Wacker Neuson BFS 914B Manuel utilisateur

Operator’s Manual

Floor Saw

BFS 914B

Notice d’Emploi

Découpeur de joints

5200007033 06 0811

EN - FR

5200007033

Manufacturer

Wacker Neuson Produktion GmbH & Co. KG

Preußenstraße 41

80809 München

www.wackerneuson.com

Tel.: +49-(0)89-354 02-0

Fax: +49-(0)89-354 02-390

Translation of the original operator's manual in German

0212750en 006

08.2011

1

1 Foreword ....................................................................................................................2

2 Introduction ............................................................................................................... 3

2.1 Means of representation for this operator's manual ........................................... 3

2.2 Wacker Neuson representative .......................................................................... 4

2.3 Described machine types ................................................................................... 4

2.4 Identification of the machine............................................................................... 5

3 Safety ......................................................................................................................... 6

3.1 Principle.............................................................................................................. 6

3.2 Qualification of the operating personnel............................................................. 9

3.3 Protective gear ................................................................................................. 10

3.4 Transport .......................................................................................................... 11

3.5 Operating safety ............................................................................................... 12

3.6 Safety during the operation of combustion engines ......................................... 15

3.7 Safety during floor saw operation..................................................................... 17

3.8 Maintenance..................................................................................................... 19

3.9 Safety devices .................................................................................................. 21

4 Safety and information labels ................................................................................22

5 Technical data ......................................................................................................... 24

1 Troubleshooting ...................................................................................................... 50

2 Emission control systems information and warranty ......................................... 51

3 Glossary ................................................................................................................... 52

3.1 Use of oxygenated fuels................................................................................... 52

Contents

1 Foreword

2

1Foreword

This operator's manual contains information and procedures for the safe opera-

tion and maintenance of your Wacker Neuson machine. In the interest of your

own safety and to prevent accidents, you should carefully read through the safety

information, familiarize yourself with it and observe it at all times.

This operator's manual is not a manual for extensive maintenance and repair

work. Such work should be carried out by Wacker Neuson service or authorized

specialists.

The safety of the operator was one of the most important aspects taken into con-

sideration when this machine was designed. Nevertheless, improper use or in-

correct maintenance can pose a risk. Please operate and maintain your Wacker

Neuson machine in accordance with the instructions in this operator's manual.

Your reward will be troublefree operation and a high degree of availability.

Defective machine parts must be replaced immediately!

Please contact your Wacker Neuson representative if you have any questions

concerning operation or maintenance.

No part of this publication may be reproduced in any form or by any means, elec-

tronic or mechanical, including photocopying, without the expressed written per-

mission of Wacker Neuson.

Any type of reproduction, distribution or storage on data media of any type and

form not authorized by Wacker Neuson represents an infringement of copyright

and will be prosecuted.

We expressly reserve the right to make technical modifications – even without

special notice – which aim at further improving our machines or their safety stan-

dards.

2 Introduction

3

2 Introduction

2.1 Means of representation for this operator's manual

Warning symbols

This operator's manual contains safety information of the categories:

DANGER, WARNING, CAUTION, NOTICE.

They should be followed to prevent danger to life and limb of the operator or dam-

age to equipment and exclude improper service.

Notes

Note: Complementary information will be displayed here.

DANGER

This warning notice indicates immediate hazards that result in serious injury or

even death.

f Danger can be avoided by the following the actions mentioned.

WARNING

This warning notice indicates possible hazards that can result in serious injury

or even death.

f Danger can be avoided by the following the actions mentioned.

CAUTION

This warning notice indicates possible hazards that can result in minor injury.

f Danger can be avoided by the following the actions mentioned.

NOTICE

This warning notice indicates possible hazards that can result in material dam-

age.

f Danger can be avoided by the following the actions mentioned.

2 Introduction

4

Instructions

f This symbol indicates there is something for you to do.

1. Numbered instructions indicate that you have to carry out something in a defined

sequence.

 This symbol is used for lists.

2.2 Wacker Neuson representative

Depending on your country, your Wacker Neuson representative is your Wacker

Neuson service, your Wacker Neuson affiliate or your Wacker Neuson dealer.

You can find the addresses in the Internet at www.wackerneuson.com.

The address of the manufacturer is located at the beginning of this operator's

manual.

2.3 Described machine types

This operator's manual is valid for different machine types from a product range.

Therefore some figures can differ from the actual appearance of your machine.

It is also possible that the descriptions include components which are not a part

of your machine.

Details for the described machine types can be found in the chapter Technical

data.

2 Introduction

5

2.4 Identification of the machine

Nameplate data

The nameplate lists information that uniquely identifies your machine. This infor-

mation is needed to order spare parts and when requesting additional technical

information.

f Enter the information of your machine into the following table:

Item Designation Your information

1 Group and type

2 Construction year

3 Machine no.

4 Version no.

5 Item no.

3 Safety

6

3Safety

3.1 Principle

State of the art

This machine has been constructed with state-of-the-art technology according to

the recognized rules of safety. Nevertheless, when used improperly, dangers to

the life and limb of the operator or to third persons or damage to the machine or

other materials cannot be excluded.

State of the art

This machine has been constructed with state-of-the-art technology according to

the recognized rules of safety. Nevertheless, when used improperly, dangers to

the life and limb of the operator or to third persons or damage to the machine or

other materials cannot be excluded.

Proper use

The machine must only be used for the following purposes:

 Cutting expansion joints in concrete, asphalt and screed.

 Cutting out damaged areas of concrete and asphalt.

 Straightening blacktops and concrete surfaces.

 Sawing off precast concrete parts.

The machine may only be used with cutting blades that are intended for use with

the machine and the material to be cut.

The machine may not be used for the following purposes:

 Cutting wood.

 Cutting plastics.

 Cutting materials that contain asbestos.

The machine may not be operated with blades, knives, brushes, etc.

Its proper use also includes the observance of all instructions contained in this

operator's manual as well as complying with the required service and

maintenance instructions.

Any other use is regarded as improper. Any damage resulting from improper use

will void the warranty and the liability on behalf of the manufacturer. The operator

assumes full responsibility.

3 Safety

7

Structural modifications

Never attempt to modify the machine without the written permission of the

manufacturer. To do so will endanger your safety and the safety of other people!

In addition, this will void the warranty and the liability on behalf of the

manufacturer.

Especially the following are cases of structural modifications:

 Opening the machine and the permanent removal of components from

Wacker Neuson.

 Installing new components which are not from Wacker Neuson and not

equivalent to the original parts in design and quality.

 Installation of accessories which are not from Wacker Neuson.

It is no problem to install spare parts from Wacker Neuson.

It is no problem to install accessories that are available in the Wacker Neuson

product range of your machine. Please refer to the installation regulations in this

operator's manual.

Requirements for operation

The ability to operate the machine safely requires:

 Proper transport, storage and setup.

 Careful operation.

 Careful service and maintenance.

Operation

Operate the machine only as intended and only when in proper working

condition.

Operate the machine in a safety-conscious manner with all safety devices

attached and enabled. Do not modify or disable any safety devices.

Before starting operation, check that all control and safety devices are

functioning properly.

Never operate the machine in a potentially explosive environment.

Supervision

Never leave the machine running unattended!

Maintenance

Regular maintenance work is required in order for the machine to operate

properly and reliably over time. Failure to perform adequate maintenance

reduces the safety of the machine.

 Strictly observe the prescribed maintenance intervals.

 Do not use the machine if it requires maintenance or repairs.

3 Safety

8

Malfunctions

If you detect a malfunction, you must shut down and secure the machine

immediately.

Eliminate the malfunctions that impair safety immediately!

Have damaged or defective components replaced immediately!

For further information, refer to chapter Troubleshooting.

Spare parts, accessories

Use only spare parts from Wacker Neuson or such that are equivalent to the

original parts in design and quality.

Only use accessories from Wacker Neuson.

Non-compliance will exempt the manufacturer from all liability.

Exclusion of liability

Wacker Neuson will refuse to accept liability for injuries to persons or for damage

to materials in the following cases:

 Structural modifications.

 Improper use.

 Failure to comply with this operator's manual.

 Improper handling.

 Using of spare parts which are not from Wacker Neuson and not equivalent

to the original parts in design and quality.

 Using of accessories which are not from Wacker Neuson.

Operator's manual

Always keep the operator's manual near the machine or near the worksite for

quick reference.

If you have misplaced the operator's manual or require an additional copy,

contact your Wacker Neuson representative or download the operator's manual

from the Internet (www.wackerneuson.com).

Always hand over this operator's manual to other operators or to the future owner

of the machine.

Country-specific regulations

Observe the country-specific regulations, standards and guidelines in reference

to accident prevention and environmental safety, for example those pertaining to

hazardous materials and wearing protective gear.

Complement the operator's manual with additional instructions taking into

account the operational, regulatory, national or generally applicable safety

guidelines.

3 Safety

9

Operator's controls

Always keep the operator's controls of the machine dry, clean and free of oil or

grease.

Operating elements such as ON/OFF switch, throttle levers etc. may not be

locked, manipulated or changed without authorization.

Checking for signs of damage

Inspect the machine when it is switched off for any signs of damage at least once

per work shift.

Do not operate the machine if there is visible damage or defects.

Have any damage or defects eliminated immediately.

3.2 Qualification of the operating personnel

Operator qualifications

Only trained personnel are permitted to start and operate the machine. The

following rules also apply:

 You are at least 18 years of age.

 You are physically and mentally fit.

 You have received instruction on how to independently operate the machine.

 You have received instruction in the proper use of the machine.

 You are familiar with required safety devices.

 You are authorized to start machines and systems in accordance with the

standards governing safety.

 Your company or the operator has assigned you to work independently with

this machine.

Incorrect operation

Incorrect operation or misuse by untrained personnel can endanger the health

and safety of the operator or third persons and also cause machine and material

damage.

Operating company responsibilities

The operating company must make the operator's manual available to the

operator and ensure that the operator has read and understood it.

3 Safety

10

Work recommendations

Please observe the recommendations below:

 Work only if you are in a good physical condition.

 Work attentively, particularly as you finish.

 Do not operate the machine when you are tired.

 Carry out all work calmly, circumspectly and carefully.

 Never operate the machine under the influence of alcohol, drugs or

medication. This can impair your vision, reactions and your judgment.

 Work in a manner that does not endanger others.

Ensure that no persons or animals are within the danger zone.

3.3 Protective gear

Work clothing

Clothing should be appropriate, i.e. should be close-fitting but not restrict your

movement.

When on construction sites, do not wear long hair loosely, loose clothing or je-

welry including rings. These objects can easily get caught or be drawn in by mo-

ving machine parts.

Only wear clothing made of material that is not easily flammable.

Personal protective gear

Wear personal protective gear to avoid injuries or health hazards:

 Non-skid, hard-toed shoes.

 Work gloves made of durable material.

 Overalls made of durable material.

 Hard hat.

 Ear protection.

 Face protection.

 Eye protection.

 Breathing protection in the case of dusty ambient air.

Ear protection

This machine generates noise that exceeds the country-specific permissible noi-

se levels (individual rating level). It may therefore be necessary to wear ear pro-

tection. You can find the exact value in the chapter Technical Data.

When wearing ear protection while working, you must pay attention and exercise

caution because your hearing is limited, e.g. in case someone screams or a sig-

nal tone sounds.

Wacker Neuson recommends that you always wear ear protection.

3 Safety

11

Breathing protection

If a lot of dust is produced when cutting, always wear suitable breathing protec-

tion.

Use the water supply.

Provision of fire extinguishers

Ensure that a fire extinguisher is always to hand on the worksite.

Do not exceed the daily usage limit

The machine generates noise.

Observe the regulations which apply in your country and guidelines concerning

the maximum daily service life of the machine.

Always wear the prescribed safety clothing.

Information about the noise levels produced by the machine can be found in the

Technical Data chapter.

3.4 Transport

Switching off the machine

Before you transport the machine, it must be switched off, and the engine must

be given sufficient time to cool down.

Emptying the tank

Wacker Neuson recommends emptying the fuel tank before transport. Fuel could

run out, e.g. if the machine is tilted.

Observe the national safety guidelines and the hazardous materials regulations

that apply to the respective means of transportation.

Lifting

When lifting the machine, observe the following instructions:

 Designate a skilled person to guide you for the lifting procedure.

 You must be able to see or hear this person.

 Use only suitable and certified hoisting gear, lifting tackle and load-bearing

equipment with sufficient lifting capacities.

 Only use the attachment points described in the operator's manual.

 Attach the machine securely to the hoisting gear.

 Ensure that no one is nearby or under the machine.

 Do not climb onto the machine.

 Check the lifting strap on the machine for wear and damage.

 Before lifting, secure (loose) components with the relevant devices.

 Remove (loose) components before lifting.

 Remove the tool before lifting.

3 Safety

12

Loading the machine

Loading ramps must be able to bear the load and be in a stable position.

Make sure that no one can be endangered if the machine slips away or tips over

or if machine parts suddenly move upward or downward.

Put the operating controls and moving parts in their transport position.

Secure the machine with load-securing straps so that it cannot tip over, fall down

or slide away. Only use the attachment points described in the operator's manu-

al.

Transport vehicle

Use only suitable transport vehicles with sufficient load-carrying capacity and

suitable tie-down lugs.

Transporting the machine

Secure the machine on the transport device against tilting, falling or slipping.

Only use the lashing points listed in the operating instructions.

Also observe the country-specific regulations, standards and guidelines.

Restarting

Machines, machine parts, accessories or tools that were detached for transport

purposes must be re-mounted and fastened before restarting.

Only operate in accordance with the operating instructions.

3.5 Operating safety

Explosible environment

Never operate the machine in a potentially explosive environment.

Work environment

Familiarize yourself with your work environment before you start work. This in-

cludes e.g. the following items:

 Obstacles in the work and traffic area.

 Load-bearing capacity of the ground.

 The measures needed to cordon off the construction site from public traffic in

particular.

 The measures needed to secure walls and ceilings.

 Options available in the event of an accident.

3 Safety

13

Safety in the work area

When working with the machine especially pay attention to the following points:

 Electric lines or pipes in work area.

 Gas lines or water lines in the work area.

 Material becoming separated, dropping down or ejected. Make sure that you

do not put other persons in danger.

 Pay maximum attention in the vicinity of drops or slopes. Risk of falling.

 Maintain a sufficient distance from flammable materials.

Checks before starting work

Check the following points before beginning work:

 Condition of cutting blade.

 Safety devices.

 Switch and current-carrying lines for damage and corrosion.

 Tightness of the cutting blade.

 Machine settings.

Starting the machine

Observe the safety information and warning notices located on the machine and

in the operator's manual.

Never attempt to start a machine that requires maintenance or repairs.

Start the machine as described in the operator's manual.

Vertical stability

Always ensure that the machine is vertically stable and cannot tip over, roll or

slide away.

Proper operator position

Do not leave the proper operator position while operating the machine.

The intended operator position is at the controls behind the machine.

Caution with hot parts

Do not touch the machine during or shortly after operation. Some parts can be-

come very hot and can cause severe burns.

Caution with movable parts

Keep your hands, feet and loose clothing away from moving or rotating machine

parts. Parts of your body being pulled in or crushed can cause serious injuries.

3 Safety

14

Caution with toxic materials

Some materials may contain toxic chemicals which are released during demoli-

tion. Therefore personal protective equipment must be worn to prevent inhalation

of and skin contact with work dust.

No persons endangered

Be sure that no persons are endangered by flying or falling materials. Always

work very attentively, and anticipate potential hazards.

Make sure that people in the vicinity are at a sufficient distance from the machi-

ne.

Do not use any starter sprays

Highly flammable starter sprays pose a fire hazard.

Do not use any starter sprays.

Starter sprays are highly flammable and can cause backfiring and engine dama-

ge.

Switching off the machine

Switch off the engine in the following situations:

 Before breaks.

 If you are not using the machine.

Store the machine in such a way that it cannot tilt, fall or slip.

Storage

Store the machine securely so that it cannot tilt, fall or slip.

Storage location

After operation, allow the machine to cool and then store it in a sealed-off, clean

and dry location protected against frost and inaccessible to children.

Vibrations

When manually operated machines are intensively used, long-term damage

caused by vibrations cannot be precluded.

Observe the relevant legal instructions and guidelines to minimize vibration

stress.

Details on vibration stress associated with the machine can be found in the chap-

ter Technical Data.

3 Safety

15

3.6 Safety during the operation of combustion engines

Checking for signs of damage

Check the engine while switched off for leaks and cracks in the fuel line, tank and

fuel cap at least once per work shift.

Do not operate the machine if there is visible damage or defects.

Have any damage or defects eliminated immediately.

Dangers during operation

Combustion engines can be dangerous, particularly during operation and when

refueling.

Read and follow all safety instructions. Otherwise there is a risk of personal injury

and/or damage to property!

Do not start the engine near spilt fuel or if you smell fuel – this may cause an ex-

plosion!

 Remove the machine from such areas.

 Remove the spilt fuel immediately!

Do not change the engine speed

Do not change the preset engine speed, as this may cause engine damage.

You may only change the idle speed. The idle speed must be set such that the

cutting blade does not rotate while the engine is idling.

Preventing fires

Open flames and smoking are strictly prohibited in the immediate vicinity of the

machine.

Make sure that waste, such as paper, dry leaves or grass do not accumulate

around the exhaust muffler. The waste materials may ignite.

3 Safety

16

Safety precautions when refueling

Please observe the following safety-relevant instructions when refueling:

 Do not refuel near open flames.

 Do not smoke.

 Turn off the engine before refueling and allow it to cool down.

 Refuel in a well-ventilated environment.

 Wear fuel-proof protective gloves and, if there is the possibility of spraying,

protective goggles and clothing.

 Do not inhale fuel vapors.

 Avoid skin and eye contact with fuel.

 For refueling, use clean tools such as a hopper.

 Do not spill fuel, especially onto hot parts.

 Remove any spilt fuel immediately.

 Use the correct fuel grade.

 Do not mix fuel with other liquids.

 Fill the tank only up to the maximum marking. If there is no maximum mar-

king, do not fill up the tank completely.

 Lock the fuel cap securely after refueling.

Operation in closed rooms

In closed or partially closed rooms such as tunnels, drifts or deep trenches, ensu-

re sufficient ventilation and extraction by, for example, providing a powerful ex-

haust air fan.

Danger of poisoning! Do not inhale exhaust fumes. They contain toxic carbon

monoxide that can lead to unconsciousness or death.

Caution with hot parts

Do not touch any hot parts such as the engine block or exhaust muffler during

operation or directly afterwards. These parts can become very hot and cause se-

vere burns.

Shutting off the fuel tap

When the machine stops, shut off the fuel tap.

Cleaning the engine

Clean the engine when it is cool to remove any dirt.

Do not use gasoline or solvents. Danger of explosion!

Health hazard due to exhaust fumes

Warning

The engine's exhaust fumes contain chemicals which are known to the State of

California to cause cancer, congenital defects or other reproductive anomalies.

3 Safety

17

Notes on the EPA engine

Caution

This machine is equipped with an EPA-certified engine.

Modifying the engine speed influences the EPA certification and emission. The

engine may only be set by a skilled technician.

For more detailed information, contact your nearest engine or Wacker Neuson

representative.

3.7 Safety during floor saw operation

Belt guard

Never operate the machine without a belt guard!

Exposed belts and belt pulleys are dangerous and can cause serious injuries if

they pull in any part of your body or if parts are ejected.

Danger of falling over

Operate the machine so that it cannot tip over or fall down from bordered areas,

edges and steps.

Cutting blade guard

Never operate the machine without a cutting blade guard.

The cutting blade guard performs the following functions:

 Protects the operator from the rotating cutting blade.

 Diverts workpiece particles and sparks or chips from a damaged cutting bla-

de away from the operator.

Only operate the machine when the cutting blade guard is folded down.

Make sure that the cutting blade guard and its limit stops are not damaged or

worn.

Wet-cutting

Use a water sprayer when dust formation is excessive, e.g. when cutting conc-

rete or stone.

Only use cutting blades that are suitable for wet cutting.

Before ending the wet cutting process, allow the cutting blade to run without the

water sprayer until it is dry.

Not exceeding the maximum tilt position

 Do not exceed the maximum tilt position (see the description in the Maximum

permissible tilt chapter).

 Only operate the machine at maximum tilt for short periods of time.

If you exceed the maximum tilt, the engine lubrication system will fail and thus

inevitably damage important engine parts.

3 Safety

18

Notes regarding work methods

 Fold down the protective hood fully. The protective hood can catch material

flung away from the work area and divert it away from the operator.

 Particularly when starting the engine you have to make sure that the cutting

blade does not come into contact with anything.

 Always operate the machine at full throttle even when first placing it into the

cut.

 When first placing the the cutting blade into the cut, set it slowly onto the ma-

terial. Excessive pressure can damage the cutting blade.

 Move the machine in a straight line together with the cutting blade. Pressure

from the side can damage the cutting blade.

 Avoid cutting tight curves.

 On sloping carriageways and surfaces, pressure must not be applied to the

side of the blade.

 Never exceed the maximum speed (printed on cutting blade).

Removing foreign objects before cutting

Before cutting, remove foreign objects such as nails, etc. from the cutting area.

Cutting various materials

 Do not process loose materials (e.g. paving stones).

 Do not cut into the gravel area using diamond-edged cutting blades.

 When cutting on the edge of the track or when cutting two different materials

(cutting in the joint area), uneven wear is possible.

Do not touch a rotating cutting blade

Never touch a rotating cutting blade with your hand or any other body part.

Danger of severe injury.

Pay attention and exercise caution when working with ear protection

When wearing ear protection you must pay attention and exercise caution be-

cause your hearing is limited, e.g. in case someone screams or a signal tone

sounds.

Danger of fire due to sparks

Danger of fire due to hot workpiece particles flung away from the work area.

 Do not work near flammable materials.

 Only wear clothing made of material that is not easily flammable.

La page charge ...

Wacker Neuson BFS 914B Manuel utilisateur

Wacker Neuson BFS 914B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents