Lightspeed Redcat media Manuel utilisateur

User Manual

Classroom Audio System

CH APWR CH B

TABLE OF CONTENTS

SECTION 1: 5 System Components and Unpacking

Overview 6 Optional Components

7 Front Panel Indicators

7 Top Panel Controls

8 Side Panel Controls and Connections

8 Rear Panel Controls and Connections

9Redmike Controls and Connections

10 Cradle Charger Controls and Connections

SECTION 2: 11 Step 1. Determine Set-up Location

Set-up & Use 11 1A. To Set-Up on Table Top

12 1B. To Set-Up Mounted on a Wall

13 1C. Wall Mounting Locations

14 Step 2. Connecting the Power Supply

15 Step 3. Audio Integration

16 Step 4. Charging the Redmike

17 Operating the Redmike

18 Output to Assistive Listening Device (ALD)

19 Using Redmike as Wireless Audio Link

SECTION 3: 20 Optional Redmike VC Controls and Connections

Optional

Accessories

21 Redmike VC: Charging

21 Redmike VC: Intial Set-up

22 Redmike Share: Controls and Connections

23 Redmike Redmike Share: Charging

24 Redmike Share: Initial Set-up

25 Initial Set-up: Optional iRMC Media Connector

26 Optional iRMC Media Connector Audio

Integration

26 Optional Accessories

SECTION 4: 27 Common Problems and Solutions

Troubleshooting 28 Tips to Obtain Optimum Audio Performance

SECTION 5: 29 Five-Year Limited Warranty

Warranty, Safety 30 Safety Warnings and Certiﬁcations

& Speciﬁcations 34 System Speciﬁcations

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use the apparatus near

water.

6. Clean only with dry cloth.

7. Do not block any ventilation

openings. Install in accordance

with the manufacturer’s

instructions.

8. Do not install near any heat

sources such as radiators,

heat registers, stoves, or other

apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose

of the polarized or grounding-

type plug. A polarized plug

has two blades with one wider

than the other. A grounding-

type plug has two blades and

a third grounding prong. The

wide blade or the third prong is

provided for your safety. If the

provided plug does not fit into

your outlet, consult an electrician

for replacement of the obsolete

outlet.

10. Protect the power cord from

being walked on or pinched

particularly at plugs, convenience

receptacles, and the point where

they exit from the apparatus.

11. Only use attachments/

accessories specified by the

manufacturer.

12. Use only with a cart, stand, tripod,

bracket or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used,

use caution when moving the

cart/apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during

lightning storms or when unused for

long periods of time.

14. Refer all servicing to qualified

service personnel. Servicing is

required when the apparatus has

been damaged in any way, such

as power-supply cord or plug is

damaged, liquid has been spilled

or objects have fallen into the

apparatus, the apparatus has been

exposed to rain or moisture, does

not operate normally, or has been

dropped.

15. When the mains plug or appliance

coupler is used as the disconnect

device, it shall remain readily

operable.

16. Please keep the unit in a good

ventilation environment.

17. WARNING: To reduce the risk of ﬁre

or electric shock, do not expose this

apparatus to rain or moisture.

18. Apparatus shall not be exposed to

dripping or splashing and no objects

ﬁlled with liquids, such as vases, shall

be placed on the apparatus.

19. Warning - battery pack shall not be

exposed to excessive heat such as

sunshine, fire or the like.

5

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

SECTION 1:

OVERVIEW

SYSTEM COMPONENTS AND UNPACKING

The standard conﬁguration of the Redcat® will contain:

Redcat® Infrared

Receiver/Ampliﬁer

and Power Supply

CH APWR CH B

Cradle Charger

and Power Supply

Redmike®

Classroom

Microphone

6

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

OPTIONAL COMPONENTS

Redmike® VC

Volume Control

Microphone

Redmike® Share

Handheld Mic &

Charging Cable

Optional equipment which may be part of your Redcat system:

RC2 Redcat all-in-one receiver/ampliﬁer/speaker with power supply

24V-1.75-NA Power supply for Redcat

24V-1.75-_ Power supply for Redcat, specify country

RMT2 Redmike classroom microphone with rechargeable battery and

lavalier cord

NH2A27 Lightspeed AA rechargeable sensing battery

(for Redmike)

RMLC3 Lavaliere cord for Redmike

RMCC Redmike cradle charger

5V-1.0-NA Cradle charger power supply

5V-1.0-INT Cradle charger power supply, universal plug attachment

STANDARD COMPONENTS

OPTIONAL COMPONENTS

RMV2 Redmike VC microphone with battery

RMS2 Redmike Share handheld microphone with battery pack

NH2APK NiMH rechargeable battery pack for Redmike Share

IRMC2 Infrared media connector with cables and power supply

WMKRC2 Redcat wall mounting kit includes screws, wall anchors, security clip

and extra RC feet

7

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

FRONT PANEL INDICATORS

1. POWER ON INDICATOR: The power LED will glow

blue when power is applied.

2. CH A & CH B: Illuminate red when the audio for the

corresponding microphone is received.

CH APWR CH B

122

TOP PANEL CONTROLS

1. CHANNEL A VOLUME: Controls the volume level of the

microphone set to channel A.

2. CHANNEL B VOLUME: Controls the volume level of the

microphone set to channel B.

MICROPHONE

CH A CH B

MINMINMAXMAX

12

8

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

SIDE PANEL CONTROLS / CONNECTIONS

1. TONE CONTROL: Adjusts the audio

level for optimum sound quality.

2. AUDIO INPUT VOLUME CONTROL &

INPUT JACK: 3.5mm stereo connector

for connecting classroom audio sources

to the Redcat. Controls the volume level

of the audio input from the connected

audio source.

3. AUDIO OUTPUT VOLUME CONTROL

& INPUT JACK: 3.5mm stereo

connector for connecting to an assisted

listening device (ALD) or to a computer

for recording. Controls the volume level

of the audio output.

4. POWER SWITCH: This switch is used

to turn the Redcat on or off. The front

panel blue LED lights when power is on.

5. DC POWER INPUT JACK: Plug the

power supply (24V/1.75A) into this jack.

2

1

4

5

3

REAR PANEL FEATURES

1. CARRYING INSET: Cutaway grip for moving or carrying

the Redcat Access.

2. CABLE MANAGEMENT AND STRAIN RELIEF

3. WALL MOUNTING SLOTS

4. SECURITY BRACKET SLOT

Testing Purposes Only

1

23

4

9

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

1. POWER BUTTON: Press this

button to turn the Redmike on,

press again to turn it off (mute).

2. POWER/LOW BATTERY

INDICATOR: A blue light

indicates the Redmike is on and

fully charged. A red light indicates

a charge is needed.

3. BATTERY COMPARTMENT: To

access the battery compartment,

slide the door downward. The

battery should only be replaced

by a Lightspeed AA rechargeable

sensing battery (part # NH2A27).

4. YELLOW PROTECTIVE TAB: Slide

the battery compartment door

open to remove this disposable

protective tab before use. NOTE:

do not attempt to remove the

tab without ﬁrst opening the

compartment door, as it may tear,

leaving fragments.

5. AUDIO/MICROPHONE INPUT:

Use this input to plug in a laptop,

MP3 player or other audio

source to wirelessly transmit

audio to be played through the

system. Alternatively, an external

microphone can be connected.

6. CHANNEL SELECT SWITCH

(CH A/B): This switch allows

for selection between Channel

A or B. If you are using a single

microphone, we recommend using

Channel A.

7. CHARGER CONTACTS (+ -):

These contacts interface with the

charging tabs in the RMCC cradle

charger for daily charging. Simply

place the Redmike in the charger.

REDMIKE CONTROLS AND CONNECTIONS

1

2

3

5

6

7

S

li

d

e

b

at

t

e

ry

d

o

r

o

p

e

n

R

e

m

o

v

e

t

a

b

e

fo

r

e

u

s

e

4

10

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

1. CHARGE INDICATORS: The light

glows red while the Redmike is

charging. When fully charged, the

light will glow green. A blinking

red light indicates that no battery

is sensed, (Redmike Yellow

Protective Tab may not have been

completely removed—see page

10, item 4.) A blinking green LED

means a non- Lightspeed battery

has been installed (possibly an

alkaline battery).

2. DC POWER PORT: Connect the

5V/1.0A DC power cord here.

3. OPTIONAL CHARGING PORT:

Plug the charging cord for

the optional Redmike Share

microphone here.

CRADLE CHARGER CONTROLS AND

CONNECTIONS

1

2

3

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

11

The Redcat is shipped with feet to stand on a cabinet or tabletop. Alternatively,

the feet can be used as wall mount brackets.

Advantages of either include:

SECTION 2:

SET-UP & USE

1. DETERMINE SET-UP LOCATION

1A. TO SET-UP ON TABLE-TOP

Tabletop (recommended):

• Virtually no setup time

• Greater ﬂexibility to move to

different locations

First, consider that the Redcat should

be placed within 7 feet of an electrical

outlet and on a surface about 3-6 feet

off the ground.

Next, ﬁnd a location as far away as

possible from the teacher who will

be using the mic. The best place is

against the wall opposite where the

teacher will be speaking. If this is not

possible, other good locations are

along either wall next to the teacher

or in a corner. Avoid placing the

Redcat next to where the teacher

instructs. Putting the Redcat s in close

proximity to the teacher’s mic can

result in feedback.

Wall-mount:

• More permanent setup

• Greater security

Avoid!

Good placement Best placement

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

12

1B. TO SET-UP MOUNTED ON A WALL

First, consider that the Redcat should

be placed within 7 feet of an electrical

outlet and about 6-8 feet off the

ground.

Next, ﬁnd a location as far away as

possible from the teacher who will

be using the mic. The best place is

centered on the long wall opposite

the teacher. If this is not possible,

other good locations are on the wall

next to the teacher. Avoid placing the

Redcat on any wall close to where

the teacher usually stands to instruct

the class. Having the teacher’s mic

too close to the Redcat can result in

feedback.

Good placement

Best placement

Avoid!

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

13

1B. TO SET-UP MOUNTED ON A WALL CONT’D

1. Level template and tape to wall

2. Mark position of drill holes on wall

3. Drill pilot holes

4. Insert anchors

5. Remove feet from Redcat and place over anchors

6. Insert and secure screws through the Redcat feet into the anchors

7. If using optional security bracket, mount on wall using the

provided screws and anchors

8. Slide the Redcat onto the wall mounted feet

Drill Template

for wall-mounting the REDCAT System

Drill holes

Instructions

Determine the best location for the REDCAT,

refer to the user manual provided with this

product. For wall mounting, the REDCAT

should be mounted 7 to 8 feet from the ﬂoor.

1. Start by leveling this template and taping

to the desired location on the wall.

2. Mark the hole locations using a sharp

pencil. (7 locations)

3. Drill pilot holes

4. Insert anchors

5. Insert screws through the feet and tighten

to the wall

6. Insert screws through the security tab

bracket and tighten to the wall.

7. Slide the REDCAT onto its mounted feet.

If the safety tab is installed, it should snap

into place preventing system removal.

Materials Required

Drill Bit: Size appropriate for the

anchors or screws being used.

Anchors: Needed for mounting

on drywall, plasterboard, or

cement block.

Screws: Wood screws or screws

appropriate for anchors.

Security Tab

Foot Foot

IG0432US01-0 AC-IGRC2DT

OR

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

14

1. Locate the power supply and

AC power cord. Connect the AC

power cord into the DC power

supply.

2. Insert the DC connector into the

“DC INPUT” connector on the

Redcat and plug the other end to

an electrical outlet.

3. Power on the Redcat by pressing

the power button.

2. CONNECTING THE POWER SUPPLY

Power On

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

15

Audio Input

The Redcat has one AUDIO INPUT with volume control for connecting to

classroom audio sources. Use a patch cable (not included) to connect a

computer, iPod, iPad, or other audio source.

3. AUDIO INTEGRATION

The next step in setting up your Redcat system is to connect it to the other

elements of your audio system. Audio systems have varying elements – you

may have a computer, television, DVD/VCR player, a visual projection system

or other devices. In this section you will ﬁnd instructions on how to connect an

external audio device like a TV, VCR, DVD, MP3 or computer directly into the

Redcat.

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

16

4. CHARGING THE REDMIKE

Before use, the Redmike should be charged. It will take 8-9 hours for the

Redmike to obtain a full charge. A fully charged Redmike will last for over 7

hours of use. If microphones are used daily, they should be kept in the cradle –

microphones can be left in a charging cradle constantly for up to 2 weeks without

causing degradation to battery life.

A red light on the charging cradle indicates the Redmike is charging. A green

light indicates that charging is complete and a full charge has been reached. A

blinking light indicates a charging or sensing error. See Troubleshooting section

for more information.

Redmike incorporates alkaline protection into the microphone design. Always

use a Lightspeed rechargeable sensing battery. Replacement AA NiMH batteries

may only be purchased through Lightspeed Technologies (part # NH2A27). Do

not attempt to charge alkaline batteries. They can overheat and expand creating

a signiﬁcant hazard and damaging the microphone (this is not covered by

warranty).

1. Plug power cord into the cradle

charger and then plug the AC end

into an electrical outlet.

2. Place the Redmike into the cradle.

The LED on the cradle will glow

red indicating charging has

started. When the Redmike is fully

charged the LED on the cradle

charger will change to green.

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

17

5. OPERATING THE REDMIKE

Once the Redmike is charged, follow these steps to set it up for use.

1. Turn the Redcat power on. The

blue LED will glow.

2. Remove the Redmike from the

charging cradle and turn it on.

3. Slip the Redmike with lanyard

around the neck. The top of the

microphone will be approximately

just below the collarbone.

4. Slowly increase the channel A/B

volume up to the ‘green’ section

of the dial. This designates normal

volume range in the classroom.

5. While speaking in a normal voice,

ﬁne-tune the volume up or down.

Proper volume level should be as

follows:

a. Your voice should be clearly

heard by another person on the

other side of the room.

b. You should barely be able to

hear your own voice.

c. There should not be any audio

“feedback” or squealing outside

of 2-3 feet (if there is, turn the

volume down slightly).

REMEMBER: This equipment

supplements the user’s voice so they

are able to speak in a conversational

tone. Having the volume set too high

will result in feedback and listener

fatigue.

6. Once initial volume level is set,

walk around the room and listen

for audio dropout and overall

audio quality.

7. If a second Redmike was

purchased, repeat steps 2-4.

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

18

1. Turn the ALD (Assistive Listening

Device) volume control

on the Redcat side panel

counterclockwise all way the down.

2. Determine the size and type of

audio input jack on the device as

many manufacturers’ products

differ in connector size and shape.

The Lightspeed 370 Transmitter

requires a 3.5mm to 3.5mm

patch cable (part# MSC3535, not

included).

3. Connect a patch cable from the

ALD’s microphone jack or AUX

input to the 3.5mm audio jack

labeled “ALD OUT” on the side

of the Redcat.

4. With the Redcat and ALD turned

on, speak into the Redmike and

slowly adjust the ALD volume

control until the appropriate

audio level is attained in the ALD’s

receiver headphones.

5. It may be necessary to adjust

the volume on the Personal FM

receiver to achieve appropriate

volume level.

6. OUTPUT TO ASSISTIVE LISTENING

DEVICE (ALD)

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

19

USING REDMIKE TO AMPLIFY

EXTERNAL AUDIO EQUIPMENT

The Redmike includes a 3.5mm audio input jack to connect to an audio source

like a laptop or MP3 player. The Redmike will transmit the audio signal to be

played through the system.

If your system includes two Redmikes, we recommend using Channel B (student

mike) to amplify the external audio equipment so the teacher’s volume on the

Channel A (teacher mike) does not have to be adjusted.

To determine which Redmike is set to Channel B, you can look at the switch on

the back of the mike or speak into one of the mics and watch which set of LED’s

glow on the front panel of the Redcat (A Volume or B Volume correspond to

Channels A or B).

1. Plug your external audio

equipment (for example, laptop),

into the input on the Redmike

labeled “INPUT” using a 3.5mm

patch cable.

AUDIO

OUTPUT

AUDIO

INPUT

2. Adjust the volume of the selected mic

channel to achieve desired loudness.

MICROPHONE

CH A CH B

MINMINMAXMAX

20

1. Overview 2. Setup & Use 3. Optional

Accessories 4. Troubleshooting 5. Warranty, Safety

& Speciﬁcations

SECTION 3:

OPTIONAL ACCESSORIES

OPTIONAL Redmike VC (Volume Control)

Controls and Connections

5

6

7

8

1

2

3

S

li

d

e

b

at

t

e

ry

d

o

r

o

p

e

n

R

e

m

o

v

e

t

a

b

e

fo

r

e

u

s

e

4

1. POWER /MUTE BUTTON

2. POWER/LOW BATTERY

INDICATOR: A blue light

indicates the Redmike VC is on

and fully charged. A red light

indicates a charge is needed.

3. BATTERY COMPARTMENT: To

open, slide the door downward.

The battery should only be

replaced by a Lightspeed AA

rechargeable sensing battery

(part # NH2A27).

4. YELLOW PROTECTIVE TAB: Slide

the battery compartment door and

remove this disposable protective

tab before use.

5. AUDIO/MICROPHONE INPUT:

Use this input to plug in a laptop,

MP3 player or other audio

source to wirelessly transmit

audio to be played through the

system. Alternatively, an external

microphone can be connected.

6. CHANNEL SELECT SWITCH (CH

A/B): Use this to choose Channel

A or B. If you are using a single

microphone, we recommend using

Channel A.

7. VOLUME CONTROLS (UP -

DOWN)

8. CHARGER CONTACTS (+ -):

These contacts interface with the

charging tabs when the Redmike

VC is placed in the RMCC cradle

charger.

La page est en cours de chargement...

Lightspeed Redcat media Manuel utilisateur

Lightspeed Redcat media Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents