JVC MX-GB6 Le manuel du propriétaire
- Catégorie
- Lecteurs de cassettes
- Taper
- Le manuel du propriétaire
Ce manuel convient également à
MX-GB6
—Consists of CA-MXGB6 and SP-MXGB6
MX-GB5
—Consists of CA-MXGB5 and SP-MXGB5
COMPACT COMPONENT SYSTEM
SYSTEME DE COMPOSANTS COMPACT
MX-GB6/MX-GB5 COMPACT COMPONENT SYSTEM
SAM
LVT1188-002B
[C]
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
SP-MXGB6 SP-MXGB6
SP-MXGB5 SP-MXGB5
CA-MXGB6
CA-MXGB5
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
—Composé du CA-MXGB6 et SP-MXGB6
—Composé du CA-MXGB5 et SP-MXGB5
MXGB6&5[C]_Cover.p65 04.1.18, 3:19 PM3
G-1
Warnings, Cautions and Others
Mises en garde, précautions et indications diverses
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas
ouvrir le coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
Caution –– STANDBY/ON switch!
Disconnect the mains plug to shut the power off completely.
The STANDBY/ON switch in any position does not
disconnect the mains line. The power can be remote control-
led.
Attention –– Commutateur STANDBY/ON!
Déconnecter la fiche de secteur pour couper complètement
le courant. Le commutateur STANDBY/ON ne coupe
jamais complètement la ligne de secteur, quelle que soit sa
position. Le courant peut être télécommandé.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
For U.S.A.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open
and interlock failed or defeated. Avoid direct exposure to
beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED INSIDE THE UNIT.
IMPORTANT POUR PRODUITS LASER
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N’ouvrez pas le couvercle supérieur. Il n’y a
aucune pièce réparable par l’utilisateur à l’intérieur de
l’appareil; confiez toute réparation à un personnel qualifié.
3. ATTENTION: Risque de radiations laser visible et invisible
quand l’appareil est ouvert et que le système de
verrouillage ne fonctionne pas ou a été mis hors service.
Évitez toute exposition directe au rayon.
4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE
PRÉCAUTION PLACÉE À L’INTERIEUR DE
L’APPAREIL.
MXGB6&5[C]_Safety.p65 04.1.18, 3:18 PM1
G-2
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS
LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND.
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS
NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME
SUR LE MATERIEL BROUILLEUR: “APPAREILS NUMERIQUES”,
NMB-003 EDICTEE PAR LE MINISTRE DES
COMMUNICATIONS.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1 Front:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by
the dimensions below.
3 Bottom:
Place on the level surface. Maintain an adequate air path
for ventilation by placing on a stand with a height of 10 cm
or more.
Attention: Aération correcte
Pour prévenir tout risque de décharge électrique ou d’incendie et
éviter toute détérioration, installez l’appareil de la manière suivante:
1 Avant:
Bien dégagé de tout objet.
2 Côtés/dessus/dessous:
Assurez-vous que rien ne bloque les espaces indiqués sur le
schéma ci-dessous.
3 Dessous:
Posez l’appareil sur une surface plane et horizontale. Veillez à
ce que sa ventilation correcte puisse se faire en le plaçant sur
un support d’au moins dix centimètres de hauteur.
Front view
Face
Side view
Côté
1 cm
(
7
/16 in.)
1 cm
(
7
/16 in.)
15 cm
(5
15
/16 in.)
15 cm
(5
15
/16 in.)
15 cm
(5
15
/16 in.)
15 cm
(5
15
/16 in.)
15 cm
(5
15
/16 in.)
10 cm
(3
15
/16 in.)
CA-MXGB6 CA-MXGB6
CA-MXGB5
CA-MXGB5
SP-MXGB6
SP-MXGB5
SP-MXGB6
SP-MXGB5
Cooling fan*
Ventilateur de refroidissement*
* About the cooling fan
A cooling fan is mounted on the rear panel of the unit to prevent abnormal temperature inside the unit, thus assuring normal operation of the
unit. The cooling fan automatically starts rotating to intake external cool air when the volume is increased up to more than a certain level.
* À propos du ventilateur de refroidissement
Un ventilateur de refroidissement se trouve sur le panneau arrière de l’appareil afin d’éviter la création d’une température anormale à l’intérieur
de l’appareil et permettre ainsi un fonctionnement normal de l’appareil. Le ventilateur de refroidissement commence à tourner et à aspirer de
l’air frais automatiquement quand le volume est augmenté au-dessus d’un certain niveau.
MXGB6&5[C]_Safety.p65 04.1.18, 3:18 PM2
1
English
Introduction
About This Manual
This manual is organized as follows:
• The manual mainly explains operations using the
buttons and controls on the unit. You can also use the
buttons on the remote control if they have the same or
similar names (or marks) as those on the unit.
If operation using the remote control is different from
that using the unit, it is then explained.
• Basic and common information that is the same for many
functions is grouped in one place, and is not repeated in
each procedure. For instance, we do not repeat the
information about turning on/off the unit, setting the
volume, changing the sound effects, and others, which are
explained in the section “Common Operations” on pages 9
to 11.
• The following marks are used in this manual:
Gives you warnings and cautions to prevent
damage or risk of fire/electric shock.
Also gives you information which is not good
for obtaining the best possible performance
from the unit.
Gives you information and hints you had better
know.
Precautions
Installation
• Do not grasp the control knobs when moving or carrying
the unit.
• Install in a place which is level, dry and neither too hot nor
too cold—between 5˚C and 35˚C.
• Install the unit in a location with adequate ventilation to
prevent internal heat built-up in the unit.
• Leave sufficient distance between the unit and the TV.
• Keep the speakers away from the TV to avoid interference
with TV.
DO NOT install the unit in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or vibration.
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to
obtain the best possible performance from your unit, and retain this manual
for future reference.
Power sources
• When unplugging from the wall outlet, always pull the
plug, not the AC power cord.
DO NOT handle the AC power cord with wet
hands.
Moisture condensation
Moisture may condense on the lens inside the unit in the
following cases:
• After starting heating in the room
• In a damp room
• If the unit is brought directly from a cold to a warm place
Should this occur, the unit may malfunction. In this case,
leave the unit turned on for a few hours until the moisture
evaporates, unplug the AC power cord, and then plug it in
again.
Others
• Should any metallic object or liquid fall into the unit,
unplug the unit and consult your dealer before operating
any further.
• If you are not going to operate the unit for an extended
period of time, unplug the AC power cord from the wall
outlet.
DO NOT disassemble the unit since there are no
user serviceable parts inside.
If anything goes wrong, unplug the AC power cord and
consult your dealer.
EN_MXGB6&5[C]_01-08.p65 04.1.21, 6:18 PM1
2
English
Contents
Location of the Buttons and Controls ....................... 3
Front Panel ................................................................. 3
Remote Control .......................................................... 5
Getting Started............................................................ 6
Unpacking .................................................................. 6
Putting the Batteries into the Remote Control ........... 6
Connecting Antennas ................................................. 6
Connecting Speakers .................................................. 7
Connecting Other Equipment ..................................... 8
Canceling the Display Demonstration ....................... 8
Common Operations .................................................. 9
Turning On or Off the Power ....................................... 9
Setting the Clock ........................................................ 9
Selecting the Sources ................................................... 9
Adjusting the Volume ............................................... 10
Reinforcing the Bass Sound ..................................... 10
Enjoying the Powerful Sound—RHYTHM AX ....... 10
Selecting the Sound Modes ...................................... 11
Turning On or Off the Key-touch Tone .................... 11
Listening to the Radio .............................................. 12
Tuning in to a Station—Auto Search ....................... 12
Presetting Stations .................................................... 12
Tuning in to a Preset Station .................................... 12
Playing Back CDs ..................................................... 13
Loading CDs ............................................................ 13
Playing Back CDs—All Disc and One Disc ............ 13
Basic CD Operations ................................................ 15
Changing the MP3 Playback Mode.......................... 17
Turning On or Off the Resume Play for MP3 Disc .. 17
Programming the Playing Order of the Tracks
—Program Play .................................................. 18
Playing at Random—Random Play ......................... 19
Repeating Tracks or CDs—Repeat Play .................. 19
Prohibiting Disc Ejection—Carrousel Lock ............ 19
Playing Back Tapes ................................................... 20
Playing Back a Tape ................................................. 20
Recording .................................................................. 21
Recording a Tape on Deck B .................................... 21
Dubbing Tapes .......................................................... 22
CD Synchronized Recording ..................................... 22
Using the Timers ....................................................... 23
Using Daily Timer .................................................... 23
Using Recording Timer ............................................ 24
Using Sleep Timer .................................................... 25
Timer Priority ........................................................... 25
Maintenance .............................................................. 26
Troubleshooting ........................................................ 27
Specifications ............................................................. 28
EN_MXGB6&5[C]_01-08.p65 04.1.21, 6:18 PM2
3
English
Location of the Buttons and Controls
Become familiar with the buttons and controls on your unit.
Front Panel
y
u
;
a
s
d
f
o
i
1
2
3
6
7
8
9
p
q
4
5
w
e
r
t
EN_MXGB6&5[C]_01-08.p65 04.1.21, 6:18 PM3
4
English
See pages in the parentheses for details.
Front Panel
1 STANDBY/ON button (9, 24, 25)
2 Standby lamp (9)
3 Carrousel
4 Display window
5 Remote sensor (5)
6 REC START/STOP button (21)
CD REC START button (22)
DUBBING button (22)
7 REC lamp (21, 22)
SOUND MODE lamp (11)
RHYTHM AX lamp (10)
8 REPEAT button (13, 15, 19)
PROGRAM (MP3 Resume on/off) button (17, 18)
RANDOM button (19)
9 SOUND MODE control (11)
RHYTHM AX control (10)
p AUX button (9)
FM/AM button (9, 12)
CD 6 (play/pause) button (9, 13 – 15, 18)
TAPE A 3 (play) button (9, 20, 22)
TAPE B 3 (play) button (9, 20, 22)
Pressing one of these buttons also turns on the unit.
q CLOCK/TIMER button (9, 23 – 25)
SET/DISPLAY button (9, 12, 18, 23 – 25)
CANCEL/DEMO button (8, 9, 18, 24, 25)
w PHONES jack (10)
e TUNING +/– buttons (12)
¡ / 1 (fast forward/fast rewind) buttons (15, 20)
r 7 (stop) button (13 – 15, 18 – 22)
BEEP button (11)
t Deck A cassette holder (20, 22)
Pressing the 0 (open/close) portion opens the holder.
y CD 0 (Carrousel open/close) button (13 – 15, 17 – 19)
Pressing this button also turns on the unit.
u DISC CHANGE button (13, 15)
i Disc number buttons (CD1, CD2, and CD3) (14, 15, 18,
19, 22)
Pressing one of these buttons also turns on the unit.
o CD READY lamps (CD1, CD2, and CD3) (14)
; SUBWOOFER LEVEL +/– control (10)
a VOLUME control (10)
s AUX jack (8)
d PRESET +/– buttons (12)
¢ / 4 (forward search/reverse search) buttons
(9, 15 – 19, 23 – 25)
f Deck B cassette holder (20 – 22, 24)
Pressing the 0 (open/close) portion opens the holder.
Display Window
1 Timer indicators
• DAILY (daily timer), SLEEP (sleep timer), REC
(recording timer), and (timer) indicators
2 GROUP indicator
3 TRACK indicator
4 Main display
• Shows the source name, frequency, etc.
5 MP3 indicator
6 Tape operation indicators
• A/B (operating deck), REC (recording), and 2 3 (tape
running) indicators
7 PRGM (program) indicator
8 SOUND MODE indicator
9 WOOFER indicator
0 CD track number indicators
- RANDOM indicator
= REPEAT mode indicators
• REPEAT, 1, 1 DISC, ALL DISC indicators
~ Tuner operation indicators
• MONO and ST (stereo) indicators
! Volume level, Subwoofer level and Sound Mode pattern
indicators
Display Window
MONO
ALL
1
DISC
REPEAT
RANDOM
PRGM
ST
GROUP TRACK
MP3
SOUND
MODE
WOOFER
1
2 3 4
5 6
7
0
8
9
-
=
~
!
Continued
EN_MXGB6&5[C]_01-08.p65 04.1.21, 6:18 PM4
5
English
Remote Control
Remote Control
1 BEEP ON/OFF button (11)
2 SLEEP button (25)
3 Number buttons (12, 16)
4 TAPE A 3 (play) button (9, 20)
Pressing this button also turns on the unit.
5 VOLUME + button (10)
6 FM/AM button (9, 12)
Pressing this button also turns on the unit.
7 AUX button (9)
Pressing this button also turns on the unit.
8 SOUND MODE button (11)
9 4/1 (reverse search/fast rewind) button
(12, 15 – 17, 19, 20)
p FADE MUTING button (10)
q 7 (stop) button (13 – 15, 18 – 22)
w STANDBY/ON button (9)
e FM MODE button (12)
MP3 button (17)
r TAPE B 3 (play) button (9, 20)
Pressing this button also turns on the unit.
t RHYTHM AX button (10)
y CD 6 (play/pause) button (9, 13 – 15, 18)
Pressing this button also turns on the unit.
u VOLUME – button (10)
i DISC SKIP button (13, 15)
o SUBWOOFER LEVEL + button (10)
; ¢/¡ (forward search/fast forward) button
(12, 15 – 17, 19, 20)
a SUBWOOFER LEVEL – button (10)
When using the remote control, point it at
the remote sensor on the front panel.
1
2
6
4
3
5
w
e
7
8
9
p
q
i
o
;
a
r
t
y
u
EN_MXGB6&5[C]_01-08.p65 04.1.21, 6:18 PM5
6
English
FM [75 ]
ANTENNA
AM
1
Attach the FM antenna to the FM [75 Ω]
coaxial terminal.
2
Extend the FM antenna.
3
Fasten it up in the position which gives you
the best reception, then fix it on the wall, etc.
About the supplied FM antenna
The FM antenna supplied with this unit can be used as temporary
measure. If reception is poor, you can connect an outdoor FM
antenna.
To connect an outdoor FM antenna
Before connecting it, disconnect the supplied FM antenna.
Getting Started
Unpacking
After unpacking, check to be sure that you have all the
following items.
The number in the parentheses indicates the quantity of the
pieces supplied.
• AM loop antenna (1)
• FM antenna (1)
• Remote control (1)
• Batteries (2)
If any is missing, consult your dealer immediately.
Putting the Batteries into the Remote Control
Insert the batteries—R6P(SUM-3)/AA(15F)—into the remote
control, by matching the polarity (+ and –) on the batteries
with the + and – markings on the battery compartment.
When the remote control can no longer operate the unit,
replace both batteries at the same time.
• DO NOT use an old battery together with a new one.
• DO NOT use different types of batteries together.
• DO NOT expose batteries to heat or flame.
• DO NOT leave the batteries in the battery
compartment when you are not going to use the
remote control for an extended period of time.
Otherwise, it will be damaged from battery leakage.
R6P(SUM-3)/AA(15F)
Connecting Antennas
FM antenna
FM antenna (supplied)
Outdoor FM antenna
(not supplied)
A 75 Ω antenna with coaxial type connector should be
used.
FM [75 ]
ANTENNA
AM
1
3
2
Continued
EN_MXGB6&5[C]_01-08.p65 04.1.21, 6:18 PM6
7
English
1
Press and hold the clamp of the AM terminal
on the rear of the unit.
2
Insert the end of the AM loop antenna cord
into the terminal.
• If the AM loop antenna wire is covered
with vinyl, remove the vinyl by twisting it
as shown in the diagram.
3
Release the finger from the clamp.
4
Turn the AM loop antenna until you have the
best reception.
To connect an outdoor AM antenna
When reception is poor, connect a single vinyl-covered wire
to the AM terminal and extend it horizontally. (The AM loop
antenna must remain connected.)
For better reception of both FM and AM
• Make sure the antenna conductors do not touch any other
terminals and connecting cords.
• Keep the antennas away from metallic parts of the unit,
connecting cords, and the AC power cord.
1
Press and hold the clamp of the speaker
terminal on the rear of the unit.
2
Insert the end of the speaker cord into the
terminal.
Match the colors (polarity): Blue (+) to blue (+) and black
(–) to black (–); red (+) to red (+) and black (–) to black
(–).
• If the wire is covered with vinyl, remove
the vinyl by twisting it as shown in the
diagram.
3
Release the finger from the clamp.
IMPORTANT:
• Use only speakers with the same speaker impedance as
indicated by the speaker terminals on the rear of the
unit.
• DO NOT connect more than one speaker to one speaker
terminal.
MAIN SPEAKER
SUB WOOFER
4-8
[ ]
6
[ ]
RR
LL
-16
AM antenna
Vinyl-covered wire
(not supplied)
AM loop antenna
(supplied)
Connecting Speakers
Speaker
cord
(red/black)
From left
main
speaker’s
terminals
Speaker cord
(red/black)
Speaker cord
(blue/black)
From right
main
speaker’s
terminals
From left
subwoofer’s
terminals
From right
subwoofer’s
terminals
1
Speaker cord
(blue/black)
Blue
Red
Black
ANTENNA
FM 75
AM
[ ]
1
For MX-GB6:
DO NOT carry the speaker by holding the tube
duct (on the top of the speaker).
Black
2, 3
2, 3
4
EN_MXGB6&5[C]_01-08.p65 04.1.21, 6:18 PM7
8
English
Connecting Other Equipment
You can connect audio equipment—used only as a playback
device.
• DO NOT connect any equipment while the power
is on.
• DO NOT plug in any equipment until all
connections are complete.
To connect audio equipment
For playing the other equipment through this unit,
connect between the audio output jack on the other
equipment and AUX jack on the front of the unit by using a
stereo mini plug cord (not supplied).
If the audio output on the other equipment is not
stereo mini plug type
Use a plug adapter to convert the stereo mini plug to the
corresponding plug of the audio output.
NOW you are ready to plug in the unit and
other connected equipment.
Canceling the Display Demonstration
When connecting the AC power cord into a wall outlet, the
unit automatically starts the display demonstration.
On the unit ONLY:
To cancel the display demonstration,
press CANCEL/DEMO while the display
demonstration is shown on the display.
When you press other buttons
The display demonstration stops temporarily. It will start
automatically again (if no operation is done for 2 minutes) until you
cancel it.
To start the display demonstration manually
Press and hold CANCEL/DEMO again for
more than 2 seconds.
To audio output
Audio equipment
Stereo mini plug cord (not supplied)
EN_MXGB6&5[C]_01-08.p65 04.1.21, 6:18 PM8
9
English
Common Operations
Turning On or Off the Power
To turn on the unit, press STANDBY/ON
so that the standby lamp goes off.
To turn off the unit (on standby), press
STANDBY/ON again so that the
standby lamp lights up.
A little power is always consumed even while the unit is on
standby.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.
When you unplug the AC power cord or if a power
failure occurs
The clock is reset to “– – : – –” soon, while the tuner preset stations
(see page 12) will be erased in a few days.
Setting the Clock
Before operating the unit any further, first set the clock built
in this unit. You can set the clock whether the unit is on or
off.
On the unit ONLY:
1
Press CLOCK/TIMER.
The hour digits start flashing on the display.
2
Press ¢ or 4 to adjust
the hour, then press SET/
DISPLAY.
The minute digits start flashing on the display.
• If you want to correct the hour after pressing SET/
DISPLAY, press CANCEL/DEMO. The hour
digits start flashing again.
3
Press ¢ or 4 to adjust
the minute, then press
SET/DISPLAY.
To check the clock time
Press and hold SET/DISPLAY for more than
2 seconds while playing any source.
• To return to the source indication, press
SET/DISPLAY.
While the time indication appears on the display
If you press a button or turn a control, the time indication returns to
the source indication.
To adjust the clock again
If you have adjusted the clock before, you need to press
CLOCK/TIMER repeatedly until “CLOCK” is selected.
• Each time you press the button, the clock/timer setting
modes change as follows:
If there is a power failure
The clock loses the setting and is reset to “– – : ––.” You need to set
the clock again.
Selecting the Sources
To listen to the radio, press FM/AM. (See page 12.)
To play back CDs, press CD 6. (See pages 13 – 19.)
To play back tapes, press TAPE A 3 or TAPE B 3. (See
page 20.)
To select the external equipment as the source, press AUX.
When you press the play button for a particular source (AUX,
FM/AM, CD 6, TAPE A 3, and TAPE B 3), the unit turns
on (and the unit starts playing the source if it is ready—
COMPU PLAY CONTROL).
ON TIME
(Daily Timer)
DAILY
Canceled
ON TIME
(Recording Timer)
CLOCK
REC
EN_MXGB6&5[C]_09-10.p65 04.1.21, 6:18 PM9
10
English
Reinforcing the Bass Sound
This function only affects the playback sound, not your
recording.
Press down the SUBWOOFER LEVEL +/–
control to increase the subwoofer sound or
up the control to decrease it.
• The subwoofer level can be adjusted
in 3 steps (LEVEL 1 — LEVEL 3).
If you press down the control to increase the
level beyond LEVEL 3, “MAX LEVEL” appears on the
display.
When using the remote control, press SUBWOOFER LEVEL
+ to increase the subwoofer sound or press SUBWOOFER
LEVEL – to decrease it.
Enjoying the Powerful Sound—RHYTHM AX
Using RHYTHM AX, harder-hitting beats intensify your
listening experience even at low sound levels.
RHYTHM AX also works even when the song has no “beat,”
such as classical music, so that you can listen to the rich
sound even at low sound levels.
This function only affects the playback sound, not your
recording.
Press down the RHYTHM AX control.
“RHYTHM AX” (twice), then “ON” appears
on the display.
• Each time you press down the control,
RHYTHM AX turns on and off alternately.
• The RHYTHM AX lamp also lights up.
When using the remote control, press RHYTHM AX.
• Each time you press the button, RHYTHM AX turns on
and off alternately.
Adjusting the Volume
You can adjust the volume level only while the unit is turned
on.
This function only affects the playback sound, not your
recording.
Turn the VOLUME control
clockwise to increase the volume or
counterclockwise to decrease it.
• The volume level can be adjusted
in 32 steps (VOL MIN, VOL 1 —
VOL 30, and VOL MAX).
When using the remote control, press VOLUME + to increase
the volume or press VOLUME – to decrease it.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers. Be sure to turn down the volume before
connecting or putting on headphones.
Always set the volume to the minimum before
starting any source. If the volume is set to
extremely high level, a sudden blast of sound can
damage your hearing, speakers and/or
headphones.
• If you have turned off (on standby) the unit with
the volume level set at more than level “15,” the
volume level will be automatically set at level “15”
next time you turn on the unit.
To turn down the volume level temporarily
Press FADE MUTING on the remote control.
The volume level gradually decreases to
“VOL MIN.”
To restore the sound, press the button again.
WOOFER indicator also shows the current subwoofer level.
Continued
WOOFER
WOOFER
EN_MXGB6&5[C]_09-10.p65 04.1.21, 6:18 PM10
11
English
Selecting the Sound Modes
This function only affects the playback sound, not your
recording.
You can select one of the 6 preset sound modes (3 surround
modes and 3 SEA—Sound Effect Amplifier—modes).
To select the sound modes, press up the
SOUND MODE control repeatedly until the
sound mode you want appears on the display.
• The SOUND MODE lamp also lights up.
• First time you press up the control, the current sound mode
appears on the display.
Each time you press up the control while a sound mode
appears on the display, the sound modes change as follows:
Surround modes*:
D.CLUB : Increases resonance and bass.
HALL : Adds depth and brilliance to the sound.
STADIUM: Adds clarity and spreads the sound, like in an
outdoor stadium.
SEA (Sound Effect Amplifier) modes:
ROCK : Boosts low and high frequency. Good for
acoustic music.
POP : Good for vocal music.
CLASSIC : Good for classical music.
OFF : Cancels the sound mode.
* Surround elements are added to the SEA elements to create
being-there feeling in your room.
When one of these modes is selected, the SOUND MODE
indicator lights up as
SOUND
MODE
.
While one of the SEA modes (SEA elements without surround
elements) is selected, the SOUND MODE indicator lights up
as
SOUND
MODE
.
SOUND MODE indicator also lights up on the display
SOUND
MODE
WOOFER
D.CLUB
(Dance CLUB)
OFF
(Canceled)
HALL STADIUM ROCK
POP
CLASSIC
When using the remote control, press SOUND
MODE to select the sound mode.
• First time you press the button, the current sound
mode appears on the display.
Each time you press the button while a sound mode appears
on the display, the sound modes change as follows:
Turning On or Off the Key-touch Tone
If you do not want the key-touch tone to beep each time you
press a button or turn a control, you can deactivate it.
• You can turn on or off the key-touch tone as follows:
–When the unit is off:
You can turn on or off the key-touch tone by operating the
unit.
–When the unit is on:
You can turn on or off the key-touch tone by operating the
unit or the remote control.
On the unit:
Press and hold BEEP for more than
2 seconds.
• Each time you press and hold the button, the key-touch
tone turns on and off alternately.
On the remote control:
Press BEEP ON/OFF when the unit is on.
• Each time you press the button, the key-touch
tone turns on and off alternately.
D.CLUB
(Dance CLUB)
OFF
(Canceled)
HALL STADIUM ROCK
POP
CLASSIC
EN_MXGB6&5[C]_11-12.p65 04.1.21, 6:18 PM11
12
English
Listening to the Radio
On the unit ONLY:
1
Tune in to the station you want to preset (in
this example, of FM 87.50).
• See “Tuning in to a Station—Auto Search.”
2
Press SET/DISPLAY.
3
Press PRESET + or
PRESET – to select a
preset number.
4
Press SET/DISPLAY again.
The tuned station in step
1
is stored in the preset number
selected in step
3
.
• Storing a new station on a used number erases the
previously stored one.
When you unplug the AC power cord or if a power
failure occurs
The preset stations will be erased in a few days. If this happens,
preset the stations again.
Tuning in to a Preset Station
1
Press FM/AM.
The unit automatically turns on and tunes in to
the previously tuned station (either FM or AM).
• Each time you press the button, the band
alternates between FM and AM.
2
Select a preset number.
On the unit:
Press PRESET + or
PRESET –.
On the remote control:
Press the number buttons.
Ex.: For preset number 5, press 5.
For preset number 15,
press +10 then 5.
For preset number 20,
press +10, then 10.
For preset number 25, press +10, +10, then 5.
For preset number 30, press +10, +10, then 10.
Tuning in to a Station—Auto Search
1
Press FM/AM.
The unit automatically turns on and tunes in to
the previously tuned station (either FM or AM).
• Each time you press the button, the band
alternates between FM and AM.
2
Start searching for stations.
On the unit:
Press and hold TUNING +
or TUNING – for more than
1 second.
On the remote control:
Press and hold ¢/¡ or
4/1 for more than 1
second.
The unit starts searching for stations and stops when a
station of sufficient signal strength is tuned in to.
If a program is broadcast in stereo, the ST (stereo)
indicator lights up.
To stop during searching, press TUNING + or TUNING –
(or ¢/¡ or 4/1 on the remote control).
When you press TUNING + or TUNING –
(or ¢/¡ or 4/1 on the remote control) briefly
and repeatedly
The frequency changes step by step.
To change the FM reception mode
When an FM stereo broadcast is hard to receive
or noisy, press FM MODE on the remote control
so that “MONO” appears and the MONO
indicator also lights up on the display. Reception
improves.
To restore the stereo effect, press FM MODE again so that
“STEREO” appears on the display.
In this stereo mode, you can hear stereo sounds when a
program is broadcast in stereo.
Presetting Stations
You can preset 30 FM and 15 AM stations.
In some cases, test frequencies have been already memorized
for the tuner since the factory examined the tuner preset
function before shipment. This is not a malfunction. You can
preset the stations you want into memory by following the
presetting method.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step
2
again.
EN_MXGB6&5[C]_11-12.p65 04.1.21, 6:18 PM12
13
English
Playing Back CDs
This unit has been designed to playback the following CDs:
• Audio CD
• CD-R (CD-Recordable)
• CD-RW (CD-ReWritable)
• MP3 disc (MP3 files recorded on a CD-R or CD-RW)*
When playing a CD-R or CD-RW
• User-edited CD-Rs (CD-Recordable) and CD-RWs
(CD-ReWritable) can be played back when they are
already “finalized.”
• Before playing back CD-Rs or CD-RWs, read their
instructions or cautions carefully.
• Some CD-Rs or CD-RWs may not be played back on this
unit because of their disc characteristics, damage or stain
on them, or if the player’s lens is dirty.
Important notices:
• In general, you will have the best performance by keeping
your CDs and the mechanism clean.
- Store CDs in their cases, and keep them in cabinets or on
shelves.
- Keep the unit’s carrousel closed when not in use.
• Continuous use of irregular shaped discs (heart-shape,
octagonal, etc.) can damage the disc rotating mechanism.
• CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than for regular CDs.
Loading CDs
1
Press CD 0.
The unit automatically turns on and the
carrousel comes out.
2
Place one or two discs correctly on the front
recesses of the disc tray, with its label side up.
• When using a CD single (8 cm), place it on the inner
recess of the disc tray.
3
If you wish to load a third disc, press
DISC CHANGE on the unit or DISC
SKIP on the remote control.
The disc tray rotates by 120˚.
4
Press CD 0 again.
The carrousel closes.
Playing Back CDs—All Disc and One Disc
You can play all loaded CDs continuously—All Disc play, or
one selected disc—One Disc play.
All Disc play
On the unit ONLY:
1
Load CDs.
• If the current playing source is not the CD player, press
CD 6, then 7 before going to the next step.
2
Press REPEAT repeatedly so that
the ALL DISC indicator lights up
on the display.
*For MP3 discs
• This unit manages files and folders on MP3 discs as
“tracks” and “albums.”
• Playback order of the MP3 files (tracks) recorded on a disc
are determined by the writing (or encoding) application;
therefore, playback order may be different from the one
you have intended while recording the files and the folders.
• This unit shows the file (track) names and the ID3v1/1.1
tags (only “Title” and “Artist”) on the display after the file
starts play; however, there is a limitation on available
characters and some file names and ID3v1/1.1 tags are not
shown correctly.
More about MP3 discs
• MP3 discs (either CD-R or CD-RW) require a longer readout
time. (It varies due to the complexity of the recording
configuration.)
• When making an MP3 disc, select ISO 9660 Level 1 or Level 2 as
the disc format.
• This unit does not support multisession recording.
• This unit can play MP3 files only with the following file
extensions— “.MP3,” “.Mp3,” “.mP3,” and “.mp3.”
• Non-MP3 files are ignored. If non-MP3 files are recorded together
with MP3 files, this unit will take a longer time to scan the disc. It
may also cause the unit to malfunction.
• Some MP3 discs may not be played back because of their disc
characteristics or recording conditions.
CORRECT
INCORRECT
For Audio CD:
ALL
DISC
GROUP
MP3
WOOFER
ALL
DISC
TRACK
WOOFER
Total Track number
Total playing time
ALL DISC indicator
MP3 indicator
For MP3 disc:
GROUP indicator appears when the MP3 playback mode is
the ALBUM mode. See also page 17.
EN_MXGB6&5[C]_13-17.p65 04.1.21, 6:18 PM13
14
English
• Each time you press the button, the indication on the
display changes as follows:
* See page 19.
3
Press one of the disc number
buttons (CD1, CD2 or CD3)
for the disc you want to start
to play from.
CD play starts from the first track of
the selected disc.
• Pressing CD 6 instead of the disc number buttons
starts playing back if a CD is on the tray.
For Audio CD:
For MP3 disc:
• When the MP3 playback mode is the ALBUM mode
(See also page 17.)
REPEAT ALL DISC* REPEAT 1 DISC*
REPEAT 1*
1 DISC
ALL DISC
(initial setting)
ALL
DISC
TRACK
WOOFER
ALL
DISC
GROUP
MP3
WOOFER
Track number of the currently playing disc flashes
(Track numbers exceeding 16 are not displayed.)
Current track number Elapsed playing time
Current track number
of the current album
Elapsed playing time
Continued
ALL
DISC
GROUP
MP3
WOOFER
ALL
DISC
GROUP
MP3
WOOFER
Current album number
• When the MP3 playback mode is the TRACK mode
(See also page 17.)
** In the TRACK mode, the unit manage only files (tracks) on the
MP3 disc. Folders (albums) are not recognized.
To stop during play, press 7.
• For MP3 disc, this unit can store the number of the track
that you have stopped playback. By pressing CD 6, you
can start playback again from the beginning of the same
track—Resume play (see also page 17).
To remove the disc, press CD 0.
CD playback sequence
When 3 CDs are loaded on the disc trays, they are played in one of
the following sequences.
• When CD1 is pressed : CD1 ] CD2 ] CD3 (then stops)
• When CD2 is pressed : CD2 ] CD3 ] CD1 (then stops)
• When CD3 is pressed : CD3 ] CD1 ] CD2 (then stops)
* When only 2 CDs are loaded, they are played in the same order,
but the disc tray without a CD is skipped.
About the CD READY lamps (CD1, CD2, and CD3)
• Each lamp corresponds to the disc tray of the same number.
• The CD READY lamp flashes while the corresponding CD is
being played.
• The CD READY lamp goes off when the unit has detected that
there is no CD on the corresponding disc tray.
ALL
DISC
MP3
WOOFER
ALL
DISC
MP3
WOOFER
Current track number**
Elapsed playing time
Current track title scrolls.
Current track title scrolls.
When the track includes the ID3v1/1.1 tags, “Title” and
“Artist” will scroll after the track title.
•“
<
TITLE
>
” appears before the content of “Title” scrolls and
“
<
ARTIST
>
” appears before the content of “Artist” scrolls.
When the track includes the ID3v1/1.1 tags, “Title” and
“Artist” will scroll after the track title.
•“
<
TITLE
>
” appears before the content of “Title” scrolls and
“
<
ARTIST
>
” appears before the content of “Artist” scrolls.
EN_MXGB6&5[C]_13-17.p65 04.1.21, 6:18 PM14
15
English
One Disc play
When 2 or 3 CDs are loaded on the disc trays, you can
select one particular disc to be played back.
On the unit ONLY:
1
Load CDs.
• If the current playing source is not the CD player,
press CD 6, then 7 before going to the next step.
2
Press REPEAT repeatedly so that
the 1 DISC indicator lights up on
the display.
• Each time you press the button, the indication on the
display changes as follows:
* See page 19.
3
Press one of the disc number
buttons (CD1, CD2 or CD3)
you want to listen.
Playback stops when all tracks of the
selected disc are played once and
resumes to All Disc play.
To stop during play, press 7.
• For MP3 disc, this unit can store the number of the track
that you have stopped playback. By pressing CD 6,
you can start playback again from the beginning of the
same track—Resume play (see also page 17).
To remove the disc, press CD 0.
To exit from One Disc play, press REPEAT repeatedly so
that ALL DISC indicator lights up on the display.
The following operations will also cancel the One
Disc play and restore All Disc play when—
• Stopping playback,
• Turning off the power,
• Ejecting the carrousel, or
• Changing the source to play.
REPEAT ALL DISC* REPEAT 1 DISC*
REPEAT 1*
1 DISC
ALL DISC
(initial setting)
1
DISC
TRACK
WOOFER
1 DISC indicator
Basic CD Operations
While playing a CD, you can do the following operations.
To exchange CDs during playback of another
Press DISC CHANGE to change the CD and the
carrousel comes out.
If you change CDs during play, the current play
will not stop until all CDs you have changed are
played.
To close the carrousel, press DISC CHANGE or CD 0.
To skip to the another CD in the carrousel
Press DISC SKIP on the remote control.
To stop play for a moment
Press CD 6.
While pausing, “PAUSE” appears on the display.
To resume play, press CD 6 again.
To locate a particular point in a track
During play, press and hold ¡ or
1.
• ¡: Fast forwards the disc.
• 1: Fast reverses the disc.
When using the remote control, press
and hold ¢/¡ or 4/1.
To go to another track
For Audio CD:
Press ¢ or 4 before or during
playback.
• ¢: Skips to the beginning of the
next or succeeding tracks.
• 4: Goes back to the beginning of
the current or previous tracks.
When using the remote control,
press ¢/¡ or 4/1.
If you press ¢ or 4 (or ¢/¡ or 4/1 on the
remote control) to select a track while playback is
stopped
The selected track starts playback.
EN_MXGB6&5[C]_13-17.p65 04.1.21, 6:18 PM15
16
English
For MP3 disc:
When the MP3 playback mode is the TRACK mode
(See also page 17.)
Press ¢ or 4 before or during
playback.
• ¢: Skips to the beginning of the
next or succeeding tracks.
• 4: Goes back to the beginning of
the current or previous tracks.
When using the remote control,
press ¢/¡ or 4/1.
If you press ¢ or 4 (or ¢/¡ or 4/1 on the
remote control) to select a track while playback is
stopped
The selected track starts playback.
To go to another album on an MP3 disc
When the MP3 playback mode is the ALBUM mode
(See also page 17.)
Press ¢ or 4 before or during
playback.
• ¢: Skips to the beginning of the
first track in the next or
succeeding albums.
• 4: Goes back to the beginning of the first track in the
previous albums.
When using the remote control,
press ¢/¡ or 4/1.
If you press ¢ or 4 (or ¢/¡ or 4/1 on the
remote control) to select an album while playback is
stopped
The first track in the selected album starts playback.
Continued
To go to another track directly using the number
buttons
For Audio CD:
Pressing the number button(s) before or
during play allows you to start playing
the selected track.
Ex.: For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 32, press +10, +10, +10, then 2.
For MP3 disc:
• When the MP3 playback mode is the TRACK mode
(See also page 17.)
Pressing the number button(s) before or
during play allows you to start playing
the selected track on the disc.
Ex.: For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 32, press +10, +10, +10, then 2.
For track number 123, press +10 twelve times, then 3.
• When the MP3 playback mode is the ALBUM mode
(See also page 17.)
Pressing the number button(s) before or
during play allows you to start playing
the selected track in the current album.
Ex.: For the 5th track in the current album,
press 5.
For the 15th track in the current album,
press +10, then 5.
For the 20th track in the current album,
press +10, then 10.
For the 32nd track in the current album,
press +10, +10, +10, then 2.
For the 123rd track in the current album,
press +10 twelve times, then 3.
If your entry is ignored
You have tried to enter a track number that does not exist on the disc
or in the album (for example, selecting track 14 in the album that
only has 12 tracks). Such entries are ignored.
EN_MXGB6&5[C]_13-17.p65 04.1.21, 6:18 PM16
17
English
Turning On or Off the Resume Play for MP3 Disc
For MP3 disc, this unit can store the number of the track that
you have stopped playback. By pressing CD 6, you can
start playback again from the beginning of the same track—
Resume play.
You can turning on and off the resume play for MP3 discs.
On the unit ONLY:
Press PROGRAM before or during playing
an MP3 disc.
• Each time you press PROGRAM, the resume play turns on
and off alternately.
If you unplug the AC power cord
The resume play is back to on.
The following operations will erase the memory of the
track number that you have stopped playback when—
• Pressing CD 0 to eject the disc.
• Pressing one of the disc number buttons (or DISC SKIP on the
remote control) to change the disc to play.
ALL
DISC
MP3
WOOFER
Changing the MP3 Playback Mode
When playing an MP3 disc, you can choose the playback
mode of the MP3 disc as follows:
• TRACK mode:
The unit recognizes only tracks (files). You can play an
MP3 disc like an Audio CD.
• ALBUM mode:
The unit recognizes tracks (files) and albums (folders) on
an MP3 disc. You can play an MP3 disc according to the
way how they are grouped.
In this mode, you can do the following operations:
• Pressing ¢ or 4 (or ¢/¡ or 4/1 on the
remote control) allows you to skip to the first track of the
previous or next albums. (See page 16.)
• Pressing the number button(s) allows you to start playing
the selected track in the current album. (See page 16.)
On the remote control ONLY:
Press MP3 before or during playing an
MP3 disc.
• Each time you press the button, the MP3 playback mode
changes between “ALBUM” and “TRACK” alternately.
ALL
DISC
GROUP
MP3
WOOFER
GROUP indicator appears when the MP3 playback mode is
the ALBUM mode.
EN_MXGB6&5[C]_13-17.p65 04.1.21, 6:18 PM17
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
JVC MX-GB6 Le manuel du propriétaire
- Catégorie
- Lecteurs de cassettes
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
- English: JVC MX-GB6 Owner's manual
Documents connexes
-
JVC RD-EZ11 Manuel utilisateur
-
-
-
-
-
-
-
JVC MX-KB4 Manuel utilisateur
-
-