Yard Pro Y160Y21R Le manuel du propriétaire

OPERATOR'S MANUAL

SELF-PROPELLED ROTARY

LAWN MOWER

Assembly

• Operation

• Maintenance

° Service and Adjustments

° Storage

• Troubleshooting

&WARNING: This lawn mower is equipped with an internal combustion engine and

should not be used on or near any unimproved forest-covered, brush-covered or

grass-covered land unless the engine's exhaust system is equipped with a spark

arrester meeting applicable local or state laws (if any). tf a spark arrester is used, it

should be maintained in effective working order by the operator.

In the state of California the above is required by law (Section 4442 of the California

Public Resources Code). Other states may have similar taws. Federal laws apply

on federaI lands. A spark arrester for the muffler is available through your nearest

authorized service center.

193733 Rev. 9 09.16.10 BY Printed in U.S.A.

Safety Rules ................. 2-3 Maintenance ............. 22-26 Storage ..................... 33-34

Assembiy ...................... 5-8 Service and Troubleshooting ........ 35-36

Operation .................... 9-2t Adjustments .............. 27-32

IMPORTANT: This cutting machine iscapable of amputating hands and feet andthrowingob-

jects. Failure to observe the following safety instructions could result in serious injury or death.

,&Look for this symbol to point out impor- • Do not pull mower backwards unless

tant safety precautions. It means

CAUTION!!! BECOME ALERT!t!

YOUR SAFETY IS INVOLVED.

&WARNING: Inordertopreventaccidental •

starting when setting up, transporting, ad-

lusting or making repairs, always disconnect

sparkplug wire and place wire where it cannot

come in contact with plug.

•,WARNING: Engine exhaust, some of its •

constituents, and certain vehicle compo-

nents contain or emit chemicals known to

the State of California to cause cancer and °

birth defects or other reproductive harm.

•(kWARNING: Battery pests, terminals and

related accessories contain lead and lead

compounds, chemicals known to the State •

of California to cause cancer and birth

defects or other reproductive harm. Wash •

hands after handling.

=6,CAUTION: Muffler and

other engine parts become •

extremely hot during

operation and remain hot

after engine has stopped. °

To avoid severe burns on °

contact, stay away from these areas.

!. GENERAL OPERATION

, Read, understand, and follow all

instructions on the machine and in the

manual(s) before starting. Be thoroughly

familiar with the controls and the proper

use of the machine before starting,

° Do not put hands or feet near or under

rotating parts. Keep clear of the dis-

charge opening at all times.

• Only allow responsible individuals, who

are familiar with the instructions, to oper-

ate the machine.

• Clear the area of objects such as rocks,

toys, wire, bones, sticks, etc., which

could be picked up and thrown by blade.

• Be sure the area is clear of other people

before mowing. Stop machine if anyone

enters the area.

° Do not operate the mower when bare-

foot or wearing open sandals. Always

wear substantial foot wear.

absolutely necessary'. Always look down

and behind before and while moving

backwards.

Never direct discharged material toward

anyone. Avoid discharging material against

a wail or obstruction. Material may richo-

chet back toward the operator. Stop the

blade when crossing gravel surfaces.

Do not operate the mower without

proper guards, plates, grass catcher or

other safety protective devices in place.

See manufacturer's instructions for

proper operation and installation of

accessories, Only use accessories ap-

proved by the manufacturer.

Stop the blade(s) when crossing gravel

drives, walks, or roads.

Stop the engine (motor) whenever you

leave the equipment, before cleaning the

mower or unclogging the chute.

Shut the engine (motor) off and walt until

the blade comes to complete stop before

removing grass catcher.

Mow only in daylight / good artificial light.

Do not operate the machine while under

the influence of alcohol or drugs.

° Never operate machine in wet grass.

Always be sure of your footing: keep a

firm hold on the handle; walk, never run.

• Disengage the self-propelled mech-

anism or drive clutch on mowers so

equipped before starting the engine.

• If the equipment should start to vibrate

abnormally, stop the engine (motor) and

check immediately for the cause. Vibra-

tion is generally a warning of trouble.

• Always wear safety goggles or safety glass-

es with side shields when operating mower.

tl, SLOPE OPERATION

Slopes are a major factor related to slip &

fall accidents which can result in severe in-

jury. Aft slopes require extra caution, if you

feel uneasy on a slope, do not mow it.

DO:

• Mow across the face of slopes: never

up and down, Exercise extreme caution

when changing direction on slopes.

• Removeobstacles(rocks,treelimbs,etc.)

- Watchforholes,ruts,orbumps.Tall

grasscanhideobstacles.

DONOT:

• Donottrimneardrop-offs,ditchesor

embankments.Theoperatorcouldlose

footingorbalance.

• Donottrimexcessivelysteepslopes.

• Donotmowonwetgrass.Reducedfoot-

ingcouldcauseslipping.

I!!.CHILDREN

Tragicaccidentscanoccuriftheoperatoris

notalerttothepresenceofchildren.Children

areoftenattractedtothemachineandthe

mowingactivity.Never assume that children

will remain where you last saw them.

• Keep children out of the trimming area

and under the watchful care of another

responsible adult.

° Be alert and turn machine off if children

enter the area.

• Before and while walking backwards,

look behind and down for small children.

• Never allow chitdren to operate the mower.

• Use extra care when approaching blind

corners, shrubs, trees, or other objects

that may obscure vision.

IV, SAFE HANDLING OF GASOLINE

Use extreme care in handling gasoline.

Gasoline is extremely flammable and the

vapors are explosive.

• Extinguish all cigarettes, cigars, pipes

and other sources of ignition.

• Use only an approved container.

• Never remove gas cap or add fuel with

the engine running. Allow engine to cool

before refueling.

• Never refuel the machine indoors.

• Never store the machine or fuel contain-

er where there is an open flame, spark

or pilot light such as a water heater or on

other appliances.

• Never fill containers inside a vehicle, on

a truck or trailer bed with a plastic liner,

Always place containers on the ground

away from your vehicle before filling.

• Remove gas-powered equipment from the

truck or trailerand refuel iton the ground, if

this is not possible, then refuel such equip-

ment with a portable container, rather than

from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim

of the fuel tank or container opening at

all times until fueling is complete. Do not

use a nozzle lock-open device.

• tf fuel is spilled on clothing, change

clothing immediately.

• Never overfill fuel tank. Replace gas cap

and tighten securely.

V, GENERAL SERVICE

• Never run machine inside a closed area.

• Never make adjustments or repairs with

the engine (motor) running. Disconnect the

spark plug wire, and keep the wire away

from the plug to preventaccidentaI starting.

• Keep nuts and bolts, especially blade

attachment bolts, tight and keep equip-

ment in good condition.

• Never tamper with safety devices. Check

their proper operation regularly.

• Keep machine free of grass, leaves, orother

debris build-up, Clean oil or fuel spillage.

Allow machine to cool before storing.

• Stop and inspect the equipment if you

strike an object. Repair, if necessary,

before restarting.

• Never attempt to make wheel height

adjustments while the engine is running.

• Grass catchercomponents are subject to

wear, damage, and deterioration, which

could expose moving parts or allow objects

to bethrown. Frequentlycheck components

and replace with manufacturer's recom-

mended parts, when necessary.

, Mower blades are sharp and can cut.

Wrap the blade(s) or wear gloves, and

use extra caution when servicing them.

• Do not change the engine governor set-

ting or overspeed the engine.

, Maintain or replace safety and instruc-

tion labels, as necessary.

CONGRATU LATIONS onyour purchase of a new Lawn Mower. It has been designed, engi-

neered and manufactured to give you the best possible dependability and performance,

Should you experience any problems you cannot easily remedy, please contact your

nearest authorized service center. They have competent, well trained technicians and

the proper tools to service or repair this unit.

° Read the SAFETY RULES and this Operator's Manual in its entirety before you at-

tempt to assemble or operate your new lawn mower to insure proper operation and to

prevent injury to yourse]fand others. Save this manual for future reference,

• Your new lawn mower has been assembled at the factory with the exception of those

parts left unassembled for shipping purposes. To ensure safe and properoperation

of your lawn mower, all parts and hardware you assemble must be tightened securely.

Use the correct tools as necessary to ensure proper tightness.

° All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have

been placed in the parts bag. 3

TO REMOVE LAWN MOWER

FROM CARTON

• Remove all loose parts from carton.

• Remove lawn mower housing with care.

Avoid touching blade under housing.

Always wear gloves or other protection

when working under or lifting mower.

THINGS TO KNOW BEFORE YOU

ASSEMBLE OR OPERATE YOUR

LAWN MOWER

Do I have a side or rear discharge lawn

mower?

Look for the grass discharge opening on

your mower, if the opening is on the right

side of the mower housing, it is a side

discharge mower. If the opening is at the

back of the mower housing, it is a rear dis-

charge mower. Only rear discharge lawn

mowers have a grass catcher included

with the mower. Approved grass catch-

ers for side discharge mowers may be

purchased from your nearest authorized

dealer.

Do I have a mulching lawn mower?

Look for the grass discharge opening on

your mower. Raise the discharge guard

(rear door on rear discharge mowers). If

the opening is closed off by a plate, then

your tawn mower is mulcher ready. To

convert to a discharging mower, see the

Operation section of this manual

What is the right and left side of the

lawn mower?

When right hand (RH) or left hand (LH) is

mentioned in this manual, it means when

you are in the operating position (standing

behind the handle).

FRONT

//

LEFT ii RIGHT

HAND HAND

SIDE SIDE

BACK or REAR

(Operating Position)

What kind of engine is on my lawn

mower?

When learning how to operate your new

tawn mower, you will need to know what

kind of engine powers the mower. A decal

on the engine will indicate the manu-

facturer and type or brand name of the

engine.

BRIGGS & STRA_ON ENGINES

[,BRIGGS & STRATTON)

QUAnTUm,

OTHER ENGINES

RitTO

4

_I,CAUTION: Do not operate this lawn

mower without the discharge guard or an

entire approved grass catcher in place.

These guards are for your protection and

are required by the American National

Standards Institute and Consumer Prod-

ucts Safety Commission.

,Ii_CAUTION: Disconnect spark plug wire

from spark plug and place wire where it

cannot come in contact with plug,

HOW TO SET UP YOUR MOWER

UNFOLD HANDLE

IMPORTANT: Unfold handle carefully so

as not to pinch or damage control cables.

2 POSITION / "ADJUSTABLE" HANDLES

• Raise handles until lower handle section

locks into place in operating position.

"QUICK RELEASE" HANDLES

• Move height adjustment lever forward to

raise mower to highest position.

• Tighten handle bolts (on both sides).

Operator MOWING

presence

LIFT

UP

Upper

handle

Handle

lever

handle

Handle

bolt

Height

adjuster

lever

LEVER

FORWARD

TO RAISE

MOWER

3 POSITION "EZ" HANDLES

• Raise lower handle section to operating

position and align hole in handle with

one of three height positioning holes.

• Insert handle bolt through handle and

bracket and secure with knob.

° Repeat for opposite side of handle.

Handle

bracket

Knob

Belt

3 POSITION "QUICK" HANDLES

• Raise lower handle section to operating

position and squeeze the bottom ends

of lower handle towards each other

until the pin in handle can be inserted

into one of the three height adjustment

holes,

Handle pin

SQUEEZE

J

Handle

adj

bracket

ALL HANDLES

° Raise upper handle section into place on

lower handle, remove protective padding

and tighten both handle knobs.

° Remove handle padding holding opera-

tor presence control bar to upper handle.

° Your lawn mower handle can be ad-

justed for your mowing comforL Refer to

"ADJUST HANDLE" in the Service and

Adjustments section of this manual.

NOTE: For shipping purposes, the rear

wheels on your tawn mower may not be

adjusted to the same position as the front

wheels. Before operating mower adjust all

5 wheels to the same cutting height.

INSTALL REAR WHEELS

("HIGH WHEEL" MOWERS ONLY)

Some high wheel models require washers

which will be provided in a parts bag. tf

provided, instali washers on the axle first

as shown.

* Install one (1) rear wheel on the axle of

rear wheel adjuster.

, Install 3/8-16 locknut and tighten se-

curely.

, Repeat procedure for other rear wheel.

Axle

O-Ring

Flanged

Iocknut assembly

ASSEMBLE GRASS CATCHER

(REAR DISCHARGE MOWERS ONLY)

IMPORTANT: If your model lawn mower

is mulcher ready, the mu]cher plate or plug

must be removed before using mower as

a bagger. To convert mower to bagging or

discharging, see the Operation section in

this manual.

Look at the different grass catcher illustra-

tions that follow. Determine which type

of grass catcher you have and folIow the

appropriate instructions.

"FABRIC TOP" GRASS CATCHERS

TO ASSEMBLE AND ATTACH GRASS

CATCHER

• Put grass catcher frame into grass bag

with rigid part of bag on the bottom.

• Slip vinyl bindings over frame.

NOTE: if vinyl bindings are too stiff, hold

them in warm water for a few minutes. If

bag gets wet, let it dry before using.

• Lift the rear door on the mower housing.

• For HINGE BRACKET mounted catcher,

place the grass catcher frame onto the

formed tabs on the rear door hinge

bracket.

"_--" Rear door

bracket

Grass

catcher

frame

---_..

Formed tabs

• For HANDLE BRACKET mounted

catcher, place frame side hooks into

slots in handle brackets.

Handle bracket hooks Rear

Grass

catcher

handle

Catcher frame side hook

ForDOORPIVOTPINmounteclcatcher,

placethegrasscatcherframehooks

ontothedoorpivotpins.

Pivotpins Rear Grass

catcher

handle

Catcher frame hook

• For DOOR SLOT mounted catcher,

place the grass catcher frame hooks into

the slots of the rear door,

NOTE: The grass catcher is secured to the

lawn mower housing when the rear door is

lowered onto the grass catcher frame.

Rear door slots

Grass

catcher

handle

SPARK PLUG BOOT

On some models a spark plug boot is

)acked loose in the parts bag. If your

model has the boot, install on spark plug

wire and reconnect spark plug wire to

spark plug.

i Spark plug ........ j

Catcher frame hook

ALL GRASS CATCHERS

_CAUTION: Under normal usage, the

catcher material is subject to deterioration

and wear and should, therefore, be

checked frequently for replacement. Any

replacement catcher should be checked to

ensure compliance with original manufac-

turer's specifications,

_CAUTION: Do not run lawn mower

without the discharge guard (rear door),

approved grass catcher, clipping deflector

or mulcher plate in place. Never attempt

to operate mower with the discharge guard

(rear door) removed or propped open.

TO PREPARE BATTERY

(ELECTRIC START MODELS ONLY)

NOTE: Your battery must be charged

before you can start your lawn mower,

• Open battery box (if equipped).

• Disconnect engine connector (male)

(if equipped) from battery connector

(female).

• Connect battery charger connector

(male) to harness connector (female).

• Plug battery charger into 1t0 volt A,C.

outlet.

• Leave battery charger connected for 24

hours before starting your engine for the

first time.

• Reconnect engine connector (male) (if

equipped) to batten/connector (female).

• Aftercharging, connect engine connector

(mate) (if equipped) to battery connector

(female).

Connect your battery charger to charge

battery after each use.

IMPORTANT: The engine will not recharge

your battery.

At the end of the mowing season the

battery should be charged for 48 hours to

protect the battery during winter storage,

&CAUTION: Always disconnect the

engine connector from the battery con-

nector to prevent accidental starting when

transporting or storing your lawn mower

after the season.

\

HANDLE-MOUNTED KEY SWITCH

Engine Harness

connector connector

Charger _

connector (male)

22PLUS FRONT WHEEL DRIVE

Engine battery Battery

connector (male) er

Charger

connector

(male)

Battery connector (female)

DECK-MOUNTED BATTERY

Battery

Harness

connector

(female)

Charger

connector

(male)

Battery

box

Engine connector (male)

22PLUS REAR WHEEL DRIVE

Batter

Harness

connector

(female)

Battery

box

The operation of any lawn mower can result in foreign objects thrown into

the eyes, which can result in severe eye damage. Always wear safety

glasses or eye shields while operating your tawn mower or performing any

adjustments or repairs. We recommend standard safety glasses or a wide

vision safety mask worn over spectacles,

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED CONTROL

MODELS WITH REMOTE THROTTLE

Engine speed is controlled by the throttle

control located on the upper handle.

• Move lever forward to FAST engine

speed for starting and better bagging.

• Move Sever backward for SLOW engine

speed.

• Some models have engines equipped

with a choke feature. Move the lever all

the way forward to the CHOKE position

when starting a cold engine.

NOTE: Be sure engine START!STOP

switch (if equipped) is in the ON position.

SLOW

FAST .- ..

"_ slJ _J I,, tl

//"-_ I I i -

,.//I ,'Ji

_,, _v _

,,___/" r / -""- Remote

throttle

_z control

MODELS WITH FIXED SPEED ENGINES

Engine speed was set at the factory for

optimum performance. Engine speed is

not adjustable.

TO ADJUST CUTTING HEIGHT

ALL MODELS:

Adjust cutting height to suit your require-

ments. Medium position is best for most

lawns. Raise wheels for low cut and lower

wheels for high cut.

NOTE: For shipping purposes, the rear

wheels on your lawn mower may not be

adjusted to the same position as the front

wheels. Before operating mower adjust all

wheels to the same cutting height.

"MAN UAL" ADJUSTMENT

• Remove wheel, bolt, and hardware and

reassemble in desired adjustment hob.

• Reinstall wheel components in the same

order as they were before removai.

Tighten securely,

• Make sure all wheels are at same height.

Rat washer

Bolt

3/8-16

Spacer Locknut

"QUICK" ADJUSTMENT

• To change cutting height, squeeze adjuster

lever toward wheel. Move wheel up or

down to suit your requirements. Be sure

all wheels are in the same setting,

NOTE: Adjuster is properly positioned when

plate tab inserts into hole in lever. Also, 9-

position adjusters (if so equipped) allow lever

to be positioned between the plate tabs.

LEVER BACKWARD Plate tab

TO LOWER MOWER

LEVERFORWARDTO RAISEMOWER Lever

9

"QUICK-PIN" ADJUSTMENT

• To change cutting height, pull up on

adjuster lever, move wheel up or down

to suit your requirements and release

adjuster lever. Be sure all wheels are in

the same setting.

NOTE: Adjuster is properly positioned

when lever inserts into hole in plate.

LEVER BACKWARD _

TO LOWER MOWER

"DUAL POINT" ADJUSTMENT

Both front wheels are adjusted by a single

lever on the left front wheel. Likewise,

both rear wheels are adjusted by a single

lever on the left rear wheel.

• Putt adiuster lever toward wheel. To

raise mower, move Iever forward to

desired position. To lower mower, move

the lever toward the rear.

Be sure to adjust both front and rear

wheels to the same height.

Height uster lever

LEVER BACKWARD

TO LOWER MOWER

LEVER FORWARD

TO RAISE MOWER

LEVER

FORWARD

TO RAISE MOWER

"SINGLE POINT" ADJUSTMENT

• Pult adiuster lever toward wheel. To

raise mower, move lever forward to

desired position. To lower mower, move

the lever toward the rear.

Height

adj

LEVER

BACKWARD

TO LOWER

MOWER

LEVER

FORWARD

TO RAISE

MOWER

"THREE POINT" ADJUSTMENT

(18" (45cm) Ht-VAC MODELS ONLY)

Both rear wheels are adjusted by a single

lever on the left rear wheel.

• Pull adjuster lever toward wheel. To

raise mower, move lever forward to

desired position. TO lower mower, move

the ]ever toward the rear.

NOTE: There are seven (7) height adjust-

ment positions for the rear wheels.

Both front wheels are adjusted as follows:

t. Remove wheel, bolt, and hardware and

reassemble in desired adjustment hole.

2. Reinstall wheel components in the

same order as they were before re-

moval. Tighten securely.

NOTE: There are seven (7) height adjust-

ment holes for the front wheels. Be sure

both front wheels are in the same hole.

IMPORTANT: Be sure to adjust both front

and rear wheels to the same height.

LEVER BACKWARD

TO LOWER REAR

OF MOWER

usterlever

LEVER FORWARD

TO RAISE REAR

OF MOWER

Bolt

Lockbar

position)

Wing

Washel

Lockbar

("freewheel"

position)

CASTER WHEEL OPERATION '

('q'HREE POINT" ADJUSTMENT ONLY)

The front wheels can be "locked" into

position or set to "freewheel" for better

maneuverability. Placing the lockbars in

the outer holes of the adjustment brackets

"locks" the front wheels. Likewise, placing

the tockbars in the inner holes of the ad-

justment brackets allows the front wheels

to spin freely ('_freewheel").

- Lift tockbar until the frontmost end clears

the adjustment bracket, then pivot lock-

bar to desired position.

IMPORTANT: Front wheels must be

"looked" into position when operating on

a slope. Mow across the face of slopes:

never up and down.

TO CONVERT MOWER:

Most mowers are shipped ready to be

used as a mutcher,

"REAR DISCHARGE ONLY" MOWERS

Some models have a seperate mulcher

plug, other models have the muicher plug

built into the rear door. To convert to bag-

ging or discharging, the plate or plug (if

so equipped) must be removed from the

discharge opening of the lawn mower,

• Open rear door and remove muicher

plate or plug (if so equipped). Store

mutcher plate or plug in a safe place.

• You can now install grass catcher or

optional clipping deflector accessory.

• To return to mulching operation, install

mutcher plate or plug into discharge

opening of mower.

• I,CAUTION: Do not run your fawn mower

without mulcher plate/plug in place or ap-

proved clipping deflector or grass catcher

in place. Never attempt to operate the

lawn mower with the rear door removed or

propped open.

MULCHER

"PLATE"

Mulcher

plate tabs

MULCHER

"PLUG"

Mufcher

plug

MULCHER PLUG BUILT INTO REAR DOOR

11

"SIDE DISCHARGE ONLY" MOWERS

MULCHER PLATE

To convert to bagging or discharging,

mulcher plate must be removed from un-

derside of lawn mower.

• Remove the four (4) screws and lock nuts

securing the mulcher prate to the mower.

• Store mutcher plate and hardware in a

safe place.

° Mower can now be used for side

discharging or optional grass catcher

accessory can be attached,

• To return to mulching operation, simply

reinstall mulcher plate and tighten hard-

ware securely.

Screw and _ k._---.

lock nut _ x,.__

" _ 0 ML_cher

MULCHER PLUG TYPE "A"

To convert to mulching operation, mulcher

plug must be installed into discharge open-

ing of mower.

• Open discharge guard.

• Insert tab of mulch plug into housing

opening.

° Align hooks of mulch plug over hinge

rod of discharge guard, Push mulch plug

down unt;_ mulch plug is seated in hous-

ing opening.

_&CAUTION: Do not run your lawn mower

without discharge guard, approved grass

catcher or mutcher plug in place.

MULCHER PLUG TYPE "B"

To convert to bagging or discharging:

° Lift discharge guard and remove

mutcher plug.

• Mower can now be used for side dis-

charging or optional grass catcher can

be attached.

• To return to mulching operation, simply

reinstall mulcher plug as shown, making

sure tab is seated properly.

&CAUTION: Do not run your lawn mower

without discharge guard, approved grass

catcher or mulcher plug in place.

Lift

dischar(

guard

Install Tab

MOWER iS

NOW READY

FOR MULCH1NG

OPERATION

Discharge

Housing

ol

Mutcher plug 12

"MULTI-CUT"MOWERS

"Your lawn mower was shipped ready to be

used as a mulcher, To convert to bagging

or discharging:

REAR BAGGING

• Open rear door and remove mulcher

plate or plug (if equipped). Store

mulcher plate or plug in a safe place,

o You can now install grass catcher,

• To convert to mulching or discharging

operation, instaU mu]cher plate or plug (if

equipped) into rear discharge opening of

mower, making sure all tabs are seated

properly. Close rear door,

bracket Grass

catcher

handle

Fu{l bag -

catcher indicator

frame window (if

hook equipped)

"REAR DOOR PROP" (lF EQUIPPED)

(22PLUS MODELS ONLY)

NOTE: Rear door will remain open until

operator presence control bar is held down

to the handte.

,_,CAUTION: Do NOT force rear door to

close, Serious damage to your mower

could result.

....._:_i!;,:,_:_':.........................:,:,:_i!i_?,_......

SIDE DISCHARGING

• Mulcher plate or plug (if equipped) must

be installed into rear discharge opening

of mower. Rear door must be closed.

• Open mulcher door and installdischarge

deflector under door as shown.

• Mower is now ready for discharging

operation.

° To convert to mulching or bagging

operation, discharge deflector must be

removed and mulcher door must be

closed and locked.

f

Unloc£

latch (if -_-'_

equipped)

J

Open mulcher door I

Discharge

deflector

/

13

SIMPLE STEPS TO REMEMBER

WHEN CONVERTING YOUR

"MULTI-CUT" LAWN MOWER:

FOR MULCHING -

• Rear mutcher plate or plug (if equipped)

installed and rear door closed.

• Mulcher door closed.

FOR REAR BAGGING -

• Rear mulcher plate or plug (if equipped)

removed.

• Grass catcher installed.

• Mutcl_er door closed.

FOR SIDE DISCHARGING -

• Rear mulcher plate or plug (if equipped)

installed and rear door closed.

• Discharge deflector installed•

,_CAUTION: Do not run your lawn mower

without rear mulcher plate or plug in place

or approved grass catcher in place. Never

attempt to operate the lawn mower with

the rear door removed or propped open.

TO EMPTY GRASS CATCHER (REAR

DISCHARGE AND MULTI-CUT MODELS)

- Simp{y open rear door and lift grass

catcher up and away from mower.

NOTE: Do not drag the bag when

emptying. It will cause unnecessary wear, Dis-

,_CAUTION: Under normal usage, the charge

catcher material is subject to deterioration

and wear and should, therefore, be

checked frequently for replacement. Any

replacement catcher should be checked

to ensure compliance with original

manufacturer's specifications.

_,CAUTION: Do not run lawn mower

without the rear door, approved grass

catcher or clipping deflector in place.

Never attempt to operate mower with the

rear door removed or propped open.

if / Grass

catcher

frame

18" (45cm) HI-VAC MODELS:

Your lawn mower was shipped ready to

be used as a mulcher. To convert to rear

bagging or side discharging:

REAR BAGGING

!. Remove knob securing mutcher door

to lawn mower housing.

2, Open mufcher door and position dis-

charge chute over both threaded studs.

3, Secure discharge chute to lawn mower

housing with both knobs.

4, Place the grass catcher on the rear

door as shown.

NOTE: Be sure the grass catcher is se-

curely locked in place,

° Mower is now ready for rear bagging

operation.

door

Knobs

Mulcher

door

SIDE DISCHARGING

1. Discharge chute must be removed,

2. Open mulcher door and install side dis-

charge deflector beneath it as shown.

(if equipped)

14 Side discharge deflector

Knob _ Threaded stud

L,,,J

_ ' Mutcher

door

3. Secure rear of side discharge deflector

to lawn mower housing with knob.

° Mower is now ready for side discharging

operation.

SIMPLE STEPS TO REMEMBER WHEN

CONVERTING YOUR 18" HI-VAC:

FOR MULCHING -

1. Grass catcher, discharge chute and

side discharge deflector removed.

2. Mulcher door secured to mower hous-

ing with knob.

FOR REAR BAGGING -

1. Side discharge deflector removed.

2. Grass catcher and discharge chute

installed with discharge chute secured

to lawn mower housing with knob.

FOR SIDE DISCHARGING -

1. Grass catcher and discharge chute

removed.

2. Side discharge deflector installed and

secured to mower housing with knob.

_,CAUTION: Do not run your lawn mower

without mulcher door closed; side dis-

charge deflector installed, or discharge

chute and approved grass catcher in

place. Never attempt to operate the lawn

mower with mulcher door removed or

propped open.

TO EMPTY GRASS CATCHER

t. Remove grass catcher with clippings

from lawn mower using both front and

center of handle as shown.

2. Empty clippings from grass catcher.

3. Reinstall grass catcher on rear door.

NOTE: Do not drag the bag when empty-

ing; it will cause unnecessary wear.

Handle

21" (53cm) HI-VAC MODELS:

Your lawn mower was shipped ready to

be used as a mulcher. To convert to rear

bagging or side discharging:

REAR BAGGING

1. Remove knob securing mulcher door to

fawn mower housing.

_rhandle

Crossbar

Grass

Round

door

chute

Threaded

stud

Muicher door

2,

Open mulcher door and insert tabs

of discharge chute into hinge bracket

opening and position rear of chute over

threaded stud.

Hinge bracket Mulcher door

t5

3, Secure rear of discharge chute to lawn

mower housing with knob,

4, Place rear handle of grass catcher on

the crossbar of the lawn mower's lower

handle as shown.

5, Lift the round door of the discharge

chute and place the grass catcher into

place on the discharge chute.

NOTE: Be sure the grass catcher is se-

curely locked in place and the round door

of the discharge chute rests on the grass

catcher as shown,

• Mower is now ready for rear bagging

operation.

° To convert to mulching operation,

remove grass catcher and discharge

chute. Secure mulcher door to mower

housing with knob.

° To convert to side discharging operation,

remove grass catcher and discharge

chute. Install side discharge deflector

and secure it to lawn mower housing

with knob.

SIDE DISCHARGING

1, Grass catcher and discharge chute

must be removed.

2. Open mufcher door and install front of

side discharge deflector beneath it as

shown.

3. Secure rear of side discharge deflector

to lawn mower housing with knob.

° Mower is now ready for side discharging

operation.

° To convert to mulching operation, side

discharge deflector must be removed

and mulcher door secured to mower

housing with knob.

• To convert to rear bagging opera-

tion, side discharge deflector must be

removed; discharge chute and grass

catcher installed and discharge chute

secured to mower housing with knob.

Mulcher door _ Knob

Y

stud

Side

discharge

deflector

SIMPLE STEPS TO REMEMBER

WHEN CONVERTING YOUR 21" HI-VAC:

FOR MULCHING -

1. Grass catcher, discharge chute and

side discharge deflector removed.

2. Mutcher door secured to mower hous-

ing with knob,

FOR REAR BAGGING -

1, Side discharge deflector removed,

2. Grass catcher and discharge chute

installed with discharge chute secured

to lawn mower housing with knob.

3, Round door of discharge chute resting

on top of grass catcher.

FOR SIDE DISCHARGING -

1. Grass catcher and discharge chute

removed,

2. Side discharge deflector installed and

secured to mower housing with knob,

_CAUTtON: Do not run your lawn mower

without mulcher door dosed; side dis-

charge deflector installed, or discharge

chute and approved grass catcher in

place. Never attempt to operate the lawn

mower with mulcher door or round door

removed or propped open.

TO EMPTY GRASS CATCHER

1. Open round door of discharge chute to

move starter rope out and away from

grass catcher.

',\'_ Front

OPEN

Round Starter

door rope

2. Remove grass catcher with clippings

from lawn mower using both front and

rear handles,

3. Empty clippings from grass catcher

using rear handle. The weight of the

grass will open the door.

4, Snap door shut over frame before

installing grass catcher on mower.

NOTE: Do not drag the bag when empty-

!6 ing; it will cause unnecessary wear.

OPERATOR PRESENCE CONTROL

BAR (ALL MODELS)

Your lawn mower is equipped with an op-

erator presence control bar which requires

the operator to be positioned behind the

lawn mower handle in order to start and

,_cerate the lawn mower.

AUTION: Federal regulations require

an engine control to be installed on this

lawn mower in order to minimize the risk

of blade contact injury. Do not under

any circumstances attempt todefeat the

function of the operator control. The blade

turns when the engine is running.

DRIVE CONTROL

"STANDARD" DRIVE CONTROL

• Self-propelling is controlled by holding

the operator presence control bar down

to the handle and pushing the drive

control lever forward until it clicks; then

releasing the lever,

• Forward motion will stop when the op-

erator presence control bar is released.

To stop forward motion without stopping

engine, release the operator presence

control bar slightly until the drive control

disengages, Hold operator presence

control bar down against handle to con-

tinue mowing without self-propelling.

• To keep drive control engaged when

turning corners, push down on handle

and lift front wheels off ground while

turning lawn mower.

Drive

control

TO ENGAGEDRIVECONTROL

\

Operator

presence

control bar

DRIVE CONTROL DISENGAGED

17

"DUAL BAIL" DRIVE CONTROL

• To start forward motion, lift drive control

bar up to handle.

• To stop forward motion, release drive

control bar.

DRIVE CONTROL ENGAGED

DRfVE CONTROL DISENGAGED

"AUTOWALK" DRIVE CONTROL

• Self-propelling is controlIed by holding

the operator presence control bar down

to the handle and pulling the drive con-

trol lever(s) rearward to the handle, The

farther toward the handle the lever(s)

are pulled, the faster the unit will travel,

• Forward motion will stop when either

the operator presence control bar or a

drive control lever are released. To stop

forward motion without stopping engine,

release the drive control lever(s) only.

Hold operator presence control bar

down against handle to continue mowing

without self-propelling.

NOTE: If after releasing the drive control the

mower wilI not roll backwards, push the mower

forward slightly to disengage drive wheels.

TO ENGAGE DRIVE CONTROL

lurnbuckle

DRIVE CONTROL DISENGAGED

FRONT WHEEL DRIVE MODELS ONLY:

° To keep drive control engaged when

turning corners, push down on the

handle to lift the front wheels off the

ground while turning lawn mower.

18

Over time, the drive control system may

become "loose", resulting in decreased

speed. There is a turnbuckle on the

underside of the drive control housing to

increase tension on the drive cable. Pro-

ceed as follows:

• Turn unit off and disconnect spark plug

wire from spark plug.

° Turn nut on underside of drive control to

increase drive speed.

• Operate mower to test drive speed.

Readjust as required.

• If condition fails to improve after the

above steps (forward speed remains

the same), your drive belt is worn and

should be replaced.

turnbuckle

"VARI-SPEED" DRIVE CONTROL

• Self-propelling is controlled by hold-

ing the operator presence control bar

down to the handle and pulling the drive

control bar up to the handle, The closer

to the handle the bar is pulled, the faster

the unit will travel.

• Forward motion will stop when either the

operator presence control bar or drive

control bar are released. To stop forward

motion without stopping engine, release

the drive control bar only, Hold operator

presence control bar down against

handle to continue mowing without self-

propelling.

NOTE: Ifafter releasing the drive control the

mower will not rollbackwards, push the mower

forward slightly to disengage drive wheels.

FRONT WHEEL DRIVE MODELS ONLY:

• To keep drive control engaged when

turning corners, push down on the

handle to lift the front wheels off the

ground while turning lawn mower.

presence control bar

control bar

DRIVE

CONTROL

DISENGAGED

TO ADJUST,

MOVE DOWN

TO NEXT HOLE

Over time, the drive control system may

become "loose", resulting in decreased

speed. There are holes in the drive control

housing to increase tension on the drive

cable. Proceed as follows:

° Turn unit off and disconnect spark plug

wire from spark plug.

• Loosen nut, move drive control hous-

ing down handle to the next hole and

retighten nut.

• Operate mower to test drive speed.

• If condition fails to improve after the

above steps (forward speed remains

the same), your drive belt is worn and

should be replaced.

19

BEFORE STARTING ENGINE

Read the engine manual packed with your

mower.

FILL ENGINE WITH OIL

Your lawn mower is shipped without oil in

the engine.

- Be sure mower is level and area around

oi! fill is clean.

• Remove engine oil filler plug (oil fill cap/

dipstick on models so equipped).

• Slowly add oil. For type and grade of

oil to use, see "ENGINE" in the Mainte-

nance section of this manual.

• Fill to the top of slot in filler hole (to

"FULL" line on dipstick on models so

equipped). Do not overfill.

• Replace plug (oil fill cap/dipstick on

models so equipped) and tighten.

• Check oil level before each use. Add oil

as needed.

• To change oil, see Maintenance section

of this manual.

FILL GASOLINE TANK

• Fill gasoline tank with fresh, clean,

unleaded gasoline. DO NOT USE PRE-

MIUM GASOLINE. BE CAREFUL NOT

TO OVERFILL TANK.

WARNING: Alcohol blended fuels (called

gasohol or using ethanol or methanol) can

attract moisture which leads to separation

and formation of acids during storage. Acidic

gas can damage the fuel system of an engine

while in storage. To avoid engine problems,

the fuel system should be emptied before

storage of 30 days or longer. Drain the fuel

tank, start the engine and let it run until fuel

lines and carburetor are empty. Use fresh

fuel next season. See Storage Instructions

for additional information. Never use engine

or carburetor cleaner products in fuel tank or

permanent damage may occur.

TO START ENGINE

_CAUTION: The mower blade rotates

whenever the engine is running.

NOTE: Due to protective coatings on the

engine, a small amount of smoke may be

present during the initial use of the product

and should be considered normal.

• Place engine START/STOP switch (if

equipped) in the ON position.

° Move engine speed control to FAST

position (or to CHOKE/START position

on models equipped with choke feature).

• If your mower has a primer, to start a

cold engine, push primer as many times

as instructed in the engine manual

packed with your mower. Use a firm

push. This step is not usually necessary

when starting an engine which has

already run for a few minutes.

• Hold operator presence control bar

down against handle.

MODELS WITH RECOIL STARTER

• Pull starter handle quickly. Do not allow

starter rope to snap back.

Recoil

starter

handle

MODELS WITH ELECTRIC STARTER

• Push the engine start button (or turn the

key on models so equipped).

IMPORTANT: Do not crank engine more

than five continous seconds each time you

try to start. Wait 5 to 10 seconds between

each attempt.

ALL MODELS

° For engines equipped with choke, slowly

move engine speed control lever to

FAST after engine starts.

TO STOP ENGINE

° To stop engine, release operator pres-

ence control bar and/or place engine

START/STOP switch (if equipped) in the

OFF position.

NOTE: For engines with a primer, it may

be necessary to repeat priming steps

in cooler weather. In warmer weather,

overpdming may cause flooding and

engine wilt not start. If you do flood

engine, wait a few minules before

attempting to start and DO NOT repeat

priming steps,

2O

La page charge ...

Yard Pro Y160Y21R Le manuel du propriétaire

Ce manuel convient également à

Yard Pro Y160Y21R Le manuel du propriétaire

dans d''autres langues

Autres documents