Ryobi C430 Manuel utilisateur

Marque: Ryobi

Modèle: C430

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

30cc 4-CYCLE

STRING TRIMMERS

TAILLE-BORDURES À LIGNE

4 TEMPS DE 30 cc

RECORTADORAS DE HILO

DE CUATRO TIMPOS 30 cc

RY4CCS

RY4CCSVNM

RY4CSS

RY4CSSVNM

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

TABLE OF CONTENTS

 General Safety Rules ...................... 2-3

 Specific Safety Rules ..........................3

 Symbols ..............................................4

 Features ..............................................5

 Assembly ........................................ 5-6

 Operation ........................................ 7-9

 Maintenance ................................. 9-13

 Troubleshooting .......................... 14-15

 Parts Ordering/Service ........ Back Page

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation

avant d’employer ce produit.

TABLE DES MATIÈRES

 Règles de sécurité générales .......... 2-3

 Règles de sécurité particulières .......... 3

 Symboles ............................................4

 Caractéristiques ..................................5

 Assemblage .................................... 5-6

 Utilisation ........................................ 7-9

 Entretien ...................................... 10-13

 Dépannage .................................. 14-15

 Commande de pièces /

réparation .......................... Páge arrière

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe

leer y comprender el manual del

operador antes de usar este producto.

ÍNDICE DE CONTENIDO

 Reglas de seguridad generales ...... 2-3

 Reglas de seguridad específicas ........3

 Símbolos .............................................4

 Características ....................................5

 Armado ........................................... 5-6

 Funcionamiento .............................. 7-9

 Mantenimiento ............................ 10-13

 Solución de problemas ............... 14-15

 Pedidos de piezas/

servicio ........................... Pág. posterior

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

A - String head (tête à ligne de coupe, cabezal

del hilo)

B - Drive shaft housing (tube de l’arbre moteur,

alojamiento del eje de impulsión)

C - Coupler (coupleur, acoplador)

D - Front handle (poignée avant, mango

delantero)

E - Strap hanger (dispositif d’accrochage,

colgador para la correa)

F - Stop switch (commutateur d’arrêt, interruptor

de apagado)

G - Trigger lock-out (gâchette avec verrou,

gatillo con seguro)

H - Starter grip and rope (poignée et cordon du

lanceur, mango y cuerda del arrancador)

I - Primer bulb (poire d’amorçage, bomba

de cebado)

J - Choke lever (levier de volet de départ,

palanca del anegador)

K - Fuel cap (bouchon de carburant, tapa del

tanque)

L - Rear handle (poignée arrière, mango

trasero)

- Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

N - Knob (bouton, perilla)

O - Curved shaft grass deflector (déflecteur

d’herbe d’arbre courbe, deflector de pasto

del eje curvo)

P - Straight shaft grass deflector (déflecteur

d’herbe d’arbre droit, deflector de pasto para

eje recto)

Q - Muffler (silencieux, silenciador)

R - SPEED WINDER

™

(SPEED WINDER

™

, SPEED

WINDER

™

)

Fig. 1

RY4CSS

RY4CSSVNM

RY4CCS

RY4CCSVNM

See this fold-out section for all of the figures referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner toutes les figures mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas las figuras a las que

se hace referencia en el manual del operador.

Fig. 2

A - Button (bouton, botón)

B - Guide recess (logement guide, hueco guía)

C - Coupler (coupleur, acoplador)

D - Power head shaft (arbre du bloc moteur, eje

del cabezal motor)

E - Knob (bouton, perilla)

F - Positioning hole (trou de positionnement,

orificio de posicionamiento)

G - Trimmer attachment (accessoire taille-

bordures, aditamento para recortar)

Fig. 3

A - Front handle

(poignée avant,

mango delantero)

B - Bolt (boulon, perno)

C - Wing nut (écrou

papillon, tuerca de

mariposa)

D - Handle support

(support de poignée,

soporte del mango)

E - Slot (fente, ranura)

F - Tab (ergot, orejeta)

iii

Fig. 10

Fig. 4

Fig. 7

A - Hex screw (vis à six pans, tornillo de

hexagonal)

B - Bracket (support, soporte)

C - Wing nut (écrou papillon, tuerca de

mariposa)

D - Curved shaft grass deflector (déflecteur

d’herbe d’arbre courbe, deflector de pasto

del eje curvo)

A - Stop switch (commutateur d’arrêt,

interruptor de apagado)

B - Trigger lock out (gâchette avec verrou,

gatillo con seguro)

C - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

D - Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

E - Primer bulb (poire d’amorçage, bomba

de cebado)

Fig. 5

A - Straight shaft grass deflector (déflecteur

d’herbe d’arbre droit, deflector de pasto para

eje recto)

B - Slot (fente, ranura)

C - Tab (languette, orejeta)

D - Bolt (boulon, perno)

Fig. 6

A - Oil cap/dipstick (bouchon/jauge d’huile, tapa

de relleno de aceite / varilla medidora de

aceite)

B - Hatched area (zone hachurée, área cubierta

con rayas entrecruzadas)

C - Oil fill hole (orifice de remplissage d’huile,

agujero de llenado de aceite)

D - Funnel cap (bouchon d’ entonnoir, tapa de

embudo)

FULL

CHOKE

RUN

HALF

CHOKE

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL UNTIL UNIT ATTEMPTS

TO START (MAX 4X)

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. PULL UNTIL UNIT STARTS

6. WAIT 10 SECONDS

7. SET TO

FULL CHOKE

HALF CHOKE

RUN

FULL

CHOKE

RUN

HALF

CHOKE

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL UNTIL UNIT ATTEMPTS

TO START (MAX 4X)

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. PULL UNTIL UNIT STARTS

6. WAIT 10 SECONDS

7. SET TO

FULL CHOKE

HALF CHOKE

RUN

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL STARTER ROPE UNTIL

THE ENGINE STARTS

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. WAIT 10 SECONDS

6. SET TO RUN

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL STARTER ROPE UNTIL

THE ENGINE STARTS

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. WAIT 10 SECONDS

6. SET TO RUN

FULL

CHOKE

RUN

HALF

CHOKE

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL UNTIL UNIT ATTEMPTS

TO START (MAX 4X)

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. PULL UNTIL UNIT STARTS

6. WAIT 10 SECONDS

7. SET TO

FULL CHOKE

HALF CHOKE

RUN

FULL

CHOKE

RUN

HALF

CHOKE

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL UNTIL UNIT ATTEMPTS

TO START (MAX 4X)

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. PULL UNTIL UNIT STARTS

6. WAIT 10 SECONDS

7. SET TO

FULL CHOKE

HALF CHOKE

RUN

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL STARTER ROPE UNTIL

THE ENGINE STARTS

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. WAIT 10 SECONDS

6. SET TO RUN

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL STARTER ROPE UNTIL

THE ENGINE STARTS

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. WAIT 10 SECONDS

6. SET TO RUN

FULL

CHOKE

RUN

HALF

CHOKE

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL UNTIL UNIT ATTEMPTS

TO START (MAX 4X)

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. PULL UNTIL UNIT STARTS

6. WAIT 10 SECONDS

7. SET TO

FULL CHOKE

HALF CHOKE

RUN

1. PRESS PRIMER BULB 10X

2. SET TO

3. PULL STARTER ROPE UNTIL

THE ENGINE STARTS

(DO NOT PULL THROTTLE TRIGGER)

4. SET TO

5. WAIT 10 SECONDS

6. SET TO RUN

Fig. 8

A - Full choke position (position de

complètement ouvert, posición de anegación

máxima)

B - Half choke position (position de demi ouvert,

posición de anegación media)

C - Run position (position de marche , posición

de marcha)

D - Choke lever (levier de volet de départ,

palanca del anegador)

A - Curved shaft trimmer (taille-bordures à

arbre courbe, recortadora de eje curvo)

B - Dangerous cutting area (zone de coupe

dangereuse, área peligrosa de corte)

C - Direction of rotation (sens de rotation,

sentido de rotación)

D - Best cutting area (zone d’efficacité

maximum, mejor área de corte)

Fig. 9

PROPER OPERATING POSITION

BONNE POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL MANEJO

DE LA HERRAMIENTA

Fig. 12

Fig. 11

A - Straight shaft trimmer (taille-bordures à

arbre droit, recortadora de eje recto)

B - Dangerous cutting area (zone de coupe

dangereuse, área peligrosa de corte)

C - Direction of rotation (sens de rotation,

sentido de rotación)

D - Best cutting area (zone d’efficacité

maximum, mejor área de corte)

Fig. 16

A - Eyelet (œillet, ojillo)

B - Arrows (flèches, flechas)

C - pull strings (tirer vers l’extérieur, tira del

hilo)

D - Rotate the bump knob (tourner le capuchon

du mécanisme de coup dans le sens horaire,

gire a la derecha el perilla percusiva)

Fig. 15

Fig. 13

A - String head housing (boîtier de tête de

coupe, alojamiento del cabezal de hilo)

B - Depress tabs (appuyer sur les languettes,

presione los orejetas)

A - Upper string head housing (boîtier

supérieure de tête de coupe, alojamiento

superior del cabezal de hilo)

B - Tabs (languettes, lengüetas)

C - Lower string head housing (boîtier inférieur

de tête de coupe, alojamiento del cabezal de

hilo)

D - Spool (bobine, carrete)

E - Bump knob (capuchon du mécanisme de

coup, perilla percusiva)

F - Spool slots (fentes de bobine, ranuras de

carrete)

G - Knob ribs (côte de bouton, costillas de la

perilla)

Fig. 14

A - SPEED WINDER

™

(SPEED WINDER

™

, SPEED

WINDER

™

)

B - Bump knob (capuchon du mécanisme de

coup, perilla percusiva)

A - Straight shaft trimmer cut-off blade (lame

de sectionnement de ligne du taille-bordures

à arbre droit, cuchilla de corte de hilo de la

recortadora de eje recto)

B - Curved shaft trimmer cut-off blade (lame de

sectionnement de ligne du taille-bordures à

arbre courbe, cuchilla de corte de hilo de la

recortadora de eje recto)

A - Idle speed screw (vis de ralenti, tornillo de

ajuste de la velocidad en vacío)

Fig. 17

A - Starter grip and rope (poignée et cordon du

lanceur, mango y cuerda del arrancador)

B - Deep hole in camshaft gear (trou profond

situé dans l’engrenage de l’arbre à cames,

orificio profundo en el engranaje del árbol de

levas)

Fig. 22

A - Feeler gauge (jauge d’épaisseur, calibrador

de separaciones)

B - Rocker arm (culbuteur, balancín)

C - Rocker arm cover (cache -culasse, tapa del

balancín)

D - Torx screw (vis à Torx, tornillo de torx)

Fig. 23

A - Retaining nut (écrou de retenue, tuerca de

retencion)

B - Adjusting nut (écrou de réglage, tuerca de

ajuste)

C - Stud (goujon, elemento estructural)

Fig. 21

A - Screw (vis, tornillo)

B - Top engine cover (couvercle moteur

supérieur, cubierta superior del motor)

C - Bottom cover (couvercle inférieure, cubierta

inferior)

Fig. 20

A - Air filter (filtre à air, filtro de aire)

Fig. 19

A - Latch (loquet, pestillo)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

C - Tabs (languettes, orejetas)

D - Slots (fentes, ranuras)

Fig. 18

2 — English

GENERAL SAFETY RULES

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below may result in

electric shock, fire and/or serious personal injury.

READ ALL INSTRUCTIONS

 For safe operation, read and understand all instructions

before using this product. Follow all safety instructions.

Failure to follow all safety instructions listed below, can

result in serious personal injury.

 Do not allow children or untrained individuals to use this

unit.

 Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

 Clear the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or loose string

which can be thrown or become entangled in the cutting

line or blade.

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment. Failure to do so could

result in objects being thrown into your eyes and other

possible serious injuries.

 Wear heavy, long pants, long sleeves, boots, and gloves.

Do not wear loose fitting clothing, short pants, sandals,

or go barefoot. Do not wear jewelry of any kind.

 Heavy protective clothing may increase operator fatigue,

which could lead to heat stroke. During weather that is

hot and humid, heavy work should be scheduled for early

morning or late afternoon hours when temperatures are

cooler.

 Never operate this unit on the operator’s left side.

 Secure long hair above shoulder level to prevent

entanglement in moving parts.

 Keep all bystanders, children, and pets at least

50 ft. away. Bystanders should be encouraged to wear

eye protection. If you are approached, stop the engine

and cutting attachment. In the case of bladed units, there

is the added risk of injury to bystanders from being struck

with the moving blade in the event of a blade thrust or

other unexpected reaction of the saw.

 Do not operate this unit when you are tired, ill, upset, or

under the influence of alcohol, drugs, or medication.

 Do not operate in poor lighting.

 Keep firm footing and balance. Do not overreach.

Overreaching can result in loss of balance or exposure

to hot surfaces.

  Do not use on a ladder, rooftop, tree, or other unstable

support. Stable footing on a solid surface enables better

control of the unit in unexpected situations.

 Keep all parts of your body away from any moving part.

 To avoid hot surfaces, never operate the unit with the

bottom of the engine above waist level.

 Do not touch area around the muffler or cylinder of the

unit, these parts get hot from operation. Contact with hot

surfaces could result in possible serious personal injury.

 Always stop the engine and remove the spark plug wire

before making any adjustments or repairs except for

carburetor adjustments.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace any damaged parts before use.

 Never use blades, flailing devices, wire, or rope on trim-

mer attachment. Never use flailing devices, wire, or rope

on any attachment.

 The cutting attachment should never rotate at idle during

normal use. The cutting attachment may rotate at idle

during carburetor adjustments.

 It has been reported that vibrations from hand-held tools

may contribute to a condition called Raynaud’s Syndrome

in certain individuals. Symptoms may include tingling,

numbness, and blanching of the fingers, usually apparent

upon exposure to cold. Hereditary factors, exposure to

cold and dampness, diet, smoking, and work practices

are all thought to contribute to the development of these

symptoms. It is presently unknown what, if any, vibrations

or extent of exposure may contribute to the condition.

There are measures that can be taken by the operator to

possibly reduce the effects of vibration:

a) Keep your body warm in cold weather. When operating

the unit wear gloves to keep hands and wrists warm.

It is reported that cold weather is a major factor

contributing to Raynaud’s Syndrome.

b) After each period of operation, exercise to increase

blood circulation.

c) Take frequent work breaks. Limit the amount of

exposure per day.

d) Keep the tool well maintained, fasteners tightened,

and worn parts replaced.

If you experience any of the symptoms of this condition,

immediately discontinue use and see your physician about

these symptoms.

 Store fuel in a container approved for gasoline.

 Wipe up any fuel spillage. Move 30 ft. away from refueling

site before starting engine. Slowly remove the fuel cap

after stopping engine. Do not smoke when refueling.

 Stop the engine and allow to cool before refueling or

storing the unit.

3 — English

SPECIFIC SAFETY RULES

 Inspect before use. Replace damaged parts. Make sure

fasteners are in place and secure. Check for fuel leaks.

 Replace string head if cracked, chipped, or damaged

in any way. Be sure the string head or blade is properly

installed and securely fastened. Failure to do so can cause

serious injury.

 Make sure all guards, straps, deflectors, and handles are

properly and securely attached.

 Use only recommended or equivalent replacement line in

the cutting head. Do not use any other cutting attachment.

To install any other type of replacement line or cutting

head to this string trimmer can result in serious personal

injury. Never use, for example, wire or wire-rope, which

can break off and become a dangerous projectile.

 Never operate unit without the grass deflector in place

and in good condition.

 Maintain a firm grip on both handles while trimming. Keep

string head below waist level. Never cut with the string

head located over 30 in. or more above the ground.

 This product is intended for infrequent use by homeowners

and other occasional users for such general applications

as trimming light and heavy vegetation, etc. It is not

intended for prolonged use. Prolonged periods of

operation can cause circulatory problems in the

user’s hands due to vibration. For such use, it may be

appropriate to use a product having an anti-vibration

feature.

 Save these instructions. Refer to them frequently and use

them to instruct others who may use this tool. If you loan

someone this tool, loan them these instructions also.

GENERAL SAFETY RULES

 Allow the engine to cool; empty the fuel tank, and secure

the unit from moving before transporting in a vehicle.

 Wear your protective equipment and observe all safety

instructions. For units equipped with a clutch, be sure

the cutting attachment stops turning when the engine

idles. When the unit is turned off make sure the cutting

attachment has stopped before the unit is set down.

 We recommend taking your equipment to a qualified

service center for repair, as service performed by

inexperienced or unqualified persons may damage the

equipment, create unsafe conditions, injury to user and/

or void your warranty.

4 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment.

Wear Gloves

Wear non-slip, heavy-duty protective gloves when

handling this equipment.

Wear Safety Footwear

Wear non-slip safety footwear when using this

equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury

or property damage.

No Blade

Do not install or use any type of blade on a product

displaying this symbol.

Hot Surface

To reduce the risk of injury or damage, avoid contact with

any hot surface.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

5 — English

PRODUCT SPECIFICATIONS

Line Cutting Width

Curved Shaft .........................................................17 in.

Straight Shaft ........................................................18 in.

Engine Displacement....................................................30cc

Engine Lubricant Volume............................................2.2 oz

Line Diameter .........................................................0.095 in.

FEATURES

KNOW YOUR STRING TRIMMER

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

ERGONOMIC DESIGN

The design of the trimmer provides for easy handling. It is

designed for comfort and ease of grasp when operating in

different positions and at different angles.

GRASS DEFLECTOR

The trimmer includes a grass deflector that helps protect

you from flying debris.

OIL CAP/DIPSTICK

Remove the oil fill cap to check and add lubricant when

necessary.

TOP-MOUNTED ENGINE

The top-mounted engine improves balance and is located

away from the dust and debris of the cutting area.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the packing list are

already assembled to your product when you unpack it.

Parts on this list are not assembled to the product by the

manufacturer and require customer installation. Use of a

product that may have been improperly assembled could

result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Curved Shaft

Trimmer Assembly

Front Handle with Hardware

Curved Shaft Grass Deflector

Bottle of 4-Cycle Lubricant

Funnel Cap

SPEED WINDER

™

Operator’s Manual

Straight Shaft

Trimmer Assembly

Front Handle with Hardware

Straight Shaft Grass Deflector

Bottle of 4-Cycle Lubricant

Funnel Cap

SPEED WINDER

™

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this product.

Any such alteration or modification is misuse and could

result in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

6 — English

ASSEMBLY

INSTALLING THE POWER HEAD TO THE

ATTACHMENT

See Figure 2.

WARNING:

Never install, remove, or adjust any attachment while

power head is running. Failure to stop the engine can

cause serious personal injury.

The attachment connects to the power head by means of

a coupler device.

 Stop the engine and disconnect the spark plug wire.

 Loosen the knob on the coupler of the power head shaft.

 Push in the button located on the attachment shaft. Align

the button with the guide recess on the power head coupler

and slide the two shafts together. Rotate the attachment

shaft until the button locks into the positioning hole.

NOTE: If the button does not release completely in the

positioning hole, the shafts are not locked into place.

Slightly rotate from side to side until the button is locked

into place.

 Tighten the knob securely.

WARNING:

Be certain the knob is fully tightened before operating

equipment; check it periodically for tightness during use

to avoid serious personal injury.

REMOVING THE ATTACHMENT FROM THE

POWER HEAD

 Stop the engine and disconnect the spark plug wire.

 Loosen the knob.

 Push in the button and twist the shafts to remove and

separate ends.

ATTACHING THE FRONT HANDLE

See Figure 3.

 Press the front handle onto the top of the upper shaft, in

the position indicated by the arrow on the shaft, angling

the handle toward the throttle trigger.

 Place the front handle along the upper shaft to a position

that allows for comfortable operation.

 Insert the handle support tab into the slot in the front

handle.

 Align the hole in the front handle with the hole in the

handle support.

 Insert bolt through holes in front handle and handle

support. Secure handle in place using wing nut.

NOTE: Do not cover any portion of the warning label with

the front handle.

ATTACHING THE GRASS DEFLECTOR

WARNING:

The line cut-off blade on the grass deflector is sharp.

Avoid contact with the blade. Failure to avoid contact

can result in serious personal injury.

TO ATTACH THE CURVED SHAFT GRASS

DEFLECTOR

See Figure 4.

 Remove hex screw and wing nut from grass deflector.

 Press the grass deflector onto the bottom of the curved

shaft as shown.

 Insert the hex screw through the grass deflector and the

bracket on the curved shaft.

 Place the wing nut on the hex screw and tighten securely.

TO ATTACH THE STRAIGHT SHAFT GRASS

DEFLECTOR

See Figure 5.

 Remove the bolt from the grass deflector.

 Insert the tab on the mounting bracket in the slot on the

grass deflector.

 Align the screw hole in the mounting bracket with the

screw hole in the grass deflector.

 Insert the bolt through the mounting bracket and into the

grass deflector.

 Tighten the bolt securely using a flat blade screwdriver

or 5/16 in. wrench.

7 — English

OPERATION

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Never use blades, flailing devices, wire, or rope on this

product. Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

NOTICE:

The spark arrestor on this product has not been evaluated

by the USDA Forest Service and cannot be used on U.S.

forest lands. In addition, product users must comply

with Federal, State, and local fire prevention regulations.

Check with appropriate authorities. Contact customer

service or a qualified service center to purchase a

replacement spark arrestor.

NOTICE:

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts,

caps, etc. Tighten securely all fasteners and caps and

do not operate this product until all missing or damaged

parts are replaced. Please contact customer service or

a qualified service center for assistance.

ETHANOL-BLENDED FUELS

NOTICE:

Do not use E15 or E85 fuel in this product. It is a

violation of federal law and will damage the unit

and void your warranty. Only use unleaded gasoline

containing up to 10% ethanol.

FUELING AND REFUELING THE TRIMMER

WARNING:

Gasoline and its vapors are highly flammable and

explosive. To prevent serious personal injury and property

damage, handle it with care. Keep away from ignition

sources and open flames, handle outdoors only, do not

smoke and wipe up spills immediately.

 Clean surface around fuel cap to prevent contamination.

 Loosen fuel cap slowly by turning counterclockwise. Rest

the cap on a clean surface.

 Carefully pour fuel into the tank. Avoid spillage.

 Prior to replacing the fuel cap, clean and inspect the

gasket.

 Immediately replace fuel cap and hand tighten by turning

it clockwise. Wipe up any fuel spillage.

NOTE: It is normal for smoke to be emitted from a new

engine after first use.

WARNING:

Check for fuel leaks, which are a fire hazard. Failure

to do so could result in a fire that could cause serious

personal injury.

WARNING:

Always shut off engine before fueling. Never remove

fuel cap or add fuel to a machine with a running or hot

engine. Make sure the unit is sitting on a flat, level surface

and only add fuel outdoors. If the engine is hot, let the

unit cool for at least five minutes before adding fuel.

After fueling, immediately replace fuel cap and tighten

securely. Move at least 30 ft. from refueling site before

starting engine. Do not smoke and stay away from open

flames and sparks! Failure to follow these instructions

could result in a fire and cause serious personal injury.

ADDING/CHECKING ENGINE LUBRICANT

See Figure 6.

NOTICE:

Attempting to start the engine before it has been properly

filled with lubricant will result in equipment failure.

Engine lubricant has a major influence on engine performance

and service life. This unit is shipped with a 20W50 engine

lubricant to assist in the break-in period. For best operating

performance, continuing to use 20W50 engine lubricant is

recommended, however, SAE 30, 10W30, or 10W40 are

all acceptable lubricants to use in this product. Always

use a 4-stroke engine lubricant that meets or exceeds

the requirements for API service classification SJ. Check

lubricant level before each use.

8 — English

OPERATION

NOTE: Non-detergent or 2-stroke engine lubricants will

damage the engine and should not be used.

To add engine lubricant:

 Remove the cap and seal from lubricant bottle provided.

 Screw the funnel cap onto lubricant bottle.

 Unscrew the oil cap/dipstick and remove.

 Add entire bottle of engine lubricant through oil fill hole.

 Reinstall the oil cap/dipstick and secure.

 Remove the funnel cap from lubricant bottle. Clean and

store for later use.

To check engine lubricant level:

 Separate the attachment from the power head.

 Set power head on a flat level surface with shaft parallel

to surface.

 Unscrew the oil cap/dipstick and remove.

 Wipe dipstick clean; re-seat in hole and rethread.

 Remove dipstick again and check lubricant level. Lubricant

level should fall within the hatched area on the dipstick.

 If level is low, add engine lubricant until the fluid level rises

to the upper portion of the hatched area on the dipstick.

 Replace and secure the oil cap/dipstick.

NOTICE:

Do not overfill. Overfilling the crankcase may cause

excessive smoke, lubricant loss, and engine damage.

STARTING AND STOPPING

See Figures 7 - 8.

Trimmer should be on a flat, bare surface for starting.

To start a cold engine:

Slowly press the primer bulb 10 times.

NOTE: After the 7th press, fuel should be visible in the

primer bulb. If it is not, continue to press the primer until

you see fuel in the bulb.

Set the choke lever to FULL CHOKE position.

NOTE: Squeeze throttle trigger fully through remaining steps.

With throttle trigger fully engaged, pull the starter grip

and rope until the engine runs (a maximum of 3 times).

NOTE: If engine has not started after 3 pulls:

 If the outside temperature is 60°F or below, leave the

choke in the FULL CHOKE position and continue to

pull the starter grip and rope until the engine runs.

 If the outside temperature is 60°F or above, set the

choke lever to the HALF CHOKE position and pull the

starter grip and rope until the engine runs.

After 10 seconds, set choke lever to RUN.

To restart a warm engine:

Slowly press the primer bulb 10 times.

Set the choke lever to the RUN position.

Pull the starter grip and rope until the engine runs.

To stop the engine:

To stop the engine, depress the STOP switch to the stop

position “ ”.

IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:

Do not return this product to the retail store where it was

purchased. Please call our Customer Service Department

for any issues you may have.

For Help Call: 1-800-860-4050

OPERATING THE TRIMMER

See Figure 9.

WARNING:

Engine housing can become hot during trimmer operation.

Do not rest or place your arm, hand, or any body part

against the engine housing during trimmer operation.

Only hold the trimmer as shown in figure 9 with all body

parts clear of engine housing. Extended contact with

the engine housing can result in burns or other injuries.

WARNING:

Always position the unit on the operator’s right side. The

use of the unit on the operator’s left side will expose the

user to hot surfaces and can result in possible burn injury.

WARNING:

To avoid burns from hot surfaces, never operate unit with

the bottom of the engine above waist level.

Hold the trimmer with your right hand on the rear handle

and your left hand on the front handle. Keep a firm grip with

both hands while in operation. Trimmer should be held at a

comfortable position with the rear handle about hip height.

Cut tall grass from the top down. This will prevent grass from

wrapping around the shaft housing and string head which

could cause damage from overheating. If grass becomes

wrapped around the string head, STOP THE ENGINE,

disconnect the spark plug wire, and remove the grass.

WARNING:

Always hold the string trimmer away from the body

keeping clearance between the body and the product.

Any contact with the housing or string trimmer cutting

head can result in burns and/or other serious personal

injury.

9 — English

OPERATION

CUTTING TIPS

See Figures 9 - 11.

 Avoid hot surfaces by always keeping the tool away from

your body. (Proper operating position shown in figure 9.)

 Keep the trimmer tilted toward the area being cut; this is

the best cutting area.

 The curved shaft trimmer cuts when passing the unit from

right to left. The straight shaft trimmer cuts when passing

the unit from left to right. This will avoid throwing debris at

the operator. Avoid cutting in the dangerous area shown

in illustration.

 Use the tip of line to do the cutting; do not force string

head into uncut grass.

 Wire and picket fences cause extra line wear, even

breakage. Stone and brick walls, curbs, and wood may

wear line rapidly.

 Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by the line.

TO ADVANCE THE CUTTING LINE

Line advance is controlled by tapping the string head on

grass while running engine at full throttle.

 Run engine at full throttle.

 Tap the bump knob on ground to advance line. The line

advances each time the knob is tapped. Do not hold the

knob on the ground.

NOTE: The line trimming cut-off blade on the grass deflector

will cut the line to the correct length.

NOTE: If the line is worn too short you may not be able to

advance the line by tapping it on the ground. If so, stop the

engine and manually advance the line.

To advance the cutting line manually:

Stop the engine and disconnect the spark plug wire.

 Push the bump knob down while pulling on line(s) to

manually advance the line.

GRASS DEFLECTOR LINE TRIMMING CUT-OFF

BLADE

See Figure 12.

The trimmer is equipped with a line trimming cut-off blade

on the grass deflector. For best cutting, advance line until it

is trimmed to length by the cut-off blade. Advance the line

whenever you hear the engine running faster than normal,

or when trimming efficiency diminishes. This will maintain

best performance and keep the line long enough to advance

properly.

MAINTENANCE

Normal maintenance, replacement or repair of emission

control devices and systems may be performed by any

qualified repair establishment or individual with original

or equivalent parts. Warranty and recall repairs must be

performed by a authorized service center; please contact

customer service for assistance.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Failure to follow these instructions can result in

serious personal injury or property damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

When servicing, use only recommended or equivalent

replacement parts. Use of any other parts could create

a hazard or cause product damage.

NOTICE:

The spark arrestor on this product has not been evaluated

by the USDA Forest Service and cannot be used on U.S.

forest lands. In addition, product users must comply

with Federal, State, and local fire prevention regulations.

Check with appropriate authorities. Contact customer

service or a qualified service center to purchase a

replacement spark arrestor.

NOTICE:

Periodically inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts,

caps, etc. Tighten securely all fasteners and caps and

do not operate this product until all missing or damaged

parts are replaced. Please contact customer service or

a qualified service center for assistance.

10 — English

MAINTENANCE

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, lubricant, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-based

products, penetrating lubricants, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which can result in serious personal injury.

LINE REPLACEMENT

See Figures 13 - 14.

Use only .095 in. trimmer line. Use original manufacturer’s

replacement line for best performance.

 Stop the engine and disconnect the spark plug wire.

 Rotate the bump knob clockwise as necessary to align the

arrows on the bump knob with the arrows on the string

head housing.

 Cut one piece of trimmer line 16 ft. long. Insert the line

into the eyelet on the string head housing. Push until the

end of the line comes out the other side of the housing.

Pull the line until equal amounts of line appear on both

sides of the housing.

NOTE: Line may jam if more than 16 ft. is loaded.

 Either by hand or using the Speed Winder

™

, rotate the

bump knob clockwise to wind the line on the spool until

approximately 6 in. of line is showing on each side.

NOTE: For best results, after every five to seven revolutions

of the Speed Winder

™

, pull both line ends taut for best

loading results and to help prevent line from tangling.

 Push the bump knob down while pulling on line(s) to

manually advance the line.

CLEARING LINE JAM AND/OR REPLACING

BUMP KNOB

See Figures 15 - 16.

 Stop the engine and disconnect the spark plug wire.

 Depress the tabs on the side of the string head housing

to remove the lower string head housing.

NOTE: The housing is spring loaded and will self eject

when the tabs are depressed. It is not necessary to remove

the upper string head housing from the drive shaft.

 Push the spool and bump knob through the string head

housing and remove the string from the spool.

 If replacing the bump knob, remove the old knob from

the spool. Align the knob ribs with the spool slots and

place the new bump knob onto the spool. If you are not

replacing the bump knob, skip this step.

 Insert the bump knob and spool assembly through the

opening in the string head housing.

 Align the slots on the lower string head housing with the

tabs on the upper string head housing.

 Push the housing together until the tabs snap into place.

NOTE: Hold the spool by the knob while completing the

installation.

 Install line as described in Line Replacement.

IDLE SPEED ADJUSTMENT

See Figure 17.

WARNING:

The cutting head will move when adjusting the idle speed.

Wear all protective clothing and keep all bystanders,

children, and pets at least 50 ft. away. Make adjustments

with the unit supported by hand so that the cutting head

does not contact the ground or any object. Keep all parts

of your body away from the cutting head and muffler.

Failure to follow these instructions could result in serious

personal injury.

If the cutting attachment turns at idle, the idle speed screw

needs adjusting on the engine. Turn the idle speed screw

counterclockwise to reduce the idle RPM and stop the

cutting attachment movement. If the cutting attachment still

moves at idle speed, contact a service dealer for adjustment

and discontinue use until the repair is made.

WARNING:

The cutting attachment should never turn at idle. Turn

the idle speed screw counterclockwise to reduce the

idle RPM and stop the cutting attachment, or contact a

service dealer for adjustment and discontinue use until

the repair is made. Serious personal injury could result

from the cutting attachment turning at idle.

CLEANING THE AIR FILTER

See Figures 18 - 19.

For proper performance and long life, keep air filter screen

clean.

 Remove the air filter cover. To remove, push up on the

latch at the bottom of the cover and gently pull the cover

up.

 Remove the air filter.

 Clean the foam filter element with warm soapy water.

Rinse and let dry.

NOTE: If the foam filter element is damaged, it should be

replaced.

 Apply a light coat of engine lubricant to the foam filter

element, then squeeze it out.

11 — English

MAINTENANCE

 Tip power head on its side and allow lubricant to drain

from the oil fill hole into an approved container.

NOTE: Drain the lubricant while the engine is still warm

but not hot. Warm lubricant will drain quickly and more

completely.

 Return the power head to an upright position and refill

with lubricant following the instructions in the Adding/

Checking Engine Lubricant section previously in this

manual.

NOTICE:

Do not overfill. Overfilling the crankcase may cause

excessive smoke, lubricant loss, and engine damage.

 Reinstall the bottom engine cover. Replace the screws

and tighten securely.

 Replace the screw in the top engine cover and tighten

securely.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local retailer for more information.

ADJUSTING CAMSHAFT-TO-ROCKER ARM

CLEARANCE

See Figures 21 - 23.

Inspect the camshaft-to-rocker arm clearance after every

25 hours of operation. This should be done in a clean, dust-

free environment.

NOTE: This procedure requires partial disassembly of the

engine. If you are unsure if you are qualified to perform this

operation, take the unit to a qualified service center.

 Stop the engine and disconnect the spark plug wire. Allow

the engine to cool completely before proceeding.

 Remove the screw from the top engine cover. Remove

engine cover and set aside.

 Using a Torx screwdriver, remove the screw from the

rocker arm cover. Remove the cover and set aside.

 Position camshaft by pulling the starter grip and rope just

until the deep hole in the camshaft gear is located at the

6 o’clock position as shown.

 Place the feeler gauge under each rocker arm and measure

the gap. The gap should be between .004 in. (0.10 mm)

and .006 in. (0.15 mm) for both rocker arms.

NOTE: Use a standard automotive feeler gauge. The

.004 in. (0.10 mm) feeler gauge should slide between

the rocker arm and valve stem with a slight amount of

resistance but without binding. The 0.006 in. (0.15 mm)

feeler gage should not slide between the rocker arms and

the cam lobes — it should be held tight.

 If the valve clearance is not between .004 in. (0.10 mm)

and .006 in. (0.15 mm), the clearance should be adjusted

as follows:

 Reinstall the air filter.

NOTE: Make sure the filter is seated properly inside the

cover. Installing the filter incorrectly will allow dirt to enter

the engine, causing rapid engine wear.

 Replace the air filter cover by placing the slots on the air

filter cover over the tabs on the housing, then push the

cover down until it latches securely in place.

FUEL CAP, TANK, AND LINES

WARNING:

Check for fuel leaks. A leaking fuel cap, tank, or line is a

fire hazard and must be replaced immediately. If you find

any leaks, correct the problem before using the product.

Failure to do so could result in a fire that could cause

serious personal injury.

The fuel cap contains a non-serviceable filter and a

check valve. A clogged fuel filter will cause poor engine

performance. If performance improves when the fuel cap

is loosened, check valve may be faulty or filter clogged.

Replace fuel cap if required.

SPARK PLUG REPLACEMENT

This engine uses an Champion RY4C, Ryobi AC00164A,

or equivalent spark plug with .025 in. electrode gap. Use

a recommended or equivalent replacement and replace

annually.

NOTICE:

Be careful not to cross-thread the spark plug. Cross-

threading will seriously damage the product.

CHANGING ENGINE LUBRICANT

See Figure 20.

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious

burns.

For best performance, engine lubricant should be changed

after every 25 hours of operation.

To change the engine lubricant:

 Stop the engine and disconnect the spark plug wire. Allow

the engine to cool completely before proceeding.

 Remove the screw from the top engine cover and set

aside.

 Remove the screws from the bottom engine cover. Remove

the bottom cover and set aside.

 Remove the oil fill cap/dipstick.

12 — English

MAINTENANCE

 • While holding a wrench on the flats of the adjusting nut

with one hand, loosen the retaining nut with a second

wrench as shown. Take care not to loosen the stud.

 • Rotate the adjusting nut until it touches the feeler gauge.

Once the gap setting is correct, hold the wrench on

the flats of the adjusting nut and retighten the retaining

nut securely.

 Adjust the second rocker arm, if necessary.

 Replace the rocker arm cover and screw; tighten securely.

 Replace the top engine cover and screw; tighten securely.

WARNING:

Ensure all engine cover and all engine parts are

completely and properly reassembled before starting

engine. Failure to correctly reassemble engine could

result in serious injury or property damage.

STORING THE PRODUCT

We recommend that the unit be kept in a horizontal position

when stored.

 Clean all foreign material from the product. Store idle unit

indoors in a dry, well-ventilated area that is inaccessible

to children. Keep away from corrosive agents such as

garden chemicals and de-icing salts.

 If storing the product vertically, do so with the engine up

to avoid hydraulically locking the engine due to lubricant

entering the combustion chamber.

NOTE: If the engine/starter rope becomes locked after

storage, place the unit flat on the ground in the upright

position to allow the engine lubricant to slowly migrate

back into the engine’s oil reservoir.

 Abide by all ISO and local regulations for the safe storage

and handling of gasoline.

When storing 1 month or longer:

 Drain all fuel from tank into a container approved for

gasoline. Run engine until it stops.

HIGH ALTITUDE ENGINE OPERATION

Your engine is configured for operation below 2000 feet

altitude at the factory. Your engine must be reconfigured for

operation above 2000 feet altitude. Operating the engine

with the wrong engine configuration at a given altitude may

increase its emissions, decrease fuel efficiency, degrade per-

formance and cause irreversible damage. Engines configured

for high altitude operation cannot be operated in standard

altitude conditions. A qualified service center should ensure

that your engine is properly configured for your location.

13 — English

MAINTENANCE

MAINTENANCE SCHEDULE

Inspect For Clean Replace Replace

Maintenance Damage Before Every Every 25 Hours Every

Part Each Use 5 Hours or Yearly 50 Hours

* AIR FILTER ASSY

includes:

Filter .................................................................................... X

* CARBURETOR ASSY

* FUEL TANK ASSY

includes:

Fuel Lines ..................................... X

Fuel Cap ....................................... X

Fuel Filter................................................................................................................... X

* IGNITION ASSY

includes:

Spark Plug ................................................................................................................. X

* NOTICE: THE USE OF EMISSION CONTROL COMPONENTS OTHER THAN THOSE DESIGNED FOR THIS UNIT

IS A VIOLATION OF FEDERAL LAW.

CALL US FIRST

For any questions about operating or maintaining your product,

call the Ryobi Help Line!

Your product has been fully tested prior to shipment to ensure

your complete satisfaction.

14 — English

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Engine will not start No spark.

No fuel.

Engine is flooded.

Clean or replace spark plug. Reset spark plug gap.

Refer to Spark Plug Replacement earlier in this

manual.

Push primer bulb until bulb is full of fuel. If bulb

does not fill, primary fuel delivery system is blocked.

Contact a qualified service center. If primer bulb fills,

engine may be flooded, proceed to next item.

Set the choke lever to the RUN position. Squeeze the

trigger and pull the rope repeatedly until the engine

starts and runs.

NOTE: Depending on the severity of the flooding,

this may require numerous pulls of the starter grip

and rope.

Engine does not reach full

speed and emits excessive

smoke

Air filter is dirty.

Spark arrestor screen is dirty.

Spark plug fouled.

Clean air filter. Refer to Cleaning the Air Filter earlier

in this manual.

Contact a qualified service center.

Clean or replace spark plug. Reset spark plug gap.

Refer to Spark Plug Replacement earlier in this

manual.

Engine starts, runs, and

accelerates but will not idle

Idle speed screw on carburetor

needs adjustment.

Turn idle speed screw clockwise to increase idle

speed. See Figure 17.

Engine emits too much smoke Too much lubricant in crankcase. Drain lubricant and refill with correct amount of 20W50

engine lubricant. See Adding/Checking Engine

Lubricant in the Operation section of this manual.

Engine rope cannot be pulled Lubricant has entered the

combustion chamber.

This is usually caused by storing the unit for an

extended time with the engine in an upside-down

position. Remove and clean the spark plug. Drain the

lubricant out of the spark plug hole, then reinstall the

spark plug.

Check engine lubricant and add if necessary prior

to starting. Refer to Adding/Checking Engine

Lubricant earlier in this manual.

Line will not advance Line is welded to itself.

Not enough line on spool.

Line is worn too short.

Line is tangled on spool.

Engine speed is too slow.

Replace line. Refer to the applicable line replacement

section in this manual.

Install more line. Refer to the applicable line

replacement section in this manual.

Pull lines while alternately pressing down on and

releasing the bump knob.

Remove line from spool and rewind. Refer to the

applicable line replacement section in this manual.

Advance line at full throttle.

15 — English

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Grass wraps around driveshaft

housing and string head

Cutting tall grass at ground level.

Operating trimmer at part throttle.

Cut tall grass from the top down to prevent wrapping.

Operate trimmer at full throttle.

If problem persists after trying the above solutions, contact customer service or a qualified service center for assistance.

NOTICE:

As the equipment owner, you are responsible for the performance of the required maintenance listed in the Maintenance

section. It is recommended that you retain all receipts covering maintenance on your equipment. Neglecting or failing

to perform the required maintenance may increase emissions, decrease fuel efficiency, degrade performance, cause

irreversible engine damage and/or void your warranty.

This product has a Three-year Limited Warranty for personal,

family, or household use (30 days for business or commercial use).

For warranty details, visit www.ryobitools.com

or call (toll free) 1-800-860-4050.

2 — Français

RÈGLES DE SÉCURITÉ GÉNÉRALES

AVERTISSEMENT :

LIRE ET VEILLER À BIEN COMPRENDRE TOUTES

LES INSTRUCTIONS. Le non respect des instructions

ci-dessous peut entraîner un choc électrique, un incendie

et / ou des blessures graves.

LIRE TOUTES LES INSTRUCTIONS

 Pour travailler en toute sécurité, lire et veiller à bien

comprendre toutes les instructions avant d’utiliser ce

produit. Respecter toutes les instructions de sécurité. Le

non respect des instructions de sécurité ci-dessous peut

entraîner des blessures graves.

 Ne pas laisser des enfants ou personnes n’ayant pas reçu

une formation adéquate utiliser cet outil.

 Ne pas démarrer ou faire tourner le moteur dans un espace

confine, de bâtiment, à proximité des fenêtres ouverts, autre

ou des zones sans ventilation où des vapeurs toxiques de

monoxyde de carbone peuvent s’accumuler. Le monoxyde

de carbone, un gaz incolore, inodore et extrêmement

toxique peut causer une perte de conscience et être mortel.

 Déblayer la zone de travail avant chaque utilisation. La

débarrasser de tous les objets tels que cailloux, verre brisé,

clous, fils métalliques, cordes, etc. risquant d’être projetés

ou de se prendre dans la ligne de coupe ou la lame.

 Toujours porter une protection oculaire avec écrans latéraux

certifiée conforme à la norme ANSI Z87.1 ainsi qu’un

protection auditive lors de l’utilisation de ce produit.Si

cette précaution n’est pas prise, des objets peuvent être

projetés dans les yeux et causer des lésions graves.

 Porter des pantalons longs, manches longues, des

chaussures de travail et des gants épais. Ne pas porter

de vêtements amples, bijoux, shorts, sandales et ne pas

travailler pieds nus. Ne porter aucun bijou.

 Le fait de porter des vêtements de protection lourds peut

augmenter la fatigue de l’utilisateur, ce qui pourrait entraîner

un coup de chaleur. Si le temps est chaud et humide,

effectuer les gros travaux le matin ou en fin d’après-midi,

alors qu’il fait plus frais.

 Ne jamais utiliser cet outil en le tenant du côté gauche.

 Attacher les cheveux longs pour les maintenir au-dessus

des épaules, afin qu’ils ne se prennent pas dans les pièces

en mouvement.

 Garder les badauds, enfants et visiteurs à une distance de 15

m (50 pi). Recommander aux personnes présente de porter

une protection oculaire. Si quelqu’un s’approche pendant

l’utilisation de l’outil, arrêter le moteur et l’accessoire de

coupe. Le risque de blessure est accru si on utilise un outil

à lames. En effet, les personnes se trouvant à proximité

risquent d’être heurtés par une lame en marche advenant

qu’elle ricoche, ou à la suite de toute autre réaction

inattendue de la scie.

 Ne pas utiliser cet outil en état de fatigue, si l’on est souffrant

ou contrarié, ou sous l’influence de l’alcool, de drogues

ou de médicaments.

 Ne pas travailler sous un éclairage insuffisant.

 Se tenir bien campé et en équilibre. Ne pas travailler hors

de portée. Le travail hors de portée risque de faire perdre

l’équilibre ou de causer un contact avec les pièces brûlantes.

 Ne pas utiliser sur une échelle, un toit, dans un arbre ou

sur toute surface instable. Une bonne tenue et un bon

équilibre permettent de mieux contrôler l’outil en cas de

situation imprévue.

 Garder toutes les parties du corps à l’écart des pièces en

mouvement.

 Pour éviter le contact avec les parties brûlantes, ne jamais

travailler avec le bas du moteur au-dessus du niveau de

la taille.

Ne pas toucher les alentours de l’échappement ou du

cylindre, qui deviennent brûlants pendant l’utilisation.

Contact avec les surfaces chaudes pourrait entraîner des

blessures graves.

 Toujours arrêter le moteur et débrancher le fil de la bougie

avant d’effectuer tout entretien ou réglage, à l’exception

des réglages du carburateur.

 Inspecter l’outil avant chaque utilisation pour s’assurer qu’il

n’y a pas de pièces desserrées, de fuites ce carburant, etc.

Remplacer les pièces endommagées avant utilisation.

 Ne jamais utiliser des lames, de dispositifs coudés, un

fil ou une corde avec ce accessoire taille-bordures. Ne

jamais utiliser des lames, un dispositif fouetteur, un fil ou

une corde sur une accessoire.

 Lors d’une utilisation normale, l’accessoire de coupe ne

doit jamais tourner au ralenti. La rotation au ralenti est

toutefois permise lors du réglage du carburateur.

 Il a été rapporté que, chez certaines personnes, les

vibrations produites par les outils à main motorisés peuvent

contribuer au développement d’une affection appelée

syndrome de Raynaud. Les symptômes peuvent inclure des

picotements, l’insensibilisation et le blanchissement des

doigts et sont habituellement provoqués par l’exposition

au froid. L’hérédité, l’exposition au froid et à l’humidité,

le régime alimentaire, la fumée et les habitudes de travail

sont tous des facteurs considérés comme contribuant au

développement de ces symptômes. Il n’existe actuellement

aucune preuve qu’un certain type de vibration ou le degré

d’exposition contribue réellement au développement de

cette affectation. Certaines mesures, susceptibles de réduire

les effets des vibrations, peuvent être prises par l’opérateur :

a) Garder le corps au chaud par temps froid. Pendant

l’utilisation, porter des gants afin de tenir les mains et

les poignets au chaud. Il a été établi que le froid est

l’une des principales causes du symptôme de Raynaud.

b) Après chaque période d’utilisation, faire des exercices

pour accroître la circulation.

La page charge ...

Ryobi C430 Manuel utilisateur

Marque: Ryobi

Modèle: C430

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi C430 User manual
español: Ryobi C430 Manual de usuario

Documents connexes

Autres documents

Homelite ut26csl3, ut26ssl3 Le manuel du propriétaire