NAPOLEON NEFB30GL Mode d'emploi

EN

W415-2166 / B / 10.17.18

FR

PG

27

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212  Fax (705)720-9081  www.napoleonﬁ replaces.com [email protected]

SAFETY INFORMATION

!

WARNING

If the information in these instructions

are not followed exactly, a ﬁ re may result

causing property damage, personal injury

or loss of life.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

$10.00

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No.46 / UL 1278 CSA STANDARD

EF30

ELECTRIC FIREPLACE

NEFB30GL

ELECTRIC FIREPLACE

W415-2166 / B / 10.17.18

2

EN

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INTRODUCTION 3

1.1 DIMENSIONS 4

1.2 LISTING APPROVALS 4

1.3 GENERAL INSTRUCTIONS 5

1.4 LABEL LOCATION 6

2.0 LOCATING APPLIANCE 7

2.1 UNPACKING AND TESTING APPLIANCE 7

2.2 GROUNDING APPLIANCE 8

3.0 INSTALLATION 9

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 10

3.2 MINIMUM MANTEL CLEARANCES 10

3.3 NEW CONSTRUCTION OR RENOVATION 11

3.4 INSTALLING THE APPLIANCE 11

3.5 THERMOSTAT AND THERMAL SENSOR INSTALLATION 11

3.6 HARD-WIRE INSTALLATION 12

3.7 WIRING DIAGRAM 13

4.0 FRAMING 14

5.0 FINISHING 15

5.1 HEARTH 15

5.2 COLD CLIMATE INSTALLATION 15

5.3 FINISHING CHECKLIST 15

6.0 OPERATING INSTRUCTIONS 16

6.1 OPERATING BY REMOTE CONTROL 17

6.2 CRYSTAL EMBER PLACEMENT 18

6.3 LED / REMOTE RECEIVER / THERMOSTAT REPLACEMENT 19

6.4 FUSE REPLACEMENT 19

7.0 REPLACEMENT PARTS 20

7.1 REPLACEMENT PARTS DIAGRAM 21

8.0 TROUBLESHOOTING 22

9.0 WARRANTY 23

10.0 SERVICE HISTORY 24

11.0 NOTES 25

W415-2166 / B / 10.17.18

3

EN

1.0 INTRODUCTION

!

WARNING

C

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF

CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate

appliance according to operating instructions could cause ﬁ re or injury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before

servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance

and are kept clean. The appliance should be inspected before use and at least annually by a qualiﬁ ed

service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and

other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been

dropped or damaged in any manner. Return appliance to authorized service facility for examination,

electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord

away from trafﬁ c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or ﬁ re, or damage the appliance.

• To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or

relocatable power tap (outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or other electronic components.

W415-2166 / B / 10.17.18

4

EN

Rating

Plate &

Serial

Number

Power Cord and Thermostat

32

1

/

4

”

10

3

/

4

”

32”

Heater vents - DO NOT COVER

10

”

30”

29

1

/

2

”

26

1

/

2

”

!

WARNING

HEATER VENTS AND AIR OPENINGS CAN NOT

BE COVERED IN ANY CIRCUMSTANCES.

1.1 DIMENSIONS

This appliance has been tested in accordance with the CSA Standards for ﬁxed and location-dedicated

electric room appliances in the United States and Canada. If you need assistance during installation, please

contact your local dealer.

Model Number NEFB30GL

Description Electric Appliance

Voltage 120V AC

Watts MAX 1500W

Lamp LED

Appliance Width 30" (762mm)

Appliance Height 32 1/4" (820mm)

Appliance Depth 10 3/4" (273mm)

Net Weight 79 lbs (36kg)

Gross Weight 89 lbs (41kg)

NOTE: This appliance must be electrically wired and

grounded in accordance with local codes or, in the absence

of local codes, with National Electric Code ANSI/NFPA

70-latest edition or the Canadian Electric Code, CSA C22.1

as appropriate.

1.2 LISTING APPROVALS

W415-2166 / B / 10.17.18

5

EN

1.3 GENERAL INSTRUCTIONS

A.

Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

B.

The appliance may emit a slight, harmless odour when ﬁ rst used. This odour is normal and it is caused

by the initial heating of internal appliance elements and will not occur again.

C.

If your appliance does not emit heat, consult the operation section of this manual for further

information.

D.

Use with a CSA- or UL-certiﬁ ed surge protector.

E.

Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured

homes when installed according to these instructions.

!

WARNING

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE

IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL

ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

RESULT IN A SAFETY HAZARD.

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

POWER SUPPLY CIRCUIT.

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

RECEPTACLE AND FULLY INSERT.

W415-2166 / B / 10.17.18

6

EN

1.4 LABEL LOCATION

W415-2166 / B / 10.17.18

7

EN

2.0 LOCATING APPLIANCE

NOTICE

Minimum clearance of 1" on all sides, back and top must

be maintained at all times. Illustrations throughout these

instructions reﬂect typical installations and are for design

purposes only. Actual installations may vary slightly due to

individual preferences.

Illustrates a variety of ways the appliance may be located

in a room. The appliance may be installed directly on the

ﬂoor (uncarpeted), or raised on a hearth.

TOP VIEW SHOWING APPROVED ROOM

LOCATIONS OF APPLIANCE

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance

operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet.

2.1 UNPACKING AND TESTING APPLIANCE

!

WARNING

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 3 FEET (0.9M) FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE MUST

NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

W415-2166 / B / 10.17.18

8

EN

2.2 GROUNDING APPLIANCE

GROUNDING METHODS

METAL SCREW

(A)

NOT ALLOWED IN CANADA

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

COVER OF

GROUNDED

OUTLET BOX

(C)

(B)

This appliance is for use on 120 volts. The cord has a plug

as shown in (A). An adapter as shown in (C) is available for

connecting three-blade grounding type plugs to two-slot

receptacles. The green grounding plug extending from the

adapter must be connected to a permanent ground such as

a properly grounded outlet box. The adapter should not be

used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove

plug from outlet.

W415-2166 / B / 10.17.18

9

EN

BEFORE INSTALLATION

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high

trafﬁc areas. NOTE: Follow all national and local electrical codes. This appliance can be installed into

either an existing ﬁreplace opening or as new construction / renovation.

EXISTING APPLIANCE INSTALLATION

Thoroughly clean out the existing ﬁreplace and hearth area.

Plan the power supply. If an existing grounded outlet is near the appliance, the power cord can run behind

the appliance. If the cord is not long enough to reach the outlet, a grounded extension cord minimum AWG

No. 14 and rated to a minimum of 1875 watts may be used. If you plan to cut or drill a hole in the existing

ﬁreplace for wiring, it is best to hire a professional to do this step in order to prevent personal injury. To reduce

the risk of ﬁre, do not run the power cord under rugs, carpets, etc. Arrange the power supply cord away from

high trafﬁc areas where it may pose a tripping hazard.

3.0 INSTALLATION

!

WARNING

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE

CORD TO AVOID TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

PERSONAL INJURY. DO NOT RUN CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW

RUGS, RUNNERS OR THE LIKE. ARRANGE CORD AWAY FROM TRAFFIC AREAS AND WHERE IT

WILL NOT BE TRIPPED OVER.

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY

MANNER. DO NOT USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED

OPTIONAL ACCESSORIES. USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR

THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-

SION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE

OR USE GASOLINE OR OTHER FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER

APPLIANCE.

THIS APPLIANCE MUST REMAIN REMOVABLE FROM THE ENCLOSURE. THE APPLIANCE MAY BE

HARD WIRED, BUT IT IS RECOMMENDED THAT IT BE PLUGGED INTO A STANDARD OUTLET USING

THE SUPPLIED POWER CORD. THIS APPLIANCE MUST NOT BE SEALED AROUND THE FRONT

FACING.

APPLIANCE VENTS LOCATED ON THE FRONT AND BACK OF THIS ELECTRIC APPLIANCE CANNOT,

IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE HAZARD.

W415-2166 / B / 10.17.18

10

EN

Sides, back, top 1" (25mm)

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES

THIS APPLIANCE MUST REMAIN REMOVABLE FROM THE ENCLOSURE. THE APPLIANCE MAY BE HARD

WIRED, BUT IT IS RECOMMENDED THAT IT BE PLUGGED INTO A STANDARD OUTLET USING THE

SUPPLIED POWER CORD. THIS APPLIANCE MUST NOT BE SEALED AROUND THE FRONT FACING.

APPLIANCE VENTS LOCATED ON THE FRONT AND BACK OF THIS ELECTRIC APPLIANCE CANNOT,

IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE HAZARD.

!

WARNING

3.2 MINIMUM MANTEL CLEARANCES

The minimum distance from the top of the appliance that the mantel can be installed is 10" (254mm), at any depth.

APPLIANCE

SIDEVIEW

FRONT

GLASS

OPTIONAL

HEARTH

WALL

MANTEL

10”

!

WARNING

RISK OF FIRE, MAINTAIN ALL SPECIFIED AIR SPACE CLEARANCES TO COMBUSTIBLES. FAILURE

TO COMPLY WITH THESE INSTRUCTIONS MAY CAUSE A FIRE OR CAUSE THE APPLIANCE TO

OVERHEAT. ENSURE ALL CLEARANCES (I.E. BACK, SIDE, TOP, VENT, MANTEL, FRONT, ETC.) ARE

CLEARLY MAINTAINED.

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE

HEAT RESISTANT TO PREVENT DISCOLOURATION.

W415-2166 / B / 10.17.18

11

EN

A. Select a location that is not prone to moisture and is located at least 0.9 m or 3 feet away from

combustible materials such as curtains or drapes, furniture, bedding, paper, etc.

B. Place the appliance in selected location to see how it will look in the future.

C. Mark the desired location on the ﬂoor and store appliance in a safe, dry and dust free location.

D. Frame in an opening leaving at least 1/4" (6 mm) around the edge of the appliance. Any new wiring

must be done in compliance with local and national codes and other applicable regulations in order

to reduce the risk of ﬁre, electric shock or other injuries. Therefore, it is strongly recommended that

you hire a professional to complete any such work.

A. Once the site has been prepared, the appliance can be installed.

B. Make sure the main power switch is in the "OFF" position.

C. Plug the appliance into a 15-amp/120 Volt, grounded outlet. Use a CSA or UL approved surge

protector.

D. Push in the appliance so that the trim is against the ﬁnished mantel or wall surface.

3.3 NEW CONSTRUCTION OR RENOVATION

3.4 INSTALLING THE APPLIANCE

3.5 THERMOSTAT AND THERMAL SENSOR INSTALLATION

This appliance has two options for heat control.

First is a thermal controlled sensor, which comes plugged into the appliance beside the main power cord.

This sensor has no user temperature set points, it will turn off the heater when the sensor reaches its pre-set

point, and will only turn the heater back on when it has cooled back down below this set point. On the low

setting (green light) the set point is 16°C/61°F, on medium (orange light) 22°C/72°F and on high (red light)

28°C/82°F. This small sensor can be placed anywhere in the room within the length of the sensor wire, but it

should not be placed near the top or front of the appliance. Placing the sensor too close to the heater area of

the appliance will cause unwanted cycling of the heater.

Second is the option of a wall-mounted thermostat. Napoleon Part # W690-0001, W660-0081, or an equiva-

lent low voltage thermostat.

A wall thermostat can be used in place of the thermal control sensor. You must ﬁrst remove the sensor by un-

plugging it from the right side of the appliance beside the main power cord. Replace the sensor with the wire

harness provided in the manual baggie. Plug it into the appliance and connect the other end to the thermo-

stat. The thermostat should be placed as per the thermostat installation instructions.

W680-0022

Thermo-controlled sensor

5M Temperature Probe (included)

W415-2166 / B / 10.17.18

12

EN

HARDWIRING CONNECTION

If it is necessary to hardwire this appliance, a qualiﬁed electrician may remove the cord connection, and wire

the appliance directly to the house hold wiring.

This appliance must be electrically connected and grounded in accordance with local codes, if hardwired. In

the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the cur-

rent ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

A. Remove cover plate located beside the power cord to reveal the 7/8” wire hole. Discard cover plate,

screws and insert a box connector into the hole.

B. Remove the lower back panel from the appliance to expose wiring.

C. Remove the power cord strain-relief from the side of the appliance and cut the cord where shown

below. This will be the hardwire connection point.

D. Feed the supply wires through the box connector and the grommet.

E. Using wire connectors connect the common (white) wires together, then the hot (black) wires, and

then the ground (green) wires.

F. Ensure the newly connected wires are kept away from the rotating parts and the circuit board, and

re-install the back panel.

NOTE: This appliance must be serviced from the back, leave enough wire so that the appliance can be

removed from the enclosure without disconnecting the power supply wires.

3.6 HARDWIRE INSTALLATION

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

Remove 2 screws on cover plate.

2

3

4

1

Hot Wire

Cut

Power Cord

Final Connection

Common Wire

Ground Wire

Box

Connector

W415-2166 / B / 10.17.18

13

EN

CEILING LIGHT

N

L1

G

3.7 WIRING DIAGRAM

W415-2166 / B / 10.17.18

14

EN

4.0 FRAMING

!

WARNING

RISK OF FIRE!

IN ORDER TO AVOID THE POSSIBILITY OF EXPOSED INSULATION OR VAPOUR BARRIER COMING

IN CONTACT WITH THE APPLIANCE BODY, IT IS RECOMMENDED THAT THE WALLS OF THE

APPLIANCE ENCLOSURE BE “FINISHED” (IE: DRYWALL / SHEETROCK), AS YOU WOULD FINISH

ANY OTHER OUTSIDE WALL OF A HOME. THIS WILL ENSURE THAT CLEARANCE TO

COMBUSTIBLES IS MAINTAINED WITHIN THE CAVITY.

DO NOT NOTCH THE FRAMING AROUND THE APPLIANCE STAND-OFFS. FAILURE TO MAINTAIN

AIR SPACE CLEARANCE MAY CAUSE OVER HEATING AND FIRE. PREVENT CONTACT WITH

SAGGING OR LOOSE INSULATION OR FRAMING AND OTHER COMBUSTIBLE MATERIALS. BLOCK

OPENING INTO THE CHASE TO PREVENT ENTRY OF BLOWN-IN INSULATION. MAKE SURE

INSULATION AND OTHER MATERIALS ARE SECURED.

WHEN CONSTRUCTING THE ENCLOSURE ALLOW FOR FINISHING MATERIAL THICKNESS TO

MAINTAIN CLEARANCES. FRAMING OR FINISHING MATERIAL CLOSER THAN THE MINIMUMS

LISTED MUST BE CONSTRUCTED ENTIRELY OF NON-COMBUSTIBLE MATERIALS. MATERIALS

CONSISTING ENTIRELY OF STEEL, IRON, BRICK, TILE, CONCRETE, SLATE, GLASS OR PLASTERS,

OR ANY COMBINATION THEREOF ARE SUITABLE. MATERIALS THAT ARE REPORTED AS PASSING

ASTM E 136, STANDARD TEST METHOD FOR BEHAVIOUR OF MATERIALS IN A VERTICAL TUBE

FURNACE AT 1382° F (750°C) AND UL763 SHALL BE CONSIDERED NON-COMBUSTIBLE

MATERIALS.

MINIMUM CLEARANCE TO COMBUSTIBLES MUST BE MAINTAINED OR A SERIOUS FIRE HAZARD

COULD RESULT.

THE APPLIANCE REQUIRES A MINIMUM ENCLOSURE HEIGHT. MEASURE FROM THE APPLIANCE

BASE.

IF STEEL STUD FRAMING KITS WITH CEMENT BOARD ARE PROVIDED, OR SPECIFIED IN THE

INSTALLATION INSTRUCTIONS, THEY MUST BE INSTALLED.

IF SPECIFIED IN THE INSTALLATION INSTRUCTION FINISHING MUST BE DONE USING A NON-

COMBUSTIBLE MATERIAL SUCH AS NON-COMBUSTIBLE BOARD, CERAMIC TILE, MARBLE, ETC.

DO NOT USE WOOD OR DRYWALL. ANY FIRE RATED DRYWALL IS NOT ACCEPTABLE

H

E

AD

E

R

29"

[737mm]

31 1/2"

[800mm]

11 3/4"

[298mm]

L

K

J

B

C

B

A

NEFB30GL

B

29" (737mm)

J

50" (1270mm)

K

35 3/8" (898mm)

L

35 3/8" (898mm)

W415-2166 / B / 10.17.18

15

EN

A hearth is NOT necessary but is recommended for aesthetic purposes.

IT IS MANDATORY TO HAVE AN INSULATED WALL BEHIND THE APPLIANCE, WHEN THE

APPLIANCE IS BEING INSTALLED ON AN OUTSIDE WALL OR CHASE.

5.0 FINISHING

5.1 HEARTH

5.2 COLD CLIMATE INSTALLATION

!

WARNING

A. Power supply service must be completed prior to ﬁnishing to avoid reconstruction.

B. Appliance vents and air openings cannot be covered in any circumstances.

5.3 FINISHING CHECKLIST

RISK OF FIRE!

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

DO NOT STRIKE, SLAM OR SCRATCH GLASS. DO NOT OPERATE APPLIANCE WITH GLASS

REMOVED, CRACKED, BROKEN OR SCRATCHED.

FACING AND/OR FINISHING MATERIAL MUST NEVER OVERHANG INTO THE APPLIANCE OPENING.

!

WARNING

W415-2166 / B / 10.17.18

16

EN

6.0 OPERATING INSTRUCTIONS

HIGH LOW TEMP OFF

High

Brightness

Medium

Brightness

Low

Brightness

Light off

After turning the power switch on, the power indicator is red.

First press of the "

" button : the heating element is on "HIGH" mode, two groups of heating elements work

simultaneously while the power is 1500W, indicator is red.

Second press of the button "

": the heating element is on "LOW" mode, one group of heating elements

work while the power is 750W, indicator is blue.

Third press of the button "

": the heating element is on "TEMP" mode. When "TEMP" mode is on, the

appliance automatically sets the room temperature as 25°C. When the room temperature is above 25°C, the

heating element shuts off. When the room temperature is below 22°C, the heating element starts working at

1500W. When the room temperature is between 22-25°C, the heating element starts working at 750W.

Fourth press of the button "

": turns off the heating element.

Press button "

": ﬂame and ember bed work simultaneously in the following sequence:

Press button "

": the ceiling light is switched on. The ﬁrst press gradually increases the brightness of

blue light. The second to fourth press switches lights in sequence of blue, amber and yellow. The ﬁfth press

switches the light to a combination of blue, yellow and amber light. The sixth press shuts off the lights.

W415-2166 / B / 10.17.18

17

EN

NOTE: Make sure your batteries are

fully charged and installed correctly

in your remote control.

6.1 OPERATING BY REMOTE CONTROL

1. Plug in the power cord and turn on the power switch. You will hear the buzzer make

two beep sounds, indicating that the power is turned on. Press the "

" key to start

up the appliance. Flame and ember bed LEDs will turn on with the brightness level set

to the highest as the default, the heating element will be off and the ceiling light will

turn on the color starting to change gradually from bright blue.

2. The “ ” button is the switch for entire appliance, when the appliance is turned off,

press “

”; the appliance is turned on with the same setting as the last time it has

been turned off. When the appliance is turned on, press “

” button, the appliance

powers off; the ember bed, ﬂame, heating element and background light are turned

off. The other function buttons listed as following can only work under the condition

that the “

” is on. If the ﬂame is off when the appliance is turned off, the brightness

level of the ﬂame and ember bed LED are set to highest when “

” is pressed to turn

on the appliance.

3. Button "

": When the ﬂame and ember bed LEDs are turned on, press the button,

and the light of the ﬂame and ember bed will turn off. When the ﬂame and ember bed

LEDs are off, press the button to turn on the ﬂame and ember bed LEDs.

4. Yellow button “

” controls the six brightness levels of the yellow LED ﬂame lights;

the brightness level changes with each press until you turn the light off completely;

press the button again to repeat the cycle.

5. Blue button “

”, controls the six brightness levels of the blue LED ﬂame lights; the brightness level changes

with each press until you turn the light off completely; press the button again to repeat the cycle.

6. Pink button “

”, controls the six brightness levels of the pink LED ﬂame lights; the brightness level changes

with each press until you turn the light off completely; press the button again to repeat the cycle.

7. Ember button “

”, controls the six brightness levels of ember bed LED lights; the brightness level changes

with each press until you turn the light off completely; press the button again to repeat the cycle.

8. Button “ ”, press this button to turn on the heating element. The heating element starts to work on

“HIGH” mode with the power at 1500W; press the button again to turn off the heating element.

9. Button “

”, press this button and the heating element starts to work on “LOW” mode (750W), press again

and the heating element starts to work on “HIGH” mode (1500W). Press again to repeat the cycle change.

10. Button “

”, press this to start TEMP mode. When "TEMP mode is on, the appliance automatically sets the

room temperature at 25°C. When the room temperature is above 25°C, the heating element shuts off. When

the room temperature is below 22°C, the heating element starts working at 1500W. When the room tempera-

ture is between 22-25°C, the heating element starts working at 750W.

Caution: “HIGH” “LOW” “TEMP” buttons only work under the condition when “

” is in the on position.

When the appliance is on “HIGH” or “LOW” mode, the heating element is turned on all the time and the

thermostat will not work.

11. Button “

” controls the ceiling light. Below shows the work mode of the ceiling light:

Blue Amber Yellow Blinking Switch off

W415-2166 / B / 10.17.18

18

EN

6.2 CRYSTAL EMBER PLACEMENT

1. Unscrew the two screws at the bottom of the front plate.

2. Unhook and lift off the frame of the inner surface and

place carefully on a safe work surface.

3. Unscrew the two screws on the ember tray with a screw-

driver.

4. Remove the logset and put the crystals in.

5. Re-install the frame of the inner surface.

FRONT PLATE

UNSCREW LOGSET

Front View of Appliance

PLACE CRYSTALS

2 Screws

UNHOOK INNER FRAME

PLACE CRYSTALS

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

W415-2166 / B / 10.17.18

19

EN

6.3 LED / REMOTE RECEIVER / THERMOSTAT REPLACEMENT

6.4 FUSE REPLACEMENT

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

1. To replace LED lights in the ember bed, ﬂame and/or decorative lights, disconnect the quick connect plug

from the control board and replace with a new one.

2. To replace the remote receiver and thermostat wires, disconnect the quick connect plug from the control

board and replace with a new one.

T

O

P

L

IG

H

T

F

L

A

M

E

L

E

D

E

M

B

E

R

B

E

D

/ L

O

G

L

E

D

T

H

E

R

M

O

S

T

A

T

R

E

M

O

T

E

R

E

C

E

IV

E

R

C

O

N

T

R

O

L

P

A

N

E

L

F

U

S

E

C

O

V

E

R

1. Remove the plastic cover from the fuse. Pull the fuse (2Amp) out from the control board. Install the re-

placement fuse and plastic cover.

W415-2166 / B / 10.17.18

20

EN

7.0 REPLACEMENT PARTS

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts

can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE

REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:



Model & Serial Number of appliance



Installation date of appliance



Part number



Description of part



Finish

PARTS, PART NUMBERS AND AVAILABILITY ARE SUBJECT TO CHANGE WITHOUT NOTICE.

PARTS IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN 2 TO 5 BUSINESS DAYS FOR MOST

DELIVERY DESTINATIONS.

PARTS NOT IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN A 2 TO 4 WEEK PERIOD, FOR

MOST CASES.

PARTS IDENTIFIED AS ‘SO’ ARE SPECIAL ORDER AND CAN TAKE UP TO 90 DAYS FOR DELIVERY.

FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE

ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

** THIS IS A FAST ACTING THERMOCOUPLE. IT IS AN INTEGRAL SAFETY COMPONENT. REPLACE ONLY WITH

A FAST ACTING THERMOCOUPLE SUPPLIED BY WOLF STEEL LTD.

!

WARNING

COMPONENTS

REF # PART # DESCRIPTION STOCKED

1

W300-0178 (540G) CRYSTAL YES

2

W300-0246 LARGE DECORATIVE CRYSTAL YES

3

W190-0109 CIRCUIT BOARD YES

4

W010-3966 HEATER AND BLOWER ASSEMBLY YES

5

W660-0128 MAIN POWER SWITCH YES

6

W190-0110 REMOTE CONTROL YES

7

W405-0043 EMBER BED LED YES

8

GBL38-001.02-00 FRONT GLASS PANEL YES

9

GBL38-000-07 MIRROR GLASS YES

10

W010-3965 DRUM ASSEMBLY YES

11

W660-0129 REMOTE RECEIVER YES

12

W080-1719 MEDIA TRAY SO

13

W435-0080 DRUM MOTOR YES

14

W285-0006 FUSE YES

15

W135-0646 LOG SET YES

16

W680-0022 THERMO-CONTROLLED SENSOR YES

ACCESSORIES

REF # PART # DESCRIPTION

17*

W660-0081 DIGITAL THERMOSTAT

18*

W690-0001 MILLIVOLT THERMOSTAT

For after sales service, please call 1-866-820-8686

La page est en cours de chargement...

NAPOLEON NEFB30GL Mode d'emploi

NAPOLEON NEFB30GL Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents