SATO PV4 Manuel utilisateur

SATO
Marque
SATO
Modèle
PV4
Catégorie
Imprimantes d'étiquettes
Taper
Manuel utilisateur
User’s Manual
PV4
BARCODE PRINTER
Rev. 1.00
Ver. 1.00
- 2 -
PV4
Introduction
The PV4 is a 4-inch thermal mobile label printer which simultaneously connects with
Bluetooth and WLAN. Ideal for smart mobility labelling due to its compact, lightweight design
with an easy-to-open peeler and LCD.
※ The main features of the printer are as follows
1. 4-inch Mobile Label Printer
2. Maximum 127 mm/s (5ips) printing speed.
3. Compact and light design 158 x 186 x 82 mm (6.23 × 7.33 × 3.23 inch) (W x D x H)
4. Peeler
5. Paper guide (paper width : 50 ~ 112 mm)
6. Wireless connectivity (Bluetooth V5.0(Classic / LE), Wireless LAN 802.11 a/b/g/n)
It is advisable to read the contents of this manual carefully before using the printer for the first
time.
※ Use only authorized supplies that can be trusted!
We are not responsible for quality and service for damage caused by the use of
unauthorized supplies (or recycled ones).
Ver. 1.00
- 3 -
PV4
Safety Information
Warning
Warnings must be heeded carefully in order to prevent serious
physical harm.
Caution
Cautions must be heeded in order to prevent minor injuries,
equipment damage, or data loss.
Symbol Information
Ver. 1.00
- 4 -
PV4
Table of Contents
1. Content Confirmation ........................................................................................................ 12
2. Product Part Names ........................................................................................................... 12
3. Installation & Usage ........................................................................................................... 14
3-1 Battery Installation ........................................................................................................... 14
3-2 Battery Charging ............................................................................................................. 14
3-2-1 Using AC/DC Adaptor .......................................................................................... 14
3-2-2 Using 1CH Battery Charger (Optional) ................................................................ 15
3-2-3 Using 4CH Battery Charger (Optional) ................................................................ 15
3-3 Paper Installation ............................................................................................................ 17
3-4 Using Peeler .................................................................................................................... 18
3-5 Using Belt Strap .............................................................................................................. 19
3-6 Using Fan-Fold Paper ..................................................................................................... 20
3-7 Using Control Panel ........................................................................................................ 21
3-9 Recommended Papers ................................................................................................... 22
4. Self-Test .............................................................................................................................. 23
5. LCD Menu............................................................................................................................ 25
6-1 Bluetooth, Wireless LAN Connection .............................................................................. 28
6-2 Interface Cable Connection ............................................................................................. 29
6-3 Fixed Interface Cable Connection ................................................................................... 30
7. Printer Cleaning .................................................................................................................. 31
8. Appendix ............................................................................................................................. 32
8-1 Specifications .................................................................................................................. 32
8-2 Label Types ..................................................................................................................... 33
Ver. 1.00
- 5 -
PV4
Manual Information
This user’s manual contains basic information for product usage as well as for emergency
measures that may be required.
※ The following separate manuals provide more detailed content on various technological
issues and areas.
1. Software Manual
This manual provides information for development.
Please refer to each manual for more information.
• Windows Driver Manual
• OPOS Driver Manual
• Linux CUPS Driver Manual
• MAC CUPS Driver Manual
• Virtual Com for USB Driver Manual
• iOS Label Printer SDK Manual
• Android Label Printer SDK Manual
• Windows CE SDK Manual
• Windows Label SDK Manual
• Linux Label SDK Manual
• Xamarin SDK Manual
• Unified Label Utility-II Manual
• Net Configuration Tool Manual
• mPrint Server Manual
2. Bluetooth, Wireless LAN Connection Manual
• Bluetooth Connection Manual
- This manual describes how to connect terminals (PDAs, PCs, etc.) with Bluetooth
functionality.
• Wireless LAN Connection Manual
- This manual describes how to connect wireless LAN in infrastructure or Soft AP
3. Commands Manual
This manual provides information on the protocol and functions of the control commands that
can be used with this product.
4. Code Pages Manual
The following pages show the character code tables. To find the character corresponding to a
hexadecimal number, count across the top of the table for the left digit and count down the left
column of the table for the right digit.
5. SLCS(Programing) Manual
In this chapter, the basic concept of SLCS and some information necessary for the programmer
to use SLCS will be explained. Please read this part before starting programming for efficient
and ease of use of SATO BARCODE PRINTERS.
6. Paper Specification
This manual contains paper specifications needed to use barcode printer.
Ver. 1.00
- 6 -
PV4
Safety Precautions
In using the present equipment, please keep the following safety regulations in order to
prevent any hazard or material damage.
WARNING
Violating following instructions can cause serious injury or death.
Do not bend the cable by force or leave it under any
heavy object.
• A damaged cable can cause a fire.
Do not plug in or unplug with wet hands.
• You could be electrocuted.
Keep the plastic bag out of children’s reach.
• If not, a child may put the bag on there head.
Do not pull the cable to unplug.
• This can damage the cable, could cause fire or a breakdown of
the printer.
You must use only the supplied adaptor.
• It is dangerous to use other adaptors.
Do not plug several products into one multi-outlet.
• This can provoke over-heating and a fire.
• If the plug is wet, or dirty, wipe it before using.
• If the plug does not fit perfectly in the outlet, do not plug in.
• Be sure to use only standardized multi-outlets.
PROHIBIT
ED
PROHIBIT
ED
PROHIBIT
ED
PROHIBIT
ED
PROHIBIT
ED
ONLY SUPPLIED ADAPTOR
PROHIBIT
ED
Ver. 1.00
- 7 -
PV4
CAUTION
Violating following instructions can cause an injury or damage the appliance
.
Do not use the printer when it is out of order. This
can cause a fire or an electrocution.
• Switch off and unplug the printer before calling your supplier.
Do not let water or other foreign objects in the
printer.
• If this happens, switch off and unplug the printer before
calling your dealer.
Use only approved accessories and do not try to
disassemble, repair or remodel it for yourself.
• Call your dealer when you need these services.
• Do not touch the blade of the paper tear bar (or auto cutter).
Install the printer on a stable surface.
• If the printer falls down, it can be broken and you can hurt
yourself.
Keep the desiccant out of children’s reach.
• If not, they may eat it.
If you observe a strange smoke, odour or noise
from the printer, unplug it before taking following
measures.
• Switch off the printer and unplug the set from the mains.
• After the disappearance of the smoke, call your dealer to
repair it.
TO UNPLUG
PROHIBIT
ED
DISASSEMBLING
PROHIBITED
PROHIBIT
ED
PROHIBIT
ED
TO UNPLUG
PRINTER
PRINTER
PRINTER
PRINTER
DEALER
PRINTER
Ver. 1.00
- 8 -
PV4
Battery Safety Warning
Please be sure to read this guide prior to use.
Warning
1. If the battery is not charged after the charging time, stop charging and contact the supplier.
2. Store and use the battery where it will not come into contact with liquid (water, salt water,
etc.). There may be a risk of overheating, rupturing or igniting.
3. Avoid exposing the battery to high temperatures over 50℃ and do not store or use it in a
place with high temperature and humidity. There may be a risk of overheating, rupturing or
igniting. In addition, it may reduce the performance and life of the battery. There is a risk of
explosion, especially when the battery is placed by a fire or stored near a heating device
(e.g., heater, etc).
4. Do not put the battery in a microwave oven or high-pressure cooker (pressure cooker, etc.).
There may be a risk of overheating, rupturing or igniting.
5. Do not use or leave the battery exposed to direct sunlight or high temperatures such as in
a car. It may reduce battery performance and life, or there may be a risk of overheating,
rupturing or igniting.
6. The usage temperature range of the battery is as follows. If used outside of this range,
battery performance and life may be reduced, or there may be a risk of overheating,
rupturing or igniting.
- Charging: 0 to 40°C (32 to 104°F)
- Using: -15 to 50°C (5 to 122°F)
- Long-term storage (over 30 days): -15 to 40°C (5 to 104°F)
7. Be sure to only use an adaptor or charger approved by us to charge the battery. Use of
any other adaptor or charger may reduce battery performance and life, or cause a risk of
overheating, rupturing or igniting.
8. Do not use the (+) and (-) terminals of the battery reversely. Failure to use the equipment
may result in an abnormal chemical reaction inside the battery, which may cause
overheating, rupturing or igniting.
9. Do not touch the (+) and (-) terminals of the battery with metal. Also, do not carry or store it
with metallic goods (necklaces, hair pins, coins, etc.). There may be a risk of overheating,
rupturing or igniting.
10. Do not use the battery in a place where static electricity can be generated. It may damage
the device, resulting in reduction of battery performance and life, or there may be a risk of
overheating, rupturing or igniting.
11. Avoid causing any strong impact to the battery or throwing it. The protective device inside
the battery may be damaged, which may reduce the battery performance and life, or there
may be a risk of overheating, rupturing or igniting.
Ver. 1.00
- 9 -
PV4
12. Do not disassemble or modify the battery. The battery contains safety and protection
devices to prevent danger. It may reduce battery performance and life due to damage, or
there may be a risk of overheating, rupturing or igniting.
13. If any leakage of the battery comes into contact with the eyes or skin, immediately rinse
with clean water such as tap water and consult a doctor immediately.
14. Keep the battery out of the reach of children and infants. If it is swallowed, consult a
doctor immediately.
15. The battery subjected to extremely low air pressure that may result in an explosion or the
leakage of flammable liquid or gas.
Recommendations
1. Do not charge for longer than the charging time described in this guide, as it may reduce
battery performance and duration.
2. If the battery is not expected to be used for a long time, remove it from the equipment and
keep in a place with low humidity.
3. Be sure to turn off the power of the equipment after use. Failure to do so may reduce the
performance and life of the battery.
4. Batteries that have not been used for a long time may fail to charge properly. Even if you
do not use the battery for a long time, charge it at least once every 6 months whilst storing
it.
5. If the (+) and (-) terminals of the battery are contaminated, wipe them with a dry cloth and
use in a clean condition. The contamination of battery may result in unstable contact with
the equipment and the power may be cut off or the battery may not be charged.
Disposal
1. When using, storing or charging the battery, if you detect any abnormality such as an odour,
overheating, discoloration, deformation, leakage, etc., please remove the battery from the
equipment or charger and dispose of it immediately.
2. When disposing of the battery, completely discharge it, cover the terminals with insulation
tape, and dispose of it at a designated location according to relevant laws and regulations
set by the government.
Ver. 1.00
- 10 -
PV4
Avertissements de sécurité pour la batterie
Assurer d’avoir bien lu le présent manuel avant d’utiliser le produit.
Avertissement
1. Si la batterie n'est pas chargée après le temps de charge, arrêtez la charge et contactez le
fournisseur.
2. Stockez et utilisez la batterie dans un endroit où elle n'entrera pas en contact avec un
liquide (eau, eau salée, etc.). Il peut y avoir un risque de surchauffe, de rupture ou
d'inflammation.
3. Évitez d'exposer la batterie à des températures élevées sur 50℃ et ne la stockez pas ou
ne l'utilisez pas dans un endroit où la température et l'humidité sont élevées. Il peut y avoir
un risque de surchauffe, de rupture ou d'inflammation. De plus, cela peut réduire les
performances et la durée de vie de la batterie. Il existe un risque d'explosion, notamment
lorsque la batterie est placée près d'un feu ou stockée à proximité d'un appareil de
chauffage (par exemple, un radiateur, etc.).
4. Ne placez pas la batterie dans un four à micro-ondes ou une cocotte-minute (autocuiseur,
etc.). Il peut y avoir un risque de surchauffe, de rupture ou d'inflammation.
5. N'utilisez pas ou ne laissez pas la batterie exposée à la lumière directe du soleil ou à des
températures élevées, comme dans une voiture. Cela peut réduire les performances et la
durée de vie de la batterie ou représenter un risque de surchauffe, de rupture ou
d'inflammation.
6. La plage de température d'utilisation de la batterie est la suivante. Une utilisation en dehors
de cette plage peut réduire les performances et la durée de vie de la batterie ou
représenter un risque de surchauffe, de rupture ou d'inflammation.
- Charge : 0 à 40°C (32 à 104°F)
- Utilisation : -15 à 50°C (5 à 122°F)
Stockage pour une période prolongée (plus de 30 jours) : -15 à 40°C (5 à 104°F)
7. Veillez à n'utiliser qu'un adaptateur ou un chargeur approuvé par notre entreprise pour
charger la batterie. L'utilisation de tout autre adaptateur ou chargeur peut réduire les
performances et la durée de vie de la batterie, ou entraîner un risque de surchauffe, de
rupture ou d'inflammation.
8. Respectez la polarité (+) et (-) de la batterie. Une mauvaise utilisation de l'équipement
peut entraîner une réaction chimique anormale à l'intérieur de la batterie, qui peut
provoquer une surchauffe, une rupture ou une inflammation.
9. Ne touchez pas les bornes (+) et (-) de la batterie avec du métal. De même, ne la
transportez pas et ne la stockez pas avec des objets métalliques (colliers, épingles à
cheveux, pièces de monnaie, etc.). Il peut y avoir un risque de surchauffe, de rupture ou
d'inflammation.
Ver. 1.00
- 11 -
PV4
10. N'utilisez pas la batterie dans un endroit où de l'électricité statique peut être générée.
Cela peut endommager le dispositif, et réduire les performances et la durée de vie de la
batterie ou représenter un risque de surchauffe, de rupture ou d'inflammation.
11. Évitez de causer un choc violent à la batterie ou de la jeter. Le dispositif de protection à
l'intérieur de la batterie peut être endommagé, ce qui peut réduire les performances et la
durée de vie de la batterie ou représenter un risque de surchauffe, de rupture ou
d'inflammation.
12. Ne démontez pas ou ne modifier pas la batterie. La batterie contient des dispositifs de
sécurité et de protection pour éviter tout danger. Cela peut réduire les performances et la
durée de vie de la batterie, en raison d’une détérioration de cette dernière, ou représenter
un risque de surchauffe, de rupture ou d'inflammation.
13. Si un produit qui a fui de la batterie entre en contact avec les yeux ou la peau, rincez
immédiatement à l'eau claire, par exemple à l'eau du robinet, et consultez immédiatement
un médecin.
14. Gardez la batterie hors de portée des enfants et des bébés. En cas d’ingestion, consultez
immédiatement un médecin.
15. La batterie est soumise à une pression d'air extrêmement basse qui peut entraîner une
explosion ou une fuite de liquide ou de gaz inflammable.
Recommandations
1. Ne rechargez pas plus longtemps que le temps de charge décrit dans ce guide, car cela
peut réduire les performances et la durée de vie de la batterie.
2. Si la batterie ne doit pas être utilisée pendant une longue période, retirez-la de l'appareil et
conservez-la dans un endroit peu humide.
3. Veillez à couper l'alimentation de l'équipement après utilisation. Ne pas observer cette
recommandation peut réduire les performances et la durée de vie de la batterie.
4. Les batteries qui n'ont pas été utilisées pendant une longue période peuvent ne pas se
recharger correctement. Même si vous n'utilisez pas la batterie pendant une période
prolongée, rechargez-la au moins une fois tous les 6 mois tout en la stockant.
5. Si les bornes (+) et (-) de la batterie sont contaminées, essuyez-les avec un chiffon sec et
utilisez-les dans un état propre. La contamination de la batterie peut entraîner un contact
instable avec l'équipement et l'alimentation peut être coupée ou la batterie peut ne pas se
charger.
Mise au rebut
1. Lorsque vous utilisez, stockez ou chargez la batterie, si vous détectez une anomalie telle
qu'une odeur, une surchauffe, une décoloration, une déformation, une fuite, etc., veuillez
retirer la batterie de l'appareil ou du chargeur et la mettre immédiatement au rebut.
2. Lorsque vous mettez la batterie au rebut, déchargez-la complètement, couvrez les bornes
avec du ruban isolant et jetez-la dans un endroit dédié conformément aux lois et
règlements en vigueur.
Ver. 1.00
- 12 -
PV4
1. Content Confirmation
The following items should all be contained in the printer package.
Contact the dealer from which the purchase was made if any item is damaged and/or missing.
※ Basic items
PV4
Battery Pack
Belt Strap
Download Guide
Installation Guide
Paper Disks
(for 12mm inner
diameter)
※ Optional items
AC/DC Adaptor
Power Cord
1CH Battery
Charger
4CH Battery
Charger
Serial Cable
USB Cable
Ver. 1.00
- 13 -
PV4
2. Product Part Names
• Front
• Rear
Power Connection
Battery
Hole for mounting belt strap
Cable Connection
Interface Cap
Paper Cover
Power Button
LCD
Paper Feed Button
Peeler
Menu Move Button
Menu Select Button
Outer Terminal Cover
Cover Open Button
Charge
Indication LED
Shoulder Strap Ring
Ver. 1.00
- 14 -
PV4
3. Installation & Usage
3-1 Battery Installation
1) Insert the battery in the bottom of the
printer, and ensure that you align the
battery hook properly.
2) Push the battery into the slot until you
hear it “click” in place.
NOTE
As the battery is partially changed at the time of
purchase, charge the battery prior to product
use. (Use the AC/DC adaptor or the optional
1CH/4CH battery charger.)
3-2 Battery Charging
3-2-1 Using AC/DC Adaptor
1) Turn off the printer power.
2) Connect the power cord ② to the
AC/DC adaptor ① and then connect AC
power.
3) Open the external interface cap in the
direction of ③.
4) Connect the AC/DC adaptor to the power
connector.
NOTE
Battery charging status descriptions are as follows.
LED
Charge Status
Charge Time
Red LED On
Charging
Within 6 hours
Green LED On
Fully Charged
Red LED Blinking
Error Replace
or Reinstall Battery
Caution
The printer may incur serious damage if the AC/DC adaptor provided by SATO
is not used. SATO is not legally liable for any such damages.
(The voltage and electrical current specifications of the printer and battery
charger must match.)
Warning
Turn off the power before charging the battery for the printer.
①
②
③
Ver. 1.00
- 15 -
PV4
3-2-2 Using 1CH Battery Charger (Optional)
1) Connect the power cord ② to the
battery charger ①.
2) Connect the battery charger ① to the
power connector of the cradle ③.
3) Plug the power cord ② into an electrical
outlet.
4) Insert the battery ④ into the cradle ③ a
snapping sound is heard.
Caution
- The printer may incur serious damage if you do not use the battery charger
provided by SATO when using a single battery charger.
SATO is not legally liable for any such damages.
- You must use the battery charger power supply provided by SATO to use the
single battery charger. (AC/DC adaptor is not available)
3-2-3 Using 4CH Battery Charger (Optional)
3-2-3-1 Connecting the cables
1) Connect the power cord to the Adaptor,
and Connect the Adaptor to the power
connector of the quad battery charger.
2) Plug the power cord into a power Outlet.
Input power is 100 ~ 240VAC, 50/60Hz,
1.0A.
3) When the power is applied, the yellow,
green and red LEDs are on for three
seconds and do the self-test.
Warning
Use only designated AC/DC Adaptor. (12VDC, 3A)
①
②
③
④
Ver. 1.00
- 16 -
PV4
3-2-3-2 Charging Battery
1) Insert the battery into the 4CH Battery
Charger as shown in the figure on the left.
2) Gently slide the battery until it reaches the
bottom of the charger.
3) Charging starts as soon as the battery is
completely inserted.
4) After charging, remove the battery from the
4CH Battery Charger.
NOTE
Battery charging status descriptions are as follows.
LED
Charge Status
Charge Time
Red LED On
Charging
Within 10 hours
Green LED Blinking
Over 80% Charged
Green LED On
Fully Charged
Red LED Blinking
Error Replace
or Reinstall Battery
Warning
- If the red lamp of the charger blinks, install the battery again.
- If the red lamp continues to blink after several attempts (4 ~ 5 times)
to install the battery, contact your local dealer.
- The charging time may vary depending on the type of the charger or
ambient temperature.
Ver. 1.00
- 17 -
PV4
3-3 Paper Installation
1) Press the Open button to open the paper
cover.
2) Insert the paper as shown.
(Remove the empty core.)
3) Align the paper as shown.
4) Pull out the paper as shown and close the
paper cover.
Ver. 1.00
- 18 -
PV4
NOTE
The specification of the paper inner diameter of
the standard paper disks are 19 mm (0.75 inch).
If you are using paper with a smaller inner
diameter, remove the paper disks as shown
below and replace it with the supplied 12 mm
(0.47 inch) paper disks.
3-4 Using Peeler
1) Insert the paper after open the peeler as
shown.
2) Pull out the paper after close the peeler
as shown.
NOTE
Enable the peeler setting when using the peeler.
Refer to “Sensor setting” of “5. LCD Menu” to enable
peeler setting.
Ver. 1.00
- 19 -
PV4
3-5 Using Belt Strap
1) Insert the belt strap screw into the belt
strap hole.
2) Use a coin to tighten the belt strap screw
as shown in the image.
3) Unfasten the belt strap Velcro.
4) Slide the belt strap over a belt.
5) Close the Velcro as shown in the image.
Belt Strap
Coin
Belt
Belt
Ver. 1.00
- 20 -
PV4
3-6 Using Fan-Fold Paper
1-1) After keeping the paper holder open
wide (as shown), hold the paper holder by
lifting right guide holder as shown in the
figure.
NOTE
Use only when you are using 105 mm (4.13 inch)
paper.
1-2) After keeping the paper holder wide (as
shown), hold the paper holder by lifting left
guide holder as shown in the figure.
NOTE
Use only when you are using 112 mm (4.41 inch)
paper.
1-3) After keeping the paper holder wide (as
shown), hold the paper holder by using the
latch as shown in the figure.
NOTE
Use only when you are using 54~110 mm
(2.13~3.94 inch) paper.
2) Separate the fan-fold cover by pushing as
shown in the figure.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

SATO PV4 Manuel utilisateur

SATO
Marque
SATO
Modèle
PV4
Catégorie
Imprimantes d'étiquettes
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents