DeWalt D55167 Manuel utilisateur

D55167

Oil-Free Portable Air Compressor

Compresseur d’air portatif sans huile

Compresor de aire sin aceite portátil

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-De

2



A. Auto(I)/Off(O) Switch

B. Air Tank Pressure Gauge

C. Regulated Pressure Gauge

D. Regulator

E. Quick Connect



Voltage: Single Phase 120V

Minimum branch circuit requirement: 15 A

Fuse Type: Time delay



MODEL

D55167

WEIGHT

85 lbs. (38.6 kg)

HEIGHT

27.5" (698.5 mm)

WIDTH

18.0" (457.2 mm)

LENGTH

21.25" (539.8 mm)

AIR TANK CAPACITY

15 gallons (56.8 liters)

APPROX CUT-IN PRESSURE

160 psi

APPROX. CUT-OUT PRESSURE

200 psi

SCFM @ 90 PSI

4.8 *

NOISE LEVEL

79 dBA

+

*Tested per ISO 1217:1996

+Tested per ISO 3744:1994



F. Check Valve

G. Safety Valve

H. Air Tank Drain Valve

(not shown)

I. Pressure Switch

J. Air Intake Filter





Noise Emission Values

Sound Pressure Level: LpA = 79.0 dBA re 20μPA

Uncertainty in the Sound Pressure Level: KpA = 3.0 dBA re 20μPA

Sound Power Level: LwA = 93.0 dBA re 1 pw

Uncertainty in the Sound Power Level: KwA = 3.0 dBA re 1 pw

The sum of the emission value and the uncertainty is the limit

below which there is a 95% confidence the value of a single tool

will lie below when the tool is new.

FIG. 1

A

E

C

B

D

I

F

J

G

3





The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

these symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

e

WALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

e

WALT (1-800-433-9258)



WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

WARNING: This product contains chemicals known to the State

of California to cause cancer, and birth defects or other reproductive

harm. Wash hands after handling.

WARNING: Some dust contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm

such as asbestos and lead in lead based paint.



DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Itisnormalforelectricalcon-

tacts within the motor and

pressure switch to spark.

 • Alwaysoperatethecompres-

sor in a well ventilated area

free of combustible materials,

gasoline, or solvent vapors.

 • Ifelectricalsparksfrom

compressor come into con-

tact with flammable vapors,

they may ignite, causing fire

or explosion.

 • Ifsprayingflammablemateri-

als, locate compressor at

least 20 feet (6.1 m) away

from spray area. An addi-

tional length of hose may be

required.

 • Storeflammablematerialsin

a secure location away from

compressor.

4



 • Restrictinganyofthe

compressor ventilation

openings will cause serious

overheating and could

cause fire.

 • Neverplaceobjectsagainstor

on top of compressor.

 • Operatecompressorin

an open area at least 12"

(30.5 cm) away from any

wall or obstruction that would

restrict the flow of fresh air to

the ventilation openings.

 • Operatecompressorina

clean, dry well ventilated area.

Do not operate unit indoors or

in any confined area.

 • Unattendedoperationof

this product could result in

personalinjuryorproperty

damage. To reduce the risk

of fire, do not allow the

compressor to operate unat-

tended.

 • Alwaysremaininattendance

with the product when it is

operating.

 • Alwaysturnoffandunplug

unit when not in use.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Thecompressedairdirectly

from your compressor is not

safe for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminants can cause

seriousinjuryordeath.

• Neveruseairobtaineddirectly

from the compressor to supply

air for human consumption.

The compressor is not

equipped with suitable filters

and in-line safety equipment

for human consumption.

• Exposuretochemicals

in dust created by

power sanding, sawing,

grinding, drilling, and other

construction activities may

be harmful.

• Sprayedmaterialssuchas

paint, paint solvents, paint

remover, insecticides, weed

killers, may contain harmful

vapors and poisons.

• Workinanareawithgood

cross ventilation. Read and

follow the safety instructions

provided on the label or

safety data sheets for the

materials you are spraying.

Always use certified safety

equipment: NIOSH/OSHA

respiratory protection or

properly fit ting face mask

designed for use with your

specific application.

5



WARNING: RISK OF BURSTING

Air Tank: On February 26, 2002, the U.S. Consumer Product

Safety Commission published Release # 02-108 concerning air

compressor tank safety:

Air compressor receiver tanks do not have an infinite life. Tank life

is dependent upon several factors, some of which include operat-

ing conditions, ambient conditions, proper installations, field modi-

fications, and the level of maintenance. The exact effect of these

factors on air receiver life is difficult to predict.

If proper maintenance procedures are not followed, internal corro-

sion to the inner wall of the air receiver tank can cause the air tank

to unexpectedly rupture allowing pressurized air to suddenly and

forcefullyescape,posingriskofinjurytoconsumers.

Your compressor air tank must be removed from service by the end

of the year shown on your tank warning label.

The following conditions could lead to a weakening of the air tank,

and result in a violent air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failuretoproperlydrain

condensed water from

air tank, causing rust and

thinning of the steel air tank.

• Drainairtankdailyorafter

each use. If air tank develops

a leak, replace it immediately

with a new air tank or replace

the entire compressor.

• Modificationsorattempted

repairs to the air tank.

• Neverdrillinto,weld,ormake

any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

• Unauthorizedmodificationsto

the safety valve or any other

components which control air

tank pressure.

• Theairtankisdesigned

to withstand specific

operating pressures. Never

makeadjustmentsorparts

substitutions to alter the factory

set operating pressures.

Attachments & accessories:

• Exceedingthepressure

rating of air tools, spray guns,

air operated accessories,

tires, and other inflatables

can cause them to explode or

fly apart, and could result in

seriousinjury.

• Followtheequipment

manufacturers

recommendation and never

exceed the maximum allowable

pressure rating of attachments.

Never use compressor to

inflate small low pressure

objectssuchaschildren’stoys,

footballs, basketballs, etc.

6



TIres:

• Over inflation of tires could

resultinseriousinjuryand

property damage.

 • Useatirepressuregaugeto

check the tires pressure before

each use and while inflating

tires; see the tire sidewall for

the correct tire pressure.

NOTE:

Air tanks, compressors

and similar equipment used to

inflate tires can fill small tires

veryrapidly.Adjustpressure

regulator on air supply to no

more than the rating of the tire

pressure. Add air in small incre-

ments and frequently use the tire

gauge to prevent over inflation.

WARNING: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your air compressor is

powered by electricity.

Like any other electrically

powered device, If it is not

used properly it may cause

electric shock.

 • Never operate the compressor

outdoors when it is raining or

in wet conditions.

 • Never operate compressor

with protective covers

removed or damaged.

 • Repairs attempted by

unqualified personnel can

resultinseriousinjuryor

death by electrocution.

 • Any electrical wiring or

repairs required on this

product should be performed

by a D

eWALT factory

service center or a D

eWALT

authorized service center in

accordance with national and

local electrical codes.

 • Electrical Grounding:

Failure to provide adequate

grounding to this product

couldresultinseriousinjury

or death from electrocution.

See Grounding

Instructions under

Installation.

 • Make certain that the

electrical circuit to which the

compressor is connected

provides proper electrical

grounding, correct voltage and

adequate fuse protection.

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Thecompressedairstream

can cause soft tissue

damage to exposed skin and

can propel dirt, chips, loose

particles,andsmallobjects

at high speed, resulting in

property damage or personal

injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Neverpointanynozzleor

sprayer toward any part of

the body or at other people or

animals.

7



• Alwaysturnthecompressoroff

and bleed pressure from the

air hose and air tank before

attempting maintenance,

attaching tools or accessories.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touchingexposedmetalsuch

as the compressor head,

engine head, engine exhaust

or outlet tubes, can result in

serious burns.

 • Nevertouchanyexposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation.

 • Donotreacharound

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Movingpartssuchasthe

pulley, flywheel, and belt can

causeseriousinjuryifthey

come into contact with you or

your clothing.

• Neveroperatethecompressor

with guards or covers which

are damaged or removed.

• Keepyourhair,clothing,and

gloves away from moving parts.

Looseclothes,jewelry,orlong

hair can be caught in moving

parts.

• Airventsmaycovermoving

parts and should be avoided as

well.

• Attemptingtooperate

compressor with damaged or

missing parts or attempting

to repair compressor with

protective shrouds removed

can expose you to moving

parts and can result in

seriousinjury.

• Anyrepairsrequiredonthis

product should be performed

by a D

eWALT factory service

center or a D

eWALT authorized

service center.

8



WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafeoperationofyourair

compressor could lead to

seriousinjuryordeathtoyou

or others.

• Reviewandunderstandall

instructions and warnings in

this manual.

• Becomefamiliarwiththe

op eration and con trols of the

air compressor.

• Keepoperatingareaclearofall

persons, pets, and obstacles.

• Keepchildrenawayfromtheair

compressor at all times.

• Donotoperatetheproduct

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Neverdefeatthesafetyfea

tures of this prod uct.

• Equipareaofoperationwitha

fire extinguisher.

• Donotoperatemachinewith

missing, broken, or un au tho-

rized parts.

WARNING: RISK OF FALLING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Aportablecompressor

can fall from a table,

workbench, or roof causing

damage to the compressor

and could result in serious

injuryordeathtothe

operator.

• Alwaysoperatecompressorina

stable secure position to prevent

accidental movement of the unit.

Never operate compressor on a

roof or other elevated position.

Use additional air hose to reach

high locations.

WARNING: RISK OF INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Seriousinjurycanresult

from attempting to lift too

heavyanobject.

•The compressor is too heavy

to be lifted by one person.

Obtain assistance from

others before lifting.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Under some conditionsand

duration of use, noise from

this product may contribute

to hearing loss.

 • Alwayswearcertifiedsafety

equipment: ANSI S12.6

(S3.19) hearing protection.

9









AUTO/OFF SWITCH

Place this switch (A) in the AUTO (I)

F

A

I

position to provide automatic power

to the pressure switch and OFF (O)

to remove power at the end of each

use.

PRESSURE SWITCH

The pressure switch (I) automatically starts the motor when the

air tank pressure drops below the factory set cut-in pressure. It

stops the motor when the air tank pressure reaches the factory set

cut-out pressure.

SAFETY VALVE

If the pressure switch does not

C

D

B

G

E

shut off the air compressor at its

cut-out pressure setting, the safety

valve (G) will protect against high

pressure by popping out at its

factory set pressure (slightly higher

than the pressure switch cut-out

setting).

CHECK VALVE

When the air compressor is operating, the check valve (F) is

open, allowing compressed air to enter the air tank. When the

air compressor reaches cut-out pressure, the check valve closes,

allowing air pressure to remain inside the air tank.

TANK PRESSURE GAUGE

The tank pressure gauge (B) indicates the reserve air pressure in

the tank.

REGULATED PRESSURE GAUGE

The outlet pressure gauge (C) indicates the air pressure available

at the outlet side of the regulator. This pressure is controlled by the

regulator and is always less than or equal to the tank pressure.

REGULATOR

The regulator (D) controls the air pressure shown on the regulated

pressure gauge. Pull the knob out and turn clockwise to increase

pressure and counterclockwise to decrease pressure. When the

desired pressure is reached push knob in to lock in place.

UNIVERSAL QUICK CONNECT BODY

The universal quick connect body (E) accepts the three most

popular styles of quick connect plugs: Industrial, automotive, and

ARO. One hand push-to-connect operation makes connections

simple and easy.

DRAIN VALVE

The drain valve (H) is located at the base of the air

DRAIN TANK DA ILY

H

tank and is used to drain condensation at the end

of each use.

See Draining Air Tank under

Maintenance.

COOLING SYSTEM

This compressor contains an advanced design cooling system.

It is normal for this fan to blow air through the vent holes in large

amounts. The cooling system is working when air is expelled.

AIR COMPRESSOR PUMP

The pump compresses air into the air tank. Working air is not

available until the compressor has raised the air tank pressure

above that required at the air outlet.

10



AIR INTAKE FILTER

The filter (J) is designed to clean air entering the pump. To ensure

the pump continually receives a clean, cool, and dry air supply the

filter must always be clean and the filter intake must be free from

obstructions.

MOTOR OVERLOAD PROTECTOR

The motor has a thermal overload protector. If the motor overheats

for any reason, the overload protector will shut off the motor. The

motor must be allowed to cool down before restarting. To restart:

1. Set the Auto/Off lever to OFF and unplug unit.

2. Allow the motor to cool.

3.

Plug the power cord into the correct branch circuit receptacle.

4. Set the Auto/Off lever to AUTO position.





INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 psi.

2. Grasp the hose at the quick connect plug and push the plug

into the quick connect body (E). Coupler will snap into place.

3. Grasp the hose and pull to ensure coupler is seated.

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 psi.

2. Pull coupler on quick connect body back to release Quick

Connect plug on hose.



WARNING: Risk of Electrical Shock. In the event of a short

circuit, grounding reduces the risk of shock by providing an escape

wire for the electric current. This air compressor must be properly

grounded.

The portable air compressor is equipped with a cord having a

grounding wire with an appropriate grounding plug.

1. The cord set and plug (M) with this unit

L

M

K

contains a grounding pin (L). This plug

MUST be used with a grounded

outlet (K).

IMPORTANT: The outlet being used must

be installed and grounded in accordance

with all local codes and ordinances.

2. Ensure the outlet being used has the same configuration as the

grounded plug. DO NOT USE AN ADAPTER.

3. Inspect the plug and cord before each use. Do not use if there

are signs of damage.

4. If these grounding instructions are not completely understood, or

if in doubt as to whether the compressor is properly grounded,

have the installation checked by a qualified electrician.

DANGER: Risk of Electrical Shock. IMPROPER GROUNDING

CAN RESULT IN ELECTRICAL SHOCK.

• Donotmodifytheplugprovided.Ifitdoesnotfittheavailable

outlet, a correct outlet should be installed by a qualified

electrician.

• RepairstothecordsetorplugMUSTbemadebyaqualified

electrician.

11





If an extension cord must be used, be sure it is:

 • a3wireextensioncordthathasa3bladegroundingplug,and

a 3-slot receptacle that will accept the plug on the product

 •ingoodcondition

 •nolongerthan50feet(15.2m)

 • 12 gauge (AWG) or larger.  (Wire size increases as gauge

number decreases. 10 AWG and 8 AWG may also be used. DO

NOT USE 14 OR 16 AWG.)

NOTICE: The use of an undersized extension cord will cause

voltage to drop resulting in power loss to the motor and overheating.

Instead of using an extension cord, increase the working reach of

the air hose by attaching another length of hose to its end. Attach

additional lengths of hose as needed. Always use a minimum 3/8"

(9.5 mm) or greater air hose rated at 300 psi.



Refer to the Voltage and Minimum Branch Circuit Requirements

under Pump/Motor Specifications.

CAUTION: Certain air compressors can be operated on a

15 amp circuit if the following conditions are met.

• Voltage supply to circuit must comply with the National

Electrical Code.

• Circuitisnotusedtosupplyanyotherelectricalneeds.

• Extensioncordscomplywithspecifications.

• Circuitisequippedwitha15ampcircuitbreakeror15amp

time delay fuse. NOTE: If compressor is connected to a circuit

protected by fuses, use only time delay fuses. Time delay

fuses should be marked “D” in Canada and “T” in the US.

If any of the above conditions cannot be met, or if operation of the

compressor repeatedly causes interruption of the power, it may be

necessary to operate it from a 20 amp circuit. It is not necessary

to change the cord set.



NOTE: Always use an air line filter to remove moisture and oil vapor

when spraying paint.



Place the air compressor in a clean, dry and well ventilated area

at least 12" (30.5 cm) away from the wall or other obstructions that

will interfere with the flow of air. Keep the compressor away from

areas that have dirt and/or volatile fumes in the atmosphere. These

impurities may clog the intake filter and valves, causing inefficient

operation.

WARNING: The air compressor pump and shroud are designed to

allow for proper cooling. The ventilation openings on the compressor

are necessary to maintain proper operating temperature. Do not

place rags or other containers on or near these openings.

Place the air compressor on a flat surface resting on the rubber

feet and wheels.

ELECTRICAL

Refer to all safety instructions before using unit. Observe extension

cord safety instructions if necessary. Always move the Auto/Off

switch (A) to the OFF position before removing the plug from the

outlet.

TRANSPORTING

When transporting the compressor in a vehicle, trailer, etc., make

sure the tank is drained and the unit is secured with straps to prevent

tipping. Use care when driving to prevent tipping the unit over in the

vehicle. Damage can occur to the compressor or surrounding items

if the compressor is tipped.

12



LIFTING

Always use two people when lifting and lift from

N

the recommended lift points (N). DO NOT lift

by wheels or shroud.

MOVING

CAUTION: The wheels and handle do

not provide adequate clearance, stability, or

support for pulling the unit up and down stairs or steps. The unit

must be lifted or pushed up a ramp.

1. Grasp handle of compressor and tilt compressor back to rest on

wheels.

WARNING: Risk of Unsafe Operation. Ensure proper footing and

use caution when rolling compressor so that unit does not tip or

cause loss of balance.

2. When location is reached slowly lower compressor to ground.

Always store compressor in a horizontal position resting

on the rubber bumpers and wheels.



WARNING: Do not operate this unit until you read this instruction

manual for safety, operation and maintenance instructions.



1.

Ensure the Auto/Off switch (A) is in the OFF position.

2.

Plug the power cord into the correct branch circuit receptacle.

See Voltage and Circuit Protection under Installation.

3. Ensure air tank is drained, see Draining Air Tank under

Maintenance.

4. Ensure the drain valve (H) is closed.

5. Ensure safety valve (G) is functioning properly, see Checking

Safety Valve under Maintenance.

6. Pull the regulator knob (D) out and turn counterclockwise until fully

closed. Ensure regulated pressure gauge reads 0 psi. Push knob

in to lock in place.

7. Attach hose and accessories. NOTE: Always use a minimum

3/8" (9.5 mm) or greater air hose rated at 300 psi.

WARNING: Risk of unsafe operation. Firmly grasp air hose in hand

when installing or disconnecting to prevent hose whip.

WARNING:

Risk of unsafe operation. Do not use damaged or

worn accessories.

WARNING: Risk of Bursting. Too much air pressure causes a

hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator outlet

pressure must never exceed the maximum pressure rating.





1. Follow Pre-Start Checklist under Preparation for Use.

2. Move the Auto/Off switch to the AUTO position and allow tank

pressure to build. Motor will stop when tank pressure reaches

cut-out pressure.

NOTICE: Risk of property damage. Compressed air from the unit

may contain wa ter condensation and oil mist. Do not spray un fil-

tered air at an item that could be damaged by moisture. Some air

op er ated tools or de vic es may require filtered air. Read the in struc-

tions for the air tool or device.

 3.Adjust regulator (D) to desired setting. See Regulator under

Features.



1. Move Auto/Off switch (A) to the OFF position. NOTE: If finished

using compressor, follow Steps 2 - 6.

13



2. Pull the regulator knob (D) out and turn counterclockwise until fully

closed. Ensure regulated pressure gauge reads 0 psi. Push knob

in to lock in place.

3. Remove hose and accessory.

WARNING: Risk of unsafe operation. Firmly grasp air hose in hand

when installing or disconnecting to prevent hose whip.

4. Drain the air tank,

see Draining Air Tank under Maintenance

.

Ensure air tank pressure gauge reads 0 psi.

WARNING: Risk of bursting. Drain air tank daily. Water will

condense in air tank. If not drained, water will corrode and weaken

the air tank causing a risk of air tank rupture.

5. Allow the compressor to cool down.

6. Wipe air compressor clean and store in a safe, non-freezing area.



The following procedures must be followed when maintenance or

service is performed on the air compressor.

1. Ensure Auto/Off switch is in the OFF position.

2. Remove air compressor plug from outlet.

3. Drain air tank.

4. Allow air compressor to cool down before starting service.

NOTE: All compressed air systems contain maintenance parts (e.g.,

oil, filters, separators) that are periodically replaced. These used parts

may contain substances that are regulated and must be disposed of in

accordance with local, state, and federal laws and regulations.

NOTE: Take note of the positions and locations of parts during

disassembly to make reassembly easier.

NOTE: Any service operations not included in this section should

be performed by a D

e

WALT factory service center or a D

e

WALT

authorized service center.



Procedure Daily Weekly

See tank

warning

label

Check safety valve

X

Inspect air filter

X

Drain air tank

X

Check for unusual noise/vibration

X

Check for air leaks

X

1

Clean compressor exterior

X

Remove tank from service

X

2

1Tocheckforairleaksapplyasolutionofsoapywateraroundjoints.

While compressor is pumping to pressure and after pressure cuts out,

look for air bubbles to form.

2 - For more information, call 1-800-4-D

e

WALT (1-800-433-9258)



WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or

an explosion.

WARNING: Risk from flying objects. Always wear certified safety

equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3) with side

shields when using the compressor.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. NOTE: Ring may

be difficult to pull when air tank pressure is at 0 psi. If the valve is

stuck or does not operate smoothly, it must be replaced with the

same type of valve.

14





WARNING: Risk of unsafe operation. Risk from noise. Air tanks

contain high pressure air. Keep face and other body parts away from

outlet of drain. Use eye protection [ANSI Z87.1 (CAN/CSA Z94.3)]

when draining as debris can be kicked up into face.

WARNING: Risk from noise. Use ear protection [ANSI S12.6

(S3.19)] as air flow noise is loud when draining.

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g. tanks, filter, aftercoolers, dryers).

This condensate contains lubricating oil and/or substances which

may be regulated and must be disposed of in accordance with local,

state, and federal laws and regulations.

1. Ensure Auto/Off switch is in the OFF position.

2. Place a suitable container under the drain valve (H) to catch

discharge.

3. Grasp lever on drain valve.

4. Slowly rotate lever to gradually bleed air from air tank.

WARNING: Risk of bursting. Drain air tank daily. Water will

condense in air tank. If not drained, water will corrode and weaken

the air tank causing a risk of air tank rupture.

NOTICE: Risk of property damage. Drain water from air tank may

contain oil and rust, which can cause stains.

5. When air tank pressure gauge reads 10 psi, rotate valve to the

fully open position.

6. Close drain valve when finished.



WARNING: Hot surfaces. Risk of burn. Outlet tube, pump head,

and surrounding parts are very hot, do not touch. Allow compressor

to cool prior to servicing.

1. Ensure Auto/Off switch (A) is in the OFF Position.

2. Allow unit to cool.

3. Remove filter cover (J) from base.

4. Remove element from filter base.

J

5. Place new element back in filter

base. Purchase replacement parts

from your local dealer or authorized

service center. Always use identical

replacement parts.

6. Snap filter cover to filter base.

NOTICE: Risk of unsafe operation. Do not operate without air inlet

filter



Recommended accessories for use with your tool are available

for purchase from your local dealer or authorized service center.

If you need assistance in locating any accessory for your tool,

please contact D

e

WALT Industrial Tool Co., 701 East Joppa Road,

Baltimore, MD 21286, call 1-800-4-D

e

WALT (1-800-433-9258) or visit

our website www.dewalt.com.

WARNING: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the air compressor.



Please have the following information available for all service calls:

Model Number ____________ Serial Number _________________

Date and Place of Purchase ______________________________



To assure product SAFETY and RELIABILITY, repairs, maintenance

andadjustmentshouldbeperformedbyaD

e

WALT factory service

center, a D

e

WALT authorized service center or other qualified

service personnel. Always use identical replacement parts.

15





DeWALT heavy duty industrial tools are warranted for one year from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-D

e

WALT (1-800-433-9258). This warranty does not

apply to accessories or damage caused where repairs have been

made or attempted by others. This warranty gives you specific legal

rights and you may have other rights which vary in certain states or

provinces.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-D

e

WALT

(1-800-433-9258) for a free replacement.

WARNING

DRAIN TANK D AILY

OR AFTER EVERY 4 HOURS OF USE. CONDENSATION BUILD-UP MAY CAUSE

CORROSION INSIDE TANK RESULTING IN TANK FAILURE. SEE MANUAL FOR INSPECTION PROCEDURES.

TO DRAIN TANK OPEN V A LVE SLOWLY AND TILT COMPRESSOR TO EMPTY ACCUMULATED W A TER.

ADVERTENCIA

DRENE EL TANQUE A DIARIO O DESPUÉS DE CAD A 4 HORAS DE USO. LA ACUMULACIÓN DE

CONDENSACIÓN PUEDE OCASIONAR CORROSIÓN DENTRO DEL TANQUE Y PROVOCAR FA LLA DEL

TANQUE. CONSULTE EL MANUAL P A RA CONOCER LOS PROCEDIMIENTOS DE INSPECCIÓN. P A RA DRENAR EL TANQUE, ABRA LA

VÁ LVULA LENT A MENTE E INCLINE EL COMPRESOR P A RAELIMINAR EL AGUA ACUMULAD A.

AVERTISSEMENT

RÉSERVOIR DE VIDANGE QUOTIDIEN OU APRÈS TOUTES LES 4 HEURES D'UTILISATION.

L'HABILLAGE DE CONDENSATION PEUT CAUSER LA CO RROSION À L'INTÉRIEUR DU RÉSERVOIR A Y ANT

POUR RÉSUL T A T L'ÉCHEC DE RÉSERVOIR. VOIR LE MANUEL POUR DES PROCÉDURES D'INSPECTION. À LA V A L V E

OUVERTE DE RÉSERVOIR DE VIDANGE LENTEMENT ET A U CO MPRESSEUR D'INCLINAISON À L ' EAU ACCUMULÉE VIDE.

WARNING

HOT SURF A CES

ADVERTENCIA

SUPERFICIES CALIENTES

AVERTISSEMENT SURFACES CHAUDES

DO NOT ADJUST F A CTORY SETTINGS.

TO REDUCE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER.

Pressure c ontrols set at factory for

maximum safe operation.

NO H AGA CAM BIO S E N LOS AJ UST ES

DE FÁ BRIC A. NO RET IRE LA T A P A P A RA

REDU CIR EL RIE SGO DE CHO QUE EL ÉCT RICO .

Los c ontr ole s d e pr esi ón s e a jus tan en la

fábr ica pa ra m áxi ma segu rid ad en l a o pera ció n.

ADVERTENCIA

WARNING

AVERTISSEMENT



CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air

delivery.

PSI: Pounds per square inch; a unit of measure of pressure.

Code Certification: Products that bear one or more of the

following marks: UL

®

*, CUL, ETL

®

*, CETL, have been evaluated

by OSHA certified independent safety laboratories and meet the

applicable Standards for Safety.

* UL

®

is a registered trademark of Underwriters Laboratories

and ETL

®

is a registered trademark of Electrical Testing

Laboratories.

Cut-In Pressure: While the motor is off, air tank pressure drops

when accessory is used. When the tank pressure drops to a certain

low level the motor will restart automatically. The low pressure at

which the motor automatically restarts is called cut-in pressure.

Cut-Out Pressure: When an air compressor is turned on and

begins to run, air pressure in the air tank begins to build. It builds

to a certain high pressure before the motor automatically shuts

off, protecting your air tank from pressure higher than its capacity.

The high pressure at which the motor shuts off is called cut-out

pressure.

Branch Circuit: The circuit carrying electricity from electrical

panel to outlet.

Duty Cycle: This air compressor pump is capable of running

continuously. However, to prolong the life of your air compressor,

it is recommended that a 50%-75% average duty cycle be

maintained; that is, the air compressor pump should not run more

than 30-45 minutes in any given hour.

16





This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance

personnel can perform some corrective actions, and others may require the assistance of a qualified D

eWALT technician or your dealer.

Problem Code

Excessive air tank pressure-safety valve pops off ......................................................................1, 2

Air leaks ....................................................................................................................................3

Air leaks in air tank or at air tank welds ....................................................................................4

Air leaks between head and valve plate ....................................................................................5

Air leaks from safety valve .........................................................................................................6

Knocking Noise ..........................................................................................................................6

Pressure reading on the regulated pressure gauge drops when an accessory is used ...........7

Compressor is not supplying enough air to operate accessories..............................................8, 9, 10, 11, 12, 22

Regulator knob has continuous air leak ....................................................................................13

Regulator will not shut off air outlet ...........................................................................................13

Motor will not run .......................................................................................................................6, 14, 15, 16, 17, 18, 19, 20

Squealing Sound .......................................................................................................................21



CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 Pressure switch does not shut off motor when

compressor reaches cut-out pressure

Set the Auto/Off switch to OFF, if the unit does not shut off contact

a D

e

WALT factory service center or a D

e

WALT authorized service

center.

2 Pressure switch cut-out too high Contact a D

e

WALT factory service center or a D

e

WALT authorized

service center.

3 Tube fittings are not tight enough Tighten fittings where air can be heard escaping. Check fittings

with soapy water solution. Do Not Overtighten.

17



CODE POSSIBLE CAUSE POSSIBLE SOLUTION

4 Defective air tank Air tank must be replaced. Do not repair the leak.

WARNING: Risk of bursting. Do not drill into, weld or other-

wise modify air tank or it will weaken. The air tank can rupture or

explode.

5 Leaking seals Contact a D

e

WALT factory service center or a D

e

WALT authorized

service center.

6 Defective safety valve Operate safety valve manually by pulling on ring. If valve still leaks,

it must be replaced.

7

Regulatorisnotadjustedcorrectlyforaccessory

being used

It is normal for some pressure drop to occur when an accessory

isused,adjusttheregulatorasinstructedinRegulator under

Features if pressure drop is excessive.

NOTE:Adjusttheregulatedpressureunderflowconditionswhile

accessory is being used.

8 Prolonged excessive use of air Decrease amount of air usage.

9 Compressor is not large enough for accessory Check the accessory air requirement. If it is higher than the CFM

or pressure supplied by your air compressor, a larger compressor

is needed to operate accessory.

10 Hole in air hose Replace air hose.

11 Check valve restricted Remove, clean or replace.

12 Air leaks Tighten fittings.

13 Regulator is damaged Replace.

14 Motor overload protection switch has tripped Refer to Motor Overload Protection under Features. If motor over-

load protection trips frequently, contact a D

e

WALT factory service

center or a D

e

WALT authorized service center.

18



CODE POSSIBLE CAUSE POSSIBLE SOLUTION

15 Tank pressure exceeds pressure switch cut-in

pressure

Motor will start automatically when tank pressure drops below cut-

in pressure of pressure switch.

16 Extension cord is wrong length or gauge Check for proper gauge wire and cord length refer to the Extension

Cords under Installation.

17 Loose electrical connections Check wiring connection inside pressure switch and terminal box

area.

18 Possible defective motor Contact a D

e

WALT factory service center or a D

e

WALT authorized

service center.

19 Paint spray on internal motor parts Contact a D

e

WALT factory service center or a D

e

WALT authorized

service center. Do not operate the compressor in the paint spray

area. See Risk of Explosion or Fire warning under Important

Safety Instructions.

20 Fuse blown, circuit breaker tripped 1. Check fuse box for blown fuse and replace as necessary. Reset

circuit breaker. Do not use a fuse or circuit breaker with higher

rating than that specified for our particular branch circuit.

2. Check for proper fuse. You should use a time delay fuse.

3. Check for low voltage conditions and/or proper extension cord.

4. Disconnect the other electrical appliances from circuit or operate

the compressor on its own branch circuit.

21 Worn Belt Contact a D

e

WALT factory service center or a D

e

WALT authorized

service center.

22 Restricted air intake filter Clean or replace air intake filter. Do not operate the air compressor

with the filter removed. Refer to the Air Filter paragraph in the

Maintenance section.

19





A. Interrupteur Auto(I)/Arrêt (O)

 B.Manomètreduréservoird’air

C. Manomètre régulé

D. Régulateur

E. Branchements rapides

F. Clapet

G. Soupape de sûreté

H. Soupape de purge du

réservoird’air(nonmontré)

I. Rembobineur de cordon

d’alimentation

J. Filtred’admissiond’air



Tension : monophasé, 120V

Exigence minimale du circuit de dérivation : 15 A

Type de fusible : temporisation



MODÈLE

D55167

POIDS

38,6 kg (85 livres)

HAUTEUR

698,5 mm (27,5 po)

LARGEUR

457,2 mm (18,0 po)

LONGUEUR

539,8 mm (21,25 po)

CAPACITÉ DU RÉSERVOIR D’AIR

56,8 liters (15 gallons)

PRESSION D’ENCLENCHEMENT

APPROX.

160 psi

ENV. PRESSION DE DÉCLENCHEMENT

200 psi

PCMS (SCFM) @ 90 PSI

4,8 *

NIVEAU SONORE

79 dBA

+

*Testé conformément à la norme ISO 1217

+ Testé conformément à la norme ISO 3744





Valeur de l’émission de bruits

Niveau de pression acoustique : LpA = 79,0 dBA re 20μPA

Incertitude du niveau de

pression acoustique calculé : KpA = 3,0 dBA re 20μPA

Niveau de puissance acoustique : LwA = 93,0 dBA re 1 pw

Incertitude du niveau de puissance

acoustique : KwA = 3,0 dBA re 1 pw

Lasommedelavaleurdel’émissionetdel’incertitudeétablitla

limite sous laquelle la valeur pour un seul outil y sera inférieure et

ce, à 95 % de fiabilité statistique.

FIG. 1

A

E

C

B

D

I

F

J

20







Les définitions ci-dessous décrivent le niveau de gravité pour

chaque symbole. Veuillez lire le mode d’emploi et porter une

attention particulière à ces symboles.

DANGER : Indique une situation dangereuse imminente qui, si

elle n’est pas évitée, causera la mort ou des blessures graves.

AVERTISSEMENT :

Indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait se solder par un

décès ou des blessures graves.

ATTENTION : Indique une situation potentiellement dangereuse

qui, si elle n’est pas évitée pourrait se solder par des blessures

mineures ou modérées.

AVIS : Indique une pratique ne posant aucun risque de

dommages corporels mais qui par contre, si rien n’est fait pour

l’éviter, pourrait poser des risques de dommages matériels.

POUR TOUTES QUESTIONS OU COMMENTAIRES RELATIFS(VES)

À L’OUTIL OU À PROPOS DE TOUT AUTRE OUTIL D

eWA LT,

COMPOSER SANS FRAIS LE : 1-800-4-D

eWA LT (1-800-433-9258)



AVERTISSEMENT : Ne pas utiliser cet appareil avant d’avoir lu

et compris le mode d’emploi ainsi que l’intégralité des directives de

sécurité, d’utilisation et d’entretien.

AVERTISSEMENT :

Ce produit contient des produits chimiques

reconnus par l’État de la Californie comme étant cancérigènes

et pouvant entraîner des anomalies congénitales ou d’autres

problèmes liés aux fonctions reproductrices. Se laver les mains

après toute manipulation.

AVERTISSEMENT :

Certaines poussières contiennent des

produits chimiques reconnus par l’État de la Californie comme

cancérigènes et pouvant entraîner des anomalies congénitales

et d’autres problèmes liés aux fonctions reproductrices, tels que

l’amiante et le plomb contenus dans les peintures au plomb.



DANGER :

RISQUE D’EXPLOSION OU D’INCENDIE

CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER

 • Ilestnormalquedes

contacts électriques dans le

moteur et le manocontacteur

fassent une étincelle.

 • Faitestoujoursfonctionner

le compresseur dans une

zone bien aérée sans matière

combustible, essence ou

vapeur de solvant.

La page charge ...

DeWalt D55167 Manuel utilisateur

Ce manuel convient également à

DeWalt D55167 Manuel utilisateur

dans d''autres langues

Documents connexes