Presenza 77315 Guide d'installation

OWNER’S MANUAL

MANUEL DE L’UTILISATEUR

MANUAL DEL USUARIO

QL117KG

Rev. 20210716

STEEL UTILITY SINK

ÉVIER UTILITAIRE EN ACIER

FREGADERO DE ACERO

A LL- I N - O N E

TOUT-EN-UN

TODO EN UNO

QL117KG

ENGLISH

2

Table of Contents

Safety Information ................. 2

Warranty

One Year Limited Warranty .......... 3

Warranty Claim Procedure .......... 3

Pre-Installation

Tools/Materials Required ........... 4

Parts Required ................... 4

Package Contents ................ 5

Installation ....................... 6

Maintenance

Cartridge Replacement ........... 14

Care and Cleaning

Utility Sink ..................... 15

Cabinet ........................ 15

Service Parts ..................... 16

MANUEL DE L'UTILISATEUR ......... 17

MANUAL DEL USARIO .............. 32

Safety Information

DANGER: Always wear safety goggles and gloves in order to avoid personal injury.

READ AND SAVE THESE INSTRUCTIONS

1. Unpack and inspect this product for chips, scratches, cracks, dents, and scuff marks. Do not install

this product if any damages or defects are identied.

2. Use this product only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer.

3. Installation work and plumbing must be done by qualied person(s) in accordance with all

applicable codes and standards.

4. Protect the entire surface during installation.

CONGLOMKB.COM

Please contact [email protected] or 1-877-333-0098 for further assistance.

ENGLISH

3

Warranty

ONE YEAR LIMITED WARRANTY

A thorough inspection must be made before installation and any damage must be promptly reported. Conglom Inc. will not be

liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation.

Conglom Inc. warrants this product to be free from defects in materials or workmanship for one (1) year from the date of

purchase. Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to us for all

warranty claims.

This warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed

following the manufacturer’s instructions. It does not apply in the event of product damage due to the use of other

than genuine replacement parts, (Replacement parts may be obtained by e-mail at [email protected] or by calling

1-877-333-0098 between 8:30 am - 5:00 pm EST) installation error, abuse, misuse or improper care and maintenance

(whether performed by a plumber, contractor, service provider or member of the purchaser’s household). The warranty

excludes damage due to aggressive air or water conditions, harsh or abrasive cleaners and/or materials.

Under no circumstance shall Conglom Inc. be held liable for personal injury or property damage resulting from improper

installation or use of this product. Conglom Inc. will not be held liable for inconvenience caused by loss of use of this product,

costs incurred for labour or materials, removal and installation of replacement units, or any other incidental or consequential

damages. Costs relating to obtaining access for repair or replacement are the responsibility of the user.

Our obligation shall be limited to the repair or replacement of a unit (at our discretion) that may prove, by our sole

examination, to be defective under normal use and service during the warranty period.

Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty. These

non-warrantable items include, but are not limited to:

- Improper installation not in accordance with manufacturer’s instructions.

- Dents and/or scratches incurred during shipping, handling, or installation.

- Change in colour or nish due to chemical usage.

- Damage caused by failure to follow care and cleaning guidelines, including damage caused by the use of

abrasive cleaners.

- Alterations made to the unit by the purchaser or installer.

- Damage caused by accidental impact, re, ood, freezing, and normal wear.

- Bends and warping caused by forced connections, overtightened ttings, and inadequate support during

installation.

- Damage caused by use of chlorine-based cleaners.

This warranty does not extend to commercial and institutional installation or use.

WARRANTY CLAIM PROCEDURE

If a claimable defect occurs or replacement parts are needed, please contact our customer service team at

[email protected] or 1-877-333-0098 (8:30 am - 5 pm, EST, Monday - Friday).

Before you make your call, please ensure that you have:

- Model number or description.

- Proof of sale.

- Details regarding the defect and/or part number.

- Name(s) and address(es) of the owner and/or installer.

QL117KG

ENGLISH

4

Pre-Installation

TOOLS/MATERIALS REQUIRED (NOT SUPPLIED)

Adjustable

wrench

Needle

nose pliers

Phillips

screwdriver

Utility knife Pipe wrench Sealant

Hacksaw Carpenter's level Hex key

Safety gloves Safety goggles Electric drill

Blanket/

Large Cloth Pencil

PARTS REQUIRED (NOT SUPPLIED)

Tail pipe P-Trap Supply lines

CONGLOMKB.COM

Please contact [email protected] or 1-877-333-0098 for further assistance.

ENGLISH

5

Pre-Installation (continued)

PACKAGE CONTENTS

Carefully check the utility cabinet for damage and/or missing parts prior to installation. If there is any

damage or if you are missing parts, do not proceed with the installation. Report damage and/or missing

parts immediately to our customer service team at [email protected] or 1-877-333-0098 (Service

available in English and French, Monday - Friday from 8:30 am - 5:00 pm EST). Please do not dispose of

packaging before you are satised with your new utility cabinet.

A1 A2 A4

A5

C

A3

BD E

F

G G2 I

A6 A7

H

Part Description Quantity Part Description Quantity

A1 Bottom Panel 1 D Faucet 1

A2 Left Side Panel 1 E Strainer Basket 1

A3 Right Side Panel 1 FStrainer Assembly 1

A4 Top Panel 1 G Handle 2

A5 Brace 2 G2 Handle Screws 4

A6 Left Door 1 H Door Hinge

(attached to doors)

4

A7 Right Door 1 I Screws 32

C Sink 1

QL117KG

ENGLISH

6

Installation

CABINET COMPONENTS

A2

A4

A6

A7

A5

A3

A1

Fig.1

CONGLOMKB.COM

Please contact [email protected] or 1-877-333-0098 for further assistance.

ENGLISH

7

Installation (continued)

INSTALLATION OF SIDE PANELS, BOTTOM PANEL AND LEG POSTS

NOTE: When assembling cabinet, place all parts on a soft,

protective surface. Use of an electric screwdriver can speed

up assembly. Please ensure the torque setting is adjusted

such that the screws are not stripped during installation.

DANGER:

Always wear safety

goggles and gloves in order to

avoid personal injury.

- Install bottom panel (A1) into the slot of the side panels

(A2, A3). Ensure hinge hardware is along upper side.

A2

A3

A1

Hinge hardware

Fig.2

- Install leg posts (B) in place.

I

B

Fig.3

- Install screws to nish

securing bottom panel to

side panels.

Fig.4

QL117KG

ENGLISH

8

Installation (continued)

TOP PANEL INSTALLATION

- Place top panel (A4) on side boards and install into place. Ensure door stopper edge is oriented

towards bottom of cabinet and the cosmetic side of top panel is facing the front of the cabinet.

A4

I

A2 A3

A4

Side with door stopper edge

Door stopper edge

Fig. 5

INSTALLATION OF REAR BRACES

- Gently lift cabinet up.

Fig. 6

CAUTION:

Do not rest or bump the

leveling legs on the side as this may

cause them to detach or break.

CONGLOMKB.COM

Please contact [email protected] or 1-877-333-0098 for further assistance.

ENGLISH

9

Installation (continued)

- Install rear braces (A5) in place.

A4

A3

A2

A5

Ensure open face of rear

braces (A5) are facing the

outside of the cabinet.

I

Fig. 7

DOOR HANDLE INSTALLATION

NOTE: Do not overtighten

G

G2

Fig. 8

QL117KG

ENGLISH

10

Installation (continued)

DOOR INSTALLATION

- Hook and snap door hinges in place.

You will hear a click sound when

the hinges are properly engaged.

A2

A6

Fig. 9

DOOR POSITION ADJUSTMENT

If the doors need to be repositioned, the hinges can be adjusted to ensure a precise t with the cabinet.

Fig. 10A

- The lateral adjustment

screw adjusts the door

orientation left and right.

Fig. 10B

- The horizontal adjustment

screw adjusts the door

orientation front and back.

Fig. 10C

- The vertical adjustment screws

adjust the door orientation up

and down. Loosen screws, adjust

height and then retighten. The

two screws closest to the door

may be removed.

CONGLOMKB.COM

Please contact [email protected] or 1-877-333-0098 for further assistance.

ENGLISH

11

Installation (continued)

INSTALLING THE FAUCET

- Connect the sprayer head (1) to the sprayer

head connector (2).

- Remove the gasket (3), metal washer (4),

and retaining nut (5) from the faucet.

- Install the faucet through the hole

in the sink.

- From underneath, secure the faucet to the

sink with the gasket (3), metal washer (4),

and retaining nut (5).

- Tighten the retaining nut (5) by hand until

it is snug. Use a wrench to tighten it down.

Gently tighten the two screws on the

retaining nut. Do not overtighten.

- Hand-tighten the hose (6) to the faucet

outlet (7). Tighten the ttings using two

wrenches. Hold the faucet outlet (7) steady

with a wrench while turning the hose tting

with another wrench until it is snug.

NOTE: Failing to use two wrenches can damage the

faucet. Do not overtighten.

- Push the sprayer head (1) into the faucet

neck. Install the counterweight (8) a couple

of inches from the bottom of the hose on

the side closest to the sprayer head (1).

There should be no slack in the hose and it

should retract freely.

- Connect the water supply lines (not

supplied) to the faucet.

- This faucet is equipped with standard

1/2" NPS male thread connectors that are

compatible with standard 1/2" FIP water

supply lines.

Counterweight (8)

Hose (6)

Faucet outlet (7)

Faucet body

Metal Washer (4)

Gasket (3)

Retaining nut (5) Screws

Sink

Sprayer

head (1)

Sprayer head

connector (2)

Water Connectors

1/2" NPS thread

1/2" FIP water supply

line compatible

(not supplied)

Hose

Faucet outlet

Fig. 12

Fig. 13

QL117KG

ENGLISH

12

Installation (continued)

INSTALLING THE STRAINER

- Apply plumbing putty or silicone

sealant to the top side of the

drain opening.

- Insert the strainer body (1) into the

drain opening and press it down until it

is evenly seated.

- Assemble the rubber gasket (2), ber

washer (3) and strainer locknut (4) onto

the strainer body (1) from underneath

the sink. Hand tighten the strainer

locknut (4) until it is snug. Do not

overtighten.

- Insert the plastic ange (5) into the

ange-end of the tailpipe (6) (not

supplied) then secure the tailpipe to

the strainer body using the connecting

nut (7). Tighten the connecting nut (7)

until it is snug. Do not overtighten.

- Remove excess sealant from around

the drain opening.

Strainer Body (1)

Sealant

Sink

Rubber Gasket (2)

Fiber Washer (3)

Strainer Locknut (4)

Plastic Flange (5)

Tailpipe (6)

(not supplied)

Connecting Nut (7)

Strainer Basket

Fig. 14

CONGLOMKB.COM

Please contact [email protected] or 1-877-333-0098 for further assistance.

ENGLISH

13

Installation (continued)

MOUNTING THE UTILITY SINK

- Carefully place a bead of sealant all around

the top of the cabinet (A).

- Ease the sink (C) into the cabinet (A). Ensure

that it is placed evenly and is centered on

the cabinet (A). Wipe off any excess sealant.

Use masking tape to hold the sink (C) in

place until the sealant dries.

SEALANT

Sink (C)

Faucet (D)

Cabinet (A)

PLACEMENT

- Push the cabinet (A) against the wall. Position cabinet as desired. If required, level it by adjusting

the four leveling legs and checking the alignment of the sink (C) using a carpenter’s level.

IMPORTANT: Secure the cabinet to the wall using hardware best suited for your wall type. Failing to

do so could result in property damage or personal injury.

Use silicone sealant to seal the sink to the wall and any adjacent surfaces to keep those surfaces dry.

Failing to do so could result in moisture damage.

DRAINAGE

- The tailpipe (not supplied) previously installed to the drain can now be connected to your

household plumbing. In some cases, your household plumbing will have to be modied to ensure

proper drainage. If so, please consult a licensed plumber to complete needed modications.

SUPPLY LINES (NOT INCLUDED)

- Connect the supply lines to your home’s water

supply as per manufacturer’s instructions.

- Open the hot and cold water supply valves and

check to make sure they have been installed to

appropriate inlet ports. Check for leaks. Run hot and

cold water uninterrupted for about one minute to

remove any residue from the lines.

QL117KG

ENGLISH

14

Maintenance

CARTRIDGE REPLACEMENT

- Turn off the water supply to the faucet.

- Unscrew the handle lever (1). Loosen the set screw (2) with the hex key and remove the

handle body (3).

- Gently unscrew the decorative cap (4) and retaining nut (5).

- Pull the cartridge (6) out of the faucet body (7) and replace it with a new ceramic cartridge. Ensure

new cartridge is seated properly with the locating pins in appropriate place.

- Secure the cartridge in place using the retaining nut (5).

- Gently tighten the retaining nut (5) using a wrench. Do not overtighten.

- Reinstall the decorative cap (4). Slide the handle body (3) back onto the cartridge and make sure it

rotates freely. Secure the handle body (3) in place using the set screw (2) and reinstall the handle

lever (1).

- Turn the water supply to the faucet back on.

- Operate the faucet to make sure everything works correctly and check for leaks.

Handle Lever (1)

Decorative Cap (4)

Retaining Nut (5)

Cartridge (6)

Handle Body (3)

Faucet Body (7)

Set Screw (2)

O-Ring (8)

CONGLOMKB.COM

Please contact [email protected] or 1-877-333-0098 for further assistance.

ENGLISH

15

Care and Cleaning

Your utility sink is manufactured with the highest grade materials and will provide you many years of

enjoyment with the proper care.

SINK

Do: Do Not:

- After use, always rinse your sink with tap water

to dilute and remove deposits.

- Towel dry after use whenever possible to

prevent water spots. Should water spots occur,

clean with a mild solution of vinegar and water

followed by a thorough rinse.

- Use liquid soap, a general household cleaner,

or a weak solution of vinegar and water for

regular cleaning.

- Only use plastic scouring pads recommended for

use in stainless steel sinks, and only use them in

the bowl of the sink. Scrub in the direction of the

satin nish lines.

- Do not allow any food, detergent, soap or grease

to dry or sit for extended periods of time on the

surface of the sink.

- Never use abrasive cleaning products, as they

will dull and scratch the nish.

- Do not use scouring pads on the deck, as they

will dull the nish.

- Never use steel wool pads or leave steel/cast

iron pans in your sink for extended periods of

time, as they will leave iron particles on the sink,

which can cause corrosion.

- Never use chlorine-based cleaners in your

new sink, they could lead to rust spots and

discolouration. If you must use them, rinse

sink thoroughly with fresh water immediately

after use.

- If any chemicals or glue make contact with the

sink during installation, wipe clean and rinse

thoroughly with fresh water.

SCRATCH, SPOT, AND BLEMISH REMOVAL AND SURFACE RESTORATION:

Little rust spots and blemishes that periodically appear in the sink are typically the result of the steel interacting with the

chemicals found in the vast spectrum of substances that sinks are commonly exposed to. They may also get transferred from

other objects placed or left in the sink. Scratches are the result of regular wear and tear.

To remove scratches, spots, and blemishes from the sink, rub them with a non-metallic scouring pad (e.g. Scotch-Brite®)

combined with a mild abrasive cleaner (e.g. Vim® or Barkeeper’s Friend®). Always rub the surfaces in the direction of the grain of

the steel. When nished, rinse the sink with water and dry it with a towel to allow the sink to form a protective outer layer. This

procedure can also be used to renew all of the surfaces of the sink.

CABINET

Do: Do Not:

- Remove dust and dirt with a soft, damp cloth

using mild soap and warm ltered water.

- Clean grease and stains with mild soap that

contains emulsiers. Immediately rinse with

warm ltered water afterwards.

- Do not allow your cabinet surface to come into

contact with any harsh cleaning products.

- Use caution when using sharp instruments that

may fall and scratch the surface.

QL117KG

ENGLISH

16

Service Parts

If you are missing parts or require replacement parts, please contact our customer service team at

[email protected] or 1-877-333-0098 (Service available in English and French, Monday - Friday from

8:30am - 5pm EST). Identify the required part(s) and have the part number(s) ready.

A B C

D E

GF

HI

Part Description Code Quantity

A Leg Posts QHL221B 4

B Strainer Basket QHL177 1

CStrainer Assembly QHL176 1

D Handle QHL225 2

E Handle Screws QHL227 4

FDoor Hinge QHL228B 4

G Screws QHL230 32

H Sprayer Head QHL272 1

I Ceramic Cartridge QHL216 1

CONGLOMKB.COM

Veuillez contacter [email protected] ou 1-877-333-0098 pour toute assistance supplémentaire.

FRANÇAIS

17

Table des matières

OWNER'S MANUAL ................. 2

Consigne de sécurité .............. 17

Garantie

Garantie limitée d'un an ........... 18

Procédure de réclamation ......... 18

Préinstallation

Outils/Matériaux requis ........... 19

Pièces requises ................. 19

Contenu de l'emballage ........... 20

Installation ...................... 21

Entretien

Remplacement de la cartouche ..... 29

Soin et nettoyage

Évier .......................... 30

Armoire ....................... 30

Pièces de rechange ............... 31

MANUAL DEL USARIO .............. 32

Consigne de sécurité

AVERTISSEMENT: Toujours porter des lunettes et des gants de sécurité pendant l’installation

an d’éviter les blessures.

LIRE ET CONSERVER CES DIRECTIVES

1. Vérier soigneusement l’unité avant l’installation pour vous assurer qu’elle ne comporte aucun

dommage. Après avoir déballé votre unité, vérier s’il y a des rayures, des ssures, des bosses ou

des éraures. Si des dommages sont notés, ne pas installer.

2. Cet appareil ne peut être utilisé autrement que pour l’usage prévu par le fabricant. Consulter le

fabricant pour toutes questions concernant l’appareil.

3. Votre installation doit être conforme à tous les codes de bâtiment locaux pour la plomberie. Veiller à

ce qu’un ouvrier qualié effectue ou approuve votre installation de plomberie.

4. Protéger la surface lors de l’installation.

QL117KG

FRANÇAIS

18

Garantie

GARANTIE LIMITÉE D'UN AN

Inspecter minutieusement le produit avant l’installation et signaler tout dommage sans délai. Nous ne serons pas

responsables des défaillances ou des dommages qui auraient dû être découverts ou évités par une inspection adéquate et

des essais avant l’installation.

Conglom Inc. garantit ce produit contre tout défaut dans les matériaux ou la fabrication, pour une période d’un (1) an à

compter de la date de l’achat. Une preuve d’achat (facture d’achat originale) du consommateur/acheteur original devra

accompagner toute réclamation faite à Conglom Inc.

Cette garantie est non transférable et sera nulle si l’unité est enlevée de son installation initiale ou si elle n’est pas installée

suivant les spécications du fabricant. Elle ne s’applique pas dans l’éventualité de dommages causés au produit suite à

l’utilisation de pièce(s) de rechange autre que les pièces originales Conglom Inc., (les pièces de rechange peuvent être

obtenus en nous écrivant un courriel à [email protected] ou en appellant au 1-877-333-0098 entre 8h30 et 17h00,

H.N.E.) une erreur d’installation, l’abus, l’utilisation ou l’entretien incorrecte et le service incorrects (qu’ils soient effectués

par un plombier, un entrepreneur, une entreprise de service ou un membre de la famille de l’acheteur). La garantie exclut les

dommages causés par des conditions agressives d’air ou d’eau, des nettoyants ou des matériaux rudes et/ou abrasifs.

Nous ne pouvons en aucun cas être tenus responsables pour toute blessure corporelle ou tout dommage matériel résultant

d’une mauvaise installation ou utilisation de ce produit. Nous ne serons pas tenues responsables de l’incapacité d’utiliser

cette unité, des inconvénients, des coûts encourus pour la main d’œuvre, des matériaux, de l’enlèvement et de l’installation

des unités de remplacement ou d’aucun autre dommage causé par un incident ou accessoire. Les coûts encourus pour

obtenir l’accès pour la réparation ou le remplacement sont la responsabilité de l’utilisateur.

Nos obligations se limitent à la réparation ou au remplacement de l’unité (selon notre choix) qui peut s’avérer, selon notre

examen unique, être défectueuse sous l’utilisation et le service normaux pendant la période de garantie. Nous pouvons

émettre un crédit au montant de la valeur de la facture du produit défectueux (ou d’un pourcentage de ce montant selon

l’usure) tenant lieu de la réparation ou du remplacement.

Toute défectuosité de l’unité qui ne peut être liée à un défaut de matériel ou de fabrication n’est pas couvert par cette

garantie. Ces conditions non garanties incluent, mais ne se limitent pas aux suivantes :

- Une mauvaise installation non conforme aux instructions du fabricant.

- Les bosselures, bosses et rayures causées pendant l’expédition, la manutention ou l’installation.

- Changement de la couleur ou du ni en raison de l’usage d’un produit chimique.

- Les dommages causés par le non-respect des directives de soin et de nettoyage, y compris les dommages causés

par l’utilisation de produits nettoyants abrasifs.

- Toute modication apportée à l’unité par l’acheteur ou l’installateur.

- Dommages en raison d’un impact accidentel, du feu, d’une inondation, du gel et de l’usure normale.

- Courbures et déformations provoquées par des raccordements forcés, des xations trop serrées et un support

inadéquat pendant l’installation.

- Dommages causés par l’utilisation de produits nettoyants à base de chlore.

Cette garantie ne s’applique pas à l’utilisation ou l’installation à des ns commerciales ou institutionnelles.

PROCÉDURE DE RÉCLAMATION

Si un défaut couvert par la garantie se produit ou que vous avez besoin des pièces de rechange, contacter notre service à la

clientèle au [email protected] ou au 1-877-333-0098 (lundi au vendredi, 8h30 à 17h, H.N.E.).

Avant d’appeler, veuillez-vous assurer d’avoir en main :

- Numéro de modèle ou une description.

- La preuve d’achat.

- Les détails concernant le défaut et/ou le numéro de la pièce de rechange.

- Le nom et l’adresse du propriétaire et/ou de l’installateur.

CONGLOMKB.COM

Veuillez contacter [email protected] ou 1-877-333-0098 pour toute assistance supplémentaire.

FRANÇAIS

19

Préinstallation

OUTILS/MATÉRIEL REQUIS (NON INCLUS)

Clé Pinces à

bec eflé

Tournevis

Phillips

Couteau

tout usage Clé à tuyau Mastic

Scie à métaux Niveau Clé hexagonale

Gants

de sécurité

Lunettes

de sécurité

Tournevis

électrique

Couverture/

Grand tissu Crayon

PIÈCES REQUISES (NON INCLUSES)

Tuyau de vidange Siphon-P Tuyaux

d'alimentation

QL117KG

FRANÇAIS

20

Préinstallation (suite)

CONTENU DE L'EMBALLAGE

Vérier soigneusement que l’unité ne comporte aucun dommage ou pièces manquantes avant

l’installation. S’il y a des dommages ou s’il manque des pièces, ne pas procéder à l’installation.

En cas de dommages ou de pièces manquantes, communiquer avec le service à la clientèle au

[email protected] ou 1 877 333-0098 (service en anglais et français, du lundi au vendredi, 8 h 30 et

17 h, HNE). Ne pas vous débarrasser de l’emballage avant d’être satisfait de ce produit.

A1 A2 A4

A5

C

A3

BD E

F

G G2 I

A6 A7

H

Pièce Description Quantité Pièce Description Quantité

A1 Panneau inférieur 1 D Robinet 1

A2 Panneau latéral gauche 1 E Panier de crépine 1

A3 Panneau latéral droit 1FAssemblage de la crépine 1

A4 Panneau supérieur 1 G Poignée 2

A5 Support de montage 2 G2 Vis de poignée de porte 4

A6 Porte de gauche 1 H Charnière de porte

(attachée aux portes)

4

A7 Porte de droite 1 I Vis 32

BPattes 4

C Évier 1

La page charge ...

Presenza 77315 Guide d'installation

Presenza 77315 Guide d'installation

dans d''autres langues

Autres documents