Honeywell SIX Series Guide d'installation

Marque: Honeywell

Modèle: SIX Series

Taper: Guide d'installation

SiXMEDICAL

1-Button Wireless Key

Installation Instructions

This bi-directional wireless key is intended for

use with Honeywell controls that support SiX™

series devices.

To activate, press and hold the button about 3

seconds until the LED flashes.

To clear the alarm

at the control, enter a user code. To clear

memory of alarm, select Disarm and enter a user

code.

The device can be used with a belt clip, lanyard,

or wristband.

[images of belt clip, wristband, necklace]

LED Indications

Green flashing: lights when unit is transmitting

Red Flashing: indicates low battery (lights

during key press)

Enroll and Program the SiXMEDICAL

For the Lyric™ Controller

Follow instructions in the Controller’s programming guide.

1. Set the Lyric Controller in Programming Mode: Security >

Tools > [installer code] > Program > (scroll down) > SiX

Programming.

2. Press and hold the button for about 3 seconds until the LED

flashes to activate the enrollment process.

3. The LED flashes green during enrollment (up to about 20

seconds).

NOTE: Enrollment time varies depending on the signal

strength between the device and the controller.

• The device sends its unique MAC ID (Serial Number) and

Services information to the controller.

• The controller registers the device and displays the

transmitter data on screen.

4. When done, the LED lights solid green for 3 seconds to

confirm enrollment.

If enrollment is not confirmed, press and hold the button again

for about 3 seconds to restart the enrollment process.

5. Press Edit to set the Alarm Report option on/off (if selected,

button press sends a report to the central station). Press

Save. Enter an appropriate Zone Descriptor. Press Save.

The device can also be manually enrolled. See the Controller’s

Programming Guide for details.

For the Lyric™ Gateway

Enroll and program using AlarmNet 360™.

For other Controls

For other Controls that support SiX Series devices, see the

controller’s instructions for enrollment details.

IMPORTANT: Once enrolled in a system, the SiXMEDICAL

cannot be used with another controller until it is removed from the

current controller. When removed from a system, the key fob will

revert to factory default settings.

Sensor Location Feature: To verify the location of each SiX

device in an installation, enter programming mode and select a

SiX device. The device LED lights. Select it again to turn the LED

off, or select the next device to locate.

After Enrolling: Verify adequate signal strength by conducting

Go/No Go tests (see controller’s instructions) with the device in

its intended mounting location. Adjust the device location as

necessary.

24-Hour Enrollment Deletion and Default

If the device is enrolled in a panel different than the

intended panel, and you are unable to delete it from the

unintended panel, reset the device to factory default

setting:

Press and hold the button for 15 seconds.

The device self-deletes from the panel it was enrolled in.

This procedure is available for 24 hours after enrollment

with a panel and the device remains powered (battery

installed).

Press and hold button 15 seconds.

Battery Replacement

When the battery is low, the LEDs do not flash during

transmission. To replace the battery:

1. Remove the screws from the back housing and use a

screwdriver to gently separate the front and back housings.

2. Use a screwdriver to carefully remove the battery.

3. Wait 10 seconds or press a key fob button for 2 seconds to

ensure full power discharge.

4. Insert a new 3V Coin Cell battery as shown. Recommended

replacement battery:

Recommended Batteries: 3V Coin Cell

Honeywell BL3-0004 (CR2450); Duracell DL2450;

Panasonic CR2450; Energizer CR2450

Replace the front housing and secure the housings with the

cover screw.

Replacing the Battery

BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge,

disassemble, heat above 212 F (100 C) or incinerate. Dispose of used

batteries properly. Keep away from children.

NOTE: Constant exposure to high or low temperature or high humidity

may reduce battery life.

Specifications

Battery: 1 x 3V Coin Cell, Honeywell BL3-0004 (CR2450); Duracell DL2450;

Panasonic CR2450; Energizer CR2450

RF Frequency: 2.4GHz

Operating Temperature: 0° to 50° C / 32° to 122° F

(Agency compliance 0° to 49° C / 32° to 120° F)

Relative Humidity: 95% max. (Agency compliance – 93% max.),

non-condensing

Dimensions: 0.5” H x 1.5” L x 1.5” W / 13 mm H x 38 mm L x 38 mm W

Approval Listings:

FCC / IC

cETLus Listed

Conforms to UL 1023 & UL 985

Certified to ULC ORD- C1023

& ULC-S545

Other Standards:

SIA CP-01 RoHS C-Tick

Product must be tested at least once each year.

IMPORTANT! This wireless key is intended as a convenience to the user and should not be considered as a life safety device.

IMPORTANT SECURITY NOTICE

Please inform the User about the security importance of their wireless key (key fob), and what to do if it is lost.

Explain that the key fob is similar to their keys or access card. If lost or stolen, another person can compromise their security

system. They should immediately notify the Dealer/Installer of a lost or stolen key fob. The Dealer/Installer will then remove the

key fob programming from the security system.

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes

or modifications could void the user's authority to operate the equipment.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement est soumis aux conditions

suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant

une réception indésirable.

RF EXPOSURE

Warning – The antenna(s) used for this device must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with

FCC and ISED multi-transmitter product procedures.

Mise en Garde

Exposition aux Fréquences Radio : La/les antenne(s) utilisée(s) pour cet émetteur ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou