Extron TLP Pro 300M Series Touch Panel Mode d'emploi
- Taper
- Mode d'emploi
TLP Pro 300M Series • Setup Guide
Overview
The TLP Pro 300M Series touchpanels are 3.5 inch capacitive touchscreens with a resolution of 320x480 (HVGA) and 18-bit color
depth. They can be mounted, in landscape or portrait orientation, to drywall or a standard 1-gang US electrical box.
This guide provides instructions for experienced installers to mount and set up these touchpanels. For complete instructions, see the
TLPPro 300 Series User Guide at www.extron.com.
Setup Checklist
Get Ready
zDownload and install the latest version of the following software:
zGUI Designer — for designing layouts for Extron TouchLink® Pro touchpanels and third party touch interfaces
zGlobal Configurator® Professional or Global Configurator Plus — for setting up and conguring the control processor and
touchpanel
zToolbelt — provides device discovery, device information, rmware updates, and conguration of network settings, system
utilities, and user management for TouchLink Pro devices
zControlScript® Programming software (optional)— for programming Extron control systems
NOTE: All four software programs are available from www.extron.com.
zObtain the following network information from your network administrator:
zDHCP status (on or off). If DHCP is off, you must also obtain:
zIP address zSubnet mask zGateway
zUsername — This can be either admin or user.
zPassword — The factory congured passwords for all accounts on this device have been set to the device serial number.
Passwords can be changed during conguration. Passwords are case sensitive.
NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is extron (for
either admin or user).
zMake a note of the touchpanel MAC address. This can be found on a label attached to the back of the touchpanel.
Mount and Cable All Devices
zMount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on the next page).
zConnect the touchpanel to a Power over Ethernet injector (not provided). Extron recommends the XTP PI 100 power injector,
which must be purchased separately.
zConnect the power injector to the LAN and power it on.
ATTENTION:
• Do not power on the touchpanels until you have read the ATTENTION in the “Rear Panel Features” section of the
TLPPro 300M Series User Guide.
• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «Rear Panel Features » du
TLPPro 300M Series User Guide.
Set up the Touchpanels for Network Communication
zConnect the PC that you are using for setup, the control processor, and touchpanel to the same Ethernet subnetwork.
zUse the Setup Menu (see page 4) or Toolbelt software to set the DHCP status and, if necessary, the IP address, subnet mask,
gateway, and related settings for the touchpanel.
Configure the Touchpanels
zCreate a graphical user interface with GUI Designer (see GUI Designer Help File for step-by-step instructions).
zAssociate functions with the graphical user interface features by conguring (see the Global Configurator Help File) or
programming the system. An Extron-exclusive Python library (ControlScript®) allows you to start programming the system.
1
Product Category
IMPORTANT:
Go to for the
complete user guide and installation
instructions before connecting the
product to the power source.
www.extron.com
Mounting
The following instructions are provided for experienced installers to mount the TLP Pro 300M touchpanel. The touchpanel can be
wall-mounted in either landscape or portrait orientation, using either a standard 1-gang, UL-listed electrical box (must be purchased
separately), or directly into drywall or furniture. Suitable mounting accessories can be found at www.extron.com.
ATTENTION:
• Do not install touchpanels in a re resistant rated wall or partition assembly.
• Ne pas installer les écrans tactiles sur un mur protégé par un dispositif coupe-feu ou dans une cloison.
• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and
national building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes du
bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
Mounting with a UL-listed Electrical Box
The UL-listed electrical junction box must be purchased separately.
1. Cut a hole for the junction box at the required location.
2. If you are using the provided tether kit to deter theft, one loop of
the tether kit should be secured to a wall stud with a screw (not
provided).
3. Run cables to the installation site as required.
4. Pass the other end of the tether kit and the cables
through a knock-out in the junction box.
5. Install the junction box by following the instructions
provided by the manufacturer.
6. Secure the metal mounting plate to the junction box,
using the provided screws.
7. Attach cables to the back of the TLP Pro 300M (see
Rear Panel Features on page 3).
8. If a tether kit is being used, loosen the security screw
on the back panel (see figure 4, F, on page 3)
just enough to insert the loop of the tether kit.
9. Tighten the screw to clamp the tether in place.
10. Attach the touchpanel to the metal mounting plate. The
touchpanel is held in place by magnets.
NORTH
AMERICA
NORTH
AMERICA
Wall
TLP Pr
o 300M
Metal
Mounting
Plate
Electrical
Junction
Box
#6-32 x ¾"
pan-head screws
Figure 1. Mounting to a UL-Listed Electrical Box in the Portrait
Orientation
Mounting to Drywall or Furniture
Figure 2 shows how to mount the TLP Pro 300M in drywall. Follow
the same procedure to mount into furniture.
1. Download the TLP Pro 300M Cut-out Template from
www.extron.com. Ensure that it is printed at 100% size, with
no scaling.
2. Remove the cut-out area from the template.
3. Attach the template to the wall in a suitable location, using a
level to ensure the template is aligned correctly.
4. Use the template to mark and remove the cut-out area (1)
and drill two holes (2) for the screws that
secure the toothed clamping plates.
5. If you are using a tether kit to deter theft, one
loop of the tether kit should be secured to a wall
stud.
6. Run cables to the installation site as required.
7. Secure the metal mounting plate to the
clamping plates, using the provided screws.
As the screws turn, they tighten the grip of the
clamping plates on the inside surface of the
drywall.
8. Attach the tether kit and cables to the
touchpanel and secure the touchpanel to the
mounting plate as described in steps 7 through
10 in the previous section.
TLP Pro 300M
Wall
Metal
Mounting
Plate
Toothed
Clamping
Plate
#6-32 x 1½"
flat-head screws
1
1
1
2
2
2
Figure 2. Mounting to Drywall or Furniture in the Landscape Orientation
2
TLP Pro 300M Series • Setup Guide (Continued)
Rear Panel Features
Figure 4 shows the TLP Pro 300M Series rear panel.
A Status light — Can be programmed to provide system feedback:
zLight red or green zBlink or light continuously
For information about conguring or programming this light, see the
Global Configurator Help File or the Global Scripter Help File.
B Reset LED — Provides feedback about the reset status when the user
presses the Reset button (for an overview, see Reset Modes: A Brief
Summary, on the next page).
C Reset Button — Pressing the Reset button allows the unit to be reset in
any of three different modes (see Reset Modes: A Brief Summary).
D Menu Button — Activates the setup menu (see Setup Menu).
E Serial Number Label — The serial number is on a label on the right edge
of the rear panel, towards the top. The factory congured passwords for
all accounts on this device have been set to this device serial number.
Passwords are case sensitive.
NOTE: If the device is reset to default settings, the password is the
default password conguration. The default password is extron.
F Security Screw — Used to attach provided tether kit. It requires a Torx
screwdriver (size T8).
G LAN/PoE Connector — Connect the touchpanel to a PoE power injector
(not provided) using a twisted pair cable, terminated with an RJ-45
B
B
B
C
C
C
D
D
D
A
A
A
G
G
G
H
H
H
E
E
E
F
F
F
Figure 4. TLP Pro 300M Rear Panel
figure 4
connector. Connect the power injector to the LAN through a network switch. An Extron IP Link Pro control processor must also be
connected to the same network as the TouchLink Pro touchpanel.
See Connecting the Power Injector on the next page.
ATTENTION:
• The TLP Pro 300M is Power over Ethernet (PoE 802.3af, class 2) compliant. Do not power on the touchpanels until you
have read the ATTENTION in the “Rear Panel Features” section of the TLP Pro 300M Series User Guide.
• Le TLP Pro 300M supportent l’alimentation via Ethernet (PoE 802.3af, classe 2). Veuillez lire la partie « Attention » dans la
section « Rear Panel Features » du TLP Pro 300M Series User Guide, avant de mettre sous tension les écrans tactiles.
NOTE: These touchpanels are shipped without a power injector. The power injector must be purchased separately.
H USB Port — One micro-B receptacle supports high-speed USB 2.0.
Front Panel Features
Figure 3 shows the TLP Pro 300M Series front panel.
A LCD touchscreen — The 3.5-inch, 320x480 resolution touchscreen is
made with Corning® Gorilla® Glass, which is stronger and more scratch-
resistant than standard glass, while maintaining touch sensitivity, color
saturation, and brightness.
B Motion sensor — Detects motion between three to ve feet from the
touchpanel, and at least 15° from the center axis.
C Light sensor — Monitors ambient light level and adjusts screen
brightness, based on the settings congured using the Setup Menu (see
the next page).
A
A
A
B
B
BC
C
C
Figure 3. TLP Pro 300M Front Panel
3
Product Category
TLP Pro 300M Series • Setup Guide (Continued)
Reset Modes: A Brief Summary
The TLP Pro 300M Series touchpanels offer the following reset modes:
• Use Factory Firmware: Use this mode with Toolbelt software to replace rmware in the event of conicts arising from
uploading a rmware update. Press and hold the Reset button (see figure 4, C) while applying
power to the unit.
• Reset All IP Settings: Use this mode to reset all network settings without affecting user-loaded les.
Press and hold the Reset button until the Reset LED (B) blinks twice (about 6 seconds). Release
and momentarily press the Reset button again.
• Reset to Factory Defaults: Use this mode to return the touchpanel to factory default settings, including passwords.
Press and hold the Reset button until the Reset LED blinks three times (about 9 seconds). Release
and momentarily press the Reset button again.
NOTES:
• The factory congured passwords for all accounts on this device have been set to the
device serial number. Passwords can be changed during conguration. Passwords are case
sensitive.
• If the device is reset to default settings, the passwords are reset to the default password,
which is extron (for either admin or user).
• Enable or Disable the
DHCP Client:
Use this mode to toggle between DHCP enabled and DHCP disabled.
Press the Reset button ve times, consecutively. After the fth press, do not press the button again
within 3 seconds. If DHCP was enabled, it is now disabled and the Reset LED blinks three times. If
DHCP was disabled, it is now enabled and the Reset LED blinks six times.
Setup Menu
Figure 6 shows the Setup menu Status screen for the TLP Pro 300M.
Press the Menu button (see figure 4, D) to open the Setup menu. Any of the six available
screens (Status, Network, Display, Audio, Project Information, and Advanced) can be
accessed by pressing the menu button in the top left corner of the screen (for more information,
see the TLP Pro 300M Series User Guide).
It may be necessary to scroll down to see all the information on the page (for example, see the
Status screen in gure 6).
STATUS EXIT
Device Information
Model
Part Number
Firmware
Bootloader
Network
TLP Pro 300M
60-1667-02
1.00.0001-003
1.00.0002
IP Address
192.168.254.251
Figure 6. Setup Menu: Status Screen for TLP Pro 300M
Connecting the Power Injector
The power injector must be purchased separately. Figure 5 shows the
Extron XTP PI 100. Your power injector may look different.
Connect a straight-through Ethernet cable from the power injector to a
switch or router (1). This cable carries network information from the
switch or router to the power supply input. A second straight-through
cable (2) carries the network information and 48VDC from the power
injector to the touchpanel LAN/PoE connector (see figure 4, G, on the
previous page). Connect the IEC power cord to a convenient 100 VAC to
240 VAC, 50-60 Hz power source (see gure 5, 3).
100-240V
~
50-60Hz
0.4A MAX
XTP
PWR
XTP PWR
To network switchTo touchpanel
1
1122
2
3
3
3
Figure 5. Connecting to a Power Injector
468-3146-50 Rev. C
07 22
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
For information about replacing and disposing of batteries, see the TLP Pro 300M Series User Guide at www.extron.com.
© 2020 -2022 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
-
1
-
2
-
3
-
4
Extron TLP Pro 300M Series Touch Panel Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Extron TLP Pro 300M Manuel utilisateur
-
Extron TLP Pro 300M Manuel utilisateur
-
-
Extron TLP Pro 525T Manuel utilisateur
-
Extron TLP Pro 1525TG Manuel utilisateur
-
Extron TLP Pro 725M Manuel utilisateur
-
Extron TLP Pro 1520MG Manuel utilisateur
-
-
-
Extron TLP Pro 720C Manuel utilisateur