GE GBS20EGHBB Guide d'installation

GEAppliances.com

Refrigerators

Bottom Freezer

200D9366P004 49-60539-1 09-11 GE

Safety Instructions . . . . . . . . . . .2, 3

Operating Instructions

Automatic Icemaker . . . . . . . . . . . . . . .10

Care and Cleaning . . . . . . . . . . . . .11, 12

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Crispers and Pans . . . . . . . . . . . . . . . . . . .7

Freezer . . . . . . . . . . . . . . . . . . . . . . . . . . .8, 9

Replacing the Light Bulbs . . . . . . . . . .13

Shelves and Bins . . . . . . . . . . . . . . . . . . . .6

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . .5

Installation Instructions

Installing the Refrigerator . . . . . .15–19

Installing the Water Line . . . . . . . .28–30

Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . . . . . .14

Removing and Replacing

the Doors (Double Door

Refrigerator Models only) . . . . . . .25–27

Removing and Replacing the

Freezer Drawer . . . . . . . . . . . . . . . .20, 21

Reversing the Door Swing

(Single Door Refrigerator

Models only) . . . . . . . . . . . . . . . . . . .22–25

Troubleshooting Tips . . . . . .31–34

Normal Operating Sounds . . . . . . . . . .31

Consumer Support

Consumer Support . . . . . . . .Back Cover

Performance Data Sheet . . . . . . . . . . .41

State of California Water

Treatment Device Certificate . . . . . . .42

Warranty for Canadian

Customers . . . . . . . . . . . . . . . . . . . . . . . . .40

Warranty for U.S. Customers . . . . . . .39

Réfrigérateurs

Congélateur inférieur

Refrigeradores

Congelador inferior

Write the model and serial

numbers here:

Model # ____________________

Serial #______________________

Find these numbers on a label

on the right side, near the top of the

refrigerator compartment.

Models 20, 22 and 23

Manuel d’utilisation

et d’installation

Owner’s Manual and

Installation Instructions

Manual del

propietario e

instalación

La section française commence à la page 43

La sección en español empieza en la página 81

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:



 This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.



 Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.



 Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.



 Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.



 Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.



 In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

that releases the cubes. Do not place fingers or

hands on the automatic icemaking mechanism

while the refrigerator is plugged in.



 Unplug the refrigerator before cleaning and making

repairs.

NOTE: We strongly recommend that any servicing

be performed by a qualified individual.



 Setting either or both controls to the Off position

does not remove power to the light circuit.



 Do not refreeze frozen foods which have

thawed completely.

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous…even if they will sit for “just a few days.”

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

 Take off the doors.

 Leave the shelves in place so that children may not

easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States)

or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug

and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

2

3

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

GEAppliances.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard from

this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to

have it replaced with a properly grounded 3-prong

wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a

fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

USE OF ADAPTER PLUGS

Adapter plugs are not permitted in Canada.

4

About the controls with temperature settings.

Initially, set the refrigerator control at 5 and the freezer control at 5. Allow 24 hours for

the temperature to stabilize. Several adjustments may be required. Adjust the controls

one increment at a time, and allow 24 hours after each adjustment for the refrigerator

to reach the temperature you have set.

Setting either or both controls to 0 for digital and 0 for the refrigerator control knob

stops cooling in both the refrigerator and freezer compartments, but does not shut

off electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering the digital temperature

controls. If this film was not removed during installation, remove it now.

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

(on some models)

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

5

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

compartment.

When to Replace the Filter

The filter cartridge should be replaced

when the flow of water to the icemaker

decreases, or every six months.

Installing the Filter Cartridge

If you are replacing the cartridge, first

remove the old one. Open the cartridge

cover by pressing in on the tab at the

front and pulling down.

Remove the cartridge by slowly rotating

it counterclockwise. A small amount of

water may drip down.

CAUTION: If air has been

trapped in the system, the filter cartridge may

be ejected as it is removed. Use caution when

removing.

Remove the protective foil from the end

of the cartridge.

Lining up the arrow on the cartridge

and the cartridge holder, slowly rotate

the cartridge clockwise until it stops.

When the cartridge is properly installed,

you will feel it “click” as it locks into place.

The grip on the end of the cartridge

should be positioned vertically.

Do not overtighten.

Close the cartridge cover.

Filter Bypass Plug

You must use the filter bypass plug when a

replacement filter cartridge is not available.

The icemaker will not operate without the

filter or filter bypass plug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Website,

GEAppliances.com, or call GE Parts and

Accessories, 800.626.2002.

Filter Model GSWF

Customers in Canada should consult

the yellow pages for the nearest Mabe

Service Center.

About the water filter. (on some models) GEAppliances.com

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

6

Rearranging the Shelves

To remove:

Remove all items from the shelf.

Tilt the shelf up at the front.

Lift the shelf up at the back and bring the

shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot

on the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

About the shelves and bins.

Not all features are on all models.

Some models have wire shelves

that can be adjusted in the same

manner.

Shelves in the refrigerator compartment are adjustable.

Refrigerator Compartment

Non-Adjustable Shelves on the Door (on some models)

To remove: Lift the shelf straight up; then

pull out.

To replace: Engage the shelf in the molded

supports on the door and push down.

It will lock in place.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

7

About the crispers and pans. GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Snack Pan (on some models)

This pan can be moved to the most useful

location for your family’s needs.

To remove, slide the pan out to the stop

position, lift the pan up and past the stop

position and lift it out.

8

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

Freezer Shelves and Baskets

A shelf above the ice storage bin

A half-width basket

A deep full-width basket

NOTE: Do not fill baskets higher than the rim

of the basket. This may cause baskets to stick

or jam when opening or closing.

Basket Removal

To remove the deep full-width basket on

freezer drawer models:

Open the freezer drawer until it stops.

The freezer basket rests on the inside

tabs on the drawer slides.

Lift the basket so that it is out of all

6 slide bracket tabs.

Tilt the basket and lift out of the drawer.

When replacing the deep full-width basket:

Tilt the basket back and lower it down

into the drawer. Rotate the basket to a

horizontal position and press it down into

the 6 alignment tabs.

NOTE: Always be sure that the basket is

seated in all 6 slide bracket tabs before

sliding back into the freezer. The basket can

be turned in either direction front to back and

installed into the freezer.

To remove the half-width basket:

Pull the basket out to the stop location.

Lift the basket up at the front to release

it from the stop hooks on each side.

Lift the basket out to remove it from

the sides.

When replacing the basket, make sure that

the basket goes under the stop hooks on

each side.

NOTE: Always be sure to fully close this

basket.

About the freezer drawer. (on some models)

Not all features are on all models.

Appearance and features may vary

Appearance may vary

9

Freezer Shelf and Basket

A full-width fixed wire shelf

A full-width sliding wire basket

NOTE: Do not fill basket higher than the rim of

the basket. This may cause basket to stick or

jam when opening or closing.

Basket Removal

To remove the full-width sliding wire basket

on door models:

Open the basket out to its full extension.

Lift up the front of the basket and pull

straight out to remove.

When replacing the full-width sliding

wire basket:

Insert the wire basket into the lower liner’s

rails and push back into place.

NOTE: The full-width wire shelf is not intended

to slide.

To remove for cleaning:

Hold the shelf at the front and pull it firmly

forward.

When replacing the full-width sliding wire

shelf:

Insert the wire shelf into the upper liner’s rails

and push back into place.

About the freezer compartment. (on some models) GEAppliances.com

Not all features are on all models.

Fixed Shelf Removal

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

To remove: Lift the shelf straight up;

then pull out.

To replace: Engage the shelf in the molded

supports on the door and push down. It will

lock in place.

Non-Adjustable Shelf on Freezer Door

To remove

To replace

10

About the automatic icemaker. (on some models)

Automatic Icemaker

The icemaker will produce seven cubes per cycle—

approximately 100–130 cubes in a 24-hour period,

depending on freezer compartment temperature,

room temperature, number of door openings and

other use conditions.

See below for how to access ice and reach the

power switch.

If the refrigerator is operated before the water

connection is made to the icemaker, set the power

switch in the O (off) position.

When the refrigerator has been connected to

the water supply, set the power switch to the l (on)

position. The icemaker power light will turn green

when the freezer light switch is pressed in or when

the freezer door is closed.

The icemaker will fill with water when it cools to

15°F (–10°C). A newly installed refrigerator may

take 12 to 24 hours to begin making ice cubes.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice to allow

the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler arm,

the icemaker will stop producing ice. It is normal

for several cubes to be joined together.

If ice is not used frequently, old ice cubes will

become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

NOTE: Set the power switch to the O (off) position

if the water supply is shut off.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Icemaker

Feeler Arm

Power

Switch

Green

Power

Light

Accessing Ice and Reaching

the Power Switch

To reach the icemaker power switch, pull

the shelf above the ice bin straight out. Always

be sure to replace the shelf.

To access ice, simply pull the bin forward.

To access ice.

Shelf

Ice Bin

To reach the power switch.

Shelf

Ice Bin

Icemaker Accessory Kit

If your refrigerator did not come already equipped

with an automatic icemaker, an icemaker

accessory kit is available at extra cost.

Check the back of the refrigerator for the specific

icemaker kit needed for your model.

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

Care and cleaning of the refrigerator. GEAppliances.com

Cleaning the Outside

The door handles and trim. Clean with a

cloth dampened with soapy water. Dry with

a soft cloth. Do not use wax on the door

handles and trim.

Keep the outside clean. Wipe with

a clean cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled

dish cloth or wet towel. These may leave

a residue that can erode the paint. Do not

use scouring pads, powdered cleaners,

bleach or cleaners containing bleach

because these products can scratch and

weaken the paint finish.

The stainless steel panels and door

handles. Stainless steel (on some models)

can be cleaned with a commercially

available stainless steel cleaner. A spray-on

stainless steel cleaner works best.

Do not use appliance wax or polish on the

stainless steel.

Cleaning the Inside

To help prevent odors, leave an open box

of baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture

out of sponge or cloth when cleaning around

switches, lights or controls.

Use an appliance wax polish on the inside

surface between the doors.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water. This both cleans and

neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a thin

layer of petroleum jelly to the door gaskets

at the hinge side. This helps keep the gaskets

from sticking and bending out of shape.

Avoid cleaning cold glass shelves with hot

water because the extreme temperature

difference may cause them to break.

Handle glass shelves carefully. Bumping

tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts

in the dishwasher.

11

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

12

For long vacations or absences, remove

food and unplug the refrigerator. Clean the

interior with a baking soda solution of one

tablespoon (15 ml) of baking soda to one

quart (1 liter) of water. Leave the doors open.

Set the icemaker power switch to the O (off)

position and shut off the water supply to

the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

Care and cleaning of the refrigerator.

Preparing for Vacation

Preparing to Move

Secure all loose items such as base grille,

shelves and drawers by taping them securely

in place to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back

of the refrigerator against the hand truck.

This could damage the refrigerator. Handle

only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Raise the leveling legs located at the bottom

front of the refrigerator.

Pull the refrigerator straight out and return it

to position by pushing it straight in. Moving

the refrigerator in a side direction may result

in damage to the floor covering or

refrigerator.

Lower the leveling legs until they touch the

floor.

When pushing the refrigerator back, make

sure you don’t roll over the power cord or

icemaker supply line (on some models).

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

13

Refrigerator Lights

CAUTION: Light bulbs may

be hot.

Unplug the refrigerator.

To remove the light shield, grasp the

shield at the back and pull out to release

the tabs at the back.

Rotate the shield down and then forward

to release the tabs at the front of the

shield.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

NOTE: Appliance bulbs may be ordered from

GE Parts and Accessories, 800.626.2002.

Freezer Light

Replacing the light bulbs. GEAppliances.com

Turning the control to the 0ff position does not remove power to the light circuit.

Appearance may vary

CAUTION: Light bulbs may

be hot.

Unplug the refrigerator.

The bulb is located at the top of the

freezer inside a light shield. To remove

the shield, grasp the shield at the back

and pull out to release the tabs at the

back.

Rotate the shield down and then forward

to release the tabs at the front of the

shield.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

Installation

Refrigerator

Instructions

Models 20 and 22

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT — Save these instructions

for local inspector’s use.

•

IMPORTANT — Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

20 minutes

Water Line Installation

30 minutes

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS

If the refrigerator will not fit through a doorway,

the refrigerator door and freezer drawer can be

removed.

• To remove the refrigerator door, see Step 1 in

the Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing

the Freezer Drawer section.

WATER SUPPLY TO THE ICEMAKER AND DISPENSER

(ON SOME MODELS)

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. A GE water supply kit

(containing tubing, shutoff valve, fittings and instructions) is

available at extra cost from your dealer, by visiting our

Website at GEAppliances.com (in Canada at

www.geappliances.ca) or from Parts and Accessories,

800.626.2002 (In Canada 1.888.661.1616).

TOOLS YOU MAY NEED

Adjustable Wrench

1/4” Outer Diameter

Compression Nut

and Ferrule (sleeve)

(icemaker models only)

Phillips Head Screwdriver

14

3/8” and 5/16” Socket

Ratchet/Driver

3/32”, 1/8” and 3/16” Allen

wrenches

Pencil

1/8” Drill Bit and

Electric or Hand Drill

Tape measure

1/4” Nut Driver

Wire Cutters

Level

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature

will go above 100°F (37°C) because it will not perform

properly.

• Install it on a floor strong enough to support it fully

loaded.

CLEARANCES

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

Standard Depth

Models

Sides 1/8” (3 mm)

Top 1” (25 mm)

Back 1” (25 mm)

CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(icemaker models)

A cold water supply is required for automatic

icemaker operation. If there is not a cold water

supply, you will need to provide one. See Installing the

Water Line section.

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not plugged

into the wall outlet.

• If your refrigerator does not have a water filter, we

recommend installing one if your water supply has

sand or particles that could clog the screen of the

refrigerator’s water valve. Install it in the water line

near the refrigerator. If using GE SmartConnect

™

Refrigerator Tubing Kit, you will need an additional

tube (WX08X10002) to connect the filter. Do not cut

plastic tube to install filter.

1

REMOVE TOP CAP (on some models)

•

IMPORTANT NOTE: This refrigerator is 34-1/2” deep.

Doors and passageways leading to the installation

location must be at least 36” wide in order to leave

the doors and handles attached to the refrigerator

while transporting it into the installation location. If

passageways are less than 36”, the refrigerator doors

and handles can easily be scratched and damaged.

The top cap and doors can be removed to allow the

refrigerator to be safely moved indoors. Start with Step A.

• If it is not necessary to remove doors, skip Step A.

Leave tape and all packaging on doors until the

refrigerator is in the final location.

• SKID REMOVAL: Tilt refrigerator to each side to

remove skid.

• NOTE: Use a padded hand truck to move this

refrigerator. Place the refrigerator on the hand truck

with a side against the truck. We strongly recommend

that TWO PEOPLE move and complete this installation.

Locate and remove the two Phillips head screws on

the top of the refrigerator. Remove the two screws

on each side at the rear of the top cap. Lift off and

remove top cap.

Remove the fresh-food door(s). Refer to Steps 1 and 3

of “Reversing the Door Swing” section or Steps 1 and

2 of “Removing the Doors” section.

Remove the bottom freezer drawer or door. Refer to

“Removing Freezer Drawer” section or Step 2 of

“Reversing the Door Swing” section.

Move refrigerator to the installation location.

A

B

C

D

15

REMOVE TOP CAP (cont.)

(on some models)

REINSTALL DOORS, DRAWERS AND TOP CAP

Carefully lower the door(s) onto the center hinge(s).

Reinstall top hinge(s). NOTE: Ensure the door is

properly aligned to the case top to avoid

readjustment of the door during top cap

reinstallation.

Place cap over the top of the refrigerator. Reinstall

the original screws in the top and back of the cap.

Reinstall the bottom freezer drawer or door. Refer to

“Replacing the Freezer Drawer” section or Step 8 of

“Reversing the Door Swing” section.

E

F

G

A

Top Hinge B

CONNECTING THE REFRIGERATOR TO

THE HOUSE WATER LINE

(cont.)

If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the

end of the tubing coming from the house cold

water supply.

If you are using the GE SmartConnect

™

tubing, the nuts are already assembled to

the tubing.

If you are using copper tubing, insert

the end of the tubing into the refrigerator

connection, at the back of the refrigerator,

as far as possible. While holding the tubing,

tighten the fitting.

If you are using GE SmartConnect

™

tubing,

insert the molded end of the tubing into the

refrigerator connection, at the back of the

refrigerator, and tighten the compression

nut until it is hand tight. Then tighten one

additional turn with a wrench. Overtightening

may cause leaks.

Fasten the tubing into the clamp provided to

hold it in position. You may need to pry open

the clamp.

One of the illustrations below will look like

the connection on your refrigerator.

Icemaker-Ready models

Icemaker-Installed Models

16

Installation Instructions

1

A

B

C

1/4 Tubing

Tubing Clamp

1/4

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

TURN ON THE WATER SUPPLY

(icemaker models)

Turn the water on at the shutoff valve (house

water supply) and check for any leaks.

2

PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in

the refrigerator, make sure the icemaker power

switch is set to the O (off) position.

See the grounding information attached to the

power cord.

3

PUT THE REFRIGERATOR IN PLACE

Move the refrigerator to its final location.

4

1/4 Copper

Tubing

1/4

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

Tubing

Clamp

LEVEL THE REFRIGERATOR

Adjustable legs at the front corners of the

refrigerator should be set so the refrigerator is

firmly positioned on the floor, and the front is

raised just enough that the door closes easily

when opened about halfway.

To adjust the leveling legs, turn the legs

clockwise to raise the refrigerator,

counterclockwise to lower it.

5

INSTALLING THE REFRIGERATOR (cont.)

Installation Instructions

REMOVE THE FRESH FOOD

DOOR HANDLE

(For placement in the installation location

or reversal of the handles – on some

models)

Stainless steel (on

some models):

REMOVING

THE DOOR

HANDLE: Loosen

the set screws

with the 3/32”

Allen wrench

and remove

the handle.

NOTE: For

Double Door

models follow

the same

procedure on

the opposite door.

Plastic handle

(on some models):

REMOVING THE DOOR HANDLE: Depress the

tab on the underside of the handle and slide

the handle up and off of the mounting

fasteners.

REVERSING THE

DOOR HANDLE

(on some

models):

• Remove

the handle

mounting

fasteners with

a 3/16” Allen

wrench and

transfer

the handle

mounting

fasteners to

the right side.

• Remove the logo badge.

• Remove and transfer the plug button to

the left side of the fresh food door. NOTE:

Use a flat plastic edge to prevent

damaging the door. Remove any adhesive

on the door with a mild detergent. Remove

the paper covering on the adhesive

backing on the logo badge prior to carefully

attaching the badge to the door.

A

6

A

B

A

B

Mounting

Fasteners

Mounting

Fasteners

Badge

(appearance may vary)

REMOVE THE FREEZER DOOR HANDLE

Stainless steel and plastic handles:

Loosen the set screws located on the

underside of the handle with the 1/8” Allen

wrench and remove the handle.

NOTE: If the handle mounting fasteners need

to be tightened or removed, use a 3/16” Allen

wrench.

A

7

A

17

ATTACH THE FREEZER DOOR HANDLE

Stainless steel and plastic handles:

Attach the handle firmly to the mounting

fasteners and tighten the set screws on

the bottom of the handle with a 1/8” Allen

wrench.

A

Installation Instructions

18

ATTACH THE FRESH FOOD

DOOR HANDLE

Stainless steel handle:

Attach the

handle to the

handle mounting

fasteners and

tighten the set

screws with a

3/32” Allen

wrench.

NOTE: For

Double Door

models follow

the same

procedure on the

opposite door.

Plastic handle:

Attach the handle to the handle mounting

fasteners by aligning the slots with the

handle mounting fasteners.

Slide it down until it is firmly locked into

position.

A

8

A

Mounting

Fasteners

(appearance may vary)

Mounting

fasteners

Slots on back of

handle

A

9

A

(appearance may vary)

INSTALLING THE REFRIGERATOR (cont.)

LEVEL THE REFRIGERATOR

The leveling legs have 2 purposes:

1) Leveling legs adjust so the refrigerator is

firmly positioned on the floor and does not

wobble.

2) Leveling legs serve as a stabilizing brake

to hold the refrigerator securely in position

during operation and cleaning. The leveling

legs also prevent the refrigerator from

tipping.

Remove the grille by removing the two Phillips

head screws.

Turn the leveling legs clockwise to raise

the refrigerator, counterclockwise to lower it.

CAUTION: To avoid possible

personal injury or property damage,

the leveling legs must be firmly touching

the floor.

Replace the base grille by inserting the two

Phillips head screws.

10

A

Installation Instructions

SET THE CONTROLS

Set the controls to the recommended setting.

11

REMOVE PACKAGING, START

ICEMAKER

(icemaker models)

A) Remove all tape, foam and protective

packing from shelves and drawers.

B) Remove the tie downs from the freezer

baskets.

C) Place half width basket onto drawer slides.

See About the freezer section for instructions.

Set the icemaker power switch to the I (on) position.

The icemaker will not begin to operate until it

reaches its operating temperature of 15°F (–9°C) or

below. It will then begin operation automatically. It

will take 2–3 days to fill the ice bin.

NOTE: In lower water pressure conditions, the

water valve may turn on up to 3 times to

deliver enough water to the icemaker.

12

Power

switch

B

C

19

20

Installation Instructions

REMOVE THE BASE GRILLE

(if needed)

If, after removing the freezer drawer and

refrigerator door, the refrigerator will still not

fit through a doorway, the base grille can be

removed.

Remove the base grille by removing the screws.

3

A

REMOVING THE FREEZER DRAWER (on some models)

REMOVE THE BASKET

Open the freezer drawer until it stops.

The freezer basket rests on a frame inside the

freezer drawer. Lift the basket up at the back.

Lift the front up and lift the entire basket up

and out of the drawer.

1

A

B

C

The freezer drawer can be removed, if needed,

to fit through tight areas.

Read these instructions completely and carefully.

REMOVE THE DRAWER FRONT

Remove the screw on each side of the railing.

2

A

REMOVE THE DRAWER FRONT (cont.)

Lift up on both sides of the freezer drawer

handle to separate the drawer railings from

the rail assemblies.

Set the drawer front on a non-scratching

surface.

Push the rail assemblies back into locking

position.

2

B

C

D

Rail Assembly

Drawer

Assembly

A

Screw

La page charge ...

GE GBS20EGHBB Guide d'installation

Ce manuel convient également à

GE GBS20EGHBB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents