Monogram ZBD7105 Manuel utilisateur

Marque: Monogram

Modèle: ZBD7105

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Owner’s

Manual

Chef’s Washer

ZBD6605

ZBD6905

ZBD7005

ZBD7105

2
Consumer Information
Chef’s Washer
Your new Monogram Chef’s Washer makes an eloquent statement of style, convenience and
kitchen planning flexibility. Whether you chose it for its purity of design, practical features or
assiduous attention to detail–or for all of these reasons–you’ll find that your Monogram Chef’s
Washer’s superior blend of form and function will delight you for years to come.
The information on the following pages will help you operate and maintain your Chef’s 
Washer properly.
If you have any other questions, visit our Website at: monogram.com
Introduction
Contents
Appliance Registration  . . . . . . . . . . . .3, 31, 32
Care and Cleaning  . . . . . . . . . . . . . . . . .18–21
Consumer Services  . . . . . . . . . . . . . . . . . .3, 26
Model and Serial Number Location  . . . . . . .3
Operating Instructions  . . . . . . . . . . . . . . .8–17
Control Panel and Settings for
ZBD6605  . . . . . . . . . . . . . . . . . . . . . . . .8, 9
Control Panel and Settings for
ZBD6905  . . . . . . . . . . . . . . . . . . . . . .10, 11
Control Panel and settings for
ZBD7005 and ZBD7105  . . . . . . . . . . .12, 13
Tone Silencing  . . . . . . . . . . . . . . . . . . . . .14
Clean Sensor  . . . . . . . . . . . . . . . . . . . . . .14
Auto Memory  . . . . . . . . . . . . . . . . . . . . . .14
Child Lockout Mode  . . . . . . . . . . . . . . . .14
Water Temperature  . . . . . . . . . . . . . . . . .15
Rinse Agent  . . . . . . . . . . . . . . . . . . . . . . .15
Detergents  . . . . . . . . . . . . . . . . . . . . . . . .15
Dishwasher Racks  . . . . . . . . . . . . . . . .16, 17
Problem Solver  . . . . . . . . . . . . . . . . . . . .22–25
Safety Instructions  . . . . . . . . . . . . . . . . . . .4–7
USA Warranty . . . . . . . . . . . . . . . . . . . . . . . .27
Canada Warranty  . . . . . . . . . . . . . . . . . . . . .28

Consumer Information

Chef’s Washer

Before

using

your

Chef’s

Washer

Read this manual carefully. It is intended

to help you operate and maintain your new

Chef’s Washer properly.

Keep it handy for answers to your questions.

If you don’t understand something or need

more help, there is a list of toll-free consumer

service numbers included in the back section

of this manual.

Visit our Website at: monogram.com

Write

down the

model &

serial

numbers

You can find the model and serial numbers

at the inside upper left tub flange.

Before sending in this card, please write these

numbers here:

Model Number

Serial Number

Use these numbers in any correspondence or

service calls concerning your Chef’s Washer.

If you received

a damaged

Chef’s Washer

Immediately contact the dealer (or builder)

that sold you the Chef’s Washer.

Save time

& money

Before you request service, check the Problem

Solver in the back of this manual.

It lists causes of minor operating problems that

you can correct yourself.

If you

need service

To obtain service, see the Consumer Services

page in the back of this manual.

We’re proud of our service and want you to be

pleased. If for some reason you are not happy

with the service you receive, here are steps to

follow for further help.

For customers in the USA:

FIRST, contact the people who serviced your

appliance. Explain why you are not pleased.

In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the

details–including your phone number–to:

Manager, Customer Relations

GE Appliances

Appliance Park

Louisville, KY 40225

For customers in Canada:

FIRST, contact the people who serviced your

appliance. Explain why you are not pleased.

In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the

details–including your phone number–to:

Manager, Consumer Relations

Camco Inc.

1 Factory Lane, Suite 310

Moncton, N.B. E1C 9M3

A junked or abandoned Chef’s Washer is

dangerous…even if it will sit for “just a

few days.” If you are getting rid of your old

Chef’s Washer, please follow the instructions

below to help prevent accidents.

Before You Throw Away Your Old Chef’s Washer:

• Take off the door of the washing

compartment or remove the door latch

keeper (as shown).

IMPORTANT SAFETY INSTRUCTIONS

MESURES DE SÉCURITÉ IMPORTANTES

WARNING!

For your safety, the information in this manual

must be followed to minimize the risk of fire,

explosion, electric shock, or to prevent property

damage, personal injury or loss of life.

• Do not tamper with controls.

• Do not abuse, sit on, or stand on the door or

dish rack of the Chef’s Washer.

• Do not discard a Chef’s Washer without first

removing the door or removing the door latch.

• Do not store or use combustible materials,

gasoline or other flammable vapors and

liquids

in the vicinity of this or any other appliance.

• Do not allow children to play inside, on or with

this appliance or any discarded appliance.

• Do not allow children to play around the Chef’s

Washer when opening and closing the door due

to possibility of small fingers being pinched in

the door.

AVERTISSEMENT

Pour votre sécurité, veuillez suivre à la lettre les

directives données dans le présent manuel afin

de réduire les risques d’incendie, d’explosion ou

de chocs électriques, et prévenir les dommages

matériels et les blessures graves ou mortelles.

• Ne modifiez pas le fonctionnement des

commandes.

• Ne montez pas ou ne vous assoyez pas sur la

porte ou les paniers du lave-vaisselle du chef,

et ne les utilisez pas de façon abusive.

• Ne jetez pas un lave-vaisselle du chef sans

en avoir d’abord enlevé la porte ou enlevez

le verrou de la porte.

• N’entreposez pas et n’utilisez pas d’essence,

de vapeurs ou de liquides inflammables à

proximité de cet appareil ou de tout autre

électroménager.

• Ne laissez pas les enfants jouer avec le lave-

vaisselle du chef ni monter dessus. Ne les

laissez pas s’introduire à l’intérieur de cet

appareil ou d’un vieil appareil qui ne sert plus.

•

Ne permettez jamais à des enfants de jouer

à proximité d’un lave-vaisselle du chef quand

vous ouvrez ou fermez la porte. Ils peuvent

se coincer les doigts dans la porte.

BONNE DISPOSITION DU LAVE-VAISSELLE DU CHEF

Le lave-vaisselle du chef abandonné ou jeté est

dangereux...même s’il est abandonné «juste

pendant quelques jours». Si vous jetez votre

vieux lave-vaisselle du chef, veuillez suivre les

instructions suivantes pour prévenir tout

accident.

Avant de jeter votre vieux lave-vaisselle du chef :

• Enlevez la porte du compartiment de lavage

ou enlevez le réceptacle à verrou (comme

l’indique l’illustration).

AVERTISSEMENT! RISQUE D’ENFANT MIS AU PIÈGE

Réceptacle

à verrou

PROPER DISPOSAL OF THE CHEF’S WASHER

WARNING! RISK OF CHILD ENTRAPMENT

Door latch

keeper

WATER HEATER SAFETY

Under certain conditions hydrogen gas may be

produced in a water heater that has not been

used for two weeks or more. HYDROGEN

GAS IS EXPLOSIVE.

If the hot water has not been used for two

weeks or more, prevent the possibility of

damage or injury by turning on all hot water

faucets and allowing them to run for several

minutes. Do this before using any electrical

appliance which is connected to the hot water

system. This simple procedure will allow any

built-up hydrogen gas to escape. Since the gas

is flammable, do not smoke or use an open

flame or appliance during this process.

SÉCURITÉ DU CHAUFFE-EAU

Dans certaines conditions, il peut se former de

l’hydrogène à l’intérieur d’un chauffe-eau qui

n’a pas servi pendant deux semaines ou plus.

L’HYDROGÈNE EST UN GAZ EXPLOSIF.

Pour réduire les risques de dommages ou de

blessures lorsque l’eau chaude n’a pas été

utilisée depuis deux semaines ou plus, ouvrez

tous les robinets d’eau chaude et laissez l’eau

couler pendant plusieurs minutes avant

d’utiliser un appareil électrique raccordé au

système d’eau chaude. Vous éliminerez ainsi

l’hydrogène qui pourrait s’y être accumulé.

Puisqu’il s’agit d’un gaz inflammable, ne fumez

pas ou n’utilisez pas une flamme nue au cours

de ce processus.

IMPORTANT SAFETY INSTRUCTIONS

MESURES DE SÉCURITÉ IMPORTANTES

PROPER INSTALLATION AND MAINTENANCE

This Chef’s Washer must be properly installed

and located in accordance with the Installation

Instructions before it is used. If you did not

receive an Installation Instructions sheet with

your Chef’s Washer, you can receive one by

visiting our Website at monogram.com

• Connect to a grounded metal, permanent

wiring system; or run an equipment-

grounding conductor with the circuit

conductors and connect to the equipment-

grounding terminal or lead of the appliance.

• Improper connection of the equipment-

grounding conductor can result in a risk of

electric shock. Check with a qualified

electrician or service representative if you are

in doubt whether the appliance is properly

grounded.

• Dispose of discarded appliances and shipping

or packing material properly.

• Do not attempt to repair or replace any part

of your Chef’s Washer unless it is specifically

recommended in this manual. All other

servicing should be referred to a qualified

technician.

• To minimize the possibility of electric shock,

disconnect this appliance from the power

supply before attempting any maintenance.

NOTE: Turning the Chef’s Washer off does

not disconnect the appliance from the power

supply. We recommend having a qualified

technician service your appliance.

INSTALLATION ET ENTRETIEN APPROPRIÉS

Avant de l’utiliser, vous devez installer

correctement ce lave-vaisselle du chef

conformément aux directives d’installation

fournies. Si vous n’avez pas reçu une feuille

de directives d’installation avec votre lave-

vaisselle du chef, vous pouvez en obtenir un

exemplaire par visiter notre site Web à l’adress

monogram.com.

• Cet appareil doit être relié à un système de

câblage électrique permanent, mis à la terre.

Sinon, un fil de mise à la terre pour

appareillage doit être installé et raccordé à la

borne ou au fil de mise à la terre de l’appareil.

• Un raccordement non approprié du fil

de mise à la terre pour appareillage peut

présenter des risques de chocs électriques.

Si vous doutez de la qualité de la mise à la

terre de votre électroménager, consultez un

représentant du Service après-vente ou un

électricien qualifié.

• Jetez de la façon appropriée les vieux

électroménagers, ainsi que le matériel

d’emballage et d’expédition.

• Ne tentez pas de réparer ou de remplacer

toute pièce de votre lave-vaisselle du chef,

à moins que cela ne soit spécifiquement

recommandé dans le présent manuel. Confiez

toutes les autres réparations à un réparateur

qualifié.

• Afin de réduire les risques de chocs électriques,

débranchez toujours l’appareil avant de le

réparer. REMARQUE : Lorsque vous mettez

la commande du lave-vaisselle du chef à OFF

(arrêt), le courant qui alimente l’appareil n’est

pas coupé. Nous vous recommandons de

confier la réparation de votre appareil à un

réparateur qualifié.

Use this appliance only for its intended

purpose as described in this Owner’s Manual.

CAUTION: Contents washed

in the Sanitization cycle may be hot to the

touch. Use care before unloading.

• Use only powder, tabs or liquid detergents

or wetting agents recommended for use in

a Chef’s Washer and keep them out of the

reach of children.

• Locate sharp items so that they are not

likely to damage the door seal.

• Load sharp knives with the handles up

to reduce the risk of cut-type injuries.

• Do not wash cookware unless marked

dishwasher safe or the equivalent. For

plastic items not so marked, check the

manufacturer’s recommendations.

• Non-Dishware Items: Do not wash items such

as electronic air cleaner filters, furnace filters

and paint brushes in your Chef’s Washer.

Damage to Chef’s Washer and discoloration

or staining of Chef’s Washer may result.

• Do not touch the heating element during

or immediately after use.

• Do not operate your Chef’s Washer unless

all enclosure panels are properly in place.

• Close supervision is necessary if this

appliance is used by or near children.

• Load light plastic items so they will not

become dislodged and drop to the bottom

of the Chef’s Washer–they might come into

contact with the heating element and

be damaged.

WHEN USING YOUR CHEF’S WASHER

READ AND FOLLOW THIS SAFETY

INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

N’utilisez ce lave-vaisselle du chef que pour

l’usage auquel il est destiné, comme expliqué

dans le présent Manuel d’utilisation.

MISE EN GARDE : Les

matériaux lavés selon le cycle Sanitization

peuvent être chauds. Faites attention quand

vous videz votre machine.

• N’utilisez que des détergents liquides, en

poudre ou en pastilles et les produits de rinçage

recommandés pour lave-vaisselle du chef. Gardez

tous ces produits hors de portée des enfants.

• Placez les articles aiguisés de manière à ce qu’ils

n’endommagent pas le joint de la porte.

• Placez les couteaux les poignées vers le haut afin

de réduire les risques de coupures.

• Ne lavez pas d’articles en plastique dans le

lave-vaisselle du chef, à moins qu’ils portent la

mention lavable au lave-vaisselle ou toute mention

équivalente. Lorsque les articles de plastique

ne portent aucune mention, lisez les

recommandations du fabricant.

• Articles divers : Ne lavez pas des articles comme

les filtres à air électroniques, les filtres de

fournaise et les pinceaux dans votre lave-vaisselle

du chef. Ils pourraient endommager le lave-

vaisselle du chef et décolorer ou tacher la cuve.

• Ne touchez pas à l’élément chauffant pendant

ou immédiatement après le lavage.

• Ne faites pas fonctionner votre lave-vaisselle du

chef lorsque l’un de ses panneaux est enlevé.

• Il faut exercer une étroite surveillance lorsque

vous faites fonctionner le lave-vaisselle du chef

en présence d’enfants.

• Placez les articles légers en plastique de façon

qu’ils ne bougent pas ou ne tombent au fond de

l’appareil pendant le lavage. Ils pourraient être

endommagés s’ils entrent en contact avec

l’élément chauffant.

LORSQUE VOUS UTILISEZ VOTRE LAVE-VAISSELLE DU CHEF

VEUILLEZ LIRE ET SUIVRE À LA LETTRE

CES MESURES DE SÉCURITÉ.

CONSERVEZ CES DIRECTIVES

Control Panel – ZBD6605

Chef’s Washer

You can locate

your model

number on the

inside upper

tub flange.

Throughout this

manual, features

and appearance

may vary from

your model.

1 2

Control

Settings

1. WASH CYCLES Knob–Use to select the desired wash cycle based on dishware and soil level.

HEAVY DUTY For pans or cookware with dried-on or baked-on soils.

This cycle may not remove some burned-on foods.

NORMAL WASH For loads of everyday cookware with medium soils. NOTE: For heavily soiled

cookware, choose NORMAL WASH plus HIGH TEMP water temperature

option.

LIGHT WASH For lightly soiled cookware.

SPEED WASH For recently used, lightly soiled cookware to be washed in a short time.

Provides a wash with temperatures of up to 125°F (51°C).

RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent

with this cycle.

2. HEAT OPTIONS Knob–Used to select water temperature and drying options.

NORMAL Provides a wash and rinse with water temperatures up to 125°F (51°C) in

LIGHT WASH, 135°F (57°C) in the NORMAL WASH cycle and 155°F (68°C)

in HEAVY DUTY.

HIGH TEMP. Provides a wash and rinse with water temperatures up to 160°F (71°C) in

LIGHT WASH, NORMAL WASH and HEAVY DUTY. Not available for

SPEED WASH, LIGHT WASH or RINSE ONLY cycles.

SANITIZE Provides a sanitizing wash and rinse with water temperatures up to 160°F

(71°C) in LIGHT WASH and 171°F (77°C) in NORMAL WASH and HEAVY

DUTY. Not available for SPEED WASH or RINSE ONLY cycles. At the end

of the cycle, the HEAT OPTIONS light will illuminate to indicate that the

sanitization conditions have been met.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

HEAT DRY When selected, turns the drying heater on for fast drying. The option will

extend the cycle by 30 minutes. When this option is NOT selected, the

fan will turn on to dry your dishes without added heat–energy is saved.

HEAT DRY is not available on RINSE ONLY.

ZBD6605

NSF INTERNATIONAL

Meets NSF Protocol for Performance of Domestic Spray-Type Pots

and Pans Washing Machines (NSF Protocol P180) Requirements for

cleaning and sanitization of cookware.

Operation – ZBD6605

Chef’s Washer

To interrupt/pause a cycle, gently open the door just enough to turn off the wash motor. Do not

fully open the door until the wash action ceases.

CAUTION: Be careful when opening the door; the hot steam that escapes when the door is

opened may cause injuries. Stand back as you open the door and allow the steam

to escape.

ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui

s’échappe lorsque vous ouvrez la porte pendant un programme de lavage peut

causer des brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur

s’échapper de l’appareil.

To restart the wash process, close the door until it locks in place. There may be a time delay of

up to a few minutes because the temperature inside your Chef’s Washer needs to stabilize before

it restarts the wash cycle.

To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.

The Chef’s Washer will start to drain and the cycle indicator lights will flash. At this point a new

wash cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out

after the Chef’s Washer drains completely. If you have selected a new wash cycle, remember to

add more detergent to the detergent compartment if required.

NORMAL

& HEAT

DRY

SANITIZE

(includes

HEAT DRY)

HEAVY DUTY

NORMAL WASH

LIGHT WASH

SPEED WASH

RINSE ONLY

Wash Cycles

✓

—

To start the Chef’s Washer, close the door until it locks in place. To start the last selected cycles,

press the START button. To select a different cycle, turn the knobs to the desired WASH CYCLE

and HEAT OPTIONS and press the START button.

NOTE: Not all heat options are available for all cycles. If a combination that is not available is

selected, the lights will flash when the START button is pressed, and the cycle will not start.

HEAT OPTIONS

HIGH

TEMP &

HEAT DRY

HIGH

TEMP

✓

—

✓

—

✓

—

Start a

wash load

Control Panel – ZBD6905

Chef’s Washer

ZBD6905

SENSING Displayed when the dishwasher is monitoring temperature and water level

during fill and drain.

WASHING Displayed during the prewash and main wash periods.

RINSING Displayed during rinse periods.

DRYING Displayed during the dry period (if SMART DRY is selected).

CLEAN Displayed when cycle is complete. Light remains ON until the door is opened.

2. Cycle Selections–The light on the selected pad will illuminate to indicate which cycle has been

selected.

HEAVY DUTY For pans or cookware with dried-on or baked-on soils.

This cycle may not remove some burned-on foods.

NORMAL WASH For loads of everyday cookware with medium soils. NOTE: For heavily soiled

cookware, choose NORMAL WASH plus HIGH water temperature option.

LIGHT WASH For lightly soiled cookware or recently used, lightly soiled cooking

utensils and cookware to be washed in a short time.

RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent with

this cycle.

Control

Settings

1. Cycle Status Indicators–This display tells you what is happening while the Chef’s Washer is in

operation. All of the Cycle Status Indicators will flash on and off if either the door is opened

during a cycle or if the cycle has been paused. Your wash is complete when the CLEAN light

is illuminated.

1 2 543

You can locate

your model

number on the

inside upper

tub flange.

Throughout this

manual, features

and appearance

may vary from

your model.

3. SMART DRY–When selected, sensors detect the presence of rinse aid and the final rinse

temperature. The drying heater and fan are then turned on for the minimum time to achieve

optimum drying results, saving energy over conventional heated dry and time over non-heated

dry. SMART DRY is not available on RINSE ONLY.

4. WATER TEMP–This button provides extra heat options to increase water temperature for

optimum performance.

NORMAL This is the default setting–provides a wash and rinse with water temperatures

up to 125°F (51°C) in the LIGHT WASH, 135°F (57°C) in the NORMAL

WASH cycle and 155°F (68°C) in HEAVY DUTY.

HIGH This water temp selection provides a wash and rinse with water temperatures

up to 160°F (71°C) in LIGHT WASH, NORMAL WASH and HEAVY DUTY.

Use this option for heavily soiled dishes. Cannot be used with RINSE ONLY.

SANI This water temp selection provides a sanitizing wash and rinse with water

temperatures up to 160°F (71°C) in LIGHT WASH and 171°F (77°C) in

NORMAL WASH and HEAVY DUTY. Cannot be used with RINSE ONLY.

At the end of the WASH cycle, the SANI OPTION light will remain illuminated

to indicate that the sanitization conditions have been met.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

5. DELAY START–This option will allow you to delay the start time of any wash cycle except

RINSE ONLY for up to 6 hours.

1. Select the delay start time you want by pressing the DELAY START button. Multiple pressing

will alternate the delay time between 2, 4 or 6 hours and OFF.

2. The last programmed cycle will automatically be selected. A new cycle and options can also

be selected. The DELAY START light/lights will flash to indicate time selected.

3. The flashing Delay Start Indicators show how many hours will elapse before washing begins.

Start a

wash load

To start the Chef’s Washer, close the door until it locks in place. The last used cycle will be displayed.

To begin this cycle, push the START button. To select a different cycle, push the desired Cycle

Selection and Option buttons, and then press the START button.

The door must be closed and latched into place to select a cycle or an option.

To interrupt/pause a cycle, press the selected cycle button. The Status Indicators will flash.

CAUTION: Be careful when opening the door; the hot steam that escapes when the door is

opened may cause injuries. Stand back as you open the door and allow the steam

to escape.

ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui s’échappe

lorsque vous ouvrez la porte pendant un programme de lavage peut causer des

brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur s’échapper

de l’appareil.

To restart the wash process, close the door until it locks in place. Re-press the cycle button. There

may be a time delay of up to a few minutes, because the temperature inside the Chef’s Washer

needs to stabilize before it restarts the wash cycle. During this time the SENSING light will be on.

To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.

The Chef’s Washer will then drain and the cycle indicator lights will flash. At this point a new wash

cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out after the

Chef’s Washer drains. If you have selected a new wash cycle, remember to add more detergent to

the detergent compartment if required.

Control Panel/Operation – ZBD6905

Chef’s Washer

NSF INTERNATIONAL

Meets NSF Protocol for Performance of Domestic Spray-Type Pots

and Pans Washing Machines (NSF Protocol P180) Requirements for

cleaning and sanitization of cookware.

1. Cycle Selections–The light on the selected pad will illuminate to indicate which cycle has been

selected.

HEAVY DUTY For pans or cookware with dried-on or baked-on soils.

This cycle may not remove some burned-on foods.

NORMAL WASH For loads of everyday cookware with medium soils. NOTE: For heavily soiled

cookware, choose NORMAL WASH plus HIGH water temperature option.

LIGHT WASH For lightly soiled cookware or recently used, lightly soiled cooking utensils

and cookware to be washed in a short time.

RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent with

this cycle.

2. WATER TEMP–This button provides extra heat options to increase water temperature for

optimum performance.

NORMAL This is the default setting–provides a wash and rinse with water temperatures

up to 125°F (51°C) in LIGHT WASH, 135°F (57°C) in the NORMAL WASH

cycle and 155°F (68°C) in HEAVY DUTY.

HI TEMP This water temp selection provides a wash and rinse with water temperatures

up to 160°F (71°C) in LIGHT WASH, NORMAL WASH and HEAVY DUTY.

SANITIZE This water temp selection provides a sanitizing wash and rinse with water

temperatures up to 160°F (71°C) in LIGHT WASH and 171°F (77°C) in NORMAL

WASH and HEAVY DUTY. This selection cannot be used with RINSE ONLY.

At the end of the wash cycle, the SANITIZE OPTION light will remain

illuminated to indicate that the sanitization conditions have been met.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

3. SMART DRY–When selected, sensors detect the presence of rinse aid and the final rinse

temperature. The drying heater and fan are then turned on for the minimum time to achieve

optimum drying results, saving energy over conventional heated dry and time over non-heated

dry. SMART DRY is not available on RINSE ONLY.

Control Panel – ZBD7005 & ZBD7105

Chef’s Washer

ZBD7005 & ZBD7105

Control

Settings

1 3 42

You can locate

your model

number on the

inside upper

tub flange.

Throughout this

manual, features

and appearance

may vary from

your model.

NSF INTERNATIONAL

Meets NSF Protocol for Performance of Domestic Spray-Type Pots

and Pans Washing Machines (NSF Protocol P180) Requirements for

cleaning and sanitization of cookware.

To start the Chef’s Washer, open the Chef’s Washer door so that the top-of-door controls are

visible. The last used cycle will be displayed. To begin this cycle, press the START button. To select

a different cycle, press the desired Cycle Selection and Option buttons, and then press the START

button. After the door is closed and latched, the selected cycle will begin.

To interrupt/pause a cycle, gently open the door just enough to turn off the wash motor. Do not

fully open the door until the wash action ceases.

WARNING: Do not fully open door while the Chef’s Washer is in operation. Quickly opening

the door while the Chef’s Washer is operating could result in serious scalding.

Be careful when opening the door; the hot steam that escapes when the door

is opened may cause injuries. Stand back as you open the door and allow the

steam to escape.

AVERTISSEMENT : N’ouvrez pas complètement la porte lorsque la laveuse fonctionne. Une

ouverture rapide de la porte lorsque l’appareil est en fonctionnement

peut entraîner de sérieuses brûlures. Faites attention lorsque vous ouvrez

la porte; la vapeur brûlante qui s’échappe lors de l’ouverture de la porte

peut causer des blessures. Tenez vous en arrière lorsque vous ouvrez la

porte afin de permettre à la vapeur de s’échapper.

To restart the wash process, close the door until it locks in place. There may be a time delay of

up to a few minutes because the temperature inside the Chef’s Washer needs to stabilize before

it restarts the wash cycle.

To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.

The Chef’s Washer will start to drain and the cycle indicator lights will flash. At this point a new

wash cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out

after the Chef’s Washer drains completely. If you have selected a new wash cycle, remember to

add more detergent to the detergent compartment if required.

Start a

Wash Load

Control Panel/Operation – ZBD7005 & ZBD7105

Chef’s Washer

Control

Settings

4. DELAY START–This option will allow you to delay the start time of any wash cycle except

RINSE ONLY for up to 6 hours.

• Select the delay start time you want by pressing the DELAY START button. Multiple pressing

will alternate the delay time between 2, 4 or 6 hours and OFF.

Features – ZBD6605, ZBD6905, ZBD7005, ZBD7105

Chef’s Washer

Auto

Memory

Your Chef’s Washer has the ability to remember what options you like with NORMAL WASH and

HEAVY DUTY wash cycle. This means that if you select NORMAL WASH, your Chef’s Washer will

automatically select the options that you selected last time you washed with the NORMAL WASH cycle.

You can change the options that have been remembered with a particular wash cycle if you desire.

Child

Lockout

Mode

(on some

models)

To reduce the possibility of children starting the Chef’s Washer when unattended, a child lockout

feature can be enabled. Once enabled, each button must be pressed and held for two seconds until

you hear a BEEP, before the Chef’s Washer will respond. While in this mode, the SENSING and

CLEAN light will illuminate while the button is pressed.

This feature can be enabled by pressing both the START/CANCEL and HEAVY DUTY buttons

together and holding both for two seconds. You will hear three BEEPS when the child lockout

is enabled.

The child lockout can be cancelled by pressing the START/CANCEL and HEAVY DUTY together

and holding both pressed for two seconds until a single BEEP is heard.

NOTE: Child lockout overrides tone silencing.

Tone

Silencing

(on some

models)

You can prevent the beep from sounding when selecting control settings.

1. Press the START/CANCEL and NORMAL WASH buttons together prior to selecting settings.

2. To have sound again, simply press the START/CANCEL and NORMAL WASH buttons

together again.

Detergent

Usage

Guide

(Powder or

Liquid)

SOFT WATER MEDIUM WATER HARD WATER

0–3 grains 3–7 grains 7–12 grains*

CYCLES Main Cup Auxiliary Cup Main Cup Auxiliary Cup Main Cup Auxiliary Cup

HEAVY DUTY Full None Full Full Full Full

NORMAL WASH

⁄2 Full None Full None Full Full

LIGHT WASH

⁄2 Full None Full None Full Full

SPEED WASH

⁄2 Full None Full Full Full Full

RINSE ONLY Use no detergent Use no detergent Use no detergent

*12 grains and up is extremely hard water. A water softener

is recommended. Without it, lime can build up in the water

valve. The water valve may stick and flooding could occur.

NOTE: The above chart is a general guide. Detergent

amounts should be adjusted depending on the amount

and type of soil until satisfactory results are achieved.

Cycle Chart

APPROXIMATE CYCLE TIME

With 120°F Water

TEMPERATURE (°F) (excluding drying time)

Sani

(on some

CYCLES Normal High models) Normal High Sani

HEAVY DUTY 155 160 171 7.4 70 77 84

NORMAL WASH 135 145–160 160–171 5.0–11.2 50 94 80

LIGHT WASH 125 135–160 160 5.0 30 50 63

SPEED WASH 115–125 — — 3.8 23 — —

RINSE ONLY — — — 1.2 11 — —

WATER USAGE

(Gallons)

Use only detergent specifically made for use in

dishwashers. Keep your powdered detergent

fresh

and dry. Don’t put powder detergent into

the

dispenser until you’re ready to wash dishes.

The amount of detergent to use depends on

whether your water is hard or soft. With hard

water, you need extra detergent. With soft

water, you need less detergent.

Protect your dishes and Chef’s Washer by

contacting your water department and asking

how hard your water is. Twelve or more

grains

is extremely hard water. A water softener is

recommended.

Without it, lime can build up

in the water valve, which could stick while open

and cause flooding. Too much detergent with

soft water can cause a permanent cloudiness

of glassware, called etching.

To open the detergent compartment, push the

lever latch inward.

When using automatic dishwashing detergent

tabs, place one tab in the main cup and close.

Be sure the Cycle Status Indicators (on some

models) are not lit before adding detergent.

Otherwise, the detergent cup will not close and

latch properly. Add detergent, then close the

main cup.

NOTE: To open detergent cup after it has been

closed, push the lever latch inward.

Lever

Main compartment

Using the Chef’s Washer

Chef’s Washer

Detergents

Water

Temperature

The entering water must be at least 120°F

(49°C) and

not more than 150°F (66°C), for

effective cleaning and to prevent dish damage.

Check the water temperature with a candy or

meat thermometer. Turn on the hot water

faucet nearest the Chef’s Washer, place

the thermometer in a glass and let the water

run continuously into the glass until the

temperature stops rising.

Use a

Rinse

Agent

A rinse agent improves dry performance,

reduces spots and prevents new film buildup

on your dishes, glasses, flatware, cookware

and plastic.

Fill the rinse agent chamber by rotating the

round cap counterclockwise and remove. Fill

chamber to maximum level. Replace and lock

the cap into place.

To check if rinse agent is needed: a solid black

indicator indicates sufficient rinse agent; a clear

indicator indicates a low level and requires

adding more rinse agent.

• A full dispenser should last about one month.

• If rinse agent spills, wipe it up immediately.

It can keep your detergent from working.

•

If after washing you notice cloudy spots,

streaks or water marks on the glassware, and

the rinse agent dispenser is not empty, it may

be necessary to increase the dispenser settings.

To do so, remove the cap and using a butter

knife, rotate the indicator arrow to a higher

number. Replace the cap when done.

•

If glasses appear smeared or there is foam

present on the bottom of the glasses or the

bottom of the machine, select a lower dosage

number.

•

For softened water, reduce dispenser setting.

Light level indicator

Adjust to higher or lower number

Auxiliary

compartment

Loading the Racks

Chef’s Washer

Upper Rack

The upper rack is for small bowls and pans. This is

also a secure place for dishwasher-safe plastics.

Because bowls and casserole dishes come in various

sizes, after loading, slowly push in the rack to make sure

they will clear the top of the Chef’s Washer.

The upper rack is also good for all kinds of oddly-

shaped utensils. Saucepans, mixing bowls and other

items should be placed face down.

Make sure small plastic items are secure so they can’t

fall onto the heating element.

Upper

Wash

Tower

Take care not to obstruct the rotation of the

spray arm under the upper rack or cover the

water collector in the center of the upper rack.

Squeeze

Re-adjust

upper rack

Adjusting

Upper Rack

Height

The upper rack can be raised or lowered to

provide extra room for different sized items.

Empty the upper rack. Remove the rail pegs

in the front of the rack runners by squeezing

and lifting the top of the peg, then slide the

rack out.

Re-insert the rack in the chosen position and

replace the pegs. Check that the spray arm is

free to rotate.

Lift peg from

rack runner

This Chef’s Washer is designed for dishwasher-safe gourmet cookware.

Lower Rack

When loading the lower rack, do not load tall platters

or trays in the front left corner. They may prevent

detergent cup from opening during the wash cycle.

The lower rack is best used for large trays, saucepans

and cookware. There is 15″ clearance for tall items.

Large items such as broiler pans and racks should go

along the sides. Load platters, pots and bowls along

the sides, in corners or in the back. The soiled side

of items should face down or the center of the rack.

Fold-down tray dividers provide flexibility for extra

large and hard-to-fit items.

The tray dividers may be left in the up position or

folded down to customize the lower rack.

Silverware

and Utensil

Basket

Put flatware in the removable basket with fork and knife handles up to protect your hands. Place

spoons in the basket with handles down. Mix knives, forks and spoons so they don’t nest together.

Distribute evenly. Small plastic items, such as measuring spoons and lids from small containers,

should go in the bottom of the silverware basket with silverware on top.

Flip-down covers can be lowered to secure lightweight items from the effects of the vigorous wash

action. The slots in the covers can be used to separate silverware.

Don’t let any item extend through bottom

Tray Divider

Care and Cleaning

Chef’s Washer

Exterior

To clean the control panel, use a lightly dampened cloth, then dry thoroughly. To clean the

exterior painted panels, use a good appliance polish wax.

Never use sharp objects, scouring pads or harsh cleaners on any part of the Chef’s Washer.

Use stainless steel cleaner on stainless steel panel. You can order

Stainless Steel Magic # WX10X15

through GE Parts in the USA, by calling 800.626.2002. In Canada, call 1.888.880.3030.

Protect

Against

Freezing

If your Chef’s Washer is left in an unheated place during the winter, ask a service technician to:

1. Cut off electrical power to the Chef’s Washer. Remove fuses or trip circuit breaker.

2. Turn off the water supply and disconnect the water inlet line from the water valve.

3. Drain water from the water inlet line and water valve. (Use a pan to catch the water.)

4. Reconnect the water inlet line to the water valve.

5. Remove the filters from the tub bottom and use a sponge to soak up water.

The Air

Gap

An air gap protects your Chef’s Washer against

water backing up into it if a drain clogs. The air

gap is not a part of the Chef’s Washer. It is not

covered by your warranty. Not all plumbing

codes require air gaps, so you may not have one.

The air gap is easy to clean.

1. Turn off the Chef’s Washer and lift off the

chrome cover.

2. Unscrew the plastic cap and clean with

a toothpick.

Interior

The stainless steel tub can be cleaned with Stainless Steel Magic or a similar product using

a clean, soft cloth.

Use stainless steel cleaner on stainless steel panel. You can order

Stainless Steel Magic # WX10X15

through GE Parts in the USA, by calling 800.626.2002. In Canada, call 1.888.880.3030.

Wipe the rubber door seals occasionally, including the seal at the bottom of the door.

Check the air gap any time your Chef’s Washer

isn’t draining well.

Two types

of air gaps

Removing

and Cleaning

the Spray

Arms and

Glass Trap

Periodically, remove and clean the spray arms

to make sure that none of the nozzles have

become blocked.

To remove the lower spray arm, grasp the

center of the spray arm and pull upward; it will

unclip. When replacing, make sure the spray

arm is fully seated and spins.

The plastic cone on the underside of the

spray arm can be detached by unscrewing it

counterclockwise.

To remove the upper spray arm, carefully

unscrew the spray arm from the plastic tower.

To achieve this, hold the inner tower steady

and unscrew the spray arm clockwise. To

replace the spray arm, carefully screw the spray

arm counterclockwise onto the inner tower.

To clean the upper and lower spray arms,

rinse them under running water and make

sure spray nozzles are clear.

The glass trap is located in the stainless steel

filter at the base of your Chef’s Washer. The

glass trap is used to collect larger food items

and other foreign objects, which may be too

big to pass through the drain pump. For best

wash performance, check the glass trap

occasionally.

To remove the glass trap, twist counterclockwise,

rotate the glass trap

and lift. To clean the glass

trap, empty and rinse thoroughly. To replace,

reverse these steps, making sure the glass trap

locks into place.

Pull up to remove

Rotate counterclockwise and

lift to remove glass trap

Rotate counterclockwise

to remove cone

Care and Cleaning

Chef’s Washer

The Wash

Filters

In addition to the glass trap, your Chef’s

Washer has three fine filters–

• a two piece round perforated stainless steel

filter located in the base of the Chef’s Washer.

• a finer micro-mesh filter located under the

stainless steel filter.

• a super fine filter located below the lower

spray arm.

Remove the stainless steel filter by first twisting

and removing the glass trap. Lift out the

stainless steel filter.

Attached to the underside of this filter is the

micro-mesh filter. To remove the micro-mesh

filter, squeeze the two clips above the stainless

steel filter to release the micro-mesh.

To remove the super fine filter, remove the

lower spray arm. Grasp the super fine filter

around the outer edges. Remove by pulling

upward; it will unclip. Unscrew the tower

counterclockwise. The right half of the stainless

steel filter can now be removed.

To clean filters, place under running water

and gently brush with a soft bristled brush.

Be careful not to deform filters while cleaning,

this may prevent them from being properly

re-installed.

The super fine filter is self-cleaning; there is

no need to clean it. This filter need only be

removed if you want to remove the right half

of the stainless steel filter.

Replace your filters in the reverse order,

starting with the right half of the stainless

steel filter. Then screw in the tower. Replace

the super fine filter over the tower by pressing

firmly on the outer edge until it clips into

place and reposition the lower spray arm.

Reconnect the micro-mesh filter to the left

half of the stainless steel filter prior to

replacing it back into the Chef’s Washer. Then

replace the glass trap. Ensure that all filters

are replaced correctly for best results.

Grip filter and lift

to remove

Perforated stainless

steel filter

Micro-mesh filter

Squeeze clips to remove

micro-mesh filter

Pull super fine

filter up to remove

Lift stainless steel

filter to remove

La page charge ...

Monogram ZBD7105 Manuel utilisateur

Marque: Monogram

Modèle: ZBD7105

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Monogram ZBD7105 User manual

Monogram ZBD7105 Manuel utilisateur

Monogram ZBD7105 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents