Dremel 3D40 FLEX Operating and Safety Instructions

1-844-4DRML3D (1-844-437-6533) www.digilab.dremel.com

P.O. Box 081126 Racine, WI 53408-1126

Operating/Safety Instructions

Consignes d’utilisation/de sécurité

Instrucciones de funcionamiento y seguridad

For English Version

See page 2

Version française

Voir page 39

Versión en español

Ver la página 76

IMPORTANT

Read Before Using

IMPORTANT

Lire avant usage

IMPORTANTE

Leer antes de usar

Call Toll Free for Consumer Information & Service Locations

Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit

Llame gratis para obtener información para el consumidor y ubicaciones de servicio

3D40 FLEX

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 1

2

Safety Symbols....................................................................................2

General Safety Warnings..................................................................3-5

Symbols ...............................................................................................5

Dremel Remote Services.....................................................................5

FCC Compliance .................................................................................6

Information on Intellectual Property .....................................................6

Specifications.......................................................................................7

Resources............................................................................................8

Glossary of Terms...........................................................................8-10

Introduction ........................................................................................10

Kit Contents .......................................................................................11

Unpacking..........................................................................................12

Getting To Know Your Dremel 3D40 FLEX...................................13-14

Initial Setup...................................................................................15-17

Touch Screen................................................................................18-24

Dremel Digilab 3D Slicer Software ....................................................24

Getting Ready to Build..................................................................25-28

Building.........................................................................................29-30

Removing Your Object .......................................................................31

Dremel Cloud Platform ......................................................................32

Best Practices....................................................................................33

Maintenance .................................................................................33-34

Troubleshooting............................................................................35-36

Firmware and Open Source Software ...............................................37

Dremel

®

Consumer Limited Warranty ................................................38

Table of Contents

Safety Symbols

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

!

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 2

3

Work Area Safety

Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

Do not operate Dremel 3D40 in the

presence of flammable liquids, gases or

dust. Dremel 3D40 creates high

temperatures which may ignite the dust or

fumes.

Store idle 3D40 out of reach of children

and other untrained persons. Injury can

occur in hands of untrained users.

Electrical Safety

Always use the Dremel 3D40 with a

properly grounded outlet. Do not modify

Dremel 3D40 plug. Improper grounding and

modified plugs increase risk of electric shock.

Do not use Dremel 3D40 in damp or wet

locations. Do not expose Dremel 3D40 to

rain. Presence of moisture increases risk of

electric shock.

Do not abuse the cord. Never use the cord

for pulling or unplugging the Dremel 3D40.

Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or

entangled cords increase the risk of electric

shock.

Avoid using this product during an

electric storm. There may be a remote risk

of a power surge from lightning that may

result in electric shock hazard.

In case of emergency unplug Dremel 3D40

from outlet.

Personal Safety

Stay alert, watch what you are doing and

use common sense when operating a

Dremel 3D40. Do not use Dremel 3D40

while you are tired or under the influence

of drugs, alcohol or medication. A moment

of inattention while operating Dremel 3D40

may result in personal injury.

Use personal protective equipment. The

use of protective equipment such as heat

resistant gloves and safety glasses will

reduce the risk of personal injuries.

Dress properly. Do not wear loose clothing

or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose

clothes, jewelry or long hair can be caught in

moving parts.

Dremel 3D40 Use and Care

Before every use check Dremel 3D40 for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the Dremel 3D40’s

operation. If damage is suspected have

the Dremel 3D40 repaired by authorized

Dremel service center before use. Use of

Dremel 3D40 when damaged may result in

poor quality of object creation, further

equipment damage, property damage or

personal injury.

Do not touch the extruder tip during

Dremel 3D40 operation or until it has

cooled down to at least 60°C (140°F).

Contact with the extruder tip during or after

operation before tip has cooled may result in

personal injury.

Set up the Dremel 3D40 in a well-ventilated

area. Place Dremel 3D40 printer on flat

nonflammable surface and away from

flammable materal. Provide at least 8

inches of unobstructed spacing around

Dremel 3D40. Dremel 3D40 melts plastic

during building. Plastic odors emitted during

Dremel 3D40 operation may irritate eyes and

airways. Locating Dremel 3D40 close to

surrounding objects prevents proper

ventilation.

Do not reach inside the Dremel 3D40 while

it is in operation. Contact with Dremel 3D40

moving parts during operation may result in

poor build quality, equipment damage or

personal injury.

Always monitor the Dremel 3D40 during

operation. Use of Dremel 3D40 by persons

unfamiliar with these warnings and

instructions may result in equipment or

property damage and personal injury.

Read all instructions in this manual and familiarize yourself with the

Dremel 3D40 before setup and use. Failure to comply with the

warnings and instructions may result in fire, equipment damage, property damage, or

personal injury.

READ ALL INSTRUCTIONS

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

General Safety Warnings

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 3

4

U

se only DREMEL filament. Use of filament

not authorized by Dremel may result in

equipment and property damage.

Ensure small objects created by Dremel

3D40 are not accessible to young children.

Small objects are potential choking hazards

for young children.

Do not create illegal or inappropriate

objects using Dremel 3D40.

Do not use Dremel 3D40 to create objects

intended for use with candles, liquid fuels,

and other heat sources. Plastic may melt

when exposed to fire or other heat sources.

Such use of objects created by Dremel 3D40

may result in fire, property damage and

personal injury.

Do not use Dremel 3D40 to create objects

intended for food or drink applications

such as preparation, decoration, storage,

or consumption. Such use of objects

created by Dremel 3D40 may result in illness

or personal injury.

Do not use Dremel 3D40 to create objects

intended with use with electrical

components or housings of electrical

components. PLA plastic is not suitable for

electrical applications. Such use of objects

created by Dremel 3D40 may result in

property damage and personal injury.

Do not put plastic objects in or around

your mouth. PLA plastic is not suitable for

food or drink preparation and food utensils.

Such use of objects created by Dremel 3D40

may result in illness or personal injury.

Do not use Dremel 3D40 to create objects

intended for chemical storage. PLA plastic

is not suitable for chemical storage. Such use

of objects created by Dremel 3D40 may result

in property damage and personal injury.

Do not modify Dremel 3D40 or alter factory

settings. Modifications may result in

equipment and property damage, and

personal injury.

Do not expose Dremel 3D40 to

temperatures exceeding 70°C (158°F).

Dremel 3D40 may become damaged. Dremel

3D40 is intended to operate in temperature

between 16-29° C (60 - 85° F).

Do not move or bump Dremel 3D40 or the

extruder during operation. The object may

build incorrectly.

Do not change filament spool unless the

building process is completed, stopped,

or paused. Changing the filament during

building will cancel the object and may

damage the extruder.

D

o not pull the filament out. Doing so may

damage the extruder.

Use extra care not to damage the extruder

tip when clearing debris. Dremel 3D40 will

not work properly with damaged extruder tip

and will require replacement.

Before every build make sure that the

flexible build plate is covered with Dremel

specified build tape. Use of improper build

tape may result in equipment damage and

poor object build quality.

Do not flex the build plate with the object

pointing towards yourself and others.

Objects flying off the build plate may result in

personal injury.

Be aware of your body position when

using hand tools to remove objects from

the flexible build plate. Sudden tool slip and

improper body position during object removal

from the flexible build plate may result in

personal injury.

Avoid scratching the build plate when

removing objects. Scratches in the build

plate will result in improper object creation.

Do not drop the build plate holder.

Tempered glass plate may break and result in

personal injury.

Do not remove tempered glass plate from

plastic holder. Contact with tempered glass

plate edge may result in personal injury.

Do not twist or bend the build plate holder

while removing objects. Tempered glass

plate may separate from plastic holder and

result in personal injury.

Dremel is not responsible for structural

integrity or utility of objects created using

Dremel 3D40. Structural models created by

inexperienced designers may result in

property damage and personal injury.

Keep the build plate holder away from

cardiac pacemakers. The magnets of the

build plate holder generate a field that can

impair the function of cardiac pacemakers.

Keep the build plate holder away from

magnetic data medium and magnetically-

sensitive equipment. The effect of the

magnets of the build plate holder can lead to

irreversible data loss.

Service

Always unplug Dremel 3D40 from its

power before performing any service

procedures. Failure to do so may result in

personal injury and equipment damage.

Have your Dremel 3D40 serviced only by

an authorized Dremel service center using

only Dremel replacement parts. This will

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 4

5

Dremel remote services provide you with

information and services regarding your Dremel

3D products. The type of information provided

by Dremel remote services may change from

time to time. All product information and

services are provided for your convenience, “As

is” and “As Available”.

Dremel does not guarantee that the information

or services will be available, accurate, or

reliable, or that product information or services

will provide safety in your home. You use all

product information, services, and products at

your discretion and risk. The product

information and services are not intended as a

substitute for direct means of obtaining

information.

Network connectivity requires an access point

and high speed internet connection. Internet

service provider charges may apply.

Mobile printing requires a compatible mobile

device and data plan. Carrier charges may

apply.

Dremel Remote Services

Symbols

IMPORTANT: Some of the following symbols may be used on your 3D40. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

Symbol Designation / Explanation

V Volts (voltage)

A Amperes (current)

Hz Hertz (frequency, cycles per second)

ø

Diameter

0 Off position

Alternating current (type or a characteristic of current)

Hot surface hazard symbol. Contact may cause burn. Allow to cool before

servicing.

Alerts user to read manual.

This symbol designates that this tool is listed by Underwriters Laboratories,

to United States and Canadian Standards.

The magnets of the build plate holder generate a field that can impair the

function of cardiac pacemakers.

e

nsure that proper operation and safety of

Dremel 3D40 is maintained.

Use only Dremel approved components.

Use of components other than genuine

Dremel components may void warranty.

U

se only Dremel approved filament.

Damage to the product resulting from use of

filament other than Dremel approved filament

is not covered under warranty.

SAVE THESE INSTRUCTIONS

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 5

6

FCC COMPLIANCE

NOTE: This equipment has been tested and

found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct

the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

Changes and Modifications not expressly

approved by the manufacturer or registrant of

this equipment can void your authority to

operate this equipment under Federal

Communications Commission’s rules.

FCC Compliance

Information on Intellectual Property

The Dremel 3D40 is intended for 3D printing

objects from digital files that you create or

own, or have the right to print using the

Dremel 3D40. When making objects using

the Dremel 3D40, it is your responsibility to

ensure that you do not infringe any third

party intellectual property rights or violate

any applicable laws or regulations, such as

U.S. or foreign intellectual property laws.

The Dremel 3D40 may not be used to make

objects protected by intellectual property

rights owned by third parties without such

third parties’ permission. Using the Dremel

3D40 to do any of the following may require

the permission of third parties: to make a

duplicate or facsimile (in whole or in part) of

any object not created by you, to make an

object from a digital file you do not own, or to

make an object from a scan of a physical

object that you did not create. It is your

responsibility to obtain such permission. In

some cases, you may not be able to obtain

such permission. Where such permission

cannot be obtained, you should not 3D print

such object, or you do so at your own risk.

You may not modify, reverse engineer,

decompile, or disassemble the Dremel 3D40

or its software or firmware, except as

permitted by applicable law.

If you use the Dremel 3D40 in any way other

than as recommended and described in

these Operating/Safety Instructions, you do

so at your own risk. Using the Dremel 3D40

to make objects that infringe any intellectual

property rights owned by third parties could

result in civil or criminal prosecution and

penalties, and you could be liable for money

damages, fines, or imprisonment.

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 6

7

Specifications

BUILDING

Extruder: Single extrusion

Extruder temperature: Up to 230°C (397° F)

Operating Interface: 3.5” full color IPS touch

screen

Maximum Build Volume: 10” x 6” x 6.7”

(255 mm x 155 mm x 170 mm)

Layer Thickness: 50 microns (0.05 mm)

Filament Colors: For color choices see

www.digilab.dremel.com

Internal Storage: 4 GB

External Storage: USB Flash Drive

WEIGHT & DIMENSIONS

Weight (without spool): 16 kg (35 lbs)

Dimensions: 20.25” x 16” x 15.9”

(515 mm x 406 mm x 394 mm)

FILAMENT

ONLY works with Dremel 1.75 mm filament

FILAMENT STORAGE

All polymers degrade with time. Do not

unpack until filament is needed. Filament

should be stored at room temperature:

16-29° C (60-85° F) and in dry conditions.

SOFTWARE

Dremel 3D40 comes with complimentary

Dremel Digilab 3D Slicer software for

Windows and Mac OSX. This application

converts your 3D digital files into buildable

files.

SUPPORTED OPERATING SYSTEMS

• Apple

®

Mac

®

OS

®

X v10.9 or later

(Mavericks)

• Microsoft

®

Windows

®

8.1

• Microsoft

®

Windows

®

7 SP1

MINIMUM SYSTEM SPECIFICATIONS

• CPU: 64-bit processor (32-bit not

supported)

• Memory: 3 GB RAM (4 GB or more

recommended)

• Disk space: ~2 GB free disk space for

installation

• Display card: 1,024 MB GDDR RAM or

more. Microsoft

®

Direct3D

®

11 capable

graphics card or higher

• Pointing device: Three-button mouse

ELECTRICAL REQUIREMENTS

3D40 input rating: 100-240V, 47-60Hz,

0.8A-1.8A

OPERATING ENVIRONMENT

Room Temperature: 16-29° C (60 - 85° F)

Level workspace

Dry workspace environment

16” (406mm)

20.25” (515mm) 15.5” (394mm)

WALL

8” (203mm)

8” (203mm)8” (203mm)

14” (356mm)

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 7

8

Glossary of Terms

Resources

Resource Description Location

Quick Start

Guide

Provides illustrated walkthrough of

how to un-box your 3D40.

Printed version of the Quick Start

Guide is located in the rectangular

component carton. It is also

available on

www.digilab.dremel.com

Dremel 3D

Website

Provides the latest 3D40 software,

product information, customer support,

and 3D model and project downloads.

www.digilab.dremel.com

Dremel 3D

Customer

Support

Contact Dremel for product support,

maintenance, and service.

1-844-4DRML3D

(1-844-437-6533)

www.digilab.dremel.com

Dremel Digilab

3D Slicer

Software

Allows you to upload, edit, and build

3D files.

Installed from

www.digilab.dremel.com or from

USB flash drive provided with the

Dremel 3D40.

Term Definition

Flexible Build Plate The flat, flexible surface used by your Dremel 3D40 to build objects. The flexible build

plate is comprised of a flexible steel plate with plastic handles for easy bending. The

flexible build plate is attached to the printer using the build plate holder.

Build Plate Holder The flat, magnetic surface used to hold the flexible build plate. It has a magnetic surface,

two notches in the back and two movable latches in the front to hold down the flexible

build plate.

Build Platform Clip Clip located at the front of the build platform base that is used to secure the build plate in

place.

Build Tape Adhesive tape that improves the consistency of your objects and helps them stick to the

build plate surface.

Build Volume The three dimensional (3D) amount of space that an object will use once it is completed.

Your Dremel 3D40 has a maximum build volume which means that objects with a larger

build volume cannot be built unless they are resized or broken into sub-objects.

Door Your Dremel 3D40 has a door located on the front panel. This allows for easy access to

the build plate, extruder, filament, and your objects. This door is made with a transparent

material so you can monitor the progress of your objects while keeping the build

environment stable.

Ethernet Port A local area wired networking technology that allow electronic devices to communicate.

Extruder An assembly that uses gears to pull filament through the extruder intake, heat the filament

to the build temperature, and push the heated filament out of the extruder tip.

Extruder Fan A fan used to cool the outer assembly of the extruder and gear motor.

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 8

9

Extruder Fan Baffle A plastic piece that directs air from the extruder fan onto the build plate to assist in

cooling the active build.

Extruder Intake An opening located at the top of the extruder where filament is inserted for building.

Extruder Lever A lever located on the side of the extruder that is used to loosen the grip of the

extruder gear motor.

Extruder Tip A nozzle located at the bottom of the extruder where heated filament is forced out for

building.

Filament A threadlike strand of plastic material.

Filament Guide Tube A plastic piece that guides the filament from the filament spool through a passage in

the outer housing of your Dremel 3D40.

Filament Jam Sensor A sensor in the extruder that pauses your printer if filament stops extruding properly.

Filament Runout Sensor A sensor in the extruder intake that pauses your printer if it runs out of filament

during a build.

Filament Spool A cylindrical piece on which a long strand of filament is wound for storage and

continuous use.

.g, .gcode, .g3drem A buildable file format compatible with your Dremel 3D40.

Leveling Knobs Knobs located under the build platform base that are used to create proper spacing

between the extruder tip and the build plate.

Leveling Sensor A sensor that detects the height of the build platform and assists in proper leveling.

Lid Your Dremel 3D40 has a pivoting lid on the top. This allows for more access to the

build plate, extruder, filament, and objects when necessary.

Needle Nose Pliers Common tool used to hold small objects and to grab excess material that may be too

hot to touch directly.

OBJ File A common digital file format used in a wide range of 3D model software. This file is

created in 3rd party 3D software or downloaded.

Object Removal Tool A tool used to separate your objects from the build plate.

PLA A bioplastic derived from renewable resources such as corn starch.

Spool Holder A plastic piece located to the left of the build plate inside your Dremel 3D40 build area

that is designed to hold a filament spool.

Spool Door A removable door which locks the filament spool to the spool holder.

Stepper Motor A brushless DC electric motor used to drive the guide rails and extruder gears.

.STL File A common digital file format used in a wide range of 3D model software. This file is

created in 3rd party 3D software or downloaded.

Touch Screen Full color display that is touch activated. It allows you to monitor your Dremel 3D40

and objects while also providing commands directly to your Dremel 3D40 without the

use of a computer.

USB Flash Drive A portable memory card used on a wide array of devices.

Glossary of Terms

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 9

10

Introduction

Welcome to the world of Dremel Digilab. Our

mission is to mentor you through the 3D

building process and share best practices for

bringing your ideas to life.

3D building is a process that will involve

experimentation and persistence. Thankfully,

the Dremel experts are here to make your

job easier with online tips and live support.

Dremel 3D40 brings new functionality to

Dremel3D such as network connectivity and

remote printing. To get started with 3D40

follow the initial setup routine on the touch

screen.

You can create a user profile by going to

www.digilab.dremel.com. Your profile gives

you access to high-quality models, support

and software downloads, and remote printing

services. Once setup and registration is

complete you are ready to start building.

WIFI A local area wireless networking technology that allow electronic devices to

communicate.

X-Axis Guide Rails A set of rails on either side of the extruder that allow a stepper motor to move the

extruder to the left or right side of the build area.

Y-Axis Guide Rails A set of rails on either side of the build area that allow a stepper motor to move the

extruder to the front or back of the build area.

Z-Axis Guide Rails A set of rails located at the back of the build area that allow a stepper motor to move

the build plate up or down.

Glossary of Terms

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 10

11

Kit Contents*

1-844-4DRML3D (1-844-437-6533) www.dremel.com

P.O. Box 081126 Racine, WI 53408-1126

Operating/ Safety Instructions

C

onsignes d’utilisation/de sécurité

Instrucciones de funcionamiento y seguridad

For English Version

S

ee page 2

Version française

V

oir page 40

Versión en español

V

er la página 78

I

MPORTANT

Read Before Using

I

MPORTANT

Lire avant usage

I

MPORTANTE

Leer antes de usar

C

all Toll Free for Consumer Information & Service Locations

Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit

Llame gratis para obtener información para el consumidor y ubicaciones de servicio

3D40 FLEX

3D40 Quick Start Guide

WARNINGWARNING

R

EAD ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE

DREMEL 3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS

MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.

Dremel 3D40 Instruction Manual Quick Start Guide

Filament Spool** Power Cable USB Cable

Build Tape Object Removal Tool USB Flash Drive

Flexible Build Plate and

Build Plate Holder

Unclog Tool

*Quantities may vary depending on kit. **Do not store in moist or hot environment.

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 11

12

1. Place box on table, cut tape, and open.

2. Remove top insert.

3. Remove 3D40 and place on table.

4. Open lid and remove top insert.

5. Raise build platform by lifting from both sides.

6. Open door and remove middle insert.

7. Remove bottom insert.

Tip: Keep packaging for future transportation

and storage.

Unpacking

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 12

13

Getting To Know Your 3D40 FLEX

1. Lid

2. Extruder

3. Z-Axis Guide rail

4. Door

5. Gripping Handles

6. USB A Port

7. Leveling Knobs

8. Build Platform Clip

9. Touch Screen

10. Build Plate Holder

11. Flexible Build Plate

12. Filament Spool Holder

13. Filament Spool

14. Y-Axis Guide Rail

15. Stepper motor

16. Filament Guide Tube

17. Extruder Lever

18. Filament Guide Clip

19. Extruder Intake

20. Extruder Fan

21. Ribbon Cable

22. X-Axis Guide Rail

23. Leveling Sensor

24. Extruder Tip

25. Power Switch

26. USB B Port

27. Ethernet Port

28. Nameplate

29. Power Input

1

4

9

6

13

10

2

12

5

8

7

3

11

FIG. 1

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 13

14

M

o

d

e

l

3

D

4

0

F

0

1

3

D

4

0

1

0

V

–

2

4

0

V

~

4

7

–

6

3

H

z

0

.

8

–

1

.

8

A

Ø

1

.

7

5

m

(

0

.

0

6

9

"

)

L

I

S

T

E

D

3

D

P

R

I

N

T

E

R

E

4

6

9

3

1

U

1

S

N

K

O

N

I

J

N

E

N

B

E

R

G

6

0

,

4

8

2

5

B

D

B

R

E

D

A

-

N

L

M

/

Y

X

D

r

e

m

e

l

M

o

u

n

t

P

r

o

s

p

e

c

t

,

I

L

M

a

d

e

i

n

C

h

i

n

a

15 16 17 21

22

24

25 26 27 29

23

20

28

14

18

19

Getting To Know Your 3D40 FLEX

FIG. 2

FIG. 3

FIG. 4

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 14

B

A

15

PREPARING BUILD PLATE

Do not drop the build

plate. Tempered glass

plate may break and result in personal injury.

Do not remove

tempered glass plate

from plastic holder. Contacting with

tempered glass plate edge may result in

personal injury.

Before every build make

sure that the flexible

build plate is covered with Dremel specified

build tape. Use of improper build tape may

result in equipment damage and poor object

build quality.

1. Your build plate consists of two parts: the

flexible build plate, and the build plate

holder. The build plate holder has a

magnetic surface to attach the flexible

build plate to, and it has two notches in

the back and movable latches in the front

to hold down the corners of the flexible

build plate.

2. The flexible build plate can be removed

from the build plate holder by rotating the

movable latches towards you (A), lifting

the flexible build plate up by the blue

handles (B), and pulling it out towards you

(C), figure 5.

3. The flexible build plate comes with build

tape installed. To remove it, lift it up from

the tab at the front corner and slowly peel

off. To install a new build tape, remove

adhesive liner from build tape and place

build tape over flexible build plate. For

best results, apply build tape at center of

flexible build plate and smooth outward to

remove any air bubbles, figure 6.

Build

Tape

Flexible

Build

FIG. 6

FIG. 5

Initial Setup

Flexible Build

Plate

Build Plate

Holder

Latches

Handle

Notch

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 15

16

Initial Setup

4. The flexible build plate can be installed on

top of the build plate holder by sliding it

backwards at an angle so that the corners

of the flexible build plate slide under the

notches at the back of the build plate

holder. Release the flexible build plate so

it sticks on top of the magnet, and close

the latches at the front to hold it in place.

TIP: It is much easier to remove and

install the flexible build plate if the build

plate holder is already installed in the

printer. In general, once the build plate

holder is installed in the printer you do not

need to remove it, you only need to

remove the flexible build plate.

5. The build plate holder can be removed by

pinching the clip located at the front of the

build platform and lifting the build plate

holder off the base, figure 7.

6. Install the build plate holder using the build

platform clips.

P

R

E

S

L

I

F

T

FIG. 7

Clip

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 16

17

Initial Setup

The first time you power on your Dremel

3D40 you will be prompted to setup your

printer, connect to a network, update your

firmware and create an online account.

Completing this process will give you access

to features such as printing wirelessly, printer

sharing amongst your friends and family,

notifications of firmware updates, and printer

status monitoring. You will then be walked

through how to loading your first roll of

filament and how to properly level the build

plate.

1. Select your country and your language.

2. To complete initial setup, tap “Yes” when

prompted on the initial setup screen. If you

decline this setup you can always setup

network and register later.

3. If you choose “Yes”, 3D40 will

automatically connect to your ethernet (if

plugged into router skip to step 5) or

search for available wireless networks.

4. Choose your wireless network using the

touch screen. Use the arrows to scroll

through the list of available wireless

networks. When your wireless network

name is highlighted, tap “Accept”.

5. Enter your wireless network password and

tap “Accept”.

6. Tap "Yes" to update your firmware (if a

firmware update is available) to get the

latest features and improvements.

7. Tap “Done” to complete the initial setup

process on your printer.

8. Visit digilab.dremel.com/getstarted and

follow the prompts to complete your user

profile creation and 3D40 registration.

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 17

18

Touch Screen

Using your Dremel 3D40 without a computer is easy with the onboard software and full color

touch screen.

Before building your model we want to familiarize you with the touch screen menu structure

and options.

Observe all provided warnings and safety instructions when using

the Dremel 3D40. Failure to do so may result in fire, equipment damage,

property damage or personal injury.

BUILD

Tap to select a 3D model and begin build process.

(see page 28 for detailed build instructions)

BUILD MENU

Tap Printer, USB Flash Drive, or Print Queue to

choose the destination of your desired file.

MODEL MENU

Tap to select the desired model or use arrows to

scroll through pages to find your model.

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 18

19

FILE DETAILS

BUILD – Tap to begin build process.

DELETE – Tap to remove model file from on-printer

storage or USB flash drive.

COPY TO PRINTER – From USB flash drive, tap to

copy model file to on-printer storage.

BUILD STATUS

STOP – Tap to cancel the current build process.

PAUSE/PLAY – Tap to pause or resume the current

build process. Pause will allow you to access the

filament button.

CHANGE FILAMENT – Tap to change filament

during the current build process to add more

filament or change colors.

PRINT QUEUE MENU

BUILD – Tap to view details of next build.

DELETE – Tap to remove next build from queue.

PRINT QUEUE MODEL DETAILS

BUILD – Tap to begin build process.

DELETE – Tap to remove model file from queue.

Touch Screen

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 19

20

FILAMENT

Tap to begin heating and start filament load/change

process. (See page 25 for instructions on filament

load/change process)

LEVEL

Tap to begin build plate leveling process. (see page

27 for instructions on leveling the build plate)

Touch Screen

DM 2610039151 10-18.qxp_3D40 10/8/18 10:34 AM Page 20

La page charge ...

Dremel 3D40 FLEX Operating and Safety Instructions

Dremel 3D40 FLEX Operating and Safety Instructions

dans d''autres langues

Documents connexes

Autres documents