Hangzhou Great Star Industrial IM040304 Mode d'emploi

IM040304
Marque
Hangzhou Great Star Industrial
Modèle
IM040304
Taper
Mode d'emploi
WIRELESS REMOTE CONTROL E26 LIGHT BULB
SOCKET & LAMP SWITCH KIT USER GUIDE
Spec:
Remote control socket
Remote control switch
Base type: Standard E26
Working voltage: 120VAC/60Hz
Maximum load: 40W
Wireless protocol: 433.925MHz
Working temperature: 0~40
Size: Die 60MM x 62mm Model
No. :IM040303
Power: 3V(CR2032x1
included) Wireless protocol:
433.925MHz Working
temperature: 0~40 Max
Remote Control Distance:
35 meters. (Free Area)
size: 70mm 115mm* 14mm
Model No. :IM040304
1. Install the remote control socket to the present standard E26
socket. Install the light bulb onto the remote control socket.
2. Mount the remote control switch to the wall mount or stick the
switch to anywhere you like.
1. Power the socket.
2. Long press set button 2 seconds. The button flashes blue
slowly indicates the socket entered pairing mode.
3. Press the switch to pair. The button flashes 3 times indicates
the switch and the socket paired succeed.
* Socket will quit the pairing mode if no switch been paired in 30
seconds. Or you may quit pairing mode by pressing the set
button.
Long press set button 10 seconds to unpair all the switch that
paired to this socket. The button flashes 3 times indicates the
switch and the socket unpaired succeed.
How to use:
How to unpair?
How to pair?
Pairing options
We have 2 optional control kits available for you.
a. Multiple switches controls one socket. ( max 10
switches )
b. One switches controls One socket.
a b
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This device
complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Hangzhou Great Star Industrial IM040304 Mode d'emploi

IM040304
Marque
Hangzhou Great Star Industrial
Modèle
IM040304
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Autres documents