Hestan KRT364GDNG Guide d'installation

Marque: Hestan

Modèle: KRT364GDNG

Catégorie: Cuisinières

Taper: Guide d'installation

Ce manuel convient également à

INDOOR COOKING

Professional Rangetop

KRT

Installation Manual

SAFETY DEFINITIONS

THIS INDICATES THAT DEATH OR SERIOUS INJURY MAY OCCUR

AS A RESULT OF NOT OBSERVING THIS WARNING.

THIS INDICATES THAT MINOR OR MODERATE INJURY MAY

OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

THIS INDICATES THAT DAMAGE TO THE APPLIANCE OR

PROPERTY MAY OCCUR AS A RESULT OF NOT OBSERVING THIS

WARNING.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE

INSTALLING OR USING YOUR APPLIANCE TO REDUCE THE RISK OF FIRE,

BURN HAZARD, OR OTHER INJURY. KEEP THIS MANUAL FOR FUTURE

REFERENCE.

CAUTION

NOTICE

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

1. Do not try and light any appliance.

2. Do not touch any electrical switch.

3. Do not use any phone in your building.

4. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

5. If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas

supplier.

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY,

A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE,

PERSONAL INJURY, OR DEATH.

INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.

HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

1 SAFETY PRECAUTIONS - BEFORE YOU BEGIN

2 MODEL NUMBERS

3 RATING LABEL

3 REGULATORY / CODE REQUIREMENTS

3 LOCATION AND INSTALLATION / VENTILATION

7 BACKGUARD AND ACCESSORIES

8 ELECTRICAL CONNECTIONS

8 GAS CONNECTIONS

10 FINAL SETUP

11 SERVICE

12 APPENDIX

TABLE OF CONTENTS

When properly cared for, your Hestan appliance will provide safe, reliable service for many years.

When using this appliance, basic safety practices must be followed as outlined below.

IMPORTANT: Save these instructions for the local Gas or Utility Inspector’s use.

INSTALLER: Please leave these Installation Instructions with the owner.

OWNER: Please retain these Installation Instructions for future reference.

This rangetop is NOT designed for installation in manufactured (mobile) homes or recreational park

trailers. Do NOT install this rangetop outdoors.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Before turning

power ON, be sure all controls are in the OFF position. Failure to do so can

result in electrical shock or death.

ELECTRICAL GROUNDING

This appliance must be grounded. Grounding reduces the risk of electric

shock in the event of a short circuit. Read the ELECTRICAL CONNECTIONS

section of this manual for complete instructions.

This appliance is equipped with a 3-prong grounding plug for your protection against shock hazard

and should be directly plugged into a properly grounded receptacle. Do not cut or remove the

grounding prong from this plug.

ELECTRICAL SUPPLY

The appliance must be on its own dedicated circuit - 120 VAC, Single Phase, 60 Hz, with a current

rating of 15 Amps. Have the installer show you where the electric circuit breaker is located so

you know how to shut off the power to this appliance. It is the responsibility of the user to have

the appliance connected by a licensed electrician in accordance with all local codes, or in the

absence of local codes, in accordance with the National Electrical Code. Read the ELECTRICAL

CONNECTIONS section of this manual for complete details.

MODEL NUMBERS

RANGETOP MODELS

MODEL NO. DESCRIPTION

CIRCUIT BREAKER

REQUIRED

KRT365-NG / -LP 36” RANGETOP WITH 5 BURNERS 15 Amp

KRT364GD-NG / -LP 36” RANGETOP WITH 4 BURNERS & GRIDDLE 15 Amp

KRT485GD-NG / -LP 48” RANGETOP WITH 5 BURNERS & GRIDDLE 15 Amp

REGULATORY / CODE REQUIREMENTS

Installation of this cooking appliance must be made in accordance with local codes. In the absence

of local codes, this unit should be installed in accordance with the National Fuel Gas Code

ANSI

Z223.1/NFPA 54

, Natural Gas and Propane Installation code

CSA B149.1

, or Propane Storage and

Handling Code

B149.2

All Electrical Components must be electrically grounded in accordance with local codes or in the

absence of local codes with the National Electrical Code

ANSI/NFPA 70

, or Canadian Electrical code

CSA C22.1

STATE OF MASSACHUSETTS

Massachusetts requires all gas be installed using a plumber or gas fitter carrying the appropriate

Massachusetts license. All permanently installed natural gas or propane installations require a

T handle type manual gas valve be installed in the gas supply line to this appliance. Flexible gas

connector must not be longer than 36” [91.4 cm].

CALIFORNIA PROPOSITION 65 - WARNING

WARNING This product can expose you to chemicals including carbon monoxide, which is

known to the State of California to cause cancer.

For more information, go to www.P65Warnings.ca.gov.

RATING LABEL

The rating label contains important information about your

Hestan appliance such as the model and serial number,

gas type and manifold pressure, electrical rating, the BTU

rating for each burner type, and the minimum installation

clearances.

The rating label is located underneath the unit.

If service is necessary, contact Hestan Customer Care with

the model and serial number information shown on the label.

LOCATION AND INSTALLATION / VENTILATION

UNPACKING AND PLACEMENT

Remove the outer carton and packing materials. Do not remove the plastic film covering the

stainless-steel surfaces. This film protects the finish from scratches until the appliance is installed in

its final position.

The unit is somewhat heavy and should be handled with care. Use proper safety equipment, such

as gloves, and at least 2 persons to move the appliance into position to avoid injury and to avoid

damage to the floor or the appliance itself.

RATING

LABEL

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

GAS

SUPPLY

APPLIANCE

SHUTOFF VALVE

IN OPEN POSITION

PREPARATION

Before moving the rangetop, remove the grates, burner caps, and any other loose items.

The rangetop must be mounted on a stable platform, as illustrated on the following pages. The

platform must include a 6” x 12” [15.2 x 30.5 cm] cutout at the left rear to allow for the gas and

electrical connections. The platform must also be level to ensure an even cooking surface, especially

for those models featuring a griddle. The platform should be a minimum of 3/4” [19 cm] thick to

support the weight of the unit. For large units 48” [1.2m] and wider, a center structural element

inside the cabinet, under the platform, may be necessary.

GAS AND ELECTRICAL SUPPLY CLEARANCES

If not already in place, install a gas shut-off valve in an

easily accessible location for servicing of the rangetop.

Make sure all users of the rangetop know where this shut-

off is located, and how to shut off the gas. Any openings

in the wall or floor behind the appliance must be sealed.

The Installation Clearances on the following pages show

where the “G” and “E” zones should be located.

The rangetop is designed to be installed nearly

flush to the rear wall*. It may be necessary to

reposition the gas supply and power receptacle

/ junction box in order to accommodate the

rangetop when pushed back against the wall.

The power supply cord when plugged in, or

junction box should protrude no more than

2-1/2” [6.4 cm] from the rear wall.

* Unless installed in an island with no rear wall.

CABINETRY

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space

located above the surface units should be avoided. If cabinet storage is to be provided, the risk can

be reduced by installing the required vent hood that projects horizontally a minimum of 5” [12.7 cm]

beyond the bottom of the cabinets.

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

18” [45.7]

MIN.

12”

30.5

9-1/2”

24.1

28-1/2”

72.4

10”

25.4

2”

5.1

7-1/2” [19] MAX.

OPENING

HEIGHT

RECOMMENDED

GAS SHUT-OFF

VALVE LOCATION

FINISHED

FLOOR

VENT HOOD

MIN. CLEARANCE

TO NEAREST

COMBUSTIBLE

SIDE SURFACE

ELECTRICAL

SUPPLY

LOCATION

PLATFORM

28-3/16”

71.6

13” [33]

MAX.

37-1/8”

94.3

TO COOKING

SURFACE

28-1/2”

72.4

24-1/2” [62] MAX.

PLATFORM

7-1/2” [19] MAX.

OPENING

HEIGHT

LOW

BACKGUARD

APPLIANCE TOP

COOKING

SURFACE

COMBUSTIBLE

MATERIALS

COMBUSTIBLE

MATERIALS

INSTALLATION CLEARANCES WITH LOW BACKGUARD

FRONT VIEW

SIDE VIEW

NOTES:

* SHADED AREAS INDICATE WHERE COMBUSTIBLE MATERIALS ARE NOT ALLOWED.

* APPLIANCE TOP MUST BE LEVEL OR HIGHER THAN THE ADJACENT COUNTERTOP SURFACES.

* "G" IS GAS CONNECTION ZONE ON REAR WALL. MOUNT SHUT-OFF VALVE IN THIS ZONE

FOR EASY ACCESS WHEN RANGETOP IS INSTALLED.

* "E" IS ELECTRICAL SUPPLY ZONE.

* "W" IS APPLIANCE OPENING.

* "V" IS MIN. CLEARANCE TO REQUIRED VENTILATION HOOD OR COMBUSTIBLE SURFACE.

DIMENSIONS IN BRACKETS [ ] ARE IN CM.

LEVELING

The rangetop must be level, especially those models featuring a griddle. Raise to the desired height

by placing shims underneath the unit as needed.

The appliance top must

be level or higher than

the adjacent countertop

surfaces. Failure to adjust the height may expose

the adjacent cabinets to excessive heat which may

damage the cabinets or countertop.

CAUTION

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

9-1/2”

24.1

2”

5.1

12”

30.5

28-1/2”

72.4

10”

25.4

7-1/2” [19] MAX.

OPENING

HEIGHT

RECOMMENDED

GAS SHUT-OFF

VALVE LOCATION

ELECTRICAL

SUPPLY

LOCATION

FINISHED

FLOOR

MIN. CLEARANCE

TO NEAREST

COMBUSTIBLE

SIDE SURFACE

PLATFORM

12”

30.5

28-1/2”

72.4

24-1/2” [62] MAX.

PLATFORM

7-1/2” [19] MAX.

OPENING

HEIGHT

28-3/16”

71.6

37-1/8”

94.3

TO COOKING

SURFACE

ISLAND

TRIM

For Island Trim installations,

counter surface should

have a cantilever surface

meeting the rear of

the Island Trim

MIN. CLEARANCE

TO COMBUSTIBLE

SURFACES WITH

ISLAND TRIM

COOKING

SURFACE

APPLIANCE TOP

COMBUSTIBLE

MATERIALS

COMBUSTIBLE

MATERIALS

INSTALLATION CLEARANCES WITH ISLAND TRIM

FRONT VIEW

SIDE VIEW

NOTES:

* SHADED AREAS INDICATE WHERE COMBUSTIBLE MATERIALS ARE NOT ALLOWED.

* APPLIANCE TOP MUST BE LEVEL OR HIGHER THAN THE ADJACENT COUNTERTOP SURFACES.

* "G" IS GAS CONNECTION ZONE ON REAR WALL. MOUNT SHUT-OFF VALVE IN THIS ZONE

FOR EASY ACCESS WHEN RANGETOP IS INSTALLED.

* "E" IS ELECTRICAL SUPPLY ZONE.

* "W" IS APPLIANCE OPENING.

* "V" IS MIN. CLEARANCE TO REQUIRED VENTILATION HOOD OR COMBUSTIBLE SURFACE.

DIMENSIONS IN BRACKETS [ ] ARE IN CM.

FRONT COOLING VENTS

NOTICE

When placing your rangetop in the cabinet, DO

NOT BLOCK or obstruct the front cooling vents

shown. These vents allow air into the appliance

to keep the internal electronic parts cool.

COOLING

VENTS

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

BACKGUARD AND ACCESSORIES

Sheetmetal accessories such as the backguard, and areas at the rear of the rangetop may have sharp

edges. Wear work gloves while handling and installing these items.

BACKGUARD

Your Hestan rangetop is supplied at the factory with an Island Trim backguard. See Table 1 in the

APPENDIX section of this manual for other backguard options available from your Hestan dealer.

Selection of the appropriate backguard depends on the installation location and adjacent materials,

and the type of vent hood to be used. Installation instructions are included with the backguard kit.

A LOW OR TALL BACKGUARD IS REQUIRED WHEN INSTALLING THE RANGETOP AGAINST A

COMBUSTIBLE SURFACE - THE ISLAND TRIM IS NOT SUITABLE.

The top of the backguard serves as an exhaust vent to remove heat from under the rangetop. DO

NOT BLOCK or obstruct the top of the backguard. DO NOT touch the top of the backguard during

appliance operation as it may get hot. Allow sufficient time to cool before touching or cleaning this

area. DO NOT position plastic or other heat-sensitive items nearby which could melt or burn.

CAUTION

VENTILATION REQUIREMENTS

It is strongly recommended that this appliance be installed with a Hestan vent hood. Due to the high

heat output of this rangetop, it is very important that the hood and ductwork installation meets local

building codes and is installed by a qualified technician.

Do not use a down-draft style ventilation system.

Do not mount a microwave oven/ventilator combination above the rangetop. These type of units do

not have sufficient airflow to remove the high heat output of this rangetop and were not tested with

this type of appliance.

For non-Hestan approved vent hoods, the vent hood and/or blower unit must be rated for 1 CFM

[1.7 m³/hr] for every 100 BTU [.03 kW].

• If the rangetop has a 12” Griddle, add an additional 200 CFM [340 m³/hr] to the blower capacity.

For island applications, it is recommended to use a vent hood that is 6” [15.2 cm] wider than the

appliance, to allow for 3” [7.6 cm] of overlap on the left and right of the appliance.

Keep duct runs as short and straight as possible. Elbows and transition fittings reduce airflow

efficiency. Hestan recommends keeping the duct run under 50 ft. [15.2 m].

CONSULT WITH YOUR HESTAN DEALER ON SELECTING THE APPROPRIATE

VENT HOOD FOR YOUR HESTAN APPLIANCE.

ELECTRICAL CONNECTIONS

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Before turning

power ON, be sure all controls are in the OFF position. Failure to do so can

result in electrical shock or death.

ELECTRICAL GROUNDING

This appliance must be grounded. Grounding reduces the risk of electric

shock in the event of a short circuit. Grounding through the neutral conductor is prohibited for new

branch circuit installations (1996 NEC), mobile homes, and recreational vehicles, or in an area where

local codes prohibit it. Your Hestan rangetop is equipped with a 3-prong, grounding type plug which

must be plugged into a grounded, 3-prong 120V receptacle.

CAUTION

Improper grounding or reverse polarization will cause malfunctions in the

unit, such as continuous sparking of the igniters. This can damage the

appliance and create a shock hazard condition.

ELECTRICAL CONNECTION

The receptacle must be on its own dedicated circuit - 120 VAC, Single Phase, 60 Hz, with a current

rating of 15 Amps. If this is not available, a licensed electrician must install the appropriately

dedicated and grounded receptacle. The installation must be done in accordance with local codes,

or in the absence of local codes, it must be installed in accordance with the National Electrical Code,

ANSI/NFPA 70.

1. Make sure power is off at the supply panel / breaker.

2. Plug the appliance into the wall receptacle. Secure extra appliance cord out of the way so it

cannot be snagged on items under your rangetop.

3. Before restoring power at the supply panel / breaker, be sure all controls are in the OFF position.

GAS CONNECTION

GAS SUPPLY

The local gas authority or supplier should be consulted at the installation planning stage in order to

establish the availability of an adequate supply of gas (NG or LP). If it is a new installation, have the

gas authorities or supplier check the meter size and piping to assure that the unit is supplied with the

necessary amount of gas supply and pressure to operate the unit(s).

Gas connections should be made by a qualified plumber, or your professional appliance installer.

All appliances must be fitted with an accessible upstream gas shutoff valve as a means of isolating the

appliance for emergency shut off and for servicing.

Make certain new piping and connections have been made in a clean manner and have been purged

so that piping compound, chips, etc. will not clog regulators, valves, orifices, or burners. Use pipe

joint compound / thread sealant approved for natural and LP gases.

The appliance and its individual manual shutoff valve must be disconnected from the gas supply

piping system during any pressure testing of that system at test pressures in excess of 1/2 psi [3.5

kPa].

The appliance must be isolated from the gas supply piping system by closing its individual manual

shutoff valve during any pressure testing of that system at test pressures equal to or less than 1/2 psi

[3.5 kPa].

NEVER CONNECT THE APPLIANCE TO AN UNREGULATED GAS SUPPLY. Before proceeding,

ensure the appliance is fitted for Natural or Liquid Propane gas. Connecting to an improper gas type

will result in poor performance and increased risk of damage or injury. Gas type and gas consumption

(BTU per hour) for each burner type is shown on the rating label.

Installation of this cooking appliance must be made in accordance with local codes. In the absence of

local codes, this unit should be installed in accordance with the National Fuel Gas Code No.

Z223.1/

NFPA 54

, Natural Gas and Propane Installation code

CSA B149-1

, or Propane Storage and Handling

Code B149.2.

NOTE: See rating label for manifold pressure for the type of gas of your appliance.

The gas connection at the back of the rangetop (see below) features 1/2”NPT internal AND 3/4”NPT

external threads. Connect to gas supply using a minimum 3/4” inside diameter (1” OD) flexible

(semi–rigid) stainless steel gas hose with appropriate end fittings to prevent gas starvation. This

hose should be no more than 36” [91.4 cm] in length. Use the appropriate thread sealant on all

connections. Do not apply sealant to flare fittings. Use two wrenches when tightening the fittings.

The supply line must not interfere with the rear of the rangetop. Use caution when pushing the

rangetop against the back wall, so that you do not kink or crimp the flex hose as this could result in a

gas leak.

CONVERSION KITS

In the event your Hestan appliance needs to be converted from NG to LP, or vice-versa, you will

need to contact Hestan Customer Service to arrange a service call. This conversion should only be

performed by a qualified technician.

HIGH ALTITUDE KITS

If you live in a high altitude area, 2,000 ft. [610 m] or more above sea level, your appliance may

require different orifices for proper combustion and performance. You will need to contact Hestan

Customer Service to arrange a service call. High Altitude kits must be installed by a qualified

technician. Please have your model and serial number information ready when you call.

GAS CONNECTION - NATURAL GAS (NG)

To ensure proper heating performance of this appliance, verify that the gas line supply pressure is

adequate. The appliance is supplied with a gas pressure regulator already installed. This regulator is

set for a supply pressure of 7 inch WC [1.74 kPa] to maintain 5 inch WC [1.24 kPa] outlet (manifold)

pressure. Ensure that the service pipe supplying the appliance is fitted with a shut-off valve

conveniently positioned and easily accessible as an emergency gas shut-off.

GAS CONNECTION - LIQUID PROPANE (LP)

If you purchased an LP version of your appliance, it will be supplied with a gas pressure regulator

already installed. This regulator is set maintain 10 inch WC [2.49 kPa] outlet (manifold) pressure.

Ensure that the service pipe supplying the appliance is fitted with a shut-off valve conveniently

positioned and easily accessible as an emergency gas shut-off.

When connecting to LP gas, verify the tank is equipped with its own high pressure regulator. The

pressure of the gas supplied to the appliance must not exceed 11.0” WC [2.74 kPa].

GAS CONNECTION

1/2”NPT

INTERNAL

3/4”NPT

EXTERNAL

GAS CONNECTION

(CONTINUED)

LEAK TESTING

GENERAL

Although all gas connections on your Hestan appliance are leak tested at the factory prior to

shipment, a complete gas tightness check must be performed at the installation site due to possible

movement in shipment, or excessive pressure unknowingly being applied to parts of the unit.

Immediately check if the smell of gas is detected. Leak testing of the appliance shall be conducted

according to these instructions:

BEFORE TESTING

DO NOT SMOKE WHILE LEAK TESTING.

• Never leak test with an open flame.

• Make a soap solution of one part liquid detergent and one part water for leak testing purposes.

• Apply the solution to the gas fittings and flex hose by using a spray bottle or a brush.

TO TEST

• Make sure all control knobs are in the “OFF” position.

• Apply the soap solution to all fittings and flex hose.

• Turn the gas supply on.

• Check all connections from the supply line up to regulator connection at the rear of the

appliance.

• Soap bubbles will appear where a leak is present. If a leak is present, immediately turn off gas

supply, tighten any leaking fittings, turn the gas supply back on, and recheck.

• If you cannot stop a gas leak, turn off the gas supply and call the dealer where you purchased

your appliance.

• Do not use the appliance until all connections have been checked and do not leak.

FINAL SETUP

Remove any final packaging materials, and protective film from all exterior areas. Install any loose

items like sealed burner heads, cooking grates, etc. Ensure the sealed burner heads are properly

installed and seated on the burner base as shown below. There are notches on the burner base and

cross ring to help with alignment. The outer burner head features a long slot on the top of the head

which aligns with the spark igniter. Assembly of the single-flow burner head is similar.

BURNER

RING

BURNER

HEAD

BURNER

BASE

IGNITER

INNER

BURNER

HEAD

OUTER

BURNER

HEAD

BEAUTY

RING

CROSS

RING

BURNER

BASE

DUAL FLOW

BURNER

SINGLE FLOW

BURNER

FINAL SETUP

(CONTINUED)

Before testing operation of the appliance, verify the leak check was performed and the electrical

power has been restored to the unit. Turn the gas shut-off valve to the open position.

NOTICE

All the control knobs must be in the OFF position to prevent unintended operation at power up.

DO NOT ATTEMPT TO USE THE RANGETOP DURING A PROLONGED POWER FAILURE.

Verify ignition at each burner. Igniter will make a clicking sound until the flame lights within 4

seconds, then the clicking will stop. Check flame characteristics at each burner per the descriptions

below. Flames should be stable and not dance or lift off the burner ports. Flame may need to burn

for a few minutes to purge the gas lines of impurities. These appear as intermittent orange tips or

even tiny sparks in the flame. This is normal and the flame will eventually stabilize like those shown

in the image below.

If after a few minutes the flames continue to burn mostly yellow, verify that the burner head is

properly installed on the base, then retest. Use caution when handling the burner heads. They can

be very hot.

Turn down the control knob to the simmer setting to check function.

Check each burner individually, then check they operate satisfactorily with other burners on.

Light blue flame - Natural gas normal flame

Light blue flame with yellow tips - LP gas normal flame

Yellow flame - Needs adjustment

If after all the above tests still result in mostly yellow flames, or the burners do not light, contact

Hestan customer service to schedule a service call.

SERVICE

All warranty and non-warranty repairs should be performed by qualified service personnel. To

locate an authorized service agent in your area, contact your Hestan dealer, local representative, or

Hestan. Before you call, please have the model number and serial number information on hand.

Hestan Commercial Corporation

3375 E. La Palma Avenue

Anaheim, CA 92806

(888) 905-7463

APPENDIX

DÉFINITIONS DE SÉCURITÉ

CECI INDIQUE QUE L’INOBSERVATION DE CET

AVERTISSEMENT PEUT ENTRAÎNER DES BLESSURES GRAVES

VOIRE MORTELLES.

CECI INDIQUE QUE L’INOBSERVATION DE CET

AVERTISSEMENT PEUT ENTRAÎNER DES BLESSURES

MINEURES OU MODÉRÉES.

CECI INDIQUE QUE L’INOBSERVATION DE CET

AVERTISSEMENT PEUT ENTRAÎNER DES DOMMAGES DE

L’APPAREIL OU DES DÉGÂTS MATÉRIELS.

LISEZ ATTENTIVEMENT ET COMPLÈTEMENT CES INSTRUCTIONS

AVANT D’INSTALLER OU D’UTILISER VOTRE APPAREIL AFIN DE RÉDUIRE

LES RISQUES D’INCENDIE, DE BRÛLURE OU D’AUTRES BLESSURES.

CONSERVER CE MANUEL POUR RÉFÉRENCE FUTURE.

PRÉCAUTION

AVIS

INSTALLATEUR: LAISSER CE MANUEL AVEC LE PROPRIÉTAIRE DE L’APPAREIL.

PROPRIÉTAIRE: CONSERVEZ CE MANUEL POUR RÉFÉRENCE FUTURE.

Ne pas entreposer ou utiliser d’essence ou tout autre liquide ou gaz inflammable à proximité de

cet appareil ou de tout autre appareil.

EN PRÉSENCE D’UNE ODEUR DE GAZ:

1. Ne tenter d’allumer aucun appareil.

2. Ne toucher à aucun commutateur électrique.

3. N’utiliser aucun téléphone dans l’immeuble.

4. Appeler immédiatement le fournisseur de gazà partir d’un téléphone situé à l’extérieur

del’immeuble ; Suivre les instructions dufournisseur de gaz.

S’il est impossible de joindre le fournisseur degaz, appeler le service des incendies.

L ’installation et la réparation doivent être effectuées par un installateur ou une agence

deréparation ayant les qualifications requises oupar le fournisseur de gaz.

LE NON-RESPECT À LA LETTRE DE CES INSTRUCTIONS PEUT CAUSER

UN INCENDIE OU UNE EXPLOSION, QUI POURRAIT ENTRAÎNER DES

DOMMAGES MATÉRIELS, DES BLESSURES OU LA MORT.

1 PRÉCAUTIONS DE SÉCURITÉ - AVANT DE COMMENCER

2 NUMÉROS DE MODÈLE

3 PLAQUE SIGNALÉTIQUE

3 RESPECT DE LA RÉGLEMENTATION ET DES CODES EN VIGUEUR

3 EMPLACEMENT ET INSTALLATION / VENTILATION

7 DOSSERET ET ACCESSOIRES

8 BRANCHEMENTS ÉLECTRIQUES

8 RACCORDEMENT DE GAZ

10 PHASE FINALE DE L’INSTALLATION

11 SERVICE

12 APPENDICE

TABLE DES MATIÈRES

S’il est bien entretenu, cet appareil Hestan procurera un service sûr et fiable pendant de nombreuses

années. Lorsqu’on se sert de cet appareil, les pratiques élémentaires suivantes en matière de sécurité

doivent être adoptées.

IMPORTANT: Conservez ces instructions à l’intention de l’Inspecteur local des services du gaz ou de

l’électricité.

INSTALLATEUR: Veuillez laisser ces instructions d’installation au propriétaire.

PROPRIÉTAIRE: Veuillez conserver ces instructions d’installation pour référence future.

Cette table de cuisson N’EST PAS conçue pour être installée dans des maisons préfabriquées (mobiles)

ou dans des véhicules récréatifs. N’installez PAS cette table de cuisson à l’extérieur.

PRÉCAUTIONS DE SÉCURITÉ - AVANT DE COMMENCER

RISQUE DE CHOC ÉLECTRIQUE

Débranchez l’alimentation avant d’installer ou d’entretenir l’appareil. Avant de

le mettre sous tension, assurez-vous que toutes les commandes sont en position

«OFF». Ne pas le faire peut entraîner un choc électrique ou la mort.

MISE À LA TERRE ÉLECTRIQUE

Cet appareil doit être mis à la terre. La mise à la terre réduit le risque de

choc électrique en cas de court-circuit. Lisez la section BRANCHEMENTS

ÉLECTRIQUES de ce manuel pour des instructions complètes.

Cet appareil est pourvu d’une fiche à trois broches don’t une mise à la terre

assurant une protection contre les chocs électriques. La prise dans laaquelle elle est branchée doit être

correctement mise à la terre. Ne pas couper ni enlever la broche de mise à la terre de la fiche.

ALIMENTATION ÉLECTRIQUE

L’appareil doit avoir son propre circuit distinct - 120 VAC, monophasé, 60 Hz, avec une ampérage

nominale de 15 ampères. Demandez à l’installateur de vous montrer où se trouve le disjoncteur

électrique afin de savoir comment couper l’alimentation de cet appareil. Il incombe à l’utilisateur de

faire raccorder l’appareil par un électricien agréé conformément à tous les codes locaux, ou en l’absence

de ces codes, conformément au Code National de l’Électricité. Lisez la section BRANCHEMENTS

ÉLECTRIQUES du cet manuel pour tous le détails.

NUMÉROS DE MODÈLE

MODÈLES DES TABLES DE CUISSON

NO. MODÈLE DESCRIPTION

DISJONCTEUR

REQUIS

KRT365-NG / -LP TABLE DE CUISSON 36 po À 5 BRÛLEURS 15 Ampères

KRT364GD-NG / -LP TABLE DE CUISSON 36 po À 4 BRÛLEURS ET PLAQUE CHAUFFANTE 15 Ampères

KRT485GD-NG / -LP TABLE DE CUISSON 48 po À 5 BRÛLEURS ET PLAQUE CHAUFFANTE 15 Ampères

RESPECT DE LA RÉGLEMENTATION ET DES CODES EN

VIGUEUR

L’installation de cet appareil de cuisson doit être effectuée conformément aux codes locaux. En

l’absence de tels codes, installer cet appareil conformément au National Fuel Gas Code ANSI Z223.1/

NFPA 54, au code Natural Gas and Propane Installation CSA B149.1 ou au Propane Storage and

Handling Code B149.2. Tous les composants électriques doivent mis à la terre conformément aux codes

locaux ou, en l’absence de tels codes, au National Electrical Code ANSI/NFPA 70 ou au Code national de

l’électricité du Canada CSA C22.1.

COMMUNAUTÉ DU MASSACHUSETTS

Le Communauté du Massachusetts exige que toutes les installations au gaz soient effectuées par

un plombier ou monteur d’installations au gaz titulaire d’une autorisation appropriée délivrée par le

Massachusetts. Toutes les installations à demeure fonctionnant au propane ou au gaz naturel exigent la

pose d’un robinet manuel de gaz à poignée en T sur la conduite d’alimentation en gaz de l’appareil. Le

tuyau de raccordement flexible de gaz ne doit pas dépasser 36 po [91.4 cm].

PROPOSITION 65 DE CALIFORNIE – MISE EN GARDE

AVERTISSEMENT Ce produit peut vous exposer à des produits chimiques, y compris le

monoxyde de carbone, qui est reconnu dans l’État de Californie comme causant le cancer.

Pour plus d’informations, visitez www.P65Warnings.ca.gov.

PLAQUE SIGNALÉTIQUE

La plaque signalétique donne des informations importantes sur

cet appareil Hestan telles que les numéros de série et de modèle,

le type de gaz et la pression d’admission, les caractéristiques

électriques, la cote BTU pour chaque type de brûleur et les

dégagements minima d’installation.

La plaque signalétique se trouve sous l’unité.

Si un entretien est nécessaire, contactez le service clientèle de

Hestan avec les informations sur le modèle et le numéro de série

figurant sur la plaque.

DÉBALLAGE ET PLACEMENT

Retirez le carton extérieur et les matériaux d’emballage de la palette d’expédition. Ne retirez pas le

film plastique recouvrant les surfaces en acier inoxydable. Ce film protège la finition contre les rayures

jusqu’à ce que l’appareil soit installé dans sa position finale.

L’unité est peu lourde et doit être manipulée avec soin. Utilisez un équipement de sécurité approprié,

tel que des gants, et au moins 2 personnes pour mettre l’appareil en position pour éviter les blessures et

éviter d’endommager le sol ou l’appareil lui-même.

EMPLACEMENT ET INSTALLATION / VENTILATION

PLAQUE

SIGNALÉTIQUE

EMPLACEMENT ET INSTALLATION / VENTILATION

(SUITE)

PRÉPARATION

Avant de déplacer la table de cuisson, enlevez les grilles, les chapeaux de brûleurs et tout autre objet non

fixé.

La table de cuisson doit être montée sur une plate-forme stable, tel qu’illustré aux pages suivantes. La

plate-forme doit inclure une découpe de 6 po x 12 po [15,2 x 30,5 cm] à l’arrière gauche pour permettre les

connexions électriques et de gaz. La plate-forme doit également être de niveau pour garantir une surface

de cuisson uniforme, en particulier pour les modèles dotés d’une plaque chauffante. La plate-forme doit

avoir une épaisseur minimale de 3/4 po [19 cm] pour supporter le poids de l’unité. Pour les grandes unités

de 48 po [1,2m] et plus, un élément structurel central à l’intérieur du meuble, sous la plate-forme, peut

s’avérer nécessaire.

DÉGAGEMENTS DE GAZ ET D’APPROVISIONNEMENT ÉLECTRIQUE

Si ce n’est pas déjà fait, posez un robinet d’arrêt de gaz

dans un endroit facilement accessible pour l’entretien de la

table de cuisson. Assurez-vous que tous les utilisateurs de

l’appareil savent où se trouve cette fermeture et comment

couper le gaz. Toute ouverture dans le mur ou le plancher

derrière l’appareil doit être scellée. Les dégagements

d’installation sur les pages suivantes indiquent où les zones

« G » et « E » doivent être situées.

La table de cuisson est conçue pour être

installée près du mur arrière*. Il peut être

nécessaire de repositionner l’alimentation

en gaz et le réceptacle d’alimentation / boîte

de connexion afin d’accommoder la table de

cuisson lorsqu’elle est repoussée contre le mur.

Le cordon d’alimentation lorsqu’il est branché

ou la boîte de connexion ne doit pas dépasser

de plus de 2-1/2 po [6,4 cm] de la paroi arrière.

* Sauf si installé dans une île sans mur arrière.

ALIMENTATION

EN GAZ

VERS L'APPAREIL

ROBINET D’ARRÊT EN

POSITION OUVERTE

ARMOIRES

Pour éliminer le risque de brûlures ou d’incendie lorsqu’on se penche au-dessus des unités de surface

chauffées, il convient d’éviter d’utiliser l’espace de rangement offert par les armoires situés au-dessus des

unités de surface. Si on doit prévoir un espace de rangement, le risque peut être réduit en installant la

hotte d’évacuation requise de façon à ce qu’elle dépasse horizontalement d’au moins 5 po [12,7 cm] du

fond des armoires.

EMPLACEMENT ET INSTALLATION / VENTILATION

(SUITE)

18” [45.7]

MIN.

12”

30.5

9-1/2”

24.1

28-1/2”

72.4

10”

25.4

2”

5.1

7-1/2” [19] MAX.

HAUTEUR

D'OUVERTURE

EMPLACEMENT

RECOMMANDÉ DU

ROBINET D'ARRÊT

DE GAZ

PLANCHER

FINI

HOTTE DE VENTILATION

DÉGAGEMENT MIN. PAR

RAPPORT À LA SURFACE

LATÉRALE COMBUSTIBLE

LA PLUS PROCHE

ALIMENTATION

ÉLECTRIQUE

PLATE-FORME

28-3/16”

71.6

13” [33]

MAX.

37-1/8”

94.3

À LA SURFACE

DE CUISSON

28-1/2”

72.4

24-1/2” [62] MAX.

PLATE-FORME

7-1/2” [19] MAX.

HAUTEUR

D'OUVERTURE

DOSSERET BAS

HAUT DE

L'APPAREIL

SURFACE

DE CUISSON

MATÉRIAUX

COMBUSTIBLES

MATÉRIAUX

COMBUSTIBLES

VUE DE FACE

VUE DE CÔTÉ

REMARQUES:

* LES ZONES OMBRÉES INDIQUENT LES ENDROITS OÙ LES MATÉRIAUX COMBUSTIBLES SON PROHIBÉS.

* LE DESSUS DE L'APPAREIL DOIT ÊTRE AU MÉME NIVEAU OU PLUS HAUT QUE LES SURFACES DES PLANS DE TRAVAIL CONTIGUS.

* «G» INDIQUE LA ZONE DE RACCORDEMENT DE GAZ SUR LE MUR ARRIÈRE. MONTER LE ROBINET D'ARRÊT AUSSI HAUT QUE

POSSIBLE DANS CETTE ZONE POUR EN FACILITER L'ACCÈS QUAND LA TABLE DE CUISSON EST EN PLACE.

* «E» EST LA ZONE D'ALIMENTATION ÉLECTRIQUE.

* «W» INDIQUE L'OUVERTURE DESTINÉE À L'APPAREIL.

* «V» INDIQUE LE DÉGAGEMENT MIN. PAR RAPPORT À LA HOTTE DE VENTILATION REQUISE OU MATÉRIAUX COMBUSTIBLES.

DÉGAGEMENTS D'INSTALLATION AVEC DOSSERET BAS

LES DIMENSIONS ENTRE CROCHETS [ ] SONT EN CM.

NIVELLEMENT

La table de cuisson doit être de niveau, en particulier les modèles comportant une plaque chauffante.

Soulevez à la hauteur désirée en plaçant des cales sous l’unité au besoin.

Le dessus de

l’appareil doit

être au même

niveau ou plus haut que les surfaces des plans de

travail contigus. Le fait de ne pas ajuster la hauteur

peut exposer les armoires contigus à une chaleur

excessive qui pourrait endommager les armoires ou

le plan de travail.

PRÉCAUTION

La page charge ...

Hestan KRT364GDNG Guide d'installation

Marque: Hestan

Modèle: KRT364GDNG

Catégorie: Cuisinières

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Hestan KRT364GDNG Installation guide

Documents connexes

Autres documents

Fulgor Milano F6GRT364GS1 Guide d'installation