Midmark 641 Power Procedures Chair Guide de référence

Midmark
Marque
Midmark
Modèle
641 Power Procedures Chair
Taper
Guide de référence
Home Function
This function automatically lowers the base so that your patient
may easily mount or dismount the chair.
To lower the base to 23 in. (58 cm)...
Press, then immediately release the Home button.
To lower the base to 19 in. (48 cm)...
Press & hold the Home button until you hear a single “beep”.
QuickChair™ Function (w/foot control only)
This function activates the Base Down, Tilt Down,
Foot Down, & Back Up functions at the same time.
To activate the QuickChair™ function...
Press & hold the QuickChair
™
button on the foot control.
Programming Chair Positions (programmable models only)
This feature allows you to easily recall frequently used chair positions.
To program a chair position...
A. Move the chair to desired position.
B. Press the Program button. [single “beep”]
C. Press the desired Position button (1, 2, 3, or 4). [three “beeps”]
Tip: You must press the Position button within 5 seconds of pressing
the Program button.
To recall a programmed position...
Press & hold the desired Position button (1, 2, 3, or 4).
To operate the Base / Back / Tilt / Foot functions...
Press & hold the appropriate button.
Example: The Foot Up button is called out in the illustration.
Note
If the chair “beeps” and one or more functions will not operate,
move the foot extension to the stowed position - then retry function.
Refer to the ‘Troubleshooting’ section in the User Guide for further
information regarding the Crash Avoidance System.
Note
To stop movement of any automatic chair function...
Press the Stop button on the hand or foot control.
This guide outlines basic operation of the chair.
The enclosed User Guide provides additional
instructions on operation and care, as well as
regulatory compliance information. If service is
required,contact your authorized Midmark dealer.
© Midmark Corporation 2007
Quick Reference Guide
641
Power Procedures Chair
Model Number:
Serial Number:
Dealer Info:
Purchase Date:
Upholstery Color:
003-1707-00 Rev. D 7/9/15
Maintenance
Periodically inspect the following:
• Power cord must be free of visible damage.
• All fasteners must be present and secure.
• All mechanical functions should operate.
Cleaning
Upholstery
Wash your upholstery weekly with a mild liquid
soap and water mixture, rinse with clear water and
dry completely to remove disinfection cleaner build-
up.
Disinfect your upholstery with a solution of stan-
dard bleach and water mixed 1 in 10 (10%) or
chlorine based cleaners. Follow this with a clear
water rinse and thorough drying of material. See
current CDC Guideline for Disinfection & Steriliza-
tion in Healthcare Facilities.
To minimize damage caused by disinfectant
cleaner residue build-up, do not allow disinfectants
to pool on the upholstery surface. Once the
approved contact time has been obtained, remove
and dry excess liquid remaining on the surface.
Detailed care and maintenance instructions are
included with your product. This information is also
available on www.midmark.com in the Technical
library under the User Information tab for your
product.
Painted Metal / Plastic Surfaces
Clean the painted metal and plastic surfaces
weekly using a clean soft cloth, and mild cleaner.
Periodic applications of common furniture wax will
ease cleaning, and maintain the finished luster of
the surface. Use of chlorine based disinfectant can
cause damage to the hand control.
Calling for Service
If service is required, contact your Midmark dealer.
To contact Midmark directly:
1-800-Midmark (1-800-643-6275)
8:00 am until 5:00 pm Mon-Fri (EST)
Midmark Corporation
60 Vista Drive
Versailles, OH 45380-0286
Phone: 937-526-3662
Fax: 937-526-5542
midmark.com
Français : Référez-vous à
www.midmark.com
Release Lever
CAUTION
Headrest must be securely locked in place
before performing any exam or procedure.
To extend / retract the foot section..
A. Squeeze release lever on either side of foot section.
B. Pivot foot extension up / down until it locks into place.
To adjust the side rail (out / in)...
A. Loosen knob (C) for desired side rail.
B. Slide side rail out / in to desired position.
C. Tighten knob (C) to lock in place.
To adjust the pivot angle of the headrest...
A. Loosen knob (A).
B. Pivot headrest to desired position.
C. Tighten knob (A) to lock in place.
To adjust the height of the headrest...
A. Loosen knob (B).
B. Slide headrest out / in to desired position.
C. Tighten knob (B) to lock in place.
  • Page 1 1
  • Page 2 2

Midmark 641 Power Procedures Chair Guide de référence

Midmark
Marque
Midmark
Modèle
641 Power Procedures Chair
Taper
Guide de référence
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes