON position.
Failure to prime a cold engine. Press primer button twice and restart.
Fuel shut-off valve, if equipped, is in
CLOSED position.
Turn valve to OPEN position.
Out of fuel. Fill fuel tank.
Choke turned to OPEN/RUN with cold
engine.
Turn choke to CLOSED/START, set
throttle to FAST.
Engine flooded. Move the choke to OPEN/RUN posi-
tion, move throttle to FAST position,
and crank until the engine starts.
No spark. See authorized dealer.
Engine starts hard or runs poorly. Water in fuel, or old fuel. Drain tank. (Dispose of fuel at an autho-
rized hazardous waste facility.) Fill with
fresh fuel.
Spark plug faulty, fouled, or gapped
improperly.
See authorized dealer.
Fuel cap vent is blocked. Clear vent.
Excessive vibration. Loose parts or damaged impeller. Stop engine immediately. Tighten all
hardware. If vibration continues, have
the unit serviced by an authorized
dealer.
Snowthrower does not stop when trac-
tion control lever is released.
Traction control out of adjustment. See authorized dealer.
Scraper bar does not clean hard sur-
face.
Skid shoes and scraper bar improperly
adjusted.
Raise or lower skid shoes and scraper
bar.
Unit fails to propel itself. Drive belt loose or damaged. Replace drive belt. See authorized
dealer.
Incorrect adjustment of traction drive
cable.
See authorized dealer.
Worn or damaged friction disc. Replace friction disc. See authorized
dealer.
Not for
Reproduction
18
Problem Look for Remedy
Unit fails to discharge snow. Auger drive belt loose or damaged. See authorized dealer.
Auger control cable not adjusted cor-
rectly.
Adjust auger control cable. Refer to
Maintenance section of this manual.
Broken shear pin or shear bolt. Replace shear pin or bolt. Refer to
Maintenance section of this manual, or
see an authorized dealer.
Discharge chute clogged. Stop engine immediately. Always use
the clean-out tool to clear a clogged
discharge chute, not your hands. Clean
discharge chute and inside of auger
housing. Refer to Discharge Chute
Warning in the Operator Safety section.
Foreign object lodged in auger. Stop engine immediately. Always use
the clean-out tool to clear a clogged
chute, not your hands. Remove object
from auger. Refer to WARNINGS in the
Operator Safety section.
Not for
Reproduction
2
Español
es
Contenido del manual:
Seguridad del operador ....................................................2
Pruebas del sistema de seguridad ..................................7
Características y controles ...............................................8
Operación ............................................................................9
Mantenimiento ................................................................. 12
Solución de problemas .................................................. 16
Las imágenes en este documento son representativas y su propó-
sito es complementar la copia de instrucciones que acompañan. Su
unidad puede verse diferente a las imágenes mostradas. Se hace
referencia a IZQUIERDA y DERECHA desde la posición del opera-
dor.
NOTA: Consulte la Guía de contacto del cliente y las Instrucciones
de configuración para obtener información adicional.
El símbolo de alerta de seguridad indica un posible peligro
de lesiones corporales. Se utiliza una palabra de señalización
(PELIGRO, ADVERTENCIA o PRECAUCIÓN) junto con el símbolo
de alerta para designar un grado o nivel de gravedad del peligro.
Se puede utilizar un símbolo de seguridad para representar el tipo
de peligro. La palabra de señalización AVISO se utiliza para desig-
nar prácticas no relacionadas con lesiones corporales.
PELIGRO indica un peligro que, si no se evita, provocará la
muerte o una lesión grave.
ADVERTENCIA indica un peligro que, si no se evita, podría
provocar la muerte o una lesión grave.
PRECAUCIÓN indica un peligro que, si no se evita, podría pro-
vocar una lesión menor o moderada.
AVISO indica una situación que podría provocar daños en el pro-
ducto.
Seguridad del operador
Símbolo de alerta de seguridad y pala-
bras de señalización
Tabla de símbolos de peligro
Símbolos de peligro del soplador de nieve
Símbolo Significado Símbolo Significado
Información de
seguridad acerca
de los peligros que
pueden provocar
lesiones corpora-
les.
Lea y compren-
da el manual del
operador antes de
operar o realizar
mantenimiento a la
unidad.
Peligro de ampu-
tación: propulsor
giratorio.
Retire la llave
antes de realizar
reparaciones.
Peligro de ampu-
tación: propulsor
giratorio.
Peligro de ampu-
tación: barrena
giratoria.
Peligro de amputa-
ción: no toque las
piezas móviles.
Peligro de objetos
expulsados.
Peligro de incen-
dio.
Peligro de explo-
sión.
Peligro de descar-
ga.
Peligro de gases
tóxicos.
Peligro de superfi-
cie caliente.
Se recomienda
protección auditiva
de uso prolongado.
Mantenga una dis-
tancia prudente.
Use anteojos de
seguridad.
Mantenga a los
niños alejados.
Peligro de contra-
golpe.
Not for
Reproduction
3
Advertencias generales de seguridad
PELIGRO
Mantenga alejados las manos, los pies y la ropa de las piezas
giratorias. Las piezas giratorias pueden tocar o enredar las
manos, pies, cabello, ropa o accesorios.
Si no sigue estas instrucciones de seguridad, podrá sufrir ampu-
taciones traumáticas o quemaduras graves.
Siempre que limpie, repare o inspeccione el soplador de
nieve, asegúrese de que el motor está APAGADO, que el
cable de la bujía de encendido está desconectado y que
todas las piezas móviles están detenidas.
No coloque las manos o pies cerca o debajo de piezas gira-
torias. Manténgase lejos en todo momento de la apertura de
descarga.
Nunca ponga en funcionamiento el soplador de nieve sin
que las protecciones u otros dispositivos de seguridad apro-
piados estén colocados en su lugar y funcionen correcta-
mente.
Nunca deje el soplador de nieve sin supervisión mientras el
motor esté funcionando. Siempre desactive los controles de
tracción y de la barrena, apague el motor y retire las llaves.
Mantenga toda ropa suelta lejos del frente del soplador de
nieve y la barrena. Bufandas, mitones, cordones colgantes,
ropa y pantalones anchos pueden atascarse rápidamente
en el dispositivo giratorio, provocando una amputación.
Recójase el pelo largo y quítese las joyas.
Opere la máquina algunos minutos después de lanzar nieve
para evitar el congelamiento del colector y del propulsor.
Desconecte la electricidad del colector y del propulsor cuan-
do transporte o no utilice el soplador de nieve.
PELIGRO
El conducto de descarga contiene un propulsor giratorio que
arroja la nieve. No limpie ni desatasque el conducto de descarga
con las manos. Puede pillarse los dedos rápidamente en el pro-
pulsor. Utilice siempre una herramienta de limpieza.
Si no sigue estas instrucciones de seguridad, podrá sufrir ampu-
taciones traumáticas o quemaduras graves.
ADVERTENCIA
Modelos para EE. UU.: Algunos componentes de este pro-
ducto y sus accesorios relacionados contienen sustancias
químicas que el estado de California sabe que causan cán-
cer, defectos de nacimiento u otros daños reproductivos.
Lávese las manos después de manipular estos elementos.
ADVERTENCIA
Modelos para EE. UU.: El escape del motor de este pro-
ducto contiene sustancias químicas que el estado de
California sabe que causan cáncer, defectos de nacimiento
u otros daños reproductivos.
Advertencias regionales
ADVERTENCIA
El contacto de las manos con el propulsor giratorio dentro
del conducto de descarga es la causa más común de lesio-
nes asociadas a los sopladores de nieve.
Este soplador de nieve es capaz de amputar manos y pies y
arrojar objetos. Lea y comprenda todas las instrucciones de
seguridad que aparecen en este manual. Si no lo hace, es
posible que pueda sufrir lesiones graves e incluso la muerte.
ADVERTENCIA
Lea, comprenda y siga todas las instrucciones que aparecen en
el soplador de nieve y en el manual del operador antes de poner
en funcionamiento esta unidad.
Si no lee detenidamente las instrucciones de seguridad que apa-
recen en este manual, podrá sufrir lesiones graves o incluso la
muerte.
Esté completamente familiarizado con los controles y el uso
correcto del soplador de nieve.
Asegúrese de que tiene la capacitación necesaria antes de
poner en funcionamiento el soplador de nieve.
Sepa cómo parar la unidad y desactivar los controles rápi-
damente.
Nunca deje que alguien sin instrucción apropiada opere el
soplador de nieve.
Siga siempre las instrucciones que aparecen en el manual
del operador si el soplador de nieve se va a almacenar
durante un periodo de tiempo largo.
Mantenga o reemplace las etiquetas de instrucciones y de
seguridad cuando sea necesario.
Nunca intente realizar reparaciones mayores en este sopla-
dor de nieve a no ser que tenga la capacitación necesaria.
Si se llevan a cabo tareas de reparación incorrectas en el
soplador de nieve, puede ocasionar un funcionamiento peli-
groso, daños en el equipo y la anulación de la garantía del
producto.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Simplicity 1696528-01 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur
Ce manuel convient également à