Polk Audio PSWi225 Le manuel du propriétaire
- Catégorie
- Subwoofers
- Taper
- Le manuel du propriétaire
IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE OPERATING EQUIPMENT
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain
or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.
16. To completely disconnect this equipment from the mains, disconnect the power supply cord plug
from the receptacle.
17. The main plug of the power supply cord shall remain readily operable.
WARNING: Listen Carefully
Polk Audio loudspeakers and subwoofers are capable of playing at extremely high volume levels,
which could cause serious or permanent hearing damage. Polk Audio, Inc. accepts no liability for
hearing loss, bodily injury or property damage resulting from the misuse of its products.
Keep these guidelines in mind and always use your own good judgment when controlling volume:
You should limit prolonged exposure to volumes that exceed 85 decibels(dB).
For more about safe volume levels, go to www.polkaudio.com/education/article/SPL/,
or refer to the Occupational Health and Safety Administration (OSHA) guidelines at
www.osha.gov/dts/osta/otm/noise/standards_more.html.
The CAUTION marks shown here are located
on the back of your PSWi225.
CAUTION: To prevent electric shock, match
wide blade of plug to wide slot, insert fully.
CAUTION: No naked flame sources, such as
candles, should be placed on the apparatus.
Class B Emissions Limits
This Class B digital apparatus meets all requirements of
the Canadian Interference–Causing Equipment Regulations.
Product Disposal
Certain international, national and/or local laws and/or regulations may apply regarding
the disposal of this product. For further detailed information, please contact the retailer
where you purchased this product or the Polk Audio Importer/Distributor in your country.
A listing of Polk Audio Importer/ Distributors can be found on the Polk Audio website
www.polkaudio.com or by contacting Polk Audio at: 5601 Metro Drive, Baltimore,
Maryland 21215, USA. Phone: +1-410-358-3600; in California: 1-800-377-7655.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING STATEMENT
FCC NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
2Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
ENGLISH
Customer Service Hours of Operation: Monday-Friday, 9AM-6PM EST [email protected] 3
FIRST THINGS FIRST
Caution: Subwoofers are heavy. Exercise caution when unpacking your subwoofer.
Please check to ensure you have everything in your Polk Audio
PSWi225 Wireless Subwoofer carton. Inside, you should find:
Take Inventory
• PSWi225 Wireless Subwoofer
• Transmitter
• 5' RCA Cable
• Power Supply For Transmitter
• Owners Manual
• Transmitter Wall Mount Template
• Online Registration Card
If anything is missing or damaged, or if your Polk Audio
PSWi225 fails to operate, please notify your dealer immediately.
We recommend keeping your original carton and packing
materials in case you need to ship the unit in the future.
WHERE TO LOCATE YOUR WIRELESS
SUBWOOFER FOR THE BEST SOUND
The PSWi225 Wireless subwoofer can be placed anywhere in the room, up to 30'
(10 meters) from its transmitter. Your Wireless Subwoofer is really easy to place
and can go just about anywhere in the room. Plus you don’t have to worry about
connecting wires, because the only wire you have to plug in is the power cord
to an AC outlet and the transmitter wires to your receiver or pre-amp.
Note: Placing your subwoofer in a corner of your room will reinforce
the subwoofer’s output, making it sound louder.
We do recommend placing your subwoofer in different locations
within your room to learn what produces the best sound quality
based upon your listening preferences.
Specifications
Dimensions 12 1/2" W x 12 1/2" D x 13" H
(31.75cm x 31.75cm x 33.02cm)
System Power 100 Watts
Subwoofer Weight 21 lbs (9.53kg)
For more information on subwoofer placement, go to:
www.polkaudio.com/education/article.php?id=20.
HOW TO CONNECT YOUR WIRELESS SUBWOOFER
Wireless ID Switches—The Wireless ID Switches, found on both the
subwoofer and the transmitter, select the channel for the wireless signal.
The switch settings change the frequency of the wireless signal the transmitter
sends to the Wireless Subwoofer. The Switch provides four possible settings
in the event there is interference from other devices in your home. The two
switches must be set to the same position for the subwoofer to receive
a signal.
Transmitter Inputs
Audio Inputs—Where you connect your transmitter to your receiver.
Use the 5' analog L/R or LFE audio cable provided.
Wireless ID Switch—Selects the “channel” for the Wireless
Subwoofer signal. Don’t forget to select the same “channel”
on the Wireless Subwoofer itself.
Power Connection—The transmitter power supply is connected here.
LED—Indicates transmitter is active.
Wireless Subwoofer Controls
Volume—Adjusts the volume of the Wireless Subwoofer.
Power Mode LED—Shines green when the Wireless Subwoofer
is on and red when it’s in standby mode or off.
Wireless ID Switch—Selects the “channel”
for the Wireless Subwoofer signal.
Power Switch—Turns the Wireless Subwoofer on and
off, but you can leave it on all the time if you wish.
Low Pass—Adjusts the frequency range over
which the subwoofer operates.
Phase Switch—See page 5.
1
2
3
4
5
6
1
2
3
1
2
3
1
2
3
4
5
6
4
4
AC POWER CONNECTION AND AUTO ON/OFF
Off/Auto/On Switch
Your PSWi225 Subwoofer uses a 3-position power switch, which
selects your subwoofer’s operational mode. The three modes are:
Off, Auto and On.
Off
With the switch in this position, the subwoofer is inactive.
Auto
In the “Auto” position, your subwoofer automatically turns on when it senses
an audio signal and the LED located on the back of the subwoofer will turn green.
We recommend the “Auto” mode if your subwoofer is always receiving
power (i.e., if it’s plugged into a wall outlet). When no signal is present, the
subwoofer will enter a “waiting” state after 15 minutes and the LED will turn red.
On
The subwoofer is always on and fully active in this mode. The LED on the back
of the subwoofer will be green. This mode is best if the subwoofer is plugged
into a switched power outlet.
Note: You may want to leave your subwoofer unplugged during extended
periods of non use, such as during a vacation.
CONNECTING THE SUBWOOFER TO
THE SYSTEM—HOOKUP OPTIONS
IMPORTANT NOTE: USE ONLY ONE OF THESE OPTIONS.
NEVER COMBINE HOOKUP OPTIONS.
OPTION #1 Receivers that include a “SUB OUT” feature—
the most common hookup method with Dolby Digital® and DTS®receivers.
• Connect a single RCA cable from the “SUB OUT” of your receiver
to the LFE input of the transmitter.
• Connect all other speakers directly to the receiver.
• Adjust your receiver’s speaker configurations as follows:
Front Speakers = SMALL
Center and Surrounds = SMALL
Subwoofer = ON, YES, or PRESENT
• Depending on your front speakers’ bass output capabilities, set the crossover
frequency on the receiver to 80Hz for tower and bookshelf speakers (speakers
with a woofer 5 1/4" in diameter or larger) and 100-120Hz for satellite speakers.
Consult your receiver’s owner’s manual for instructions.
WIRELESS TRANSMITTER
WIRELESS SUBWOOFER
SUB-OUT RECEIVER
FRONT REARCENTER
DC 5V 1A
4Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
The two switches
must be set to the
same position for the
subwoofer to receive
a signal.
OPTION #2 Receivers with full-range (unfiltered) left and right “PRE OUT”
jacks (this is the least commonly used hookup).
• Connect the left and right front preamp outputs to the left
and right inputs of the transmitter.
• Adjust the settings on your receiver as follows:
Front Speakers = LARGE
Subwoofer = OFF or NO
ADJUSTING YOUR SUBWOOFER
Note: When you set up your subwoofer for the first time, you will probably have
to make adjustments several times before you hear what you personally like.
FINE TUNING YOUR SUBWOOFER
•Volume: Adjust by ear using a wide variety of CDs and video sources.
Adjust for deep, powerful bass without “boominess.”
• Low Pass Filter Control: NOTE: This control does not operate when
the subwoofer is connected with Option #1 (LFE Input). This control,
which is located on the back of the amplifier, adjusts the frequency range
over which the subwoofer operates. When using smaller main speakers
the upper range of the control will probably yield the best results. With
larger speakers the lower end of the control range will probably sound
best, but always let your ear be the final judge. If male vocals sound
“thin,” turn this control up until the voice sounds rich but not “boomy.”
If male vocals sound too “thick” or chesty,” turn this control down
until the voice sounds natural.
• Phase Switch: Playing music and sitting in your listening position,
carefully listen for the point at which the subwoofer transitions to
your main speakers. This is the crossover point, and this point should
be below the frequency of a male human voice. Whichever phase
setting sounds louder or fuller at the subwoofer’s crossover point
is the optimum setting. Sometimes no difference will be heard.
TROUBLESHOOTING
Subwoofer does – Ensure the subwoofer is plugged
not power on. into a live wall outlet.
– Ensure the rear panel power switch
is in the “On” or “Auto” position.
No sound from – Turn up the volume control.
subwoofer. – Ensure the channel ID switches on the
transmitter and Wireless Subwoofer
are set to the same number.
Bass output not loud enough. – Turn up the Wireless Subwoofer’s
volume control.
– Place the Wireless Subwoofer closer
to a corner of the room.
The Subwoofer’s sound – Turn off both the the transmitter and the
is intermittent, sounds Wireless Subwoofer. Then turn them back
weak or is distorted. on to re-establish communication.
– Try changing settings of the Channel ID
switches on both the transmitter and the
Wireless Subwoofer.
– The Wireless Subwoofer could be too far
away from the transmitter to receive a
sufficiently strong signal. Try moving it closer.
TECHNICAL ASSISTANCE AND SERVICE
If, after following these hookup directions, you experience difficulty, please
double-check all wire connections. Should you isolate the problem to the
subwoofer, contact the authorized Polk Audio dealer where you made your
purchase, or call Polk Audio’s friendly Customer Service Department at
1-800-377-7655 (calls from US or CAN only), 410-358-3600 9am to 6pm EST,
Monday through Friday.
You may also contact us via email: [email protected]. For more detailed
hookup information and manual updates, visit: www.polkaudio.com.
Specifications can be found on the PSWi225 web pages.
Go to www.polkaudio.com.
WIRELESS TRANSMITTER
OUTPUT SUB-OUT RECEIVER
FRONT REARCENTER
DC 5V 1A
WIRELESS SUBWOOFER
Like all wireless devices, your PSWi225 may be susceptible
to RF interference from such sources as microwave ovens,
WiFi computer systems, video game systems, cordless
telephones, blue tooth systems, baby monitors and other
devices. In particular, any devices operating in the 2.4GHz
band may cause intermittent wireless connections between
the PSWi225. It is also possible that your PSWi225 may affect
other wireless systems. For the most part, you can avoid wire-
less performance problems by physically separating these
devices from your PSWi225. Maintaining a distance of several
feet or more between your PSWi225 speaker and any wireless
device should prevent any mutual interference effects. If you do
notice any subwoofer signal dropouts take care to identify the
root cause (most commonly having other wireless devices too
close) and resolve accordingly. Any interference effects from a
microwave oven will cease once the oven stops operating and
may be resolved on a long-term basis by increasing the physical
distance between your PSWi225 and the microwave oven.
A Note Regarding Wireless Performance:
The two switches
must be set to the
same position for the
subwoofer to receive
a signal.
LIMITED WARRANTY
Polk Audio, Inc., warrants to the original retail purchaser only. This warranty will terminate automati-
cally prior to its stated expiration if the original retail purchaser sells or transfers the Product to any
other party.
Polk Audio, Inc., warrants, to the original retail purchaser only, that the LOUDSPEAKER(S), PASSIVE
CROSSOVER COMPONENT(S) and ENCLOSURE on this Polk Audio Loudspeaker Product will be free
from defects in material and workmanship for a period of five (5) years from the date of original retail
purchase from a Polk Audio Authorized Dealer.
Furthermore, Polk Audio, Inc., warrants, to the original retail purchaser only, that any AMPLIFIER OR
OTHER ELECTRONIC COMPONENT that may be included in this Polk Audio Loudspeaker Product will be
free from defects in material and workmanship for a period of three (3) years from the date of original
retail purchase from a Polk Audio Authorized Dealer.
To allow Polk Audio to offer the best possible warranty service, please register your new product
online at: www.polkaudio.com/registration or call Polk customer service 800-377-7655 in
the USA and Canada (outside the USA: 410-358-3600) within ten (10) days of the date of original pur-
chase. Be sure to keep your original purchase receipt.
Defective Products must be shipped, together with proof of purchase, prepaid insured to the Polk
Audio Authorized Dealer from whom you purchased the Product, or to the Factory at 2550 Britannia
Boulevard, Suite A, San Diego, California 92154. Products must be shipped in the original shipping
container or its equivalent; in any case the risk of loss or damage in transit is to
be borne by you. If upon examination at the Factory or Polk Audio Authorized Dealer it is determined
that the unit was defective in materials or workmanship at any time during this Warranty period, Polk
Audio or the Polk Audio Authorized Dealer will, at its option, repair or replace this Product at no addi-
tional charge, except as set forth below. All replaced parts and Products become the property of Polk
Audio. Products replaced or repaired under this warranty will be returned to you, within a reasonable
time, freight prepaid.
This warranty does not include service or parts to repair damage caused by accident, disaster, misuse,
abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage inputs in
excess of the rated maximum of the unit, cosmetic appearance of cabinetry not directly attributable to
defect in materials or workmanship, or service, repair, or modification of the Product which has not
been authorized or approved by Polk Audio. This warranty shall terminate if the Serial number on the
Product has been removed, tampered with or defaced.
This warranty is in lieu of all other expressed Warranties. All implied warranties on this Product are
limited to the duration of this expressed Warranty. Some states do not allow limitation on how long an
implied Warranty lasts, so the above limitations may not apply to you. This Warranty gives you specific
legal rights, and you also may have other rights which vary from state to state.
If this Product is defective in materials or workmanship as warranted above, your sole remedy shall be
repair or replacement as provided above. This warranty does not cover service, parts, or supplies to
repair damage to property other than the Product. In no event will Polk Audio, Inc. be liable to you for
any incidental or consequential damages arising out of the use or in-ability to use the Product, even if
Polk Audio, Inc. or a Polk Audio Authorized Dealer has been advised of the possibility of such damages,
or for any claim by any other party. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above limita-
tion and exclusion may not apply to you.
This Warranty applies only to Products purchased in Canada, the United States of America, its posses-
sions, and U.S. and NATO armed forces exchanges and audio clubs. The Warranty terms and condi-
tions applicable to Products purchased in other countries are available from the Polk Audio Authorized
Distributors in such countries.
GARANTIE LIMITÉE
La garantie de Polk Audio, Inc., n’est valide que pour l’acheteur au détail original. La garantie sera
automatiquement annulée avant sa date d’expiration spécifiée si l’acheteur original vend ou transfère
le produit à tout autre parti.
Polk Audio, Inc., garantit - à l’acheteur au détail original seulement - que le ou les HAUT-PARLEUR(S),
COMPOSANTE(S) DE FILTRE PASSIF et CAISSON(S) de ce produit Polk Audio seront exempts de tout
défaut attribuable aux pièces d’origine et à la main d’oeuvre pour une période de cinq (5) ans à partir
de la date de l’achat au détail original chez un revendeur agréé Polk Audio.
En outre, Polk Audio, Inc., garantit - à l’acheteur au détail original seulement - que TOUT AMPLIFICA-
TEUR OU TOUT AUTRE COMPOSANTE ÉLECTRONIQUE qui pourrait faire partie ce produit Polk Audio
sera exempt de tout défaut attribuable aux pièces d’origine et à la main d’oeuvre pour une période de
trois (3) ans à partir de la date de l’achat au détail original chez un revendeur agréé Polk Audio.
Pour permettre à Polk Audio de vous offrir le meilleur service de garantie possible, veuillez enregistrer
votre nouveau produit en ligne à l’adresse web www.polkaudio.com/registration - ou contactez le
Service à la Clientèle de Polk au 800-377-7655 aux États-Unis et au Canada (à l’extérieur des É.U.:410-
358-3600) dans les dix (10) jours suivant la date de l’achat original. Assurez-vous de conserver votre
reçu d’achat original.
Les produits défectueux doivent être expédiés, avec une preuve d’achat, francs de port et assurés, au
revendeur agree Polk Audio de qui vous avez acheté le produit, ou à l’usine Polk Audio, 2550 Britannia
Boulevard, Suite A, San Diego, California 92154.
Les produits doivent être expédiés dans leur carton d’expédition original ou dans un contenant équiva-
lent. Le propriétaire doit assumer tout risque de perte ou de dommage en transit.
Si, suite à l’examen du produit à l’usine Polk ou chez le marchand agréé Polk Audio, il est déterminé
que la défectuosité est imputable aux matériaux d’origine ou à la main d’oeuvre au cours de la période
de la garantie spécifiée, Polk Audio ou le revendeur Polk Audio, à sa guise, réparera ou remplacera le
produit sans frais additionnels et selon les conditions décrites ci-dessous.
Toute pièce ou produit remplacé devient la propriété de Polk Audio. Les produits réparés ou remplacés
sous la garantie vous seront expédiés francs de port dans un délai raisonnable.
Cette garantie n’inclut pas le service ou les pièces nécessaires à la réparation des dommages provo-
qués par accident, désastre, abus, négligence, mode d'expédition ou emballage inadéquat, utilisation
commerciale, tensions supérieures au maximum prescrit pour l’unité, aspect visuel du meuble non
directement attribuable à un défaut de pièces d’origine ou de main d’oeuvre, ou par le service, la
réparation, ou toute modification du produit qui n’a pas été autorisé ou approuvé par Polk Audio.
Cette garantie sera annulée si le numéro de série sur le produit a été enlevé, altéré ou falsifié.
Cette garantie prend préséance sur toutes autres garanties énoncées. Si la défectuosité de ce
produit est imputable aux pièces d’origine ou à la main d’oeuvre selon les conditions de la garantie
exprimées ci-dessus, votre seul recourt sera la réparation ou le remplacement selon les conditions
décrites ci-dessus.
Dans aucun cas Polk Audio, Inc. pourra-t-elle être tenue responsable pour tout dommage accessoire
ou indirect cause par l’utilisation ou par l’incapacité d’utilisation du produit, même si Polk Audio, Inc.
ou un revendeur agréé Polk Audio, a été avisé de la possibilité de tel dommage, ou pour toute récla-
mation par tout autre parti.
Certains états ne permettant pas l’exclusion ou la limitation des dommages indirects, les limitations
et exclusions exprimées ci-dessus pourraient ne pas s'appliquer dans votre cas.
Toutes les garanties tacites sur ce produit sont limitées à la durée de la garantie énoncée. Certains
états ne permettant pas la limitation de la durée d’une garantie tacite, les limitations ci-dessus pour-
raient ne pas s’appliquer dans votre cas. Cette garantie vous accorde des droits légaux spécifiques;
vous pourriez également avoir d’autres droits qui pourraient varier d’état en état.
Cette garantie s’applique seulement aux produits achetés au Canada, aux États-Unis d’Amérique et
ses possessions, et dans les clubs audio et d’échange des forces armées des É.U. et de l’OTAN. Les
modalités et les conditions de garantie applicables aux produits achetés dans d’autres pays sont
disponibles chez les distributeurs agréés Polk Audio établis dans ces pays.
26 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Polk Audio PSWi225 Le manuel du propriétaire
- Catégorie
- Subwoofers
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Polk Audio PSWi225 Owner's manual
Documents connexes
-
Polk Audio PSWi-8M Manuel utilisateur
-
-
-
-
-
-
-