Yamaha RX-V496RDS Le manuel du propriétaire

Marque: Yamaha

Modèle: RX-V496RDS

Catégorie: Récepteurs AV

Taper: Le manuel du propriétaire

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

RX-V496RDS

Natural Sound AV Receiver

Ampli-tuner audio-vidéo

RX-V496RDS

G B

1/17/0, 6:25 PM

CAUTION

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2. Install this unit in a cool, dry, clean place — away

from windows, heat sources, sources of excessive

vibration, dust, moisture and cold. Avoid sources of

humming (transformers, motors). To prevent fire or

electrical shock, do not expose the unit to rain or

water.

3. Never open the cabinet. If something drops into the

unit, contact your dealer.

4. Do not use force on switches, controls or connection

wires. When moving the unit, first disconnect the

power cord and then the wires connected to other

component. Never pull the wires themselves.

5. The openings on the cover assure proper ventilation

of the unit. If these openings are obstructed, the

temperature inside the unit will rise rapidly.

Therefore, avoid placing objects against these

openings, and install the unit in a well-ventilated area

to prevent fire and damage.

Be sure to allow a space of at least 20 cm behind,

20 cm on both sides and 30 cm above the top panel

of the unit to prevent fire and damage.

6. The voltage used must be the same as that specified

on this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for

any damage resulting from the use of this unit with a

voltage other than that specified.

7. Digital signals generated by this unit may interfere

with other component such as tuners, receivers and

TVs. Move this unit farther away from such

component if interference is observed.

8. Always set VOLUME to the “m” position before

starting the audio source play. Increase the volume

gradually to an appropriate level after playback has

been started.

9. Do not attempt to clean the unit with chemical

solvents; this might damage the finish. Use a clean,

dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before

concluding that the unit is faulty.

11. When not planning to use this unit for a long period

of time (e.g., a vacation), disconnect the AC power

cord from the wall outlet.

12. To prevent lightning damage, disconnect the AC

power cord and disconnect the antenna cable when

there is an electrical storm.

13. Grounding or polarization — Precautions should be

taken so that the grounding or polarization of the unit

is not defeated.

14. AC outlet — Do not connect audio component to the

AC outlet on the rear panel if that component

requires more power than the outlet is rated to

provide.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off. This state is called the standby

mode. In this state, this unit is designed to consume a

very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed

as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured BROWN

must be connected to the terminal which is marked with

the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

0101V496RDS_caution_EN 1/6/0, 10:19 AM2

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

FEATURES

5-Channel Power Amplification

◆ Minimum RMS Output

(0.06% THD, 20 Hz – 20 kHz)

Main: 65 W + 65 W (8 Ω)

Center: 65 W (8 Ω)

Rear: 65 W + 65 W (8 Ω)

Multi-mode Digital Sound Field

Processing

◆ Digital Sound Field Processor (DSP)

◆ Dolby Digital Decoder

◆ Dolby Pro Logic Decoder

◆ DTS Decoder

◆ CINEMA DSP: Theater-like Sound Experience by

the Combination of YAMAHA DSP Technology

and Dolby Digital, Dolby Pro Logic or DTS

◆ Automatic Input Balance Control for Dolby Pro

Logic decoding

Sophisticated FM/AM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset Editing)

◆ Multi-Functions for RDS Broadcast Reception

Other Features

◆ “SET MENU” which Provides You with 11 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other Future

Formats

◆ Video Signal Input/Output Capability

(Including S Video Connections)

◆ 2 Optical/1 Coaxial Digital Signal Input Terminals

◆ SLEEP Timer

◆ Remote Control with Preset Manufacturer Codes

INTRODUCTION

CONTENTS

PREPARATION

SPEAKER SETUP....................................................... 8

CONNECTIONS.......................................................... 9

ADJUSTING THE SPEAKER BALANCE ............ 18

BASIC OPERATION

PLAYING A SOURCE .............................................. 20

DIGITAL SOUND FIELD PROCESSOR (DSP)

EFFECT .................................................................. 24

SOUND FIELD PROGRAM .................................... 25

TUNING ..................................................................... 28

RECEIVING RDS STATIONS................................. 32

RECORDING A SOURCE ON TAPE, MD OR

VIDEO CASSETTE ............................................... 35

ADVANCED OPERATION

SET MENU................................................................. 36

DELAY TIME AND SPEAKER

OUTPUT LEVELS ................................................. 40

SLEEP TIMER .......................................................... 42

PRESET REMOTE CONTROL .............................. 43

APPENDIX

TROUBLESHOOTING ............................................ 50

SPECIFICATIONS.................................................... 53

GLOSSARY................................................................ 54

INDEX ........................................................................ 55

INTRODUCTION

FEATURES .................................................................. 1

CONTENTS ................................................................. 1

GETTING STARTED ................................................. 2

CONTROLS AND FUNCTIONS ............................... 4

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic” and the

double-D symbol are trademarks of Dolby

Laboratories. Confidential Unpublished Works.

rights reserved.

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued and

pending. “DTS”, “DTS Digital Surround”, are trademarks of

y indicates a tip for your operation.

0102V496RDS01-07_EN 1/6/0, 10:19 AM1

GETTING STARTED

Checking the Package Contents

Check that the following items are included in your package.

Remote control Batteries (AAA, R03, UM-4 type) 75-ohm/300-ohm antenna adapter

(U.K. model only)

Indoor FM antenna

AM loop antenna

Battery Installation in the Remote

Control

1 Turn the remote control over and slide the

battery compartment cover in the direction of

the arrow.

2 Insert the batteries (AAA, R03 or UM-4 type)

according the polarity markings on the inside

of the battery compartment.

3 Close the battery compartment cover.

Battery Replacement

If the remote control operates only when it is close to the

unit, the batteries are weak. Replace all the batteries with

new ones.

Be sure to replace the batteries within about two minutes.

If it takes longer than two minutes, the codes preset for

the remote control will return to the factory settings.

(Refer to pages 43 to 49 about the remote control.)

Notes

• Use only AAA, R03 or UM-4 batteries for replacement.

• Be sure the battery polarity is correct. (See the illustration inside

the battery compartment.)

• Remove the batteries if the remote control will not be used for an

extended period of time.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

Quick reference card

Connection guide

0102V496RDS01-07_EN 1/6/0, 10:19 AM2

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Using the Remote Control

The remote control transmits a directional infrared beam. Be

sure to aim the remote control directly at the infrared sensor

during operation. When the sensor is covered or there is a

large object between the remote control and the sensor, the

sensor cannot receive signals. The sensor may not be able to

receive signals properly when it is exposed to direct sunlight

or a strong artificial light (such as a fluorescent or strobe

light). In this case, change the direction of the light or

reposition the unit to avoid direct lighting.

Notes

• Handle the remote control with care.

• Do not spill water, tea or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following

conditions:

– high humidity or temperature such as near a heater, stove or

bath;

– dusty places; or

– extremely low temperature.

GETTING STARTED

Remote control

sensor

Within approximately 6 m

(20 feet)

0102V496RDS01-07_EN 1/6/0, 10:19 AM3

–

12 3 4 65

7890qwerty

uiopasdf

6VOLUME

Turn this control to turn up or down the volume.

7 PHONES jack

Connect the headphones to the PHONES jack. You can

listen to the sound to be output from the main speakers

through the headphones.

When using headphones only, set both SPEAKERS A and B

to the OFF position and press EFFECT to turn off the effect

speakers (center and rear) (so that no DSP program name

appear on the display).

8 SPEAKERS

Set A or B (or both A and B) to the ON position for the main

speaker system (connected to this unit) that you want to use.

Set the button(s) to the OFF position for the main speaker

system that you don’t want to use.

9 PROGRAM selector

Press l or h to select a DSP program when the effect

speakers (center and rear) are turned on. The name of the

selected program appears on the display.

0 EFFECT

Press this button to turn on or off the effect speakers (center

and rear). If you turn them off, all Dolby Digital and DTS

audio signals are directed to the right and left main

speakers. In that case, the output levels of the right and left

speakers may not match.

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Press this switch to turn on the power of this unit or to set

this unit in the standby mode. Before turning the power on,

set VOLUME to the “m” position.

Standby mode

In this mode, this unit consumes a very small quantity of

power to receive infrared-signals from the remote

control.

2 Remote control sensor

This receives signals from the remote control.

3 Display

This shows various information. (Refer to page 6 for

details.)

4 INPUT MODE

Press this button to select the input mode among AUTO,

DTS and ANALOG for the DVD/LD, TV/digital TV and

satellite tuner sources.

5 INPUT SELECTOR

Turn this selector to select the input source (TUNER, CD,

PHONO, V-AUX, VCR, SAT/D-TV, DVD/LD) that you

want to listen to or watch. The arrow for the selected input

source indicator lights up on the display.

0102V496RDS01-07_EN 1/19/0, 10:26 AM4

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

q Tone controls

These controls are only effective for the sound from the

main speakers.

a) BASS

Turn this control clockwise to increase or counterclockwise

to decrease the low-frequency response. The “0” position

produces a flat response.

b) TREBLE

Turn this control clockwise to increase or counterclockwise

to decrease the high-frequency response. The “0” position

produces a flat response.

w TAPE/MD MON / EXT. DECODER

Press this button to select a tape or an MD source. The

“TAPE/MD MONITOR” indicator lights up on the display.

When you press the button next, the “TAPE/MD

MONITOR” indicator goes off, “EXT. DECODER” appears

on the display and you can listen to a source connected to

the EXTERNAL DECODER INPUT terminals.

e BALANCE

This control is only effective for the sound from the main

speakers.

Turn the control to adjust the balance of the output volume

from the right and left main speakers to compensate for

sound imbalance caused by the speaker location or listening

room conditions.

r A/B/C/D/E

Press this button to select one of a group (A to E) of preset

stations.

t PRESET/TUNING

When “ z ” appears

This button is used to select a preset station number (1 to 8).

Press h to select a higher and l to select a lower preset

station number.

When “ z ” goes off

This button is used for tuning. Press h to tune in to higher

frequencies, and l to tune in to lower frequencies.

When this unit is in the PTY SEEK mode, press this button

to select a program type.

y PRESET/TUNING, EDIT

Press this button to turn on or off “ z ” on the display and

switch the function between for storing a broadcasting

station (preset tuning) and for tuning. This button is also

used to exchange the assignment of two preset stations with

each other.

u FM/AM

Press this button to switch the reception band between FM

and AM.

i MEMORY (MAN’L/AUTO FM)

Press this button to store the broadcasting stations. Hold

down this button for more than three seconds to begin

automatic preset tuning.

o TUNING MODE (AUTO/MAN’L MONO)

Press this button to switch the tuning mode between

automatic and manual. To use the automatic tuning method,

press this button so that the “AUTO” indicator lights up on

the display. To use the manual tuning method, press this

button so that the “AUTO” indicator goes off.

p RDS MODE/FREQ

When an RDS station is received, press this button to

change the display mode among the PS mode, PTY mode,

RT mode, CT mode (if the station offers those RDS data

services) and/or frequency display mode in turn.

a EON

Press this button to select the desired program type (NEWS,

INFO, AFFAIRS, SPORT) when you want to tune in to a

radio program of that type automatically.

s PTY SEEK MODE

Press this button to set the unit in the PTY SEEK mode.

d PTY SEEK START

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode.

f VIDEO AUX terminals

Connect an auxiliary audio or video input source such as a

camcorder to these terminals. Use INPUT SELECTOR to

select the source connected to these terminals.

CONTROLS AND FUNCTIONS

0102V496RDS01-07_EN 1/6/0, 10:19 AM5

Display

8 MEMORY indicator

This flashes for about five seconds after pressing

MEMORY. During this period, the displayed station can be

stored in the memory.

9 RDS mode indicators

The name(s) of the RDS data offered by the currently

received RDS station light(s) up. Illumination of the red

indicator next to the RDS data name shows that the

corresponding RDS mode is now selected.

0 AUTO indicator

This lights up when the unit is in the automatic tuning

mode.

q PTY HOLD indicator

This lights up while searching for stations in the PTY SEEK

mode.

w EON indicator

This lights up when an RDS station that offers the EON data

service is being received.

e Program type name indicators

The name of the selected program type lights up when the

“EON” indicator lights up.

r STEREO indicator

This lights up when an FM stereo broadcast with sufficient

signal strength is being received.

t Signal-level indicator

This indicates the signal level of the station being received.

If multipath interference is detected, the indication

decreases.

y SLEEP indicator

This lights up while the built-in SLEEP timer is on.

CONTROLS AND FUNCTIONS

1 t indicator

The “t” indicator lights up when the built-in DTS

decoder is turned on.

2 DSP program indicators

The name of the selected DSP program lights up in the

following cases:

• When the tuner is selected as the input source.

• When DSP program No. 2, 3 or the subprogram

“ENHANCED” of No.1 is selected.

3 Multi-information display

This display shows various information: for example the

name of the selected DSP program and the various settings

during adjustment with the SET MENU. The current station

frequency and band (FM or AM) also appear when the tuner

is selected as the input source.

4 Input source indicators

One of the arrows for these indicators lights up depending

on which source is selected.

5 TAPE/MD MONITOR indicator

This lights up when the tape deck or MD recorder, etc. is

selected as the input source by pressing TAPE/MD MON /

EXT. DECODER (or TAPE/MD).

6 g and o indicators

“ g ” lights up when the built-in Dolby Digital

decoder is on and the signals of the selected source encoded

with Dolby Digital are not in 2-channel. “ o ”

lights up when the built-in Dolby Pro Logic decoder is on.

7 x indicator

“ x ” lights up when the built-in digital sound

field processor is on.

0102V496RDS01-07_EN 1/12/0, 10:26 AM6

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Remote Control

1 Indicator

This flashes in red when pressing a button on the remote

control. If it flashes rapidly several times, press the selected

button again.

2 Component selector buttons

Press one of these buttons which corresponds to the

component you want to control with the remote control.

(The proper code must be set for your component. Refer to

“Setup codes” on page 48.) When the component selector

button has been pressed, the remote control is set to that

component operation mode.

3 POWER

Each time you press this button, the unit switches between

the power on and standby mode.

4 TEST

Press this button to output the test tone for each speaker.

5 A/B/C/D/E, PRESET +/–

These buttons are used to select a preset station.

A/B/C/D/E: To select one of a group (A to E) of preset

stations

PRESET +/–: To select a preset station number (1 to 8)

6 MUTE

Press this button to mute the sound. To cancel mute, press

this button again.

7 VOLUME

These buttons are used to adjust the volume level.

u: To turn up the volume

d: To turn down the volume

8 SLEEP

Press this button to set the SLEEP timer.

9 +/–

These buttons adjust the settings of the SET MENU and

TIME/LEVEL mode.

0 TIME/LEVEL

Press this button to select the items in the TIME/LEVEL

mode.

q Input selector buttons

These buttons select the input source.

CD: To play a CD

TUNER: To listen to an FM (RDS) or AM broadcast

TAPE/MD: To play a tape or MD

DVD/LD: To play a DVD or LD

SAT/D-TV: To watch a TV or satellite broadcast

VCR: To play a video cassette

PHONO: To play an analog record

V-AUX: To use a camcorder

EXT. DEC.: To play other multi-channel source

w EFFECT

Press this button to turn on or off the effect speakers (center

and rear).

e PRG+, PRG–

Press these buttons to select a DSP program.

r SET MENU

Press this button to select the items in the SET MENU.

CONTROLS AND FUNCTIONS

TV VOLUME

TV INPUT

Press AMP(TUNER).

This section describes basic operation of this unit with the

remote control. First, press AMP(TUNER) on the

component selector. Refer to “PRESET REMOTE

CONTROL” on page 43 for full details.

0102V496RDS01-07_EN 1/19/0, 10:26 AM7

SPEAKER SETUP

Speaker Placement

Refer to the following diagram when you place the

speakers.

Speakers to Be Used

This unit is designed to provide the best sound-field quality

with a 5-speaker system, using main speakers, rear speakers

and a center speaker. If you use different brands of speakers

(with different tonal qualities) in your system, the tone of a

moving human voice and other types of sound may not shift

smoothly. We recommend that you use speakers from the

same manufacture or speakers with the same tonal quality.

The main speakers are used for the main source sound plus

the effect sounds. They will probably be the speakers from

your present stereo system. The rear speakers are used for

the effect and surround sounds, and the center speaker is for

the center sounds (dialog, vocals, etc.). If for some reason it

is not practical to use a center speaker, you can do without

it. Best results, however, are obtained with the full system.

The main speakers should be high-performance models and

have enough power-handling capacity to accept the

maximum output of your audio system. The other speakers

do not have to be equal to the main speakers. For precise

sound localization, however, it is ideal to use high-

performance models that can reproduce sounds over the full

range for the center speaker and the rear speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is effective

not only for reinforcing bass frequencies from any or all

channels, but also for reproducing the LFE (low frequency

effect) channel with high fidelity when playing back a

source encoded with Dolby Digital or DTS. The YAMAHA

Active Servo Processing Subwoofer System is ideal for

natural and lively bass reproduction.

Main

speaker (L)

Center speaker

Main speaker (R)

Subwoofer

Rear speaker (L)

Rear speaker (R)

1.8 m

■ Main speakers

Place the right and left main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the TV monitor should be the

same.

■ Rear speakers

Place these speakers behind your listening position, facing

slightly inwards, nearly 1.8 m (approx. 6 feet) above the

floor.

■ Center speaker

Align the front face of the center speaker with the front face

of your TV monitor. Place the speaker as close to the

monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the sound will be heard from the

right and left main speakers. In that case, “CENTER SP” in the

SET MENU is set to the NONE position. (Refer to page 37 for

details.)

■ Subwoofer

The position of the subwoofer is not so critical, because low

bass sounds are not highly directional. But it is better to

place the subwoofer near the main speakers. Turn it slightly

toward the center of the room to reduce the wall reflections.

CAUTION

Some types of speakers interfere with a TV monitor. If

this problem occurs, move the speakers away from the

monitor. If you cannot avoid installing the center speaker

or subwoofer near the TV monitor, use magnetically

shielded speakers.

PREPARATION

0103V496RDS08-19_EN 1/6/0, 10:19 AM8

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been

completed.

Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different terminal names. Refer to the instructions for each

component to be connected to this unit.

When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect

it to the terminals with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products.

Use RCA-type pin plug cables for connecting audio/video components with the exception described later.

The input and output terminals for pin plugs can be distinguished as follows:

Yellow video signals (composite)

White analog audio signals for the left channel

Red analog audio signals for the right channel

coaxial digital signals

After completing all connections, check them again to make sure they are correct.

MAINS

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

REAR

(SURROUND)

CENTER

MAIN

––++

–

Connecting an Audio

Component (page 12)

Connecting a Video

Component (page 13)

IMPEDANCE SELECTOR

switch (page 17)

Connecting the

Antenna (page 10)

Connecting to an External

Decoder (page 14)

Connecting Speakers

(page 15)

Connecting the Power

Supply Cords (page 17)

(Europe model)

V V

C C

0103V496RDS08-19_EN 1/6/0, 10:19 AM9

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal

strength. However, a properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may improve the quality.

Connect each antenna correctly to the designated terminals.

■ Indoor FM antenna (included)

Firmly insert the connector into the FM ANT terminal. The

indoor FM antenna is only a simple antenna. For reception

with better sound quality, installing the outdoor FM antenna

(commercially available) is recommended.

Note

• Do not connect an outdoor FM antenna and the indoor FM

antenna at the same time.

■ Outdoor FM antenna

You may be unable to obtain good FM radio reception

depending on your local conditions (distance from the

broadcasting station, interposing buildings and

mountains, etc.). Consult your dealer or authorized service

center and be sure to install an antenna that suits your local

conditions.

Install the outdoor FM antenna (commercially available) in

a high place as far away from any roads as possible to avoid

being affected by automobile ignition noise.

■ Connecting a coaxial cable to the included 75-ohm/300-ohm antenna

adapter (U.K. model only)

1 Open the cover of the included 75-ohm/

300-ohm antenna adapter.

2 Cut the external sleeve of the 75-ohm coaxial

cable and prepare it for connection.

3 Cut the lead wire and remove it.

4 Insert the cable wire into the slot, and clamp it

with pliers.

5 Snap the cover into place.

CONNECTIONS

75-ohm/300-ohm antenna

adapter (included for U.K.

model)

75-ohm coaxial cable

75-ohm/300-ohm antenna

adapter (included for U.K.

model)

300-ohm feeder

Unit: mm

(inch)

11 (7/16)

8 (5/16)

6 (1/14)

Lead wire

Insert the wire

into the slot.

Clamp with

pliers.

Clamp with

pliers.

Cover

Indoor FM

antenna

0103V496RDS08-19_EN 1/6/0, 10:20 AM10

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

■ AM loop antenna (included)

The AM loop antenna can be removed from the stand and

attached to a wall, etc. However, note that the reception

sensitivity may deteriorate if the antenna is attached to a

metal or steel reinforced wall.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

■ Connecting the AM loop antenna

1 Press the tab and unlock the terminal hole.

2 Insert the AM loop antenna lead wires into the

AM ANT and GND terminals.

3 Return the tab to its original position to lock

the lead wires. Lightly pull the lead wires to

confirm a good connection.

4 Attach the loop antenna to the antenna stand.

5 Orient the AM loop antenna so that the best

reception is obtained.

■ Outdoor AM antenna

If you cannot obtain good reception with the AM loop

antenna, connect 5 m to 10 m of vinyl covered wire to the

AM ANT terminal and extend it outdoors from a window.

■ Ground (GND terminal)

For maximum safety and minimum interference, connect

the antenna GND terminal to a good earth ground. A good

earth ground is a metal stake driven into moist earth.

CONNECTIONS

Antenna stand

AM loop antenna

Vinyl covered wire (5 m to 10 m)

0103V496RDS08-19_EN 1/6/0, 10:20 AM11

Connecting an Audio Component

■ PHONO terminals

These terminals are used to connect a turntable with an MM

or high-output MC cartridge. If you have a turntable with a

low-output MC cartridge, use an inline boosting transformer

or MC head amplifier when connecting to these terminals.

Connecting the ground (earth) wire of the turntable to the GND

terminal will normally minimize hum, but in some cases, better

results may be obtained with the ground wire disconnected.

CONNECTIONS

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

Tape deck or

MD recorder

L R

L R L R

OUTPUT

OUTPUT LINE OUT LINE IN

GND

Turntable

(Europe model)

CD player

Analog signal

Signal flow

0103V496RDS08-19_EN 1/6/0, 10:20 AM12

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Connecting a Video Component

■ Audio signal terminals

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

■ Video signal terminals

Be sure to connect the input (IN) and output (OUT)

properly.

■ Digital audio signal terminals

If your DVD/LD player, TV/digital TV or satellite

tuner, etc. has coaxial or optical digital signal output

terminals, they can be connected to this unit’s COAXIAL

and/or OPTICAL digital signal input terminals. To make a

connection between the optical digital signal terminals,

remove the cover from each terminal, and then connect

them by using a commercially available optical fiber cable

that conforms to EIA standards. Other cables might not

function correctly.

When making connections between the digital signal

terminals, you should connect the components to the same-

named analog audio signal terminals of this unit, because a

digital signal cannot be recorded by a tape deck, MD

recorder or VCR connected to this unit.

■ TV monitor with a 21-pin connector

Make a connection as shown above with a commercially

available SCART-plug connector cable.

Notes

• Be sure to attach the covers when the OPTICAL terminals are not

being used in order to protect them from dust.

• If your LD player has a Dolby Digital RF signal output terminal,

be sure to use the RF demodulator (separately purchased).

• No sound will be heard when connecting your LD player’s Dolby

Digital RF signal output terminal directly to this unit’s COAXIAL

DVD/LD digital signal input terminal.

• The input signal from the DVD/LD input terminals is selected in

the following order of priority with the input mode set to AUTO:

COAXIAL terminal → OPTICAL terminal → Analog terminal.

Refer to page 22 for details.

• All digital signal input terminals are applicable to sampling

frequencies of 32 kHz, 44.1 kHz and 48 kHz.

CONNECTIONS

L R

L R V V

ANALOG

AUDIO OUT

AUDIO

OUT

AUDIO

VIDEO

OUT

VIDEO

ANALOG

AUDIO OUT

VIDEO

OUT

VIDEO

OUT

COAXIAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

DVD/LD player TV/digital TV, satellite tuner, cable TV

(Europe model)

VCR

Analog signal

Video signal

Digital signal

(optical)

Digital signal

(coaxial)

Signal flow

TV monitor

SCART-plug

No connection

0103V496RDS08-19_EN 1/6/0, 10:20 AM13

■ S VIDEO terminals

If your VCR, TV monitor or DVD/LD player has “S” (high-

resolution) video terminals, they can be connected to this

unit’s S VIDEO terminals. Connect the VCR’s “S” video

input and output terminals to this unit’s S VIDEO VCR

OUT and IN terminals, respectively. Connect the monitor’s

“S” video input terminal to this unit’s S VIDEO MONITOR

OUT terminal. Connect the DVD/LD player’s “S” video

output terminal to this unit’s S VIDEO DVD/LD terminal.

Otherwise, connect the composite video terminals of your

VCR, TV monitor or DVD/LD player to this unit’s

composite video terminals.

Notes

• Use a special S VIDEO cable (commercially available) for the S

VIDEO connection.

• If video signals are input from both the S VIDEO input and

composite input terminals, the signals will be directed to their

respective output terminals.

■ VIDEO AUX terminals (on the front panel)

These terminals are used to connect any video input source

such as a camcorder to this unit.

Connecting to an External Decoder

This unit has additional 6-channel audio signal input

terminals for connecting an external decoder to this unit.

Connect the 6-channel audio signal output terminals of the

decoder to the EXTERNAL DECODER INPUT terminals

of this unit.

Notes

• When a source connected to these terminals is selected, the digital

sound field processor cannot be used.

• The settings of “CENTER SP”, “REAR SP”, “MAIN SP” and

“BASS OUT” in the SET MENU have no effect on a source

connected to these terminals. The setting of “MAIN LVL” is

effective. (Refer to pages 37 and 38 for details.)

CONNECTIONS

L RV

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

Camcorder

S VIDEO OUT

S VIDEO

OUT

S VIDEO IN

DVD/LD player

TV Monitor

VCR

S Video signal

Signal flow

L R L R

MAIN

OUT

SURROUND

OUT

CENTER

OUT

SUBWOOFER

OUT

External decoder

(Europe model)

0103V496RDS08-19_EN 1/6/0, 10:20 AM14

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Connecting Speakers

Be sure to connect the right channel (R), left channel (L),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTIONS

• Use speakers with the specified impedance shown on

the rear panel of this unit.

• Do not let the bare speaker wires touch each other and

do not let them touch any metal part of this unit. This

could damage the unit and/or speakers.

■ Main speaker terminals

One or two speaker systems can be connected to these

terminals. If you use only one speaker system, connect it to

either of the SPEAKERS A or B terminals.

■ Rear speaker terminals

A rear speaker system can be connected to these terminals.

■ Center speaker terminal

A center speaker can be connected to this terminal.

CONNECTIONS

MAINS

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

REAR

(SURROUND)

CENTER

MAIN

––++

–

Main speakers A

Right Left

Main speakers B

Right Left

(Europe model)

Center speaker Rear speakers

Right Left

Subwoofer connection

If you have a subwoofer with built-

in amplifier, including the

YAMAHA Active Servo Processing

Subwoofer System, connect the

input terminal of the subwoofer

system to the SUBWOOFER

OUTPUT terminal of this unit.

0103V496RDS08-19_EN 1/6/0, 10:20 AM15

■ Speaker cables

1 Remove approx. 10 mm (3/8”) of insulation

from each of the speaker cable.

2 Twist the exposed wires of the cable together

to prevent short circuits.

■ Connecting to the MAIN SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side of

each terminal.

3 Tighten the knob to secure the wire.

■ Connecting to the REAR and CENTER SPEAKERS terminals

1 Open the tab.

2 Insert one bare wire into the hole of each

terminal.

3 Return the tab to secure the wire.

CONNECTIONS

10 mm (3/8”)

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

0103V496RDS08-19_EN 1/6/0, 10:20 AM16

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

IMPEDANCE SELECTOR Switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise the unit may be

damaged.

If this unit fails to turn on when STANDBY/ON is pressed, the IMPEDANCE SELECTOR switch may not be fully slide

to either position. If so, slide the switch to either position fully when this unit is in the standby mode.

Select the right or left position according to the impedance of speakers in your system. Be sure to move this switch only

when this unit is in the standby mode.

Connecting the Power Supply Cords

After completing all connections, connect the AC power

cord to an AC power outlet. Disconnect the AC power cord

if you will not use this unit for a long period of time.

■ AC OUTLETS (SWITCHED)

Europe model .................................................... 2 OUTLETS

U.K. model.......................................................... 1 OUTLET

Use these outlets to connect the power cords from your

components to this unit. The power to the AC OUTLET(S)

is controlled by this unit’s STANDBY/ON (or POWER).

These outlets will supply power to any connected

component whenever this unit is turned on. The maximum

power (total power consumption of components) that can be

connected to the AC OUTLET(S) is 100 W.

If you use left position right position

Center

speaker

The impedance must be 6 Ω

or higher.

The impedance must be 8 Ω

or higher.

Rear

speakers

The impedance of each

speaker must be 6 Ω or

higher.

The impedance of each

speaker must be 8 Ω or

higher.

If you use two pairs of main

speakers, the impedance of

each speaker must be 8 Ω or

higher.

If you use two pairs of main

speakers, the impedance of

each speaker must be 16 Ω or

higher.

Main

speakers

If you use one pair of main

speakers, the impedance of

each speaker must be 4 Ω or

higher.

If you use one pair of main

speakers, the impedance of

each speaker must be 8 Ω or

higher.

CONNECTIONS

(Europe model)

MAINS

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

SWITCHED

(Europe model)

To AC outlet

MAINS

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

IMPEDANCE

SELECTOR

0103V496RDS08-19_EN 1/6/0, 10:20 AM17

Using the Test Tone

The adjustment of each speaker sound output level should

be performed at your listening position with the remote

control. After completing the adjustments, use VOLUME

(u/d) at your listening position to check if the adjustments

are satisfactory.

1 Press AMP(TUNER) on the

component selector.

2 Press TEST.

“TEST LEFT” appears on the display.

3 Turn up the volume.

You will hear a test tone (like pink noise) from each

speaker for about two seconds in following order: left

main speaker, center speaker, right main speaker, right

rear speaker and left rear speaker. The display changes

as shown below.

Notes

• If the test tone cannot be heard, turn down the volume, set the unit

in the standby mode and check the speaker connections.

• If the test tone cannot be heard from the center speaker, check the

setting of “CENTER SP” in the SET MENU.

This procedure lets you adjust the sound output level

balance between the main, center and rear speakers by using

the built-in test tone generator. When this adjustment is

performed, the sound output level heard at the listening

position will be the same from each speaker. This is

important for the best performance of the digital sound field

processor, the Dolby Pro Logic decoder, Dolby Digital

decoder and DTS decoder.

Before You Start Adjusting

1 Set VOLUME to the “m”

position.

2 Turn the power on.

3 Press SPEAKERS A or B

to select the main

speakers to be used.

If you use two main speaker

systems, press both A and B.

4 Set BASS, TREBLE and BALANCE to the “0”

position.

ADJUSTING THE SPEAKER BALANCE

–+–+

2,7

TEST

LEFT

TEST

RIGHT

TEST L SUR. TEST R SUR.

TEST CENTER

0103V496RDS08-19_EN 1/6/0, 10:20 AM18

La page charge ...

Yamaha RX-V496RDS Le manuel du propriétaire

Marque: Yamaha

Modèle: RX-V496RDS

Catégorie: Récepteurs AV

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha RX-V496RDS Manuale del proprietario
English: Yamaha RX-V496RDS Owner's manual
Deutsch: Yamaha RX-V496RDS Bedienungsanleitung
Nederlands: Yamaha RX-V496RDS de handleiding
dansk: Yamaha RX-V496RDS Brugervejledning
svenska: Yamaha RX-V496RDS Bruksanvisning
Türkçe: Yamaha RX-V496RDS El kitabı
română: Yamaha RX-V496RDS Manualul proprietarului

Yamaha RX-V496RDS Le manuel du propriétaire

Yamaha RX-V496RDS Le manuel du propriétaire

dans d''autres langues

Documents connexes