GE ZBD6905GSS Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur
Owner’s
Manual
Chef’s Washer
ZBD6605
ZBD6905
ZBD7005
ZBD7105
2
Consumer Information
Chef’s Washer
Your new Monogram Chef’s Washer makes an eloquent statement of style, convenience and
kitchen planning flexibility. Whether you chose it for its purity of design, practical features or
assiduous attention to detail–or for all of these reasons–you’ll find that your Monogram Chef’s
Washer’s superior blend of form and function will delight you for years to come.
The information on the following pages will help you operate and maintain your Chef’s
Washer properly.
If you have any other questions, visit our Website at: monogram.com
Introduction
Contents
Appliance Registration . . . . . . . . . . . .3, 31, 32
Care and Cleaning . . . . . . . . . . . . . . . . .18–21
Consumer Services . . . . . . . . . . . . . . . . . .3, 26
Model and Serial Number Location . . . . . . .3
Operating Instructions . . . . . . . . . . . . . . .8–17
Control Panel and Settings for
ZBD6605 . . . . . . . . . . . . . . . . . . . . . . . .8, 9
Control Panel and Settings for
ZBD6905 . . . . . . . . . . . . . . . . . . . . . .10, 11
Control Panel and settings for
ZBD7005 and ZBD7105 . . . . . . . . . . .12, 13
Tone Silencing . . . . . . . . . . . . . . . . . . . . .14
Clean Sensor . . . . . . . . . . . . . . . . . . . . . .14
Auto Memory . . . . . . . . . . . . . . . . . . . . . .14
Child Lockout Mode . . . . . . . . . . . . . . . .14
Water Temperature . . . . . . . . . . . . . . . . .15
Rinse Agent . . . . . . . . . . . . . . . . . . . . . . .15
Detergents . . . . . . . . . . . . . . . . . . . . . . . .15
Dishwasher Racks . . . . . . . . . . . . . . . .16, 17
Problem Solver . . . . . . . . . . . . . . . . . . . .22–25
Safety Instructions . . . . . . . . . . . . . . . . . . .4–7
USA Warranty . . . . . . . . . . . . . . . . . . . . . . . .27
Canada Warranty . . . . . . . . . . . . . . . . . . . . .28
3
Consumer Information
Chef’s Washer
Before
using
your
Chef’s
Washer
Read this manual carefully. It is intended
to help you operate and maintain your new
Chef’s Washer properly.
Keep it handy for answers to your questions.
If you don’t understand something or need
more help, there is a list of toll-free consumer
service numbers included in the back section
of this manual.
OR
Visit our Website at: monogram.com
Write
down the
model &
serial
numbers
You can find the model and serial numbers
at the inside upper left tub flange.
Before sending in this card, please write these
numbers here:
Model Number
Serial Number
Use these numbers in any correspondence or
service calls concerning your Chef’s Washer.
If you received
a damaged
Chef’s Washer
Immediately contact the dealer (or builder)
that sold you the Chef’s Washer.
Save time
& money
Before you request service, check the Problem
Solver in the back of this manual.
It lists causes of minor operating problems that
you can correct yourself.
If you
need service
To obtain service, see the Consumer Services
page in the back of this manual.
We’re proud of our service and want you to be
pleased. If for some reason you are not happy
with the service you receive, here are steps to
follow for further help.
For customers in the USA:
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases, this will solve the problem.
NEXT, if you are still not pleased, write all the
details–including your phone number–to:
Manager, Customer Relations
GE Appliances
Appliance Park
Louisville, KY 40225
For customers in Canada:
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases, this will solve the problem.
NEXT, if you are still not pleased, write all the
details–including your phone number–to:
Manager, Consumer Relations
Camco Inc.
1 Factory Lane, Suite 310
Moncton, N.B. E1C 9M3
A junked or abandoned Chef’s Washer is
dangerous…even if it will sit for “just a
few days.” If you are getting rid of your old
Chef’s Washer, please follow the instructions
below to help prevent accidents.
Before You Throw Away Your Old Chef’s Washer:
• Take off the door of the washing
compartment or remove the door latch
keeper (as shown).
4
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SÉCURITÉ IMPORTANTES
WARNING!
For your safety, the information in this manual
must be followed to minimize the risk of fire,
explosion, electric shock, or to prevent property
damage, personal injury or loss of life.
• Do not tamper with controls.
• Do not abuse, sit on, or stand on the door or
dish rack of the Chef’s Washer.
• Do not discard a Chef’s Washer without first
removing the door or removing the door latch.
• Do not store or use combustible materials,
gasoline or other flammable vapors and
liquids
in the vicinity of this or any other appliance.
• Do not allow children to play inside, on or with
this appliance or any discarded appliance.
• Do not allow children to play around the Chef’s
Washer when opening and closing the door due
to possibility of small fingers being pinched in
the door.
AVERTISSEMENT
!
Pour votre sécurité, veuillez suivre à la lettre les
directives données dans le présent manuel afin
de réduire les risques d’incendie, d’explosion ou
de chocs électriques, et prévenir les dommages
matériels et les blessures graves ou mortelles.
• Ne modifiez pas le fonctionnement des
commandes.
• Ne montez pas ou ne vous assoyez pas sur la
porte ou les paniers du lave-vaisselle du chef,
et ne les utilisez pas de façon abusive.
• Ne jetez pas un lave-vaisselle du chef sans
en avoir d’abord enlevé la porte ou enlevez
le verrou de la porte.
• N’entreposez pas et n’utilisez pas d’essence,
de vapeurs ou de liquides inflammables à
proximité de cet appareil ou de tout autre
électroménager.
• Ne laissez pas les enfants jouer avec le lave-
vaisselle du chef ni monter dessus. Ne les
laissez pas s’introduire à l’intérieur de cet
appareil ou d’un vieil appareil qui ne sert plus.
•
Ne permettez jamais à des enfants de jouer
à proximité d’un lave-vaisselle du chef quand
vous ouvrez ou fermez la porte. Ils peuvent
se coincer les doigts dans la porte.
BONNE DISPOSITION DU LAVE-VAISSELLE DU CHEF
Le lave-vaisselle du chef abandonné ou jeté est
dangereux...même s’il est abandonné «juste
pendant quelques jours». Si vous jetez votre
vieux lave-vaisselle du chef, veuillez suivre les
instructions suivantes pour prévenir tout
accident.
Avant de jeter votre vieux lave-vaisselle du chef :
• Enlevez la porte du compartiment de lavage
ou enlevez le réceptacle à verrou (comme
l’indique l’illustration).
AVERTISSEMENT! RISQUE D’ENFANT MIS AU PIÈGE
Réceptacle
à verrou
PROPER DISPOSAL OF THE CHEF’S WASHER
WARNING! RISK OF CHILD ENTRAPMENT
Door latch
keeper
5
WATER HEATER SAFETY
Under certain conditions hydrogen gas may be
produced in a water heater that has not been
used for two weeks or more. HYDROGEN
GAS IS EXPLOSIVE.
If the hot water has not been used for two
weeks or more, prevent the possibility of
damage or injury by turning on all hot water
faucets and allowing them to run for several
minutes. Do this before using any electrical
appliance which is connected to the hot water
system. This simple procedure will allow any
built-up hydrogen gas to escape. Since the gas
is flammable, do not smoke or use an open
flame or appliance during this process.
SÉCURITÉ DU CHAUFFE-EAU
Dans certaines conditions, il peut se former de
l’hydrogène à l’intérieur d’un chauffe-eau qui
n’a pas servi pendant deux semaines ou plus.
L’HYDROGÈNE EST UN GAZ EXPLOSIF.
Pour réduire les risques de dommages ou de
blessures lorsque l’eau chaude n’a pas été
utilisée depuis deux semaines ou plus, ouvrez
tous les robinets d’eau chaude et laissez l’eau
couler pendant plusieurs minutes avant
d’utiliser un appareil électrique raccordé au
système d’eau chaude. Vous éliminerez ainsi
l’hydrogène qui pourrait s’y être accumulé.
Puisqu’il s’agit d’un gaz inflammable, ne fumez
pas ou n’utilisez pas une flamme nue au cours
de ce processus.
6
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SÉCURITÉ IMPORTANTES
PROPER INSTALLATION AND MAINTENANCE
This Chef’s Washer must be properly installed
and located in accordance with the Installation
Instructions before it is used. If you did not
receive an Installation Instructions sheet with
your Chef’s Washer, you can receive one by
visiting our Website at monogram.com
.
• Connect to a grounded metal, permanent
wiring system; or run an equipment-
grounding conductor with the circuit
conductors and connect to the equipment-
grounding terminal or lead of the appliance.
• Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service representative if you are
in doubt whether the appliance is properly
grounded.
• Dispose of discarded appliances and shipping
or packing material properly.
• Do not attempt to repair or replace any part
of your Chef’s Washer unless it is specifically
recommended in this manual. All other
servicing should be referred to a qualified
technician.
• To minimize the possibility of electric shock,
disconnect this appliance from the power
supply before attempting any maintenance.
NOTE: Turning the Chef’s Washer off does
not disconnect the appliance from the power
supply. We recommend having a qualified
technician service your appliance.
INSTALLATION ET ENTRETIEN APPROPRIÉS
Avant de l’utiliser, vous devez installer
correctement ce lave-vaisselle du chef
conformément aux directives d’installation
fournies. Si vous n’avez pas reçu une feuille
de directives d’installation avec votre lave-
vaisselle du chef, vous pouvez en obtenir un
exemplaire par visiter notre site Web à l’adress
monogram.com.
• Cet appareil doit être relié à un système de
câblage électrique permanent, mis à la terre.
Sinon, un fil de mise à la terre pour
appareillage doit être installé et raccordé à la
borne ou au fil de mise à la terre de l’appareil.
• Un raccordement non approprié du fil
de mise à la terre pour appareillage peut
présenter des risques de chocs électriques.
Si vous doutez de la qualité de la mise à la
terre de votre électroménager, consultez un
représentant du Service après-vente ou un
électricien qualifié.
• Jetez de la façon appropriée les vieux
électroménagers, ainsi que le matériel
d’emballage et d’expédition.
• Ne tentez pas de réparer ou de remplacer
toute pièce de votre lave-vaisselle du chef,
à moins que cela ne soit spécifiquement
recommandé dans le présent manuel. Confiez
toutes les autres réparations à un réparateur
qualifié.
• Afin de réduire les risques de chocs électriques,
débranchez toujours l’appareil avant de le
réparer. REMARQUE : Lorsque vous mettez
la commande du lave-vaisselle du chef à OFF
(arrêt), le courant qui alimente l’appareil n’est
pas coupé. Nous vous recommandons de
confier la réparation de votre appareil à un
réparateur qualifié.
7
Use this appliance only for its intended
purpose as described in this Owner’s Manual.
CAUTION: Contents washed
in the Sanitization cycle may be hot to the
touch. Use care before unloading.
• Use only powder, tabs or liquid detergents
or wetting agents recommended for use in
a Chef’s Washer and keep them out of the
reach of children.
• Locate sharp items so that they are not
likely to damage the door seal.
• Load sharp knives with the handles up
to reduce the risk of cut-type injuries.
• Do not wash cookware unless marked
dishwasher safe or the equivalent. For
plastic items not so marked, check the
manufacturer’s recommendations.
• Non-Dishware Items: Do not wash items such
as electronic air cleaner filters, furnace filters
and paint brushes in your Chef’s Washer.
Damage to Chef’s Washer and discoloration
or staining of Chef’s Washer may result.
• Do not touch the heating element during
or immediately after use.
• Do not operate your Chef’s Washer unless
all enclosure panels are properly in place.
• Close supervision is necessary if this
appliance is used by or near children.
• Load light plastic items so they will not
become dislodged and drop to the bottom
of the Chef’s Washer–they might come into
contact with the heating element and
be damaged.
WHEN USING YOUR CHEF’S WASHER
READ AND FOLLOW THIS SAFETY
INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
N’utilisez ce lave-vaisselle du chef que pour
l’usage auquel il est destiné, comme expliqué
dans le présent Manuel d’utilisation.
MISE EN GARDE : Les
matériaux lavés selon le cycle Sanitization
peuvent être chauds. Faites attention quand
vous videz votre machine.
• N’utilisez que des détergents liquides, en
poudre ou en pastilles et les produits de rinçage
recommandés pour lave-vaisselle du chef. Gardez
tous ces produits hors de portée des enfants.
• Placez les articles aiguisés de manière à ce qu’ils
n’endommagent pas le joint de la porte.
• Placez les couteaux les poignées vers le haut afin
de réduire les risques de coupures.
• Ne lavez pas d’articles en plastique dans le
lave-vaisselle du chef, à moins qu’ils portent la
mention lavable au lave-vaisselle ou toute mention
équivalente. Lorsque les articles de plastique
ne portent aucune mention, lisez les
recommandations du fabricant.
• Articles divers : Ne lavez pas des articles comme
les filtres à air électroniques, les filtres de
fournaise et les pinceaux dans votre lave-vaisselle
du chef. Ils pourraient endommager le lave-
vaisselle du chef et décolorer ou tacher la cuve.
• Ne touchez pas à l’élément chauffant pendant
ou immédiatement après le lavage.
• Ne faites pas fonctionner votre lave-vaisselle du
chef lorsque l’un de ses panneaux est enlevé.
• Il faut exercer une étroite surveillance lorsque
vous faites fonctionner le lave-vaisselle du chef
en présence d’enfants.
• Placez les articles légers en plastique de façon
qu’ils ne bougent pas ou ne tombent au fond de
l’appareil pendant le lavage. Ils pourraient être
endommagés s’ils entrent en contact avec
l’élément chauffant.
LORSQUE VOUS UTILISEZ VOTRE LAVE-VAISSELLE DU CHEF
VEUILLEZ LIRE ET SUIVRE À LA LETTRE
CES MESURES DE SÉCURITÉ.
CONSERVEZ CES DIRECTIVES
8
Control Panel – ZBD6605
Chef’s Washer
You can locate
your model
number on the
inside upper
tub flange.
Throughout this
manual, features
and appearance
may vary from
your model.
1 2
Control
Settings
1. WASH CYCLES Knob–Use to select the desired wash cycle based on dishware and soil level.
HEAVY DUTY For pans or cookware with dried-on or baked-on soils.
This cycle may not remove some burned-on foods.
NORMAL WASH For loads of everyday cookware with medium soils. NOTE: For heavily soiled
cookware, choose NORMAL WASH plus HIGH TEMP water temperature
option.
LIGHT WASH For lightly soiled cookware.
SPEED WASH For recently used, lightly soiled cookware to be washed in a short time.
Provides a wash with temperatures of up to 125°F (51°C).
RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent
with this cycle.
2. HEAT OPTIONS Knob–Used to select water temperature and drying options.
NORMAL Provides a wash and rinse with water temperatures up to 125°F (51°C) in
LIGHT WASH, 135°F (57°C) in the NORMAL WASH cycle and 155°F (68°C)
in HEAVY DUTY.
HIGH TEMP. Provides a wash and rinse with water temperatures up to 160°F (71°C) in
LIGHT WASH, NORMAL WASH and HEAVY DUTY. Not available for
SPEED WASH, LIGHT WASH or RINSE ONLY cycles.
SANITIZE Provides a sanitizing wash and rinse with water temperatures up to 160°F
(71°C) in LIGHT WASH and 171°F (77°C) in NORMAL WASH and HEAVY
DUTY. Not available for SPEED WASH or RINSE ONLY cycles. At the end
of the cycle, the HEAT OPTIONS light will illuminate to indicate that the
sanitization conditions have been met.
NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.
HEAT DRY When selected, turns the drying heater on for fast drying. The option will
extend the cycle by 30 minutes. When this option is NOT selected, the
fan will turn on to dry your dishes without added heat–energy is saved.
HEAT DRY is not available on RINSE ONLY.
ZBD6605
NSF INTERNATIONAL
Meets NSF Protocol for Performance of Domestic Spray-Type Pots
and Pans Washing Machines (NSF Protocol P180) Requirements for
cleaning and sanitization of cookware.
R
E
S
I
D
E
N
T
I
A
L
9
Operation – ZBD6605
Chef’s Washer
To interrupt/pause a cycle, gently open the door just enough to turn off the wash motor. Do not
fully open the door until the wash action ceases.
CAUTION: Be careful when opening the door; the hot steam that escapes when the door is
opened may cause injuries. Stand back as you open the door and allow the steam
to escape.
ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui
s’échappe lorsque vous ouvrez la porte pendant un programme de lavage peut
causer des brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur
s’échapper de l’appareil.
To restart the wash process, close the door until it locks in place. There may be a time delay of
up to a few minutes because the temperature inside your Chef’s Washer needs to stabilize before
it restarts the wash cycle.
To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.
The Chef’s Washer will start to drain and the cycle indicator lights will flash. At this point a new
wash cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out
after the Chef’s Washer drains completely. If you have selected a new wash cycle, remember to
add more detergent to the detergent compartment if required.
NORMAL
NORMAL
& HEAT
DRY
SANITIZE
(includes
HEAT DRY)
HEAVY DUTY
NORMAL WASH
LIGHT WASH
SPEED WASH
RINSE ONLY
Wash Cycles
✓
✓
✓
✓
✓
✓
✓
✓
✓
—
To start the Chef’s Washer, close the door until it locks in place. To start the last selected cycles,
press the START button. To select a different cycle, turn the knobs to the desired WASH CYCLE
and HEAT OPTIONS and press the START button.
NOTE: Not all heat options are available for all cycles. If a combination that is not available is
selected, the lights will flash when the START button is pressed, and the cycle will not start.
HEAT OPTIONS
HIGH
TEMP &
HEAT DRY
HIGH
TEMP
✓
✓
✓
—
—
✓
✓
✓
—
—
✓
✓
✓
—
—
Start a
wash load
10
Control Panel – ZBD6905
Chef’s Washer
ZBD6905
SENSING Displayed when the dishwasher is monitoring temperature and water level
during fill and drain.
WASHING Displayed during the prewash and main wash periods.
RINSING Displayed during rinse periods.
DRYING Displayed during the dry period (if SMART DRY is selected).
CLEAN Displayed when cycle is complete. Light remains ON until the door is opened.
2. Cycle Selections–The light on the selected pad will illuminate to indicate which cycle has been
selected.
HEAVY DUTY For pans or cookware with dried-on or baked-on soils.
This cycle may not remove some burned-on foods.
NORMAL WASH For loads of everyday cookware with medium soils. NOTE: For heavily soiled
cookware, choose NORMAL WASH plus HIGH water temperature option.
LIGHT WASH For lightly soiled cookware or recently used, lightly soiled cooking
utensils and cookware to be washed in a short time.
RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent with
this cycle.
Control
Settings
1. Cycle Status Indicators–This display tells you what is happening while the Chef’s Washer is in
operation. All of the Cycle Status Indicators will flash on and off if either the door is opened
during a cycle or if the cycle has been paused. Your wash is complete when the CLEAN light
is illuminated.
1 2 543
You can locate
your model
number on the
inside upper
tub flange.
Throughout this
manual, features
and appearance
may vary from
your model.
3. SMART DRY–When selected, sensors detect the presence of rinse aid and the final rinse
temperature. The drying heater and fan are then turned on for the minimum time to achieve
optimum drying results, saving energy over conventional heated dry and time over non-heated
dry. SMART DRY is not available on RINSE ONLY.
4. WATER TEMP–This button provides extra heat options to increase water temperature for
optimum performance.
NORMAL This is the default setting–provides a wash and rinse with water temperatures
up to 125°F (51°C) in the LIGHT WASH, 135°F (57°C) in the NORMAL
WASH cycle and 155°F (68°C) in HEAVY DUTY.
HIGH This water temp selection provides a wash and rinse with water temperatures
up to 160°F (71°C) in LIGHT WASH, NORMAL WASH and HEAVY DUTY.
Use this option for heavily soiled dishes. Cannot be used with RINSE ONLY.
SANI This water temp selection provides a sanitizing wash and rinse with water
temperatures up to 160°F (71°C) in LIGHT WASH and 171°F (77°C) in
NORMAL WASH and HEAVY DUTY. Cannot be used with RINSE ONLY.
At the end of the WASH cycle, the SANI OPTION light will remain illuminated
to indicate that the sanitization conditions have been met.
NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.
5. DELAY START–This option will allow you to delay the start time of any wash cycle except
RINSE ONLY for up to 6 hours.
1. Select the delay start time you want by pressing the DELAY START button. Multiple pressing
will alternate the delay time between 2, 4 or 6 hours and OFF.
2. The last programmed cycle will automatically be selected. A new cycle and options can also
be selected. The DELAY START light/lights will flash to indicate time selected.
3. The flashing Delay Start Indicators show how many hours will elapse before washing begins.
Start a
wash load
To start the Chef’s Washer, close the door until it locks in place. The last used cycle will be displayed.
To begin this cycle, push the START button. To select a different cycle, push the desired Cycle
Selection and Option buttons, and then press the START button.
The door must be closed and latched into place to select a cycle or an option.
To interrupt/pause a cycle, press the selected cycle button. The Status Indicators will flash.
CAUTION: Be careful when opening the door; the hot steam that escapes when the door is
opened may cause injuries. Stand back as you open the door and allow the steam
to escape.
ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui s’échappe
lorsque vous ouvrez la porte pendant un programme de lavage peut causer des
brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur s’échapper
de l’appareil.
To restart the wash process, close the door until it locks in place. Re-press the cycle button. There
may be a time delay of up to a few minutes, because the temperature inside the Chef’s Washer
needs to stabilize before it restarts the wash cycle. During this time the SENSING light will be on.
To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.
The Chef’s Washer will then drain and the cycle indicator lights will flash. At this point a new wash
cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out after the
Chef’s Washer drains. If you have selected a new wash cycle, remember to add more detergent to
the detergent compartment if required.
11
Control Panel/Operation – ZBD6905
Chef’s Washer
NSF INTERNATIONAL
Meets NSF Protocol for Performance of Domestic Spray-Type Pots
and Pans Washing Machines (NSF Protocol P180) Requirements for
cleaning and sanitization of cookware.
R
E
S
I
D
E
N
T
I
A
L
1. Cycle Selections–The light on the selected pad will illuminate to indicate which cycle has been
selected.
HEAVY DUTY For pans or cookware with dried-on or baked-on soils.
This cycle may not remove some burned-on foods.
NORMAL WASH For loads of everyday cookware with medium soils. NOTE: For heavily soiled
cookware, choose NORMAL WASH plus HIGH water temperature option.
LIGHT WASH For lightly soiled cookware or recently used, lightly soiled cooking utensils
and cookware to be washed in a short time.
RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent with
this cycle.
2. WATER TEMP–This button provides extra heat options to increase water temperature for
optimum performance.
NORMAL This is the default setting–provides a wash and rinse with water temperatures
up to 125°F (51°C) in LIGHT WASH, 135°F (57°C) in the NORMAL WASH
cycle and 155°F (68°C) in HEAVY DUTY.
HI TEMP This water temp selection provides a wash and rinse with water temperatures
up to 160°F (71°C) in LIGHT WASH, NORMAL WASH and HEAVY DUTY.
SANITIZE This water temp selection provides a sanitizing wash and rinse with water
temperatures up to 160°F (71°C) in LIGHT WASH and 171°F (77°C) in NORMAL
WASH and HEAVY DUTY. This selection cannot be used with RINSE ONLY.
At the end of the wash cycle, the SANITIZE OPTION light will remain
illuminated to indicate that the sanitization conditions have been met.
NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.
3. SMART DRY–When selected, sensors detect the presence of rinse aid and the final rinse
temperature. The drying heater and fan are then turned on for the minimum time to achieve
optimum drying results, saving energy over conventional heated dry and time over non-heated
dry. SMART DRY is not available on RINSE ONLY.
12
Control Panel – ZBD7005 & ZBD7105
Chef’s Washer
ZBD7005 & ZBD7105
Control
Settings
1 3 42
You can locate
your model
number on the
inside upper
tub flange.
Throughout this
manual, features
and appearance
may vary from
your model.
NSF INTERNATIONAL
Meets NSF Protocol for Performance of Domestic Spray-Type Pots
and Pans Washing Machines (NSF Protocol P180) Requirements for
cleaning and sanitization of cookware.
R
E
S
I
D
E
N
T
I
A
L
To start the Chef’s Washer, open the Chef’s Washer door so that the top-of-door controls are
visible. The last used cycle will be displayed. To begin this cycle, press the START button. To select
a different cycle, press the desired Cycle Selection and Option buttons, and then press the START
button. After the door is closed and latched, the selected cycle will begin.
To interrupt/pause a cycle, gently open the door just enough to turn off the wash motor. Do not
fully open the door until the wash action ceases.
WARNING: Do not fully open door while the Chef’s Washer is in operation. Quickly opening
the door while the Chef’s Washer is operating could result in serious scalding.
Be careful when opening the door; the hot steam that escapes when the door
is opened may cause injuries. Stand back as you open the door and allow the
steam to escape.
AVERTISSEMENT : N’ouvrez pas complètement la porte lorsque la laveuse fonctionne. Une
ouverture rapide de la porte lorsque l’appareil est en fonctionnement
peut entraîner de sérieuses brûlures. Faites attention lorsque vous ouvrez
la porte; la vapeur brûlante qui s’échappe lors de l’ouverture de la porte
peut causer des blessures. Tenez vous en arrière lorsque vous ouvrez la
porte afin de permettre à la vapeur de s’échapper.
To restart the wash process, close the door until it locks in place. There may be a time delay of
up to a few minutes because the temperature inside the Chef’s Washer needs to stabilize before
it restarts the wash cycle.
To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.
The Chef’s Washer will start to drain and the cycle indicator lights will flash. At this point a new
wash cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out
after the Chef’s Washer drains completely. If you have selected a new wash cycle, remember to
add more detergent to the detergent compartment if required.
13
Start a
Wash Load
Control Panel/Operation – ZBD7005 & ZBD7105
Chef’s Washer
Control
Settings
4. DELAY START–This option will allow you to delay the start time of any wash cycle except
RINSE ONLY for up to 6 hours.
• Select the delay start time you want by pressing the DELAY START button. Multiple pressing
will alternate the delay time between 2, 4 or 6 hours and OFF.
Features – ZBD6605, ZBD6905, ZBD7005, ZBD7105
Chef’s Washer
Auto
Memory
Your Chef’s Washer has the ability to remember what options you like with NORMAL WASH and
HEAVY DUTY wash cycle. This means that if you select NORMAL WASH, your Chef’s Washer will
automatically select the options that you selected last time you washed with the NORMAL WASH cycle.
You can change the options that have been remembered with a particular wash cycle if you desire.
Child
Lockout
Mode
(on some
models)
To reduce the possibility of children starting the Chef’s Washer when unattended, a child lockout
feature can be enabled. Once enabled, each button must be pressed and held for two seconds until
you hear a BEEP, before the Chef’s Washer will respond. While in this mode, the SENSING and
CLEAN light will illuminate while the button is pressed.
This feature can be enabled by pressing both the START/CANCEL and HEAVY DUTY buttons
together and holding both for two seconds. You will hear three BEEPS when the child lockout
is enabled.
The child lockout can be cancelled by pressing the START/CANCEL and HEAVY DUTY together
and holding both pressed for two seconds until a single BEEP is heard.
NOTE: Child lockout overrides tone silencing.
Tone
Silencing
(on some
models)
You can prevent the beep from sounding when selecting control settings.
1. Press the START/CANCEL and NORMAL WASH buttons together prior to selecting settings.
2. To have sound again, simply press the START/CANCEL and NORMAL WASH buttons
together again.
14
Detergent
Usage
Guide
(Powder or
Liquid)
SOFT WATER MEDIUM WATER HARD WATER
0–3 grains 3–7 grains 7–12 grains*
CYCLES Main Cup Auxiliary Cup Main Cup Auxiliary Cup Main Cup Auxiliary Cup
HEAVY DUTY Full None Full Full Full Full
NORMAL WASH
1
⁄2 Full None Full None Full Full
LIGHT WASH
1
⁄2 Full None Full None Full Full
SPEED WASH
1
⁄2 Full None Full Full Full Full
RINSE ONLY Use no detergent Use no detergent Use no detergent
*12 grains and up is extremely hard water. A water softener
is recommended. Without it, lime can build up in the water
valve. The water valve may stick and flooding could occur.
NOTE: The above chart is a general guide. Detergent
amounts should be adjusted depending on the amount
and type of soil until satisfactory results are achieved.
Cycle Chart
APPROXIMATE CYCLE TIME
With 120°F Water
TEMPERATURE (°F) (excluding drying time)
Sani
(on some
CYCLES Normal High models) Normal High Sani
HEAVY DUTY 155 160 171 7.4 70 77 84
NORMAL WASH 135 145–160 160–171 5.0–11.2 50 94 80
LIGHT WASH 125 135–160 160 5.0 30 50 63
SPEED WASH 115–125 — — 3.8 23 — —
RINSE ONLY — — — 1.2 11 — —
WATER USAGE
(Gallons)
Use only detergent specifically made for use in
dishwashers. Keep your powdered detergent
fresh
and dry. Don’t put powder detergent into
the
dispenser until you’re ready to wash dishes.
The amount of detergent to use depends on
whether your water is hard or soft. With hard
water, you need extra detergent. With soft
water, you need less detergent.
Protect your dishes and Chef’s Washer by
contacting your water department and asking
how hard your water is. Twelve or more
grains
is extremely hard water. A water softener is
recommended.
Without it, lime can build up
in the water valve, which could stick while open
and cause flooding. Too much detergent with
soft water can cause a permanent cloudiness
of glassware, called etching.
To open the detergent compartment, push the
lever latch inward.
When using automatic dishwashing detergent
tabs, place one tab in the main cup and close.
Be sure the Cycle Status Indicators (on some
models) are not lit before adding detergent.
Otherwise, the detergent cup will not close and
latch properly. Add detergent, then close the
main cup.
NOTE: To open detergent cup after it has been
closed, push the lever latch inward.
Lever
Main compartment
15
Using the Chef’s Washer
Chef’s Washer
Detergents
Water
Temperature
The entering water must be at least 120°F
(49°C) and
not more than 150°F (66°C), for
effective cleaning and to prevent dish damage.
Check the water temperature with a candy or
meat thermometer. Turn on the hot water
faucet nearest the Chef’s Washer, place
the thermometer in a glass and let the water
run continuously into the glass until the
temperature stops rising.
Use a
Rinse
Agent
A rinse agent improves dry performance,
reduces spots and prevents new film buildup
on your dishes, glasses, flatware, cookware
and plastic.
Fill the rinse agent chamber by rotating the
round cap counterclockwise and remove. Fill
chamber to maximum level. Replace and lock
the cap into place.
To check if rinse agent is needed: a solid black
indicator indicates sufficient rinse agent; a clear
indicator indicates a low level and requires
adding more rinse agent.
• A full dispenser should last about one month.
• If rinse agent spills, wipe it up immediately.
It can keep your detergent from working.
•
If after washing you notice cloudy spots,
streaks or water marks on the glassware, and
the rinse agent dispenser is not empty, it may
be necessary to increase the dispenser settings.
To do so, remove the cap and using a butter
knife, rotate the indicator arrow to a higher
number. Replace the cap when done.
•
If glasses appear smeared or there is foam
present on the bottom of the glasses or the
bottom of the machine, select a lower dosage
number.
•
For softened water, reduce dispenser setting.
Light level indicator
Adjust to higher or lower number
Auxiliary
compartment
16
Loading the Racks
Chef’s Washer
Upper Rack
The upper rack is for small bowls and pans. This is
also a secure place for dishwasher-safe plastics.
Because bowls and casserole dishes come in various
sizes, after loading, slowly push in the rack to make sure
they will clear the top of the Chef’s Washer.
The upper rack is also good for all kinds of oddly-
shaped utensils. Saucepans, mixing bowls and other
items should be placed face down.
Make sure small plastic items are secure so they can’t
fall onto the heating element.
Upper
Wash
Tower
Take care not to obstruct the rotation of the
spray arm under the upper rack or cover the
water collector in the center of the upper rack.
Squeeze
Re-adjust
upper rack
Adjusting
Upper Rack
Height
The upper rack can be raised or lowered to
provide extra room for different sized items.
Empty the upper rack. Remove the rail pegs
in the front of the rack runners by squeezing
and lifting the top of the peg, then slide the
rack out.
Re-insert the rack in the chosen position and
replace the pegs. Check that the spray arm is
free to rotate.
Lift peg from
rack runner
This Chef’s Washer is designed for dishwasher-safe gourmet cookware.
17
Lower Rack
When loading the lower rack, do not load tall platters
or trays in the front left corner. They may prevent
detergent cup from opening during the wash cycle.
The lower rack is best used for large trays, saucepans
and cookware. There is 15″ clearance for tall items.
Large items such as broiler pans and racks should go
along the sides. Load platters, pots and bowls along
the sides, in corners or in the back. The soiled side
of items should face down or the center of the rack.
Fold-down tray dividers provide flexibility for extra
large and hard-to-fit items.
The tray dividers may be left in the up position or
folded down to customize the lower rack.
Silverware
and Utensil
Basket
Put flatware in the removable basket with fork and knife handles up to protect your hands. Place
spoons in the basket with handles down. Mix knives, forks and spoons so they don’t nest together.
Distribute evenly. Small plastic items, such as measuring spoons and lids from small containers,
should go in the bottom of the silverware basket with silverware on top.
Flip-down covers can be lowered to secure lightweight items from the effects of the vigorous wash
action. The slots in the covers can be used to separate silverware.
Don’t let any item extend through bottom
Tray Divider
18
Care and Cleaning
Chef’s Washer
Exterior
To clean the control panel, use a lightly dampened cloth, then dry thoroughly. To clean the
exterior painted panels, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the Chef’s Washer.
Use stainless steel cleaner on stainless steel panel. You can order
Stainless Steel Magic # WX10X15
through GE Parts in the USA, by calling 800.626.2002. In Canada, call 1.888.880.3030.
Protect
Against
Freezing
If your Chef’s Washer is left in an unheated place during the winter, ask a service technician to:
1. Cut off electrical power to the Chef’s Washer. Remove fuses or trip circuit breaker.
2. Turn off the water supply and disconnect the water inlet line from the water valve.
3. Drain water from the water inlet line and water valve. (Use a pan to catch the water.)
4. Reconnect the water inlet line to the water valve.
5. Remove the filters from the tub bottom and use a sponge to soak up water.
The Air
Gap
An air gap protects your Chef’s Washer against
water backing up into it if a drain clogs. The air
gap is not a part of the Chef’s Washer. It is not
covered by your warranty. Not all plumbing
codes require air gaps, so you may not have one.
The air gap is easy to clean.
1. Turn off the Chef’s Washer and lift off the
chrome cover.
2. Unscrew the plastic cap and clean with
a toothpick.
Interior
The stainless steel tub can be cleaned with Stainless Steel Magic or a similar product using
a clean, soft cloth.
Use stainless steel cleaner on stainless steel panel. You can order
Stainless Steel Magic # WX10X15
through GE Parts in the USA, by calling 800.626.2002. In Canada, call 1.888.880.3030.
Wipe the rubber door seals occasionally, including the seal at the bottom of the door.
Check the air gap any time your Chef’s Washer
isn’t draining well.
Two types
of air gaps
19
Removing
and Cleaning
the Spray
Arms and
Glass Trap
Periodically, remove and clean the spray arms
to make sure that none of the nozzles have
become blocked.
To remove the lower spray arm, grasp the
center of the spray arm and pull upward; it will
unclip. When replacing, make sure the spray
arm is fully seated and spins.
The plastic cone on the underside of the
spray arm can be detached by unscrewing it
counterclockwise.
To remove the upper spray arm, carefully
unscrew the spray arm from the plastic tower.
To achieve this, hold the inner tower steady
and unscrew the spray arm clockwise. To
replace the spray arm, carefully screw the spray
arm counterclockwise onto the inner tower.
To clean the upper and lower spray arms,
rinse them under running water and make
sure spray nozzles are clear.
The glass trap is located in the stainless steel
filter at the base of your Chef’s Washer. The
glass trap is used to collect larger food items
and other foreign objects, which may be too
big to pass through the drain pump. For best
wash performance, check the glass trap
occasionally.
To remove the glass trap, twist counterclockwise,
rotate the glass trap
and lift. To clean the glass
trap, empty and rinse thoroughly. To replace,
reverse these steps, making sure the glass trap
locks into place.
Pull up to remove
Rotate counterclockwise and
lift to remove glass trap
Rotate counterclockwise
to remove cone
20
Care and Cleaning
Chef’s Washer
The Wash
Filters
In addition to the glass trap, your Chef’s
Washer has three fine filters–
• a two piece round perforated stainless steel
filter located in the base of the Chef’s Washer.
• a finer micro-mesh filter located under the
stainless steel filter.
• a super fine filter located below the lower
spray arm.
Remove the stainless steel filter by first twisting
and removing the glass trap. Lift out the
stainless steel filter.
Attached to the underside of this filter is the
micro-mesh filter. To remove the micro-mesh
filter, squeeze the two clips above the stainless
steel filter to release the micro-mesh.
To remove the super fine filter, remove the
lower spray arm. Grasp the super fine filter
around the outer edges. Remove by pulling
upward; it will unclip. Unscrew the tower
counterclockwise. The right half of the stainless
steel filter can now be removed.
To clean filters, place under running water
and gently brush with a soft bristled brush.
Be careful not to deform filters while cleaning,
as
this may prevent them from being properly
re-installed.
The super fine filter is self-cleaning; there is
no need to clean it. This filter need only be
removed if you want to remove the right half
of the stainless steel filter.
Replace your filters in the reverse order,
starting with the right half of the stainless
steel filter. Then screw in the tower. Replace
the super fine filter over the tower by pressing
firmly on the outer edge until it clips into
place and reposition the lower spray arm.
Reconnect the micro-mesh filter to the left
half of the stainless steel filter prior to
replacing it back into the Chef’s Washer. Then
replace the glass trap. Ensure that all filters
are replaced correctly for best results.
Grip filter and lift
to remove
Perforated stainless
steel filter
Micro-mesh filter
Squeeze clips to remove
micro-mesh filter
Pull super fine
filter up to remove
Lift stainless steel
filter to remove
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
GE ZBD6905GSS Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur
dans d''autres langues
- English: GE ZBD6905GSS User manual
