Klein Tools CL700 Manuel utilisateur

INSTRUCTION MANUAL

ENGLISH

FRANÇAIS pg. 33

ESPAÑOL pg. 17

600A AC Auto-Ranging

Digital Clamp Meter

1000V

600A

60M

Ω

True RMS

Measurement

Technology

600A AC Auto-Ranging

Digital Clamp Meter

True RMS

Measurement

Technology

• NON-CONTACT

VOLTAGE METER

• LOW IMPEDANCE

• DATA & RANGE

HOLD

• AUDIBLE CONTINUITY

• DIODE TEST

• CAPACITANCE &

FREQUENCY

CL700

2m

-14° –

1000°F

(-26° –

538°C)

IP40

5000573

CAT IV

600V

CAT III

1000V

2

GENERAL SPECIFICATIONS

Klein Tools CL700 is an automatically ranging true root mean square

(TRMS) digital clamp-meter that measures AC current via the clamp,

and measures AC/DC voltage, resistance, continuity, frequency,

capacitance, and tests diodes via test-leads, and temperature via a

thermocouple probe. It also features a Low Impedance (LoZ) mode

for identifying and eliminating ghost or stray voltages.

• Operating Altitude: 6562 ft. (2000m)

• Relative Humidity: <80% non-condensing

• Operating Temp: 32° to 104°F (0° to 40°C)

• Storage Temp: 14° to 140°F (-10° to 60°C)

• Accuracy: Values stated at 65° to 83°F (18° to 28°C)

• Temp Coefcient: 0.1 x (Quoted Accuracy) per °C above

28°C or below 18°C, corrections are required when ambient

working temp is outside of Accuracy Temp range

• Dimensions: 9.09" x 3.82" x 1.54" (231 x 97 x 39 mm)

• Weight: 11.8 oz. (335 g) including batteries

• Calibration: Accurate for one year

• Standards: Conforms to: UL STD 61010-1, 61010-2-032,

61010-2-033.

Certified to: CSA STD C22.2 # 61010-1,

61010-2-032, 61010-2-033.

IEC EN 61010-1, 61010-2-032,

61010-2-033, 61326-1.

• Pollution degree: 2

• Accuracy: ± (% of reading + # of least significant digits)

• Drop Protection: 6.6 ft. (2m)

• Safety Rating: CAT IV 600V, CAT III 1000V, Class 2,

Double insulation

CAT III: Measurement category III is applicable to test and

measuring circuits connected to the distribution part of the

building’s low-voltage MAINS installation.

CAT IV: Measurement category IV is applicable to test and

measuring circuits connected at the source of the building’s

low-voltage MAINS installation.

• Electromagnetic Environment: IEC EN 61326-1. This

equipment meets requirements for use in basic and controlled

electromagnetic environments like residential properties,

business premises, and light-industrial locations.

Specifications subject to change.

ENGLISH

3

ELECTRICAL SPECIFICATIONS

Function Range Resolution Accuracy (50/60 Hz)

AC Voltage

(V AC)

6.000V 1mV ±(1.5% + 5 digits)

60.00V 10mV ±(1.2% + 5 digits)

600.0V 100mV

1000V 1V ±(1.5% + 5 digits)

DC Voltage

(V DC)

600mV 0.1mV ±(1.0% + 8 digits)

6.000V 1mV

±(1.0% + 3 digits)60.00V 10mV

600.0V 100mV

1000V 1V ±(1.2% + 3 digits)

Input Impedance: 10MΩ Frequency Range: 50 to 400Hz

Maximum Input: 1000V AC RMS or 1000V DC

AC Current

(A AC)

60.00A 10mA ±(2.0% + 8 digits)

600.0A 100mA ±(2.0% + 5 digits)

Frequency Range: 50 to 60Hz

Function Range Resolution Accuracy

Resistance

600.0Ω 0.1Ω

±(1.5% + 5 digits)

6.000KΩ 1Ω

60.00kΩ 10Ω

600.0kΩ 100Ω

6.000MΩ 1kΩ

60.00MΩ 10kΩ ±(2.0% + 10 digits)

Maximum Input: 600V AC RMS or 600V DC

Capacitance

60.00nF 0.010nF ±(5.0% + 35 digits)

600.0nF 0.1nF

±(3.0% + 5 digits)6.000µF 0.001µF

60.00µF 0.01µF

600.0µF 0.1µF ±(5.0% + 5 digits)

6000µF 1µF

Maximum Input: 600V AC RMS or 600V DC

Temperature

(Fahrenheit)

-14° to 32°F

0.1 to 1

°F

±(2.0% + 9

°F

)

33° to 752°F

±(1.0% + 5.4

°F

)

753° to 1000°F

±(2.0% + 9

°F

)

Temperature

(Celsius)

-26° to 0°C

0.1 to 1

°C

±(2.0% + 5

°C

)

1° to 400°C

±(1.0% + 3

°C

)

401° to 538°C

±(2.0% + 5

°C

)

4

ENGLISH

ELECTRICAL SPECIFICATIONS

FREQUENCY (AUTO-RANGING)

9.999Hz 0.001Hz

±(1.0% + 5 digits)

99.99Hz 0.01Hz

999.9Hz 0.1Hz

9.999kHz 1Hz

99.99kHz 10Hz

500.00kHz 100Hz

Sensitivity: >8V RMS

Maximum Input: 600V DC or 600V AC RMS

DUTY CYCLE

1% to 99.9%

0.1% ±(1.2% + 2 digits)

Pulse width: 0.1 – 100ms

Frequency width: 5Hz to 10kHz

Sensitivity: >8V RMS

Maximum Input: 600V DC or 600V AC RMS

OTHER MEASUREMENT APPLICATIONS

Maximum Input: 600V AC RMS or 600V DC

• Diode Test: Max. 1.5mA, open circuit voltage ~3.0V DC

• Continuity Check: Audible signal <50Ω, test current <0.35mA

• Sampling Frequency: 3 samples per second

• Low Impedence (Low Z): Input impedence >3kΩ

Max input 600V RMS

• Auto Power off: After ~30 minutes of inactivity

• Overload:

"OL" indicated on display, overload protection

1000V in Voltage setting, 600V RMS in all other settings

• Polarity: "-" on display indicates negative polarity

• Display: 3-5/6 digit, 6000 Count LCD

5

WARNINGS - GENERAL

To ensure safe operation and service of the meter, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

• Before each use verify meter operation by measuring a known voltage

or current.

• Never use the meter on a circuit with voltages that exceed the category

based rating of this meter.

• Do not use the meter during electrical storms or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Probe assemblies to be used for MAINS measurements shall meet IEC/EN

61010-031 with a voltage RATING of CAT IV 600V or better.

• Ensure meter leads are fully seated, and keep fingers away from the

metal probe contacts when making measurements.

• Use caution when working with voltages above 25V AC RMS or 60V DC.

Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock, replace batteries

when a low battery indicator appears.

• Do not attempt to measure resistance or continuity on a live circuit.

• Always adhere to local and national safety codes. Use personal protective

equipment to prevent shock and arc blast injury where hazardous live

conductors are exposed.

• To avoid risk of electric shock, disconnect leads from any voltage source

before removing battery door.

• To avoid risk of electric shock, do not operate meter while battery door is removed.

WARNINGS - NCV FUNCTION

• When NCV Function is initiated, a blinking or steady red glow and an audible

beep indicate voltage present. If no indication, voltage could still be present.

• Before and after each use of the NCVT, verify operation by testing a known

working circuit that is within the rating of this unit.

• Never assume neutral or ground wires are de-energized. Neutrals in multi-wire

branch circuits may be energized when disconnected and must be retested

before handling.

• The NCV tester WILL NOT detect voltage if:

• The wire is shielded.

• The

operator is not grounded or is otherwise isolated from an effective earth ground.

• The voltage is DC.

• The NCV tester MAY NOT detect voltage if:

• The user is not holding the tester.

• The user is insulated from the tester with a glove or other materials.

• The wire is partially buried or in a grounded metal conduit.

• The tester is at a distance from the voltage source.

• The field created by the voltage source is blocked, dampened, or otherwise

interfered with.

• The frequency of the voltage is not a perfect sine wave between 50 and 60Hz.

• The tester is outside of operation conditions (listed in Specifications section).

• Operation may be affected by differences in socket design and insulation

thickness and type; tester may not be compatible with some types of standard

or tamper resistant (TR) electrical outlets.

• Do not apply to uninsulated hazardous live conductors.

• Detection above 50V is specified under “normal” conditions as specified below.

The tester may detect at a different threshold at different conditions, or may not

detect at all unless:

• The

tip of the tester is within 0.25" of an AC voltage source radiating unimpeded.

• The user is holding the body of the tester with his or her bare hand.

• The user is standing on or connected to earth ground.

• The air humidity is nominal (50% relative humidity).

• The tester is held still.

6

ENGLISH

SYMBOLS ON METER

AC

AC/DC

Resistance (in Ohms) Audible Continuity

Double Insulated Class II Ground

Diode Capacitance

Hz

Frequency

%

Duty-cycle

°

F/

°

C

Temperature (Fahrenheit / Celsius)

Low Impedance

V Voltage (Volts) A Amperage (Amps)

Warning or Caution

To ensure safe operation and service of this meter, follow all

warnings and instructions detailed in this manual.

Risk of Electrical Shock

Suitable for uninsulated hazardous live conductors

SYMBOLS ON LCD

AC Measurement

DC Measurement

Negative Reading Data Hold

Auto Ranging MAX Maximum Value Hold

MIN Minimum Value Hold Low Battery

Auto Power Off Audible Continuity

Diode Test

k

kilo (value x 10

3

)

M

Mega (value x 10

6

)

m

mili (value x 10

-3

)

μ

micro (value x 10

-6

)

n

nano (value x 10

-9

)

Ohms

V

Volts

A

Amps

F

Farads

Hz

Frequency (Hertz)

%

Duty Cycle

°

F

Degrees (Fahrenheit)

°

C

Degrees (Celsius)

7

FEATURE DETAILS

1. 6000 count LCD display 8. "MAX/MIN" button

2. Function selector switch 9.

"SEL" (select) button

3. Clamp 10.

Clamp trigger (press to open clamp)

4. "COM" jack 11. Arrow markings

5. "VΩ" jack 12. N

on-contact Voltage Testing Button

6. Data Hold / Backlight button 13. Test lead holder for test probe

7. "RANGE" button 14.

Non-Contact Voltage Testing Sensor

FEATURE DETAILS

1

9

2

3

10

13

14

12

5

8

7

4

6

NOTE: There are no user-serviceable parts inside meter.

11

8

ENGLISH

FUNCTION BUTTONS

ON/OFF

To power ON the meter, rotate the Function Selector switch

2

from

the OFF setting to any measurement setting. To power OFF the meter,

rotate the Function Selector switch

2

to the OFF setting. By default,

the meter will automatically power OFF after 30 minutes of inactivity.

If the meter automatically powers OFF while in a measurement

setting, rotate Function Selector switch

2

to any other setting

(excluding the OFF setting) to power ON the meter. To deactivate

the power OFF functionality press and hold the "SEL" button

9

before powering ON from the OFF setting. When auto power OFF

is deactivated, the Auto Power Off icon will not be visible in the

display.

"SEL" (SELECT) BUTTON (FOR SECONDARY FUNCTIONS)

The "SEL" button

9

activates the secondary function for each

application accessible by the function selector switch

2

. For

voltage and low impedance it toggles between AC and DC, for the

other functions it switches between °F and °C, between Hz and %

Duty-Cycle, and between Continuity, Resistance, and Diode-Test. The

default function for each application is printed on the meter in white;

the secondary function or functions for each setting is printed on the

meter in orange.

DATA HOLD

Press the Data Hold / Backlight button

6

to hold the measurement

on the display. Press again to release the display to return to live

measuring.

BACKLIGHT

Press and hold the Data Hold / Backlight button

6

for more than

one second to turn ON the backlight. The backlight will automatically

power OFF after 3 minutes of inactivity.

RANGE

The meter defaults to auto-ranging mode . This mode

automatically determines the most appropriate measurement range

for the testing that is being conducted. To manually force the meter to

measure in a different range, use the Range button

7

.

1. Press the "RANGE" button

7

to manually select measurement

range ( is deactivated on the LCD). Repeatedly press the

"RANGE" button

7

to cycle through the available ranges, stopping

once the desired range is reached.

2. To return to auto-ranging mode, press and hold the "RANGE"

button

7

for more than one second ( is reactivated).

9

FUNCTION BUTTONS

MAX/MIN

When the "MAX/MIN" button

8

is pressed, the meter keeps track

of the Maximum and Minimum values and the difference between

the Maximum and Minimum values as the meter continues to take

samples.

1. When measuring, press "MAX/MIN" button

8

to toggle between

the Maximum value (MAX) and the Minimum value (MIN). If a

new Maximum or Minimum occurs, the display will update with

the new value.

2. Press "MAX/MIN" button

8

for more than one second to return to

normal measuring mode.

NON-CONTACT VOLTAGE TESTING

Press the NCV button

12

to test for AC voltage using the integrated

non-contact voltage meter. Approach the conductor under test

leading with the sensing antenna

14

. The meter delivers visual

warning signals when AC voltage is detected.

TEST LEAD HOLDER

When working with test leads, one test probe may be mounted in the

test lead holder

13

to facilitate natural two-handed operation with the

clamp in one hand and a single test probe in the other.

10

ENGLISH

OPERATING INSTRUCTIONS

CONNECTING TEST LEADS

Do not test if leads are improperly seated. Results could cause

intermittent display readings. To ensure proper connection, firmly

press leads into the input jack completely.

TESTING IN CAT III / CAT IV MEASUREMENT LOCATIONS

Ensure the test lead shield is pressed firmly in place. Failure to use

the CATIII / CATIV shield increases arc-flash risk.

TESTING IN CAT II MEASUREMENT LOCATIONS

CAT III / CAT IV shields may be removed for CAT II locations. This

will allow testing on recessed conductors such as standard wall

outlets. Take care not to lose the shields.

INCORRECT

CORRECT

0.7" (18 mm)

5/32"

(4 mm)

5/32

(4 mm)

11

OPERATING INSTRUCTIONS

AC CURRENT (LESS THAN 600A)

AC Current is measured by pressing the clamp trigger

10

to open

the clamp

3

and placing it around a current-carrying wire. When

measuring, care should be taken to ensure that the clamp

3

is

completely closed with trigger

10

fully released, and that the wire

passes perpendicularly through the center of the clamp

3

in line

with the arrow markings

11

.

NOTE: Current measurement can be made by clamping around

single conductors, but not cables containing both live and neutral

wires. In this case a line splitter is required, Klein Cat. No. 69409 is

recommended.

To measure current:

1. Rotate the Function Selector switch

2

to the AC current A setting.

2. Place clamp

3

around wire. The current measurement will be

shown in the display.

The meter will auto-range to display the

measurement in the most appropriate range.

Disconnect test leads when measuring with the clamp.

HOT WIRE

GROUND WIRE

LIVE

CABLE

NEUTRAL WIRE

12

OPERATING INSTRUCTIONS

AC/DC VOLTAGE (LESS THAN 1000V)

Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

AC/DC voltage V setting.

The meter defaults to AC measurement.

To measure DC, press the "SEL" button

9

to toggle between AC

and DC modes. The AC or DC icon on the LCD indicates which

mode is selected. Note or on the display.

1. Apply test leads to the circuit to be tested to measure voltage.

The meter will auto-range to display the measurement in the

most appropriate range.

NOTE: If "–" appears on the LCD, the test leads are being applied to

the circuit in reverse. Swap the position of the leads to correct this.

NOTE: When in a voltage setting and the test leads are open,

readings of order mV may appear on the display. This is noise and

is normal. By touching the test leads together to close the circuit

the meter will measure zero volts.

AC/DC LoZ VOLTAGE (LESS THAN 600V)

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the AC/DC

LoZ voltage setting. The meter defaults to AC measurement. To

measure DC, press the "SEL" button

9

to toggle between AC and

DC modes. The AC or DC icon on the LCD indicates which mode is

selected. Note Note or on the display.

2. Apply test leads to the circuit to be tested to measure voltage.

The meter will auto-range to display the measurement in the

most appropriate range.

Do not attempt to measure voltages greater than 600V

in LoZ setting.

ENGLISH

Black lead Red lead

13

RESISTANCE MEASUREMENTS

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Continuity/Resistance/Diode-Test setting.

NOTE: The meter defaults to Continuity testing in this mode. Press

the "SEL" button

9

once to enter Resistance testing mode. The

Resistance icon will appear on the display.

2. Remove power from circuit.

3. Measure resistance by connecting test leads to circuit. The

meter will auto-range to display the measurement in the most

appropriate range.

NOTE: When in a Resistance setting and the test leads are open

(not connected across a resistor), or when a failed resistor is under

test, the display will indicate O.L. This is normal.

DO NOT attempt to measure resistance on a live circuit.

CONTINUITY

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Continuity/Resistance/Diode-Test setting.

NOTE: The meter defaults to Continuity testing in this mode. Ensure

that the Continuity Testing icon is visible on the display. If not,

press the "SEL" button

9

repeatedly until the icon is shown.

2. Remove power from circuit.

3. Test for continuity by connecting conductor or circuit with test

leads. If resistance is measured less than 50Ω, an audible signal

will sound and display will show a resistance value indicating

continuity. If circuit is open, display will show "OL".

DO NOT attempt to measure continuity on a live circuit.

OPERATING INSTRUCTIONS

Black lead Red lead

14

ENGLISH

OPERATING INSTRUCTIONS

DIODE TEST

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Continuity/Resistance/Diode-Test setting.

NOTE: The meter defaults to Continuity testing in this mode. Press

the "SEL" button

9

twice to enter Diode testing mode. The Diode

icon will appear on the display.

2. Touch test leads to diode. A reading of 200-800mV on display

indicates forward bias, "OL" indicates reverse bias. An open

device will show "OL" in both polarities. A shorted device will

show approximately 0mV.

FREQUENCY / DUTY-CYCLE

1. Insert RED test lead into VΩ jack

5

and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Frequency/Duty-Cycle setting.

NOTE: The meter defaults to Frequency testing in this mode. To enter

Duty-Cycle testing mode, press the "SEL" button

9

once. Ensure

that the appropriate icon (either

Hz

or

%

) appears on the display.

2. Measure by connecting test leads across the circuit.

CAPACITANCE

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Capacitance setting.

2. Remove power from circuit.

3. Measure capacitance by connecting test leads across the capacitor.

The meter will auto-range to display the measurement in the most

appropriate range.

Black lead Red lead

15

TEMPERATURE

1. Insert K-type thermocouple (with adapter) into the VΩ

5

and

COM

4

jacks (observe polarity markings on thermocouple

and meter), and rotate function selector switch

2

to the

Temperature setting.

NOTE: The meter defaults to Fahrenheit scale in this mode. To enter

Celsius scale, press the "SEL" button

9

once. Ensure that the

appropriate icon (either

°F

or

°C

) appears on the display.

NOTE: The meter may be set to default to the Celsius scale by

powering-ON the meter from the OFF position with the Data Hold

& Backlight button

6

depressed. To re-set the default to the

Fahrenheit scale repeat the power-ON sequence.

2. To measure temperature, make contact between the

thermocouple tip and the object being measured. When

thermocouple tip and object are in thermal equilibrium, the

measurement on the display will stabilize. The meter will auto-

range to display the measurement in the most appropriate range.

Remove thermocouple before switching meter to other

measurement functions.

T

he thermocouple included with the original purchase

is suitable for temperatures below 356°F / 180°C only.

To measure higher temperatures, a K-type thermocouple

with the appropriate measurement range should be used.

1. Remove power from circuit.

2. Measure capacitance by connecting test leads across the capacitor.

The meter will auto-range to display the measurement in the most

appropriate range.

OPERATING INSTRUCTIONS

Black lead Red lead

RED

BLACK

K-Type Thermocouple

(with adapter)

Thermocouple

Adapter

16

MAINTENANCE

BATTERY REPLACEMENT

When indicator is displayed on LCD, batteries must be replaced.

1. Remove screw from battery door.

2. Replace 2 x AAA batteries (note proper polarity).

3. Replace battery door and fasten securely with screw.

T

o avoid risk of

electric shock, disconnect

leads from any voltage

source before removing

battery door.

To avoid risk of

electric shock, do not

operate meter while

battery door is removed.

CLEANING

Be sure meter is turned off and wipe with a clean, dry lint-free

cloth.

Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when meter is not in use for a prolonged

period of time. Do not expose to high temperatures or

humidity. After a period of storage in extreme conditions

exceeding the limits mentioned in the General Specifications

section, allow the meter to return to normal operating

conditions before using.

FCC & IC COMPLIANCE

See this product’s page at www.kleintools.com

for FCC compliance information.

Canada ICES-003 (B) / NMB-003 (B)

WARRANTY

www.kleintools.com/warranty

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash. Items

must be properly disposed of in accordance with local regulations.

Please see www.epa.gov/recycle for additional information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street Lincolnshire, IL 60069 1-800-553-4676

[email protected] www.kleintools.com

ENGLISH

ESPAÑOL

MANUAL DE INSTRUCCIONES

Multímetro digital de gancho

de rango automático de

600A CA

True RMS

Tecnología de

medición

MANUAL DE INSTRUCCIONES

Multímetro digital de gancho

de rango automático de

True RMS

Tecnología de

• MULTÍMETRO

DE VOLTAJE SIN

CONTACTO

• BAJA IMPEDANCIA

• RETENCIÓN DE

DATOSY RANGO

• CONTINUIDAD POR

INDICADOR AUDIBLE

• PRUEBA DE DIODO

• CAPACITANCIA Y

FRECUENCIA

600 A

60 M

Ω

1000 V

CL700

-14° –

1000°F

(-26° –

538°C)

IP40

2m

5000573

CAT IV

600V

CAT III

1000V

18

ESPECIFICACIONES GENERALES

Klein Tools CL700 es un multímetro digital de gancho de rango

automático con media cuadrática real (TRMS) que mide corriente CA

con la pinza; mide voltaje CA/CD, resistencia, continuidad, frecuencia y

capacitancia, prueba diodos con cables de prueba y mide temperatura

con una sonda de termopar. También cuenta con un modo de baja

impedancia (LoZ) para identificar y eliminar voltajes fantasma o erráticos.

• Altitud de funcionamiento: 6562pies (2000m)

• Humedad relativa: <80% sin condensación

• Temperatura de operación: 32°F a 104°F (0°C a 40°C)

• Temperatura de almacenamiento: 14° F a 140°F (-10°C a 60°C)

• Precisión: valores establecidos según una temperatura

ambiente de 65°F a 83°F (18°C a 28°C)

• Coeciente de temperatura: 0,1 × (precisión indicada) por

cada °C por encima de los 28°C o por debajo de los 18°C, es

necesario realizar correcciones si la temperatura del ambiente de

trabajo se encuentra fuera del rango de precisión de temperatura

• Dimensiones: 9,09" × 3,82" × 1,54" (231mm × 97mm × 39mm)

• Peso: 11,8oz (335g) incluidas las baterías

• Calibración: precisa durante un año

• Normas: Cumple con: UL STD 61010-1, 61010-2-032,

61010-2-033.

Certificado según las normas:

CSA STD C22.2 # 61010-1, 61010-2-032,

61010-2-033.

IEC EN 61010-1, 61010-2-032,

61010-2-033, 61326-1.

• Grado de contaminación: 2

• Precisión: ± (% de lectura + cantidad de dígitos

menossignificativos)

• Protección ante caídas: 6,6pies (2m)

• Clasicación de seguridad:

CAT IV 600V, CAT III 1000V,

clase2, doble aislamiento

CAT III: La categoría III de medición es aplicable a los circuitos de

medición y prueba conectados a la distribución de la instalación

de suministro eléctrico de un edificio.

CAT IV: La categoría IV de medición es aplicable a los circuitos

de medición y prueba conectados a la fuente de la instalación de

suministro eléctrico de un edificio.

• Entorno electromagnético: IEC EN 61326-1. Este equipo

cumple con los requisitos apropiados para su uso en entornos

electromagnéticos básicos y controlados como propiedades

residenciales, establecimientos comerciales e instalaciones de

industria ligera.

Especificaciones sujetas a cambios.

ESPAÑOL

19

ESPECIFICACIONES ELÉCTRICAS

Función Rango Resolución Precisión

(50Hz/60Hz)

Voltaje CA

(V CA)

6,000V 1mV ± (1,5% + 5 dígitos)

60,00V 10mV ± (1,2% + 5 dígitos)

600,0V 100mV

1000V 1V ± (1,5% + 5 dígitos)

Voltaje CD

(V CD)

600mV 0,1mV ± (1,0% + 8 dígitos)

6,000V 1mV

± (1,0% + 3 dígitos)60,00V 10mV

600,0V 100mV

1000V 1V ± (1,2% + 3 dígitos)

Impedancia de entrada: 10MΩ Rango de frecuencia: 50Hz a 400Hz

Entrada máxima: 1000V CA RMS o 1000V CD

Corriente CA

(A CA)

60,00A 10mA ± (2,0% + 8 dígitos)

600,0A 100mA ± (2,0% + 5 dígitos)

Intervalo de frecuencia: 50Hz a 60Hz

Función Rango Resolución Precisión

Resistencia

600,0Ω 0,1Ω

± (1,5% + 5 dígitos)

6,000kΩ 1Ω

60,00kΩ 10Ω

600,0kΩ 100Ω

6,000MΩ 1kΩ

60,00MΩ 10kΩ ± (2,0% + 10 dígitos)

Entrada máxima: 600V CA RMS o 600V CD

Capacitancia

60,00nF 0,010nF ± (5,0% + 35 dígitos)

600,0nF 0,1nF

± (3,0% + 5 dígitos)6,000µF 0,001µF

60,00µF 0,01µF

600,0µF 0,1µF ± (5,0% + 5 dígitos)

6000µF 1µF

Entrada máxima: 600V CA RMS o 600V CD

Temperatura

(Fahrenheit)

-14°F a 32°F

0,1°F a 1°F

± (2,0% + 9°F)

33°F a 752°F ± (1,0% + 5,4°F)

753°F a 1000°F ± (2,0% + 9°F)

Temperatura

(Celsius)

-26°C a 0°C

0,1°C a 1°C

± (2,0% + 5°C)

1°C a 400°C ± (1,0% + 3°C)

401°C a 538°C ± (2,0% + 5°C)

20

ESPAÑOL

ESPECIFICACIONES ELÉCTRICAS

FRECUENCIA (RANGO AUTOMÁTICO)

9,999Hz 0,001Hz

± (1,0% + 5 dígitos)

99,99Hz 0,01Hz

999,9Hz 0,1Hz

9,999kHz 1Hz

99,99kHz 10Hz

500,00kHz 100 Hz

Sensibilidad: >8V RMS

Entrada máxima: 600V CD o 600V CA RMS

CICLO DE SERVICIO

1% a 99,9%

0,1% ± (1,2% + 2 dígitos)

Ancho de pulso: 0,1ms – 100ms

Ancho de frecuencia: 5Hz a 10kHz

Sensibilidad: >8V RMS

Entrada máxima: 600V CD o 600V CA RMS

OTRAS APLICACIONES DE MEDICIÓN

Entrada máxima: 600V CA RMS o 600V CD

• Prueba de diodo: 1,5mA máx., 3,0V CD de voltaje de circuito abierto

aprox.

• Vericación de continuidad: señal audible <50Ω, <0,35mA

decorriente de prueba

• Frecuencia de muestreo: 3 muestras por segundo

• Baja impedancia (Low Z): Impedancia de entrada > 3 kΩ

Entrada máx. 600 V RMS

• Apagado automático: después de aprox. 30minutos de inactividad

• Sobrecarga:

se indica "OL" en pantalla, protección contra sobrecarga de

1000V en posición de voltaje, 600VRMS en las demás

posiciones

• Polaridad: "-" en pantalla indica polaridad negativa

• Pantalla: LCD de 3-5/6dígitos con recuento de 6000

La page est en cours de chargement...

Klein Tools CL700 Manuel utilisateur

Klein Tools CL700 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents