Creality Sermoon V1 Manuel utilisateur

Marque: Creality

Modèle: Sermoon V1

Taper: Manuel utilisateur

Ce manuel convient également à

V1.0

0101

To Our Dear Users

Instructions for Use

Thank you for choosing Creality. To make using our products easier, please read this User Manual before you start and follow the instructions provided carefully.

Creality is always ready to provide you with high-quality services. If you encounter any issues or have any questions when using our products, please use the

contact information at the end of this manual to contact us.

To further enhance your user experience, you can also use the following methods to f ind out more about using our devices:

SD card user manual: You can f ind instructions and videos in the SD card provided with your device.

You can also log in to the Creality of f icial website (www.creality.com) to f ind information regarding software and hardware, contacts, device instructions, device

warranty information, and more.

Please do not use this device with methods and operations that have not been described in this manual to avoid accidental personal injury and property damage;

Do not place the device in f lammable and explosive materials or near high heat sources. Please place the device in a ventilated and cool environment with little dust;

Do not place the printer in a vibrating or any other unstable environment. The shaking of the machine will aﬀect the printer’s printing quality;

It is recommended to use the f ilament recommended by the manufacturer to avoid damaging the device;

Do not use the power cable of other products as a replacement during the installation process. Please use the power cable provided with the machine. The power

plug needs to be plugged into a three-hole socket with a ground wire;

To prevent moving parts from pulling the human body into the device and cause cuts and lacerations, do not wear cotton gloves while operating the printer;

To avoid burns caused by overheating of the platform, after printing, please wait for the temperature of the HotBed platform to drop before removing the model;

Please maintain the device often. When the device is unplugged, use a dry cloth to clean the printer, clean up remnants in the f ilament box, and check for foreign

objects on the belt and endstop switch;

To avoid injuries, children under the age of 10 should not operate this device without adult supervision;

Do not manually move the nozzle or the heating platform quickly, otherwise, it may cause damage to the moving mechanisms or control circuit;

Users should abide by the laws and regulations of the corresponding country and region where the equipment is located (place of use), abide by professional

ethics, and pay attention to safety obligations. The use of our products or equipment for any illegal purpose is strictly prohibited. Our company is not responsible

for the relevant legal responsibilities of any violators.

0102

Table of Contents

.....................................................................................................................................................................................

.................................................................................................................................................................................................

05-14

12-15

07-11

05-05

.............................................................................................................................................................................................

03-04

.....................................................................................................................................................................................................

.................................................................................................................................................................................................

04-04

.............................................................................................................................................................................................

.......................................................................................................................................................................................

................................................................................................................................................................... 16-20

.........................................................................................................................................................................................

17-17

16-16

.........................................................................................................................................................................................

17-18

...............................................................................................................................................................................................

19-19

..........................................................................................................................................

19-19

............................................................................................................................................................

20-20

.......................................................................................................................................................................................

1. Device Description

2. Instructions for Use

3. Notes and Daily Maintenance

1.1 About the device

1.2 List of tool kit items

1.3 Device specif ications

2.1 Unboxing instructions

2.2 Local printing

2.3 Cloud printing via app

3.1 Changing f ilaments

3.2 Lubrication maintenance

3.3 Leveling the platform

3.4 Using and maintaining the magnetic adhesive sticker

3.5 Cleaning foreign objects from the chassis

3.6 Connecting to cloud print

Device Description

1.1 About the device

1.2 List of tool kit items

1. Cover

2. Front door

3. SD card slot

4. Filament entrance

Filament x1

Nozzle cleaner x1 Card reader and SD card x1 grease x1

(For lubricating the bearings)

Glue stick x1 M6 socket wrench x1

Power cable x1 Wrench and screwdriver x1 Cutting plier x1 Nozzle x1 Leveling card x1

5. Ventilation fan

6. Display screen

7. Rack

8. Power switch

9. Power socket

10. Voltage adjustment

port

(Can be used directly on the

printing platform to increase

adhesiveness and prevent

models from wrapping)

Note: The components above are for references

only. The actual product may vary.

0104

1.3 Device specif ications

Basic Parameters

Model Sermoon V1 | Sermoon V1 Pro

Modeling size 175x175x165 mm

Modeling technology FDM

Number of nozzles 1

Nozzle diameter 0.4 mm (Standard)

Accuracy ± 0.1 mm

Print materials 1.75 mm PLA / ABS / PETG

Supported slicing f ile formats STL / OBJ / AMF

Power rating 150W

HotBed temperature ≤ 80℃

Nozzle temperature ≤ 250℃

Ambient temperature 10℃ - 30℃

Power Loss Recovery Yes

Filament detection Yes

Supported slicing software Creality Slicer, Repetier-Host, Cura, Simplify3D

Printing methods Locally via SD card or cloud printing via Wi-Fi

Power speciﬁcations 100-120Vac 200-240Vac 50/60Hz

Operating systems Windows XP / Vista/ 7 / 10/ MAC / Linux

Printing speed ≤ 150 mm/s, normally between 30-60 mm/s

Open door sensor Comes standard with the Pro version

Camera Comes standard with the Pro version

0105

115V

230V

①

②

③

• Please ensure the correct position for the power supply switch and mains before supply connection, in order to avoid damage to

the device.

• If the mains between 100V and 120V, please select the 115V for the power supply switch.

• If the mains between 200V and 240V, please select the 230V for the power supply switch (default is 230V).

A. Open the device’s cover.

D. Remove the foam from the inside

of the device.

E. Check whether the moving mechanisms

are moving smoothly.

F. Note: Please ensure that the voltage matches the power

switch, otherwise the power supply may be damaged or

burnt out.

B. Use the cutting plier to cut the cable

ties around the nozzle.

C. Use the cutting plier to cut of f the cable ties on the

X-axis and Y-axis belts, and remove the cut cable

ties and foam.

2. Instructions for Use

Caution

2.1 Unboxing instructions

0106

Method 1 (Connect via Wi-Fi)

Method 2

(Connect via Bluetooth)

Insert SD card

Model slicing

Install apps

3D / STL G-code ﬁles

1. Cloud slicer

2. Cloud print

3. Cloud monitor (Pro version)

Data

Server

Connected to network

Local printing Cloud printing

0107

This manual only introduces the installation of Creality slicer software. If users use other slicer software, we recommend

to set the retraction parameter to 3mm to avoid the risk of plugging.

2.2 Local printing

2.2.1 Install slicer

1. Please login of f icial Creality website

(www.creality.com) to download the

latest Creality Slicer software.

4. Open Creality Slicer. 5. Load File

6. Select File

2. Select Preferences in sequence → Conf igure Creality

→ Next → Select corresponding language → Next →

Finish to complete the setting.

3. Select the current model.

0108

7. Generate G code → Save to memory card 8. Insert Memory Card

It is important to note f ile name within the memory card must be in Latin

letters or numbers. Chinese characters or any other special symbol

cannot be display by the printer.

Note: For details on using the software, please refer to the

slicing software user manual on the SD card.

0109

>>>>

45°

When using the printer for the ﬁrst time, please reset the printer to zero. If this procedure fails, please turn of f the power and contact after-sales.

Note: The above interface is for reference only. The actual UI may vary.

1. No foreign objects on

the printing platform

4. Load f ilament 5. Insert SD card

2. Return to zero self-test

3. Install f ilament

2.2.2 Setup wizard

0110

1. PLA mode: As our company recommends the PLA mode, the system’s parameters have

been set according to PLA f ilaments. It is recommended to use Creality f ilaments for printing.

When the inside the box temperature exceeds 30°C, please open the top cover to avoid

nozzle blockage.

2. ABS mode: As our company recommends the ABS mode, the system’s parameters have been

set according to ABS f ilaments. It is recommended to use Creality f ilaments for printing. When

printing, please ensure that the top cover is on to keep the device’s temperature inside.

Note: When printing with ABS f ilaments, it is recommended that the size of a single

model be controlled within 100 x 100 mm (length x width) to avoid warping caused by

the characteristics of the f ilaments, which can result in printing failure.

Note: Please install the f ilaments as shown in the

f igure above.

2.2.3 Printing modes

225 225

100 70.68

69 70

100 70.68

69 70

225 225

100 70.68

69 70 225 225

100 70.68

69 70

>> >>>>

0111

>> >>

2.2.4 Start printing

In this order, go to Print f iles → Select f ile → Print.

To prevent the accidental opening of the door and cause burns and mechanical injuries, please turn on the pause door opening function (this function is enabled by default).

Note: The above interface is for reference only. The actual UI may vary.

2.2.5 Automatic open door check function (Pro version only)

225 225

100 70.68

69 70

225 225

100 70.68

69 70 225 225

100 70.68

69 70 225 225

100 70.68

69 70

225 225

100 70.68

69 70 225 225

100 70.68

69 70

0112

>>>>

2.3 Cloud printing via app

2.3.1 Install app

1. Scan the QR code to download the app

2. Download 3. Create account 4. Log in

>> >> >> >>

>> >>

2.3.2 Connect to the network and cloud printing (Method 1: Connect via Wi-Fi)

As shown below, please use your smartphone to select your device model and slicing:

Note: When cloud printing via the app, be sure to uncheck the PLA mode and ABS mode on the device, otherwise the app cannot control the device temperature.

1. Add device 2. Scan the QR on the device 3. Network settings 4. Connect to device Wi-Fi

5. Connect to user Wi-Fi 6. New device added 7. Find model 8. Model slicing 9. Print via a network connection

>> >> >> >>

>> >> >>

2.3.3 Connect to the network and cloud printing (Method 2: Connect via Bluetooth)

As shown below, please use your smartphone to select your device model and slicing:

Note: When cloud printing via the app, be sure to uncheck the PLA mode and ABS mode on the device, otherwise the app cannot control the device temperature.

1. Add device

5. Connect to user Wi-Fi 6. New device added 7. Find model 8. Model slicing 9. Print via a network connection

2. Search for Bluetooth device

(Turn on Bluetooth on your smartphone)

3. Add device 4. Select user Wi-Fi

2.3.4 Cloud monitor (Pro version only)

Note: Open the camera interface on the app, and both cloud printing and local printing can be viewed remotely using the camera. The LED light will also

automatically turn on in environments with poor light.

Method 1:

Method 2:

1. Click 2. Real-time monitoring

>> >>>> >>

3. Notes and Daily Maintenance

3.1 Feed out and feed in f ilaments

Note: The above interface is for reference only. The actual UI may vary.

Once the specif ic temperature has been reached and f ilaments are withdrawing,

please immediately pull out the f ilaments. Otherwise, the f ilaments may jam up

once it has cooled down.

225 225

100 70.68

69 70 225 225

100 70.68

69 70 225 225

100 70.68

69 70

>> >> >>

010101

225 225

100 70.68

69 70

3.2 Lubrication maintenance

3.3 Leveling the platform

Note: Please perform regular maintenance on the blue area using oil and lubrication (as shown in the f igure).

Note: After using the printer for a long time, the distance between the platform and the nozzle may change, which could cause the adhesion of the f irst

layer of the model to become weak and cause a printing failure. Please level the platform regularly.

X-axis optical axis 1

Y-axis optical axis 1

Y-axis optical axis 2

Spool

Z-axis optical axis 1

Z-axis optical axis 2

X-axis optical axis 2

225 225

100 70.68

69 70 225 225

100 70.68