Murray 629904X54A Instruction book

Catégorie
Souffleuses à neige
Taper
Instruction book
InstructionBook
SnowThrower
Model629904x54A
Q ManueldeI'utilisateur Chasse-neige
module629904x54A
Betriebsanleitung
Schneefriise
Modell629904x54A
Q IstruzioniperI'uso Spazzaneve
Modello629904x54A
Bruksanvisning
Snefreser
modell629904x54A
Anv_ndarhandbok Sn6slunga
modell629904x54A
Ohjekirja
ManualdeInstrucciones
Lumilinko
malli629904x54A
Quitanieves
modelo629904x54A
F-O21033L
4 3
; 15 19
18
/!
\
3_
/:
/
11
\
4
1 5_
16
\ /
4
_6
F-O21033L 2
z _8
2
7 12 6
/
7
\
6
9_
\
lO
1
2
12
F-O21033L 3
/
2
/3
4
/4
4
L5
16
F-O21033L 4
1! 5 6 5 18
1
\
3
2
3
6
6_
2O
21
17
9
4
22
13
F-O21033L 5
4
23
\
6 3
2
24
8
25
26
. p
! mL, 1 f.,l_ m
t I
2!
28
F-O21033L 6
29 30
10
6
5
4
5
3
\
ilillll_
3/
11 3
_,ii¸¸¸¸_
19
20
8
13
17
F-021033L 7
2
©
1 1
rI
2
F-O21033L 8
CONTENTS
PRODUCT INFORMATION 9
OWNER'S INFORMATION 9
INTERNATIONAL PICTORIALS 10
ASSEMBLY 12
OPERATION 12
MAINTENANCE 15
MAINTENANCE CHART 15
TROUBLE SHOOTING CHART 18
TWO YEAR LIMITED WARRANTY
Murray, Inc. warrants to the original purchaser
that this unit shall be free from defects in
material and workmanship under normal use
and service for a period of Two (2) Year from
the date of purchase; however, this warranty
does not cover engines, accessories (such as
electric starters) and Normal Wear Parts (except
as noted below) as the companies that
manufacture these items furnish their own
warranties and provide service through their
authorized field service facilities. For additional
information, see the warranties covering these
particular parts. If you are uncertain whether
your unit contains or is equipped with one or
more of these parts, consult your dealer prior to
purchase. Subject to the terms and conditions
noted in this Limited Warranty, we shall, at our
option, repair or replace at no cost to the original
purchaser any part covered by this Limited
Warranty during the applicable warranty period.
Normal Wear Parts ere defined as drive belts,
augers, shear pins, tires and headlights. These
parts are warranted to be free from defects in
material end workmanship as delivered with the
product. Any claim for repair or replacement of
Normal Wear Parts must be made within thirty
(30) days of the date of purchase. No claims
involving damage caused from material use,
abuse or misuse will be honored.
This Murray, Inc. Two (2) Year Limited
Warranty is your exclusive remedy; however,
this warranty is void or does not apply to any
unit that has been tampered with, altered,
misused, abused or used for rental or other
commercial and/or professional
(non-homeowner) uses. Your warranty does not
cover minor mechanical adjustments which are
not due to any defect in material or
workmanship. For assistance in making such
adjustments, consult your Instruction Book.
To make a claim under this Murray, Inc. Two (2)
Year Limited Warranty, return the unit (or if
authorized in advance, the defective part) along
with your proof of purchase to an Authorized
Service Center near you. To locate the nearest
Authorized Service Center, call the Central Parts
Distributor for your area shown in the list
provided with your unit or check the Yellow Page
listings in your local telephone directory. If you
return the entire unit, we will repair the unit. If we
authorize the return of the defective part only, we
will either replace or repair the part. This Murray,
Inc. Two (2) Year Limited Warranty gives you
specific legal rights, and you may also have
other rights which vary from state to state. This
Limited Warranty is given in lieu of all other
expressed and implied warranties including
the implied warranty of merchantability and
warranty of fitness for a particular purpose. If
you need additional information on this written
warranty or assistance in obtaining service,
write:
RAYTER LIMITED,
Service Department,
Spellbroek,
Bishop's Stortford,
Hertfordshire. CM23 4BU.
MURRAY, INC.
Outdoor Power Equipment
Customer Service Department
P.O. Box 268
Brentwood, Tennessee U.S.A. 37027
1-800-251-8007
PRODUCT INFORMATION
The owner must be certain that all the product
information is included with the unit. This
information includes the INSTRUCTION
BOOKS, the REPLACEMENT PARTS and the
WARRANTIES. This information must be
included to make sure state laws end other laws
are followed.
OWNER'S INFORMATION
This instruction book is written for a person with
some mechanical ability. Like most service
books, not all the steps are described. Steps on
how to loosen or tighten fasteners ere steps
anyone can follow with some mechanical ability.
Read and follow these instructions before you
use the unit.
Know your product: If you understand the unit
and how the unit operates, you will get the best
performance. As you read this manual, compare
the illustrations to the unit. Learn the location
and the function of the controls. To help prevent
an accident, follow the operating instructions
and the safety rules. Keep this manual for future
reference.
IMPORTANT: Many units are not assembled 3.
and are sold in cartons. It is the responsibility of 4.
the owner to make sure the assembly instruc-
tions in this manual are exactly followed. Other
units are purchased in an assembled condition.
On assembled units, it is the responsibility of the 5.
owner to make sure the unit is correctly as-
sembled. The owner must carefully check the
unit according to the instructions in this manual 6.
before it is first used.
7.
8.
mURRAY
t=
WARNING: Look for this symbol to indicate
important safety precautions. This symbol
indicates: "Attention! Become Alert! Your
Safety Is At Risk."
Responsibility Of The Owner
The responsibility of the owner is to
follow the instructions below.
t,
2,
MODEL NO.: 629904x54A
SKU No.:
YYYY MM DD:
SERIAL NO.:
3700 min-1
129 kg
Manufactured in Lawrenceburg, TN 38464, U.S.A.
Carefully read and follow the rules for safe
operation.
Fellow ell the assembly and preparation
instructions.
Inspect the unit.
Make sure that the operator of the unit
knows how to correctly use all standard
and accessory equipment.
Operate the unit only with guards, shields,
and other safety items in place and working
correctly.
Correctly adjust the unit.
Service the unit only with authorized or ap-
proved replacement parts.
Complete all maintenance on the unit.
Environmental Awareness
Do not fill the engine's fuel tank completely
full.
Drain fuel for off-season storage.
Use only unleaded gasoline.
Service the air cleaner regularly.
Change oil regularly. Use 5W-30 oil.
Tuoe-up the engine regularly.
Keep equipment in efficient operating
condition.
Dispose of used engine oil properly.
Declared vibration emission values in accordance with Directive 98/37/E0.
Vibration Emission according to EN 1033;1996:10.6 m/s2.
Values determined at the handle when the machine was operated stationary on a
concrete surface at 3700 mint.
F-021033L
Declared airborne noise emissions of LWA108 dB is in accordance with Directive
2000/14/EC, Annex V.
Sound Pressure Level at operator position 86 dB.
Values determined at ear according to the specifications of EN ISO 11201.
9
INTERNATIONAL PICTORIALS
IMPORTANT: The following pictorials are Io*
cated on your unit or on literature supplied
with the product. Before you operate the
unit, learn and understand the purpose for
each pictorial.
Safety Warning Symbols
DANGER
Thrown Objects.
Keep Bystanders Away.
O
DANGER
Thrown Objects.
Keep Bystanders Away.
IMPORTANT
Read Owner's Manual
Before Operating
WARNING This Machine.
DANGER
Stop The Engine
WARNING Before Unclogging
Hot Surface STOP Discharge Chute!
DANGER
Avoid Injury From
Rotating Auger. Keep
Hands, Feet And
Clothing Away.
36
C0ntr0, And 0perat_0ls ) _ _)
Slow Fast Electric Start Engine Start Engine Run Engine Off
© I H N
Engine Stop On Choke Off Choke On Neutral Forward
T
Reverse Throttle Primer Button Ignition Key
® Q
Ignition Off Ignition On
Push To Engage
Electric Starter
Engage Auger Clutch Auger Collector Discharge DOWN Discharge UP
Discharge LEFT Discharge RIGHT Drive Clutch Fuel Oil Fuel Oil Mixture
Weight Transfer
Lift Handle To Engage
Weight Transfer
Depress Pedal To Disengage
O
Transmission
Ignition Key
Insert To Run, Pull Out To Stop.
F-O21033L 10
Safe Operation Practices for Snow Throwers
IMPORTANT: Safety standards require operator
presence controls to minimize the risk of injury.
Your snow thrower is equipped with such con-
trols. Do not attempt to defeat the function of the
operator presence control under any circum-
stances.
Training
1. Read the operating and service instruction
manual carefully. Be thoroughly familiar with
the controls and the prober use of the equip-
ment. Know how to stop the unit and disen-
gage the controls quickly.
2. Never allow children to operate the equip-
ment. Never allow adults to operate the
equipment without proper instruction,
3. Keep the area of operation clear of all per-
sons, particularly small children and bets.
4. Exercise caution to avoid slipping or falling
especially when operating in reverse.
Preparation
1. Thoroughly inspect the area where the equip-
ment is to be used and remove all doormats,
sleds, boards, wires, and other foreign ob-
jects.
2. Disengage all clutches before starting the en-
gine (motor).
3. Do not operate the equipment without wear-
ing adequate winter outer garments. Wear
footwear that will improve footing on slippery
surfaces.
4. Handle fuel with care; it is highly flammable.
a. Use an approved fuel container.
b. Never remove fuel tank cap or add fuel to
a running engine (motor) or hot engine
(motor).
c. Fill fuel tank outdoors with extreme care.
Never fill fuel tank indoors.
d. Replace fuel cap securely and wipe up
spilled fuel.
e. Never store fuel or snow thrower withfuel
in the tank inside of a building where
fumes may reach an open flame or spark.
Check fuel supply before each use, allow-
ing space for expansion as the heat of the
engine (motor) and/or sun can cause fuel
to expand.
5. For all units with electric starting motors use
alectdc starting extension cords certified
CSA/UL. Use only with a receptacle that has
been installed in accordance with local in-
spection authorities.
6. Adjust the snow thrower height to clear gravel
or crushed reck surface.
7_
a_
9.
Never attempt to make any adjustments
while the engine (motor) is running (except
when specifically recommended by manufac-
turer).
Let engine (motor) and snow thrower adjust
to outdoor temperatures before starting to
alear scow.
Always wear safety glasses or eye shields
during operation or while performing an ad-
justment or repair to protect eyes from foreign
objects that may be thrown from the snow
thrower.
Operation
1. Do not operate this machine if you are taking
drugs or other medication which can cause
drowsiness or affect your ability to operate
this machine.
2. Do not use this machine if you are mentally
or physically unable to operate this machine
safely.
3. Do not put hands or feet near or under rotat-
ing parts. Keep clear of the discharge open-
ing at all times.
4. Exercise extreme caution when operating on
or crossing gravel drives, walks or roads.
Stay alert for hidden hazards or traffic.
5_
After stdking a foreign object, stop the engine
(motor), remove the wire from the spark plug,
thoroughly inspect snow thrower for any
damage, and repair the damage before re-
starting and operating the snow thrower.
6_
If the unit should start to vibrate abnormally,
stop the engine (motor) and check immedi-
ately for the cause. Vibration is generally a
warning of trouble.
7_
Stop the engine (motor) whenever you leave
the operating position, before unclogging the
auger/imbeller housing or discharge chute
and when making any repairs, adjustments,
or inspections.
a_
When cleaning, repairing, or inspecting, make
certain the auger/imbeller and all moving
parts have stopped and all controls are dis-
engaged. Disconnect the spark plug wire and
keep the wire away from the spark plug to
prevent accidental starting.
9_
Take all possible precautions when leaving
the snow thrower unattended. Disengage the
auger/impeller, stop engine (motor), and re-
move key.
10. Do not run the engine (motor) indoors, except
when starting the engine (motor) and for
transporting the snow thrower in or out of the
building. Open the outside deers; exhaust
fumes are dangerous (containing CARBON
MONOXIDE, an ODORLESS and DEADLY
GAS).
11. Do not clear snow across the face of slopes.
Exeralse extreme caution when changing
direction on slopes. Do not attempt to clear
steep slopes.
12. Never operate the snow thrower without
proper guards, plates or other safety protec-
tive devices in place.
13. Never operate the snow thrower near enclos-
ures, automobiles, window wells, drop_3ffs,
and the like without proper adjustment of the
snow discharge angle. Keep children and
pets away.
14. Do not overload the machine capacity by at-
tempting to clear snow at too fast a rate.
15. Never operate the machine at high transport
speeds on slippery surfaces. Look behind
and use care when backing up.
16. Never direct discharge at bystanders or allow
anyone in front of the unit.
17. Disengage power to the collectar/imbeUer
when snow thrower is transported or not in
use.
18.
19.
20.
21.
22.
23.
Use only attachments and accessories ap-
proved by the manufacturer of the snow
thrower (such as tire chains, electric start kits,
ect.).
Never operate the snow thrower without good
visibility or light. Always be sure of your foot-
ing and keep a firm hold on the handles.
Walk;never run.
Do not over-reach. Keep proper footing and
balance at all times.
Exercise caution if operating on steep slop-
ing surfaces.
This snow thrower is for use on sidewalks,
driveways and other ground level surfaces.
Do not use the snow thrower on surfaces
above ground level such as roofs of resi-
dences, garages, porches or other such
structures or buildings.
Maintenance And Storage
1. Check shear bolts and other bolts at frequent
intervals for prober tightness to be sure the
equipment is in safe working condition.
2. Never store the snow thrower with fuel in the
tank inside a building where ignition sources
are present such as hot water and space
heaters, clothes dryers, and the like. Allow
the engine (motor) to cool before storing in
any enclosure.
3. Always refer to operator's guide instructions
for important details if the snow thrower is to
be stored for an extended period.
4. Maintain or replace safety and instruction la-
bels, as necessary.
5. Run the snow thrower a few minutes after
throwing snow to prevent freeze-up of the
anger/impeller.
F-021033L 11
ASSEMBLY
Read and follow the assembly and adjustment
instructions for your snow thrower. All fasteners
are in the parts bag. Do not discard any parts or
material until the unit is assembled.
_k WARNING: Before doing any
assembly or maintenance to the
snow thrower, remove the wire
from the spark plug.
NOTE: In this instruction book, left and right
describe the location of a pert from the oper-
ator's position behind the unit.
NOTE: Torque is measured in foot pounds
(metric N.m). This measurement describes
how tight a nut or bolt must be. The torque is
measured with a torque wrench.
NOTE: Illustrations begin on page 2.
NOTE: Fasteners and loose parts are shown
at full size in Figure 35.
Tools Required
1 Knife
1 Pliers
2 1/2 inch open end wrenches
2 9/I 6 inch open end wrenches
2 3/4 inch open end wrenches
1 Measuring tape or ruler
1 Screwdriver
How To Remove The Snow Thrower
From The Carton
1. (Figure 1) The snow thrower is shown in the
shipping position.
2. Cut and discard the plastic ties that secure
the crank assembly and the speed control
rod assembly.
3. Cut down ell four corners of the carton and
lay the side panels flat.
4. Locate all parts that are packed separately
and remove from the carton.
5. Remove and discard the packing material
from around the snow thrower.
6. (Figure 2) For shipping purposes, the height
adjust skids (7) are attached to the pallet.
Remove the screw (17) that secures each
height adjust skid (7) to the pallet.
7. Hold onto the lower handle and pull the snow
thrower off the pallet.
CAUTION: DO NOT back over cables.
8. Remove the packing material from the han-
dle assembly.
9. Cut the ties that secure the clutch control
cables (1) to the lower handle (2). Move the
cables away from the motor frame.
How To Assemble The Handle And
Crank Assembly
1. (Figure 3) Loosen, but do not remove, the
fasteners (1) in the upper holes of the lower
handle.
2. Remove the fasteners and the crank assem-
bly eyebolt (11) from the lower holes of the
lower handle.
3. (Figure 2) Put the shift lever (5) into first
forward position.
4. (Figure 3) Raise the upper handle (2) to the
operating position.
F-021033L
NOTE: Make sure the cables are not
caught between the upper and lower han-
dle.
5. Install the fasteners and the crank aseembly
eyebelt (11) that were removed in step 2.
DO NOT tighten until all fasteners are in
place,
6. (Figure 5) Attach the crank rod (15) to the
universal joint assembly (16) with the hair
pin (12).
7. (Figure 3) Tighten nut on eye bolt (11).
Make sure eye belt (11) is properly aligned
and the crank (18) can freely rotate.
8. Tighten ell handle fasteners.
How To Install The Speed Control Rod
1. (Figure 4) Attach the speed control rod (1)
to the speed select bracket (2) with flat-
washer (3) and cotter pin (4).
2. Put the speed select lever (5) into the sixth
gear position.
3. (Figure 8) Rotate the shift yoke assembly
(6) counterclockwise (down) until it stops.
4. The length at the trunnion nut (7) and
speed control rod (1) have been
pre-adjusted at the factory. If an adjustment
is required, loosen the jam nut (12). To
lengthen or shorten the speed control rod
(1), turn the trunnion nut (7) to obtain the
correct length. Tighten the jam nut (12).
5. Align the trunnion nut (7) with the hole in
the shift yoke assembly (6). Fasten with
washer (8) and cotter pin (9).
6. (Figure 4) Mount the hex jam nut (10) onto
the speed select lever (5).
7. Attach the handle (11) onto the speed se-
lect lever (5). To lock in position, tighten the
hex jam nut (10) against the bottom of the
handle (11).
8. Make sure the speed select lever (5) func-
tions correctly. Move the speed select lever
(5) through all speeds.
Remote Chute Knob (Figure 11)
1, Assemble remote chute knob (1) onto lever
(3) until snug against nut (2).
2, Make sure lip (4) on the remote chute knob
(1) is pointed toward the engine,
3, Tighten the nut (2) against the bottom of the
remote chute knob (1).
HOW TO Assemble The Chute Deflector
1. (Figure 6) Remove carriage bolt (1).
2. Raise the chute deflector (2) into operating
position (3).
3. Fasten chute deflector (2) to flange (4) with
carriage bolts (1). Make sure to install with
head of the carriage bolts (1) on the inside
of the flange (2).
4. Fasten with washers (5) and Iocknuts (6).
5. Tighten Iocknuts (6) securely.
NOTE: Make sure all carriage bolts in flange
are tight. DO NOT OVERTIGHTEN.
Check The Cables
1, (Figure 7) Check the traction drive cable
(1) and the auger drive cable (2). If the bot-
tom of the cables have become discon-
nected, reinstall the cables.
12
2. (Figure 9) If the top of the cables (5) have
become disconnected from the drive levers
(6), attach the cables (5) to the "Z" fitting
(7).
How To Set The Skid Height (Figure 2)
The snow thrower is equipped with height ed-
justable skids (7) mounted on the outside of the
auger housing (4). To adjust the height of the
skids, see "How To Adjust The Height Of The
Skids" in the Maintenance section.
How To Set The Length Of The Cables
The cables were adjusted at the factory and no
adjustments should be necessary. However. af-
ter the handles are put in the operating position,
the cables can be too tight or too loose. If an
adjustment is necessary, see "How To Check
And Adjust The Cables" in the Service And Ad-
justment section.
How To Assemble The Drift Cutter
(if equipped)
Drift cutters are used to cut a path through snow
deeper than the auger housing.
1. (Figure 10) Remove the fasteners that se-
cure the drift cutters (1) to the auger hous-
ing.
2. Rotate the drift cutters (1) 180 °,
3. Reinstall the fasteners.
How To Prepare The Engine
NOTE: The engine was shipped from the
factory filled with oil. Cheek the level of the
oil. Add oil as needed.
_lk WARNING: Followthe engine
manufacturer's instructions for the
type of fuel and oil to use. Always
use a safety fuel container. Do not smoke
when adding gasoline to the engine. When
inside an enclosure, do not fill with gaso*
line. Before you add fuel, stop the engine.
Let the engine cool for several minutes.
Check the oil. See the engine manufacturer's
instructions for the type of fuel and oil to use.
Before you use the unit, read the information on
safety, operation, maintenance, and storage.
OPERATION
NOTE: Illustrations begin on page 2.
Know Your Snow Thrower (Figure 2)
Read this Instruction Book and safety rules be-
fore operation the snow thrower, Compare the
illustration with your snow thrower to familiarize
yourself with the location of various controls end
adjustments,
Traction Drive Lever (1) - Select the forward or
reverse direction of travel.
Crank Assembly (2) - Changes the direction of
the discharge chute.
Discharge Chute (3)- Changes the distance the
snow is thrown.
Remote Chute Control (4) -Controls the opera-
tion of the discharge chute.
Auger Drive Lever (5) -Starts and stops the au-
ger and impeller (snow gathering and throwing).
Speed Shift Lever (6) - Selects the speed of the
snow thrower.
Height Adjust Skid (7) - Adjusts the ground
clearance of the auger housing.
Ignition Key (8)- Must be inserted to start the en-
gine.
Primer Button (9) - Injects fuel directly into the
carburetor for fast starts in cold weather.
Electric Start Button (10) -On electric start mod-
els, used to start the engine.
Switch Box (11) - On electric start models, used
to attach a 220 volt electric power cord.
Recoil Starter Handle (12) - Use to manually
start the engine.
Throttle Control (13) - Controls the speed of the
engine,
Choke Control (14) - Use to start a cold engine.
Drift Cutters (18) - (if equipped) Cuts a path
through snow higher than the auger housing.
Shear Bolts (t9)-To protect the machine, special
shear bolts are designed to break is an object be-
comes lodged in the auger housing. The use of a
harder bolt will destroy the protection provided by
the shear bolt.
How To Control
The Discharge Of The Snow
_lk WARNING: Never direct the dis-
charge of snow toward bystanders.
_lk ARNING: Always stop the engine
before unclogging the discharge
chute or the auger housing and be-
fore leaving the snow thrower.
1. (Figure 2) Turn the crank assembly (2) to
change the discharge direction of the snow.
2. (Figure 12) Push the remote chute lever (2)
forward to discharge the snow high and far.
Pull the remote chute lever (2) back to dis-
charge the snow down.
How To Stop
The Snow Thrower (Figure 2)
1. To stop discharging snow, release the auger
drive lever (5).
2. To stop the wheels, release the traction
drive lever (1).
3. To stop the engine, push the throttle control
lever (13) to off and remove the ignition key
(5).
How To Go Forward or Backward
(Figure 2)
1. To change the ground speed, first release the
traction drive lever (1) and then move the
speed shift lever (6) to the desired speed.
2. Ground speed is determined by snow condi-
tions. Select the speed by moving the speed
shift lever (5) into the appropriate notch on
the shift lever plate.
Speed 1,2 Wet, Heavy
Speed 3 Light
F-021033L
Speed 4 Very Light
Speed 5, 6 Transport only
3. To go forward, engage the traction drive
lever (1). Maintain a firm hold on the handle
as the snow thrower starts to move forward.
Guide the snow thrower by moving the han-
dle either left or right. Do not attempt to push
the snow thrower.
4. To go backward, release the tractor drive
lever (1).
5. Move the speed shift lever (5) into either
first or second reverse.
6. Engage the traction drive lever (1).
IMPORTANT: Do not move the speed shift
lever (6) while the traction drive lever (1) is
engaged.
How To Throw Snow (Figure 2)
1. Engage the auger drive lever (5).
2. To stop throwing snow, release the auger
drive lever (5).
_k ARNING: The operation of any
snow thrower can result in foreign
objects being thrown into the eyes,
which can result in severe eye damage.
Always wear safety glasses or eye shields
while operating the snow thrower. We rec-
ommend standard safety glasses or use a
wide vision safety mask over your glasses.
HOW TO Use The Wheel Lockout
(Figure 28)
The right wheel is secured to the axle with a
lockout pin. The unit was shipped with the lock-
out pin in the locked position. For ease of ma-
neuverability in light snow conditions, disconnect
the lockout pin as follows.
1. Pull the knob (1) out to disengage the lock-
out pin.
2. To lock in the disengaged position, turn the
knob (1) 1/4 turn (90 degrees).
Before Starting The Engine
1. Before you service or start the engine, famil-
iarize yourseff with the snow thrower. Be
sure you understand the function and loca-
tion of all controls.
2. Chock the tension of the clutch cable before
starting the engine. See "How To Adjust The
Clutch Cable" in the Maintenance section of
this manual.
3. Make sure that all fasteners are tight.
4. Make sure the beight adjust skids are proper-
ly adjusted. See "How To Adjust The Height
Of The Skids" in the Maintenance section of
this manual.
5. Chock the air pressure in the tires. The cor-
rect air pressure is 14 PSI (1 BAR) to 17 PSI
(t.25 BAR). Do not exceed the maximum
amount of air pressure shown on the side of
the tire.
How To Stop The Engine (Figure 2)
To stop the engine, move the throttle control
(3) to the stop position and remove the ignition
key (5). Keep the ignition key (5) in a safe
place. The engine will not start without the igni-
tion key (8).
13
How To Start The Engine (Figure 2)
Models equipped with an Electric Starter
NOTE: An electric starter kit can be added to
recoil start engines. Electric starter kits are
available from your nearest authorized ser-
vice center.
_k ARNING: The starter is equipped
with a three-wire power cord and
plug and is designed to operate on
220 volt A.C. household current. The power
cord must be properly grounded at all times
to avoid the possibility of electrical shock
which can injure the operator. Carefully fol-
low all instructions in the "How To Start The
Engine" section. Make sure that your house
wiring is a three-wire grounded system. If
you are not sure, ask a licensed electrician.
If your house wire system is not a
three-wire grounded system, do not use
this electric starter under any conditions. If
your system is grounded but a three-hole
grounded receptacle is not available to start
the engine, have a three-hole grounded re.
ceptacle installed by a licensed electrician.
To connect a 220 volt A.C. power cord, al-
ways connect the power cord to the switch
box (11) on the engine first. Then, plug the
other end into the three-hole grounded re-
ceptacle. When disconnecting the power
cord, always unplug the end from the
three-hole grounded receptacle first.
How To Start A Cold Engine (Figure 2)
1. Check the engine oil.
2. Fillthe fuel tank with regular unleaded petrol.
See "Row To Prepare The Engine".
3. Make sure the traction drive lever (1) and
the auger drive lever (5) are in the disen-
gaged (released) position.
4. Move the throttle control (13) to the fast
position.
5. Insert the ignition key (8) into the ignition
slot. Make sure the ignition key (8) snaps
into place. Do not turn the ignition key (5).
Remove the extra ignition key and keep in a
safe place.
6. Move the choke control (14)tothe full
choke position.
7. (Electric Start) Connect the power cord to
the switch box (11) located on the engine.
8. (Electric Start) Plug the other end of the
power cord into a three-hole, grounded 220
VOLT, A.C. receptacle. (See the WARNING
in this section).
9. Push the primer button (9). Every time you
push the primer button (9), wait two sec-
onds. For the number of times required to
push the primer button (9), see the engine
manufacturer's instructions.
lO.(Electric Start) Push on the electric start
button (10) until the engine starts. Do not
crank for more than 10 seconds at a time.
The electric starter is thermally protected. If
the electric starter overheats, itwill automati-
cally stop and can only be restarted when it
has cooled to a safe temperature. A wait of
about 5 to 10 minutes is required to allow the
electric starter to cool.
11.(Recoil Start) Rapidly pull the recoil starter
handle (12). Do not allow the recoil starter
handle (12) to snap back. Slowly return the
recoil starter handle (12).
12.If the engine does not start in 5 or 5 tries.
See the "Trouble Shooting Chart" Instruc-
tions.
13.(ElectricStart) When the engine starts, re-
lease the electric start button (10) and
move the choke control (14) to 1/2 choke
position. When the engine runs smoothly,
move the choke control (14) to the Off posi-
tion.
14.(Electric Start) First disconnect the power
cord from the three-hole receptacle. Then,
disconnect the power cord from the switch
box (11).
NOTE: In temperatures below 0°F, allow
the engine to warm up for several minutes
before blowing snow.
15.When throwing snow, always run the engine
with the throttle control (13) in the fast posi-
tion.
,_ WARNING: Never run the engine
indoors or in enclosed, poorly ven-
tilated areas. Engine exhaust con-
tains carbon monoxide, an odorless and
deadly gas. Keep hands, feet, hair and
loose clothing away from any moving parts
located on the engine or the snow thrower.
The temperature of muffler and nearby
areas may exceed 150°F. Avoid these
areas.
How To Start A Warm Engine (Figure 2)
If an engine has been running and is still warm,
leave the choke control (14) in the off position
and do not push the primer button (9). If the
engine fails to start, follow the instructions "How
To Start A Cold Engine".
NOTE: Do not use the primer button (9) to
start a warm engine.
How To Start An Engine With A Frozen Electric
Starter (Figure 2)
If the electric starter is frozen end will not turn
the engine, follow the instructions below.
1. Pull out the recoil starter handle (12) as far
as possible.
2. Quickly release the recoil starter handle
(12). Allow the recoil starter handle (12) to
snap back against the recoil starter.
If the engine still fails to start, repeat the two pre-
vious steps until the engine starts. Then, contin-
ue with the directions "How To Start A Cold
Engine".
To help prevent the possible freeze-up of the
recoil starter and of the engine controls, proceed
as follows after each snow removal job.
1. With the engine running, quickly pull the re-
coil starter handle (12) three or four times
with a continuous full arm stroke. This will
produce a loud clattering sound that is not
harmful to the engine or starter.
2. Stop the engine. Wipe all snow and moisture
from the carburetor cover, control levers and
cables. Also move the throttle control (13),
choke control (14), and recoil starter han-
dle (12) several times.
How To Remove Snow or Debris From
The Auger Housing (Figure2)
_k ARNING: Do not attempt to re-
move snow or debris that may be-
come lodged in auger housing
without taking the following precautions.
1, Release the auger drive lever (5),
2. Move the throttle control (13) to the stop
position.
3. Remove (do not turn) the ignition key (8).
4. Disconnect the spark plug wire.
5. DO not place your hands in the auger hous-
ing (4) or the discharge chute (3). Use a
pry bar to remove any snow or debris.
Snow Throwing Tips
1. Far maximum snow thrower efficiency,
change the ground speed, NEVER change
the engine speed. The engine is designed to
deliver maximum performance at full throttle
and must be run in the fast position at all
times. In deep, freezing, or wet snow, reduce
forward speed. If the wheels slip, else reduce
forward speed.
2. Most efficient snow throwing is accomplished
when the snow is removed immediately after
ff falls.
3. For complete snow removal, slightly overlap
each previous path.
4. Whenever possible, discharge the snow
down wind.
5. For normal usage, set the skids so that the
scraper bar is 1/8" above the skids. For ex-
tremely hard-packed snow surfaces, adjust
the skids upward so that the scraper bar
touches the ground.
6. Rocks and gravel must not be picked up and
thrown by the machine. On gravel or crushed
rock surfaces, set the skids at I-1/4 inch be-
low the scraper bar. See "How To Adjust The
Height Of The Skids" in the Maintenance
section.
7. After each snow throwing job, allow the en-
gine to idle for e few minutes. The snow and
accumulated ice will melt off the engine.
8. Clean the snow thrower after each use.
9. Remove ice, snow end debris from the entire
snow thrower. Flush with water to remove all
salt or other chemicals. Wipe snow thrower
dry.
F-021033L 14
CUSTOMER RESPONSIBILITIES
SERVICE RECORDS
MAINTENANCE CHART
Fill in dates as you Before First Every Every Every
complete regular Each 2 5 10 25 Each Before
service. Use Hours Hours Hours Hours Season Storage SERVICE DATES
Change Engine Oil _/
_i_,.
Check Spark Plug _/
Check Fuel
Check Auger Clutch Cable Adjustment
(See Cable Adjustment)
Lubricate All Pivot Points
4
4
ii__i'!#__!__iis°_i___m¸_',1¸i¸!ii¸¸_i_'i¸!ii__i_i¸i¸¸i_ii_iiii_ili¸¸_.i!!_ii_ilii_ii!ii¸ii¸!_i!iili!¸i__!iii!ii'lli!i_i!._ii_ii_!i!i!i!i¸!i!i_¸!!!i!ii_¸i!¸ii_!!!_i¸_ii_ii.ii!_!i!_ii!i!iil¸i¸i_i!ii,ii_ii¸!_iii!_i_!i!._ii!i!i_ii_ii_i¸!i_i_¸_!i.iiii!il_i!!iiiii!!i¸!iii_i!¸ii_!!_ii¸ii!!!_:!!.!i¸i!!i!!i!_ii_i__i_i_i¸ii_ii!!if!ii!i'!i¸i¸¸i__!__ii__i¸i¸!i_!i_iii_i¸!!_ii_ilii_ii!ii¸ii¸!_i!iili!¸i__!iii!ii'lli!i_i!ii¸iiililii!ii¸iiiili:iiii!iiil¸_!ii¸!il!ii_i!:ili_ii¸i!ii:iii_ii¸i!ii:iii_ii!ii:iii_ii¸i!ii:iii_ii¸i!ii:iiiiii!ii
Lubricate Drive Chains end Sprockets _ _/
MAINTENANCE
NOTE: Illustrations begin on page 2.
Use the following maintenance section to keep
your unit in good operating condition. All the
maintenance information for the engine is in the
engine manufacturer's instructions. Before you
start the engine, read this book.
_k ARNING: Before you make an in-
spection, adjustment (except
carburettor), or repair, disconnect
the wire from the spark plug.
General Recommendations
The warranty on this snow thrower does not cov-
er items that have been subjected to operator
abuse or negligence. To receive full value from
the warranty, the operator must maintain the
snow thrower as instructed in this manual.
Some adjustments must be made periodically to
propedy maintain the snow thrower.
After Each Use
Check for any loose or damaged parts.
Tighten any loose fasteners.
Check end maintain the auger.
Check controls to make sure they ere
functioning properly.
If any parts are worn or damaged, replace
immediately.
All adjustments in the Maintenance section of
this manual should be checked at least once
each season.
F-021033L
As Required
The following adjustment should be preformed
more than once each season.
1. Adjust the auger drive belt after the first 2 to
4 hours, again at mid-season, and twice
each season thereafter. See "How To Adjust
The Auger Drive Belt" in the Maintenance
section.
Lubrication
Every 10 Hours (Figure 17)
1, LubdcatetheZerkfittings (1) everyten
hours with a grease gun.
2. Each time a shear bolt is replaced, the auger
shaft must also be greased.
3. Lubricate ell pivot points.
Every 25 Hours
Chute Rotation Gear
(Figure 5) Lubricate the chute rotation gear (1)
with automotive type oil,
Chains
1, (Figure 2) Move the speed shift lever (6) to
first gear.
2, Remove the gas from the gas tank. Stand
the snow thrower up on the front end of the
auger housing (4).
_k ARNING: Drain the gasoline out-
doors, away from fire or flame.
3, (Figure 24) Loosen the bolts (3) on each
side of the bottom panel (2),
15
4, Remove the bottom panel (2).
5, (Figure 18) Lubricate the chains (5) with a
chain type lubricant.
6, Wipe the hexshaft and sprockets (6) with
5W30 motor oil,
NOTE: If grease or oil come in contact
with the disc drive plate (1) or the friction
wheel (3), damage can result. Clean off
any oil or grease with a alcohol base sol-
vent.
7, (Figure 24) Install the bottom panel (2).
8, Tighten the bolts (3) on each side of the bot-
tom panel (2).
Items Not To Lubricate (Figure 18)
1, De not lubricate the hex shaft and sprock-
ets (6). All bearings and bushings are life-
time ]ubdcated. For storage, put a slight
amount of 5W-30 motor oil on a cloth and
wipe the hex shaft and sprockets (6) to
prevent rust.
2. If grease or oil comes in contact with the
disc drive plate (1) or the friction wheel
(3), the friction wheel (3) can be damaged.
Make sure to thoroughly clean the disc drive
plate (1) and the friction wheel (3).
CAUTION: Any greasing or oiling of the
above components can cause contamina-
tion of the friction wheel (3). If the disc
drive plate (1) or the friction wheel (3) be-
come contaminated with grease or oil,
damage to the friction wheel will result.
3. The auger gear case is lubricated at the fac-
tory and does not require additional lubrica-
tion. If for some reason the lubricant leaks
out, have the auger gear case checked by a
factory authorized service center.
How To Adjust The Height Of The Skids
(Figure 2)
This snow thrower is equipped with two height
adjustable skids (7). These skids elevate the
front of the snow thrower. For normal hard sur-
faces, such as a paved driveway or walk, adjust
the skids as follows.
1. Put the snow thrower on e level surface.
2. Make sure both tires are equally inflated.
The correct air pressure is 14 PSI (1 BAR) to
17 PSI (1.25 BAR). Do not exceed the maxi-
mum amount of air pressure shown on the
side of the tire.
3. Put the extra shear bolts (found in the parts
bag) under each end of the scraper bar (15)
next to the adjustable skids (7).
4. Loosen the mounting nuts (15) that hold the
adjustable skids (7). To bring the front of the
snow thrower down, raise each adjustable
skids (7). Tighten the mounting nuts (16).
NOTE: For rocky or uneven surfaces, raise
the front of the snow thrower by moving the
adjustable skids (7) down.
_lk ARNING: Be certain to maintain
proper ground clearance for the
area to be cleared. Objects such
as gravel, rocks or other debris, if struck
by the impeller, can be thrown with suffi-
cient force to cause personal injury, prop-
erty damage or damage to the snow throw-
HOW TO Adjust
The Scraper Bar (Figure 2)
After considerable use, the scraper bar (15) will
become worn. The scraper bar (15), in con-
junction with the skids, must be adjusted to allow
1/8 inch clearance between the scraper bar
(15) and the sidewalk or area to be cleared.
1. Put the snow thrower on e level surface.
2. Make sure both tires are equally inflated.
The correct air pressure is 14 PSI (1 BAR) to
17 PSI (1.25 BAR). Do not exceed the maxi-
mum amount of air pressure shown on the
side of the tire.
3. Loosen the carriage bolts and nuts that hold
the scraper bar (15) to the auger housing
(4).
4. Adjust the scraper bar (15) to allow 1/8 inch
clearance between the scraper bar (15) end
the sidewalk or area to be cleared.
5. Tighten the carriage bolts and nuts. Make
sure that the scraper bar (15) is parallel with
the sidewalk or area to be cleared.
6. To extended the life of the scraper bar (15),
remove end reverse the mounting of the
scraper bar (15).
How To Remove The Snow Hood
To access the spark plug, the snow hood must
be removed as follows:
1. (Figure 13) Remove the choke control
knob (1).
2. Remove the ON/OFF key (2).
3. Remove the four mounting screws (5).
4. (Figure 14) Slowly remove the snow hood
(4). Make sure that the primer button hose
and the ignition wire are not disconnected.
5. To install the snow hood (4), first make sure
that the primer button hose and the ignition
wire are connected.
F-021033L
6. (Figure 15) Mount the snow hood (4) to the
engine and secure with the four mounting
screws.
7. (Figure 16) Align the tab (5) on the choke
control knob (6) with the slot (7) in the
snow hood.
8. Connect the choke control knob (5) with
the choke shaft (7). Make sure the choke
control knob (5) is propedy installed. If the
choke control knob (6) is not installed cor-
rectly, the choke wii] not operate.
How To Check And Adjust The Cables
The traction drive cable and the auger drive
cable are adjusted at the factory. During normal
use, a cable can become stretched and must be
checked and adjusted as follows.
How To Check The Cables (Figure 19)
1. TOcheck for correct adjustment, disconnect
the "Z" fitting (1) from the drive lever (2).
2. Move the drive lever (2) forward until the
drive lever (2) is contacting the plastic
bumper (3).
3. The control cable is correctly adjusted if the
center of the "Z" fitting (1) isaligned (4)
with the hole in the drive lever (2) and there
in no droop in the cable.
How To Adjust The Auger Drive Cable
1. Remove the gas from the gas tank. Stand
the snow thrower up on the front end of the
auger housing.
,_ WARNING: Drain the gasoline out-
doors, away from fire or flame.
2. (Figure 19) Diseennect the "Z" fitting (1)
from the drive lever (2).
3. (Figure 20) Pull the spring cover up to ex-
pose the spring (5). Push the cable (6)
through the spring (5) to expose the square
end (7) on the cable (6).
4. Hold the square end (7) with pliers and ad-
just the Iocknut (8) in or out until the excess
slack is removed.
5. Pull the cable (5) back through the spring
(5).
6. (Figure 19) Connect the "Z" fitting (1) to the
drive lever (2).
NOTE: When the auger drive belt is adjusted
or replaced, check end adjust the cable.
How To Adjust The Traction Drive Cable
1. Remove the gas from the gas tank. Stand
the snow thrower up on the front end of the
auger housing.
,_ WARNING: Drain the gasoline out-
doors, away from fire or flame.
2. (Figure 24) Loosen the bolts (3) on each
side of the bottom panel (2).
3. Remove the bottom panel (2).
4. (Figure 19) Disconnect the "Z" fitting (1)
from the traction drive lever (2).
5. (Figure 30) Slide the cable boot (3) off the
cable adjustment bracket (4).
6. Push the bottom of the traction control
cable (5) through the cable adjustment
bracket (4) until the "Z" hook (5) can be re-
moved.
16
7. Remove the "Z" hook (6) from the cable
adjustment bracket (4). Move the "Z" hook
(6) down to the next adjustment hole.
8. Pull the traction control cable (5) up
through the cable adjustment bracket (4).
9. Put the cable boot (3) over the cable ad-
justment bracket (4).
lO.(Figure 19) Install the "Z" fitting (1) to the
traction drive lever (2).
11.(Figure 18) To check the adjustment, de-
press the drive lever and check the length
"A" of the drive spring (7). In correct adjust-
ment, the length "A" of the drive spring (7)
is as follows:
minimum 3 inches (76 mm.)
maximum 3-3/8 inches (85 mm.),
12.(Figure 24) Install the bottom panel (2).
13.Tighten the bolts (3) on each side of the bot-
tom panel (2).
HOW TO Adjust The Belts
The belts will stretch during normal use. If you
need to adjust the belts due to wear or stretch,
proceed as follows.
How To Adjust The Auger Drive Belt
If the snow thrower will not discharge snow,
check the adjustment of the auger drive cable.
See "How To Check And Adjust The Cables" in
the Maintenance section, if the adjustment is
correct, then check the condition of the auger
drive belt. If the auger drive belt is damaged,
replace the auger drive bolt. See "How To Re-
place The Belts" in the Maintenance section, if
the auger drive belt is loose, adjust as follows.
1. Disconnect the spark plug wire.
2. (Figure 21) Remove screw (2) from belt
cover (1). Remove the belt cover (1).
3. (Figure 22) Loosen the nut (2) on the idler
pulley (3) Move the idler pulley (3) 1/8 inch
toward the auger drive belt (4).
4. Tighten the nut (2).
5. (Figure 23) Depress the auger drive lever.
Check the tension on the auger drive belt
(4). In correct adjustment, the auger drive
belt (4) will deflect 1/2 inch (5) with moder-
ate pressure. If the adjustment is not correct,
repeat the adjustment.
6. (Figure 21) install the belt cover (1). Tighten
screw (2).
7. Check the adjustment of the auger drive
cable. See "How To Check And Adjust The
Cables" in the Maintenance section.
8. Attach the spark plug wire.
Traction Drive Belt
The traction drive belt has constant spring pres-
sure and does not require an adjustment. If the
traction drive bolt is slipping, replace the belt.
See "How To Replace The Belts" in the Mainte-
nance section.
How To Replace The Belts
The drive belts ere of special construction and
must be replaced with original factory replace-
ment belts available from your nearest autho-
rized service center.
Some steps require the assistance of a second
person.
How To Remove the Auger Drive Belt
If the auger drive belt is damaged, the snow
thrower will not discharge snow. Replace the
damaged belt as follows.
1.Disconnectthesparkplug wire.
2. (Figure 24) Loosen the bolts (3) on each
side of the bottom panel (2).
3. Remove the bottom panel (2).
4. (Figure 21) Remove screw (2) from belt
cover (1). Remove the belt cover (1).
5. (Figure 22) Loosen the belt guide (9). Pull
the belt guide (9) away from the auger
drive pulley (10).
6. Pull the idler pulley (3) away from the au-
ger drive belt (4).
7. Remove the old auger drive belt (4) from
the auger drive pulley (10) end from the en-
gine pulley (11). Replace the auger drive
belt (4) with an original factory replacement
belt available from an authorized service
center.
8. Install the new auger drive belt (4) onto the
auger drive pulley (10) and onto pulley
(11).
9. Adjust the auger drive belt (4). See "How To
Adjust The Auger Drive Belt" in the Mainte-
nance section.
10.Adjust the belt guide (9). See "How To Ad-
just The Belt Guide" in the Maintenance sec-
tion.
11.(Figure 21) Install the belt cover (1). Tighten
screw (2).
12.Check the adjustment of the cables. See
"How To Check And Adjust The Cables" in
the Maintenance section.
13.Connect the spark plug wire.
How To Remove the Traction Drive Belt
If the snow thrower will not move forward, check
the traction drive belt for wear or damage. If the
traction drive belt isworn or damaged, replace
the belt as follows.
1. Disconnect the spark plug wire.
2. Remove the auger drive belt. See "How To
Remove The Auger Drive Belt" in the Mainte-
nance section.
3. (Figure22) Removethe e-ring (17) from
one end of the swing plate axle rod (18).
Remove the swing plate axle rod (18) to
allow the the swing plate to pivot forward.
4. Remove the traction drive spring (16).
5. Remove the old traction drive belt (13) from
the traction drive pulley (14) and from the
engine pulley (15). Replece the traction
drive belt (13) with an original factory re-
placement belt available from an authorized
service center.
6. Install the new traction drive belt (13) onto
the traction drive pulley (14) and onto en-
gine pulley (15).
7. Make sure the traction drive idler pulley
(12) is properly aligned with the traction
drive belt (13).
8. Attach the traction drive spring (16).
9. Install the swing plate axle rod (18) end se-
cure with the e-ring (17) removed earlier.
lO.(Figure 33) The bottom of the swing plate
(20) must be positioned between the align-
merit tabs (19). Make sure the swing plate
(20) is properly secured.
NOTE: It the drive will not engage after
the traction drive belt has been replaced,
then check to make sure that the swing
plate is positioned between the alignment
tabs (19).
F-021033L
11.(Figure 22) Install and adjust the auger
drive belt (4). See "How To Remove The
Auger Drive Belt" in the Maintenance section.
12.Adjust the belt guide (5). See "How To Ad-
just The Belt Guide" in the Maintenance sec-
tion.
13.(Figure 24) Install the bottom panel (2).
14.Tighten the bolts (3) on each side of the bot-
tom panel (2).
15.(Figure 21) Install the belt cover (1). Tighten
screw (2).
16.Check the adjustment of the cables. See
"How To Check And Adjust The Cables" in
the Maintenance section.
17.Connect the spark plug wire.
How To Adjust The Belt Guide
1. Disconnect spark plug wire.
2. (Figure 21) Remove screw (2). Remove the
belt cover (1).
3. (Figure 2) Engage the auger drive lever (5).
4. (Figure 25) Measure the distance between
the belt guide (2) and auger drive belt (3).
The correct distance (4) is 1/8 inch (3.175
ram),
5. If an adjustment is necessary, loosen the
mounting bolt for the belt guide (2). Move
the belt guide (2) to the correct position
(4). Tighten the mounting bolt for the belt
guide (2).
6. (Figure 21) Install the belt cover (1). Tighten
screw (2).
7. Connect the spark plug wire.
How To Adjust Or Replace The Friction
Wheel
How To Check The Friction Wheel
If the snow thrower will not move forward, check
the traction drive belt, the traction drive cable or
the friction wheel. If the friction wheel is worn or
damaged, it must be repleced. See "How To
Replace the Friction Wheel" in this section. If the
friction wheel is not worn or damaged, check as
follows.
1. (Figure 2) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
_k ARNING: Drain the gasoline out-
doors, away from fire or flame.
2. Disconnect the spark plug wire.
3. (Figure 24) Loosen the bolts (3) on each
side of the bottom panel (2).
4. Remove the bottom panel (2).
5. (Figure 2) Position the shift speed lever (6)
in the lowest forward speed.
6. (Figure 26) Note the position of the friction
wheel (4). The correct distance "A" from the
right side of the friction wheel (4) to the out-
side of the motorbox is as follows:
Tire Size Distance "A"
12 and 13 inch 4-1/8" (10.5 cm.)
16 inch 4-5/t6" (10.95 cm.)
If the friction wheel (4) is not in the correct
position, adjust as follows.
How To Adjust The Friction Wheel
1. (Figure 2) Position the shift speed lever (6)
in the lowest forward speed.
17
2. (Figure 8) Remove washer (8) and cotter
pin (9) that connect the trunnion nut (7) to
the shifter rod (1). Remove the trunnion
nut (7) from the shifter rod (1).
3. (Figure 26) Move the friction wheel (4) to
the correct position.
4. (Figure 8) Tum the trunnion nut (7) until it is
aligned with the mounting hole in the shifter
rod (1). When aligned, attach the trunnion
nut (7) and secure with washer (5) and cot-
ter pin (5).
5. (Figure 24) Install the bottom panel (2).
6. Tighten the bolts (3) on each side of the bot-
tom panel (2).
How To Replace The Friction Wheel
If the friction wheel iswom or damaged, the
snow thrower will not move forward. The friction
wheel must be replaced as follows.
1. (Figure 2) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
_k ARNING: Drain the gasoline out-
doors, away from fire or flame.
2. Disconnect the spark plug wire.
3. (Figure 31) Remove the fasteners that se-
cure the left wheel (10). Remove the left
wheel (10) from the axle (11).
4. Loosen the bolts (3) on each side of the bot-
tom panel (2).
5, Remove the bottom panel (2).
6, (Figure 32) Remove the fasteners that se-
cure the drive sprocket (12) to the axle (11).
7, Remove the right wheel, axle (11), end drive
sprocket (12).
8, (Figure 33) Remove the four bolts (16) that
holdthe bearings (7) on each side of the
hex shaft (8).
9, (Figure 34) Remove the hex shaft (8) end
bearings (7).
NOTE: Take special note of the position of
the washers (17).
lO.(Figure 29) Remove the three fasteners (4)
that hold the friction wheel (5) to the hub
(6).
11.(Figure 29) Remove the friction wheel (5)
from the hub (6). Slip the friction wheel (5)
off the hax shaft (8).
12.Assemble the new friction wheel (5) onto
hub (6) with the fasteners removed eedier.
13.(Figure 34) install the hax shaft (8) and
bearings (7) with the four bolts removed ear-
lier.
Make sure the washers (17) are properly
installed in the original position. Also,
make sure the two washers (13) are prop-
erly aligned with the actuator arms (14).
14.Make sure the hex shaft (8) turns freely.
15.(Figure 32) Install the right wbeel, axle (11),
and drive sprocket (12) with the fasteners
removed earlier. Install the chain (15) onto
the drive sprocket (12).
16.Check the adjustment of the friction wheel.
See "How To Adjust The Friction Wheel" in
this section.
17.Make sure the fdction wbeel and the disc
drive plate are free from grease or oil.
18.(Figure 24) Install the bottom panel (2).
19.Tighten the bolts (3) on each side of the bot-
tom panel (2).
20.Install the left wheel (10) to the axle (11)
with the fasteners removed earlier.
21.Connectthesparkplugwire.
How To Replace the Auger Shear Bolt
The augers are secured to the auger shaft with
special shear bolts. These shear belts ere de-
signed to break and protect the machine ff an
object becomes lodged in the auger housing.
Do not use a harder bolt as the protection pro-
vided by the shear bolt will be lost.
_k ARNING: For safety and to pro-
tect the machine, use only original
equipment shear bolts.
To replace a broken shear bolt, proceed as fol-
lows. Extra shear bolts were provided in the as-
sembly parts beg.
1. (Figure 2) Move the throttle control (13) to
the stop position. Disengage all controls.
2. Disconnect the spark plug wire. Make sure
ell moving parts have stopped.
3. (Figure 17) Lubricate the auger shaft Zerk
fitting (1), if equipped, with a grease gun.
4. (Figure 27) Align the hole inthe auger with
the hole in the auger shaft. Install the new
shear bolt (2), spacer (3), and Iocknut (4).
5. Connect the spark plug wire.
HOW TO Prepare The Snow Thrower For
Storage
,_ WARNING: Do not remove gasoline
while inside a building, near a fire,
or while you smoke. Gasoline
fumes can cause an explosion or a fire.
1. Drain the fuel tank.
2. Let the engine run until it is out of gasoline.
3. Drain the oil from the warm engine. Fill the
engine crankcase with new oil.
4. Remove the spark plug from the cylinder.
Pour one ounce of oil into the cylinder. Slow-
ly pull the recoil-start grip so that the oil will
protect the cylinder. Install a new spark plug
in the cylinder.
5. Thoroughly clean the snow thrower.
6. Lubricate all lubrication points. See the Main-
tenance section.
7. Be sure that ell nuts, bolts end screws are
securely fastened. Inspect all visible moving
parts for damage, breakage and wear. Re-
place if necessary.
8. Cover the bare metal parts of the blower
housing, auger, and the impeller with spray
rust preventative lubricant.
9. Put the unit in a building that has good ven-
tilation.
10. If the machine must be stored outdoors.
block up the snow thrower to be sure the en-
tire machine is off the ground.
11.Cover the snow thrower with a suitable pro-
tective cover that does not retain moisture.
Do not use plastic.
How To Order Replacement Parts
The replacement parts ere shown either on the
back pages of this Instruction Book or in a sepa-
rate Parts List Book.
Use only manufacturer's authorized or approved
replacement parts. The letter placed on the end
of the part number denotes the type of finish for
the part, C for chrome, Z for zinc, a PA for pur-
chased assembly. It is important that you include
this when ordering a part. Do not use attach-
ments or accessories not specifically recom-
TROUBLE SHOOTING CHART
mended for this unit. in order to obtain proper
replacement parts you must supply the model
number (see nameplate).
Replacement parts, except for the engine, trans-
mission, transaxle or differential, are available
from the store where the product was pur-
chased, a service shop recommended by the
store or from a"Murray, Inc. Central Parts Dis-
tributor" listed on the back page of this Instruc-
tion Book.
If you are unable to obtain parts or service in the
manner outlined above, then contact:
HAY'rER LIMITED,
Service Department,
Spellbrook,
Bishop's Stortford,
Hertfordshire. CM23 4BU.
MURRAY, INC.
Outdoor Power Equipment
Customer Service Department
P.O. Box 268
Brentwood, Tennessee U.S.A. 37027
1-800-251-8007 Collect telephone calls will not
be accepted.
Replacement parts for the engine, transaxle, or
transmission, are available from the manufectur-
er's authorized service centre found in the yel-
low pages of the telephone directory. Also, see
the individual engine or transmission warranties
to order replacement parts.
When ordering the following information is re-
quired:
(1) The Model Number
(2) Serial Number
(3) Part Number
(4) Quantity
TROUBLE
Difficult starting
CAUSE
Defective spark plug,
Wateror dirt in fuel system,
Unit fails to discharge snow
Engine runs erratic Blocked fuel line, empty gas tank. or stale
gasoline
Engine stalls Unit running on CHOKE.
Engine runs erratic; Water or dirt in fuel system.
Loss of power
Excessive vibration Loose parts: damaged impeller
Unit fails to propel itself Drive belt loose or damaged.
Incorrect adjustment of traction drive cable
Worn or damaged friction wheel.
Auger drive belt loose or damaged.
Auger control cable not adjusted correctly.
Shear bolt broken
Discharge chute clogged.
F-021033L
Foreign object lodged in auger
18
CORRECTION
Replace spark plug.
Use carburetor bowl drain to flush and refill with
fresh fuel.
Clean fuel line; check fuel supply; add fresh
gasoline
Set choke lever to RUN position.
Use carburetor bowl drain to flush and refill with
fresh fuel.
Stop engine immediately and disconnect spark
plug wire. Tighten all bolts and make all
necessary repairs. If vibration continues, have
the unit serviced by a competent repairman.
Replace drive belt.
Adjust traction drive cable.
Replace friction wheel.
Adjust auger drive belt; replace if damaged.
Adjust auger control cable.
Replace shear bolt
Stop engine immediately and disconnect spark
plug wire. Clean discharge chute and inside of
auger housing.
Stop engine immediately and disconnect spark
plug wire. Remove object from auger.
SOMMAIRE
INFORMATIONS SUR LE PRODUIT
INFORMATIONS DESTINEES AU PROPRIETAIRE
PICTOGRAMMES INTERNATIONAUX
MONTAGE
FONCTIONNEMENT
MAINTENANCE
TABLEAU DE MAINTENANCE
TABLEAU DE DEPANNAGE
20
20
21
23
24
26
26
30
Q
GARANTIE LIMITEE DE DEUX ANS
Murray, Inc. garantie aupr_s de racheteur initial
qua cette machine est d_pourvue de d_fauts
mat6riels at de construction sous utilisation et
entretien normaux pendant une dur_e de deux
(2) ans& partir de la date d'acquisitian ; cette
garantie cependant ne cauvre pas les mateurs,
accessoires (tels qua moteurs _lectriques) et
pi_ces d'usure normale (except_es les pi_ces
mentionn_es ci-dessous) 6tant donn_ que les
soci_t6s fabriquant ces articles offrent leurs
propres garanties at fournissent des r6parations
par lebiais de leurs centres de maintenance
specialists agr_s. Pour plus d'infarmations, se
reporter aux garanties couvrant ces pi_ces
particuli_res. Si vous ne savez pas si votre
machine cantient ou est 6quip_e d'une au
plusieurs de ces pi_ces, adressez vous a votre
revendeur avant I'acquisition. Sous r_serve des
madalit_s et conditions de cette garantie limit_e,
nous nous engageons & r_parer ou remplacer, &
notre discr6tian et gratuitement aupr_s de
I'acheteur initial, taute piece cauverte par cette
garantie limit_e jusqu'& I'expiration de la garantie
applicable.
Les pi_ces d'usure normale camprennent les
courraies d'entrainement, les fraises
h_licafdales, les goupilles de cisaillement, les
pneumatiques, etles phares. Ces pi_ces sont
garanties sans d_faut materiel ou de
construction dans 1'6tat o_ elles ant _t6 livr_es
avec ]e produit. Toute r_clamation concernant la
r_paration au le remplacement d'une piece
d'usure narmale dolt _tre effectu_e darts les
trente (30) jaurs suivant la date d'acquisition.
Aucune r_clamation ne sara honor_e
concemant des dommages provenant de la
simple utilisation, d'un usage abusif, ou d'une
mauvaise utilisatian.
Cette garantie Murray, Inc. de deux (2) arts
constitue votre recours exclusff ; cepondant,
cette garantie est nulle ou ne s'applique pas aux
machines ayant 6t_ madifi_es, endornmag_es,
fait robjet d'une utilisation abusive, ou utilis6es
lots d'une location au a des fins cammerciales
F-021033L
et/ou professionnelles (autre que domestiques).
Votre garantie ne couvre pas les r_glages
m_caniques mineurs non dus & des d6fauts
materiels de fabrication. Consultez votre manuel
d'utilisation pour obtenir une assistance
concernant ces r_giages.
Pour effectuer une r_clamation sous la garantie
limit_e de deux (2) ans Murray, Inc., retourner
la machine, (ou, suivant notre autorisation
pr6alable, la piece d_fectueuse) accompagn6e
de votre preuve d'achat, aupr_s du Centre de
maintenance agr_6 ]e plus proche de chez vous.
Pour Iocaliser le centre de maintenance le plus
proche, contactez le Distdbuteur de pi_ces
r_gional de votre r_gion figurant sur la liste
fournie avec votre machine, ou consultez les
pages jaunes de votre annuaire t61_phonique
local. Si vous nous retournez la machine
complete, nous r_parerons celle-ci. Si nous
autorisons seulement le retour de la pi6ce
d_fectueuse, nous effectuerons soit la r6paration
de celle-ci, salt son remplacement. Cette
garantie limitee Murray, Inc. de deux (2) arts
vous octroie des droits I_gaux sp_cifiques, et
vous pouvez _galement vous pr6valoir d'autres
droits dont le contenu varie selon I'Etat ot_ils
s'appliquent. Cette garantie limit_e eat
d_livr_e en lieu et place de toute garantie
stipul_e ou tacite, ceci incluant la garantie
tacite de commerciabilite et la garantie de
fonctionnalit_ pour une t&che d_finie. Si
vous souhaitez recevoir des informations
suppl_mentaires concernant carte garantie
_crite ou une assistance quant & robtention de
services de r_paration, adressez=vous & :
HAYTER LIMITED,
Service Department,
Spellbrook,
Bishop's Stortford,
Hertfordshire. CM23 4BU.
MURRAY, INC.
Outdoor Power Equipment
Customer Service Department
P.O. Box 268
Brentwood, Tennessee U.S.A. 37027
1-800=251-8007
19
INFORMATIONS SUR LE PRODUIT
Le propri6taire dolt _tre certain qce tousles
renseignements sur le produit sent inclus avec
la tondecse. Ces renseignements comprennent
les MANUELS D'INSTRUCTION, les PIECES
DE RECHANGE, et les GARANTIES. Ces
renseignements doivent 6tre inclus pour
s'asscrer que les lois d'Etat et les autres lois
sont observ6s.
INFORMATIONS DESTINEES AU
PROPRIETAIRE
Ce manuel se dirige aux personnes familiaris6es
avec ce genre de manipulations m_caniques. La
plupart des ouvrages de maintenance ne
mentionnent pas toutes les _tapes, et cet
ouvrage ne fait pas exception. Serrer ou
desserrer des attaches sent des manipulations
que tout le monde peut effectuer avec une
certaine pratique. Lisez et suivez ces
instructions avant d'utiliser la tondecse.
Apprenez b maitriser I'appareil : si vous
comprenez ]e fonotionnement de oe mod&le,
vous en obtiendrez les meiUecres performances.
Au fur et b mesure que vous lisez le manuel,
reportez-vous aux illustrations. Sachez rep_rer
I'emplacement des commandes et leur fonction.
Afin de pr6venir tout risque d'accident, observez
les instructions de fonctionnement et les r6gles
de s_curit_. Conservez ce manuel pour future
r_f_rence.
IMPORTANT : De nombrecx appareils ne sent
pas assembles et sent vendus d_mont_s dans
lecr carton d'emballage. IIest alors de la
responsabilit6 du propri_taire de veiller & ce qce
les instructions de montage pr_sentes dans le
manuel soient suivies en toute exactitude.
D'autres appareils sont vendus enti_rement
months. En ce qui conceme les machines d_j&
mont_es, il est de la responsabilit_ du
propri6taire de veilier ace que la machine soit
correctement assembl_e. Le propri6taire doit
v_rifier attentivement la machine en fonction des
instructions pr6sentes dans le manuel avant de
commencer &utiliser celle-cL
DANGER : rep_rez ce symbole qui voes
indiquera les precautions de s_curit_ im-
porfantes. Ce symbole signifie : "Attention!
Soyez prudent! Vous encourrez des ris-
ques."
Responsabilite de rutilisateur
La responsabilite de I'utilisateur est de
suivre les instructions ci-dessous.
1, Life soigneusement oe manuel et suivre les
r_gles indiqu_es pour un usage de la ton-
deuse en toute s_curit6.
2. Suivre les instructions de montage et de
preparation.
Q
3. Inspecter ]a tondeuse.
4. S'asscrer que rutilisatecr de la tondeuse
salt bien utiliser les _quipements standards
et les accessoires.
5. N'utiliser la tondeuse qu'avec les 6quipe-
ments de protection, les _crans et autres
dispositifs de s_curit_ bien en place et en
bon _tat de marche.
6. Proceederaux r_glages n_cessaires.
7. Entretenir la tondeuse avec les pi_ces de
rechange autods6es ou agr_es.
8. Veiller & ce qu'un entretien complet soit ef-
fectu_ scr la tondeuse.
Prise de conscience environnementale
Ne pas remplir le r_servoir d'essence du
moteur au ras-bord.
Vider I'essence pendant le remisage hors
saison.
N'utiliser qce de ressence sans plomb.
Entretenir r_guli6rement le filtre a air.
Changer I'huile r_guli6rement. Utiliser de
rhuile de grade 5W-30.
Effectuer un r6glage du moteur r_guli6re-
ment.
Conserver le mat6riel en bon 6tat de mar-
che.
Eliminer I'huile de vidange de fagon 6colo-
gique.
mURRAY
MODEL NO.: 629904x54A
SKU No.:
YYYY MM DD:
SERIAL NO.:
3700 min-1
129 kg
Manufactured in Lawrenceburg, TN 38464, U.S.A.
Niveaux de vibration d_clar_s conformes &ceux d_finis par la directive
europ_enne 98/37/CE.
Niveaux de vibration relev_s conform_ment a la norme
EN 1033;1996 : 10,6 m/s2.
Valeurs determin_es sur les brae de la tondeuse en station immobile sur une
surface ciment_e &un r_gime de 3700 min-1.
Niveaux de bruit de LWA108 dR declares conformes & ceux d_finis par la
directive europ_enne 2000/14/CE, Annexe V.
Niveau de pression acoustique a la station de rutilisateur 86 dB.
R_sultats & I'oreille obtenus en application de la norme EN ISO 11201.
F-021033L 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124

Murray 629904X54A Instruction book

Catégorie
Souffleuses à neige
Taper
Instruction book

dans d''autres langues