Used in this guide.
Artículos utilizados en este manual / Utilisé dans ce guide / In
dieser Gebrauchsanweisung verwendete Bezeichnungen /
Usato in questa guida / Gebruikt in deze handleiding / Används i
den här handboken.
Important safety information.
Please read this and the online guide(s) at
support.aeotec.com/ths carefully. Failure to follow the
recommendations set forth by Aeotec Limited may be
dangerous or cause a violation of the law. The
manufacturer, importer, distributor, and / or reseller will
not be held responsible for any loss or damage resulting
from not following any instructions in this guide or in
other materials. Use this equipment only for its intended
purpose. Follow the disposal instructions. Do not
dispose of electronic equipment or batteries in a fire or
near open heat sources.
aërQ Temperature & Humidity Sensor is intended for
indoor use in dry locations only. Do not use in locations
with direct water contact.
Contains small parts; keep away from children.
Quick start.
The following will step you through installing aërQ
Temperature & Humidity Sensor and connecting it to
your Z-WaveTM network.
1. Remove the battery insulation strip from your aërQ
Temperature & Humidity Sensor.
2. Add aërQ Temperature & Humidity Sensor to your
Z-Wave network;
a. If your Z-Wave gateway supports SmartStart:
scan the QR code on aërQ Temperature &
Humidity Sensor using the gateway’s app. Your
sensor will join your Z-Wave network
automatically.
b. If your gateway does not support SmartStart;
i. Set your Z-Wave gateway into its ‘add device’
mode. Refer to the gateway’s manual if you
are unsure of how to perform this step.
ii. Press the sensor’s button 3 times within 1.5
seconds; it is located on the top middle
section of this device.
iii. When aërQ Temperature & Humidity Sensor
is joining your Z-Wave network, its LED will
blink green and red.
iv. If pairing is successful, your sensor’s LED will
change to a green colour for 3 seconds
aërQ Temperature &
Humidity Sensor
ZWA009
PIN: 123456
SN: 201808
Note: QR Code used for SmartStart inclusion.
DSK Code can be found on packaging. Do not
remove or damage them.
Remarque: code QR utilisés pour l'inclusion
SmartStart. Le code DSK peut être trouvé sur
l'emballage. Ne les enlevez pas et ne les
endommagez pas.
Hinweis: Der QR-Code wird für die
SmartStart-Einbindung verwendet. Der DSK-Code
ist auf der Verpackung zu finden. Entfernen oder
beschädigen Sie diesen nicht.
Action Button
Botón de acción /
Bouton d'action /
Aktionstaste / Pulsante
di azione / Actieknop /
Action Button
Double-sided Tape
for Magnet
In Europe contact Aeotec Group GmbH; Große Johannisstraße 7,
20457 Hamburg, Germany.
FCC ID: 2AOGIZWA009
© & ™ Aeotec Limited. Version: 501000900001 - AA
www.aeotec.com
before turning off. If pairing failed, your
sensor’s LED will flash red 3 times; repeat the
step or contact us for further support if
needed.
3. After connecting aërQ Temperature & Humidity
Sensor to your gateway, test it in your chosen
installation location by pressing the action button. If
its LED briefly blinks green, it has a good
connection to your gateway. Place or affix it in
place using the included adhesive.
The aërQ Temperature & Humidity Sensor is now a
part of your Z-Wave home control system. You can
configure it and its automations via your Z-Wave
system; please refer to your software’s user guide for
precise instructions.
Get help & learn more.
Should you encounter any problem with aërQ
Temperature & Humidity Sensor, visit
support.aeotec.com/ths or contact our support team
via aeotec.com/contact. You can also learn more about
your sensor’s features, configuration options, and
technical specifications at the link.
Gateway compatibility.
To see if your sensor is known to be compatible with
your Z-Wave gateway, please refer to
aeotec.com/z-wave-gateways.
Declaration of Conformity. Aeotec Limited declares that
ZWA009 is in compliance with the essential requirements and
other relevant provisions of RED 2014/53/EU, RoHS 2011/65/EU,
IEC62321:2008 and EN50581:2012. The full text of the
declaration is available from support.aeotec.com/ths/doc
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.
-
1
-
2
-
3
