Hitachi DS 12DVF3 Safety Instructions And Instruction Manual

Marque: Hitachi

Modèle: DS 12DVF3

Catégorie: Tournevis électriques

Taper: Safety Instructions And Instruction Manual

Ce manuel convient également à

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner

la mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser

l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs

et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être

conservé dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual BEFORE operating the power tool. Please keep this

manual available for other users and owners before they use the power tool. This

manual should be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de utilizar la herramienta

eléctrica. Este manual debe ser guardado en un lugar seguro.

DS18DVF3

DS 12DVF3

•

DS 14DVF3

DS 18DVF3

Model

Cordless Driver Drill

Modèle

Perceuse-visseuse sans fil

Modelo

Taladro atornillador a batería

01Eng_DS12DVF3_US 12/6/07, 11:361

CONTENTS

Page

ASSEMBLY AND OPERATION ............................... 12

APPLICATIONS ................................................... 12

REMOVAL AND INSTALLATION METHOD

OF BATTERY ................................................ 12

CHARGING METHOD ......................................... 12

BEFORE USE ....................................................... 13

OPERATION ......................................................... 13

THE SCOPE AND SUGGESTIONS

FOR USES .................................................... 18

HOW TO SELECT TIGHTENING TORQUE ......... 18

MAINTENANCE AND INSPECTION ....................... 19

TROUBLESHOOTING GUIDE ................................. 20

ACCESSORIES ......................................................... 21

STANDARD ACCESSORIES ............................... 21

OPTIONAL ACCESSORIES ................................. 22

PARTS LIST .............................................................. 61

TABLE DES MATIERES

Page

IMPORTANT INFORMATION ............................. 4

MEANINGS OF SIGNAL WORDS ...................... 4

SAFETY .................................................................... 4

GENERAL SAFETY RULES – FOR ALL

BATTERY OPERATED TOOLS ..................... 4

SPECIFIC SAFETY RULES AND SYMBOLS ....... 5

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER ........................... 6

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER .................................... 7

DISPOSAL OF THE EXHAUSTED BATTERY ..... 7

FUNCTIONAL DESCRIPTION .................................. 9

MODEL ................................................................. 9

NAME OF PARTS ................................................ 9

SPECIFICATIONS ................................................ 11

English

Français

Page

INFORMATIONS IMPORTANTES DE SÉCURITÉ ..

SIGNIFICATION DES MOTS D’AVERTISSEMENT

.. 23

SÉCURITÉ ................................................................ 23

REGLES GENERALE DE S

CURIT

– POUR TOUS LES

OUTILS FONCTIONNANT SUR BATTERIE

...... 23

REGLES DE SÉCURITÉ SPÉCIFIQUES ET

SYMBOLES .................................................. 24

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR LE

CHARGEUR DE BATTERIE

............................... 25

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L’UTILISATION DE LA BATTERIE ET DU

CHARGEUR DE BATTERIE

........................... 26

MISE AU REBUT D’UNE BATTERIE USÉE ........ 27

DESCRIPTION FONCTIONNELLE ........................... 28

MODÈLE .............................................................. 28

NOM DES PARTIES ............................................ 28

SPECIFICATIONS ................................................ 30

Page

ASSEMBLAGE ET FONCTIONNEMENT ................ 31

UTILISATIONS .................................................... 31

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 31

MÉTHODE DE RECHARGE ................................. 31

AVANT L’UTILISATION ...................................... 32

UTILISATION ....................................................... 32

PLAGE D’UTILISATION ET SUGGESTIONS ..... 37

SÉLECTION DU COUPLE DE SERRAGE ............ 37

ENTRETIEN ET INSPECTION .................................. 38

GUIDE DE DÉPANNAGE ......................................... 39

ACCESOIRES ........................................................... 40

ACCESSOIRES STANDARD ............................... 40

ACCESSOIRES EN OPTION ................................ 41

LISTE DES PIECES ................................................... 61

HITACHI AUTHORIZED SERVICE CENTERS

Service under this warranty is available from Hitachi Koki U.S.A., Ltd. at:

IN THE U.S.A. IN CANADA

3950 Steve Reynolds Blvd. Norcross, GA 30093

450 Export Blvd. Unit B, Mississauga, ON L5T 2A4

9409 Owensmouth Ave. Chatsworth, CA 91311

OR CALL: (800) 829-4752 for a service center OR CALL: (800) 970-2299 for a service center

nearest you. nearest you.

CENTRES TECHNIQUES HITACHI AGREES

La réparation est réalisée dans le cadre de cette garantie par Hitachi Koki U.S.A., Ltd.:

AUX ETATS-UNIS AU CANADA

3950 Steve Reynolds Blvd. Norcross, GA 30093

450 Export Blvd. Unit B, Mississauga, ON L5T 2A4

9409 Owensmouth Ave. Chatsworth, CA 91311

OU APPELEZ LE: (800) 829-4752 pour connaître OU APPELEZ LE: (800) 970-2299 pour connaître

le centre technique le plus le centre technique le plus

proche de chez vous. proche de chez vous.

01Eng_DS12DVF3_US 12/6/07, 11:362

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD ................................................. 42

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ............................................ 42

SEGURIDAD ............................................................. 42

NORMAS GENERALES DE SEGURIDAD – PARA

TODAS LAS HERRAMIENTAS

ALIMENTADAS CON BATERÍA ................... 42

NORMAS Y SÍMBOLOS ESPECÍFICOS DE

SEGURIDAD ................................................. 43

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

.......... 44

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD PARA LA BATERÍA Y EL

CARGADOR DE BATERÍAS ......................... 45

ELIMINACIÓN LAS BATERÍAS AGOTADAS ..... 46

DESCRIPCIÓN FUNCIONAL .................................... 47

MODELO .............................................................. 47

NOMENCLATURA ............................................... 47

ESPECIFICACIONES ............................................ 49

Página

MONTAJE Y OPERACIÓN ...................................... 50

APLICACIONES ................................................... 50

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................ 50

MÉTODO DE CARGA .......................................... 50

ANTES DE LA UTILIZACIÓN .............................. 51

OPERACIÓN ........................................................ 51

ALCANCE Y SUGERENCIAS PARA LA

UTILIZACIÓN ................................................ 56

FORMA DE SELECCIONAR EL PAR DE

APRIETE ........................................................ 56

MANTENIMIENTO E INSPECCIÓN ........................ 57

GUIA DE IDENTIFICACION DE PROBLEMAS ........ 58

ACCESORIOS ........................................................... 59

ACCESORIOS ESTÁNDAR ................................. 59

ACCESORIOS OPCIONALES .............................. 60

LISTA DE PIEZAS .................................................... 61

CENTROS DE SERVICIO AUTORIZADOS DE HITACHI

Hitachi Koki U.S.A., Ltd. proporciona un servicio de reparaciones bajo esta garantía en:

EN EE. UU. EN CANADA

3950 Steve Reynolds Blvd. Norcross, GA 30093

450 Export Blvd. Unit B, Mississauga, ON L5T 2A4

9409 Owensmouth Ave. Chatsworth, CA 91311

O LLAME AL: (800) 829-4752 para informarse O LLAME AL: (800) 970-2299 para informarse

del centro de reparaciones más del centro de reparaciones más

cercano. cercano.

01Eng_DS12DVF3_US 12/6/07, 11:363

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual

before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the

power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situation which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS

WARNING:

Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit.

Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust.

Power tools create sparks which may ignite

the dust of fumes.

(3) Keep bystanders, children and visitors away

while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) A battery operated tool with integral

batteries or a separate battery pack must be

recharged only with the specified charger for

the battery.

A charger that may be suitable for one type

of battery may create a risk of fire when used

with another battery.

(2) Use battery operated tool only with

specifically designed battery pack.

Use of any other batteries may create a risk

of fire.

3. Personal Safety

(1) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use tool while tired or under the

influence of drugs, alcohol, or medication.

A moment of inattention while operating

power tools may result in serious personal

injury.

(2) Dress properly. Do not wear loose clothing

or jewelry. Contain long hair. Keep your hair,

clothing and gloves away from moving parts.

Loose clothes, jewelry, or long hair can be

caught in moving parts.

(3) Avoid accidental starting. Be sure switch is

off position before inserting battery.

Carrying tools with your finger on the switch

or inserting the battery pack into a tool that

have the switch on invites accidents.

(4) Remove adjusting keys or wrenches before

turning the tool on.

A wrench or a key that is left attached to a

rotating part of the tool may result in personal

injury.

(5) Do not overreach. Keep proper footing and

balance at all times.

Proper footing and balance enable better

control of the tool in unexpected situations.

01Eng_DS12DVF3_US 12/6/07, 11:364

English

(6) Use safety equipment. Always wear eye

protection.

Dust mask, non-skid safety shoes, hard hat,

or hearing protection must be used for

appropriate conditions.

4. Tool Use and Care

(1) Use clamps or other practical way to secure

and support the workpiece to a stable

platform.

Holding the work by hand or against your

body is unstable and may lead to loss of

control.

(2) Do not force tool. Use the correct tool for your

application.

The correct tool will do the job better and safer

at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on

or off.

Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

(4) Disconnect battery pack from tool or place

the switch in the locked or off position before

making any adjustments, changing

accessories, or storing the tools.

Such preventive safety measures reduce the

risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and

other untrained persons.

Tools are dangerous in the hands of untrained

users.

(6) When battery pack is not in use, keep it away

from other metal objects like: paper clips,

coins, keys, nails, screws, or other small

metal objects that can make a connection

from one terminal to another.

Shorting the battery terminals together may

cause sparks, burns, or a fire.

(7) Maintain tools with care. Keep cutting tools

sharp and clean.

Properly maintained tools, with sharp cutting

edges are less likely to bind and are easier to

control.

(8) Check for misalignment or binding of moving

parts, breakage of parts, and any other

condition that may affect the tools operation.

If damaged, have the tool serviced before

using.

Many accidents are caused by poorly

maintained tools.

(9) Use only accessories that are recommended

by the manufacturer for your model.

Accessories that may be suitable for one tool,

may become hazardous when used on

another tool.

5. Service

(1) Tool service must be performed only by

qualified repair personnel.

Service or maintenance performed by

unqualified personnel could result in a risk of

injury.

(2) When servicing a tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual.

Use of unauthorized parts or failure to follow

Maintenance Instruction may create a risk of

electric shock or injury.

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities

contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

●

Lead from lead-based paints,

●

Crystalline silica from bricks and cement and other

masonry products, and

●

Arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

specially designed to filter out microscopic particles.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. ALWAYS wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

3. NEVER place hands or other body parts near the

drill bit or chuck during operation. Hold the drill

by its handle only.

4. Because the cordless driver drill operates by

battery power, be aware of the fact that it can begin

to operate at any time.

5. When working at elevated locations, clear the area

of all other people and be aware of conditions

below you.

6. NEVER touch moving parts.

NEVER place your hands, fingers or other body

parts near the tool’s moving parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or

safety features in place and in proper working

order. If maintenance or servicing requires the

removal of a guard or safety feature, be sure to

replace the guard or safety feature before resuming

operation of the tool.

01Eng_DS12DVF3_US 12/6/07, 11:365

English

8. Use right tool.

Don’t force small tool or attachment to do the job

of a heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

9. NEVER use a power tool for applications other

than those specified.

NEVER use a power tool for applications other than

those specified in the Instruction Manual.

10. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

12. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

13. Blades and accessories must be securely mounted

to the tool.

Prevent potential injuries to yourself or others.

Blades, cutting implements and accessories which

have been mounted to the tool should be secure

and tight.

14. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually,

making strange noises, or otherwise appears

defective, stop using it immediately and arrange

for repairs by a Hitachi authorized service center.

15. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly

dampened with soapy water and dry thoroughly.

17. ALWAYS wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

18. Definitions for symbols used on this tool.

...............

volts

—

---

..............

direct current

.............

no load speed

---/min

......

revolutions per minute

IMPORTANT SAFETY INSTRUCTIONS FOR

BATTERY CHARGER

1. This manual contains important safety and

operating instructions for battery charger Model

UC18YG.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger,

(2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI

rechargeable battery types EB1214S, EB1414S,

EB1814SL and EB1820L. Other type of batteries

may burst causing personal injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold

by the battery charger manufacturer may result in

a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

7. Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected

to damage or stress.

8. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in

good electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as specified in Table

01Eng_DS12DVF3_US 12/6/07, 11:366

English

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

02 1818 18 16

23 1818 16 14

34 1818 16 14

If the input rating of a battery charger is given in

watts rather than in amperes, the corresponding

ampere rating is to be determined by dividing the

wattage rating by the voltage rating–for example:

9. Do not operate battery charger with damaged cord

or plug-replace them immediately.

10. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged

in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a

qualified serviceman when service or repair is

required. Incorrect reassembly may result in a risk

of electric shock or fire.

12. To reduce risk of electric shock, unplug charger

from receptacle before attempting any

maintenance or cleaning. Removing the battery

will not reduce this risk.

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE BATTERY AND BATTERY

CHARGER

You must charge the battery before you can use the

cordless driver drill. Before using the model UC18YG

battery charger, be sure to read all instructions and

cautionary statements on it, the battery and in this

manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPES

EB1214S, EB1414S, EB1814SL, AND EB1820L. OTHER

TYPES OF BATTERIES MAY BURST AND CAUSE

INJURY!

Follow these instructions to avoid the risk of injury:

WARNING:

Improper use of the battery or

battery charger can lead to serious

injury. To avoid these injuries:

1,250watts

125 volts

10 amperes

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is

damaged or is completely worn out. The battery

can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery

charger’s air vents. Electric shock or damage to

the battery charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is

low humidity and good ventilation.

6. NEVER charge when the temperature is below

50°F (10°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to

charge.

11. NEVER store the battery or battery charger in

places where the temperature may reach or exceed

104°F (40°C).

12. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on

any other voltage may overheat and damage the

charger.

13. ALWAYS wait at least 15 minutes between

charges to avoid overheating the charger.

14. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

DISPOSAL OF THE EXHAUSTED BATTERY

WARNING:

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The

product that you have purchased contains a

rechargeable battery. The battery is recyclable. At

the end of it’s useful life, under various state and

local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste officials for details in

your area for recycling options or proper disposal.

01Eng_DS12DVF3_US 12/6/07, 11:367

English

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

01Eng_DS12DVF3_US 12/6/07, 11:368

English

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe operation and

maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ from those on your

own power tool.

MODEL

DS12DVF3: with charger and case

DS14DVF3: with charger and case

DS18DVF3: with charger and case

NAME OF PARTS

1. Cordless Driver Drill

Switch Trigger

Clutch Dial

Keyless Chuck

Shift Knob

Handle

Push Button

Nameplate

Housing

Indication

Battery

Indication

Clutch Dial

Keyless Chuck

Shift Knob

Handle

Push Button

Housing

Switch Trigger

Battery

Nameplate

Indication

01Eng_DS12DVF3_US 12/6/07, 11:369

English

䡬

Battery

(For DS12DVF3) (For DS14DVF3) (For DS18DVF3)

Nameplate

Latch

Fig. 1

2. Battery Charger (UC18YG)

Fig. 2

Latch

Nameplate

Indication

Clutch Dial

Keyless Chuck

Shift Knob

Handle

Push Button

Housing

Switch Trigger

Battery

Nameplate

Indication

Nameplate

Latch

Battery Installation Hole

Pilot Lamp

Cord

Plug

Nameplate

Terminal Hole Terminal

Hole

Terminal Hole

01Eng_DS12DVF3_US 12/6/07, 11:3610

English

SPECIFICATIONS

1. Cordless Driver Drill

Model UC18YG

Input power source Single phase: AC 120 V 60 Hz

Charging time Approx. 30 min......

EB1214S, EB1414S, EB1814SL

(At a temperature of 68°F (20°C)) Approx. 50 min...... EB1820L

Charging voltage DC 7.2 – 18 V

Charging current DC 2.6 A

Weight 0.7 lbs. (0.3 kg)

2. Battery Charger

Model DS12DVF3 DS14DVF3 DS18DVF3

Motor DC motor

No-load speed

Low 0–350/min 0–400/min 0–400/min

High 0–1050/min 0–1200/min 0–1200/min

Wood

1 in. (25 mm)

1–3/16 in. (30 mm) 1–1/2 in. (38 mm)

(Thickness

11/16 in.

Drilling

(18 mm))

(Soft Wood) (Soft Wood) (Soft Wood)

Metal 15/32 in. (12 mm) 15/32 in. (12 mm) 1/2 in. (13 mm)

Capacity

(Thickness (Mild Steel) (Mild Steel) (Mild Steel)

1/16 in.

19/32 in. (15 mm) 19/32 in. (15 mm) 1/2 in. (13 mm)

(1.6 mm))

(Aluminum) (Aluminum) (Aluminum)

Screw

Wood screw

#12 × 2-1/2 in. #14 × 2-1/2 in. #20 × 3 in.

(5.8 mm × 63 mm) (6.2 mm × 63 mm) (8mm × 75 mm)

Driver

Small screw 1/4 in. (6 mm) 1/4 in. (6 mm) 1/4 in. (6 mm)

Drill chuck capacity

Maximum gripping

diameter 3/8 in. (10 mm)

diameter 1/2 in. (13 mm)

Model EB1214S EB1414S

EB1814SL / EB1820L

Battery Type Nickel cadmium battery

Voltage DC 12 V DC 14.4 V DC 18 V

Weight 3.3 lbs. (1.5 kg) 4.0 lbs. (1.8 kg) 4.4 lbs. (2.0 kg)

01Eng_DS12DVF3_US 12/6/07, 11:3611

English

ASSEMBLY AND OPERATION

Fig. 3

Latch

Push

Handle

Pull out

Insert

Battery

Latch

Handle

Insert

Battery

Push

Pull out

CHARGING METHOD

NOTE:

Before plugging into the receptacle, make sure the

following points.

䡬

The power source voltage is stated on the

nameplate.

䡬

The cord is not damaged.

WARNING:

Do not charge at voltage higher than indicated on

the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn up.

1. Insert the plug of battery charger into the

receptacle.

WARNING:

Do not use the electrical cord if

damaged. Have it repaired immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown

in Fig. 4. Make sure it contacts the bottom of the

battery charger.

Pilot

Lamp

Fig. 4

Battery

(EB1214S)

Battery

(EB1414S)

Battery

(EB1814SL or

EB1820L)

APPLICATIONS

䡬

Use as a drill

Drilling of soft steel, wood, plastic and aluminum

materials.

䡬

Use as a screwdriver

Tightening and loosening of machine screws,

wood screws and tapping screws.

REMOVAL AND INSTALLATION METHOD

OF BATTERY

䡬

How to install the battery.

Align the battery with the groove in tool handle

and slip it into place.

Always insert it all the way until it locks in place

with a little click, If not, it may accidentally fall out

of the tool, causing injury to you or someone

around you (Fig. 3).

䡬

How to remove the battery.

Withdraw battery from the tool handle while

pressing the latch (1 pc. or 2 pcs) of the battery

(Fig. 3).

01Eng_DS12DVF3_US 12/6/07, 11:3712

English

3. Charging

䡬

When the battery is connected to the battery

charger, charging will commence and the pilot

lamp will light on.

NOTE:

If the pilot lamp dose not light, pull out the plug

from the receptacle and check if the battery is

properly mounted.

䡬

In approx. 30 – 50 min., when the battery is fully

charged, the pilot lamp will go out.

NOTE:

The battery charging time becomes longer when

a temperature is low or the voltage of the power

source is too low.

When the pilot lamp does not go off even if more

than four hour has passed after start of the

charging, stop the charging and contact your

HITACHI AUTHORIZED SERVICE CENTER.

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out

the battery from the battery charger.

CAUTION:

●

When the battery charger has been continuously

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, wait 15 minutes

rest until the next charging.

●

If the battery is recharged when it is warm due

to battery use or exposure to sunlight, the pilot

lamp may not light.

The battery will not be recharged. In such a case,

let the battery cool before charging.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new

batteries and batteries that have not been used

for an extended period is not activated, the electric

discharge might be low when using them the first

and second time. This is a temporary

phenomenon, and normal time required for

recharging will be restored by recharging the

batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its

battery. If you continue to use the tool and exhaust

the electric current, the battery may be damaged

and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately

after use. If such a battery is recharged immediately

after use, its internal chemical substance will

deteriorate, and the battery life will be shortened.

Leave the battery and recharge it after it has cooled

for a while.

BEFORE USE

Check the work area to make sure that it is clear of debris

and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

OPERATION

1. Using the hook (Hook with bit holder or Light

equipped hook)

WARNING:

When using the hook, pay sufficient attention so

that the main equipment does not fall. If the tool

falls, there is a risk of accident.

CAUTION:

●

Do not attach the tip tool except phillips bit to the

tool main unit when carrying the tool main unit

with the hook suspended from a waist belt.

Injury may result if you carry the equipment

suspended from the waist belt with sharp tipped

components such as drill bit attached.

The hook can be installed on the right or left side

and the angle can be adjusted in 5 steps between

0° and 80°.

(1) Operating the hook

(a) Pull out the hook toward you in the direction

of arrow (A) and turn in the direction of arrow

(B) (Fig. 5).

(B)

Fig. 5

Hook

(A)

01Eng_DS12DVF3_US 12/6/07, 11:3713

English

(b) The angle can be adjusted in 5 steps (0°, 20°,

40°, 60°, 80°).

Adjust the angle of the hook to the desired

position for use.

(2) Switching the hook position

CAUTION:

●

If the tool falls, there is a risk that malfunction

and/or physical damage can occur. It is

recommended that you also use fall-preventing

wires, etc.

●

Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the

screw using a slotted head screwdriver or a

coin (Fig. 6).

1.1 Using the bit holder (Hook with bit holder)

䡬

Installing the bit

Slide the bit from the side, and then insert firmly

until the groove on the bit locks in the protruded

section of the hook.

䡬

Removing the bit

Securely hold the main unit and pull out the bit by

holding the tip with your thumb (Fig. 9).

Fig. 6

Loosen

Screw

Fig. 7

Spring

Hook

(b) Remove the hook and spring (Fig. 7).

and securely fasten with screw (Fig. 6).

NOTE:

Pay attention to the spring orientation. Install the

spring with larger diameter away from you (Fig.

8).

Fig. 9

Fig. 10

Switch

Hook

CAUTION:

●

Only Hitachi STANDARD ACCESSORIES phillips

bit (No. 2 × 65L; Code No. 983006) may be used.

Do not use other bits since they may come loose.

1.2 Using as an auxiliary light (Light equipped hook)

(1) Press the switch to turn off the light.

If forgotten, the light will turn off automatically after

15 minutes (Fig. 10).

(2) The direction of the light can be adjusted within

the range of hook positions 1 - 5 (Fig. 5).

䡬

Lighting time

N manganese batteries: approx. 15 hrs.

N alkali batteries: approx. 30 hrs.

CAUTION:

●

Do not look directly into the light.

Such actions could result in eye injury.

1.3 Replacing the batteries (Light equipped hook)

(1) Loosen the hook screw with a phillips-head

screwdriver (No. 1) (Fig. 11).

Remove the hook cover by pushing in the direction

of the arrow (Fig. 12).

Fig. 8

Screw

Larger diameter faces away

01Eng_DS12DVF3_US 12/6/07, 11:3714

English

(2) Remove the old batteries and insert the new

batteries. Align with the hook indications and

position the plus (+) and minus (–) terminals

correctly (Fig. 13).

Hook main body

Protube-

rance

Inden-

tation

batteries

Indentation

Protube-

rance

Hook cover

Fig. 13

Fig. 12

Arrow

Hook cover

Fig. 11

Hook

Phillips-head

screwdriver

Screw

(3) Align the indentation in the hook main body with

the protuberance of the hook cover, press the hook

cover in the direction opposite to that of the arrow

shown in Fig. 12 and then tighten the screw.

Use commercially available N batteries (1.5 V).

NOTE:

Do not tighten the screw excessively. Such action

could strip the screw threads.

CAUTION:

●

Failure to observe the following can result in

battery leakage, rust or malfunction.

Position the plus (+) and minus (–) terminals

correctly.

Replace both batteries at the same time. Do not

mix old and new batteries.

Remove exhausted batteries from the hook

immediately.

●

Do not discard batteries together with normal

trash and do not throw batteries into fire.

●

Store batteries out of the reach of children.

●

Use batteries correctly in accordance with the

battery specifications and indications.

2. Using the bit holder.

CAUTION:

●

Stow the bit in the specified location on the tool.

If the tool is used with the bit stowed improperly,

the bit may fall and cause bodily injury.

●

Do not stow bits that are of a different length,

gauge or dimension than the plus driver bit (65

mm long) included in the STANDARD

ACCESSORIES.

The bit may fall and cause bodily injury.

(1) Removing the bit

Securely hold the main unit and pull out the bit by

holding the tip with your thumb (Fig. 14).

Fig. 14

Bit

Fig. 15

Insert so that

bit does not

protrude

from main unit

(2) Installing the Bit

Install the bit with steps opposite of when

removing. Insert the bit so that the right and left

sides are equal, as shown in Fig. 15.

01Eng_DS12DVF3_US 12/6/07, 11:3715

English

3. Mounting and dismounting of the bit.

(1) Mounting the bit.

Insert a screwdriver bit etc. into the keyless drill

chuck.

Firmly grasp the ring and tighten the sleeve by

turning it toward the right (in the clockwise

direction as viewed from the front) (See Fig. 16).

Fig. 16

Tighten

Loosen

SleeveRing

NOTE:

If the sleeve becomes loose during operation,

tighten it further.

The tightening force becomes stronger when the

sleeve is tightened.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by

turning it toward the left (in the counterclockwise

direction as viewed from the front) (See Fig. 16).

CAUTION:

When mounting a bit into the keyless chuck,

tighten firmly. If the sleeve is not tight, the bit may

slip or fall out, causing injury.

NOTE:

Loosening stuck or hard to move sleeves.

Grasp the bit installed in the keyless chuck, in a

vise or similar tool.

Set the clutch dial position to “1-11” and turn on

the switch. The motor then starts.

Finally, rotate the sleeve to the left, and it will

loosen.

4. Confirm that the battery is mounted correctly.

5. Check the rotational direction.

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn

the bit counterclockwise (See Fig. 17).

(The

and

marks are provided on the body.)

Fig. 17

Selector

button

marks

Trigger

switch

marks

䡬

When the trigger switch is depressed, the tool

rotates. When the trigger is released, the tool stops.

䡬

The rotational speed of the drill can be controlled

by varying the amount that the trigger switch is

pulled. Speed is low when the trigger switch is

pulled slightly and increases as the trigger switch

is pulled more.

䡬

When releasing the trigger of the switch, the brake

will be applied for immediate stopping.

6. Change rotation speed.

Fig. 18

Shift knob

High speed

Fig. 19

Shift knob

Low speed

Operate the shift knob to change the rotational

speed. Move the shift knob in the direction of the

arrow (see Figs. 18 and 19).

When the shift knob is set to “LOW”, the drill

rotates at a low speed. When set to “HIGH”, the

drill rotates at a high speed.

01Eng_DS12DVF3_US 12/6/07, 11:3716

English

CAUTION:

●

When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating

will damage the gears.

●

When a large force is required for operation

(operations indicated in the following chart) set

the shift knob to “LOW”. If “HIGH” is set and the

unit is used, it may cause the motor to burn out

or malfunction prematurely.

Table 2

Model DS12DVF3 / DS14DVF3 DS18DVF3

Metal Drilling

Wood Drilling

Wood Screw

Tightening

When the diameter of the hole

exceeds 1/4 in. (6.5 mm).

When the diameter of the hole

exceeds 15/32 in. (12 mm).

When the size of the wood

screw exceeds 5/32 in. (3.8 mm)

diameter × 1-31/32 in. (50 mm).

When the diameter of the hole

exceeds 5/16 in. (8 mm).

When the diameter of the hole

exceeds 15/16 in. (24 mm).

When the size of the wood

screw exceeds 3/16 in. (4.8 mm)

diameter × 1-9/16 in. (40 mm).

7. Confirm the clutch dial position (see Fig. 20).

The tightening torque of this unit can be adjusted

according to the clutch dial position, at which the

clutch dial is set.

8. Tightening torque adjustment.

(1) Tightening torque

Tightening torque should correspond in its

intensity to the screw diameter. When too strong

power is used, the screw head may be broken or

be injured.

Be sure to adjust the clutch dial position according

to the screw diameter.

(2) Tightening torque indication (See Fig. 20)

The tightening torque differs depending on the

type of screw and the material being tightened.

The unit indicates the tightening torque with the

numbers “1, 3, 5 ... 22” on the clutch dial, and a

dot. The tightening torque at position “1” is the

weakest and the torque is strongest at the highest

number.

(3) Adjusting the tightening torque (See Fig. 20)

Rotate the clutch dial and line up the numbers “1,

3, 5, ... 22” on the clutch dial, or the dot, with the

triangle mark on the outer body. Adjust the clutch

dial in the weak or the strong torque direction

according to the torque you need.

CAUTION:

●

The motor rotation may be locked to cease while

the unit is used as drill. While operating the driver

drill, take care not to lock the motor.

Clutch dial

Triangle mark

Fig. 20

Weak

mark

Strong

Line

mark

Fig. 21

Triangle mark

(1) When using this unit as a screwdriver, line up the

one of the numbers “1, 3, 5 ... 22” on the clutch

dial, or the black dot, with the triangle mark on the

outer body.

(2) When using this unit as a drill, line up the clutch

dial drill mark “ ” with the triangle mark on the

outer body.

CAUTION:

●

The clutch dial cannot be set between the numbers

“1, 3, 5 ... 22” or the black dot.

●

Do not use with the clutch dial set at the line

between the number “22” and the drill mark

“ ”. Doing so may cause damage (See Fig. 21).

01Eng_DS12DVF3_US 12/6/07, 11:3717

English

●

When setting the shift knob to “HIGH” (high

speed) and the position of the clutch dial is “17”

to “22”, it may happen that the clutch does not

engaged and that the motor is locked. In such a

case, please set the shift knob to “LOW” (low

speed).

THE SCOPE AND SUGGESTIONS FOR USES

Table 3

●

If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor or

battery may be burnt.

●

Too long hammering may cause the screw broken

due to excessive tightening.

●

A buzzing noise is produced when the motor is about

to rotate; This is only a noise, not a machine failure.

Work Clutch dial position Suggestions

Wood

Drilling Steel Use for drilling purpose.

Aluminum

Machine

1 – 22

Use the bit and socket matching the

Screw

screw screw diameter.

tightening

Wood

1 –

Use after drilling a pilot hole.

screw

HOW TO SELECT TIGHTENING TORQUE

Table 4

Clutch dial

Tightening torque Operation example

position

Approximately 9 in.-lbs. (10 kg-cm)

Approximately 15 in.-lbs. (17 kg-cm)

Approximately 23 in.-lbs. (26 kg-cm)

Approximately 35 in.-lbs. (40 kg-cm)

Approximately 43 in.-lbs. (49 kg-cm)

Approximately 52 in.-lbs. (60 kg-cm)

High speed: approximately 61 in.-lbs.

(70 kg-cm) (DS12DVF3)

approximately 71 in.-lbs.

(82 kg-cm) (DS14DVF3)

approximately 97 in.-lbs.

(112 kg-cm) (DS18DVF3)

Low speed: approximately 230 in.-lbs.

(265 kg-cm) (DS12DVF3)

approximately 300 in.-lbs.

(347 kg-cm) (DS14DVF3)

approximately 400 in.-lbs.

(459 kg-cm) (DS18DVF3)

Machine screw

tightening Screw

tightening for soft wood

material

Screw tightening for

hard wood material

Thick screw tightening

When used as a drill.

01Eng_DS12DVF3_US 12/6/07, 11:3718

English

MAINTENANCE AND INSPECTION

CAUTION:

Pull out battery before doing any inspection or maintenance.

1. Checking the condition of the bit

The bits should be checked regularly. If worn or

broken bits can slip or decrease the efficiency of

the motor and burn it out.

Replace worn bits with new ones.

CAUTION:

If you use a driver bit of which point is worn or

broken, it will be dangerous since it slips. So

replace it with a new one.

2. Check the Screws

Loose screws are dangerous. Regularly inspect

them and make sure they are tight.

CAUTION:

Using this power tool with loosened, screws is

extremely dangerous.

3. Check for Dust

Dust may be removed with a soft cloth or a cloth

dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner,

for they may damage the plastics.

4. Disposal of the exhausted battery

WARNING:

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The

product that you have purchased contains a

rechargeable battery. The battery is recyclable. At

the end of it’s useful life, under various state and

local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste officials for details in

your area for recycling options or proper disposal.

5. Storage

Storing in a place below 104°F (40°C) and out of

the reach of children.

6. Service and repairs

All quality power tools will eventually require

servicing or replacement of parts because of wear

from normal use. To assure that only authorized

replacement parts will be used, all service and

repairs must be performed by a HITACHI

AUTHORIZED SERVICE CENTER, ONLY.

7. Service parts list

CAUTION:

Repair, modification and inspection of Hitachi

Power Tools must be carried out by an Hitachi

Authorized Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized

Service Center when requesting repair or other

maintenance. In the operation and maintenance

of power tools, the safety regulations and

standards prescribed in each country must be

observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest

technological advancements.

Accordingly, some parts (i.e. code numbers and/

or design) may be changed without prior notice.

NOTE:

The selected content shown in Table 4 indicates

the differences according to screw type, screw size

and material used.

CAUTION:

●

While operating the Cordless driver drill, take care

not to lock the motor.

If the motor is locked, immediately turn the power

off.

If the motor is locked for a while, the motor or

battery will be burnt.

●

Do not tighten too strongly as the screw heads

will be damaged.

01Eng_DS12DVF3_US 12/6/07, 11:3719

English

TROUBLESHOOTING GUIDE

•

To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source or

remove the battery from the main body before making any adjustments.

•

All electrical or mechanical repairs should be done only by qualified service technicians. Contact Hitachi

Authorized Service Center.

WARNING

Problem Possible Cause Possible Solution

Tool will not start.

Battery will not charged.

Battery not installed properly.

Battery not charged.

Battery overheated.

Battery pack not installed into Charger

properly.

Charger not plugged in.

Battery temperature too hot

Battery temperature too cold

Check the battery installation.

Charge battery using appropriate

charger.

Remove battery from tool and let battery

cool for while.

Insert battery into charger until charge

status lamp (red) appears.

Plug charger into a working receptacle.

Remove battery from charger, cool

battery.

For more detail, refer to “Charging

Method”.

Remove battery from charger, move

battery and charger to a surrounding air

temperature of above 50°F (10°C).

For more detail, refer to “Changing

Method”.

01Eng_DS12DVF3_US 12/6/07, 11:3720

La page charge ...

Hitachi DS 12DVF3 Safety Instructions And Instruction Manual

Marque: Hitachi

Modèle: DS 12DVF3

Catégorie: Tournevis électriques

Taper: Safety Instructions And Instruction Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi DS 12DVF3
español: Hitachi DS 12DVF3

Hitachi DS 12DVF3 Safety Instructions And Instruction Manual

Ce manuel convient également à

Hitachi DS 12DVF3 Safety Instructions And Instruction Manual

dans d''autres langues

Documents connexes