Oregon Scientific CS250 Original Instruction Manual

AF 0513 - F/N 547361

ORIGINAL INSTRUCTION MANUAL

CHAIN SAW MODEL CS250

MANUEL D’INSTRUCTION ORIGINAL

TRONÇONNEUSE MODÈLECS250

MANUAL DE INSTRUCCIONES ORIGINAL

MOTOSIERRA MODELO CS250

1

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

AF 0513  F/N 547361

ENGLISH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

WARNING: READ AND UNDERSTAND ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. FAILURE TO FOLLOW

THE WARNINGS AND INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR SERIOUS INJURY.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.

FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

AVERTISSEMENT: VEUILLEZ LIRE ET COMPRENDRE TOUS LES AVERTISSEMENTS DE SÉCURITÉ ET TOUTES

LES INSTRUCTIONS. LE NON-RESPECT DES AVERTISSEMENTS DE SÉCURITÉ ET DES INSTRUCTIONS PEUT ENTRAÎNER

UNE DÉCHARGE ÉLECTRIQUE, UN INCENDIE ET/OU DES BLESSURES GRAVES.

CONSERVEZ L’ENSEMBLE DES AVERTISSEMENTS ET INSTRUCTIONS POUR RÉFÉRENCE ULTÉRIEURE.

ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

ADVERTENCIA: LEA Y COMPRENDA TODAS LAS ADVERTENCIAS DE SEGURIDAD Y TODAS LAS INSTRUCCIONES.

NO SEGUIR LAS ADVERTENCIAS Y LAS INSTRUCCIONES PUEDE PROVOCAR CHOQUES ELÉCTRICOS, INCENDIOS Y/O

LESIONES GRAVES.

CONSERVE TODAS LAS ADVERTENCIAS E INSTRUCCIONES COMO REFERENCIA PARA EL FUTURO.

2

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

TABLE OF CONTENTS

AF 0513  F/N 547361

TABLE OF CONTENTS

SYMBOLS AND LABELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

GENERAL POWER TOOL SAFETY WARNINGS. . . . . . . . . . . . .4

WORK AREA SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ELECTRICAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PERSONAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CHAIN SAW SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . 7

STORAGE, TRANSPORTING, AND DISPOSAL . . . . . . . . . . . . . 9

BATTERY SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

CHARGER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

PRODUCT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

SPECIFICATIONS AND COMPONENTS . . . . . . . . . . . . . . . . . . . . 13

CHAIN SAW NAMES AND TERMS. . . . . . . . . . . . . . . . . . . . . . . . 14

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

FILLING OIL RESERVOIR . . . . . . . . . . . . . . . . . . . . . . . . . . 15

OPERATING THE SAW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

BATTERY PACK AND CHARGER . . . . . . . . . . . . . . . . . . . . . 16

GENERAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

CUTTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SHARPENING WITH POWERSHARP®. . . . . . . . . . . . . . . . . . . . . . 22

MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . 23

REPLACING THE BAR AND CHAIN . . . . . . . . . . . . . . . . . . . 24

TENSIONING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . 25

REPLACING THE SHARPENING STONE . . . . . . . . . . . . . . . . 26

CLEANING THE SAW . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

CHARGER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

WARRANTY AND SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

are registered trademarks of Blount, Inc. in the United States and/or in other countries.

3

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250 SYMBOLS AND LABELS

AF 0513  F/N 547361

SYMBOLS AND LABELS

SYMBOL

NAME EXPLANATION

CLASS II

CONSTRUCTION

DESIGNATED DOUBLE INSULATED CONSTRUCTION

TOOLS

SAFETY ALERT

SYMBOL

INDICATES THAT THE TEXT THAT FOLLOWS EXPLAINS A

DANGER, WARNING, OR CAUTION.

READ

INSTRUCTIONS

THE ORIGINAL INSTRUCTION MANUAL CONTAINS

IMPORTANT SAFETY AND OPERATING INFORMATION.

READ AND FOLLOW THE INSTRUCTIONS CAREFULLY.

WEAR EYE

PROTECTION

WEAR EYE PROTECTION WHEN OPERATING THE CHAIN

SAW.

WEAR HEARING

PROTECTION

WEAR HEARING PROTECTION WHEN OPERATING THE

CHAIN SAW.

WEAR HAND

PROTECTION

WEAR GLOVES WHEN OPERATING THE CHAIN SAW AND

WHEN HANDLING THE BAR AND CHAIN.

WEAR HEAD

PROTECTION WEAR A HARD HAT WHEN USING THE CHAIN SAW.

SOUND POWER SOUND POWER LEVEL IS 90 DB.

BEWARE OF

KICKBACK DANGER! KICKBACK CAN CAUSE SEVERE INJURIES.

BAR NOSE

CONTACT AVOID BAR NOSE CONTACT.

CHAIN KICKBACK

ANGLE USE LOW KICKBACK CHAIN.

TWOHANDED

HOLD HOLD SAW WITH TWO HANDS.

ONEHANDED

HOLD DO NOT HOLD SAW WITH ONE HAND.

DO NOT

INCINERATE DO NOT DISPOSE IN FLAMES.

DO NOT DISPOSE DO NOT THROW IN THE HOUSEHOLD WASTE. TAKE TO

AN AUTHORIZED RECYCLER.

DO NOT EXPOSE

TO RAIN DO NOT OPERATE THE CHARGER IN WET CONDITIONS.

INDOOR USE ONLY INTENDED FOR INDOOR USE ONLY.

OPERATING

TEMPERATURE

ONLY USE THE BATTERY PACK AT A TEMPERATURE

BETWEEN 32°F TO 104°F 0°C AND 40°C.

4

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

SAFETY RULES

AF 0513  F/N 547361

INTRODUCTION

This chain saw is designed for occasional light duty use. It is not designed to fell

large trees or cut large diameter logs. This chain saw is not designed for tree

service. Do not cut trees or wooden timbers that have a diameter equal to or

greater than the bar length.

SAFETY RULES

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: READ AND UNDERSTAND ALL SAFETY WARNINGS

AND ALL INSTRUCTIONS. FAILURE TO FOLLOW THE WARNINGS

AND INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR

SERIOUS INJURY.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE. THE

TERM “POWER TOOL” IN THE WARNINGS REFERS TO YOUR MAINSOPERATED

CORDED POWER TOOL OR BATTERY OPERATED CORDLESS POWER TOOL.

WORK AREA SAFETY

• Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

• Do not operate the chain saw in

explosive atmospheres, such as in the

presence of flammable liquids, gases

or dust. Power tools create sparks which may

ignite the dust or fumes.

• Keep children and bystanders away

while operating the chain saw.

Distractions can cause you to lose control.

• Identify and avoid gas lines,

electrical hazards, tripping hazards,

and potential sources of body

entanglement.

• Establish a safe zone for helpers. Helpers

should never stand directly in front of or

behind the operator. Helpers should always

stand to the side or perpendicular to the

direction of the cut.

ELECTRICAL SAFETY

• Charger plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) charger. Unmodified plugs

and matching outlets will reduce the risk of

electric shock.

• Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

• Accidental splashing of water against

the chain saw from any direction will

present no harmful shock or hazard to

the operator.

• Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the charger. Keep cord

away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords

increase the risk of electric shock.

• While operating the charger outdoors,

use an extension cord suitable for

outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

5

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250 SAFETY RULES

AF 0513  F/N 547361

• If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply

or ground fault circuit interrupter

(GFCI). Use of a RCD (GFCI) reduces the risk of

electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are

doing and use common sense when

operating the chain saw. Do not use

the chain saw while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating chain saw may result in serious

personal injury.

• Use personal protective equipment.

Always wear eye protection. Protective

equipment such as a dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

• Remove any adjusting key or wrench

before turning the chain saw on. A

wrench or key left attached to a rotating part

of the chain saw may result in personal injury.

• Do not overreach. Keep proper footing

and balance at all times (Fig. ). This

enables better control of the chain saw in

unexpected situations.

• Dress properly. Do not wear loose

clothing or jewelry. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can

be caught in moving parts.

• Use two hands when operating the

chain saw.

• The work piece, bar, and chain can be

hot after cutting. Wear gloves to avoid

burns.

• Use proper auxiliary equipment

and ensure that it is not damaged,

of adequate strength, and securely

placed. Use auxiliary equipment only for the

purpose for which it is intended.

• Prolonged use of power tools has been

reported to cause vascular, muscular,

or neurological disorders (such as

vibration white finger or Raynaud’s

syndrome). To reduce the risk of injury,

follow these instructions:

– Wear gloves and keep hands and body

warm.

– Maintain a firm grip on the hedge

trimmer, but do not use prolonged,

excessive pressure.

– Take frequent breaks.

The vibration in normal use can differ

from the stated values depending on the

material being cut, maintenance of the

cutting system, and other factors.

POWER TOOL USE AND CARE

• Do not force the chain saw. Use the

correct chain saw for your application.

The correct chain saw will do the job better

and safer at the rate for which it was designed.

• Do not use the chain saw if the switch

does not turn it on and off.

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

• Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or

battery pack, picking up or carrying

the tool. Carrying power tools with your

finger on the switch or energizing power tools

that have the switch on invites accidents.

FIG. 1

6

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

SAFETY RULES

AF 0513  F/N 547361

• Disconnect the battery pack from

the chain saw before making any

adjustments, changing accessories, or

storing the chain saw. Such preventative

safety measures reduce the risk of starting the

chain saw accidently.

• Store idle chain saws out of the reach

of children and do not allow persons

unfamiliar with the chain saw or these

instructions to operate the chain saw.

Chain saws are dangerous in the hands of

untrained users.

• Maintain the chain saw. Check for

misalignment or binding of moving

parts, breakage of parts and any other

condition that may affect the chain

saw’s operation. If damaged, have the

chain saw repaired before use.

Many accidents are caused by poorly

maintained power tools.

• Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

• Use the chain saw, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the chain saw for

operations different from those intended

could result in a hazardous situation.

BATTERY TOOL USE AND CARE

• Recharge only with the charger

specified by OREGON®. A charger that

is suitable for one type of battery pack may

create a risk of fire when used with another

battery pack.

• Use the chain saw only with specifically

designated battery packs.

Use of any other battery packs may create risk

of injury and fire.

• When battery pack is not in use, keep

it away from other metal objects, like

paper clips, coins, keys, nails, screws

or other small metal objects, that can

make a connection from one terminal

to another. Shorting the battery terminal

may cause burns or a fire.

• Under abusive conditions, liquid may

be ejected from the battery; avoid

contact. If contact accidentally occurs, flush

with water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

• Do not disassemble the chain saw,

charger, or battery pack or attempt to

repair these products. Doing so could

result in electrical shock.

SERVICE

Have your chain saw serviced by a

qualified repair person using only

identical replacement parts.

This will ensure that the safety of the

chain saw is maintained.

7

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250 SAFETY RULES

AF 0513  F/N 547361

CHAIN SAW

SAFETY WARNINGS

• Keep all parts of the body away from

the saw chain when the chain saw is

operating. Before you start the chain

saw, make sure the saw chain is not

contacting anything. A moment of

inattention while operating chain saws may

cause entanglement of your clothing or body

with the saw chain.

• Always hold the chain saw with your

right hand on the rear handle and your

left hand on the front handle (Fig. ).

Holding the chain saw with a reversed hand

configuration increases the risk of personal

injury and should never be done.

• Wear safety glasses and hearing

protection. Further protective

equipment for head, hands, legs and

feet is recommended. Adequate protective

clothing will reduce personal injury by flying

debris or accidental contact with the saw

chain.

• Do not operate a chain saw in a tree.

Operation of a chain saw while up in a tree

may result in personal injury.

• Always keep proper footing and

operate the chain saw only when

standing on a fixed, secure and level

surface. Slippery or unstable surfaces may

cause a loss of balance or control of the chain

saw.

• When cutting a limb that is under

tension, be alert for spring back. When

the tension in the wood fibers is released the

spring loaded limb may strike the operator

and/or throw the chain saw out of control.

• Use extreme caution when cutting

brush and saplings. The slender material

may catch the saw chain and be whipped

toward you or pull you off balance.

• Carry the chain saw by the front handle

with the chain saw switched off and

away from your body. When

transporting or storing the chain saw

always fit the guide bar cover (Fig. ).

Proper handling of the chain saw will reduce

the likelihood of accidental contact with the

moving saw chain.

FIG. 2

FIG. 3

8

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

SAFETY RULES

AF 0513  F/N 547361

• Follow instructions for lubricating,

chain tensioning and changing

accessories. Improperly tensioned or

lubricated chain may either break or increase

the chance of kickback.

• Keep handles dry, clean, and free of oil

and grease. Greasy, oily handles are slippery

causing loss of control.

• Cut wood only. Do not use the chain

saw for purposes not intended. For

example: do not use chain saw for

cutting plastic, masonry, or non-wood

building materials. Use of the chain saw

for operations different than intended could

result in a hazardous situation.

• It is recommended that the first

time user should have practical

instruction in the use of the chain saw

and the protective equipment from

an experienced operator. The initial

practice should be cutting logs on a

saw-horse or cradle.

• Other than the wear parts identified in

this manual, the chain saw has no user

serviceable parts.

KICKBACK  CAUSES AND

OPERATOR PREVENTION

Kickback may occur when the nose or

tip of the guide bar touches an object, or

when the wood closes in and pinches the

saw chain in the cut.

Tip contact in some cases may cause

a sudden reverse reaction, kicking the

guide bar up and back towards the

operator.

Pinching the saw chain along the top of

the guide bar may push the guide bar

rapidly back towards the operator.

Either of these reactions may cause you

to lose control of the saw which could

result in serious personal injury. Do not

rely exclusively upon the safety devices

built into your saw. As a chain saw user,

you should take several steps to keep

your cutting jobs free from accident or

injury.

Kickback is the result of tool misuse and/

or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below:

• Maintain a firm grip, with thumbs

and fingers encircling the chain saw

handles, with both hands on the saw

and position your body and arm to

allow you to resist kickback forces.

Kickback forces can be controlled by the

operator. Do not let go of the chain saw.

• Do not overreach and do not cut

above shoulder height. This helps prevent

unintended tip contact and enables better

control of the chain saw in unexpected

situations.

• Only use replacement bars and

chains specified by OREGON®.

Incorrect replacement bars and chains may

cause chain breakage and/or kickback.

• Follow the OREGON® sharpening and

maintenance instructions for the saw

chain. Decreasing the depth gauge height

can lead to increased kickback.

KICKBACK SAFETY DEVICES

ON THIS SAW

CHAIN BRAKE

The chain saw comes equipped with a

chain brake, which stops both the motor

and the motion of the chain when

kickback occurs (Fig. ). The chain brake

can be activated by the forward motion

of the hand guard as the saw rotates

backward during kickback; it can also be

activated by the inertial forces generated

during rapid pushback.

FIG. 4

9

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250 SAFETY RULES

AF 0513  F/N 547361

DANGER: NEVER MODIFY OR

ATTEMPT TO DISABLE THE CHAIN

BRAKE.

CHAIN

This saw comes equipped with a saw

chain that met the reduced kickback

requirements of ANSI B. when tested

on a representative sample of chain saws.

For replacement chain, see “Specifications

and Components” in this manual.

BAR

This saw comes equipped with a guide

bar that has a small radius nose. Small

radius noses generally have less potential

for kickback.

When replacing the bar, be sure to order

the bar listed in this manual.

STORAGE, TRANSPORTING,

AND DISPOSAL

STORING THE SAW

• Remove the battery pack and

thoroughly clean the saw. See

“Maintenance and Cleaning” in this

manual. Install the blade cover prior to

storing.

• Store in a dry place out of reach of

children or pets.

• It is normal for a small amount of oil to

seep from the bar when the chain saw is

not in use. To protect against seepage,

install the blade cover and place an

absorbent pad under the guide bar.

STORING THE BATTERY PACK

When storing the battery pack longer

than nine months, follow these

guidelines:

• Remove the battery pack from the chain

saw or charger.

• Store in a cool, dry place.

• Keep out of reach of children or pets.

• To prolong battery life, never store

battery pack in a completely discharged

condition. (Fig. ).

• Store at a temperature between -°F to

°F (-°C and °C).

STORING THE CHARGER

• Remove battery pack from the charger.

• Disconnect charger from power source.

• Store in a dry place.

• Keep out of reach of children or pets.

See “Maintenance and Cleaning” for more

information.

FIG. 5

INDICATOR LIGHTS

10

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

SAFETY RULES

AF 0513  F/N 547361

TRANSPORTING THE CHAIN SAW

Remove the battery pack from the saw

and install the blade cover. Clean the saw

thoroughly and if desired, drain the bar

and chain oil to reduce seepage.

TRANSPORTING THE BATTERY PACK

Observe national regulations when

shipping lithium ion batteries. Special

package labeling may be required.

BATTERY PACK DISPOSAL

Do not dispose of battery pack in

household garbage or incinerate. Local

waste management and recycling

agencies have information on proper

recycling or disposal instructions. Battery

packs can be collected in the United

States or Canada through Rechargeable

Battery Recycling Corporation. OREGON®

has already paid the costs involved to

recycle battery packs. Return end of life

battery packs to participating retailer or

recycling center. Return locations and

more information can be found at

www.callrecycle.org or --BATTERY.

BATTERY SAFETY

DANGER: FAILURE TO FOLLOW

THESE SAFETY RULES CAN

CAUSE THE BATTERY PACK TO

LEAK HAZARDOUS CHEMICALS,

OVERHEAT, EMIT SMOKE, BURST,

FLARE, EXPLODE, AND/OR IGNITE.

CAUTION: DO NOT DISPOSE

OF THE BATTERY PACK IN THE

HOUSEHOLD WASTE OR FIRE.

LITHIUM ION BATTERY PACKS

SHOULD BE RECYCLED BY LOCAL

AUTHORIZED RECYCLER.

CAUTION: DO NOT EXPOSE

BATTERY PACK TO EXCESSIVE

HEAT, SUCH AS THE INTERIOR OF A

VEHICLE IN HOT WEATHER. SUCH

EXPOSURE CAN CAUSE A LOSS IN

PERFORMANCE AND/OR SERVICE

LIFE. DO NOT ATTEMPT TO RE

CHARGE A NONRECHARGEABLE

BATTERY PACK.

• Do not disassemble or modify the

battery pack. The battery pack is

equipped with built-in safety and

protection features which may be

inadvertently disabled.

• Do not connect the positive (+) and

negative (-) terminals with metal objects.

Do not transport or store the battery

pack together with metal objects such

as coins or screws. Short-circuiting may

occur or the metal object in contact

with the battery pack can generate heat.

• Do not discard the battery pack into

fire or otherwise expose to excessive

heat. Such conditions can cause the

insulation to melt or safety features to

be damaged.

• Do not use, charge, or store the battery

pack near a heat source as fire or a

heater that generate temperatures

above °F (°C). Overheating and/or

internal short circuiting may occur.

11

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250 SAFETY RULES

AF 0513  F/N 547361

• Do not immerse the battery pack in

water or expose it to extremely wet

conditions. Moisture can cause the

protective features to be damaged,

resulting in charging with extremely

high current and voltage, which may

lead to abnormal chemical reactions.

• To recharge the battery pack, use the

battery charger specifically designed

for the battery pack and observe the

specified charger safety precautions

detailed in this manual. Failure to do so

may result in extremely high current and

voltage, which may lead to abnormal

chemical reactions.

• Do not use OREGON® branded battery

packs in non-OREGON® branded tools.

• Do not strike, pierce, or throw battery

pack.

• Do not use an apparently damaged or

deformed battery pack.

• If the recharging operation fails to

complete even after the specified

recharging time has elapsed,

immediately stop further recharging.

• If the battery pack gives off an odor,

generates heat, becomes discolored

or deformed, or in any way appears

abnormal during use, recharging, or

storage, immediately remove it from the

equipment or charger.

• Any liquid leaking from the battery is

corrosive, can damage eyes and skin,

and may be toxic if swallowed.

CHARGER SAFETY

IMPORTANT SAFETY INSTRUCTIONS

 SAVE THESE INSTRUCTIONS

CAUTION: THIS APPLIANCE IS NOT

INTENDED FOR USE BY PERSONS

INCLUDING CHILDREN WITH

REDUCED PHYSICAL, SENSORY OR

MENTAL CAPABILITIES, OR LACK

OF KNOWLEDGE, UNLESS THEY

HAVE BEEN GIVEN SUPERVISION

OR INSTRUCTION BY A PERSON

RESPONSIBLE FOR THEIR SAFETY.

CHILDREN SHOULD BE SUPERVISED

TO ENSURE THAT THEY DO NOT PLAY

WITH THE APPLIANCES.

CAUTION: RISK OF INJURY FROM

ELECTRIC SHOCK AND FIRE. CHARGE

ONLY WITH LITHIUM ION BATTERIES

INTENDED FOR THIS APPLIANCE.

THIS CHARGER IS INTENDED FOR

DRY LOCATION USE ONLY. BEFORE

USING THE CHARGER, READ AND

UNDERSTAND ALL INSTRUCTIONS

AND SAFETY MARKINGS IN THIS

MANUAL, ON THE CHARGER AND ON

THE BATTERY PACKS.

CAUTION: USE THIS CHARGER

ONLY WITH THE SUPPLIED POWER

CORD, MAKING SURE THAT THE

INPUT PLUG CORRECTLY MATES TO

THE OUTPUT RECEPTACLE.

• Do not expose the charger to rain.

• Disconnect the charger from the power

supply when not in use.

• Do not disassemble the charger. THERE

ARE NO USER SERVICEABLE PARTS

INSIDE. Take it to an approved service

location when repair is required.

• Do not use the charger if it has been

dropped, received a sharp impact, or

otherwise damaged in any way. Replace

or take the charger to an approved

service location immediately.

• To reduce the risk of injury, charge only

the lithium ion batteries specified for

the charger.

• Do not operate the charger with

a damaged cord or plug. Replace

damaged power cord with the power

cord part number located in the

instructions. See “Specifications and

Components” in this manual.

• Locate the cord so that it will not be

tripped over, stepped on, or otherwise

subjected to potential damage.

• Never unplug the charger by pulling on

the cord; always pull by the plug.

12

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

PRODUCT IDENTIFICATION

AF 0513  F/N 547361

PRODUCT IDENTIFICATION

KNOW THE CHAIN SAW

SIDE COVER

HAND GUARD / CHAIN BRAKE

SIDE COVER KNOB

POWERSHARP® LEVER

CHAIN

BLADE COVER

GUIDE BAR

BATTERY

PACK

SPROCKET

SHARPENING STONE

BARMOUNTING STUD

BATTERY PORT

BATTERY

RELEASE

CHAIN TENSIONER SCREW

SIDE COVER CHAIN CATCH

REAR HANDLE

TRIGGER SWITCH

TRIGGER LOCKOUT

FRONT HANDLE

OIL RESERVOIR CAP

OIL INSPECTION

WINDOW

13

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250 SPECIFICATIONS AND COMPONENTS

AF 0513  F/N 547361

SPECIFICATIONS AND COMPONENTS

REPLACEMENT COMPONENTS PART NUMBER

GUIDE BAR 14 inch (35 cm) 91 SDE,

.050 inch (1.3 mm) 554874

SAW CHAIN AND STONE,

POWERSHARP®

14 inch (35 cm) 91,

LOW-KICKBACK 554873

ALTERNATIVE SAW CHAIN

14 inch (35 cm) 3/8 inch LOW

PROFILE 91 LOW-KICKBACK RATED

CHAIN

OREGON® S52

BATTERY PACK, MODEL B600E 548208

BATTERY PACK, MODEL B400E 545938

BATTERY PACK, MODEL B500S 545937

CHARGER WITH CORD, MODEL C600 540580

CHARGER WITH CORD, MODEL C750 548185

CHARGER, MODEL C600

INPUT 100240V~ 5060Hz 60W

INPUT U.S. AND CANADA ONLY 120V~ 60Hz 60W

OUTPUT 41.5V 1.25A

POWER CORD US/CAN P/N: 546636 EU P/N: 547383

UK P/N: 547384 AU/NZ P/N: 560663

BATTERY PACK

TYPE LITHIUM ION

OPERATING TEMPERATURES 32°F TO 104°F 0°C TO 40°C

MODEL CAPACITY,

NOMINAL

VOLTAGE,

NOMINAL

C600 CHARGE

TIME APPROX.

B600E 4.00 Ah / 144 Wh +36 VDC 210 MINUTES

B400E 2.40 Ah / 89 Wh +37 VDC 120 MINUTES

B500S 1.25 Ah / 47 Wh +37 VDC 60 MINUTES

CHAIN SAW

OIL CAPACITY 5.9 oz 175 ml)

BAR AND CHAIN OIL OREGON® BRAND

DRY WEIGHT WITH B400E 12.0 lb 5.4 kg

DRY WEIGHT WITHOUT

BATTERY, BAR, AND CHAIN 7.9 lb 3.6 kg

SOUND POWER LEVEL 90dB

VIBRATION 2.87 m/s2 (K, 1.5 m/s2)

MAX BAR LENGTH 14 inch (35 cm)

CHAIN PITCH 3/8 inch LOW PROFILE - 91

CHAIN GAUGE .050 inch (1.3 mm)

SPROCKET TEETH 6

NO LOAD CHAIN SPEED 12 m/s

14

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

CHAIN SAW NAMES AND TERMS

AF 0513  F/N 547361

CHAIN SAW NAMES AND TERMS

Alignment flange: The long, raised portion

of the bar pad holding the mounting

stud.

Automatic oiler: A system that

automatically lubricates the guide bar

and saw chain.

Bucking: The process of cross-cutting a

felled tree or log into lengths.

Chain brake: A device used to stop the

saw chain.

Chain saw powerhead: A chain saw

without the saw chain or guide bar.

Drive sprocket: The toothed part that

drives the saw chain.

Felling: The process of cutting down a

tree.

Felling back cut: The final cut in a tree

felling operation made on the opposite

side of the tree from the notching

undercut.

Front handle: The support handle located

at or toward the front of the chain saw.

Hand guard: A structural barrier between

the front handle of a chain saw and

the guide bar, which also serves as an

activating mechanism for the chain

brake.

Guide bar: A railed structure that supports

and guides the saw chain.

Kickback: The backward or upward

motion, or both, of the guide bar

occurring when the saw chain near the

nose of the top area of the guide bar

contacts any object such as a log or

branch, or when the wood closes in and

pinches the saw chain in the cut.

Low-kickback chain: A chain that

complies with the kickback performance

requirements of ANSI B..

Normal cutting position: Those positions

assumed in performing the bucking and

felling cuts.

Notching undercut: A notch cut in a tree

that directs the tree’s fall.

Rear handle: The support handle located

at or toward the rear of the saw.

Reduced kickback guide bar: A guide bar

which has been demonstrated to reduce

kickback significantly.

Saw chain: A loop of chain having

cutting teeth, that cuts the wood, and

that is driven by the powerhead and is

supported by the guide bar.

Trigger lock-out: A movable stop that

prevents the unintentional operation

of the trigger switch until manually

actuated.

Trigger switch: A device that turns the

chain saw on and off.

15

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250 ASSEMBLY

AF 0513  F/N 547361

ASSEMBLY

UNPACKING

DANGER: DO NOT ATTEMPT TO

OPERATE THE CHAIN SAW IF ANY

PART IS DAMAGED OR MISSING.

Some chain saw kits come completely

assembled. If the chain saw has been

packaged without the saw chain and

guide bar installed, see “Replacing the Bar

and Chain” in this manual for installation

instructions. After removing the chain

saw from its box, inspect it carefully to

make sure no damage has occurred

during shipping.

Inspect the chain saw for missing parts.

If any parts are damaged or missing,

contact OREGON® to obtain replacement

parts at ...

IMPORTANT: AFTER UNPACKING THE

CHAIN SAW, CHECK THE POSITION OF

THE HAND GUARD. THE CHAIN SAW

WILL NOT RUN WITH THE CHAIN BRAKE

ENGAGED. PULL THE HAND GUARD

BACK TOWARDS THE FRONT HANDLE

BEFORE OPERATION (FIG. ).

INSTALLING BUCKING SPIKES

Some chain saw kits come with metal

bucking spikes as an accessory. To install

the spikes, position on the front of the

saw with the spikes facing upward, then

fasten with the two supplied screws.

FILLING OIL RESERVOIR

CAUTION: CHECK OIL LEVEL

FREQUENTLY AND FILL AS NEEDED.

NEVER OPERATE THE CHAIN SAW IF

OIL IS NOT VISIBLE.

Bar and chain oil is required to properly

lubricate the bar and chain. Use

OREGON® bar and chain oil for best

results. It is specially designed to provide

low friction and faster cuts. NEVER use

oil or other lubricants not specifically

designed for use on the bar and chain.

This can lead to a clogged oil system,

which may cause premature wear of the

bar and chain.

Place the chain saw on its side on a firm,

flat surface, so that the oil cap is on top

(Fig. ). After cleaning any debris from the

cap area, remove the cap and carefully

pour the bar and chain oil into the

reservoir. Replace the cap and check the

presence of oil through the oil inspection

window. Additional bar and chain oil is

necessary shortly after oil is no longer

viewable through the oil inspection

window.

FIG. 6

HAND GUARD IN

OPERATING POSITION

HAND GUARD IN

BRAKE POSITION

FIG. 7

16

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

OPERATING THE SAW

AF 0513  F/N 547361

OPERATING THE SAW

BATTERY PACK AND CHARGER

WARNING: DO NOT CHARGE THE

BATTERY PACK IN THE RAIN.

BATTERY PACK LED CHARGELEVEL

INDICATOR

The lithium ion battery pack is equipped

with an LED charge-level indicator. To test

the charge level of the battery pack, press

the indicator button on the battery pack’s

face (Fig. ).

No lights: recharge.

One steady green light:

less than % charged.

Charge battery pack before use.

Two steady green lights:

–% charged.

Three steady green lights:

–% charged.

Four steady green lights:

–% charged.

CONNECTING THE CHARGER

Connect the charger cord to the charger

and to the proper electrical outlet (Fig. ).

Only use the cord set that was supplied

with the charger. At first use, verify that

the plug type matches the receptacle.

CHARGER LED CHARGESTATE

INDICATOR

The battery charger is equipped with an

LED charge-state indicator that indicates

the state of charging as well as conditions

that may delay or prevent charging

(Fig. ).

Note: Until a battery pack is inserted, no

lights will be visible.

Blinking orange light: a fault

condition exists. There are

several potential causes. See

“Troubleshooting” in this manual.

Steady orange light: the battery

pack temperature is beyond the

acceptable range (°F/°C to

°F/°C). Allow the battery pack

to reach the acceptable

temperature range before

charging. The pack may be left on

the charger as the temperature

adjusts. Charging will begin when

the proper temperature is

reached.

Blinking green light: battery pack

is charging.

Steady green light: battery pack is

ready for use.

FIG. 8

INDICATOR LIGHTS

INDICATOR BUTTON

FIG. 9

FIG. 10

17

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250 OPERATING THE SAW

AF 0513  F/N 547361

CHARGING THE BATTERY PACK

WARNING: FAILURE TO FOLLOW

PROPER CHARGING PROCEDURES

MAY CAUSE EXCESSIVE VOLTAGE,

EXCESSIVE CURRENT FLOW, LOSS

OF CONTROL DURING CHARGING,

LEAKAGE OF HAZARDOUS

CHEMICALS, HEAT GENERATION,

BURSTING, OR FIRE.

With the charger cord connected to the

charger and plugged into an electrical

outlet, align the grooves in the battery

with the rails on the charger and slide the

battery pack onto the charger until fully

seated (Fig. ).

Check the charge-state indicator for

charging conditions.

INSERTING AND RELEASING

THE BATTERY PACK

Only use the OREGON® brand battery

packs specified in these operating

instructions.

Align the groove in the battery with the

rails inside the battery port. Firmly insert

the battery pack into the chain saw’s

battery port, pressing forward until it

clicks as it locks into place (Fig. ).

To remove the battery pack, lift up on

the battery release and remove the pack

(Fig. ).

FIG. 11

FIG. 12

FIG. 13

18

OREGON® CORDLESS TOOL SYSTEM

CHAIN SAW MODEL CS250

OPERATING THE SAW

AF 0513  F/N 547361

GENERAL OPERATION

WARNING: ALWAYS WEAR PROPER

GLOVES, HEAD, EAR, AND EYE

PROTECTION.

OPERATING TEMPERATURE

This chain saw is designed to operate

within a temperature range of °F to

°F (°C to °C).

GRIP

With the saw on a firm, flat surface, grasp

the front handle with the left hand and

the rear handle with the right. Fingers

should wrap over the top of the handle

and the thumb below the handle (Fig. ).

STANCE

Both feet should be on solid ground, with

weight evenly spread between them.

Do not overreach and do not stand on a

ladder, stepstool, or any raised position

that is not fully secured.

STOPPING THE SAW

Release the trigger switch to stop the

chain saw.

TESTING THE BRAKE

Make sure the chain brake is working

before using the chain saw. To check

brake operation, start the saw on a firm

flat surface, and then move the hand

guard forward to manually activate the

chain brake. A properly functioning

chain brake stops the motor and saw

chain immediately.

STARTING THE SAW

Grasp the top and rear handles firmly.

Press and hold the trigger lock-out with

the thumb (). To start the saw, squeeze

the trigger switch () (Fig. ). There is no

need to continue to press the trigger

lock-out.

GRIP WITH THUMB

BELOW HANDLE

FIG. 14

1 TRIGGER LOCKOUT

2 TRIGGER

SWITCH

FIG. 15

La page charge ...

Oregon Scientific CS250 Original Instruction Manual

Oregon Scientific CS250 Original Instruction Manual

dans d''autres langues

Documents connexes

Autres documents