Camp Chef PG24CL Warning & Instruction Booklet

Marque: Camp Chef

Modèle: PG24CL

Catégorie: Barbecues

Taper: Warning & Instruction Booklet

Ce manuel convient également à

PG36CL

www.CampChef.com | 1.800.650.2433 • Camp Chef is a registered trademark of Logan Outdoor Products

PELLET GRILL AND SMOKER

WARNING & INSTRUCTION BOOKLET

MODEL NUMBER: PG24CL

VERSION: 3

5003132

Certiﬁed to UL SUBJECT 2728

Certiﬁed to ULC/ORD-C2728

WARNING

FOR OUTDOOR USE ONLY

WARNING

If the information in this manual is not followed

exactly, a ﬁre or explosion may result causing

property damage, personal injury or loss of life.

WARNING

• To installer or person assembling this appliance:

Leave this manual with this appliance for future

reference.

• To consumer: Keep this manual with this

appliance for future reference.

This instruction manual contains important

information necessary for the proper assembly

and safe use of this product. Read and follow

all warnings and instructions before assembling

and using this appliance. Do not discard this

instruction manual.

CAUTION

Use Only Wood Pellet Fuel Speciﬁed By The

Manufacturer. Do Not Use Pellet Fuel Labeled As

Having Additives. Only use Camp Chef Premium

Pellets with the following speciﬁcations. 8,000-

8,300 BTU/LB 0.75-0.85% Ash content

CAUTION

Contact local building or ﬁre ofﬁcials about

restrictions and installation inspection

requirements in your area.

A MAJOR CAUSE OF FIRES IS FAILURE TO

MAINTAIN REQUIRED CLEARANCES (AIR SPACES)

TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST

IMPORTANCE THAT THIS PRODUCT BE INSTALLED

ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.

DANGER

1. Never operate this appliance unattended.

2. Never operate this appliance within 10 ft (3 m) of

a stored LP cylinder.

3. Never operate this appliance within 25 ft (7.5 m)

of any ﬂammable liquid.

4. If a ﬁre should occur, keep away from appliance

and immediately call your ﬁre department. Do

not attempt to extinguish an oil or grease ﬁre

with water.

Failure to follow these instructions could result

in fire, explosion or burn hazard, which could

cause property damage, personal injury or

death.

CAUTION

Always store wood pellets away from heat

producing appliances and other food containers.

Pellets should be stored in a dry environment.

WARNING

Normal use will create a buildup of ash, grease,

and creosote inside the grill. The grill must be

thoroughly cleaned after every 50 hours of use or

if a buildup of grease or creosote is noticed inside

the grill. Clean the grill by removing all internal

parts and thoroughly scrape away all grease and

creosote from all internal surfaces including the

grease drain and remove debris from the grill. The

drip tray must always be cleaned prior to turning

the grill to high or cooking in direct ﬂame mode.

Excessive buildup of grease and creosote may

result in a grease ﬁre. If a grease ﬁre does occur,

turn off the grill using the main power switch and

close the lid. Leave the lid closed until the ﬁre

extinguishes itself. If an uncontrolled ﬁre does

occur, immediately call the local ﬁre department.

Never put water on a grease ﬁre.

PG24-5 (1)

CHIMNEY CAP ASM

0420 PG24CL-3 PARTS

CHIMNEY (1)

PG24-84H

PG24CL-1 HARDWARE KIT

PG24-79 CHIMNEY HARDWARE KIT

COOKING GRATE (2)

PG24-70

1/4-20 X 3 BOLT (1)

PG24-85 (1)

CHIMNEY GASKET

1/4-20 NUT (2)

M6 X 15 BOLT (3)

M6 X 15 BOLT (4)

BURNER PULLOUT (1)

PG24-41

PULLOUT KNOB (2)

PG24-9

GREASE BUCKET (1)

PG24-11

FRONT RIGHT LEG (1)

PG24ZG-13CE

M8 X 20 BOLT (8)

M8 LOCK WASHER (8)

LEFT FRONT LEG (1)

PG24ZG-11CE

ASH CUP (1)

PG24-17

WHEEL (2)

PG24-16

WHEEL AXLE (2)

PG24-66CE

M10 FLAT WASHER (2)

M10 ACORN NUT (2)

M6 HANDLE SCREW (2)

PG24-59

THERMOMETER (1)

PG24-44

FEED GASKET (1)

PG24-34

PULOUT LOCK (1)

PG24-42

PROBE COVER (1)

PG24-54

LEFT REAR LEG (1)

PG24ZG-10CE

REAR RIGHT LEG (1)

PG24ZG-12CE

LEG PLUG (2)

PG24-69

SIDE SHELF (1)

PG36CL-1

UPPER GRATE (2)

PG24SG-5

HANDLE DEFLECTOR

(1) PG24SG-12

HANDLE BEZEL (2)

PG24-71

HANDLE (1)

PG24-57

DRIP TRAY (1)

PG24SG-4

HEAT DEFLECTOR (1)

PG24SG-2

LID

PG24SG-6 ( BLACK)

PG24SG-6B (BRONZE)

PG24SG-6S (STAINLESS)

HOPPER ASM (1)

PG24CL-2

UPPER GRATE BRACKET

(2) PG24SG-11

M6 NUT (4)

PULL ROD (1)

PG24SG-3

M8 NUT (2)

M8 FLANGE NUT (4)

M8 X 60 BOLT (4)

BOTTOM SHELF(1)

PG24WW-4

CARBON MONOXIDE WARNING

Follow these guidelines to prevent this colorless, odorless gas from poisoning you, your family or others. Know the

symptoms of carbon monoxide poisoning: headache, dizziness, weakness, nausea, vomiting, sleepiness, and confusion.

Carbon monoxide reduces the blood’s ability to carry oxygen. Low blood oxygen levels can result in loss of consciousness

and death. See a doctor if you or others develop cold or ﬂu-like symptoms while cooking or in the vicinity of this

appliance. Carbon monoxide poisoning, which can easily be mistaken for a cold or ﬂu, is often detected too late. Alcohol

consumption and drug use increase the effects of carbon monoxide poisoning. Carbon monoxide is especially toxic to

mother and child during pregnancy, infants, the elderly, smokers and people with blood or circulatory system problems,

such as anemia, or heart disease.

LID MAGNET (1)

PGC24-18

POWER CORD (1)

PG24-48

HOPPER HANDLE (1)

PGC24-12

M6 X 15 BOLT (4)

M6 NUT (2)

PULLOUT KNOB (1)

PG24-9

PULLOUT LOCK (1)

PG24-42

BOTTLE OPENER (1)

BTOP-1

AUGER (1)

PGC24-8

AUGER PIN W/NUT (1)

PG24-25

AUGER BUSHING (1)

PG24-23

AUGER MOTOR WITH IMPELLER (1)

PG24-24

AUGER IMPELLER (1)

PG24-49

HEATING ROD (1)

PG24-21

BURNER (1)

PG24-78

M4.2 X 10 SCREW (4)

BLOWER IMPELLER (1)

PG24-27

M4.2 X 10 SCREW (4)

BLOWER MOTOR WITH IMPELLER (1)

PG24-26

MEAT PROBE (4)

PG24-86

M4 X 10 SCREW (2)

HOPPER LID (1)

PG24CL-3 (BLACK)

AUGER GUARD (1)

PG24CL-4

GUARD PLATE (1)

PG24CL-5

HOPPER WINDOW (1)

PG24CL-6

WIFI CONTROLER (1)

PG24CL-7

HOPPER CLEANOUT (1)

PG24CL-8

digital readout is measured near the cooking surface on

the left side of the grill. The actual temperature inside

the cooking chamber will vary slightly throughout.

19. Do not use accessories not specified for use with

appliance.

20. Never use gasoline, gasoline-type lantern fuel,

kerosene, charcoal lighter fluid, or similar liquids to

start or freshen up a fire in this appliance. Keep all

such liquids well away from the appliance when in use.

21. Ashes should be placed in a metal container with a

tight fitting lid. The closed container of ashes should

be placed on a non combustible floor or on the ground,

well away from all combustible materials, pending final

disposal. When the ashes are disposed by burial in soil

or otherwise locally dispersed they should be retained

in the closed container until all cinders have thoroughly

cooled.

22. Creosote – Formation and need for removal. When wood

pellets are burned slowly, they produce tar and other

organic vapors that combine with expelled moisture

to form creosote. The creosote vapors condense in a

relatively cool oven flue and exhaust hood of a slow

burning fire. As a result, creosote residue accumulates

on the flue lining and exhaust hood. When ignited,

this creosote makes an extremely hot fire. The grease

duct should be inspected every 50 hours to determine

when grease and/or creosote build-up has occurred.

When grease or creosote has accumulated, it should be

removed to reduce risk of fire.

DANGER

Do not work on this grill if it is plugged in. Electric shock

may occur resulting in death or serious injury.

1. Do NOT leave this appliance unattended while in use.

The user must remain in the immediate area of the

product and have a clear view of the product at all times

during operation.

2. Keep children and pets away from grill at all times.

3. The use of alcohol, prescription or non-prescription drugs

may impair your ability to properly assemble or safely

operate this appliance.

4. For OUTDOOR use only. Do NOT use in a building,

garage or any other enclosed area. Do NOT use in or on

recreational vehicles or boats. NEVER use this appliance

as a heater.

5. Do not operate appliance under ANY overhead

construction. Keep a minimum clearance of 36 inches

(0.9 m) from the sides, front and back of appliance to

ANY construction. Keep the area clear of all combustible

material and flammable liquids, including wood, dry

plants and grass, brush, paper, and canvas.

6. This product is not intended for commercial use.

7. Always allow the appliance to cool before covering with

the patio cover.

8. Always cover the appliance, with patio cover (if

supplied), when not in use.

9. Always unplug grill before installing patio cover.

10. Use only on a level, stable non-combustible surface like

bricks, concrete or dirt. Do not use this appliance on

any surface that will burn or melt like wood, asphalt,

vinyl or plastic.

11. Make sure burner clean-out is closed before starting

the grill.

12. Make sure the grease bucket is in place before starting

the grill.

13. In the event of a fire unplug the grill from the power

supply, close the lid, and leave it closed until the fire

goes out. After allowing the grill to cool, follow the

cleaning instructions before the next use.

14. Use only food grade hardwood pellets manufactured for

use in pellet grills. Using softwood or heating pellets

will void your warranty.

15. Do not allow the hopper to run out of pellets. Pellets

can be added at any time. The hopper will hold

approximately 22 pounds of pellets. The pellet usage

will vary greatly depending on the ambient temperature

as well as cooking temperature.

16. It is recommended that you not store pellets in the

hopper for extended periods as they may absorb

moisture from the air and clog the auger.

17. Keep the lid closed during cooking. The grill is designed

to cook with the lid closed.

18. Note that the cooking temperature displayed on the

using Qty (1) M6 nut. Thread second nut onto bolt leaving

approximately 1.5” to the top of the cap. Thread cap

assembly down into the chimney bracket until the lower

nut hits the bracket. See Fig 3.

M8 X 60 BOLT

M8 FLANGE NUT

M6 X 15 SCREW

CHIMNEY GASKET

M6 NUT

M6 X 76 BOLT

FIG. 3

4. The height of the chimney cap can be adjusted for

summer and winter. In the summer the gap should be

approximately 1-1/2”. In the winter the gap should be

approximately ½”.

5. Tighten all hardware.

INSTALL HANDLE

1. Install the handle as shown in Fig 4.

2. Tighten all hardware.

M6 HANDLE SCREW (2)

HANDLE DEFLECTOR

HANDLE

HANDLE BEZEL (2)

M6 X 15 SCREW

GREASE BUCKET

ASH CUP

FIG. 4

INSTALL HOPPER HANDLE

1. Install hopper handle as shown in Fig. 5.

FIG. 5

ASSEMBLY INSTRUCTIONS

Remove all loose parts from the inside of the grill and

hopper. Lay a blanket or piece of cardboard down to protect

the grill.

ATTACH THE LEGS

With the help of another person ﬂip the grill upside down

on the blanket or cardboard. The grill lid and hopper lid will

swing open when doing this so be careful not to damage

the lids. The grill may also want to roll on its lid so one

person should hold the grill steady while the other person

assembles the bottom legs and wheels.

1. Lay the grill on its back.

2. Install each of the 4 legs as shown in Fig 1. Make sure

the legs with wheels are attached to the right side of

the grill with the wheels facing out. Note: Front legs are

marked with an F and back legs are marked with a B.

3. Stand the grill upright

4. Tighten all hardware.

FIG. 1

M8 X 20 BOLT

M8 LOCK WASHER

ATTACH BOTTOM SHELF

1. Install bottom shelf as shown in Fig. 2 by installing

hardware in each of the 4 corners.

2. Tighten hardware.

FIG. 2

M8 X 60 BOLT

M8 FLANGE NUT

M6 X 15 SCREW

CHIMNEY GASKET

M6 NUT

M6 X 76 BOLT

ATTACH CHIMNEY AND CHIMNEY CAP

1. Install chimney to grill as shown in Fig 3. Make sure to

install the gasket between the grill and the chimney.

2. Tighten all hardware.

3. Install M6 x 76 Bolt through chimney cap and secure

INSTALL HOPPER GUARD AND LID

1. Install guard and lid as shown in Fig. 6. The tab on the

hopper should be inserted into the slot on the guard. Use

screws to secure hopper guard and lid to the hopper.

M4 X 10 SCREW (2)

HOPPER LID (1)

HOPPER GUARD (1)

FIG. 6

HOPPER LID (1)

M4 X 10 SCREW (2)

HOPPER GUARD (1)

INSTALL SHELF BRACKET

1. Install the bracket as shown in Fig 7.

2. Tighten all hardware.

M6 X 15 SCREW (4)

M6 FLANGE NUT (4)

UPPER GRATE BKT (2)

PG24SG-11

FIG. 7

INSTALL SHELF

(Optional-Do not install if installing sear box)

1. Install shelf as shown in Fig 8.

2. Tighten all hardware

M6 HANDLE SCREW (2)

HANDLE DEFLECTOR

HANDLE

HANDLE BEZEL (2)

GREASE BUCKET

M6 X 15 SCREW

ASH CUP

FIG. 8

GREASE BUCKET

1. Hang grease bucket from tube as shown in Fig 9.

ASH CUP

1. Install Ash Cup as shown in Fig 9. Never use grill without

Ash Cup in place.

ASH CUP

GREASE BUCKET

FIG. 9

INSTALL DRIP TRAY

1. Install the Drip Tray as shown in Fig 10 and Fig11.

HEAT DEFLECTOR

DRIP TRAY

HEAT DEFLECTOR

DRIP TRAY

FIG. 10

HEAT DEFLECTOR

DRIP TRAY

HEAT DEFLECTOR

DRIP TRA

FIG. 11

WARMING RACK AND COOKING GRATE

1. Install the cooking grate as shown in Fig 12.

UPPER GRATE (2)

PG24SG-5

LOWER GRATE (2)

PG24-70

FIG. 12

CLEAN-OUT KNOB ASSEMBLY INSTALLATION

Hand tighten the burner clean-out knob as shown in Fig 13.

FIG. 13

PG24-9 (1)

BURNER PULLOUT KNOB

CLEAN-OUT PORT KNOB

1. Clean-out Port knob must be pushed in when grill is on.

Make sure pullout lock is pushed down and locks the

knob to prevent inadvertent opening of the clean-out port.

See Fig 14.

2. Lift pullout lock and pull clean-out port knob to empty

ash into ash cup. See Fig 15

3. See instructions for burner clean-out.

WARMING RACK

COOKING GRATE

CLEANOUT PORT CLOSED

CLEANOUT PORT OPEN

FIG. 14

WARMING RACK

COOKING GRATE

CLEANOUT PORT CLOSED

CLEANOUT PORT OPEN

FIG. 15

HOPPER CLEAN-OUT KNOB ASSEMBLY INSTALLATION

Hand tighten the hopper clean-out knob as shown in Fig 16.

PG24-9 (1)

PULLOUT KNOB

FIG. 16

BURNER CLEAN-OUT

Before each use the burner should be cleaned out by lifting

the pullout lock and pulling the clean-out port knob on the

right side of the grill to open the burner clean-out. This will

allow the ash from previous use to fall into the cup under

the grill. The cup should be removed and emptied and then

reinstalled before each use.

DANGER

Never Operate the Pellet grill without the ash cup in place.

Make sure the burner clean-out port is closed and locked

before starting the grill.

WARMING RACK

COOKING GRATE

CLEANOUT PORT CLOSED

CLEANOUT PORT OPEN

Never open the burner clean-out port when the grill is hot.

After cleaning out the burner make sure to close the burner

clean-out by pushing the clean-out port knob in on the right

side of the grill. Make sure to lift the pullout lock and push

the clean-out port knob all the way in and lock in place

with the pullout lock. Every 50 hours of use, remove the grill

grates, grease tray, and heat deﬂector and clean the inside

of the grill. If you notice a lot of ash blowing around in the

grill it is time to vacuum it out.

FILLING THE AUGER TUBE

CAUTION: ONLY USE THE FEED SETTING WHEN HOPPER HAS

RUN OUT OF PELLETS. FEED SETTING IS NOT FOR NORMAL USE.

The ﬁrst time you use your grill or any time the hopper has

ran out of pellets you will need to ﬁll the auger tube. This

simply means you must ﬁll the auger tube with pellets

until pellets reach the burner. This is done by selecting

FEED from the main menu. This will turn the auger on and

the controller will display “FEED”. The auger will remain

on for no more than 7 minutes. This is ample time for the

pellets to reach the burner. It is easiest to open the burner

clean-out by pulling the knob on the right side of the grill.

Once you hear pellets dropping into the cup you can close

the clean-out port by pushing the knob on the right side of

the grill and then select your cooking temperature. (Never

operate grill without the ash cup in place). Always make

sure the burner clean-out port is closed by pushing in the

knob on the right side of the grill before selecting any of the

cook settings. Never open the burner clean-out port when

the grill is hot.

APP QUICK START GUIDE

1. Download the Camp Chef APP from the Apple APP store or

Android Play Store.

2. Turn the Grill controller on using the main power switch.

3. Open the Camp Chef APP and follow the setup instructions for

connecting the grill to your home 2.4 GHz WiFi network.

Warning - Do NOT leave this appliance unattended while

in use. The user must remain in the immediate area of the

product and have a clear view of the product at all times

during operation.

Note - Some functions are only available from the controller.

If attempting to start the grill from the APP it will prompt

you to conﬁrm starting the grill from the controller.

Temperature and Smoke settings can be adjusted from the

APP. Shutdown can also be performed from the APP.

For more information visit https:/www.campchef.com/app

CONTROLLER EXPLANATION

POWER SWITCH

Used to turn the main power onto the pellet grill. “O” is Off.

“-“ is On. See Fig. 17

Fig. 17

CONTROLLER FUNCTIONS

Rotate the dial to scroll through menus, adjust temperature,

or smoke settings. Press the dial to select.

SHUTDOWN

This setting must be used after each use. Select SHUTDOWN

from the main menu. The fan will remain on for up to 20

minutes. This setting will burn up any extra pellets in the

burner and cool down the grill. Do not turn the main power

switch off when the grill is hot.

FEED - Select FEED from the main menu. This setting is

used to feed pellets to the burner. It will be used the ﬁrst

time you use the grill to ﬁll the auger tube and any time

you may inadvertently run the hopper out of pellets. See

instructions on ﬁlling the auger tube.

SET TEMP LOW SMOKE - Select SET TEMP from the main

menu. Rotate dial to LOW SMOKE and press to conﬁrm. This

setting is used for smoking foods at an average temperature

of 160F. This setting will produce large amounts of smoke.

SET TEMP HIGH SMOKE - - Select SET TEMP from the main

menu. Rotate dial to HIGH SMOKE and press to conﬁrm. This

setting is used for smoking foods at an average temperature

of 220F. This setting will produce large amounts of smoke.

SET TEMP 160F TO 450F - Select SET TEMP from the main

menu. Rotate dial to the desired temperature and press to

conﬁrm.

SET TEMP HIGH - Select SET TEMP from the main menu.

Rotate dial to HIGH and press to conﬁrm. This setting can

be used to achieve temperatures up to 500F depending on

ambient temperatures.

SET SMOKE – The SET SMOKE setting is available for

temperatures from 160F – 350F. Select SET SMOKE from

the main menu. Rotate dial to the desired SMOKE SETTING

and press to conﬁrm. The SMOKE SETTING can be adjusted

from 1-10. A smoke setting of 1 will produce less smoke and

maintain a more even temperature. As the smoke setting

is increased more smoke will be produced. Note that as the

smoke setting is increased temperature ﬂuctuations will

increase.

BREAKING IN THE GRILL

We suggest turning the grill to 350F for ½ hour before

cooking on the grill for the ﬁrst time. This will burn off any

manufacturing oils and cure the paint. Make sure to follow

the instructions for ﬁlling the auger tube before breaking in

the grill.

WARNING

Always start the grill with the lid open. The lid must be

closed after the start cycle.

COOKING

Once the auger tube has been properly ﬁlled you can begin

cooking by selecting SET TEMP from the main menu and

setting the desired temperature. Upon conﬁrming the set

temperature the grill will go into the Startup mode. The

control will display START during the startup cycle. After 6

minutes the control panel will change to the temperature

display screen.

WARNING

Do not over-ﬁre the grill by over feeding pellets into

the burner prior to startup. If ﬂame is inadvertently

extinguished never restart the grill without ﬁrst cleaning out

the burner. Improper use can cause an uncontrolled ﬁre.

DIRECT FLAME MODE

Pull grill knob out all the way to allow direct heat as shown

in Fig 18. Best for burgers and steaks.

Fig. 18

WARNING

Always clean grease tray to remove excess grease drippings

prior to cooking in Direct Flame Mode. A dirty grease tray

may result in excessive ﬂare ups or grease ﬁre. If grease ﬁre

does occur, turn off grill using the main power switch and

close the lid. Leave the lid closed until ﬁre is extinguished.

If an uncontrollable ﬁre does occur, immediately call local

ﬁre department. Never put water on the ﬁre.

INDIRECT FLAME MODE

Push grill knob in all the way for indirect heat as shown in

Fig 19. Best for chicken, slow smoking and low temps.

Fig. 19

SHUTDOWN

When you are done cooking select SHUTDOWN from the

main menu. The display screen will display SHUTDOWN. In

this setting the fan will remain on for 20 minutes to ﬁnish

burning any pellets in the burner and cool the grill down.

After 20 minutes the display screen will turn off. At this

point the main power switch should be switched to off.

Before grill can be used, the power switch must be turned

off and back on.

BYPASS MODE

The bypass may be used if there is a power failure, or

the grill is accidentally turned off, or anytime you need to

restart the grill and it is still hot. The bypass mode should

only be used if the grill has been off less than 3-4 minutes.

This method is used to bypass the normal startup mode and

get the grill cooking again quickly. The burner must still

be hot enough to ignite new pellets or this method will not

work. BYPASS can be selected during the initial startup of

the grill only by selecting BYPASS from the STARTUP screen.

If the grill fails to ignite using the bypass mode then restart

the grill using the normal startup procedures.

MEAT PROBES

This smoker has built in meat probes to measure the

temperature of the food as it is being cooked. To use these

probes insert the wire through the stainless ﬂaps on the

side of the ﬁrebox. Insert the probes into the food. Plug the

connectors into the receptacles on the side of the control

panel. If the probes are not installed correctly or the probe is

bad no temperature will display.

PROBE

PROBE HOLE

CAUTION

Do not use meat probes when grill temperature exceeds

350˚F. Damage to the probes may occur.

Do not allow meat probe wires to lie in the direct heat

zones (as shown by shaded areas).

Direct heat will damage the meat probe wires. Always

route the meat probes through ports on the side of the

grill. Do not submerge wire in water. Not dishwasher safe.

CLEANING

Clean grates using a wire grill brush. This should be

done with each use. DO NOT use oven cleaner or abrasive

cleaners on the painted grill surfaces. Use warm soapy

water on all painted surfaces. Clean grease pan, grease

trough, and grease drain tube occasionally. A spatula can

be used to scrape excess grease and a grill brush to brush

clean. Do not allow grease to build up on the grease tray or

in the grease trough as this can cause ﬂare-ups inside the

grill. Make sure not to obstruct the ﬂow of grease off of the

tray and into the grease trough. Make sure not to block the

airﬂow to the temperature sensor on the left side of the grill.

WARNING

Normal use will create a buildup of ash, grease, and

creosote inside the grill. The grill must be thoroughly

cleaned after every 50 hours of use or if a buildup of

grease or creosote is noticed inside the grill. Clean the

grill by removing all internal parts and thoroughly scrape

away all grease and creosote from all internal surfaces

including the grease drain and remove debris from

the grill. The drip tray must always be cleaned prior to

turning the grill to high or cooking in direct ﬂame mode.

Excessive buildup of grease and creosote may result in

a grease ﬁre. If a grease ﬁre does occur, turn off the grill

using the main power switch and close the lid. Leave

the lid closed until the ﬁre extinguishes itself. If an

uncontrolled ﬁre does occur, immediately call the local

ﬁre department. Never put water on a grease ﬁre.

CHIMNEY CLEANING

When wood pellets are burned slowly, they produce tar and

other organic vapors that combine with expelled moisture to

form creosote. The creosote vapors condense in a relatively

cool oven chimney of a slow burning ﬁre. As a result,

creosote residue accumulates on the chimney. When ignited,

this creosote makes an extremely hot ﬁre. The chimney

should be inspected every 50 hours of use to determine

when grease and or creosote buildup has occurred. When

grease or creosote has accumulated, it should be removed

to reduce risk of ﬁre. Use a wire brush to clean the screen

area of the chimney outlet on the inside of the grill with

every 50 hours of use. The chimney must be removed and

thoroughly cleaned to remove creosote and grease buildup

every 200 hours of use.

TROUBLESHOOTING

GRILL DOES NOT TURN ON.

Grill fails to turn on after switching the power button to the

on position.

1. Make sure the grill is plugged into a powered outlet and

the switch is in the on position “-”. Check the circuit

breaker and/or GFCI switch. Test the outlet using another

appliance.

2. Unplug the grill and check the fuse located in the bottom

of the control panel. If the fuse is blown replace only

with 4.0 Amp 125V 5x20mm Fast Blow Fuse. Typical fuse

marking will be 4A125V, F4A125V, 4A250V, or F4A250V.

Make sure to conﬁrm they are a Fast Blow Fuse. Actual

fuse dimensions are 5.2x20mm.

If problem cannot be resolved please call customer service.

CONTROLLER DISPLAY DOES NOT TURN ON AFTER UPDATE

1. Make sure the grill is plugged into a powered outlet and

the switch is in the on (“-”) position.

2. Leave the switch in the on position for 2 minutes. The

screen may be blank but it is completing the update.

3. If display does not turn on, cycle power on the controller.

Wait 3 second in the off position. The screen should now

come on.

CONNECTION TIME OUT

1. Exit and close the APP.

2. Cycle the power on the controller.

3. Wait 1 minute and the WiFi logo on the controller will

light up.

4. At this point open the APP and follow the APP QUICK

START GUIDE for connection instructions.

GRILL DOES NOT HEAT UP OR CONTROLLER DISPLAYS

FLAME ERROR

1. Turn Power Off

2. Check hopper for pellets

3. Check ﬁrebox to see if there are pellets in the ﬁrebox.

The easiest way to do this is to pull the burner clean-out

lever. Then remove the cup from the bottom of the grill

and check for pellets. Use a vacuum to clean-out any

pellets that may be in the bottom of the grill.

A. If there are a lot of pellets in the cup. Reinstall the

cup and close the burner clean-out, remove the grill

grates, grease tray, and heat deﬂector and vacuum out

any pellets in the bottom of the grill. Try restarting the

grill. If restarting the grill does not work and pellets are

getting to the burner cup the heating rod may need to be

replaced.

B. If there are few or no pellets in the cup then turn the dial

to the feed position and see if pellets fall out the bottom

of the burner. If there are no pellets check to see if the

auger is turning. If the auger motor is turning but the

auger is not there may be a sheared auger pin. You can

determine if the auger motor is turning by watching the

small white fan at the end of the auger motor under the

hopper. If the white fan is turning the auger motor is on.

If the white fan is turning and the auger is not you will

need to replace the auger pin.

If problem cannot be resolved please call customer service.

CONTROLLER DISPLAYS SENSOR ERROR

1. Turn the power off and unplug the grill.

2. Check to make sure the sensor inside of the grill is

connected properly to the electronic board under the

hopper.

3. Call customer service for a replacement sensor.

PROBE TEMPERATURES DO NOT DISPLAY

1. Make sure the meat thermometer is connected properly to

the controller.

2. Call customer service for a replacement meat

thermometer.

CONTROLLER DISPLAYS OVER TEMP.

1. This happens if the internal temperature of the grill

exceeds a normal operating temperature. The grill must

be cleaned before attempting to start the grill.

LIMITED WARRANTY

Camp Chef No-Hassle Warranty

Here at Camp Chef we stand by our products and take pride in our

customer service. Because of this, your new Camp Chef product comes

with a No-Hassle Warranty. We warrant that our products will be free from

defects in all materials and workmanship (excluding paint and ﬁnish) for

the Warranty Coverage Period described below. This warranty is extended

only to the original consumer purchaser. During the Warranty Coverage

Period, we will (at our sole option) replace any defective part or product

covered by this warranty when provided with proof of purchase. The

replacement will be without charge.

Required Maintenance:

Clean your product after each use to maintain its ﬁnish and prolong its

lifespan. Wipe away all grease and ashes. Keep metal products free of

moisture, salts, acids and harsh ﬂuctuations in temperature. Product

paint and other ﬁnishes are not covered by this warranty. The exterior

ﬁnish of the product will wear down over time.

Coverage Details:

Warranty does not cover normal wear of parts or damage caused by

misuse, abuse, overheating and alteration. No alterations are covered in

this warranty. Camp Chef is not responsible for any loss due to neglectful

operation. Furthermore, this warranty does not cover products damaged

or rendered defective due to accident, misuse, abuse, modiﬁcation, water

damage, neglect, improper handling or storage, improper maintenance

or installation, incorporation of third party components or exposure to

weather, natural disasters such as earthquakes, hurricanes, tornadoes,

ﬂoods, lightning, ﬁres, or failure to follow instructions for use.

ANY WARRANTIES IMPLIED BY LAW SHALL IN NO EVENT EXTEND BEYOND

DURATION OF THIS EXPRESS WARRANTY. Some States do not allow

limitations on how long an implied warranty lasts, so the above limitation

may not apply to you. REPAIR OR REPLACEMENT AS PROVIDED HEREIN IS

YOUR EXCLUSIVE REMEDY FOR ANY DEFECTIVE PRODUCT. IN NO EVENT

SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES OF ANY KIND ARISING OUT OF THE PURCHASE OR USE OF

THIS PRODUCT, WHETHER BASED UPON CONTRACT, TORT, STATUTE OR

OTHERWISE. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion

may not apply to you. This warranty gives you speciﬁc legal rights, and

you may also have other rights which vary from State to State.

Please keep all original sales receipts from the authorized dealer. Proof

of purchase is required to obtain warranty services. Any parts or products

returned without written authorization will be discarded without notice.

To obtain warranty services submit a warranty request at

www.campchef.com/warranty-information, email: [email protected]

or call (800) 650-2433. Our English speaking Product Specialists are happy

to help, Monday-Friday 7 AM – 5 PM MST.

Warranty applies to the United States and Canada.

WARRANTY COVERAGE PERIODS

Pellet Grills 3 years from purchase date

Stoves 1 year from purchase date

Fire Pits 1 year from purchase date

Water Heaters 1 year from purchase date

Movie Screens 1 year from purchase date

All other items & accessories 90 days from purchase date

White

Black

4A 125V

4 amp 125V

5 x 20 MM

Fast Blow Fuse

Auger Motor

Blower Fan

Burner

Controller

RTD Sensor

Power Cord

White

Red

White

Orange

White

Purple

Hot Rod

MOLEX Connector

CAUTION

Please note that any changes or modiﬁcations of this product not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1 this device

may not cause harmful interference, and 2 this device must accept any interference received, including interference that

may cause undesired operation.

Logan Outdoor Products LLC., dba Camp Chef, 3985 N 75 W, Hyde Park, UT 84318, USA, 1.800.650.2433

www.CampChef.com | 1.800.650.2433 • Camp Chef is a registered trademark of Logan Outdoor Products

BARBECUE À GRANULES ET FUMOIR

NOTICE D’UTILISATION ET AVERTISSEMENTS

NUMÉRO DE MODÈLE: PG24CL

VERSION: 3

5003132

Certiﬁed to UL SUBJECT 2728

Certiﬁed to ULC/ORD-C2728

AVERTISSEMENT

DESTINÉ À UN USAGE EN PLEIN

AIR UNIQUEMENT

AVERTISSEMENT

Le non-respect à la lettre des renseignements

ﬁgurant dans la présente notice peut entraîner

un incendie ou une explosion qui pourrait

occasionner des dommages matériels, des

blessures corporelles ou la mort.

AVERTISSEMENT

• À l’attention de l’installateur ou de la personne

chargée d’assembler cet appareil : conserver

la présente notice d’utilisation avec l’appareil

pour un usage ultérieur.

• À l’attention du consommateur : conserver la

présente notice d’utilisation avec l’appareil

pour un usage ultérieur.

La présente notice d’utilisation contient des

informations importantes, nécessaires au

montage correct et à l’utilisation sécuritaire

de ce produit. Lire et respecter l’ensemble des

avertissements et consignes avant le montage

et l’utilisation de cet appareil. Ne pas jeter la

présente notice d’utilisation.

ATTENTION

Utiliser uniquement les granules de bois indiqués

par le fabricant. Ne pas utiliser de granules de

bois dont les spéciﬁcations indiquent la présence

d’additifs. Utiliser uniquement les granules

Camp Chef de première qualité répondant aux

spéciﬁcations suivantes. 8 000 à 8 300 BTU/LB.

Taux de cendres de 0,75 à 0,85 % (8,000-8,300

BTU/LB 0.75-0.85% ash content).

ATTENTION

Contacter les autorités locales du bâtiment ou de la

protection incendie pour connaître les restrictions et les

exigences d’inspection en vigueur dans votre région.

LE NON-RESPECT DES DÉGAGEMENTS OBLIGATOIRES

(ESPACES VIDES) PAR RAPPORT AUX MATÉRIAUX

COMBUSTIBLES EST UNE DES PRINCIPALES CAUSE

D’INCENDIE. IL EST EXTRÊMEMENT IMPORTANT

D’INSTALLER CE PRODUIT DANS LE STRICT RESPECT

DE CES CONSIGNES.

AVERTISSEMENT

1. Ne jamais faire fonctionner cet appareil sans

surveillance.

2. Ne jamais utiliser cet appareil à moins de 3 m

(10 pi) d’une bouteille de GPL entreposée.

3. Ne jamais utiliser le présent appareil à moins de

7,5 m (25 pi) de tout liquide inﬂammable.

4. En cas d’incendie, rester à bonne distance de

l’appareil et appeler immédiatement le service

des incendies. Ne pas essayer d’éteindre un feu

d’huile ou de graisse au moyen d’eau.

Le non-respect de ces consignes peut entraîner

des dommages matériels, des blessures corporelles

ou la mort pouvant résulter d’un incendie, d’une

explosion ou d’un danger de brûlure.

ATTENTION

Entreposer en permanence les granules de bois

à l’abri des appareils produisant de la chaleur

et d’autres récipients alimentaires. Les granules

doivent être entreposés dans un endroit sec.

AVERTISSEMENT

Une utilisation normale créera une accumulation

de cendres, de graisse et de créosote dans le

barbecue. Le barbecue doit être nettoyé à fond

toutes les 50 heures d’utilisation ou si une

accumulation de graisse ou de créosote est

observée à l’intérieur du barbecue. Nettoyer le

barbecue en enlevant toutes les pièces internes

et enlever soigneusement toutes les graisses

et la créosote de toutes les surfaces internes, y

compris le tuyau d’évacuation des graisses et

enlever les débris du barbecue. La lèchefrite doit

toujours être nettoyée avant de mettre le barbecue

en position haute ou de cuire en mode ﬂamme

directe. Une accumulation excessive de graisse et

de créosote peut provoquer un feu de graisse. En

cas d’incendie provoqué par la graisse, éteindre

l’appareil au niveau de l’interrupteur principal

et fermer le couvercle. Laisser le couvercle fermé

jusqu’à l’extinction totale du feu. En cas d’incendie

incontrôlable, appeler immédiatement le service

local des incendies. Ne jamais verser de l’eau sur

un feu de graisse.

PG24-5 (1)

ENSEMBLE DU CHAPEAU

DE LA CHEMINÉE

0420 PG24CL PARTS

CHEMINÉE (1)

PG24-84H

PG24CL-1 ENSEMBLE DE QUINCAILLERIE

PG24-79 ENSEMBLE DE LA QUINCAILLERIE

POUR LA CHEMINÉE

GRILLE DE CUISSON (2)

PG24-70

BOULON 1/4-20 X 3 (1)

ÉCROU 1/4-20 (2)

BOULON M6 X 15 (4)

TRAPPE DU BRÛLEUR (1)

PG24-41

BOUTON DE TRAPPE (2)

PG24-9

SEAU DE COLLECTE DES GRAISSES (1)

PG24-11

PIED AVANT DROIT (1)

PG24ZG-13CE

BOULON M8 X 20 (8)

RONDELLE FREIN M8 (8)

PIED AVANT GAUCHE (1)

PG24ZG-11CE

RÉCIPIENT À CENDRES (1)

PG24-17

ROULETTE (2)

PG24-16

AXE DE ROULETTE (2)

PG24-66CE

RONDELLE PLATE M10 (2)

ÉCROU BORGNE M10 (2)

VIS DE LA POIGNÉE M6 (2)

PG24-59

THERMOMÈTRE (1)

PG24-44

JOINT DU SYSTÈME

D'ALIMENTATION (1)

PG24-34

SYSTÈME DE BLOCAGE DE

LA TRAPPE DU BRÛLEUR (1)

PG24-42

COUVERCLE DE SONDE (1)

PG24-54

PIED ARRIÈRE GAUCHE (1)

PG24ZG-10CE

PIED ARRIÈRE DROIT (1)

PG24ZG-12CE

BOUCHON DU PIED (2)

PG24-69

ÉTAGÈRE LATÉRALE (1)

PG36CL-1

GRILLE SUPÉRIEURE (2)

PG24SG-5

DÉFLECTEUR DE LA POIGNÉE

(1) PG24SG-12

COLLERETTE D’ENCASTREMENT

DE LA POIGNÉE (2)

PG24-71

POIGNÉE (1)

PG24-57

LÈCHEFRITE (1)

PG24SG-4

DÉFLECTEUR DE CHALEUR (1)

PG24SG-2

COUVERCLE

PG24SG-6 ( NOIR)

PG24SG-6B (BRONZE)

PG24SG-6S (ACIER INOXYDABLE)

ENSEMBLE DU

RÉSERVOIR (1)

PG24CL-2

SUPPORT DE GRILLE SUPÉRIEURE

(2) PG24SG-11

ÉCROU M6 (4)

TIGE DU DÉFLECTEUR (1)

PG24SG-3

ÉCROU M8 (2)

ÉCROU À EMBASE M8 (4)

BOULON M8 X 60 (4)

PLATEAU DU BAS (1)

PG24WW-4

PG24-85 (1)

JOINT DE LA CHEMINÉE

BOULON M6 X 15 (3)

AVERTISSEMENT CONCERNANT LE MONOXYDE DE CARBONE

Respecter les présentes directives pour éviter de vous faire intoxiquer et d’intoxiquer vos proches par ce gaz incolore

et inodore. Vous devez connaître les symptômes d’une intoxication au monoxyde de carbone : il s’agit de maux de tête,

de vertiges, de faiblesses, de nausées, de vomissements, de somnolence et de confusion. Le monoxyde de carbone

réduit la capacité sanguine pour transporter l’oxygène. Un faible taux d’oxygène dans le sang peut entraîner des

pertes de connaissance, voire la mort. Consulter un médecin si vous ou autrui développez des symptômes du rhume ou

s’apparentant à la grippe en cuisinant à proximité de cet appareil. Une intoxication au monoxyde de carbone, souvent

confondue par erreur avec un rhume ou la grippe, est souvent détectée trop tard. La consommation d’alcool ou de

drogues renforce les effets de l’intoxication au monoxyde de carbone. Le monoxyde de carbone est particulièrement

toxique pour les femmes enceintes et leur fœtus, les jeunes enfants, les personnes âgées, les fumeurs et les personnes

souffrant de troubles sanguins ou circulatoires, comme l’anémie ou des maladies cardiaques.

AIMANT DE COUVERCLE (1)

PGC24-18

CORDON D'ALIMENTATION (1)

PG24-48

POIGNÉE DU RÉSER

VOIR (1)

PGC24-12

BOULON M6 X 15 (4)

ÉCROU M6 (2)

BOUTON DE TRAPPE (1)

PG24-9

SYSTÈME DE BLOCAGE DE LA TIGE DE

NETTOYAGE DU RÉSERVOIR (1)

PG24-42

DÉCAPSULEUR (1)

BTOP-1

VIS SANS FIN DE TRANSPORT (1)

PGC24-8

AXE DE LA VIS SANS FIN AVEC ÉCROU (1)

PG24-25

DOUILLE DE LA VIS SANS

FIN DE TRANSPORT (1)

PG24-23

MOTEUR DE LA VIS SANS FIN

DE TRANSPORT AVEC ROUE (1)

PG24-24

ROUE DE LA VIS SANS FIN DE TRANSPORT (1)

PG24-49

BOUGIE D'ALLUMAGE (1)

PG24-21

BRÛLEUR (1)

PG24-78

VIS M4.2 X 10 (4)

ROUE DE LA SOUFFLERIE (1)

PG24-27

VIS M4.2 X 10 (4)

MOTEUR DE LA SOUFFLERIE A

VEC ROUE (1)

PG24-26

SONDE À VIANDE (4)

PG24-86

VIS M4 X 10 (2)

COUVERCLE DU RÉSERVOIR (1)

PG24CL-3 (NOIR)

GRILLE DE PROTECTION DE

LA VIS SANS FIN DE TRANSPORT (1)

PG24CL-4

PLAQUE DE PROTECTION (1)

PG24CL-5

FENÊTRE DU RÉSERVOIR (1)

PG24CL-6

UNITÉ DE COMMANDE WI-FI (1)

PG24CL-7

TIGE DE NETTOYAGE

DU RÉSERVOIR (1)

PG24CL-8

de granules. La consommation de granules variera

considérablement en fonction de la température

ambiante ainsi que de la température de cuisson.

16. Il vous est recommandé de ne pas entreposer de

granules dans le réservoir pour des périodes prolongées

; ils peuvent en effet absorber l’humidité de l’air et

obstruer la vis sans ﬁn de transport.

17. Garder le couvercle fermé pendant le fonctionnement

du barbecue. Le barbecue est conçu pour une cuisson à

couvercle fermé.

18. Il convient de noter que la température de cuisson

afﬁchée sur l’écran de l’unité de commande est mesurée

près de la surface de cuisson sur le côté gauche du

barbecue. La véritable température à l’intérieur de la

chambre de cuisson variera légèrement tout au long de

la cuisson.

19. Ne pas utiliser d’accessoires dont l’utilisation n’est pas

indiquée avec cet appareil.

20. Ne jamais employer d’essence, de carburant de lanterne

de type essence, de kérosène, de produit d’allumage

pour charbon ou de liquides semblables pour démarrer

ou raviver un feu dans cet appareil. Garder tous ces

liquides à bonne distance de l’appareil pendant qu’il est

en service.

21. Les cendres doivent être déposées dans un conteneur

métallique possédant un couvercle hermétique. Le

conteneur fermé qui contient les cendres doit être placé

sur une surface non combustible ou sur le sol, très loin

de tous les matériaux combustibles jusqu’à l’élimination

déﬁnitive des cendres. Les cendres qui sont destinées à

être enterrées dans le sol ou dispersées autrement sur

place doivent être conservées dans le conteneur jusqu’à

ce qu’elles soient complètement refroidies.

22. La créosote – Formation et nécessité de la retirer.

Lors de leur lente combustion, les granules de bois

produisent du goudron et d’autres vapeurs organiques

qui, combinés à l’humidité rejetée, forment la créosote.

Les vapeurs de créosote se condensent dans les

tuyaux d’évacuation d’un four relativement froid et

dans la hotte de ventilation d’un foyer à combustion

lente. Il en résulte une accumulation de résidus de

créosote dans les tuyaux d’évacuation et la hotte de

ventilation. Une fois mise à feu, cette créosote produit

un feu extrêmement chaud. Le tuyau d’évacuation

des graisses doit être inspecté au moins toutes les 50

heures pour déterminer si une accumulation de graisse

et/ou de créosote s’est produite. Si tel est le cas, cette

accumulation doit être enlevée pour réduire le risque

d’incendie.

1. NE PAS laisser l’appareil sans surveillance lorsqu’il

fonctionne. L’utilisateur est tenu de rester à proximité du

produit et de garder celui-ci dans son champ de vision

direct pendant toute la durée de son fonctionnement.

2. Tenir les enfants et animaux domestiques à l’écart du

brûleur en permanence.

3. La consommation d’alcool ou de médicaments obtenus

ou non sur ordonnance risque de diminuer votre faculté

de monter correctement l’appareil ou de l’utiliser en toute

sécurité.

4. Destiné à un usage EN PLEIN AIR uniquement. NE PAS

utiliser à l’intérieur d’un immeuble, d’un garage ou de

tout autre endroit renfermé. NE PAS utiliser dans un

véhicule récréatif ou sur un bateau. NE JAMAIS utiliser cet

appareil comme système de chauffage.

5. Ne faire fonctionner cet appareil sous AUCUNE surface

surplombante. Conserver une distance minimale de 0,9 m

(36 pouces) entre les quatre côtés de l’appareil et TOUTE

construction. N’entreposer aucun matériau combustible

et aucun liquide inﬂammable, y compris du bois, des

plantes et herbes sèches, des buissons, du papier et des

toiles à proximité de l’appareil.

6. Ce produit n’est pas destiné à un usage commercial.

7. Toujours laisser refroidir l’appareil avant de le recouvrir

de sa housse d’extérieur.

8. Toujours recouvrir l’appareil de sa housse d’extérieur

(lorsqu’elle est fournie) lorsqu’il ne sert pas.

9. Toujours débrancher le barbecue avant de le recouvrir de

la housse d’extérieur.

10. Utiliser uniquement sur une surface stable et non

combustible comme les briques, le béton ou une surface

en terre. Ne pas utiliser cet appareil sur une surface qui

peut brûler ou fondre comme du bois, de l’asphalte, du

vinyle ou du plastique.

11. S’assurer que la zone de nettoyage du brûleur est

fermée avant d’allumer le barbecue.

12. S’assurer que le seau de collecte des graisses est monté

avant d’allumer le barbecue.

13. En cas d’incendie, débrancher le barbecue, fermer le

couvercle et le laisser fermé jusqu’à extinction du feu.

Lorsque le barbecue aura refroidi, suivre les consignes

de nettoyage avant la prochaine utilisation.

14. Utiliser uniquement des granules de feuillu à usage

alimentaire qui sont fabriqués pour être utilisés dans

des barbecues à granules. L’utilisation de granules

de conifères ou de bois de chauffage annulera votre

garantie.

15. Ne pas laisser le réservoir à granules se vider

complètement. Les granules peuvent être ajoutés à

tout moment. Le réservoir peut contenir environ 10 kg

DANGER

Ne pas effectuer de travaux sur le barbecue lorsque

celui-ci est branché. L’électrocution qui risquerait de se

produire peut entraîner le décès ou des blessures graves.

CONSIGNES DE MONTAGE

Retirer toutes les pièces détachées se trouvant à l’intérieur

du barbecue et du réservoir. Déposer une couverture ou un

morceau de carton par terre pour protéger le barbecue.

MONTAGE DES PIEDS

Avec l’aide d’une autre personne, mettre le barbecue à

l’envers sur la couverture ou le carton. Les couvercles du

barbecue et du réservoir s’ouvriront lors de cette opération.

Veiller à ne pas les abîmer. Le barbecue risque également

de rouler sur son couvercle. Une personne devrait donc le

maintenir en place pendant que l’autre personne monte les

pieds ﬁxes et les roues.

1. Coucher le barbecue sur le côté arrière.

2. Monter chacun des 4 pieds comme indiqué à la Fig.

1. S’assurer que les pieds équipés de roulettes sont

attachés du côté droit du barbecue, les roulettes se

trouvant vers l’extérieur. Remarque : les pieds avant

portent la lettre F et les pieds arrière, la lettre B.

3. Remettre le barbecue à l’endroit.

4. Serrer toute la quincaillerie.

FIG. 1

BOULON M8 X 20

ÉCROU À BRIDE M8

MONTAGE DU PLATEAU DU BAS

1. Monter le plateau du bas, comme indiqué à la Fig. 2 en

attachant la quincaillerie aux quatre coins.

2. Serrer la quincaillerie.

VIS M6 X 15

CHEMINEE JOINT

ECROU M6

BOULON M6 X 76

BOULON M8 X 60

ÉCROU À EMBASE M8 (4)

FIG. 2

MONTAGE DE LA CHEMINÉE ET DE SON CHAPEAU

1. Monter la cheminée sur le barbecue comme indiqué à

la Fig. 3. S’assurer que le joint de la cheminée est placé

entre le barbecue et la cheminée.

2. Serrer toute la quincaillerie.

3. Placer le boulon M6 x 76 à travers le chapeau de la

cheminée et l’attacher au moyen d’un (1) écrou M6.

Visser le second écrou sur le boulon en laissant environ

3,8 cm à partir de l’extrémité supérieure du chapeau.

Visser l’ensemble du chapeau vers le bas dans le support

de la cheminée jusqu’à ce que l’écrou du bas touche le

support. Voir la Fig. 3.

VIS M6 X 15

CHEMINEE JOINT

ECROU M6

BOULON M6 X 76

BOULON M8 X 60

ÉCROU À EMBASE M8 (4)

FIG. 3

4. Il est possible d’ajuster la hauteur du chapeau de la

cheminée en fonction de l’été et de l’hiver. L’écart doit

être d’environ 3,8 cm en été, et d’environ 1,3 cm en hiver.

5. Serrer toute la quincaillerie.

MONTAGE DE LA POIGNÉE

1. Monter la poignée comme indiqué à la Fig. 4.

2. Serrer toute la quincaillerie.

VIS DE POIGNÉE M6 (2)

POIGNÉE DU DÉFLECTEUR

POIGNÉE

POIGNÉE DE LUNETTE (2)

M6 X 15 SCREW

GREASE BUCKET

ASH CUP

FIG. 4

MONTAGE DE LA POIGNÉE DU RÉSERVOIR

1. Monter la poignée du réservoir comme indiqué à la Fig. 5.

FIG. 5

MONTAGE DE LA GRILLE DE SÉCURITÉ ET DU COUVERCLE

DU RÉSERVOIR

1. Monter la grille et le couvercle comme indiqué à la Fig. 6.

La languette du réservoir doit être insérée dans la fente

de la grille. Attacher la grille et le couvercle au réservoir

avec des vis.

VIS M4 X 10 (2)

COUVERCLE DE TRÉMIE (1)

GARDE DE TRÉMIE (1)

FIG. 6

MONTAGE DU SUPPORT D’ÉTAGÈRE

1. Monter le support comme indiqué à la Fig. 7.

2. Serrer toute la quincaillerie.

M6 X 15 SCREW (4)

M6 FLANGE NUT (4)

UPPER GRATE BKT (2)

PG24SG-11

FIG. 7

INSTALLER L’ÉTAGÈRE

(Facultatif-Ne pas installer si vous installez une boîte à

garniture)

1. Installer l’étagère comme illustré à la Fig 8.

2. Serrez tous les accessoires

M6 HANDLE SCREW (2)

HANDLE DEFLECTOR

HANDLE

HANDLE BEZEL (2)

GREASE BUCKET

M6 X 15 VIS

ASH CUP

FIG. 8

SEAU DE COLLECTE DES GRAISSES

1. Suspendre le seau de collecte des graisses à son conduit

d’évacuation comme indiqué à la Fig. 9.

RÉCIPIENT À CENDRES

1. Monter le récipient à cendres comme indiqué à la Fig. 9.

Ne jamais utiliser le barbecue sans y monter le récipient

à cendres.

RÉCIPIENT

À CENDRES

SEAU DE COLLECTE

DES GRAISSES

FIG. 9

MONTAGE DE LA LÈCHEFRITE

1. Monter la lèchefrite comme indiqué aux Fig. 10 et 11.

DRIP TRAY

FIG. 10

DRIP TRAY

FIG. 11

GRILLE DE CONSERVATION AU CHAUD ET GRILLE DE

CUISSON

1. Monter la grille de cuisson comme indiqué à la Fig. 12.

UPPER GRATE (2)

PG24SG-5

LOWER GRATE (2)

PG24-70

FIG. 12

INSTRUCTIONS DE MONTAGE DU BOUTON DE NETTOYAGE

Serrer à la main le bouton de nettoyage du brûleur comme

indiqué à la Fig. 13.

FIG. 13

PG24-9 (1)

NETTOYEZ BOUTON DE PORT

BOUTON DE LA TIGE DE LA ZONE DE NETTOYAGE

1. Le bouton de la tige de la zone de nettoyage doit être

enfoncé lorsque le barbecue est allumé. S’assurer que

le système de blocage de la tige est tiré vers le bas et

bloque le bouton aﬁn d’empêcher l’ouverture de la zone

de nettoyage par inadvertance. Voir Fig. 14

2. Soulever le système de blocage de la tige et tirer le

bouton de la tige de nettoyage pour vider les cendres

dans le récipient prévu à cet effet. Voir la Fig. 15.

3. Voir les consignes concernant le nettoyage du brûleur.

WARMING RACK

COOKING GRATE

NETTOYEZ BOUTON DE PORT

FIG. 14

WARMING RACK

COOKING GRATE

NETTOYEZ BOUTON DE PORT

FIG. 15

MONTAGE DU BOUTON DE NETTOYAGE DU RÉSERVOIR

Attacher le bouton de nettoyage du réservoir à la main

comme illustré à la Fig. 16.

PG24-9 (1)

PULLOUT KNOB

FIG. 16

NETTOYAGE DU BRÛLEUR

Avant chaque utilisation, il convient de nettoyer le brûleur

en soulevant le système de blocage de la tige de la zone de

nettoyage et en tirant le bouton de celle-ci du côté droit du

barbecue pour ouvrir la zone de nettoyage du brûleur. Les

cendres provenant de l’utilisation précédente tomberont

ainsi dans le récipient prévu à cet effet qui se trouve

en dessous du barbecue. Il convient d’enlever ensuite

le récipient, de le vider et de le remonter avant chaque

utilisation.

DANGER

Ne jamais faire fonctionner le barbecue à granules sans

que le récipient à cendres ne soit monté.

S’assurer que le trou de la zone de nettoyage du brûleur est

fermé et bloqué avant d’allumer le barbecue.

WARMING RACK

COOKING GRATE

CLEANOUT PORT CLOSED

CLEANOUT PORT OPEN

Ne jamais ouvrir le trou de la zone de nettoyage du brûleur

lorsque le barbecue est chaud.

La page charge ...

Camp Chef PG24CL Warning & Instruction Booklet

Marque: Camp Chef

Modèle: PG24CL

Catégorie: Barbecues

Taper: Warning & Instruction Booklet

Ce manuel convient également à

PG36CL

Télécharger le PDF

rapport

dans d''autres langues

English: Camp Chef PG24CL

Camp Chef PG24CL Warning & Instruction Booklet

Ce manuel convient également à

Camp Chef PG24CL Warning & Instruction Booklet

dans d''autres langues

Documents connexes

Autres documents