Husqvarna 961450011 Manuel utilisateur

Marque: Husqvarna

Modèle: 961450011

Catégorie: Outils de jardin

Taper: Manuel utilisateur

English/French

115 53 97-31 Rev. 1

Operator’s Manual

Manuel de L’Opérateur

HU800AWD / 961450011

Gasoline containing up to 10% ethanol (E10) is accept-

able for use in this machine. The use of any gasoline ex-

ceeding 10% ethanol (E10) will void the product warranty.

Vous pouvez utiliser de l’essence contenant jusqu’à

10 % d’éthanol (E10) avec cet appareil. L’utilisation

d’essence contenant plus de 10 % d’éthanol annulera

la garantie du produit.

Please read the operator's manual carefully and make sure

you understand the instructions before using the machine.

Lisez très attentivement et soyez certain de comprende

ces instructions avant d’utiliser cette machine.

CAUTION: Always disconnect spark plug

wire and place wire where it cannot contact

spark plug in order to prevent ac ci den tal

starting when setting up, trans port ing,

adjusting or making re pairs.

Look for this symbol to point out im-

por tant safety precautions. It means

CAUTION!!! BE COME ALERT!!! YOUR

SAFE TY IS IN VOLVED.

CAUTION: Mufﬂ er and other engine parts

become extremely hot during operation and

remain hot after engine has stopped. To

avoid severe burns on contact, stay away

from these areas.

Safe Operation Practices for Walk-Behind Mowers

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE

TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

SAFETY RULES

WARNING: This lawn mower is equipped with an in-

ternal com bus tion engine and should not be used on or

near any un im proved forest-covered, brush-covered or

grass-cov ered land unless the engine’s exhaust system

is equipped with a spark arrester meeting applicable local

or state laws (if any). If a spark arrester is used, it should

be maintained in effective working order by the operator.

A spark arrester for the mufﬂ er is available through your

nearest authorized service center.

WARNING: Engine exhaust, some of its con stit u ents,

and certain vehicle com po nents contain or emit chem i cals

known to the State of Cal i for nia to cause can cer and birth

defects or oth er re pro duc tive harm.

WARNING: Battery posts, terminals and related ac ces-

so ries contain lead and lead compounds, chemicals known

to the State of Cal i for nia to cause can cer and birth defects

or oth er re pro duc tive harm. Wash hands after handling.

I. GENERAL OPERATION

• Read, understand, and follow all instructions on the

machine and in the manual(s) before starting. Be

thor ough ly familiar with the controls and the proper

use of the machine before starting.

• Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

• Only allow responsible individuals, who are familiar

with the instructions, to operate the machine.

• Clear the area of objects such as rocks, toys, wire,

bones, sticks, etc., which could be picked up and

thrown by the blade.

• Be sure the area is clear of other people before mow-

ing. Stop machine if anyone enters the area.

• Do not operate the mower when barefoot or wearing

open sandals. Always wear substantial foot wear.

• Do not pull mower backwards unless absolutely nec es-

sary. Always look down and behind before and while

moving backwards.

• Never direct discharged material toward anyone.

Avoid discharging material against a wall or obstruc-

tion. Material may richochet back toward the operator.

Stop the blade when crossing gravel surfaces.

• Do not operate the mower without proper guards,

plates, grass catcher or other safety protective devices

in place.

• See manufacturer’s instructions for proper operation

and installation of accessories. Only use accessories

approved by the manufacturer.

• Stop the blade(s) when crossing gravel drives, walks,

or roads.

• Stop the engine (motor) whenever you leave the equip-

ment, before cleaning the mower or unclogging the

chute.

• Shut the engine (motor) off and wait until the blade

comes to complete stop before removing grass catch er.

• Mow only in daylight or good artiﬁ cial light.

• Do not operate the machine while under the inﬂ uence

of alcohol or drugs.

• Never operate machine in wet grass. Always be sure

of your footing: keep a ﬁ rm hold on the handle and

walk; never run.

• Disengage the self-propelled mechanism or drive clutch

on mowers so equipped before starting the engine (motor).

• If the equipment should start to vibrate abnormally,

stop the engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

• Always wear safety goggles or safety glasses with side

shields when operating mower.

II. SLOPE OPERATION

Slopes are a major factor related to slip and fall accidents

which can result in severe injury. All slopes require extra

caution. If you feel uneasy on a slope, do not mow it.

DO:

• Mow across the face of slopes: never up and down. Exer-

cise extreme caution when changing direction on slopes.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Tall grass can hide

obstacles.

DO NOT:

• Do not trim near drop-offs, ditches or embankments.

The operator could lose footing or balance.

• Do not trim excessively steep slopes.

• Do not mow on wet grass. Reduced footing could cause

slipping.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last saw them.

• Keep children out of the trimming area and under the

watchful care of another re spon si ble adult.

• Be alert and turn machine off if children enter the area.

• Before and while walking backwards, look behind and

down for small children.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

WARNING: CHILDREN CAN BE INJURED BY THIS

EQUIPMENT. The American Academy of Pediatrics rec-

ommends that children be a minimum of 12 year of age

before operating a pedestrian controlled lawn mower and

a minimum of 16 years of age before operating a riding

lawn mower.

SAFETY RULES .........................................................2-3

PRODUCT SPECIFICATIONS ....................................... 3

CUSTOMER RESPONSIBILITIES ................................. 3

ASSEMBLY .................................................................... 4

OPERATION ............................................................... 5-9

MAINTENANCE SCHEDULE ...................................... 10

MAINTENANCE ...................................................... 10-13

SERVICE AND AD JUST MENTS ............................14-16

STORAGE ...............................................................16-17

TROU BLE SHOOT ING ................................................. 18

WARRANTY ............................................................19-22

CONGRATULATIONS on your purchase of a new lawn

mower. It has been designed, engineered and man u fac tured

to give you the best possible dependability and performance.

Should you experience any problem you cannot easily

remedy, please contact your nearest authorized service

center/department. We have competent, well-trained

tech ni cians and the proper tools to service or repair this

lawn mower.

Please read and retain this manual. The instructions will

enable you to assemble and maintain your lawn mower

properly. Always observe the “SAFETY RULES”.

SERIAL

NUMBER: _________________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND

ON A DECAL ATTACHED TO THE REAR OF THE LAWN

MOWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND

DATE OF PURCHASE AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for

and using your lawn mower.

• Follow the instructions under “Maintenance” and “Stor-

age” sec tions of this own er’s manual.

TABLE OF CONTENTS

PRODUCT SPECIFICATIONS

Gasoline Capacity 1 Quart

and Type: (Unleaded Regular Only)

Oil Type (API SG–SL): SAE 30 (above 0°C / 32°F)

SAE 10W-30 (below 0°C / 32°F)

Oil Capacity: 0.58 Quarts

Spark Plug: NGK BPR6ES (Gap: .030")

Valve Clearance: Intake: 0.015 mm

(± 0.04 mm) Exhaust: 0.020 mm

Blade Bolt Torque: 35–40 ft. lbs.

• When loading or unloading this machine, do not exceed

the maximum recommended operation angle of 15°.

• Wear proper Personal Protective Equipment (PPE)

while operating this machine, including (at a minimum)

sturdy footwear, eye protection, and hearing protection.

Do not mow in short and/or, open toed footwear.

Always let someone know you are outside mowing.

IV. SAFE HANDLING OF GASOLINE

Use extreme care in handling gasoline. Gasoline is ex-

tremely ﬂ ammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

• Use only an approved container.

• Never remove gas cap or add fuel with the engine

running. Allow engine to cool before refueling.

• Never refuel the machine indoors.

• Never store the machine or fuel container where there

is an open ﬂ ame, spark or pilot light such as a water

heater or on other appliances.

• Never ﬁ ll containers inside a vehicle, on a truck or trailer

bed with a plastic liner. Always place containers on

the ground away from your vehicle before ﬁ lling.

• Remove gas-powered equipment from the truck or

trailer and refuel it on the ground. If this is not possible,

then refuel such equipment with a portable container,

rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank

or container opening at all times until fueling is complete.

Do not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immediately.

• Never overﬁ ll fuel tank. Replace gas cap; tighten securely.

V. GENERAL SERVICE

• Never run a machine inside a closed area.

• Never make adjustments or repairs with the engine

(motor) running. Disconnect spark plug wire, and keep

wire away from plug to prevent accidental starting.

• Keep nuts and bolts, especially blade attachement

bolts, tight and keep equipment in good condition.

• Never tamper with safety devices. Check their proper

operation regularly.

• Keep machine free of grass, leaves, or other debris

build-up. Clean oil or fuel spillage. Allow machine to

cool before storing.

• Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

• Never attempt to make wheel height adjustments while

the engine (motor) is running.

• Grass catcher components are subject to wear, dam-

age, and deterioration, which could expose moving

parts or allow objects to be thrown. Frequently check

com po nents and replace with manufacturer’s rec om-

mend ed parts, when necessary.

• Mower blade is sharp and can cut. Wrap the blade or

wear gloves, and use extra caution when servicing it.

• Do not change the engine governor setting or overspeed

the engine.

• Maintain or replace safety and instruction labels, as

necessary.

ASSEMBLY

Read these instructions and this man u al in its entirety before you attempt to assemble or operate your new lawn mow er.

IMPORTANT: THIS LAWN MOWER IS SHIPPED WITH OUT OIL OR GASOLINE IN THE ENGINE.

Your new lawn mower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping

purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as sem bly have been placed in the parts

bag. To ensure safe and proper operation of your lawn mow er, all parts and hard ware you assemble must be tightened

se cure ly. Use the correct tools as nec es sary to ensure proper tightness.

TO ASSEMBLE GRASS CATCHER

(See Fig. 3)

1. Put grass catcher frame into grass bag with rigid part

of bag on the bottom. Make sure the frame handle is

outside of the bag top.

2. Slip vinyl bindings over frame.

NOTE: If vinyl bindings are too stiff, hold them in warm water

for a few minutes. If bag gets wet, let it dry before using.

TO INSTALL ATTACHMENTS

Your lawn mower was shipped ready to be used as a

mulcher. To convert mower to bagging or discharging,

see “TO CON VERT MOWER” in the Operation section of

this man u al.

FIG. 1

OPERATOR

PRESENCE

CONTROL

BAR

HANDLE

KNOB

LIFT

LOWER

HANDLE

MOWING

PO SI TION

UPPER

HANDLE

FIG. 3

FRAME

HANDLE

VINYL

BINDINGS

FRAME

OPENING

TO RE MOVE LAWN MOW ER FROM CAR TON

1. Remove loose parts included with mower.

2. Cut down two end corners of car ton and lay end panel

down ﬂ at.

3. Remove all packing materials ex cept padding be tween

upper and lower handle and padding holding operator

presence control bar to up per handle.

4. Roll lawn mower out of carton and check carton thor-

ougly for ad di tion al loose parts.

HOW TO SET UP YOUR LAWN MOW ER

TO UNFOLD HANDLE (See Figs. 1 and 2)

IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS

NOT TO PINCH OR DAMAGE CON TROL CABLES.

1. Raise lower handle section to operating position and

align hole in handle with one of three height positioning

holes.

2. Insert handle bolt through handle and bracket and

secure with knob.

3. Repeat for opposite side of handle.

4. Remove protective padding, raise upper handle sec-

tion into place on lower handle and tighten both handle

knobs.

5. Remove any packing material from around control

bar.

Your handles may be adjusted for your mowing comfort.

Refer to “ADJUST HANDLE” in the Service and Ad just ments

sec tion of this man u al.

FIG. 2

HANDLE

BRACKET

BOLT

KNOB

KNOW YOUR LAWN MOWER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER.

Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments.

Save this manual for future reference.

MEETS CPSC SAFETY REQUIREMENTS

Husqvarna rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards In-

stitute and the U.S. Consumer Product Safety Commission. WARNING: The blade turns when the engine is running.

OPERATOR PRESENCE CONTROL BAR – must be held

down to the handle to start the engine. Release to stop

the engine.

STARTER HANDLE – used for starting the engine.

HOUSING

GRASS

CATCHER

DRIVE CONTROL LEVERS – used to engage power-

propelled forward motion lawn mower.

MULCHER DOOR – allows con ver sion to discharging or

bagging operation.

OPERATOR PRESENCE CON TROL BAR

STARTER

HANDLE

EN GINE OIL CAP WITH DIPSTICK

MULCHER DOOR

HANDLE KNOB

GAS O LINE FILL ER CAP

These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand

their meaning.

OPERATION

IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.

NOTE: Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline ex-

ceeding 10% ethanol (E10) will void the product warranty.

DRIVE CONTROL

LEVERS

MUFFLER

WHEEL HEIGHT ADJUSTER

(ON EACH WHEEL)

AIR FILTER

DRIVE

COVER

SPARK PLUG

FUEL SHUTOFF VALVE

TO ADJUST CUTTING HEIGHT (See Fig. 6)

Raise wheels for low cut and lower wheels for high cut,

adjust cutting height to suit your requirements. Me di um

position is best for most lawns.

• To change cutting height, pull up on adjuster lever,

move wheel up or down to suit your re quire ments and

release adjuster lever. Be sure all wheels are in the

same setting.

NOTE: Adjuster is properly positioned when lever inserts

into hole in plate.

The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in

severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or per-

forming any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask

over spectacles.

OPERATION

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

The engine speed was set at the factory for optimum per-

formance. Speed is not adjustable.

ENGINE ZONE CONTROL

CAUTION: Federal regulations require

an engine control to be installed on this

lawn mower in order to minimize the risk

of blade contact injury. Do not un der

any cir cum stanc es attempt to defeat

the function of the operator control. The

blade turns when the engine is running.

• Your lawn mower is equipped with an operator presence

control bar which requires the operator to be positioned

behind the mower handle to start and operate the mower.

DRIVE CONTROL (See Fig. 4)

• Self-propelling is controlled by hold ing the operator

presence control bar down to the handle and pulling

either drive control lever rearward to the handle. The

further toward the handle a lever is pulled, the faster

the unit will travel.

• Forward motion will stop when either the operator pres-

ence control bar or a drive control lever are released. To

stop forward motion without stop ping engine, re lease a

drive control lever only. Hold op er a tor presence control

bar down against handle to con tin ue mowing without

self-propelling.

NOTE: If after releasing the drive control the mower will

not roll backwards, push the mower forward slightly to

disengage drive wheels.

3. Operate mower to test drive speed. Readjust as re-

quired.

4. If condition fails to improve after the above steps (for-

ward speed remains the same), your drive belt is worn

and should be re placed.

TO ENGAGE

DRIVE CONTROL

DRIVE

CONTROL

LEVERS

DRIVE CONTROL

DISENGAGED

OPERATOR PRESENCE CONTROL BAR

FIG. 4

FIG. 5

ADJUSTMENT TURNBUCKLE

TO CONVERT MOWER

Your lawn mower was shipped ready to be used as a

mulcher. To convert to bagging or discharging:

REAR BAGGING (See Fig. 7)

• Lift rear door of the lawn mower and place the grass

catcher frame hooks onto the grass bag brackets.

• To convert to mulching or discharging operation, remove

grass catch er and close rear door.

DRIVE CONTROL ADJUSTMENT (See Fig. 5)

Over time, the drive control system may become “loose”,

resulting in decreased speed. There is a turnbuckle on

the drive control housing to increase tension on the drive

cable. Pro ceed as follows:

1. Turn unit off, disconnect spark plug wire from plug.

2. Rotate turnbuckle on drive control to increase drive

speed.

FIG. 6

LEVER

LEVER BACKWARD

TO LOWER MOWER

LEVER

FORWARD

TO RAISE

MOWER

PLATE

SIMPLE STEPS TO REMEMBER

WHEN CONVERTING YOUR LAWN MOWER

FOR MULCHING -

1. Rear door closed.

2. Mulcher door closed and locked.

FOR REAR BAGGING -

1. Grass catcher installed.

2. Mulcher door closed and locked.

FOR SIDE DISCHARGING -

1. Rear door closed.

2. Discharge deﬂ ector installed.

CAUTION: Do not run your lawn mower

with out rear door closed or ap proved

grass catcher in place. Never at tempt

to op er ate the lawn mow er with the rear

door re moved or propped open.

OPERATION

FIG. 7

GRASS BAG

BRACKET

REAR DOOR

GRASS

CATCHER

HANDLE

GRASS

CATCHER

FRAME HOOK

SIDE DISCHARGING (See Fig. 8)

• Rear door must be closed.

• Open mulcher door and install dis charge deﬂ ector

under door as shown.

• Mower is now ready for side discharging operation.

• To convert to mulching or bagging operation, dis charge

deﬂ ector must be removed and mulcher door must be

closed and locked.

MOWER IS NOW READY FOR

DISCHARGING OPERATION

OPEN MULCHER

DOOR

INSTALL

DISCHARGE

DEFLECTOR

FIG. 8

UNLOCK

LATCH

OPERATION

CAUTION: Alcohol blended fuels

(called gasohol or using ethanol or

methanol) can attract moisture which

leads to separation and for ma tion of

acids during storage.

Acidic gas can damage the fuel system of an

engine while in storage. To avoid engine prob-

lems, the fuel system should be emptied before

stor age of 30 days or longer. Empty the gas tank,

start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next

season. See Storage In struc tions for additional

information. Never use engine or carburetor

cleaner products in the fuel tank or permanent

damage may occur.

ADD GASOLINE (See Fig. 10)

• Fill fuel tank to bottom of tank ﬁ ller neck. Do not over-

ﬁ ll. Use fresh, clean, regular unleaded gasoline with

a minimum of 87 octane. Do not mix oil with gasoline.

Purchase fuel in quan ti ties that can be used within 30

days to assure fuel freshness.

TO STOP ENGINE (See Fig. 11)

• To stop engine, release operator presence control bar.

Wait until blade and all moving parts have stopped and

turn fuel valve to OFF position if you do not intend to

re start the engine soon.

TO START ENGINE

NOTE: Due to protective coatings on the engine, a small

amount of smoke may be present during the initial use of

the product and should be considered normal.

1. Be sure fuel valve is in the ON po si tion.

2. Move choke lever to ON ( ) position.

3. Hold operator presence control bar down to the han dle

and pull starter handle quickly. Do not allow starter rope

to snap back.

NOTE: The choke lever automatically begins moving to

the OFF position when operator presence control bar is

held down to handle.

BEFORE STARTING ENGINE

ADD OIL (See Fig. 10)

Your lawnmower is shipped without oil in the engine. For

type and grade of oil to use, see “EN GINE” in the Mainte-

nance section of this manual.

CAUTION: DO NOT overﬁ ll engine with

oil, or it will smoke heavily from the

mufﬂ er on startup.

1. Be sure lawnmower is level.

2. Remove oil ﬁ ll cap/dipstick from oil ﬁ ll spout.

3. You recieve a container of oil with the unit. Slowly

pour the entire container down the oil ﬁ ll spout into the

engine.

4. Insert and tighten oil ﬁ ll cap/dipstick.

IMPORTANT:

• Check oil level before each use. Add oil if needed. Fill

to full line on dipstick.

• Change the oil after every 25 hours of operation or each

season. You may need to change the oil more often un-

der dusty, dirty conditions. See “TO CHANGE ENGINE

OIL” in the Maintenance section of this manual.

GASOLINE

FILLER CAP

ENGINE

OIL CAP

FIG. 10

FIG. 9

GRASS

CATCHER

FRAME

HANDLE

BAG

HANDLE

TO EMPTY GRASS CATCHER (See Fig. 9)

1. Lift up on grass catcher using the frame han dle.

2. Remove grass catcher with clippings from under lawn

mower han dle.

3. Empty clippings from bag using both frame handle and

bag handle.

NOTE: Do not drag the bag when emptying; it will cause

unnecessary wear.

MOWING TIPS

CAUTION: Do not use de-thatcher

blade attachments on your mower.

Such attachments are hazardous, will

damage your mower and could void

your warranty.

• Under certain conditions, such as very tall grass, it

may be nec es sary to raise the height of cut to reduce

pushing effort and to keep from overloading the engine

and leaving clumps of grass clippings. It may also be

necessary to re duce ground speed and/or run the lawn

mower over the area a sec ond time.

• For extremely heavy cutting, re duce the width of cut

by over lap ping previously cut path and mow slowly.

• For better grass bagging and most cutting conditions,

the engine speed should be set in the FAST po si tion.

• When using a rear discharge lawn mower in moist,

heavy grass, clumps of cut grass may not enter the

grass catcher. Reduce ground speed (pushing speed)

and/or run the lawn mower over the area a second time.

• If a trail of clippings is left on the right side of a rear

discharge mow er, mow in a clockwise direction with a

small overlap to collect the clippings on the next pass.

• Pores in cloth grass catchers can become ﬁ lled with

dirt and dust with use and catchers will collect less

grass. To prevent this, reg u lar ly hose catcher off with

water and let dry before using.

• Keep top of engine around starter clear and clean of

grass clippings and chaff. This will help engine air ﬂ ow

and extend engine life.

OPERATION

MULCHING MOWING TIPS

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER

HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE

“CLEANING” IN THE MAINTENANCE SECTION OF THIS MANUAL.

• The special mulching blade will recut the grass clip-

pings many times and reduce them in size so that as

they fall onto the lawn they will disperse into the grass

and not be noticed. Also, the mulched grass will biode-

grade quickly to provide nutrients for the lawn. Always

mulch with your highest engine (blade) speed as this

will provide the best recutting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends

to form clumps and interferes with the mulching action.

The best time to mow your lawn is the early afternoon.

At this time the grass has dried, yet the newly cut area

will not be exposed to direct sunlight.

• For best results, adjust the lawn mower cutting height

so that the lawn mower cuts off only the top one-third

of the grass blades (See Fig. 12). If the lawn is over-

grown it will be necessary to raise the height of cut to

reduce pushing effort and to keep from overloading

the engine and leaving clumps of mulched grass. For

extremely heavy mulching, reduce your width of cut by

overlapping previously cut path and mow slowly.

FIG. 12

MAX 1/3

• Certain types of grass and grass conditions may require

that an area be mulched a second time to completely

hide the clippings. When doing a second cut, mow

across (perpendicular) to the ﬁ rst cut path.

• Change your cutting pattern from week to week. Mow

north to south one week then east to west the next week.

This will help prevent matting and graining of the lawn.

FUEL VALVE LEVER

( )

OFF

FIG. 11

OFF

CHOKE LEVER

LUBRICATION CHARTGENERAL RECOMMENDATIONS

The warranty on this lawn mower does not cover items that

have been subjected to operator abuse or negligence. To

receive full value from the warranty, operator must maintain

mower as instructed in this manual. Some adjustments

will need to be made periodically to properly maintain your

unit. At least once a season, check to see if you should

make any of the adjustments described in the Service and

Ad just ments section of this manual.

• At least once a year, replace the spark plug, clean or

replace air ﬁ lter element and check blade for wear. A

new spark plug and clean/new air ﬁ lter element assure

proper air-fuel mixture and help your engine run better

and last longer.

• Follow the maintenance schedule in this manual.

BEFORE EACH USE

1. Check engine oil level.

2. Check for loose fasteners.

LUBRICATION

Keep unit well lubricated (See “LUBRICATION CHART”).

IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL

BEARINGS. VISCOUS LU BRI CANTS WILL ATTRACT DUST

AND DIRT THAT WILL SHORT EN THE LIFE OF THE SELF-

LU BRI CAT ING BEARINGS. IF YOU FEEL THEY MUST BE

LU BRI CATED, USE ONLY A DRY, POW DERED GRAPHITE

TYPE LUBRICANT SPAR INGLY.

Check for Loose Fasteners

Clean / Inspect Grass Catcher *

Check Tires

Check Drive Wheels ***

Clean Lawn Mower ****

Clean under Drive Cover ***

Check Drive Belt / Pulleys ***

Check / Sharpen / Replace Blade

Lubrication

Clean and Recharge Battery **

Check Engine Oil level

Change Engine Oil

Clean Air Filter

Inspect Muffler

Replace Spark Plug

Replace Air Filter Paper Cartridge

Empty fuel system or add Stabilizer

BEFORE

EACH

USE

AFTER

EACH

USE

EVERY

HOURS

EVERY

25 HOURS

OR SEASON

EVERY

100

HOURS

BEFORE

STORAGE

1 - Change more often if operating under a heavy load or in high outdoor temperatures.

2 - Service more often if operating in dirty or dusty conditions.

3 - Replace blades more often when mowing in sandy soil.

4 - Charge 48 hours at end of season.

5 - And after each 5 hours of use.

(if so equipped)

Electric-Start mowers

Power-Propelled mowers

Use a scraper

to clean under deck

***

****

MAINTENANCE

ENGINE OIL

HANDLE BRACK ET MOUNT ING PINS

REAR DOOR HINGE

MULCHER

DOOR HINGE

SPRAY LUBRICANT

SEE “ENGINE” IN MAINTENANCE SECTION

LAWN MOWER

Always observe safety rules when performing any main-

te nance.

TIRES

• Keep tires free of gasoline, oil, or insect control chem-

i cals which can harm rubber.

• Avoid stumps, stones, deep ruts, sharp objects and

other hazards that may cause tire damage.

DRIVE WHEELS

Check wheels each time be fore you mow to be sure they

move freely.

The wheels not turning freely means trash, grass cuttings,

etc. are in the drive wheel or dust cover area and must be

cleaned to free drive wheels. If necessary to clean the

drive wheels, be sure to clean all wheels.

1. Remove hubcaps, locknuts and washers.

2. Remove wheels from wheel ad just ers.

3. Remove any trash or grass cuttings from inside the

dust cover, pinion and/or drive wheel gear teeth.

4. Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely,

contact a qualiﬁ ed service center.

BLADE CARE

For best results, mower blade must be kept sharp. Re place

bent or dam aged blades.

CAUTION: Use only a replacement blade

approved by the manufacturer of your

mower. Using a blade not approved

by the manufacturer of your mower is

hazardous, could damage your mower

and void your warranty.

TO REMOVE BLADE (See Fig. 13)

1. Disconnect spark plug wire from spark plug and place

wire where it cannot come in contact with plug.

2. Turn lawn mower on its side. Make sure air ﬁ lter and

carburetor are up.

3. Use a wood block between blade and mower hous ing

to prevent blade from turning when re mov ing blade

bolt.

NOTE: Protect your hands with gloves and/or wrap blade

with heavy cloth.

4. Remove blade bolt by turning counter-clockwise.

5. Remove blade and attaching hardware (bolt, lock

wash er and hardened wash er).

6. Remove debris shield.

NOTE: Remove the blade adapter and check the key inside

hub of blade adapter. The key must be in good condition

to work properly. Replace adapter if damaged.

TO REPLACE BLADE (See Fig. 13)

1. Position the blade adapter on the engine crank shaft.

Be sure key in adapter and crankshaft keyway are

aligned; and that the drive belt is inside the tab of the

belt retainer.

MAINTENANCE

2. Install debris shield.

3. Position blade on the blade adapter.

IMPORTANT: TO ENSURE PROPER AS SEM BLY, CENTER

HOLE IN BLADE MUST ALIGN WITH STAR ON BLADE

ADAPTER.

4. Be sure the trailing edge of blade (opposite sharp edge)

is up toward the engine.

5. Install the blade bolt with the lock washer and hardened

washer into blade adapter and crankshaft.

6. Use block of wood between blade and lawn mower hous-

ing and tighten the blade bolt, turning clockwise.

• The recommended tightening torque is 35–40 ft. lbs.

IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT

NEEDS REPLACING, REPLACE ONLY WITH APPROVED BOLT.

TO SHARPEN BLADE (See Fig. 14)

NOTE: We do not recommend sharp en ing blade - but if you

do, be sure the blade is balanced. An un bal anced blade

will cause eventual damage to lawn mower or engine.

• The blade can be sharp ened with a ﬁ le or on a grind-

ing wheel. Do not attempt to sharpen while on the

mower.

FIG. 14

CENTER HOLE

BLADE

5/8" BOLT OR PIN

FIG. 13

BLADE BOLT

HARDENED

WASHER

LOCK WASHER

TRAILING

EDGE

BLADE

ADAPTER

BELT RE-

TAINER

KEY

BLADE

CRANK-

SHAFT

KEY WAY

DEBRIS

SHIELD

MAINTENANCE

• To check blade balance, you will need a 5/8" diameter

steel bolt, pin, or a cone balancer. (When using a

cone bal anc er, follow the in struc tions supplied with

bal anc er.)

NOTE: Do not use a nail for balancing blade. The lobes of

the center hole may appear to be centered, but are not.

• Slide blade on to an unthreaded portion of the steel bolt

or pin and hold the bolt or pin parallel with the ground.

If blade is bal anced, it should remain in a horizontal

po si tion. If either end of the blade moves downward,

sharpen the heavy end until the blade is balanced.

GRASS CATCHER

• The grass catcher may be hosed with water, but must

be dry when used.

• Check your grass catcher often for damage or de te -

ri o ra tion. Through normal use it will wear. If catcher

needs replacing, replace only with ap proved replace-

ment catcher shown in the Repair Parts section of this

manual. Give the lawn mower model number when

ordering.

GEAR CASES

• To keep your drive system working properly, the gear

cases and area around the drive should be kept clean

and free of trash build-up. Clean under the drive cover

twice a season.

• The gear cases are ﬁ lled with lubricant to the proper level

at the factory. The only time the lubricant needs atten-

tion is if service has been performed on the gear case.

ENGINE

LUBRICATION

Maintenance, repair, or replacement of the emission control

devices and systems, which are being done at the custom-

ers expense, may be performed by any non-road engine

repair establishment or individual. Warranty repairs must

be performed by an authorized engine manufacturer’s

service outlet.

LUBRICATION

Use only high quality detergent oil rated with API service

classiﬁ cation SG–SL. Select the oil's SAE viscosity grade

according to your expected operating temperature.

CONTAINER

FIG. 15

NOTE: Multi-viscosity oils (5W30, 10W30 etc.) improve

starting in cold weather, and you should check your engine

oil level frequently to avoid possible engine damage from

running low on oil.

Change the oil after every 25 hours of operation or at least

once a year if the lawn mower is not used for 25 hours in

one year.

Check the crankcase oil level before starting the engine

and after each ﬁ ve (5) hours of continuous use. Tighten oil

plug securely each time you check the oil level.

4. Wipe off any spilled oil from lawn mower or side of

engine.

5. Fill engine with oil. Slowly pour oil down the oil ﬁ ll spout

into the engine.

6. Wait one minute to allow oil to settle. Use guage on oil

ﬁ ll cap/dipstick for checking level. Insert dipstick into

the tube and rest the oil ﬁ ll cap on the tube. DO NOT

thread the cap into the tube when taking reading.

7. Continue adding small amounts of oil and rechecking

the dipstick until it reads full. DO NOT overﬁ ll, or engine

will smoke on startup.

8. Always be sure to retighten oil ﬁ ll cap/dipstick before

starting engine.

9. Reconnect spark plug wire to spark plug.

LOWER MARK

FIG. 16

UPPER

MARK

OIL FILL CAP /

DIPSTICK

TO CHANGE ENGINE OIL (See Figs. 15 & 16)

NOTE: Before tipping lawn mower to drain oil, empty fuel

tank by running engine until fuel tank is empty.

1. Disconnect spark plug wire from spark plug and place

wire where it cannot come in contact with plug.

2. Remove oil ﬁ ll cap/dipstick; lay aside on a clean sur-

face.

3. Tip lawn mower on its side as shown and drain oil into

a suitable container. Rock lawn mower back and forth

to remove any oil trapped inside of engine.

AIR FILTER (See Fig. 17)

Your engine will not run properly and may be damaged by

using a dirty air ﬁ lter. Replace the air ﬁ lter every 100 hours of

operation or every season, whichever occurs ﬁ rst. Service

air cleaner more often under dusty conditions.

TO CLEAN AIR FILTER

1. Remove cover.

2. Carefully remove cartridge.

3. Clean by gently tapping on a ﬂ at surface. If very dirty,

replace cartridge.

CAUTION: Petroleum solvents, such as

ker o sene, are not to be used to clean

car tridge. They may cause de te ri o ra tion

of the cartridge. Do not oil car tridge.

Do not use pres sur ized air to clean or

dry car tridge.

4. Install cartridge, then replace cover.

FITTING

HOSE

FIG. 18

MUFFLER

Inspect and replace corroded mufﬂ er as it could create a

ﬁ re hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each mowing season

or after every 100 hours of operation, whichever occurs

ﬁ rst. Spark plug type and gap setting are shown in the

“PROD UCT SPEC I FI CA TIONS” section of this manual.

CLEANING

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER

HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN

THE UNDERSIDE OF YOUR MOWER AFTER EACH USE.

CAUTION: Disconnect spark plug wire

from spark plug and place wire where it

cannot come in contact with plug.

• Clean the underside of your lawn mower by scraping

to remove build-up of grass and trash.

MAINTENANCE

• Clean engine often to keep trash from accumulating. A

clogged engine runs hotter and shortens engine life.

• Keep ﬁ nished surfaces / wheels free of gasoline, oil, etc.

• We do not recommend using a garden hose to clean

lawn mower unless the electrical system, mufﬂ er, air

ﬁ lter and carburetor are covered to keep water out.

Water in engine can result in shortened engine life.

WATER WASHOUT FEATURE (See Fig. 18)

Your lawn mower is equipped with a ﬁ tting that allows quick

and easy cleaning of the underside of the housing. To use

this feature, proceed as follows:

1. Move lawn mower to an area of cut grass or another

hard surface.

NOTE: Water, grass and other debris will drain from beneath

the mower housing during the washout process.

2. Remove grass catcher and discharge chute assembly

from lawn mower.

3. Close mulcher door (if equipped).

4. Connect a garden hose to the ﬁ tting where shown.

IMPORTANT: BE SURE THE GARDEN HOSE IS NOT ROUTED

UNDER THE LAWN MOWER HOUSING OR ENTANGLED IN

THE WHEELS.

5. Turn on water supply and check for leaks at the ﬁ t-

ting.

If no leaks are present, start engine (as described in the

Operation section of this manual) and let engine run until

the underside of the lawn mower is clean.

WARNING: Do not engage the drive

system during the washout process.

6. Shut off the engine.

7. Shut off water supply and remove hose from ﬁ tting.

CAUTION: Do not remove hose from

ﬁ tting while engine is running. Water

in engine can result in shortened en-

gine life.

8. Start engine (as described in the Operation section

of this manual) and let engine run for a full minute to

remove excess water from mower.

FIG. 17

CARTRIDGE

SLOT

TAB

FILTER COVER

LAWN MOWER

TO ADJUST CUTTING HEIGHT

See “TO ADJUST CUTTING HEIGHT” in the Operation

section of this manual.

REAR DEFLECTOR

The rear deﬂ ector, attached between the rear wheels of

your mower, is provided to minimize the possibility that

objects will be thrown out of the rear of the mower into

the operator's mowing position. If the deﬂ ector becomes

damaged, it should be replaced.

CAUTION: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

1. Release control bar and stop engine.

2. Make sure the blade and all moving parts have completely stopped.

3. Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug.

SERVICE AND ADJUSTMENTS

TO REMOVE DRIVE BELT (See Figs. 19 & 20)

1. Turn lawn mower on its side with air ﬁ lter and car bu re-

tor up.

2. Remove blade bolt, lockwasher, hardened washer and

blade.

3. Remove debris shield.

4. Remove side bumper.

5. Remove rear bafﬂ e.

6. Disconnect return spring from rear bafﬂ e / rear gearcase

belt keeper.

7. Disconnect cable from rear gearcase.

FRONT

BAFFLE

DRIVE

COVER

SIDE

BUMPER

BLADE BOLT

HARDENED WASHER

LOCKWASHER

BLADE

DEBRIS

SHIELD

REAR

BAFFLE

FIG. 19

SERVICE AND ADJUSTMENTS

8. Remove front bafﬂ e.

9. Remove drive cover.

10. Remove front belt keeper.

11. Remove belt from front gearcase pulley.

12. Remove all three idler pulleys from idler assembly.

13. Remove belt from blade adapter/engine pulley and

idler assembly.

14. Remove rear gearcase pulley by clamping locking

pliars to input shaft (beneath pulley) and loosening

pulley with a 9/16" box wrench.

15. Remove old belt from mower and discard.

TO REPLACE DRIVE BELT (See Figs. 19 & 20)

NOTE: Always use factory approved belt to assure proper

ﬁ t and long life.

1. Place new belt on rear gearcase pulley. Be sure the

new belt is inside the tabs of the belt keeper.

2. Reinstall rear gearcase pulley.

3. Route the other end of the new belt through hole in

housing to front gearcase pulley.

4. Route new belt through idler assembly to blade adapter/

engine pulley.

5. Reinstall all three idler pulleys.

6. Position the blade adapter/engine pulley on the engine

crank shaft. Be sure key in blade adapter/engine pulley

and crankshaft keyway are aligned; and that the new

belt is inside the tab of the belt retainer.

7. Install new belt on front gearcase pulley.

8. Reinstall front belt keeper. Be sure the new belt is

inside the front belt keeper.

9. Reinstall drive cover.

10. Reinstall front bafﬂ e.

11. Reattach cable to rear gearcase.

12. Reattach return spring to rear bafﬂ e / rear gearcase

belt keeper.

13. Reinstall rear bafﬂ e.

14. Reinstall side bumper.

15. Reinstall debris shield.

16. Reinstall blade. The recommended tightening torque

is 35–40 ft. lbs.

17. Return mower to upright po si tion.

18. Reattach spark plug wire to spark plug.

FIG. 20

FRONT BELT

KEEPER

BELT

TABS

FRONT

REAR

GEARCASE

PULLEY

RETURN

SPRING

CABLE

CRANK-

SHAFT

KEYWAY

IDLER

PULLEYS

BELT

RETAINER

BLADE ADAPTER /

ENGINE PULLEY

KEY

IDLER

ASSEMBLY

REAR

GEARCASE

BELT

KEEPER

FRONT

GEARCASE

PULLEY

INPUT

SHAFT

SERVICE AND ADJUSTMENTS

ENGINE

Maintenance, re pair, or re place ment of the emission con-

trol de vic es and sys tems, which are be ing done at the

cus tom ers expense, may be performed by any non-road

engine repair es tab lish ment or individual. Warranty repairs

must be performed by an authorized engine man u fac tur er's

service outlet.

ENGINE SPEED

Your engine speed has been factory set. Do not attempt to

increase engine speed or it may result in personal injury. If

you believe that the engine is running too fast or too slow,

take your lawn mower to an authorized service center for

repair and adjustment.

CARBURETOR

Your carburetor is not adjustable. If your engine does not

operate properly due to suspected carburetor problems,

take your lawn mower to an authorized service center for

repair and/or adjustment.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR,

WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.

OVER SPEED ING THE ENGINE ABOVE THE FACTORY HIGH

SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE

ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,

CONTACT YOUR NEAREST AUTHORIZED SER VICE CEN TER,

WHICH HAS PROPER EQUIP MENT AND EXPERIENCE TO

MAKE ANY NEC ES SARY ADJUSTMENTS.

STORAGE

Immediately prepare your mower for storage at the end of the season or if the unit will not be used for 30 days or more.

HANDLE (See Figs. 22 and 23)

You can fold your lawn mower han dle for storage.

1. Loosen the two (2) handle knobs on sides of the upper

handle and allow handle to fold down to the rear.

2. Remove the two (2) handle knobs and carriage bolts

on sides of the lower handle and pivot entire handle

as sem bly forward and allow it to rest on mower.

3. Reinstall knobs and carriage bolts to lower handle or

handle brackets for safe keeping.

• When setting up your handle from the storage position,

the lower han dle will require manually locking into the

mowing position.

IMPORTANT: WHEN FOLDING THE HANDLE FOR STORAGE

OR TRANSPORTATION, BE SURE TO FOLD THE HANDLE AS

SHOWN OR YOU MAY DAMAGE THE CONTROL CABLES.

LAWN MOWER

When lawn mower is to be stored for a period of time, clean

it thoroughly, remove all dirt, grease, leaves, etc. Store in

a clean, dry area.

1. Clean entire lawn mower (See “CLEANING” in the

Maintenance section of this manual).

2. Lubricate as shown in the Maintenance section of this

manual.

3. Be sure that all nuts, bolts, screws, and pins are securely

fastened. Inspect moving parts for damage, breakage

and wear. Replace if necessary.

4. Touch up all rusted or chipped paint surfaces; sand

lightly before painting.

TO ADJUST HANDLE (See Fig. 21)

The handle on your lawn mower has three (3) height posi-

tions - adjust to height that suits you.

1. Remove knob and carriage bolt on one side of the

lower handle.

2. While holding handle assembly, remove knob and

car riage bolt from opposite side, align hole in handle

with desired hole in handle bracket and reassemble

bolt and knob and tighten securely.

3. Align opposite side of handle with same positioning

hole and secure with bolt and knob.

FIG. 21

HANDLE

BRACKET

BOLT

KNOB

HIGH

MEDIUM

LOW

STORAGE

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS

FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS

SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR

TANK DURING STORAGE. ALCOHOL BLENDED FUELS

(CALLED GASOHOL OR USING ETHANOL OR METHANOL)

CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION

AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS

CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN

STORAGE.

• Empty the fuel tank by starting the engine and letting

it run until the fuel lines and carburetor are empty.

• Never use engine or carburetor cleaner products in the

fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini-

mizing the formation of fuel gum deposits during stor age.

Add stabilizer to gasoline in fuel tank or storage container.

Always follow the mix ratio found on stabilizer container.

Run engine at least 10 minutes after adding stabilizer to

allow the stabilizer to reach the carburetor. Do not empty

the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en-

gine oil. (See “ENGINE” in the Maintenance section of

this manual).

CYLINDER

1. Remove spark plug.

2. Pour one ounce (29 ml) of oil through spark plug hole

into cylinder.

3. Pull starter handle slowly a few times to distribute oil.

4. Replace with new spark plug.

OTHER

• Do not store gasoline from one season to another.

• Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

• If possible, store your unit indoors and cover it to give

protection from dust and dirt.

• Cover your unit with a suitable protective cover that

does not retain moisture. Do not use plastic. Plastic

cannot breathe, which allows condensation to form and

will cause your unit to rust.

IMPORTANT: NEVER COVER MOWER WHILE ENGINE AND

EXHAUST AREAS ARE STILL WARM.

CAUTION: Never store the lawn mower

with gasoline in the tank inside a build-

ing where fumes may reach an open

ﬂ ame or spark. Allow the engine to cool

before storing in any enclosure.

FIG. 22

MOWING

POSITION

OPERATOR

PRES ENCE

CONTROL

BAR

FOLD

FORWARD

FOR

STORAGE

LOWER

HANDLE

KNOB

UPPER

HANDLE

FIG. 23

HANDLE

BRACKET

BOLT

KNOB

TROUBLESHOOTING POINTS

Does not start 1. Dirty air ﬁ lter. 1. Clean/replace air ﬁ lter.

2. Out of fuel. 2. Fill fuel tank.

3. Stale fuel. 3. Empty fuel tank and reﬁ ll tank with fresh,

clean gasoline.

4. Water in fuel. 4. Empty fuel tank and reﬁ ll tank with fresh,

clean gasoline.

5. Spark plug wire is disconnected. 5. Connect wire to plug.

6. Bad spark plug. 6. Replace spark plug.

7. Loose blade or broken blade adapter. 7. Tight en blade bolt or replace blade adapter.

8. Control bar in released position. 8. Depress control bar to handle.

9. Control bar defective. 9. Replace control bar.

10. Fuel valve lever (if equipped) in OFF position. 10. Turn fuel valve lever to the ON position.

11. Weak battery (if equipped). 11. Charge battery.

12. Disconnected battery connector (if equipped). 12. Connect battery to engine.

Loss of power 1. Rear of lawn mower housing or cutting 1. Raise cutting height.

blade dragging in heavy grass.

2. Cutting too much grass. 2. Raise cutting height.

3. Dirty air ﬁ lter. 3. Clean/replace air ﬁ lter.

4. Buildup of grass, leaves and trash under 4. Clean underside of mower housing.

mower.

5. Too much oil in engine. 5. Check oil level.

6. Walking speed too fast. 6. Cut at slower walking speed.

Poor cut – 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.

uneven 2. Wheel heights uneven. 2. Set all wheels at same height.

3. Buildup of grass, leaves and trash under 3. Clean underside of mower housing.

mower.

Excessive 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.

vibration 2. Bent engine crankshaft. 2. Contact a qualiﬁ ed service center.

Starter rope 1. Engine ﬂ ywheel brake is on when control 1. Depress control bar to upper handle before

hard to pull bar is released. pulling starter rope.

2. Bent engine crankshaft. 2. Contact a qualiﬁ ed service center.

3. Blade adapter broken. 3. Replace blade adapter.

4. Blade dragging in grass. 4. Move lawn mower to cut grass or other

hard surface before starting.

Grass catcher 1. Cutting height too low. 1. Raise cutting height.

not ﬁ lling 2. Lift on blade worn off. 2. Replace blade.

(if so equipped) 3. Catcher not venting air. 3. Clean grass catcher.

Hard to push 1. Grass is too high or wheel height is too low. 1. Raise cutting height.

2. Rear of lawn mower housing or cutting 2. Raise rear of lawn mower housing one (1)

blade dragging in heavy grass. setting higher.

3. Grass catcher too full. 3. Empty grass catcher.

4. Handle height position not right for you. 4. Adjust handle height to suit.

Loss of drive 1. Belt wear. 1. Check/replace drive belt.

(or slowing of 2. Belt off of pulley. 2. Check/reinstall drive belt.

drive speed) 3. Drive cable worn or broken. 3. Put belt on pulleys / replace belts if broken.

4. “Loose” drive control system. 4. Adjust drive control.

PROBLEM CAUSE CORRECTION

Consumer Wheeled Products - Limited Warranty

Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanship under normal use

and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. This Limited Warranty may not be transferred

to any subsequent purchaser of this Husqvarna® product. Certain components (e.g., engines and transmissions) are excluded from coverage, and other

limitations apply, as described in this document. Husqvarna will repair or replace at its discretion, any defective product or part covered by the Limited

Warranty, free of charge at any authorized Husqvarna Servicing Dealer/Center using original OEM Husqvarna replacement parts, subject to the

limitations and exclusions described below. Husqvarna does not offer an over-the-counter exchange program.

DISCLAIMERS, LIMITATIONS AND EXCLUSIONS

1. WARRANTY DISCLAIMER. THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY PROVIDED BY HUSQVARNA AND THERE ARE NO

WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF, EXCEPT AS MAY BE PROVIDED BY LAW. THIS WARRANTY IS

GIVEN ONLY BY HUSQVARNA, AND MAY BE MODIFIED ONLY BY HUSQVARNA. THIS LIMITED WARRANTY IS THE FINAL EXPRESSION OF OUR

AGREEMENT, AND IS A COMPLETE AND EXCLUSIVE STATEMENT OF THE TERMS OF THAT AGREEMENT. THIS LIMITED WARRANTY GIVES YOU

SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY BASED ON LOCALITY

2. LIMITED DURATION. ANY WARRANTY THAT MAY BE IMPLIED BY LAW (INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE OR USE AND IMPLIED WARRANTY OF MERCHANTABILITY) IS LIMITED TO THE DURATION OF THE APPLICABLE

WARRANTY PERIOD UNDER THIS LIMITED WARRANTY. SOME LOCALITIES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED

WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

3. EXCLUSIVE REMEDIES. SOME LOCALITIES, INCLUDING THE PROVINCE OF QUEBEC, DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

LIABILITY FOR INJURY TO PERSON OR FOR DAMAGES RESULTING FROM THE FAULT OF THE MANUFACTURER AND/OR THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. AS SUCH, SOME OF THE FOLLOWING LIMITATIONS MAY NOT APPLY TO YOU. THE

ABOVE REMEDIES ARE THE EXCLUSIVE REMEDIES FOR ANY BREACH OF THIS LIMITED WARRANTY. NO OTHER REMEDY, INCLUDING, BUT NOT

LIMITED TO ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES, FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR

PROPERTY, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS SHALL BE AVAILABLE, AND ALL SUCH DAMAGES ARE HEREBY

DISCLAIMED.

4. Engines, Transmissions and certain other components are NOT covered. This Limited Warranty does not cover any of the following:

(a) Engines and Attachments.Except where otherwise indicated on Exhibit A, all Engines and Attachments are not covered by this Limited Warranty. In most cases, these

items are NOT manufactured by Husqvarna in which case they may be covered separately by their respective manufacturer's warranties if one is provided and included with

the product at the time of purchase. All such claims must be submitted and sent to the appropriate manufacturer or as otherwise directed in those separate warranties.

Husqvarna is not authorized to handle warranty adjustments or repairs on engines manufactured by Briggs & Stratton, Honda, Kawasaki, or Kohler (with the exception of

models equipped with LCT engines). Husqvarna does not assume any warranty obligation of the other manufacturers' engines under this Limited Warranty.

(b) Transmissions. Except where otherwise indicated on ExhibitA, Transmission / Transaxle (including Drive Systems) are not covered by this Limited Warranty. In most

cases, these items are NOT manufactured by Husqvarna in which case they may be covered separately by their respective manufacturer's warranties if one is provided and

included with the product at the time of purchase. The following transmission / transaxle manufacturers, Dana, Hydro-Gear, Tuff-Torq provide a warranty for the

transmission / transaxle to the ultimate purchaser or to Husqvarna. Husqvarna will assign the transmission / transaxle manufacturer's warranty or any rights thereof to the

original purchaser of the unit. To obtain transmission / transaxle warranty service, first contact the retailer who you purchased the unit from. Should you require assistance

or have any questions concerning transmission / transaxle warranty coverage, contact Husqvarna directly at our website www.husqvarna.com or call 800-487-5951 (US) or

800-805-5523 (Canada) for an authorized Husqvarna service provider. All such claims must be submitted and sent to the appropriate manufacturer or as otherwise directed

in those separate warranties. Husqvarna is not authorized to handle warranty adjustments or repairs on transmissions or transaxles. Husqvarna does not assume any

obligations under this Limited Warranty for the above listed manufacturers (for exceptions - see Exhibit A).

(c) Expendable Parts. This Limited Warranty does not cover general maintenance parts and items ("Expendable Parts"), including without limitation spark plugs, bulbs,

filters, lubricants, starter cords, belts, blades, and blade adapters.

(d) Emissions Control Components. This Limited Warranty does not cover Emissions control equipment and components to the extent regulated by the U.S. Environmental

Protection Agency or similar state, provincial or federal agencies. Such equipment and components are covered by a separate emission control warranty statement supplied

with your new product. Please consult this separate warranty statement for details.

5. Any COMMERCIAL, INSTITUTIONAL, AGRICULTURAL, INDUSTRIAL, INCOME PRODUCING, or RENTAL use will result in either

No Warranty or a Shortened Warranty Period. Depending on the product, there is either NO WARRANTY (whether statutory, contractual or

otherwise) or a reduced warranty if the product is used for commercial, institutional, agricultural, industrial, income producing, or rental purposes and, in

such circumstances, this Limited Warranty is offered instead of and replaces any warranty regime provided for by law. Please refer to Exhibit A.

6. Reconditioned or Refurbished Products have a 30 Day Limited Warranty. Under this Limited Warranty, Certified Factory Reconditioned or

Refurbished products have a 30 Day Limited Warranty for parts and labor for Non-Commercial Use. Products are only reconditioned at the Husqvarna

Factory.

7. Owner's (Your) Responsibilities. To preserve your rights under this Limited Warranty, you must exercise reasonable care and use of the product,

including, following the preventative maintenance, storage, fuel and oil usages as prescribed in the enclosed operator's manual. For example, the

following items are the Owner's responsibility and are not covered by this Limited Warranty:

a. Set-up and pre-delivery service, and engine tune-ups;

b. Adjustments after the first (30) thirty days of purchase and beyond, such as throttle cable, belt guides adjustments; and

c. Preventative maintenance as outlined in the operator's manual.

In addition, you must cease using the product immediately upon any failure or damage. The product should be taken to an authorized Husqvarna

servicing dealer prior to any further use.

8. Damages resulting from normal aging, wear and tear or neglect are NOT covered. The Limited Warranty does not cover damage other than

that resulting from defects in material or workmanship. The following are NOT considered defects in material or workmanship, and therefore are NOT

covered.

(a) Abrasion to mower decks;

(b) Tires damaged by external punctures;

(d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures;

In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including

any of the following:

(e) Failure to provide or perform required maintenance services as prescribed in the operator's manual;

(f) Abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, use of unauthorized attachments, Lack of lubrication or

engine failure, due to the use of oils that do not meet Engine manufacturer's specifications;

(g) Use of gasohol, containing methanol (wood alcohol). Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE

(methyl/tertiary/butyl/ether) is approved;

(h) Use of ether or any starting fluids;

(i) Pressure cleaning or steam cleaning the product;

(j) Use of spark plugs other than those meeting emission performance requirements listed in the operator's manual;

(k) Tampering with engine speed governor or emission components, or running engines above specified and recommended engine speeds as

listed in your operator's manual;

(l) Operation of the unit with improperly installed/removed or modified cutting shields, guards, or safety devices;

(m) Any removed/damaged air filter, excessive dirt, abrasives, salt water, moisture, corrosion, rust, varnish, stale fuel, or any adverse reaction due

to incorrect storage procedures;

(n) Failures due to improper set up, pre-delivery service or repair service by anyone other than an authorized Husqvarna servicing dealer during

the warranty period;

(o) Dirt contaminated grease or oil, use of incorrect type of greases or oils, failure to comply with recommended greasing intervals, water or

moisture damage, and/or improper storage;

(p) Sprayers pumping or spraying caustic or flammable materials, lack of or broken strainers; or

(q) Continued use of product, after initial operational problem or failure occurs.

9. Reinforced Stamped (Armor Protected) 10 Year Limited & Fabricated Limited Lifetime, Deck Warranties. These Limited Warranties are for

the deck shell only – mechanical components/parts such as belts, pulleys, spindle housings, bearings, blades, rods, height adjusters, caster/anti scalp

wheels etc… are NOT covered. The Limited Lifetime Warranty does not cover damage other than that resulting from defects in material or

workmanship. The following are NOT considered defects in material or workmanship, and therefore are NOT covered:

(a) Abrasion to mower decks, including sand wear;

(b) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures;

(d) Natural discoloration of paint or other materials due to ultraviolet light.

HOW TO OBTAIN SERVICE

10. Authorized Husqvarna Servicing Dealer/Center. In order to obtain warranty coverage it is your responsibility (at your expense) to deliver or ship

your Husqvarna unit to an authorized Husqvarna Servicing Dealer/Center and arrange for pick-up or return of your unit after the repairs have been made.

If you do not know the location of your nearest authorized Husqvarna Servicing Dealer, call Husqvarna, at 1-800-487-5951 during the hours of 8:00 AM