Oregon Scientific CS250 Original Instruction Manual

Catégorie
Tronçonneuses électriques
Taper
Original Instruction Manual
AF 0513 - F/N 547361
ORIGINAL INSTRUCTION MANUAL
CHAIN SAW MODEL CS250
MANUEL D’INSTRUCTION ORIGINAL
TRONÇONNEUSE MODÈLECS250
MANUAL DE INSTRUCCIONES ORIGINAL
MOTOSIERRA MODELO CS250
1
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
AF 0513  F/N 547361
ENGLISH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
WARNING: READ AND UNDERSTAND ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. FAILURE TO FOLLOW
THE WARNINGS AND INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR SERIOUS INJURY.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
AVERTISSEMENT: VEUILLEZ LIRE ET COMPRENDRE TOUS LES AVERTISSEMENTS DE SÉCURITÉ ET TOUTES
LES INSTRUCTIONS. LE NON-RESPECT DES AVERTISSEMENTS DE SÉCURITÉ ET DES INSTRUCTIONS PEUT ENTRAÎNER
UNE DÉCHARGE ÉLECTRIQUE, UN INCENDIE ET/OU DES BLESSURES GRAVES.
CONSERVEZ L’ENSEMBLE DES AVERTISSEMENTS ET INSTRUCTIONS POUR RÉFÉRENCE ULTÉRIEURE.
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
ADVERTENCIA: LEA Y COMPRENDA TODAS LAS ADVERTENCIAS DE SEGURIDAD Y TODAS LAS INSTRUCCIONES.
NO SEGUIR LAS ADVERTENCIAS Y LAS INSTRUCCIONES PUEDE PROVOCAR CHOQUES ELÉCTRICOS, INCENDIOS Y/O
LESIONES GRAVES.
CONSERVE TODAS LAS ADVERTENCIAS E INSTRUCCIONES COMO REFERENCIA PARA EL FUTURO.
2
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
TABLE OF CONTENTS
AF 0513  F/N 547361
TABLE OF CONTENTS
SYMBOLS AND LABELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
GENERAL POWER TOOL SAFETY WARNINGS. . . . . . . . . . . . .4
WORK AREA SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ELECTRICAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PERSONAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CHAIN SAW SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . 7
STORAGE, TRANSPORTING, AND DISPOSAL . . . . . . . . . . . . . 9
BATTERY SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CHARGER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PRODUCT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SPECIFICATIONS AND COMPONENTS . . . . . . . . . . . . . . . . . . . . 13
CHAIN SAW NAMES AND TERMS. . . . . . . . . . . . . . . . . . . . . . . . 14
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
FILLING OIL RESERVOIR . . . . . . . . . . . . . . . . . . . . . . . . . . 15
OPERATING THE SAW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
BATTERY PACK AND CHARGER . . . . . . . . . . . . . . . . . . . . . 16
GENERAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CUTTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SHARPENING WITH POWERSHARP®. . . . . . . . . . . . . . . . . . . . . . 22
MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . 23
REPLACING THE BAR AND CHAIN . . . . . . . . . . . . . . . . . . . 24
TENSIONING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . 25
REPLACING THE SHARPENING STONE . . . . . . . . . . . . . . . . 26
CLEANING THE SAW . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CHARGER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
WARRANTY AND SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
©  Blount, Inc. Pricing and specifications subject to change without notice. All rights reserved. OREGON® and PowerSharp®
are registered trademarks of Blount, Inc. in the United States and/or in other countries.
3
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250 SYMBOLS AND LABELS
AF 0513  F/N 547361
SYMBOLS AND LABELS
SYMBOL
NAME EXPLANATION
CLASS II
CONSTRUCTION
DESIGNATED DOUBLE INSULATED CONSTRUCTION
TOOLS
SAFETY ALERT
SYMBOL
INDICATES THAT THE TEXT THAT FOLLOWS EXPLAINS A
DANGER, WARNING, OR CAUTION.
READ
INSTRUCTIONS
THE ORIGINAL INSTRUCTION MANUAL CONTAINS
IMPORTANT SAFETY AND OPERATING INFORMATION.
READ AND FOLLOW THE INSTRUCTIONS CAREFULLY.
WEAR EYE
PROTECTION
WEAR EYE PROTECTION WHEN OPERATING THE CHAIN
SAW.
WEAR HEARING
PROTECTION
WEAR HEARING PROTECTION WHEN OPERATING THE
CHAIN SAW.
WEAR HAND
PROTECTION
WEAR GLOVES WHEN OPERATING THE CHAIN SAW AND
WHEN HANDLING THE BAR AND CHAIN.
WEAR HEAD
PROTECTION WEAR A HARD HAT WHEN USING THE CHAIN SAW.
SOUND POWER SOUND POWER LEVEL IS 90 DB.
BEWARE OF
KICKBACK DANGER! KICKBACK CAN CAUSE SEVERE INJURIES.
BAR NOSE
CONTACT AVOID BAR NOSE CONTACT.
CHAIN KICKBACK
ANGLE USE LOW KICKBACK CHAIN.
TWOHANDED
HOLD HOLD SAW WITH TWO HANDS.
ONEHANDED
HOLD DO NOT HOLD SAW WITH ONE HAND.
DO NOT
INCINERATE DO NOT DISPOSE IN FLAMES.
DO NOT DISPOSE DO NOT THROW IN THE HOUSEHOLD WASTE. TAKE TO
AN AUTHORIZED RECYCLER.
DO NOT EXPOSE
TO RAIN DO NOT OPERATE THE CHARGER IN WET CONDITIONS.
INDOOR USE ONLY INTENDED FOR INDOOR USE ONLY.
OPERATING
TEMPERATURE
ONLY USE THE BATTERY PACK AT A TEMPERATURE
BETWEEN 32°F TO 104°F 0°C AND 40°C.
4
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
SAFETY RULES
AF 0513  F/N 547361
INTRODUCTION
This chain saw is designed for occasional light duty use. It is not designed to fell
large trees or cut large diameter logs. This chain saw is not designed for tree
service. Do not cut trees or wooden timbers that have a diameter equal to or
greater than the bar length.
SAFETY RULES
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: READ AND UNDERSTAND ALL SAFETY WARNINGS
AND ALL INSTRUCTIONS. FAILURE TO FOLLOW THE WARNINGS
AND INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR
SERIOUS INJURY.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE. THE
TERM “POWER TOOL” IN THE WARNINGS REFERS TO YOUR MAINSOPERATED
CORDED POWER TOOL OR BATTERY OPERATED CORDLESS POWER TOOL.
WORK AREA SAFETY
Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
Do not operate the chain saw in
explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust. Power tools create sparks which may
ignite the dust or fumes.
Keep children and bystanders away
while operating the chain saw.
Distractions can cause you to lose control.
Identify and avoid gas lines,
electrical hazards, tripping hazards,
and potential sources of body
entanglement.
Establish a safe zone for helpers. Helpers
should never stand directly in front of or
behind the operator. Helpers should always
stand to the side or perpendicular to the
direction of the cut.
ELECTRICAL SAFETY
Charger plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) charger. Unmodified plugs
and matching outlets will reduce the risk of
electric shock.
Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
Accidental splashing of water against
the chain saw from any direction will
present no harmful shock or hazard to
the operator.
Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the charger. Keep cord
away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
While operating the charger outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
5
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250 SAFETY RULES
AF 0513  F/N 547361
If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply
or ground fault circuit interrupter
(GFCI). Use of a RCD (GFCI) reduces the risk of
electric shock.
PERSONAL SAFETY
Stay alert, watch what you are
doing and use common sense when
operating the chain saw. Do not use
the chain saw while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating chain saw may result in serious
personal injury.
Use personal protective equipment.
Always wear eye protection. Protective
equipment such as a dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
Remove any adjusting key or wrench
before turning the chain saw on. A
wrench or key left attached to a rotating part
of the chain saw may result in personal injury.
Do not overreach. Keep proper footing
and balance at all times (Fig. ). This
enables better control of the chain saw in
unexpected situations.
Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
Use two hands when operating the
chain saw.
The work piece, bar, and chain can be
hot after cutting. Wear gloves to avoid
burns.
Use proper auxiliary equipment
and ensure that it is not damaged,
of adequate strength, and securely
placed. Use auxiliary equipment only for the
purpose for which it is intended.
Prolonged use of power tools has been
reported to cause vascular, muscular,
or neurological disorders (such as
vibration white finger or Raynaud’s
syndrome). To reduce the risk of injury,
follow these instructions:
Wear gloves and keep hands and body
warm.
Maintain a firm grip on the hedge
trimmer, but do not use prolonged,
excessive pressure.
Take frequent breaks.
The vibration in normal use can differ
from the stated values depending on the
material being cut, maintenance of the
cutting system, and other factors.
POWER TOOL USE AND CARE
Do not force the chain saw. Use the
correct chain saw for your application.
The correct chain saw will do the job better
and safer at the rate for which it was designed.
Do not use the chain saw if the switch
does not turn it on and off.
Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying
the tool. Carrying power tools with your
finger on the switch or energizing power tools
that have the switch on invites accidents.
FIG. 1
6
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
SAFETY RULES
AF 0513  F/N 547361
Disconnect the battery pack from
the chain saw before making any
adjustments, changing accessories, or
storing the chain saw. Such preventative
safety measures reduce the risk of starting the
chain saw accidently.
Store idle chain saws out of the reach
of children and do not allow persons
unfamiliar with the chain saw or these
instructions to operate the chain saw.
Chain saws are dangerous in the hands of
untrained users.
Maintain the chain saw. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the chain
saw’s operation. If damaged, have the
chain saw repaired before use.
Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
Use the chain saw, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the chain saw for
operations different from those intended
could result in a hazardous situation.
BATTERY TOOL USE AND CARE
Recharge only with the charger
specified by OREGON®. A charger that
is suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
Use the chain saw only with specifically
designated battery packs.
Use of any other battery packs may create risk
of injury and fire.
When battery pack is not in use, keep
it away from other metal objects, like
paper clips, coins, keys, nails, screws
or other small metal objects, that can
make a connection from one terminal
to another. Shorting the battery terminal
may cause burns or a fire.
Under abusive conditions, liquid may
be ejected from the battery; avoid
contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
Do not disassemble the chain saw,
charger, or battery pack or attempt to
repair these products. Doing so could
result in electrical shock.
SERVICE
Have your chain saw serviced by a
qualified repair person using only
identical replacement parts.
This will ensure that the safety of the
chain saw is maintained.
7
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250 SAFETY RULES
AF 0513  F/N 547361
CHAIN SAW
SAFETY WARNINGS
Keep all parts of the body away from
the saw chain when the chain saw is
operating. Before you start the chain
saw, make sure the saw chain is not
contacting anything. A moment of
inattention while operating chain saws may
cause entanglement of your clothing or body
with the saw chain.
Always hold the chain saw with your
right hand on the rear handle and your
left hand on the front handle (Fig. ).
Holding the chain saw with a reversed hand
configuration increases the risk of personal
injury and should never be done.
Wear safety glasses and hearing
protection. Further protective
equipment for head, hands, legs and
feet is recommended. Adequate protective
clothing will reduce personal injury by flying
debris or accidental contact with the saw
chain.
Do not operate a chain saw in a tree.
Operation of a chain saw while up in a tree
may result in personal injury.
Always keep proper footing and
operate the chain saw only when
standing on a fixed, secure and level
surface. Slippery or unstable surfaces may
cause a loss of balance or control of the chain
saw.
When cutting a limb that is under
tension, be alert for spring back. When
the tension in the wood fibers is released the
spring loaded limb may strike the operator
and/or throw the chain saw out of control.
Use extreme caution when cutting
brush and saplings. The slender material
may catch the saw chain and be whipped
toward you or pull you off balance.
Carry the chain saw by the front handle
with the chain saw switched off and
away from your body. When
transporting or storing the chain saw
always fit the guide bar cover (Fig. ).
Proper handling of the chain saw will reduce
the likelihood of accidental contact with the
moving saw chain.
FIG. 2
FIG. 3
8
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
SAFETY RULES
AF 0513  F/N 547361
Follow instructions for lubricating,
chain tensioning and changing
accessories. Improperly tensioned or
lubricated chain may either break or increase
the chance of kickback.
Keep handles dry, clean, and free of oil
and grease. Greasy, oily handles are slippery
causing loss of control.
Cut wood only. Do not use the chain
saw for purposes not intended. For
example: do not use chain saw for
cutting plastic, masonry, or non-wood
building materials. Use of the chain saw
for operations different than intended could
result in a hazardous situation.
It is recommended that the first
time user should have practical
instruction in the use of the chain saw
and the protective equipment from
an experienced operator. The initial
practice should be cutting logs on a
saw-horse or cradle.
Other than the wear parts identified in
this manual, the chain saw has no user
serviceable parts.
KICKBACK  CAUSES AND
OPERATOR PREVENTION
Kickback may occur when the nose or
tip of the guide bar touches an object, or
when the wood closes in and pinches the
saw chain in the cut.
Tip contact in some cases may cause
a sudden reverse reaction, kicking the
guide bar up and back towards the
operator.
Pinching the saw chain along the top of
the guide bar may push the guide bar
rapidly back towards the operator.
Either of these reactions may cause you
to lose control of the saw which could
result in serious personal injury. Do not
rely exclusively upon the safety devices
built into your saw. As a chain saw user,
you should take several steps to keep
your cutting jobs free from accident or
injury.
Kickback is the result of tool misuse and/
or incorrect operating procedures or
conditions and can be avoided by taking
proper precautions as given below:
Maintain a firm grip, with thumbs
and fingers encircling the chain saw
handles, with both hands on the saw
and position your body and arm to
allow you to resist kickback forces.
Kickback forces can be controlled by the
operator. Do not let go of the chain saw.
Do not overreach and do not cut
above shoulder height. This helps prevent
unintended tip contact and enables better
control of the chain saw in unexpected
situations.
Only use replacement bars and
chains specified by OREGON®.
Incorrect replacement bars and chains may
cause chain breakage and/or kickback.
Follow the OREGON® sharpening and
maintenance instructions for the saw
chain. Decreasing the depth gauge height
can lead to increased kickback.
KICKBACK SAFETY DEVICES
ON THIS SAW
CHAIN BRAKE
The chain saw comes equipped with a
chain brake, which stops both the motor
and the motion of the chain when
kickback occurs (Fig. ). The chain brake
can be activated by the forward motion
of the hand guard as the saw rotates
backward during kickback; it can also be
activated by the inertial forces generated
during rapid pushback.
FIG. 4
9
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250 SAFETY RULES
AF 0513  F/N 547361
DANGER: NEVER MODIFY OR
ATTEMPT TO DISABLE THE CHAIN
BRAKE.
CHAIN
This saw comes equipped with a saw
chain that met the reduced kickback
requirements of ANSI B. when tested
on a representative sample of chain saws.
For replacement chain, see “Specifications
and Components in this manual.
BAR
This saw comes equipped with a guide
bar that has a small radius nose. Small
radius noses generally have less potential
for kickback.
When replacing the bar, be sure to order
the bar listed in this manual.
STORAGE, TRANSPORTING,
AND DISPOSAL
STORING THE SAW
Remove the battery pack and
thoroughly clean the saw. See
“Maintenance and Cleaning in this
manual. Install the blade cover prior to
storing.
Store in a dry place out of reach of
children or pets.
It is normal for a small amount of oil to
seep from the bar when the chain saw is
not in use. To protect against seepage,
install the blade cover and place an
absorbent pad under the guide bar.
STORING THE BATTERY PACK
When storing the battery pack longer
than nine months, follow these
guidelines:
Remove the battery pack from the chain
saw or charger.
Store in a cool, dry place.
Keep out of reach of children or pets.
To prolong battery life, never store
battery pack in a completely discharged
condition. (Fig. ).
Store at a temperature between -°F to
°F (-°C and °C).
STORING THE CHARGER
Remove battery pack from the charger.
Disconnect charger from power source.
Store in a dry place.
Keep out of reach of children or pets.
See “Maintenance and Cleaning for more
information.
FIG. 5
INDICATOR LIGHTS
10
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
SAFETY RULES
AF 0513  F/N 547361
TRANSPORTING THE CHAIN SAW
Remove the battery pack from the saw
and install the blade cover. Clean the saw
thoroughly and if desired, drain the bar
and chain oil to reduce seepage.
TRANSPORTING THE BATTERY PACK
Observe national regulations when
shipping lithium ion batteries. Special
package labeling may be required.
BATTERY PACK DISPOSAL
Do not dispose of battery pack in
household garbage or incinerate. Local
waste management and recycling
agencies have information on proper
recycling or disposal instructions. Battery
packs can be collected in the United
States or Canada through Rechargeable
Battery Recycling Corporation. OREGON®
has already paid the costs involved to
recycle battery packs. Return end of life
battery packs to participating retailer or
recycling center. Return locations and
more information can be found at
www.callrecycle.org or --BATTERY.
BATTERY SAFETY
DANGER: FAILURE TO FOLLOW
THESE SAFETY RULES CAN
CAUSE THE BATTERY PACK TO
LEAK HAZARDOUS CHEMICALS,
OVERHEAT, EMIT SMOKE, BURST,
FLARE, EXPLODE, AND/OR IGNITE.
CAUTION: DO NOT DISPOSE
OF THE BATTERY PACK IN THE
HOUSEHOLD WASTE OR FIRE.
LITHIUM ION BATTERY PACKS
SHOULD BE RECYCLED BY LOCAL
AUTHORIZED RECYCLER.
CAUTION: DO NOT EXPOSE
BATTERY PACK TO EXCESSIVE
HEAT, SUCH AS THE INTERIOR OF A
VEHICLE IN HOT WEATHER. SUCH
EXPOSURE CAN CAUSE A LOSS IN
PERFORMANCE AND/OR SERVICE
LIFE. DO NOT ATTEMPT TO RE
CHARGE A NONRECHARGEABLE
BATTERY PACK.
Do not disassemble or modify the
battery pack. The battery pack is
equipped with built-in safety and
protection features which may be
inadvertently disabled.
Do not connect the positive (+) and
negative (-) terminals with metal objects.
Do not transport or store the battery
pack together with metal objects such
as coins or screws. Short-circuiting may
occur or the metal object in contact
with the battery pack can generate heat.
Do not discard the battery pack into
fire or otherwise expose to excessive
heat. Such conditions can cause the
insulation to melt or safety features to
be damaged.
Do not use, charge, or store the battery
pack near a heat source as fire or a
heater that generate temperatures
above °F (°C). Overheating and/or
internal short circuiting may occur.
11
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250 SAFETY RULES
AF 0513  F/N 547361
Do not immerse the battery pack in
water or expose it to extremely wet
conditions. Moisture can cause the
protective features to be damaged,
resulting in charging with extremely
high current and voltage, which may
lead to abnormal chemical reactions.
To recharge the battery pack, use the
battery charger specifically designed
for the battery pack and observe the
specified charger safety precautions
detailed in this manual. Failure to do so
may result in extremely high current and
voltage, which may lead to abnormal
chemical reactions.
Do not use OREGON® branded battery
packs in non-OREGON® branded tools.
Do not strike, pierce, or throw battery
pack.
Do not use an apparently damaged or
deformed battery pack.
If the recharging operation fails to
complete even after the specified
recharging time has elapsed,
immediately stop further recharging.
If the battery pack gives off an odor,
generates heat, becomes discolored
or deformed, or in any way appears
abnormal during use, recharging, or
storage, immediately remove it from the
equipment or charger.
Any liquid leaking from the battery is
corrosive, can damage eyes and skin,
and may be toxic if swallowed.
CHARGER SAFETY
IMPORTANT SAFETY INSTRUCTIONS
 SAVE THESE INSTRUCTIONS
CAUTION: THIS APPLIANCE IS NOT
INTENDED FOR USE BY PERSONS
INCLUDING CHILDREN WITH
REDUCED PHYSICAL, SENSORY OR
MENTAL CAPABILITIES, OR LACK
OF KNOWLEDGE, UNLESS THEY
HAVE BEEN GIVEN SUPERVISION
OR INSTRUCTION BY A PERSON
RESPONSIBLE FOR THEIR SAFETY.
CHILDREN SHOULD BE SUPERVISED
TO ENSURE THAT THEY DO NOT PLAY
WITH THE APPLIANCES.
CAUTION: RISK OF INJURY FROM
ELECTRIC SHOCK AND FIRE. CHARGE
ONLY WITH LITHIUM ION BATTERIES
INTENDED FOR THIS APPLIANCE.
THIS CHARGER IS INTENDED FOR
DRY LOCATION USE ONLY. BEFORE
USING THE CHARGER, READ AND
UNDERSTAND ALL INSTRUCTIONS
AND SAFETY MARKINGS IN THIS
MANUAL, ON THE CHARGER AND ON
THE BATTERY PACKS.
CAUTION: USE THIS CHARGER
ONLY WITH THE SUPPLIED POWER
CORD, MAKING SURE THAT THE
INPUT PLUG CORRECTLY MATES TO
THE OUTPUT RECEPTACLE.
Do not expose the charger to rain.
Disconnect the charger from the power
supply when not in use.
Do not disassemble the charger. THERE
ARE NO USER SERVICEABLE PARTS
INSIDE. Take it to an approved service
location when repair is required.
Do not use the charger if it has been
dropped, received a sharp impact, or
otherwise damaged in any way. Replace
or take the charger to an approved
service location immediately.
To reduce the risk of injury, charge only
the lithium ion batteries specified for
the charger.
Do not operate the charger with
a damaged cord or plug. Replace
damaged power cord with the power
cord part number located in the
instructions. See “Specifications and
Components in this manual.
Locate the cord so that it will not be
tripped over, stepped on, or otherwise
subjected to potential damage.
Never unplug the charger by pulling on
the cord; always pull by the plug.
12
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
PRODUCT IDENTIFICATION
AF 0513  F/N 547361
PRODUCT IDENTIFICATION
KNOW THE CHAIN SAW
SIDE COVER
HAND GUARD / CHAIN BRAKE
SIDE COVER KNOB
POWERSHARP® LEVER
CHAIN
BLADE COVER
GUIDE BAR
BATTERY
PACK
SPROCKET
SHARPENING STONE
BARMOUNTING STUD
BATTERY PORT
BATTERY
RELEASE
CHAIN TENSIONER SCREW
SIDE COVER CHAIN CATCH
REAR HANDLE
TRIGGER SWITCH
TRIGGER LOCKOUT
FRONT HANDLE
OIL RESERVOIR CAP
OIL INSPECTION
WINDOW
13
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250 SPECIFICATIONS AND COMPONENTS
AF 0513  F/N 547361
SPECIFICATIONS AND COMPONENTS
REPLACEMENT COMPONENTS PART NUMBER
GUIDE BAR 14 inch (35 cm) 91 SDE,
.050 inch (1.3 mm) 554874
SAW CHAIN AND STONE,
POWERSHARP®
14 inch (35 cm) 91,
LOW-KICKBACK 554873
ALTERNATIVE SAW CHAIN
14 inch (35 cm) 3/8 inch LOW
PROFILE 91 LOW-KICKBACK RATED
CHAIN
OREGON® S52
BATTERY PACK, MODEL B600E 548208
BATTERY PACK, MODEL B400E 545938
BATTERY PACK, MODEL B500S 545937
CHARGER WITH CORD, MODEL C600 540580
CHARGER WITH CORD, MODEL C750 548185
CHARGER, MODEL C600
INPUT 100240V~ 5060Hz 60W
INPUT U.S. AND CANADA ONLY 120V~ 60Hz 60W
OUTPUT 41.5V 1.25A
POWER CORD US/CAN P/N: 546636 EU P/N: 547383
UK P/N: 547384 AU/NZ P/N: 560663
BATTERY PACK
TYPE LITHIUM ION
OPERATING TEMPERATURES 32°F TO 104°F 0°C TO 40°C
MODEL CAPACITY,
NOMINAL
VOLTAGE,
NOMINAL
C600 CHARGE
TIME APPROX.
B600E 4.00 Ah / 144 Wh +36 VDC 210 MINUTES
B400E 2.40 Ah / 89 Wh +37 VDC 120 MINUTES
B500S 1.25 Ah / 47 Wh +37 VDC 60 MINUTES
CHAIN SAW
OIL CAPACITY 5.9 oz 175 ml)
BAR AND CHAIN OIL OREGON® BRAND
DRY WEIGHT WITH B400E 12.0 lb 5.4 kg
DRY WEIGHT WITHOUT
BATTERY, BAR, AND CHAIN 7.9 lb 3.6 kg
SOUND POWER LEVEL 90dB
VIBRATION 2.87 m/s2 (K, 1.5 m/s2)
MAX BAR LENGTH 14 inch (35 cm)
CHAIN PITCH 3/8 inch LOW PROFILE - 91
CHAIN GAUGE .050 inch (1.3 mm)
SPROCKET TEETH 6
NO LOAD CHAIN SPEED 12 m/s
14
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
CHAIN SAW NAMES AND TERMS
AF 0513  F/N 547361
CHAIN SAW NAMES AND TERMS
Alignment flange: The long, raised portion
of the bar pad holding the mounting
stud.
Automatic oiler: A system that
automatically lubricates the guide bar
and saw chain.
Bucking: The process of cross-cutting a
felled tree or log into lengths.
Chain brake: A device used to stop the
saw chain.
Chain saw powerhead: A chain saw
without the saw chain or guide bar.
Drive sprocket: The toothed part that
drives the saw chain.
Felling: The process of cutting down a
tree.
Felling back cut: The final cut in a tree
felling operation made on the opposite
side of the tree from the notching
undercut.
Front handle: The support handle located
at or toward the front of the chain saw.
Hand guard: A structural barrier between
the front handle of a chain saw and
the guide bar, which also serves as an
activating mechanism for the chain
brake.
Guide bar: A railed structure that supports
and guides the saw chain.
Kickback: The backward or upward
motion, or both, of the guide bar
occurring when the saw chain near the
nose of the top area of the guide bar
contacts any object such as a log or
branch, or when the wood closes in and
pinches the saw chain in the cut.
Low-kickback chain: A chain that
complies with the kickback performance
requirements of ANSI B..
Normal cutting position: Those positions
assumed in performing the bucking and
felling cuts.
Notching undercut: A notch cut in a tree
that directs the trees fall.
Rear handle: The support handle located
at or toward the rear of the saw.
Reduced kickback guide bar: A guide bar
which has been demonstrated to reduce
kickback significantly.
Saw chain: A loop of chain having
cutting teeth, that cuts the wood, and
that is driven by the powerhead and is
supported by the guide bar.
Trigger lock-out: A movable stop that
prevents the unintentional operation
of the trigger switch until manually
actuated.
Trigger switch: A device that turns the
chain saw on and off.
15
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250 ASSEMBLY
AF 0513  F/N 547361
ASSEMBLY
UNPACKING
DANGER: DO NOT ATTEMPT TO
OPERATE THE CHAIN SAW IF ANY
PART IS DAMAGED OR MISSING.
Some chain saw kits come completely
assembled. If the chain saw has been
packaged without the saw chain and
guide bar installed, see “Replacing the Bar
and Chain in this manual for installation
instructions. After removing the chain
saw from its box, inspect it carefully to
make sure no damage has occurred
during shipping.
Inspect the chain saw for missing parts.
If any parts are damaged or missing,
contact OREGON® to obtain replacement
parts at ...
IMPORTANT: AFTER UNPACKING THE
CHAIN SAW, CHECK THE POSITION OF
THE HAND GUARD. THE CHAIN SAW
WILL NOT RUN WITH THE CHAIN BRAKE
ENGAGED. PULL THE HAND GUARD
BACK TOWARDS THE FRONT HANDLE
BEFORE OPERATION (FIG. ).
INSTALLING BUCKING SPIKES
Some chain saw kits come with metal
bucking spikes as an accessory. To install
the spikes, position on the front of the
saw with the spikes facing upward, then
fasten with the two supplied screws.
FILLING OIL RESERVOIR
CAUTION: CHECK OIL LEVEL
FREQUENTLY AND FILL AS NEEDED.
NEVER OPERATE THE CHAIN SAW IF
OIL IS NOT VISIBLE.
Bar and chain oil is required to properly
lubricate the bar and chain. Use
OREGON® bar and chain oil for best
results. It is specially designed to provide
low friction and faster cuts. NEVER use
oil or other lubricants not specifically
designed for use on the bar and chain.
This can lead to a clogged oil system,
which may cause premature wear of the
bar and chain.
Place the chain saw on its side on a firm,
flat surface, so that the oil cap is on top
(Fig. ). After cleaning any debris from the
cap area, remove the cap and carefully
pour the bar and chain oil into the
reservoir. Replace the cap and check the
presence of oil through the oil inspection
window. Additional bar and chain oil is
necessary shortly after oil is no longer
viewable through the oil inspection
window.
FIG. 6
HAND GUARD IN
OPERATING POSITION
HAND GUARD IN
BRAKE POSITION
FIG. 7
16
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
OPERATING THE SAW
AF 0513  F/N 547361
OPERATING THE SAW
BATTERY PACK AND CHARGER
WARNING: DO NOT CHARGE THE
BATTERY PACK IN THE RAIN.
BATTERY PACK LED CHARGELEVEL
INDICATOR
The lithium ion battery pack is equipped
with an LED charge-level indicator. To test
the charge level of the battery pack, press
the indicator button on the battery packs
face (Fig. ).
No lights: recharge.
One steady green light:
less than % charged.
Charge battery pack before use.
Two steady green lights:
–% charged.
Three steady green lights:
–% charged.
Four steady green lights:
–% charged.
CONNECTING THE CHARGER
Connect the charger cord to the charger
and to the proper electrical outlet (Fig. ).
Only use the cord set that was supplied
with the charger. At first use, verify that
the plug type matches the receptacle.
CHARGER LED CHARGESTATE
INDICATOR
The battery charger is equipped with an
LED charge-state indicator that indicates
the state of charging as well as conditions
that may delay or prevent charging
(Fig. ).
Note: Until a battery pack is inserted, no
lights will be visible.
Blinking orange light: a fault
condition exists. There are
several potential causes. See
Troubleshooting in this manual.
Steady orange light: the battery
pack temperature is beyond the
acceptable range (°F/°C to
°F/°C). Allow the battery pack
to reach the acceptable
temperature range before
charging. The pack may be left on
the charger as the temperature
adjusts. Charging will begin when
the proper temperature is
reached.
Blinking green light: battery pack
is charging.
Steady green light: battery pack is
ready for use.
FIG. 8
INDICATOR LIGHTS
INDICATOR BUTTON
FIG. 9
FIG. 10
17
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250 OPERATING THE SAW
AF 0513  F/N 547361
CHARGING THE BATTERY PACK
WARNING: FAILURE TO FOLLOW
PROPER CHARGING PROCEDURES
MAY CAUSE EXCESSIVE VOLTAGE,
EXCESSIVE CURRENT FLOW, LOSS
OF CONTROL DURING CHARGING,
LEAKAGE OF HAZARDOUS
CHEMICALS, HEAT GENERATION,
BURSTING, OR FIRE.
With the charger cord connected to the
charger and plugged into an electrical
outlet, align the grooves in the battery
with the rails on the charger and slide the
battery pack onto the charger until fully
seated (Fig. ).
Check the charge-state indicator for
charging conditions.
INSERTING AND RELEASING
THE BATTERY PACK
Only use the OREGON® brand battery
packs specified in these operating
instructions.
Align the groove in the battery with the
rails inside the battery port. Firmly insert
the battery pack into the chain saws
battery port, pressing forward until it
clicks as it locks into place (Fig. ).
To remove the battery pack, lift up on
the battery release and remove the pack
(Fig. ).
FIG. 11
FIG. 12
FIG. 13
18
OREGON® CORDLESS TOOL SYSTEM
CHAIN SAW MODEL CS250
OPERATING THE SAW
AF 0513  F/N 547361
GENERAL OPERATION
WARNING: ALWAYS WEAR PROPER
GLOVES, HEAD, EAR, AND EYE
PROTECTION.
OPERATING TEMPERATURE
This chain saw is designed to operate
within a temperature range of °F to
°F (°C to °C).
GRIP
With the saw on a firm, flat surface, grasp
the front handle with the left hand and
the rear handle with the right. Fingers
should wrap over the top of the handle
and the thumb below the handle (Fig. ).
STANCE
Both feet should be on solid ground, with
weight evenly spread between them.
Do not overreach and do not stand on a
ladder, stepstool, or any raised position
that is not fully secured.
STOPPING THE SAW
Release the trigger switch to stop the
chain saw.
TESTING THE BRAKE
Make sure the chain brake is working
before using the chain saw. To check
brake operation, start the saw on a firm
flat surface, and then move the hand
guard forward to manually activate the
chain brake. A properly functioning
chain brake stops the motor and saw
chain immediately.
STARTING THE SAW
Grasp the top and rear handles firmly.
Press and hold the trigger lock-out with
the thumb (). To start the saw, squeeze
the trigger switch () (Fig. ). There is no
need to continue to press the trigger
lock-out.
GRIP WITH THUMB
BELOW HANDLE
FIG. 14
1 TRIGGER LOCKOUT
2 TRIGGER
SWITCH
FIG. 15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90

Oregon Scientific CS250 Original Instruction Manual

Catégorie
Tronçonneuses électriques
Taper
Original Instruction Manual

dans d''autres langues