Comtrend PG-9182AC Mode d'emploi

Catégorie
Adaptateurs réseau PowerLine
Taper
Mode d'emploi
Page
Page 1
Reset Button
Press for more
than 10 seconds
for Factory Reset
Security Button
Enables Device
Synchronization in
Secure Mode
ON/OF WiFi Button
Turns the WiFi
On and Off
WPS Button
Enables
WPS
Synchronization
Ethernet Port
LED Icons
Descriptions are
provided on the
following page
Quick Install Guide
PG-9182AC G.hn 2000 Powerline Adapter with WiFi
Understanding Your Powerline Adapter
A
Page
Page 2
LED
Color
Mode
Description
Power LED
Green
On
The Adapter is powered on.
Off
Off
The Adapter is powered off or faulty.
Connection
LED
Green
On
The current connection (line rate) is more
than 40Mbps.
Orange
On
The current connection (line rate) is
between 5Mbps and 40Mbps.
Red
On
The current connection (line rate) is less
than 5Mbps.
Off
Off
An Adapter connection does not exist.
Security LED
Green
On
The Adapter is secure (it has received or
generated network keys).
Blinking
The Adapter is in the process of being
secure.
Off
Off
The Adapter is not secure.
2.4GHz LED
Green
On
2.4GHz WLAN is on.
Off
Off
2.4GHz WLAN is off.
5GHz LED
Green
On
5GHz WLAN is on.
Off
Off
5GHz WLAN is off.
WPS LED
Green
On
WPS is enabled.
Green
Blinking
A WPS connection is in process.
Off
Off
WPS is not enabled.
Etherent
LED
Green
On
An Ethernet LAN connection is
established.
Blinking
Data over the Ethernet LAN connection is
being transmitted.
Off
Off
An Ethernet LAN connection is not
established.
Page
Page 3
Initial Powerline Adapter Setup
NOTE: A minimum of two G.hn Powerline Adapters are required. We
suggest using the PG-9182PT as the primary Adapter that connects to
your Network Device (Modem, Router, Access Point).
à
If you are setting up a G.hn Powerline network for the first time,
then follow the below steps starting at Step 1.
à
If you are adding to an existing G.hn Powerline network, then skip
to Steps 3-4.
1. Plug the PG-9182PT* Powerline Adapter into a power
outlet near your Network Device (Modem, Router, or
Access Point).
*We sugguest using a PG-9182PT as the primary
Adapter that connects to your Network Device,
however, you can use any G.hn Powerline Adapter.
For maximum performance, please plug the
Powerline Adapter directly into the wall outlet. Do not
plug into a power strip or surge protector, as network
performance could degrade significantly.
2. Connect the PG-9182PT to
your Network Device
(Modem, Router, or Access
Point) with an Ethernet
(RJ-45) cable. Wait 10
seconds for the Ethernet LED
to light up GREEN, which
indicates a connection is
established. A flashing
GREEN light indicates that
the device is sending data.
B
PG-9182PT
Page
Page 4
3. Plug the PG-9182AC Powerline Adapter into a
power outlet near the location you want to add
Wireless.
Pairing the Powerline Adapters
4. Press the Security Button on one Adapter until you see the Security
LED start blinking GREEN. Then press the Security Button on the
other Adapter until you see the Security LED start blinking
GREEN. The Security LED and the Connection LED should
be solid GREEN on both Adapters when they are successfully
paired.
Note: If you are adding to an existing G.hn Powerline network, then press the
Security Button on any Adapter in the existing G.hn Powerline network until
you see the Security LED start blinking GREEN. Repeat this on the
Powerline Adapter you are adding. The Security LED and the Connection
LED will light up GREEN on all adapters within the G.hn Powerline network.
5. Repeat Steps 3 to 4 to add additional Powerline Adapters. Please
note that up to 16 devices can be connected within a Powerline
G.hn Network.
Network Device
(Modem, Router, or
Access Point)
Smart TV
Network Device
(Modem, Router, or
Access Point)
C
PG-9182AC
Page
Page 5
Connect Your WiFi Devices to the New PG-9182AC
Access Point
Note: The WiFi network behavior can vary based on different
deployment scenarios. If WifiXtend™ or HARMONY technologies are
being utilized, then the WiFi network will automatically become a
single network with one SSID and Password per band. This occurs when
there are two or more PG-9182AC adapters being used/when the
Gateway is a WifiXtend™ or HARMONY enabled Comtrend Gateway.
6. For some devices (E.g. laptops,
cameras, set-top-boxes, etc.)
Wireless connectivity can be done
via WPS (Wireless Protected Setup).
WPS allows you to simply connect
devices to the new Access Point
without entering a
username/password manually. To do
this, please follow the instructions in
Section E below.
7. To connect your WiFi devices to your
new PG-9182AC WiFi Access Point,
select the PG-9182AC Access Point
using your WiFi device’s standard
network list. The Network Name (SSID)
and Password (WiFi Key) can be
found on the bottom of the
PG-9182AC.
8. Go to Section G.
Setup of WiFi Devices via WPS (WiFi Protected Setup)
D
E
Page
Page 6
10. Press and hold the WPS Button for more than 2
seconds on the PG-9182AC to activate its WPS. The
PG-9182AC’s WPS LED should blink GREEN to
indicate a WPS connection is in progress.
11. Within two minutes, press the WPS Button (often the
WPS/Reset Button) on your remote Internet-Enabled
Devices to activate WPS.
12. The devices will establish a secure WiFi connection.
You Have Succesfully Set Up Your G.hn Powerline Adapter
with WiFi!
Creating a Custom SSID & Password
13. If you would like a different SSID and Password than what is provided,
you will need to change it via the Web management interface. Start
your Web browser and input “192.168.0.10” in the address bar. Then
press the “Enter” key.
14. You will then see the following
displayed. Input the Username
“root” and default password “1234”.
Then press the Login button to view
the Web management interface.
G
F
Page
Page 7
15. Press the “Wireless Settings”
section in the left-hand
sidebar. Here you can adjust
the SSID for the two Wireless
bands.
16. Press the “Security Settings”
section to adjust the Wireless
security settings for the wireless
bands.
Troubleshooting
The following information should help you diagrnose basic set up or installation problems.
Connection LED is OFF: The Connection LED shows that the Powerline Adapter is
connected to the G.hn Network. If the indicator is off, then plug both Powerline
Adapters that you are attempting to pair into power outlets that are located within the
same room. The Connection LED should light up GREEN. If not, then press the Reset
Button on each adapter for more than 10 seconds. Afterwards, you can plug the units
back into their original location.
Ethernet LED is OFF: If the Ethernet LED fails to light up, check that the LAN port of the
Powerline Adapter is connected firmly to the LAN port of the other device. To check the
condition of the Ethernet cable, use another cable to test the same connection.
Security LED is OFF: If the Security LED is off, then it means the Powerline Adapter is not
securely paired. Press the Security Button on the Powerline Adapter for 3 seconds until
you see the Security LED start flashing GREEN. Repeat this on the other Powerline
Adapter. The Security LED and the Connection LED will light up GREEN on both adapters.
This means the adapters are now securely paired and have a strong connection.
2.4GHz LED /5GHz LED is OFF: If the 2.4GHz LED/5GHz LED are off, then it means
the WiFi is not enabled. You can turn on both indicators, (i.e. enable WiFi) by pressing
the WiFi Button on the side of the device. You can also login to the PG-9182AC
Web Interface to enable the WiFi. Please refer to the User Manual for additional details.
To join an existing G.hn Powerline network, press the Security Button on any Powerline
Adapter in the existing G.hn Powerline network for 3 seconds until you see the Security
LED start flashing GREEN. Then press the Security Button on the additional Powerline
Adapter. The Security LED and the Connection LED will light up GREEN on both adapters.
*If you have tried the above and are still experiencing problems, you can reset all devices to
H
Page
Page 8
factory default by pushing the Reset Button for more than 10 seconds (until all the LEDs of the
device blink).
Power Specifications:
I/P: 100-240Vac, 50/60Hz, 15A
O/P: 100-240Vac, 50/60Hz, 15A
WARNING
For indoor use only
Disconnect the PLC from the power source before servicing
Do NOT open the casing
Do NOT use near water
Do NOT insert sharp objects into the adapter’s socket
Socket maximum output is 15A
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20 cm between the radiator and your body.
Caution: Exposure to Radio Frequency Radiation.
1. To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.
2. To comply with RSS 102 RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained
between the antenna of this device and all persons.
Attention: exposition au rayonnement radiofréquence.
1. Pour se conformer aux exigences de conformité RF canadienne l'exposition, cet appareil et son antenne ne doivent pas être
co-localisés ou fonctionnant en conjonction avec une autre antenne ou transmetteur.
2. Pour se conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d'au moins 20 cm doit être
maintenue entre l'antenne de cet appareil et toutes les personnes.
Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile
satellite systems.
La bande 5 150-5 250 MHz est réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
FOR MORE HELP: For instructions on advanced features, FAQ, etc., please visit the PG-9182AC
online Product Webpage on our website.
For more information:
YouTube: https://www.youtube.com/user/ComtrendConnection
Facebook: https://facebook.com/Comtrend
Website: http://us.comtrend.com/
Support: Visit our website or call (949) 753-9640
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Comtrend PG-9182AC Mode d'emploi

Catégorie
Adaptateurs réseau PowerLine
Taper
Mode d'emploi

dans d''autres langues