Epson BrightLink 595Wi Guide d'installation

Catégorie
Projecteurs
Taper
Guide d'installation

Ce manuel convient également à

Installation Guide
Guide d’installation
2
Safety Instructions
For your safety, read all the instructions in this guide before using the wall mount. Incorrect handling that
ignores instructions in this guide could damage the wall mount or could result in personal injury or property
damage. Keep this installation guide on hand for future reference.
Read the safety instructions in the User's Guide for your projector and follow the instructions in this document.
Explanation of Symbols
The warning marks shown below are used throughout this installation guide to prevent personal injury or
property damage. Make sure you understand these warnings when reading this installation guide.
Safety Precautions for Installation
This symbol indicates information that, if ignored, could possibly result in personal injury or even death
due to incorrect handling.
This symbol indicates information that, if ignored, could possibly result in personal injury or physical
damage due to incorrect handling.
This symbol indicates related or useful information.
Symbol indicating an action that must not be done
Symbol indicating an action that should be done
The wall mount is designed specifically for mounting a projector to a wall. If anything other than a
projector is mounted, the weight may result in damage.
If the wall mount falls, it could cause personal injury or property damage.
The installation work (wall mounting) should be performed by specialists who have technical knowledge
and ability. Incomplete or incorrect installation could cause the wall mount to fall and cause personal
injury or property damage.
Follow the instructions in this guide when installing the wall mount.
If the instructions are not followed, the wall mount may fall, resulting in personal injury or property damage.
Follow the instructions in this guide to install and operate the Touch Unit.
If the Touch Unit is not installed and operated properly, the light emitted from the laser could cause injury to
eyesight.
Handle the power cord carefully.
Incorrect handling may cause fire or electric shock. Observe the following precautions when handling:
• Do not handle the power plug with wet hands.
• Do not use a power cord that is damaged or modified.
• Do not pull the power cord with too much force when routing the cable through the wall mount.
Do not install the wall mount in a place where it might be subjected to vibration or shock.
Vibration or shock could cause damage to the projector or mounting surface. It could also cause the wall mount or
projector to fall and cause personal injury or property damage.
The installation work should be performed by at least two qualified service personnel. If you need to
loosen any screws during installation, be careful not to drop the wall mount.
If the wall mount or projector falls, it could cause personal injury or property damage.
Warning
Caution
Warning
3
English
Install the wall mount so that it can sufficiently support the weight of the projector and wall mount, and
resist any horizontal vibration. Use M10 nuts and bolts and make sure to use appropriate wall anchors for
your wall type.
Nuts and bolts smaller than M10 could cause the wall mount to fall. Epson accepts no responsibility for any
damage or injury caused by lack of wall strength or inadequate installation.
When you mount the projector on the wall with the wall mount, the wall requires enough strength to hold
the projector, the wall mount, and the Touch Unit.
This wall mount should be installed on a concrete wall. Confirm the weight of the projector, the wall mount,
and the Touch Unit before installation, and maintain the strength of the wall. If the wall is not strong
enough, reinforce the wall before installation.
Inspect the wall mount on a regular basis to ensure there are no broken parts or loose screws.
If there are any broken parts, stop using the wall mount immediately. If the wall mount or projector falls, it could
cause personal injury or property damage.
Never modify the wall mount or Touch Unit.
Do not hang on the wall mount or hang a heavy object on the wall mount.
If the projector or wall mount falls, it could cause personal injury or property damage.
Do not use adhesives, lubricants, or oils to install or adjust the wall mount.
If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the part of the
projector attached to the slide plate, the case may crack and cause the projector to fall, resulting in personal injury
or property damage.
Tighten all screws firmly after adjustment.
Otherwise, the projector or wall mount may fall and cause personal injury or property damage.
Never loosen the bolts and nuts after installation.
Confirm that the screws have not become loose on a regular basis. If you find any loose screws, tighten them
firmly. Otherwise, the projector or wall mount may fall and cause personal injury or property damage.
When performing wiring, make sure the cable does not come into contact with any screws or bolts.
Handling the cable incorrectly may cause fire or electric shock.
Do not apply optical devices such as a magnifying glass or telescope to the laser light diffused from the
Touch Unit.
If such optical devices are applied, it could cause personal injury or fire.
Do not look into the Touch Unit’s laser diffusion ports.
This could cause injury to eyesight. Extra care should be taken when children are present.
Do not view the laser light using optical devices such as a magnifying glass within a range of 2.75 inches
(70 mm).
Viewing at close range could cause injury to eyesight.
Connect the Touch Unit to BrightLink 595Wi/595Wi+ models only. Do not connect it to any other projectors
or devices.
Do not use the Touch Unit if you are using or near medical equipment such as a pacemaker.
The magnet within the Touch Unit generates electromagnetic interference which could cause medical equipment
to malfunction.
Do not install the wall mount in a location where the operating temperature for your projector model may
be exceeded. Such an environment may damage the projector.
Warning
Caution
4
Installation Location
Before installing the projector, verify the power supply wiring for the installation location.
Install the projector away from other electric devices such as fluorescent lights or air conditioners. Some
kinds of fluorescent lights could interfere with the remote control of the projector.
Install the projector away from direct sunlight and other bright light sources.
It is recommended to keep VGA computer cable length less than 65 ft (20 meters) to reduce external
noise.
Install the projector in a location where the projected image is within reach.
The projector must be installed in one of the following locations in order for the Touch Unit to function
properly:
Mounted on a wall or suspended from the ceiling with images projected from in front of the screen.
Mounted vertically on a table with images projected from the front of the table. If using this
installation method, you need the optional interactive table mount (ELPMB29) and attachment plate
(ELPPT05).
Before installing the Touch Unit, verify that the installation location meets the following conditions:
The Touch Unit can be secured to the surface with magnets or screws.
The surface is flat, smooth, and unwarped with no more than 0.2 inches (5 mm) of unevenness on the
screen surface.
Install the wall mount in a place free from excessive dust and humidity to prevent the lens or optical
components from becoming dirty.
Do not use excessive force when adjusting the wall mount.
The wall mount may break, resulting in personal injury.
Keep magnetic storage media (for example, magnetic cards or electronic devices such as computers,
digital watches, or cell phones) away from the Touch Unit.
The magnet within the Touch Unit generates electromagnetic interference which could corrupt data or cause the
media or device to malfunction.
Caution
0.2 in. (5 mm)
5
English
When installing on a whiteboard, install the Touch Unit within the frame of the whiteboard.
Make sure there are no obstacles, such as cables, or protruding objects such as whiteboard trays, pen
holders, or thick frames in the shaded areas in the following figure. The Touch Unit will not operate
correctly if anything is obstructing the infrared signal.
About This Installation Guide
This guide describes how to mount the ultra-short-throw projectors BrightLink 595Wi/595Wi+ to a wall using
the included Epson wall mount. It also explains how to install the Touch Unit after wall mount installation.
Correct position Incorrect position
0.8 in. (20 mm)
4.0 in. (100 mm)4.0 in. (100 mm)
6
1 Package Contents
s 8
2 Specifications
s 10
3 Connecting Devices
s 13
4 Positioning the Projector
1. Installation worksheet for projecting on a pre-installed wall-mounted board
2. Installation worksheet for projecting on a plain wall
3. Diagonal image size and mounting position
4. Distance from projection surface to wall plate
5. Installation Measurements in Inches for BrightLink 595Wi/595Wi+
6. Installation Measurements in Millimeters for BrightLink 595Wi/595Wi+
s 14
5 Installing the Projector
1. Disassemble the parts
2. Assemble the parts
3. Install the wall plate on the wall
4. Determine the projection distance and pull out the slider
5. Route the cables through the wall mount arm
6. Attach the mount arm to the wall plate
7. Adjust the vertical slide position of the arm
8. Attach the projector to the wall mount
9. Connect the power cord and other cables to the projector
s 24
6 Adjusting the Image
1. Turn on the projector
2. Display the test pattern
3. Change the aspect ratio if necessary
4. Adjust the focus
5. Use the adjustment knob on the left side to adjust the horizontal roll
6. Use the adjustment knob on the right side to adjust the horizontal rotation
7. Use the adjustment knob on the top to adjust the vertical tilt
8. Adjust the horizontal slide
9. Adjust the forward/backward slide
10. Adjust the vertical slide
11. Turn off the display of the test pattern
s 35
7
English
7 Attaching the Covers
1. Attach the wall plate cover and end cap
2. Attach the cable cover to the projector
s 40
8 Installing the Touch Unit
1. Turn on the projector
2. Display the installation pattern
3. Remove the markers
4. Determine the installation position for the Touch Unit
5. Install the Touch Unit
6. Connect the cable
7. Adjust the angle
8. Store the markers and attach labels
9. Attach cover
s 42
9 Appendix
1. Using the Easy Interactive Function
2. Attaching a Security Cable
s 55
8
1 Package Contents
Wall Mount
Use the bolts or screws supplied with the wall mount to install it as directed in this guide. Do not
substitute these bolts with any other types.
You need to use commercially available M10 x 60 mm anchors (at least 3) to attach the wall plate to the
wall.
Gather the tools and parts you need before you begin installation, including a #3 cross-head screwdriver.
Shape Name Quantity Application
M4 x 12 mm hexagon socket head cap bolt with
washer/spring washer
6 For wall plate assembly
4 For 3-axis adjustment unit/wall mount
installation
4 For slide plate/projector installation
2 For slide plate/3-axis adjustment unit
installation (secured when shipped)
M6 x 20 mm hexagon shoulder bolt with washer/
spring washer
1 For wall mount/wall plate installation
M6 x 20 mm cross recessed head shoulder screw
with plastic washer
3
Hexagon wrench (for M4)
Wall plate cover
Wall mount
Template sheet
(for installing the wall plate)
End cap
3-axis adjustment unit and slide
plate (attached when shipped)
Open-ended wrench
13 mm (for M8 and M6) x
6 mm (for hexagonal
shaft)
Wall plate
VGA computer cable (may be included
with projector or wall mount)
Hexagonal shaft
Wall plate cover extender
9
English
Touch Unit
The following parts are packaged with your projector and are necessary when attaching the Touch Unit. When
installing the Touch Unit on a non-magnetic surface, you will also need three M4 screws.
Tape (approx. 2.4 inches
[6 cm]) for securing the
markers ×12
Label (×4)
Touch Unit and markers
(markers are inside the unit)
Touch Unit connection cable
Infrared deflector (approx.
11.2 inches [28.5 cm]) ×8
10
2Specifications
Wall plate
The wall plate is in three pieces when shipped. Use the included M4 x 12 mm bolts (x6) to attach the separate
pieces together before mounting the projector. See page 25 for instructions.
Vertical slide adjustment range
Item Specification Additional information Reference
Page
Wall mount weight (including the
3-axis adjustment unit, slide plate,
wall plate, wall plate cover, wall
plate cover extender, and end cap)
Approx. 18.5 lb
(8.4 kg)
Wall mount: 6.6 lb (3.0 kg)
3-axis adjustment unit: 2.6 lb (1.2 kg)
Slide plate: 1.8 lb (0.8 kg)
Wall plate: 6.0 lb (2.7 kg)
Wall plate cover and end cap: 0.9 lb (0.4 kg)
Wall plate cover extender: 0.6 lb (0.3 kg)
Maximum load capacity 15.4 lb (7 kg)
Vertical slide adjustment range ± 1.5 in. (38 mm) Refer to the
illustration
below
Horizontal slide adjustment range ± 1.8 in. (45 mm) Refer to the
illustration on
page 11
Forward/backward slide
adjustment range
0 to 14.2 in.
(360 mm)
Arm slide adjustment range: 0 to 10.7 in. (273 mm)
Adjustment from 3-axis adjustment unit installation
position: 3.4 in. (87 mm)
Refer to the
illustration on
page 11
Horizontal roll adjustment range ± 3° Fine adjustments possible with adjustment knob
s p. 37
Horizontal rotation adjustment
range
± 8° Fine adjustments possible with adjustment knob
s p. 37
Vertical tilt adjustment range ± 3° Fine adjustments possible with adjustment knob
s p. 38
5.1 in.
(130 mm)
1.0 in.
(25 mm)
1.3 in.
(33 mm)
3.2 in.
(80 mm)
4.2 in.
(106.5 mm)
3.1 in.
(79 mm)
2.4 in.
(60 mm)
4.6 in. (117 mm)
8.8 in. (223 mm)
6.3 in. (160 mm)
8.4 in. (213 mm)
19.5 in. (496 mm)
8.7 in. (222 mm)
9.7 in. (246 mm)
1.2 in.
(30.6 mm)
1.5 in. (38 mm)
1.5 in. (38 mm)
11
English
Horizontal slide adjustment range
Forward/backward slide adjustment range
Arm slide adjustment range
Adjustment from 3-axis adjustment unit installation position
By changing the installation position of the 3-axis adjustment unit to the front or back, you can adjust the
installation position of the projector.
When the screen size is less than 75 inches, install it at the position marked with a stamp on the mount arm.
When the screen size is 75 inches or more, install it at the position marked with a stamp on the mount
arm.
To see these stamps, you need to remove the two top screws and slide out the arm extension.
1.8 in. (45 mm)
1.8 in. (45 mm)
10.7 in. (273 mm)
3.4 in.
(87 mm)
Stamp
Stamp
12
Touch Unit
External dimensions and weight
The Touch Unit weighs approximately 16 ounces (450 g).
Attached labels
The Touch Unit is a Class 1 laser product that conforms to the JIS C 6802:2011 standard. There are warning
labels affixed to the Touch Unit to indicate that it is a Class 1 laser product. The labels contain the following
information:
Invisible laser radiation
Do not view the beam directly with optical instruments
Class 1 laser product
Laser diffusion port
The laser beam is diffused from the laser diffusion ports on the back of the Touch Unit.
8.3 in. (210 mm)
3.7 in. (95 mm)
2.0 in.
(51 mm)
Laser diffusion ports
13
English
3Connecting Devices
Make sure you have the power cord, computer cable, and other parts at the location where the wall mount is
to be installed.
Make sure you also have all necessary cables for the Touch Unit and other devices, such as a document camera
or microphone, that you will connect to the projector. For details, refer to the online Users Guide.
External speakers
LAN device
Microphone
USB cable (for Easy
Interactive Function)
Document camera
(Epson DC-06)
Computer
Computer cable
(for computer video
output)
Connection Example
Dedicated USB cable
(supplied with document camera)
Audio cable
(not included)
LAN cable
(not included)
Touch Unit connection
cable
Touch Unit
When interacting with a computer, you need a USB cable. However, when using the projector's
built-in toolbar, you do not need a USB cable.
For Interactive Use
14
4 Positioning the Projector
BrightLink 595Wi/595Wi+ can project up to 100 inches diagonally for a WXGA image or 88 inches diagonally
for an XGA image. You can project onto a pre-installed whiteboard or directly onto a plain wall. When
installing the Touch Unit, install it on the screen that is being used for projection; you need at least 4.7 inches
(120 mm) between the top edge of the projected image and the top edge of the screen. The height of the
included wall mount determines the maximum image size and how high the image appears on the wall or
whiteboard. The distance of the projector from the wall (once it is mounted on the adjustable arm of the wall
mount) also affects image size and position.
If you are planning to project on a whiteboard, the image may not fill the entire board, depending on the
aspect ratio. If you match the image height to the board’s height, gaps may appear on the sides of the board.
Use the following worksheets to determine the proper location of the wall plate on the wall. If you are
projecting onto a pre-installed whiteboard, use the worksheet on page 15. If you are projecting on a plain
wall, use the worksheet on page 16.
When installing on a whiteboard, make sure to leave the following gaps around the
edge of the board:
From the top of the projected image to the bottom of the Touch Unit: 1 inch
(25 mm)
From the edges of the projected image to the edges of the board: at least 4 inches
(100 mm) left and right
From the bottom of the projected image to the bottom of the board: 0.8 inches
(20 mm)
If there are obstacles such as cables, whiteboard trays, pen holders, or frames within
the areas listed above, the Touch Unit will not operate properly.
15
English
Installation worksheet for projecting on a pre-installed wall-mounted
board
1. Measure the ceiling height (distance from the floor to the ceiling). _____
2. Measure the height of the board’s image area (h). _____ (h)
3. Measure the width of the board’s image area (w). _____ (w)
4. Measure the distance from the floor to the bottom of the board’s image area (f). _____ (f)
5. Measure the distance from the ceiling to the top of the board’s image area (d). _____ (d)
6. Measure the thickness of the board (distance from the projection surface to the wall) (x). _____ (x)
7. Determine the aspect ratio of the board or of the images that will be projected. For new
computers or laptops, this will most likely be WXGA (16:10). For older equipment, this will
most likely be XGA (4:3). You may need to consult your IT department for this
information.
___ 4:3 XGA ___ 16:10 WXGA ___ 16:9 Widescreen
8. Using the tables on pages 19 to 21 for your aspect ratio and desired image height (h), find
the required distance between the top of the image area and the bottom holes of the
wall plate (c).
_____ (c)
9. Determine the position for your projector installation by adding the values for (f), (h), and
(c), plus an additional 10 inches for the height of the wall plate plus the cover.
If the ceiling height of your room (as noted in step 1) does not meet the minimum
ceiling height required for your board, you may need to select a smaller image size or
move the board to a lower position on the wall.
_____ (f)
_____ (h)
_____ (c)
+10
inches
_____ total
10. After confirming your image size, use tape or a pencil to mark the distance (c) from the
top of the image area on the board to the bottom holes of the wall plate.
11. Align the line (horizontal) on the template sheet with the (c) mark, then align the
center line on the template sheet with the center of the image area. Follow the
instructions on page 24 to install the projector.
10 in. (254 mm)—height of
wall plate plus cover
Required distance from top
of image area to bottom
holes of wall plate (c)
Diagonal size of
image area (S)
Height of
image area (h)
Distance from ceiling to
top of image area (d)
Width of image area (w)
Distance from floor to
bottom of image area (f)
4.0 in. (100 mm)—
distance from edge of
image area to edge of
board
1.0 in. (25 mm)—distance
from top of image area to
bottom of Touch Unit
0.8 in. (20 mm)—
distance from bottom
of image area to
bottom of board
4.7 in. (119 mm)—
distance from top of
image area to top of
board
16
Installation worksheet for projecting on a plain wall
1. Measure the ceiling height (distance from the floor to the ceiling). _____
2. Determine the desired aspect ratio of the image. For new computers or laptops, this
will most likely be WXGA (16:10). For older equipment, this will most likely be XGA (4:3).
You may need to consult your IT department for this information.
___ 4:3 XGA ___ 16:10 WXGA ___ 16:9 Widescreen
3. Using the tables on pages 19 to 21 for your aspect ratio, select the largest image size
available for your ceiling height.
Image height (h)
Image width (w)
_____ (h)
_____ (w)
4. Determine the desired distance from the floor to the bottom of the image area (f).
The recommended minimum distance is 30 inches. Images appearing less than 28
inches from the floor may be obstructed for some viewers.
_____ (f)
5. Find the top of the projected image area by adding distances (f) and (h). _____
6. Use the tables on pages 19 to 21 to determine the required distance from the top of the
image area to the bottom holes of the wall plate (c). _____ (c)
7. Add:
Required distance from top of image area to bottom holes of wall plate (c)
Height of image area (h)
Distance from floor to bottom of image area (f)
Height of wall plate plus cover
If the total exceeds the ceiling height, you will need to reduce the image size or reduce
the distance from the floor to the bottom of the image area.
_____ (c)
_____ (h)
_____ (f)
+10
inches
_____ total
10 in. (254 mm)—height of
wall plate plus cover
Required distance from top of
image area to bottom holes of
wall plate (c)
Diagonal size of
image area (S)
Height of
image area (h)
Distance from ceiling
to top of image area (d)
Width of image area (w)
Distance from floor to
bottom of image area (f)
1 in. (25 mm)—distance
from top of image area to
bottom of Touch Unit
Ceiling height
17
English
The tables on the following pages provide installation information for all supported image sizes. The
minimum ceiling height is based on an image 30 inches from the floor; if the image is lower, the minimum
ceiling height is reduced by the corresponding measurement.
Use the worksheets, the illustrations, and the information in the tables on the following pages to determine
the projection distance and placement of the wall plate. The recommended range for projection distance (a)
as shown on the following pages is 2.5 to 12.2 inches (62 to 311 mm).
Diagonal image size and mounting position
The numbers on the slider measure (b) are the same as the projection distance (a) when the diagonal image
size (S) is 75 inches or more. Because the installation position of the projector changes when (S) is less than 75
inches, the numbers for (a) and (b) differ.
In order to see the stamp and the numbers on the slider scale, you need to slide out the arm extension.
When the diagonal image size is 75 inches or more, mount the 3-axis adjustment unit at the position marked
with a stamp.
8. After confirming your image size, use tape or a pencil to mark the distance (c) from the
top of the image area on the board to the bottom of the wall plate.
9. Align the line (horizontal) on the template sheet with the (c) mark, then align the
center line on the template sheet with the center of the image area. Follow the
instructions on page 24 to install the projector.
Wall plate
Projection
surface
Offset value for the position of the
center of the screen and the center of
the wall plate
Distance from wall to
projection surface
2.8 in. (70.5 mm)
8.6 in.
(218 mm)
Height of
projected
image
4.0 in. (100 mm)
1 in. (25 mm)
0.8 in. (20 mm)
1.2 in. (30.6 mm)
4.7 in. (120 mm)
18
When the diagonal image size is less than 75 inches, mount the 3-axis adjustment unit at the position marked
with a stamp.
Distance from projection surface to wall plate
The distance (c) from the projection surface to the wall plate is the number given when the vertical slide is set
to the base position, as shown below.
Match the notch on the wall mount to the position of the stamp on the wall plate.
The measurements may differ depending on the location where you place the
projector.
When projecting in Tele, the quality of the projected images may decrease.
When using BrightLink 595Wi/595Wi+ to project images at a 4:3 aspect ratio, the
images are resized automatically and the quality of the projected images may
decrease.
Base position
Stamp on plate
Notch on mount arm
19
English
Installation Measurements in Inches for BrightLink 595Wi/595Wi+
Diagonal
image
size
(S)
16:10 WXGA 4:3 XGA 16:9 Widescreen
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance (a)
Slider
scale
mark
(b)
Distance
from top of
image to
wall plate
(c)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance (a)
Slider
scale
mark
(b)
Distance
from top of
image to
wall plate
(c)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Slider
scale
mark
(b)
Distance
from top
of image
to wall
plate (c)
53” ——
78.7 42.4 31.8 2.5 5.9 6.9
54” ——
79.4 43.2 32.4 2.7 6.1 7.0
55” ——
80.1 44.0 33.0 3.0 6.4 7.1
56” ——
80.8 44.8 33.6 3.3 6.7 7.2
57” ——
81.5 45.6 34.2 3.6 7.0 7.3
58” ——
82.3 46.4 34.8 3.8 7.3 7.5
59” ——
83.0 47.2 35.4 4.1 7.6 7.6 77.5 51.4 28.9 2.6 6.0 8.5
60”
78.7 50.9 31.8 2.5 5.9 6.9 83.7 48.0 36.0 4.4 7.8 7.7 78.1 52.3 29.4 2.9 6.3 8.7
61”
79.3 51.7 32.3 2.7 6.1 7.0 84.4 48.8 36.6 4.7 8.1 7.8 78.7 53.2 29.9 3.1 6.5 8.8
62”
79.9 52.6 32.9 3.0 6.4 7.1 85.1 49.6 37.2 5.0 8.4 7.9 79.3 54.0 30.4 3.4 6.8 8.9
63”
80.6 53.4 33.4 3.2 6.6 7.2 85.8 50.4 37.8 5.2 8.7 8.0 80.0 54.9 30.9 3.6 7.0 9.1
64”
81.2 54.3 33.9 3.4 6.9 7.3 86.6 51.2 38.4 5.5 8.9 8.2 80.6 55.8 31.4 3.9 7.3 9.2
65”
81.8 55.1 34.4 3.7 7.1 7.4 87.3 52.0 39.0 5.8 9.2 8.3 81.2 56.7 31.9 4.1 7.6 9.3
66”
82.5 56.0 35.0 3.9 7.4 7.5 88.0 52.8 39.6 6.1 9.5 8.4 81.8 57.5 32.4 4.4 7.8 9.5
67”
83.1 56.8 35.5 4.2 7.6 7.6 88.7 53.6 40.2 6.3 9.8 8.5 82.5 58.4 32.9 4.6 8.0 9.6
68”
83.7 57.7 36.0 4.4 7.8 7.7 89.4 54.4 40.8 6.6 10.0 8.6 83.1 59.3 33.3 4.9 8.3 9.7
69”
84.4 58.5 36.6 4.7 8.1 7.8 90.2 55.2 41.4 6.9 10.3 8.8 83.7 60.1 33.8 5.1 8.5 9.9
70”
85.0 59.4 37.1 4.9 8.3 7.9 90.9 56.0 42.0 7.2 10.6 8.9 84.3 61.0 34.3 5.4 8.8 10.0
71”
85.6 60.2 37.6 5.1 8.6 8.0 91.6 56.8 42.6 7.4 10.9 9.0 85.0 61.9 34.8 5.6 9.1 10.2
72”
86.3 61.1 38.2 5.4 8.8 8.1 92.3 57.6 43.2 7.7 11.1 9.1 85.6 62.8 35.3 5.9 9.3 10.3
73”
86.9 61.9 38.7 5.6 9.1 8.2 93.0 58.4 43.8 8.0 11.4 9.2 86.2 63.6 35.8 6.1 9.6 10.4
74”
87.5 62.8 39.2 5.9 9.3 8.3 93.8 59.2 44.4 8.3 11.7 9.4 86.8 64.5 36.3 6.4 9.8 10.6
75”
88.2 63.6 39.7 6.1 6.1 8.4 94.5 60.0 45.0 8.5 8.5 9.5 87.5 65.4 36.8 6.6 6.6 10.7
76”
88.8 64.4 40.3 6.4 6.4 8.5 95.2 60.8 45.6 8.8 8.8 9.6 88.1 66.2 37.3 6.9 6.9 10.8
20
* Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
77” 89.5 65.3 40.8 6.6 6.6 8.6 95.9 61.6 46.2 9.1 9.1 9.7 88.7 67.1 37.8 7.1 7.1 11.0
78”
90.1 66.1 41.3 6.9 6.9 8.8 96.6 62.4 46.8 9.4 9.4 9.8 89.3 68.0 38.2 7.4 7.4 11.1
79”
90.7 67.0 41.9 7.1 7.1 8.9 97.4 63.2 47.4 9.7 9.7 10.0 90.0 68.9 38.7 7.6 7.6 11.2
80”
91.4 67.8 42.4 7.3 7.3 9.0 98.1 64.0 48.0 9.9 9.9 10.1 90.6 69.7 39.2 7.9 7.9 11.4
81”
92.0 68.7 42.9 7.6 7.6 9.1 98.8 64.8 48.6 10.2 10.2 10.2 91.2 70.6 39.7 8.1 8.1 11.5
82”
92.6 69.5 43.5 7.8 7.8 9.2 99.5 65.6 49.2 10.5 10.5 10.3 91.8 71.5 40.2 8.4 8.4 11.6
83”
93.3 70.4 44.0 8.1 8.1 9.3 100.2 66.4 49.8 10.8 10.8 10.4 92.5 72.3 40.7 8.6 8.6 11.8
84”
93.9 71.2 44.5 8.3 8.3 9.4 100.9 67.2 50.4 11.0 11.0 10.5 93.1 73.2 41.2 8.9 8.9 11.9
85”
94.5 72.1 45.0 8.6 8.6 9.5 101.7 68.0 51.0 11.3 11.3 10.7 93.7 74.1
41.7
9.1 9.1 12.0
86”
95.2 72.9 45.6 8.8 8.8 9.6 102.4 68.8 51.6 11.6 11.6 10.8 94.3 75.0
42.2
9.4 9.4 12.2
87”
95.8 73.8 46.1 9.1 9.1 9.7 103.1 69.6 52.2 11.9 11.9 10.9 95.0 75.8
42.7
9.6 9.6 12.3
88”
96.4 74.6 46.6 9.3 9.3 9.8 103.8 70.4 52.8 12.1 12.1 11.0 95.6 76.7
43.1
9.9 9.9 12.5
89”
97.1 75.5 47.2 9.5 9.5 9.9 96.2 77.6
43.6
10.2 10.2 12.6
90”
97.7 76.3 47.7 9.6 9.6 10.0 96.8 78.4
44.1
10.4 10.4 12.7
91”
98.3 77.2 48.2 10.0 10.0 10.1 97.5 79.3
44.6
10.7 10.7 12.9
92”
99.0 78.0 48.8 10.3 10.3 10.2 98.1 80.2 45.1 10.9 10.9 13.0
93”
99.6 78.9 49.3 10.5 10.5 10.3 98.7 81.1 45.6 11.2 11.2 13.1
94”
100.3 79.7 49.8 10.8 10.8 10.4 99.3 81.9 46.1 11.4 11.4 13.3
95”
100.9 80.6 50.3 11.0 11.0 10.5 100.0 82.8 46.6 11.7 11.7 13.4
96”
101.5 81.4 50.9 11.3 11.3 10.6 100.6 83.7 47.1 11.9 11.9 13.5
97”
102.2 82.3 51.4 11.5 11.5 10.7 101.2 84.5 47.6 12.2 12.2 13.7
98”
102.8 83.1 51.9 11.7 11.7 10.9
99”
103.4 84.0 52.5 12.0 12.0 11.0
100”
104.1 84.8 53.0 12.2 12.2 11.1
Diagonal
image
size
(S)
16:10 WXGA 4:3 XGA 16:9 Widescreen
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance (a)
Slider
scale
mark
(b)
Distance
from top of
image to
wall plate
(c)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance (a)
Slider
scale
mark
(b)
Distance
from top of
image to
wall plate
(c)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Slider
scale
mark
(b)
Distance
from top
of image
to wall
plate (c)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116

Epson BrightLink 595Wi Guide d'installation

Catégorie
Projecteurs
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues