Yamaha MCR332 Black Manuel utilisateur

Printed in Malaysia WY88870

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

CD RECEIVER

AMPLI-TUNER CD

CRX-332

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry,

clean place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum clearances

around CRX-332.

Top: 20 cm (8 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to this

unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from a wall outlet or

this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press to set this unit to the

standby mode, and disconnect the AC power plug from

the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the power off, then leave this unit

alone for cooling.

20 Install this unit near the AC outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

22 Excessive sound pressure from earphones and

headphones can cause hearing loss.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt to

service this device.

DANGER

This unit emits visible laser radiation when open. Avoid direct

eye exposure to beam. When this unit is plugged into the wall

outlet, do not place your eyes close to the opening of the disc tray

and other openings to look into inside.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as long as

it is connected to the wall outlet, even if this unit itself is turned off

by . This state is called the standby mode. In this state, this unit is

designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

LASER

Type Semiconductor laser GaAs/GaAlAs

Wave length 790 nm

Output Power 7 mW

WARNING

DO NOT TOUCH THIS UNIT WHEN IT IS USED

CONTINUOUSLY AT HIGH VOLUME BECAUSE THE

BOTTOM OF THIS UNIT MAY BECOME HOT. IT MAY LEAD

TO INJURIES SUCH AS BURNS, ETC.

1 En

PREPARATION OPERATION

ADDITIONAL

INFORMATION

English

SUPPLIED ACCESSORIES ................................. 2

PLAYABLE DISCS AND FILE FORMAT......... 3

CONNECTION....................................................... 4

Connecting speakers/antenna/subwoofer................... 4

Connecting the power cable....................................... 5

Other connection........................................................ 5

REMOTE CONTROL ........................................... 6

FRONT PANEL DISPLAY ................................... 7

FRONT PANEL AND BASIC OPERATION ..... 8

LISTENING TO MUSIC....................................... 9

Playback operation..................................................... 9

Other operation ........................................................ 10

LISTENING TO FM RADIO STATIONS ........ 11

Tuning to radio stations ........................................... 11

Presetting radio stations........................................... 11

Selecting preset radio stations (Preset tuning)......... 11

Displaying Radio Data System information ............ 11

USING USEFUL FUNCTIONS .......................... 12

Using option menu................................................... 12

Using sleep timer ..................................................... 12

TROUBLESHOOTING .......................................13

General..................................................................... 13

iPod/iPad.................................................................. 14

USB/iPad ................................................................. 15

Radio reception........................................................ 15

Disc playback .......................................................... 16

Remote control ........................................................ 16

HANDLING COMPACT DISCS ........................17

SPECIFICATIONS...............................................17

CONTENTS

PREPARATION

OPERATION

ADDITIONAL INFORMATION

■ About this manual

• “iPod” described in this manual may also refer to “iPhone”.

• This manual describes how to operate this unit using a remote control except when it is not available. Some of these

operations are also available using the front panel buttons.

• The symbol “

☞” with page number(s) indicates the corresponding reference page(s).

• Notes contain important information about safety and operating instructions. y indicates a tip for your operation.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of

improvements, etc. In case of differences between the manual and the product, the product has priority.

2 En

PREPARATION

Make sure you have all of the following items.

■ Using the remote control

■ Replacing the battery in the remote control

SUPPLIED ACCESSORIES

Use the remote control within 6 m (20’) of this unit and

point it toward the remote control sensor.

• Do not spill liquid on the remote control.

• Do not drop the remote control.

• Do not leave the remote control in the following places:

– hot or humid places such as a bathroom or near a heater

– extremely cold places

– dusty places

While pushing the release tab in direction , slide out

the battery holder in direction .

Change the battery when the operation range of the

remote control decreases.

• If the battery grows old, the effective operation range of the

remote control decreases considerably. If this happens,

replace the battery with new one as soon as possible.

• Exhausted battery may leak. If the battery have leaked,

dispose of it immediately. Avoid touching the leaked

material or letting it come into contact with clothing, etc.

Clean the battery compartment thoroughly before installing

a new battery.

• Keep the battery away from children. If the battery is

accidentally swallowed, contact your doctor immediately.

• When not planning to use the remote control for long

periods of time, remove the battery from the remote control.

• Do not charge or disassemble the supplied battery.

SLEEP

CD

TUNER

OPTION

MENU

FOLDER

PRESET

ENTER

VOLUME

USB

DISPLAY

MUTE

TUNING

MEMORY

iPod AUX

Remote control FM antenna

(With CR2032 battery)

Dock cover USB cap

Keep the USB cap out of the reach

of children, so that it is not

mistakenly swallowed.

CAUTION

PHONES

PRESET

INPUT

VOLUME

CD

OPTION

MENU

FOLDER

PRESET

ENTER

VOLUME

USB

DISPLAY

MUTE

TUNING

MEMORY

iPod AUX

SLEEP

TUNER

Within 6 m (20’)

Battery insulation sheet:

Remove before using.

Notes

1

2

3

CR2032 battery

Notes

3 En

PREPARATION

English

■ Playable discs

Use compact discs bearing the marks below.

To play back an 8-cm (3 in) CD

Place it in the inner recessed area of the disc tray. Do not

put a normal (12-cm) CD on top of an 8-cm (3 in) CD.

■ Playable MP3 and WMA files

MP3

*

1

Variable bitrate is supported.

WMA

• Version 8

• Version 9 (Standard and variable bitrates are supported.

Professional and Lossless are not supported.)

*

2

Both constant and variable bitrates are supported.

• Playback for Data Disc starts in alphanumeric order of files.

• Playback for USB starts in order by date and time of creation.

• Copyright-protected WMA (DRM) files cannot be played back

by this unit.

• The disc must be ISO 9660 compatible.

• The maximum file and folder numbers are as follows.

*

3

The root is counted as one of the folders.

PLAYABLE DISCS AND FILE FORMAT

....

Compact discs (digital audio)

....

CD-R,CD-RW digital audio discs

• CD-R or CD-RW discs bearing one of

the following phrases.

FOR CONSUMER

FOR CONSUMER USE

FOR MUSIC USE ONLY

• Finalized CD-R or CD-RW discs

This compact disc player may not be able to

play some CD-R/CD-RW discs or discs on

which recording was not made correctly.

....

CD-TEXT discs

To prevent a malfunction of this unit:

• Do not use any nonstandard shaped

disc (heart, etc.) available on the

market because it might damage the

unit.

• Do not use a disc with tape, stickers, or paste on it. If

you use such a disc, the disc may get stuck in the

unit, or damage to the unit may result.

Note: Do not use any lens cleaners as they may be a

cause of malfunction.

Note

Format

Bitrate

(kbps)

Sampling

frequency

(kHz)

MPEG 1 Audio Layer-3

32-320

*1

32/44.1/48

MPEG 2 Audio Layer-3, 2

8-160

*1

16/22.05/24

Profile

Bitrate

(kbps)

Sampling

frequency

(kHz)

High Profile

32-320

*2

32/44.1/48

Mid Profile

16-32 22.05

Notes

Data Disc USB

Maximum total number of file

and folder

*3

512 9,999

Maximum folder number

*3

255 999

Maximum file number per

folder

511 255

4 En

Follow the procedure below to connect the speakers and FM antenna to this unit. For information on your speakers, refer

to the owner’s manual supplied for the speakers.

If a subwoofer is connected, low-frequency audio signals are output through SUBWOOFER OUT.

Do not connect the power cable of this unit until all cable connections are completed.

• If you connect a subwoofer, use a subwoofer that has a built-in amplifier.

• Be sure to connect the left channel (L), right channel (R), “+”(red) “–”(black) properly. If the connections are faulty, no sound will be

heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lacks bass.

• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/

or the speakers.

• Use speakers having more than 6 Ω impedance.

• There is a chance that placing speakers too close to a CRT-based (Braun tube) TV set might impair picture color. Should this happen,

move the speakers away from the TV set.

CONNECTION

Connecting speakers/antenna/subwoofer

CAUTION

Notes

FM antenna

• The antenna should be stretched out.

• If you use an outdoor antenna instead of the supplied FM

antenna, reception will be better.

• If radio reception is poor, change the height, direction, or

placement of the antenna.

• If you use an FM antenna that is not supplied with the unit,

make sure that the base of the antenna is not threaded.

Notes

Subwoofer cable

(sold separately)

Subwoofer (sold

separately)

Be sure to remove insulation

from the end of each speaker

cable.

CONNECTION

5 En

PREPARATION

English

After you made all connections, connect the power cables

of this unit

■ Stationing iPod

Station or remove your iPod whenever you want.

y

An iPod is charged when set in the iPod dock.

When the unit is turned on and the input source is set to USB, the

iPod is not charged.

This unit is compatible with iPod classic, iPod nano (2nd

generation and later), iPod touch and iPhone.

• To secure the connection, attach a compatible Dock Adapter

supplied with the iPod or an iPod Universal Dock Adapter (sold

separately), and remove the protective case covering from your

iPod.

• If you do not use an adapter or if the adapter is not compatible,

the connection could be loose or poor, which could cause

damage or malfunctions. For details on dock adaptor

information, please visit official Apple’s website.

• If an iPod in protective case is connected by force, the

connector may be damaged. Remove the protective case before

connection.

• Attach the dock cover to the iPod dock whenever you are not

using it.

■ Connecting iPad

Connect or remove your iPad whenever you want.

y

When the unit is turned on and the input source is set to USB, the

connected iPad is charged.

• Make sure to use a Dock Connector to USB Cable that is

supplied with your iPad.

• When an iPad or USB device is not in use, set the USB cover to

protect USB port.

■ Connecting a USB device

Connect or remove your USB device whenever you want.

y

When the unit is turned on and the input source is set to USB, the

connected USB device is charged.

• This unit supports USB mass storage class devices (e.g., flash

memories or portable audio players) using FAT16 or FAT32

format.

• Do not connect devices other than USB mass storage class

devices (such as USB chargers or USB hubs), PCs, card

readers, an external HDD, etc.

• USB devices that use encryption cannot be used.

• When an iPad or USB device is not in use, set the USB cover to

protect USB port.

■ Connecting an external device

Connect your portable audio device using a commercially

available 3.5 mm (1/8 in) mini plug cable.

Connecting the power cable

Other connection

Note

Notes

To the wall

outlet

IPod

USB

Dock Adapter

iPod dock

Note

Notes

IPod

USB

IPod

USB

6 En

1 Infrared signal transmitter

2 SLEEP: Sleep setting (☞ P. 12)

3 Source buttons: Change sources.

4 FOLDER (during data CD/USB playback): Change folder.

5 , : Scrolls through items on the iPod’s screen.

6 OPTION: Displays the option menu. (☞ P. 12)

7 (Shuffle), (Repeat) (☞ P. 10)

8 TUNING (during receiving radio): Tuning radio (☞ P. 11)

9 PRESET (during receiving radio): Select the preset radio

station (☞ P. 11)

0 : Standby/on

A , (during playback): Skip backward and forward/

press and hold to rewind and fast-forward

MENU: Returns to the upper level in the iPod menu.

: Play/pause

S/T/W/X (During using the option menu): Changes the

setting

ENTER

(During using the iPod): Select group/start playback

(During using the option menu): Confirms the setting

B : Stop playback.

C DISPLAY: Switches the information shown on the front

panel. (☞ P. 10)

D MUTE: Mute/resume the sound.

E VOLUME: Volume control

F MEMORY: Memories preset radio stations. (☞ P. 11)

REMOTE CONTROL

SLEEP

CD

TUNER

OPTION

MENU

FOLDER

PRESET

ENTER

VOL UME

USB

DISPLAY

MUTE

TUNING

MEMORY

iPod AUX

2

6

7

3

5

8

9

4

A

0

B

C

D

E

F

1

7 En

PREPARATION

English

1 SLEEP indicator: Lights up when the sleep timer is on

(☞ P. 12).

2 PRESET indicator: Lights up when you preset radio

stations (☞ P. 11).

3 STEREO indicator: Lights up when this unit is receiving a

strong signal from an FM stereo broadcast.

4 AUTO indicator: Lights up when this unit is in the

Automatic Tuning mode (☞ P. 11).

5 SHUFFLE indicator: Lights up when you set your

iPod/iPad/CD/USB to shuffle play (☞ P. 10).

6 REPEAT indicator: Lights up when you set your

iPod/iPad/CD/USB to repeat play (☞ P. 10).

7 Radio Data System indicators: The name of the Radio

Data System data offered by the currently received Radio

Data System station lights up (☞ P. 11).

8 MUTE indicator: Lights up when the sound is muted.

9 Multi information display: Shows the various

information.

0 TUNED indicator: Lights up when this unit is tuned into a

station (☞ P. 11).

A MEMORY indicator: Flashes when searching for a radio

station by automatic preset tuning. Lights up when you preset

radio stations automatically or manually (☞ P. 11).

B Multi information indicators: Indicate the music

information currently displayed on Multi information display

(☞ P. 10).

C Operation indicators: Shows the available menu buttons

for the currently selected OPTION menu item.

FRONT PANEL DISPLAY

PHONES

PRESET

INPUT

VOLUME

SONGS

ALBUMS

ARTISTS

MEMORY

TUNED

SLEEP

STEREO

AUTO

SHUFFLE

MUTE

PRESET

12 34 8756

0A B

C

9

REPEAT

PS

PTY RT CT

8 En

OPERATION

y

• Press to set the unit to standby mode. All the information on the front panel display is not displayed in standby mode. This can

reduce power consumption. To turn on the unit, press , , or on the front panel. If you press , the input source

is set to CD, iPod or USB depending on which input source is used last. Playback begins if the input source is set to CD or USB.

FRONT PANEL AND BASIC OPERATION

PHONES

PRESET

INPUT

VOLUME

IPod

USB

VOLUME

iPod dock

CD iPod AUX USB FM

:

Unit standby/on

:

Disc tray open/close

:

Stop playback

INPUT button:

Press repeatedly to choose the input source.

VOLUME

USB port:

☞ P. 5, 9

PHONES:

Connecting headphones

y

To listen to an external device, select AUX

and use the external device to begin

playback.

No sound is output from the speakers

when headphones are connected.

Down Up

Disc tray

:

Play/pause playback

(During playback):

Skip and search backward/forward.

PRESET (During receiving radio):

Select the preset radio station.

3.5 mm (1/8 in) mini plug cable

Remote control sensor:

Receives signals from the remote

control.

9 En

OPERATION

English

Follow the procedures below to play back music.

*

1

Some features may not be available depending on the model or the software version of your iPod/iPad.

*

2

· Some devices may not work properly even if they meet the requirements.

· Playability of and power supply to all kind of USB devices are not guaranteed.

· The reading time may exceed 30 seconds depending on the number of files/folders.

· Yamaha and suppliers accept no liability for the loss of data saved on the USB devices connected to this unit.

As a precaution, it is recommended that the files are made backup copies.

*

3

· If you press these buttons, the folder name is displayed on the front panel display for a certain period.

· ROOT is displayed for the root folder when the directory contains playable files.

LISTENING TO MUSIC

Playback operation

Set the source

Switch the

input

Select music and start playback

iPod

*1

iPad

*1

USB

*2

CD

1

2

3

IPod

USB

☞ P. 5

Dock Adapter

iPod

MENU

ENTER

Scroll the list

Control menu

IPod

USB

☞ P. 5

USB

IPod

USB

☞ P. 5

OPTION

MENU

FOLDER

ENTER

Skip to the first file in the previous/next

folder for MP3 or WMA

*3

PHONES

PRESET

INPUT

VOLUME

CD

LISTENING TO MUSIC

10 En

■ Control playback

: Skip forward/Press and hold to Fast forward

: Skip backward/Press and hold to Rewind

: Play/Pause

: Stop

• Playback for Data Disc starts in alphanumeric order of files.

• Playback for USB starts in order by date and time of creation.

• If is pressed during playback, next time playback starts

from the beginning of the track you listened to last time. If

is pressed again while playback is stopped, next time playback

starts from the first track of the CD/USB device.

• This unit automatically switch the unit to standby mode if the

unit is left turned on for 1 hour without playback or any other

operation being performed (Automatic standby function).

■ Shuffle play

You can play back in random sequence.

For iPod/iPad

*

1

You cannot set SHUFFLE ALBUMS when you use an iPod

touch, iPhone or iPad.

For CD/USB

*

2

If the audio format of the selected music source is MP3/

WMA, you can also select SHUFFLE FOLDER.

■ Repeat play

You can play back repeatedly.

For iPod/iPad

For CD/USB

*

3

If the audio format of the selected music source is MP3/

WMA, you can also select REPEAT FOLDER.

■ Switching the display

You can switch the playback information shown on the

front panel display. Some special characters may not be

shown properly.

For iPod/iPad

Song number and elapsed time (default setting)

↓

Song number and remaining time

↓

Song name

↓

Artist name

↓

Album name

↓

Back to the default setting

This function is available for iPod classic, iPod nano (2nd

generation and later), iPod touch, iPhone and iPad. However,

even with these models, this function may not be available

depending on the software version of your iPod/iPad.

For CD/USB

Track/file number and elapsed time of the current

song (default setting)

↓

Track number and remaining time of the current

song

*4

↓

Total time of the disc

*4

↓

Remaining time of the disc

*4

↓

File name

*5

↓

Track name

*6

↓

Artist name

*6

↓

Album name

*6

↓

Back to the default setting

*

4

Only for Audio CDs

*

5

Only for MP3/WMA files

*

6

Only when the selected track has information

Other operation

Notes

1 2

During playback

OPTION

MENU

ENTER

Press repeatedly.

Note

DISPLAY

Press repeatedly.

1 2

During playback

11 En

OPERATION

English

y

If the signal received from the station you want to select is weak,

you can also tune into radio stations manually by pressing

TUNING repeatedly.

If you tune to a station manually, the sound is monaural.

You can store your favorite FM stations with the preset

function.

■ Automatic preset tuning

y

To cancel automatic presetting, press MEMORY again without

pressing ENTER in step 2.

When you perform the automatic preset, all stored stations are

cleared and the new stations are stored.

■ Manual preset tuning

y

• You can preset up to 30 FM stations.

• To cancel the manual preset while choosing a preset number,

press MEMORY again.

• You can delete a preset station by pressing OPTION →

Cursor S/T → ENTER to select PRESET DELETE.

PS (Program Service)

↓

PTY (Program Type)

↓

RT (Radio Text)

↓

CT (Clock Time)

↓

Frequency

↓

Back to the PS

If the signal transmission of the Radio Data System station is too

weak, this unit may not be able to receive Radio Data System

information completely. In particular, RT (Radio Text)

information uses a lot of bandwidth, so it may be less available

compared to other types of information.

LISTENING TO FM RADIO STATIONS

Tuning to radio stations

Note

Presetting radio stations

Note

TUNER

TUNING

Press TUNER. Press and hold.

Automatic tuning starts.

1 2

MEMORY

ENTER

Press and hold

MEMORY for more than

2 seconds in FM mode.

Start the automatic preset.

1 2

TUNING

MEMORY

MENU

ENTER

Tune into a favorite

radio station.

Press MEMORY.

Select the preset

number you want to

store to.

Complete the

manual preset.

1 2

3 4

Selecting preset radio stations

(Preset tuning)

Displaying Radio Data System

information

Note

PRESET

Select the preset radio station

in FM mode.

DISPLAY

1 2

Press repeatedly.While listening

12 En

The option menu appears on the front panel display by pressing OPTION. You can set various useful functions with

option menu.

*

1

To set additional items, repeat steps 2 to 5.

y

To cancel the setting during the operation, press OPTION.

■ Setting dimmer, tone/balance

DIMMER: Changes the brightness of the front panel display.

TREBLE

*2

: Adjusts the high frequency response.

BASS

*2

: Adjusts the low frequency response.

BALANCE: Adjusts the volume level of each left and right speaker channel.

*

2

Also effective when you are using headphones.

The sleep timer sets the unit to the standby mode after the specified time elapses.

The SLEEP indicator lights up on the front panel display (☞ P. 7).

USING USEFUL FUNCTIONS

Using option menu

Option menu Parameter or control range Reference page

PRESET DELETE (Displays only when the input source is set to FM.) 11

DIMMER DIMMER OFF (brightest)/DIMMER 1/DIMMER 2 (darkest) This page

TREBLE –10 to +10 This page

BASS –10 to +10 This page

BALANCE L+5 - CENTER - R+5 This page

AUTO POWER OFF

TIME OFF/ TIME 8H/ TIME 4H

AUTO POWER OFF sets the system to standby mode whenever no

operation is performed for a preset amount of time.

This page

MENU

ENTER

MENU

ENTER

OPTION

ENTER

Press OPTION. Select desired

option menu.

Change the settings.

1 2 3 4 5

Exit option

menu.

6

ENTER

OPTION

Confirm with

ENTER.

Complete the

setting.*

1

Using sleep timer

SLEEP

Press repeatedly.

30min 60min 90min 120min OFF

13 En

ADDITIONAL

INFORMATION

English

ADDITIONAL INFORMATION

Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below

or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized

Yamaha dealer or service center.

TROUBLESHOOTING

General

Problem Cause Remedy Page

This unit fails to turn

on or enters the

standby mode soon

after the power is

turned on.

The unit does not

operate properly.

The power cable is not connected or the

plug is not completely inserted.

Connect the power cable firmly.

5

This unit has been exposed to a strong

external electric shock (such as lightning

or strong static electricity).

Press and hold for more than 5 seconds to reset

the system. If this does not solve the problem, set this

unit to the standby mode, disconnect the power

cable, plug it back in after 30 seconds and then use it

normally.

—

No sound. No appropriate input source has been

selected.

Select an appropriate input source with INPUT on

the front panel (or the source buttons on the remote

control).

—

Speaker connections are not secure. Secure the connections.

4

The mute function may be on. Cancel the mute function.

6

The volume is turned down. Turn up the volume.

8

Signals this unit cannot reproduce are

being input from a source component,

such as a CD-ROM.

Play a source whose signals can be reproduced by

this unit.

3

The power is

suddenly turned off.

The sleep timer may be set. This is not malfunction. Turn on the unit and play the

source again.

—

The unit is left turned on for 1 hour

without playback or any other operation

being performed.

AUTO POWER OFF is triggered. Setting AUTO POWER OFF to TIME OFF enables

to play continuously.

12

Sound is heard from

the speaker on one

side only.

Incorrect cable connections. Connect the cables properly. If the problem persists,

the cables may be defective.

4

There is noise

interference from

digital or radio

frequency

equipment.

This unit is too close to the digital or

high-frequency equipment.

Move this unit farther away from such equipment.

—

TROUBLESHOOTING

14 En

In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to your iPod/iPad

(see page 5).

* Messages shown above appear only when a device is connected to the iPod dock.

iPod/iPad

Note

Status message Cause Remedy Page

iPod Connecting

iPod Charging

This unit is in the middle of recognizing

the connection with your iPod.

If the message continues to appear in the front panel

display, disconnect and connect the iPod again.

5

Unknown iPod

There is a problem with the signal path

from your iPod to this unit.

Connect the iPod again.

5

The iPod being used is not supported by

this unit.

Only iPod classic, iPod nano (2nd generation and

later), iPod touch and iPhone are supported.

—

iPod

This unit has recognized your iPod;

however, it cannot obtain information

such as elapsed time.

iPod Unplugged

Your iPod was removed. Connect the iPod again.

5

Over Current

The iPod being used is not supported by

this unit.

Disconnect the iPod and then turn the unit off and on

again. Then connect supported iPod again.

5

The iPod is connected at an angle.

Problem Cause Remedy Page

No sound. The power of the unit is off. Connect the power cable correctly.

—

The iPod/iPad software version has not

been updated.

Download the latest iTunes software to update the

iPod/iPad software version to the latest.

—

The iPod/iPad is in the process of

connecting with the unit.

Please wait for a while.

—

The iPod/iPad is not connected correctly. Remove the iPod/iPad from the unit, then connect it

again.

5

The iPod/iPad

sounds, but you

cannot operate it with

the unit or the remote

control.

The iPod/iPad is not connected correctly. Remove the iPod/iPad from the unit, then connect it

again.

5

You cannot operate

from the iPod/iPad.

The iPod/iPad is not connected correctly. Remove the iPod/iPad from the unit, then connect it

again.

5

The playback

information is not

displayed on the

front panel display.

The iPod/iPad you set is not compatible

with the playback information display.

Only iPod classic, iPod nano (2nd generation and

later), iPod touch, iPhone and iPad are supported.

5

The iPod/iPad does

not charge up.

The iPod/iPad is not connected correctly. Remove the iPod/iPad from the unit, then connect it

again.

5

Suddenly the music

being played back is

canceled and another

track starts playing

without performing

any operation.

The iPod’s Shake to Shuffle function is

turned on.

Turn off the Shake to Shuffle function in the iPod’s

settings.

—

TROUBLESHOOTING

15 En

ADDITIONAL

INFORMATION

English

In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to the USB device

(see page 5).

USB/iPad

Note

Status message Cause Remedy Page

USB Unplugged

The USB device is not connected

firmly.

Connect the USB device again.

5

Unknown USB

The connected USB device is not

playable on this unit.

Connect playable USB device.

5

The file name is too long. The file name should be no more than 250

characters.

—

Over Current

The USB device is connected at an

angle.

Disconnect the USB device and then turn the unit off

and on again. Then connect playable USB device

again.

5

No Files

The USB device does not contain

playable files.

Use a USB device contains playable files.

3

An incompatible USB device is

connected to the unit.

Turn off the system and reconnect the USB device to

the unit. If it does not resolve the problem, the USB

device is not playable on the unit.

—

USB Time Out

The number of files/folders exceeds the

limit.

Reduce the number of files/folders; refer to the

limitations noted in this manual.

3

Problem Cause Remedy Page

MP3/WMA file in the

USB device does not

play.

The USB device is not recognized. Connect the USB device again.

5

Connect an AC adapter if supplied with the device.

—

Format the USB device and copy the files again.

—

Improper USB device connections. Connect the USB device again.

5

The MP3 or WMA formats are not

compatible with this unit.

Replace the file with a correctly recorded file

playable with this unit.

3

If the solutions above do not resolve the

problem, the USB device is not playable

on the unit.

Try another USB device.

—

Radio reception

Problem Cause Remedy Page

FM stereo reception is

noisy.

The antenna is connected improperly. Check the antenna connections.

4

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

Try using a high-quality directional FM antenna.

—

Use the manual tuning method.

11

The desired station

cannot be tuned into

with the automatic

tuning method.

The signal is too weak. Use a high-quality directional FM antenna.

—

Use the manual tuning method.

11

The preset selecting

function does not work.

The preset (memory) may have been

erased.

Preset radio stations again.

11

There is distortion,

and clear reception

cannot be obtained

even with a good FM

antenna or an outdoor

antenna.

Multipath reflection or other radio

interference may have occurred.

Change the height, direction, or placement of the

antenna.

—

TROUBLESHOOTING

16 En

Disc playback

Problem Cause Remedy Page

No sound or

distorted sound

The sampling rate of an MP3 or WMA

file may not be compatible with this unit.

Check the sampling rate and bit rate of an MP3 or

WMA file are compatible with this unit.

3

Disc playback does

not start.

You may be using a CD-R/RW that is not

finalized.

Finalize the CD-R/RW.

—

The disc label may be upside down. Check that the disc label is facing up.

—

The disc may be defective. Try playing back another disc. If this cures the

problem, the disc you want to play back is defective.

—

MP3/WMA disc may not contain

sufficient music files to be played back.

Check that your MP3/WMA disc contains at least

5 MP3/WMA music files. If the number of files is

small, the disc may not be recognized.

—

The sampling rate of an MP3 or WMA

file may not be compatible with this unit.

Check the sampling rate and bit rate of an MP3 or

WMA file are compatible with this unit.

3

Some button

operations do not

work.

The disc loaded into the unit may not be

compatible.

Remove the disc and then check whether the unit

supports the disc or not.

3

Playback does not

start immediately

after pressing

on the unit or on

the remote control.

The disc may be dirty. Wipe the disc clean.

—

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit.

3

If the unit was moved from a cold to

warm place, condensation may have

formed on the disc reading lens.

Wait for an hour or two until the unit adjusts to the

room temperature, and try again.

—

“No Disc” appears in

the display even

though a disc is in

the disc tray.

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit.

3

The disc may be dirty. Remove the disc and then wipe the disc clean.

—

Disc is loaded upside-down. Remove the disc and then load the disc with the

labeled side facing up.

—

Remote control

Problem Cause Remedy Page

The remote control

does not work nor

function properly.

The remote control may be operated

outside its operation range.

For information on the remote control operation

range, refer to “Using the remote control”.

2

The remote control sensor on this unit

may be exposed to direct sunlight or

lighting.

Change the lighting or orientation of this unit.

—

The battery may be worn out. Replace the battery with new one.

2

There are obstacles between the sensor of

this unit and the remote control.

Remove the obstacles.

—

17 En

ADDITIONAL

INFORMATION

English

• Always handle with care so that the playing surface is

not scratched. Do not bend discs.

• To keep the playing surface clean, wipe with a clean,

dry cloth. Do not use any type of disc cleaner, spray, or

any other chemical-based liquid.

• Do not expose discs to direct sunlight, high temperature

or high humidity for a long time.

• Do not wipe with a circular motion; wipe straight

outward from the center.

• Use a soft-tipped pen when writing on the label side of a

disc.

PLAYER SECTION

iPod

• Supported iPod.............................................................iPod classic,

iPod nano (2nd generation and later), iPod touch, iPhone, iPad

CD

• Media ......................................................................CD, CD-R/RW

• Audio format............................................. Audio CD, MP3, WMA

LASER

• Type ........................................Semiconductor laser GaAs/GaAlAs

• Wave length.........................................................................780 nm

• Output Power.......................................................................10 mW

USB

• Audio format................................................................MP3, WMA

AUX

• Input connector .......... STEREO L/R: 3.5 mm STEREO mini Jack

AMPLIFIER SECTION

• Maximum output power ............................................20 W + 20 W

(6 Ω 1 kHz, 10% THD)

• Input impedance (AUX) ........................................................73 kΩ

• Maximum input signal (AUX)................................................2.2 V

• Total harmonic distortion

CD etc. 1 kHz/8 W............................................................... 0.04 %

TUNER SECTION

• Tuning range

[U.S.A. and Canada models] ......................... 87.5 to 107.9 MHz

[Other models]........................................... 87.50 to 108.00 MHz

GENERAL

• Power Supply

[Europe model] .................................................AC 230 V, 50 Hz

[U.S.A. and Canada models] ............................AC 120 V, 60 Hz

[Asia model] ........................................ AC 220-240 V, 50/60 Hz

[Taiwan model]......................................... AC 110-120 V, 60 Hz

[Australia model]..............................................AC 240 V, 50 Hz

[U.K. model].....................................................AC 230 V, 50 Hz

[China model] ...................................................AC 220 V, 50 Hz

[Korea model]...................................................AC 220 V, 60 Hz

• Power consumption ................................................................32 W

• Standby Power consumption...................................... 0.3 W or less

• Dimensions (W × H × D)........................... 180 × 118 × 318.2 mm

(7 1/8 × 4 5/8 × 12 1/2 in)

• Weight..................................................................2.95 kg (6.5 lbs.)

Specifications are subject to change without notice.

iPod, iPhone, iPad

“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean

that an electronic accessory has been designed to connect

specifically to iPod, iPhone, or iPad, respectively, and has been

certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod, iPhone, or

iPad may affect wireless performance.

iPad, iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and

iPod touch are trademarks of Apple Inc., registered in the U.S.

and other countries.

HANDLING COMPACT DISCS

SPECIFICATIONS

i Fr

1 Pour utiliser l’appareil au mieux de ses possibilités,

lisez attentivement ce mode d’emploi. Conservez-le

soigneusement pour référence.

2 Installez cet ensemble audio dans un endroit bien aéré,

frais, sec et propre - veillez à ce qu’il soit à l’abri de la

lumière directe du soleil, des sources de chaleur, des

vibrations, des poussières, de l’humidité et/ou du froid.

Pour une ventilation correcte, ménagez l’espace

minimum suivant autour du CRX-332.

Au-dessus : 20 cm

À l’arrière : 10 cm

Sur les côtés : 10 cm

3 Placez l’appareil loin des équipements, moteurs et

transformateurs électriques, pour éviter les ronflements

parasites.

4 N’exposez pas l’appareil à des variations brutales de

température, ne le placez pas dans un environnement très

humide (par exemple dans une pièce contenant un

humidificateur) car cela peut entraîner la condensation

d’humidité à l’intérieur de l’appareil qui elle-même peut

être responsable de décharge électrique, d’incendie, de

dommage à l’appareil ou de blessure corporelle.

5 Evitez d’installer l’appareil dans un endroit où des objets

peuvent tomber, ainsi que là où l’appareil pourrait être

exposé à des éclaboussures ou des gouttes d’eau. Sur

le dessus de l’appareil, ne placez pas :

– d’autres appareils qui peuvent endommager la surface

de l’appareil ou provoquer sa décoloration.

– des objets se consumant (par exemple, une bougie)

qui peuvent être responsables d’incendie, de

dommage à l’appareil ou de blessure corporelle.

– des récipients contenant des liquides qui peuvent être

à l’origine de décharge électrique ou de dommage

à l’appareil.

6 Ne couvrez pas l’appareil d’un journal, d’une nappe,

d’un rideau, etc. car cela empêcherait l’évacuation de la

chaleur. Toute augmentation de la température intérieure

de l’appareil peut être responsable d’incendie, de

dommage à l’appareil ou de blessure corporelle.

7 Ne branchez pas la fiche du câble d’alimentation de

l’appareil sur une prise secteur aussi longtemps que tous

les raccordements n’ont pas été effectués.

8 Ne pas faire fonctionner l’appareil à l’envers. Il risquerait

de chauffer et d’être endommagé.

9 N’exercez aucune force excessive sur les commutateurs,

les boutons et les cordons.

10 Pour débrancher la fiche du câble d’alimentation au niveau de

la prise secteur, saisissez la fiche et ne tirez pas sur le cordon.

11 Ne nettoyez pas l’appareil au moyen d’un solvant

chimique, ce qui pourrait endommager la finition.

Utilisez un chiffon sec et propre.

12 N’alimentez l’appareil qu’à partir de la tension prescrite.

Alimenter l’appareil sous une tension plus élevée est

dangereux et peut être responsable d’incendie, de

dommage à l’appareil ou de blessure corporelle. Yamaha

ne saurait être tenue responsable des dommages résultant

de l’alimentation de l’appareil sous une tension autre que

celle prescrite.

13 Pour empêcher tout dommage causé par les éclairs,

déconnectez le câble d’alimentation et toute antenne

extérieure de la prise murale pendant un orage.

14 Ne tentez pas de modifier ni de réparer l’appareil.

Consultez le service Yamaha compétent pour toute

réparation qui serait requise. Le coffret de l’appareil ne

doit jamais être ouvert, quelle que soit la raison.

15 Si vous envisagez de ne pas vous servir de l’appareil

pendant une longue période (par exemple, pendant les

vacances), débranchez la fiche du câble d’alimentation

au niveau de la prise secteur.

16 Lisez la section intitulée « GUIDE DE DÉPANNAGE »

où figurent une liste d’erreurs de manipulation communes

avant de conclure que l’appareil présente une anomalie de

fonctionnement.

17 Avant de déplacer l’appareil, appuyez sur pour placer

l’appareil en veille puis débranchez la fiche du cordon

d’alimentation au niveau de la prise secteur.

18 La condensation se forme lorsque la température

ambiante change brusquement. En ce cas, débranchez la

fiche du câble d’alimentation et laissez l’appareil reposer.

19 La température de l’appareil peut augmenter en raison

d’une utilisation prolongée. En ce cas, coupez

l’alimentation de l’appareil et laissez-le au repos pour

qu’il refroidisse.

20 Installez cet appareil à proximité de la prise secteur et

à un emplacement où la fiche du câble d’alimentation

est facilement accessible.

21 Les piles ne doivent pas être exposées à une chaleur

extrême, par exemple au soleil, à une flamme, etc.

22 Une pression excessive du son par les écouteurs et le

casque d’écoute peut entraîner la perte de l’ouïe.

SÉCURITÉ LASER

L’appareil utilise un laser. En raison des risques de blessure des

yeux, le retrait du couvercle ou les réparations de l’appareil

devront être confiés exclusivement à un technicien d’entretien

qualifié.

DANGER

Risque d’exposition au laser en cas d’ouverture. Eviter

l’exposition directe des yeux au faisceau. Lorsque cet appareil

est branché à la prise de courant, ne pas approcher les yeux de

l’ouverture du plateau changeur et des autres ouvertures pour

regarder à l’intérieur.

ATTENTION : VEUILLEZ LIRE CE QUI SUIT AVANT D’UTILISER

L’APPAREIL.

Cet appareil n’est pas déconnecté du secteur tant qu’il reste branché

à la prise de courant, même si l’appareil en soi est éteint par

la touche . Il se trouve alors « en veille ». En mode veille,

l’appareil consomme une très faible quantité de courant.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE

DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL

À LA PLUIE OU À L’HUMIDITÉ.

LASER

Type Laser semi-conducteur GaAs/GaAlAs

Longueur d’onde 790 nm

Puissance de sortie 7 mW

AVERTISSEMENT

LORSQUE VOUS UTILISEZ CET APPAREIL À UN VOLUME

ÉLEVÉ PENDANT UNE PÉRIODE PROLONGÉE, IL EST

POSSIBLE QUE LA PARTIE INFÉRIEURE CHAUFFE. PAR

CONSÉQUENT, NE TOUCHEZ PAS L’APPAREIL, CAR VOUS

RISQUEZ DE VOUS BLESSER, ET NOTAMMENT DE VOUS

BRÛLER.

La page charge ...

Yamaha MCR332 Black Manuel utilisateur

Ce manuel convient également à

Yamaha MCR332 Black Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents