GE DPVH890EJMG Le manuel du propriétaire

Safety Instructions . . . . . . . . . . . 2–4
Operating Instructions
Controls  . . . . . . . . . . . . . . . . . . . . . . . . . . .5–8
Cycle Options  . . . . . . . . . . . . . . . . . . . .9, 10
Demand Response  . . . . . . . . . . . . . . . . .13
Dryer Features . . . . . . . . . . . . . . . . . .10, 11
Quick Start Guide  . . . . . . . . . . . . . . . . . . . .5
Settings Option  . . . . . . . . . . . . . . . . . . . . .10
Using the Dryer . . . . . . . . . . . . . . . . . . . . .12 
Installation Instructions
Before You Begin . . . . . . . . . . . . . . . .14, 15
Connecting the Inlet Hoses  . . . . . . . . .17
Connecting a Gas Dryer  . . . . . . . .18–21
Connecting an 
Electric Dryer  . . . . . . . . . . . . . . . . . . .22–24
Exhausting the Dryer  . . . . . . . . . . .25–31
Final Setup . . . . . . . . . . . . . . . . . . . . . . . . . .32
Installing the Pedestal  . . . . . . . . . .42–44
Location of your Dryer . . . . . . . . . .15, 16
Reversing the Door Swing  . . . . . .33–38
Stacking the Washer 
and Dryer . . . . . . . . . . . . . . . . . . . . . . .39–41
Troubleshooting Tips  . . . . . .45–48
Consumer Support
Consumer Support  . . . . . . . Back Cover
Warranty (Canada) . . . . . . . . . . . . . . . . . 50
Warranty (U.S.)  . . . . . . . . . . . . . . . . . . . . . 49
GEAppliances.com
Dryers
175D1807P632   49-90367    05-09 JR
Profile 
Write the model and serial 
numbers here:
Model # ______________
Serial #________________
They are on the label on the front
of the dryer behind the door.
Owner’s Manual &
Installation Instructions
Sécheuses
Profile
Secadoras
Profile 
Manuel d’utilisation 
et d’installation
Manual del propietario 
e instalación
La section française commence à la page 51
La sección en español empieza en la página 103
DPVH891
DPVH890
UPVH890
SAVE THESE INSTRUCTIONS

■ Properly ground dryer to conform with all

governing codes and ordinances. Follow details

in Installation Instructions.

■ Install or store where it will not be exposed to

temperatures below freezing or exposed to water

or weather.

■ Connect to a properly rated, protected and sized

power supply circuit to avoid electrical overload.

■ Remove all sharp packing items and dispose of

all shipping materials properly.

Exhaust/Ducting

Dryers MUST be exhausted to the outside to

prevent large amounts of moisture and lint from

being blown into the room.

Use only rigid metal 4″ diameter ductwork inside

the dryer cabinet. Use only rigid metal or flexible

metal 4-in diameter ductwork for exhausting to

the outdoors. Never use plastic or other

combustible, easy-to-puncture ductwork.

For complete details, follow the Installation

Instructions.

2

1

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk

of fire or explosion, electric shock, or to prevent property damage, personal injury,

or death.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light a match, or

cigarette, or turn on any gas or

electrical appliance.

Do not touch any electrical switch;

do not use any phone in your building.

Clear the room, building or area

of all occupants.

Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions carefully.

If you cannot reach your gas supplier,

call the fire department.

5

4

3

2

1

California Safe Drinking Water and Toxic Enforcement Act

This act requires the governor of California to publish a list of substances known to the state to cause cancer,

birth defects or other reproductive harm and requires businesses to warn customers of potential exposure to

such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be

minimized further by properly venting the dryer to the outdoors.

PROPER INSTALLATION

This dryer must be properly installed and located in accordance with the Installation Instructions

before it is used. Installation Instructions are included in the back of this manual.

■ Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

■ Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

2

Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips

3

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

WARNING!

YOUR LAUNDRY AREA

■ Keep the area underneath and around your

appliances free of combustible materials,

(lint, paper, rags, etc.), gasoline, chemicals

and other flammable vapors and liquids.

■ Keep the floor around your appliances clean

and dry to reduce the possibility of slipping.

■ Close supervision is necessary if this appliance is

used by or near children. Do not allow children to

play on, with or inside this or any other appliance.

■ Keep the area around the exhaust opening

and adjacent surrounding areas free from the

accumulation of lint, dust and dirt.

■ Keep all laundry aids (such as detergents,

bleaches, etc.) out of the reach of children,

preferably in a locked cabinet. Observe all

warnings on container labels to avoid injury.

■ Never climb on or stand on the dryer top.

WHEN USING YOUR DRYER

■ Never reach into the dryer while the drum is

moving. Before loading, unloading or adding

clothes, wait until the drum has completely

stopped.

■ Clean the lint filter before each load to prevent lint

accumulation inside the dryer or in the room. DO

NOT OPERATE THE DRYER WITHOUT THE LINT

FILTER IN PLACE.

■ Do not wash or dry articles that have been

cleaned in, washed in, soaked in or spotted

with combustible or explosive substances (such as

wax, oil, paint, gasoline, degreasers, dry-cleaning

solvents, kerosene, etc.). These substances give

off vapors that may ignite or explode. Do not add

these substances to the wash water. Do not use

or place these substances around your washer

or dryer during operation.

■ Do not place items exposed to cooking oils in

your dryer. Items contaminated with cooking oils

may contribute to a chemical reaction that could

cause a clothes load to catch fire.

■ Any article on which you have used a cleaning

solvent or that contains flammable materials

(such as cleaning cloths, mops, towels used in

beauty salons, restaurants or barber shops, etc.)

must not be placed in or near the dryer until

solvents or flammable materials have been

removed. There are many highly flammable items

used in homes such as acetone, denatured alcohol,

gasoline, kerosene, some household cleaners, some

spot removers, turpentines, waxes, wax removers

and products containing petroleum distillates.

■ The laundry process can reduce the flame

retardancy of fabrics. To avoid such a result,

carefully follow the garment manufacturer’s

care instructions.

■ Do not dry articles containing rubber, plastic

or similar materials such as padded bras, tennis

shoes, galoshes, bath mats, rugs, bibs, baby pants,

plastic bags, pillows, etc. that may melt or burn.

Some rubber materials, when heated, can under

certain circumstances produce fire by spontaneous

combustion.

■ Do not store plastic, paper or clothing that may

burn or melt on top of the dryer during operation.

■ Garments labeled Dry Away from Heat or Do Not

Tumble Dry (such as life jackets containing Kapok)

must not be put in your dryer.

■ Do not dry fiberglass articles in your dryer.

Skin irritation could result from the remaining

particles that may be picked up by clothing

during subsequent dryer uses.

■ To minimize the possibility of electric shock, unplug

this appliance from the power supply or disconnect

the dryer at the household distribution panel by

removing the fuse or switching off the circuit

breaker before attempting any maintenance or

cleaning (except the removal and cleaning of the

lint filter). NOTE: Pressing START/PAUSE or POWER

does NOT disconnect the appliance from the power

supply.

■ If you see water on the floor around the dryer,

call for service.

GEAppliances.com

WHEN NOT USING YOUR DRYER

■ Grasp the plug firmly when disconnecting this

appliance to avoid damage to the cord while

pulling. Place the cord away from traffic areas

so it will not be stepped on, tripped over or

subjected to damage.

■ Do not attempt to repair or replace any part of

this appliance or attempt any servicing unless

specifically recommended in this Owner’s Manual

or in published user-repair instructions that you

understand and have the skills to carry out.

■ Before discarding a dryer, or removing it from

service, remove the dryer door to prevent children

from hiding inside.

■ Do not tamper with controls.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

4

WARNING!

WHEN USING YOUR DRYER (cont.)

■ Never attempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled,

or has missing or broken parts, including a

damaged cord or plug.

■ The interior of the machine and the exhaust duct

connection inside the dryer should be cleaned at

least once a year by a qualified technician. See

the Sorting and Loading Hints section on page 12.

■ If yours is a gas dryer, it is equipped with an

automatic electric ignition and does not have

a pilot light. DO NOT ATTEMPT TO LIGHT WITH

A MATCH. Burns may result from having your hand

in the vicinity of the burner when the automatic

ignition turns on.

■ Do not open the dryer door during steam cycles.

The steam is very hot and it will continue to

exhaust from the port for several seconds after

opening. Do not touch the steam port after a

steam cycle.

■ Do not use a steam cycle with items such

as wool, leather, silk, lingerie, foam products

or electric blankets.

■ Do not use steam cycles on new clothes without

first washing.

■ You may wish to soften your laundered fabrics

or reduce the static electricity in them by using

a dryer-applied fabric softener or an anti-static

conditioner. We recommend you use either

a fabric softener in the wash cycle, according

to the manufacturer’s instructions for those

products, or try a dryer-added product for which

the manufacturer gives written assurance on

the package that their product can be safely

used in your dryer. Service or performance

problems caused by use of these products are

the responsibility of the manufacturers of those

products and are not covered under the warranty

of this appliance.

■ Never attempt to use the Steam Dewrinkle or

Steam Refresh cycles without clothes in the drum.

Additionally, it is highly recommended to select

the appropriate load size for best results. Selecting

large load cycles for small loads may result in

wetting of clothes, and selecting small load cycles

for large loads may result in poor dewrinkling

performance.

Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING! To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT

SAFETY INSTRUCTIONS before operating this appliance.

About the dryer control panel.

GEAppliances.com

Throughout this manual, features and appearance may vary from your model.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

1

49 8

5

7

6

3

2

Quick Start

If the screen is dark, press the POWER button to “wake up”

the display.

Press the

POWER

button.

Select a cycle by turning the

Cycle Knob.

If you selected a SENSOR CYCLE – just

press the START/PAUSE button.

If you selected a TIMED DRY CYCLE –

select your heat setting and the

amount of time you want your items

to dry by using the cursor buttons.

Then press the START/PAUSE button.

3

2

1

5

Power

Press to “wake up” the display. If the display is active, press to turn the dryer off.

NOTE: Pressing POWER does not disconnect the appliance from the power supply.

1

2

About the dryer control panel.

Dry Cycles

The dry cycle controls the cycle time for the drying process. The chart below will help you match

the dry setting with the loads.

Sensor Cycles

COTTONS For cottons and most linens.

NORMAL/ For loads consisting of cottons and poly-blends.

MIXED LOAD

WRINKLE FREE For wrinkle-free/easy care and permanent press items.

ACTIVE WEAR Clothing worn for active sports exercise and some casual wear. Fabrics include new

technology finishes and stretch fibers such as Spandex.

DELICATES For lingerie and special-care fabrics.

SPEED DRY For small loads that are needed in a hurry, such as sports or school uniforms. Can also be

used if the previous cycle left some items damp, such as collars or waistbands.

Timed Dry Cycles

STEAM For slightly wrinkled dry garments. Significantly reduces wrinkles on 1–5 garments.

REFRESH Selecting a higher number of garments for the cycle (e.g., selecting 5-garment load

for a 1-garment load) may result in excessive wetting of clothes. After the SteamRefresh

Cycle, the unit will beep and display “Garments Ready” and “0:00.” If the unit is not turned

off or if the door is not opened, the dryer will continue to tumble for 30 minutes. At the end

of 30 minutes, it will display “0:00” and “Cycle Complete.”

A single extremely light fabric item may need to have an additional item included

in the steam refresh cycle to achieve optimum results.

STEAM For use with larger loads than STEAM REFRESH. Ideal for loads left in dryer for an extended

DEWRINKLE time. Selecting a larger cycle than needed (e.g., selecting Large Load for a half-full dryer)

may result in excessive wetting of clothes.

WARM UP Provides 10 minutes of warming time to warm up clothes.

My Cycle (on some models)

MY CYCLE Press to use, create or modify custom dry cycles.

Timed Dry

Use to set your own dry time. TIMED DRY is also recommended for small loads.

To use TIMED DRY:

1. Turn dry cycle dial to TIMED DRY.

2. Select the drying time by pressing the ▲ and ▼ buttons. You can increase the time in 10-minute

increments up to 2

1

⁄2 hours.

3. Select the DRY TEMP.

4. Close the door.

5. Press START/PAUSE.

Sensor Dry Level

The sensor continuously monitors the amount of moisture in the load. When the moisture in your

clothes reaches your selected dry level, the dryer will stop.

EXTRA DRY Use for heavy-duty fabrics or items that should be very dry, such as towels.

MORE DRY Use for heavy or mixed type of fabrics.

DRY Use for normal dryness level suitable for most loads. This is the preferred cycle

for energy saving.

LESS DRY Use for lighter fabric (ideal for ironing).

DAMP For leaving items partially damp.

3

4

6

Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips

7

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

GEAppliances.com

Dry Temp

You can change the temperature of your dry cycle.

ANTI-BACTERIAL This option may only be used with COTTONS or MIXED LOAD cycles. This option reduces

certain types of bacteria by 99.9%, including: Staphylococcus aureus, Pseudomonas

aeruginosa and Klebsiella pneumoniae*. The anti-bacterial process occurs when high

heat is used during a portion of this drying cycle.

NOTE: Do not use this cycle on delicate fabrics.

* The Anti-Bacterial Cycle is Certified by NSF International (formerly National Sanitation

Foundation) to NSF Protocol P154 Sanitization Performance of Residential Clothes Dryers.

HIGH For regular to heavy cottons.

MEDIUM For synthetics, blends and items labeled permanent press.

LOW For delicates, synthetics and items labeled Tumble Dry Low.

EXTRA LOW For lingerie and special-care fabrics.

START/PAUSE

Press to start a dry cycle. If the dryer is running, press it once and it will pause the dryer.

Press it again to restart the dry cycle.

My Cycle (on some models)

Set up your favorite combination of settings and save them here for one touch recall.

These custom settings can be set while a cycle is in progress.

To store a MY CYCLE combination of settings:

1. Select your drying cycle.

2. Change DRY TEMP and SENSOR DRY LEVEL settings to fit your needs.

3. Select any drying OPTIONS you want.

4. Press and hold the MY CYCLE button for 3 seconds to store your selection. A beep will sound

and the button will light up.

To recall your stored MY CYCLE combination:

Press the MY CYCLE button before drying a load. The light around the button will light up when

MY CYCLE is selected.

To change your stored MY CYCLE combination:

Follow Steps 1–4 in “To store a MY CYCLE combination of settings.”

Display

“CLEAN LINT FILTER” (message)

This message stays on for 15 minutes after the cycle finishes. This message is only a reminder.

5

6

8

Special Cycle Status OR

Dryer Rack OR Timed Dry

Est. Cycle Time

OR Time to Dry

Delay Time

Status

Lint Filter Status

Screen

7

DELAY TIME

Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips

8

About the dryer control panel.

Specialty Cycles

1. Turn the CYCLE knob to SPECIAL CYCLES. A list of cycle options will appear in the display.

2. Using the cursor buttons, select a CATEGORY.

3. Using the cursor buttons, select a CYCLE.

Press the BACK button to take you back to the CATEGORIES.

4. Press ENTER to select.

5. Press the START/PAUSE button.

SPECIALTY CYCLES include:

Garments

■ Coats

■ Hosiery/Bras (use mesh bag)

■ Jeans

■ Khakis

Bed and Bath

■ Blankets (Cotton)

■ Comforters

■ Sheets

■ Towels

Other Specialty

■ Air Fluff

■ Dryel

■ Fleece

■ Fragile Cotton

■ Performance Fabrics

■ Pet Bedding

■ Play Clothes

■ Sleeping Bags

■ Rack Dry

■ Throw Rugs

9

Washer Communicated Cycles

To turn on communication, press the

SETTINGS button on the washer control

panel. When “DRYER LINK” appears in the

display, press ENTER. Using the arrow keys,

select ON; then press ENTER.

When the washer cycle is completed, the

washer will communicate with the dryer

when any button on the control panel is

touched or the door is opened.

The washer will display, “TRANSFERRING

CYCLE INFORMATION TO THE DRYER” and

the dryer will display, “RECEIVING CYCLE

INFORMATION TO THE DRYER”.

The dryer will only communicate with the

washer if the dryer is not running a cycle.

If the washer starts a new cycle before the

dryer has a chance to communicate with

it, the information will be lost.

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions

About cycle options.

NOTE: Not all features are available on all dryer models. GEAppliances.com

Extend Tumble

Minimizes wrinkles by adding approximately

60 minutes of no-heat tumbling after clothes

are dry.

The light around the button will light up when

EXTEND TUMBLE is on.

Extend Tumble is automatically selected

for the SteamRefresh cycle and cannot

be deselected. Dryer will beep and display

“Garments Ready” when SteamRefresh is

complete. The dryer will continue in Extend

Tumble until the door is opened.

Damp Alert

This option causes the dryer to beep when

clothes have dried to a damp level. Remove

items that you wish to hang dry. The DAMP

ALERT will only beep when this option is

selected.

Removing clothes and hanging them when

they are damp can reduce the need to iron

some items.

The light around the button will light up when

DAMP ALERT is on.

Drum Light

Press this button to turn on the light in the

dryer.

Press the button again to turn the light off.

This only controls the light when the door

is shut. NOTE: The light will turn off by itself

after one minute when the door is shut.

When the door is opened, the light comes

on automatically.

The light around the button will light up when

DRUM LIGHT is on.

Delay Start

Use to delay the start of your dryer.

1. Choose your dry cycle and any options.

2. Press DELAY START. You can change the

delay time in 1/2-hour increments, using

the ▲ or ▼ arrow pads.

3. Press the START/PAUSE button to start

the countdown.

The countdown time will be shown in the

ESTIMATED TIME REMAINING display.

NOTES:

■ If the door is opened while the dryer is

in DELAY, the countdown time will not

restart unless the door is closed and

START/PAUSE button has been pressed

again.

■ You can delay the start of a dry cycle up

to 24 hours.

The light around the button will light up when

DELAY START is on.

Lock

You can lock the controls to prevent any

selections from being made. Or you can lock

the controls after you have started a cycle.

Children cannot accidentally start the dryer

by touching pads with this option selected.

To lock the dryer, press the LOCK button.

To unlock the dryer, press and hold the LOCK

button for 3 seconds.

The light around the LOCK button will light up

when the controls are locked.

Even though the controls are locked, the

POWER button is still active in case you have

to turn the unit off.

Press to lock control.

Hold 3 seconds to unlock.

9

Settings

Under the SETTINGS option, you can

adjust the volume or the brightness of

the display.

VOLUME

■ End of Cycle (signal) volume can be set

from HIGH, MED, LOW or OFF.

■ Control Sounds volume can be set from

HIGH, MED, LOW or OFF.

DISPLAY BRIGHTNESS can be set from

HIGH, MED or LOW.

After you have made your selection,

press ENTER.

10

Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips

About dryer features.

Built-In Rack Dry System

A handy drying rack may be used for drying items such as tennis shoes.

Place items flat on the drying rack and block such items as wool sweaters

and delicate fabrics. Dry with low heat.

To install the Built-In Rack Dry System

1. Make sure the drum of the dryer is oriented so the rack drying system is

on the left side of the dryer.

2. Pull the drying rack screen out from the left side and engage the handle

“posts” in the opposite baffle slots.

3. Place the garment on the rack and close the door.

4. Press the DRYER RACK button.

5. Select desired TIME.

6. Press the START/PAUSE button.

NOTE:

■ Do not use this drying rack when there are other clothes in the dryer.

■ Make sure to detach the drying rack at the end of the cycle and fully

retract the screen back into the baffle.

Drum Lamp

Before replacing the light bulb, be sure to unplug the dryer power cord or

disconnect the dryer at the household distribution panel by removing the

fuse or switching off the circuit breaker. Reach above dryer

opening from

inside the drum. Remove the

bulb and replace with the same size bulb.

About cycle options.

NOTE: Not all features are available on all dryer models.

Engage the handle posts

11

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

GEAppliances.com

To Use the Built-In Hook

for Hanging Garments

1. Make sure the drum of the dryer is

oriented so the hook is on the top

center of the dryer.

2. Using your finger, pull the hook out

of the baffle.

3. Hang the garment on a hanger,

hang the hanger on the hook and

close the door.

4. Press the DRYER RACK button.

5. Select the desired time.

6. Press the START/PAUSE button.

Reverse Tumble

™

All Profile front-load matching dryers are equipped with the Reverse Tumble

™

feature, as part of the Duo Dry Plus system

™

. By reversing the direction

of drum rotation during the drying cycle, your dryer will tangle the clothes

load less, dry more evenly and improve drying times. Typical loads such

as bed and bath mixed loads, where sheets, towels and pillow cases are

laundered together, benefit from this capability. When the dryer reverses

direction, there will be a slight pause and sound change. This is normal.

All dryer cycles utilize this feature, except when the rack dry option is selected,

in which case the drum does not tumble.

12

Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips

Using the dryer.

Care and Cleaning of the Dryer

Dryer Interior and Duct: The interior of

the appliance and exhaust duct should be

cleaned once a year by qualified service

personnel.

The Exterior: Wipe or dust any spills or

washing compounds with a damp cloth.

Dryer control panel and finishes may be

damaged by some laundry pretreatment

soil and stain remover products. Apply

these products away from the dryer. The

fabric may then be washed and dried

normally. Damage to your dryer caused

by these products is not covered by your

warranty.

Do not touch the surface or the display

with sharp objects.

The Lint Filter: Clean the lint filter before

each use. Remove by pulling straight up.

Run your fingers across the filter. A waxy

buildup may form on the lint filter from

using dryer-added fabric softener sheets.

To remove this buildup, wash the lint

screen in warm, soapy water. Dry

thoroughly and replace. Do not operate

the dryer without the lint filter in place.

Vacuum the lint from the dryer lint

filter if you notice a change in dryer

performance.

Stainless Steel: To clean stainless steel

surfaces, use a damp cloth with a mild,

nonabrasive cleaner suitable for stainless

steel surfaces. Remove the cleaner

residue, and then dry with a clean cloth.

The stainless steel used to make

the dryer drum provides the highest

reliability available in a GE dryer. If

the dryer drum should be scratched or

dented during normal use, the drum

will not rust or corrode. These surface

blemishes will not affect the function

or durability of the drum.

The Exhaust Hood: Check with a mirror

that the inside flaps of the hood move

freely when operating. Make sure that

there is no wildlife (birds, insects, etc.)

nesting inside the duct or hood.

Always follow fabric manufacturer’s care label when laundering.

Tumble

dry

Dry

Normal

Permanent Press/

wrinkle resistant

Gentle/

delicate

Do not tumble dry

Do not dry

(used with

do not wash)

Heat

setting

High

Medium

Low

No heat/air

Special

instructions

Line dry/

hang to dry

Drip dry

Dry flat

In the shade

Dry Labels

Sorting and Loading Hints

As a general rule, if clothes are sorted

properly for the washer, they are sorted

properly for the dryer. Try also to sort items

according to size. For example, do not dry

a sheet with socks or other small items.

Do not add fabric softener sheets once

the load has become warm. They may

cause fabric softener stains. Bounce

®

Fabric Conditioner Dryer Sheets have

been approved for use in this dryer when

used in accordance with the manufacturer’s

instructions.

See below for lint filter cleaning instructions.

Do not overload. This wastes energy and

causes wrinkling.

Do not dry the following items: fiberglass

items, woolens, rubber-coated items, plastics,

items with plastic trim and foam-filled items.

Fabric Care Labels

Below are fabric care label “symbols” that

affect the clothing you will be laundering.

Model DPVH891 is compatible with the GE Demand Response

(DR) module which can be purchased separately. Contact your

local utility or visit www.GEAppliances.com/demand_response

to see if your area is using DR technology.

The following demand response features are available as part

of a pilot test program with the local utility company to help

consumers reduce peak electricity usage in the home.

Installation

The preferred location for the module installation is on top

of the clothes dryer.

Details on how to connect the cables to the module are

in the instructions that come with the module.

Wait 5 minutes; then press the Settings button. Scroll and

look for the energy management screen as seen below.

This screen means the module is attached correctly and

you can begin to use your DR-enabled appliance following

the instructions below.

If the Energy Management Screen is not available, refer to

the DR module troubleshooting guide.

Quick Guide

There are 4 power levels available: Critical, High, Medium and

Low. On the Medium and Low levels, the unit runs as normal.

The following steps show how the unit reacts during startup

at Critical and High power levels.

Option 1 (Delay Eco)

During startups at Critical and High levels, the unit will delay

starting until the level becomes Medium or Low. Press the

START/PAUSE button.

Option 2 (Override Delay Eco)

To start the unit when Delay Eco is shown, press the DELAY

START button to turn the delay off. Then press START/PAUSE

to begin the cycle.

Settings Menu

Press SETTINGS; then select Energy Management.

Delay Eco Override

If you are starting a cycle in a Critical or High utility rate, this

option allows the unit to automatically run on an Eco Cycle. This

setting will operate with less energy than normal cycles. Default

setting is YES.

Auto-Extend Delays

If a timed delay is selected, this option allows for the scheduled

start to extend if the utility rate is Critical or High at the

scheduled start. The default setting will automatically extend

these cycles.

Timed Dry Eco Option

If the unit is running in Timed Dry Mode and the utility rate

switches to Critical or High, the unit will conserve energy by

decreasing heat if YES (default) is selected. If NO is selected, the

unit will operate normally.

NOTE: When YES (default) is selected, your load may be damp

at the end of the cycle.

In order for the demand response features on the appliance to

work, additional equipment is required to be installed to interface

with the local utility. Such equipment may be sold separately

and/or is available through your utility as part of the pilot test

program. Check with your utility company to see if a pilot test

program is available in your area and for full details.

PLEASE NOTE

: At the conclusion of the pilot test program or if

you move to an area where the program is not available, the

demand response features cannot be activated and utilized on

the appliance. The appliance will function as normal after the

demand response equipment has been deactivated or

disconnected.

S

ETTINGS

D

ELAY

S

TAR T

D

RYER

R

ACK

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

13

Demand Response. (on some models) GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for local

electrical inspector’s use.

•

IMPORTANT – Observe all governing codes and

ordinances.

• Install the clothes dryer according to the manufacturer’s

instructions and local codes.

• Note to Installer – Be sure to leave these instructions

with the Consumer.

• Note to Consumer – Keep these instructions for future

reference.

• Clothes dryer installation must be performed by a

qualified installer.

• This dryer must be exhausted to the outdoors.

• Before the old dryer is removed from service or

discarded, remove the dryer door.

• Service information and the wiring diagram are located

in the control console.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the appliance

is used near children.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty

.

• Install the dryer where the temperature is above 50°F

for satisfactory operation of the dryer control system.

• Remove and discard existing plastic or metal foil duct

and replace with UL-listed duct.

Installation Dryer

Instructions

DPVH891, DPVH890, UPVH890

14

Questions? Call 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

FOR YOUR SAFETY:

WARNING –

Risk of Fire

• To reduce the risk of severe injury or death, follow

all installation instructions.

• Clothes dryer installation must be performed by a

qualified installer.

• Install the clothes dryer according to these

instructions and in accordance with local codes.

• This dryer must be exhausted to the outdoors.

• Use only 4

″

rigid metal ducting for exhausting the

clothes dryer to the outdoors.

• DO NOT install a clothes dryer with flexible plastic

ducting materials. If flexible metal (semi-rigid or

foil-type) duct is installed, it must be UL-listed and

installed in accordance with the instructions found

in “Connecting the Dryer to House Vent” on page 26

of this manual. Flexible ducting materials are known

to collapse, be easily crushed and trap lint. These

conditions will obstruct dryer airflow and increase

the risk of fire.

• Do not install or store this appliance in any location

where it could be exposed to water and/or weather.

• Save these instructions. (Installers: Be sure to leave

these instructions with the customer.)

FOR GAS MODELS ONLY:

NOTE: Installation and service of this dryer must be

performed by a qualified installer, service agency or

the gas supplier.

In the Commonwealth of Massachusetts:

• This product must be installed by a licensed

plumber or gas fitter.

• When using ball-type gas shut-off valves, they

shall be T-handle-type.

• A flexible gas connector, when used, must not

exceed 3 feet.

CALIFORNIA SAFE DRINKING WATER AND

TOXIC ENFORCEMENT ACT

This act requires the governor of California to publish a

list of substances known to the state to cause cancer,

birth defects or other reproductive harm and requires

businesses to warn customers of potential exposure to

such substances. Gas appliances can cause minor

exposure to four of these substances, namely benzene,

carbon monoxide, formaldehyde and soot, caused

primarily by the incomplete combustion of natural gas

or LP fuels. Properly adjusted dryers will minimize

incomplete combustion. Exposure to these substances

can be minimized further by properly venting the dryer

to the outdoors.

Installation Instructions

15

UNPACKING YOUR DRYER

Tilt the dryer sideways and remove the foam

shipping pads by pulling at the sides and breaking

them away from the dryer legs. Be sure to remove

all of the foam pieces around the legs.

Remove the bag containing the literature and serial

cable.

DRYER DIMENSIONS

51″

(129.5 cm)

39.1″

(993 cm)

32.34″

(847 cm)

27″

(68.6 cm)

39.1″

(993 cm)

27″

(68.6 cm)

39.5″

(100.3 cm)

33.5″

(85.1 cm)

39.5″

(100.3 cm)

Side View

Front View

LOCATION OF YOUR DRYER

MINIMUM CLEARANCE OTHER THAN

ALCOVE OR CLOSET INSTALLATION

Minimum clearance to combustible surfaces and

for air openings are:

• 0 inch clearance both sides

• 1 inch front

• 3 inches rear

Consideration must be given to provide adequate

clearance for proper operation and service.

53″

(134.6 cm)

16

Installation Instructions

REQUIREMENTS FOR ALCOVE OR

CLOSET INSTALLATION

• Your dryer is approved for installation in

an alcove or closet, as stated on a label on

the dryer back.

• The dryer MUST be vented to the outdoors. See

the EXHAUSTING THE DRYER section.

• Minimum clearance between dryer cabinet and

adjacent walls or other surfaces is:

0″ either side

3″ front and rear

• Minimum vertical space from floor to overhead

shelves, cabinets, ceilings, etc., is 52″.

• Closet doors must be louvered or otherwise

ventilated and have at least 60 square inches

of open area equally distributed. If the closet

contains both a washer and a dryer, doors must

contain a minimum of 120 square inches of open

area equally distributed.

• The closet should be vented to the outdoors

to prevent gas pocketing in case of gas in the

supply line.

• No other fuel-burning appliance shall be

installed in the same closet with the dryer

(gas models only).

NOTE: WHEN THE EXHAUST DUCT IS LOCATED AT

THE REAR OF THE DRYER, MINIMUM CLEARANCE

FROM THE WALL IS 5.5 INCHES.

BATHROOM OR BEDROOM

INSTALLATION

• The dryer MUST be vented to the outdoors. See

EXHAUSTING THE DRYER.

• The installation must conform with local codes or,

in the absence of local codes, with the NATIONAL

ELECTRICAL CODE, ANSI/NFPA NO. 70 (for electric

dryers) or NATIONAL FUEL GAS CODE, ANSI Z223

(for gas dryers).

MOBILE OR MANUFACTURED HOME

INSTALLATION

• The installation must conform to the

MANUFACTURED HOME CONSTRUCTION & SAFETY

STANDARD, TITLE 24, PART 32–80 or, when such

standard is not applicable, with AMERICAN

NATIONAL STANDARD FOR MOBILE HOME,

NO. 501B.

• The dryer MUST be vented to the outdoors with

the termination securely fastened to the mobile

home structure. (See EXHAUSTING THE DRYER.)

• The vent MUST NOT be terminated beneath a

mobile or manufactured home.

• The vent duct material MUST BE METAL.

• FOR GAS MODELS ONLY: KIT 14-D346-33 MUST be

used to attach the dryer securely to the structure.

• FOR GAS MODELS ONLY: The vent MUST NOT be

connected to any other duct, vent or chimney.

• Do not use sheet metal screws or other

refastening devices which extend into the interior

of the exhaust vent.

• Provide an opening with a free area of at least

25 sq. in. for introduction of outside air into the

dryer room.

17

Installation Instructions

CONNECTING INLET HOSES

To produce steam, the dryer must connect to

the cold water supply. Since the washer must

also connect to the cold water, a “Y” connector

is inserted to allow both inlet hoses to make that

connection at the same time.

NOTE: Use the new inlet hoses provided; never

use old hoses.

1. Turn the cold water faucet off. Remove the

washer inlet hose from the washer fill valve

connector (cold).

2. Ensure the rubber flat washer is in place and

screw the female coupling of the short hose

onto the washer fill valve connector. Tighten

by hand until firmly seated.

3. Attach the female end of the ‘’Y’’ connector

to the male coupling of the short hose. Ensure

the rubber flat washer is in place. Tighten

by hand until firmly seated.

4. Insert the filter screen in the coupling of the

washer’s inlet hose. If a rubber flat washer

is already in place remove it before installing

the filter screen. Attach this coupling to one male

end of the ‘’Y’’ connector. Tighten by hand until

firmly seated.

5. Ensure the rubber flat washer is in place and

attach the dryer’s long inlet hose to the other

male end of the ‘’Y’’ connector. Tighten by hand

until firmly seated.

6. Ensure the rubber flat washer is in place and

attach the other end of the dryer’s long inlet

hose to the fill valve connector at the bottom

of the dryer back panel. Tighten by hand until

firmly seated.

CONNECTING INLET HOSES (cont.)

7. Using pliers, tighten all the couplings with

an additional two–thirds turn.

NOTE: Do not overtighten. Damage to the couplings

may result.

8. Turn the water faucet on.

9. Check for leaks around the ‘’Y’’ connector,

faucet and hose couplings.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed

within 42 in. (107 cm) of your washer’s water inlet.

The faucets MUST be 3/4 in. (1.9 cm) garden

hose-type so inlet hoses can be connected. Water

pressure MUST be between 10 and 120 pounds

per square inch. Your water department can

advise you of your water pressure.

NOTE: A water softener is recommended to reduce

buildup of scale inside the steam generator

if the home water supply is very hard.

❒ 10″ Adjustable

wrenches (2)

❒ 8″ Pipe wrench

❒ Slip-joint pliers

❒ Flat-blade screwdriver

❒ Level

18

Installation Instructions

TOOLS YOU WILL NEED

CONNECTING A GAS DRYER (skip for electric dryers)

FOR YOUR SAFETY:

WARNING

Before beginning the installation, turn off

the circuit breaker(s) or remove the dryer’s circuit

fuse(s) at the electrical box. Be sure the dryer cord

is unplugged from the wall.

Turn the dryer’s gas shut-off valve in the supply

line to the OFF position.

Disconnect and discard old flexible gas connector

and ducting material.

Shut-off

Valve

MATERIALS YOU WILL NEED

❒ 4″ dia. metal elbow

❒ Pipe compound

❒ Flexible gas line

connector

❒ Duct clamps (2) or

Spring clamps (2)

❒ Safety glasses

❒ 4″ dia. metal duct

(recommended)

❒ 4″ dia., UL-listed flexible

metal duct (if needed)

❒ Gloves

❒ Soap solution for

leak detection

❒ Exhaust hood

❒ Duct tape

19

Installation Instructions

GAS REQUIREMENTS

WARNING

• Installation must conform to local codes

and ordinances, or in their absence, the

NATIONAL FUEL GAS CODE, ANSI Z223.

• This gas dryer is equipped with a Valve and

Burner Assembly for use only with natural gas.

Using conversion kit 14-A048, your local service

organization can convert this dryer for use with

propane (LP) gas. ALL CONVERSIONS MUST BE

MADE BY PROPERLY TRAINED AND QUALIFIED

PERSONNEL AND IN ACCORDANCE WITH LOCAL

CODES AND ORDINANCE REQUIREMENTS.

• The dryer must be disconnected from the gas

supply piping system during any pressure testing

of that system at a test pressure in excess of

0.5 PSI (3.4 KPa).

• The dryer must be isolated from the gas supply

piping system by closing the equipment shut-off

valve during any pressure testing of the gas

supply piping of test pressure equal to or less

than 0.5 PSI (3.4KPa).

DRYER GAS SUPPLY CONNECTION

3/8″ NPT MALE THREAD GAS SUPPLY

NOTE: Add to vertical

dimension the distance between

cabinet bottom to floor.

GAS SUPPLY

• A 1/8″ National Pipe Taper thread plugged

tapping, accessible for test gauge connection,

must be installed immediately upstream of the

gas supply connection to the dryer. Contact your

local gas utility should you have questions on the

installation of the plugged tapping.

• Supply line is to be 1/2″ rigid pipe and equipped

with an accessible shutoff within 6 feet of, and in

the same room with, the dryer.

• Use pipe thread compound appropriate for

natural or LP gas or use Teflon

®

tape.

• Connect flexible metal connector to dryer and

gas supply.

IN THE COMMONWEALTH

OF MASSACHUSETTS

• This product must be installed by a licensed

plumber or gas fitter.

• When using ball-type gas shut-off valves, they

shall be the T-handle type.

• A flexible gas connector, when used, must not

exceed 3 feet.

2

5

⁄8″ (6.7 cm)

2″

(5.1 cm)

ADJUSTING FOR ELEVATION

• Gas clothes dryers input ratings are based on

sea level operation and need not be adjusted

for operation at or below 2000 ft. elevation.

For operation at elevations above 2000 ft., input

ratings should be reduced at a rate of 4 percent

for each 1000 ft. above sea level.

• Installation must conform to local codes and

ordinances or, in their absence, the NATIONAL

FUEL GAS CODE, ANSI Z223.

Install a 1/8″ NPT plugged tapping to the dryer

gas line shut-off valve for checking gas inlet

pressure.

Install a flare union adapter to the plugged

tapping.

NOTE: Apply pipe compound or Teflon

®

tape to

the threads of the adapter and plugged tapping.

Installation Instructions

Attach the flexible metal gas line connector to

the adapter.

B

Tighten the flexible gas line connection, using

two adjustable wrenches.

C

D

Tighten all connections, using two adjustable

wrenches. Do not overtighten.

E

CONNECTING THE DRYER

TO THE GAS SUPPLY (cont.)

Apply pipe compound or

Teflon

®

tape to all male

threads.

Open the gas shut-off valve.

F

Shut-Off Valve

Plugged

Tapping

CONNECTING THE DRYER

TO THE GAS SUPPLY

Install a female 3/8″ NPT elbow at the end

of the dryer gas inlet.

Install a 3/8″ flare union adapter to the female

elbow.

IMPORTANT: Use a pipe wrench to securely

hold on to the end of the dryer gas inlet

to prevent twisting the inlet.

NOTE: Apply pipe compound or Teflon

®

tape to

the threads of the adapter and dryer gas inlet.

Elbow

A

Adapter

Items not supplied

Adapter

1/8″ NPT

Pipe Plug for

Checking Gas

Inlet Pressure

Shut-Off Valve

Pipe size at

least 1/2″

3/8″ NPT

New Metal

Flexible Gas

Line Connector

Apply pipe compound to the

adapter and dryer gas inlet.

20

CONNECTING A GAS DRYER (cont.)

La page charge ...

GE DPVH890EJMG Le manuel du propriétaire

GE DPVH890EJMG Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents