Progress Lighting 93114662 B Guide d'installation

Marque: Progress Lighting

Modèle: 93114662 B

Catégorie: Ventilateurs ménagers

Taper: Guide d'installation

Ceiling Fan Installation Manual

P250040

93114662_B

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

109226

785247240883

785247240890

785247240906

Limited Lifetime Warranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so

long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to

be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic

blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of

any sea coast. Extended warranties for ENERGY STAR® qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are

warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance

with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for

fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical

components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no

warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for

replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864) 678-1000 for repair or replacement

which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not

limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or

neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without

limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or

attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS

LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR

CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or

consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights

and you may have other rights which vary from state to state.

Table of Contents

Safety Rules.....................................................................................................................................................................................

Unpacking Your Fan .......................................................................................................................................................................

Installing Your Fan .........................................................................................................................................................................

Installing the Light Kit and Glass Shade ........................................................................................................................................

Operating Your Transmitter ..........................................................................................................................................................

Care of Your Fan ...........................................................................................................................................................................

Troubleshooting ............................................................................................................................................................................

Specifications ................................................................................................................................................................................

10.

12.

13.

1. Safety Rules

To reduce the risk of electric shock, ensure electricity has been turned off

at the circuit breaker or fuse box before beginning.

All wiring must be in accordance with the National Electrical Code

“ANSI/NFPA 70-1999” and local electrical codes. Electrical installation

should be performed by a qualified licensed electrician.

The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less. Use

only cUL-listed outlet boxes marked “FOR FAN SUPPORT.”

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from

the trailing edge of the blades to the floor.

Avoid placing objects in the path of the blades.

To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

Do not use water or detergents when cleaning the fan or fan blades. A dry

dust cloth or lightly dampened cloth will be suitable for most cleaning.

After making electrical connections, spliced conductors should be turned

upward and pushed carefully up into the outlet box. The wires should be

spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box and ungrounded conductor on the

other side of the outlet box.

All set screws must be checked and retightened where necessary before

installation.

Suitable for use with solid-state speed control.

This device contains licence-exempt transmitter(s)/receiver(s) that comply

with innovation, Science and Economic Development Canada’s licence-

exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that

may cause undesired operation of the device.

10.

11.

NOTE

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF PERSONALL INJURY, DO NOT BEND

THE BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN

INSTALLING THE BRACKETS, BALANCING THE BLADES OR

CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS IN –

BETWEEN ROTATING FAN BLADES.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR OTHER PERSONAL

INJURY, MOUNT FAN ONLY ON AN OUTLET BOX OR SUPPORTING

SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG)

OR LESS AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET

BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF

LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF

IN DOUBT.

Unpack your fan and check the contents. You should have the following items:

Unpacking Your Fan 2.

13. Loose parts bag containing:

a. Blade holders attachment hardware

1/4"x22mm screws with lock washers (9)

b. Blade attachment hardware

1/4"x1/2" screws with lock washers (9)

c. Mounting hardware

Wire nuts (3)

1. Fan blades (4)

2. Canopy assembly

3. Ball/downrod assembly

4. Coupling cover

5. Fan motor assembly

6. Set of blade holders (4)

7. Mounting plate

8. 24 Watt LED light kit

9. Glass shade

10. Transmitter incl. holder + 2 mounting screws

11. 12V battery

12. Balancing kit

Tools Required

Phillips screw driver, straight slot screw driver,

adjustable wrench, step ladder, and wire cutters.

Mounting Options

If there isn't an existing cUL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the

fan (at least 35 lbs). Do not use plastic outlet

boxes.

Figure 4

Figure 3

Figure 1

Figure 2

Outlet box

Outlet box Outlet box

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at your Progress Lighting Retailer).

3. Installing Your Fan

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR OTHER PERSONAL INJURY,

MOUNT FAN ONLY TO AN OUTLET BOX

MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX. OUTLET

BOXES COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURES MAY NOT

BE ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Angled ceiling

maximum

24 angle

Recessed

outlet box

Provide strong support

Ceiling

hanger

bracket

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly:

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counter clockwise.(Fig. 5)

Step 2. Remove the mounting bracket from

the canopy by removing the 1 of 2 screws

from the bottom of the mounting bracket and

loosening the other one a half turn from the

screw head. Next, turn the canopy counter

clockwise to removing the mounting bracket

from the canopy. (Fig. 5)

Step 3. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shown in Fig. 6.

Step 4. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided with your outlet box.

Step 5. Remove the hanger pin, lock pin and

set screws from the top of the motor

assembly. (Fig. 7)

Step 6. Route the safety cable and wires

exiting from the top of the fan motor through

the coupling cover, canopy cover and canopy

and then through the ball / downrod. (Fig. 7)

Step 7. Align the holes at the bottom of the

downrod with the holes in the collar on top of

the motor housing (Fig. 7). Carefully insert

the hanger pin through the holes in the collar and

downrod. Be careful not to jam the pin against the

wiring inside the downrod. Insert the locking pin

through the hole near the end of the hanger pin until it

snaps into its locked position, as noted in the circle

inset of Fig. 7.

WARNING

FAILURE TO PROPERLY INSTALL

LOCKING PIN AS NOTED IN STEP 7

COULD RESULT IN FAN LOOSENING AND

POSSIBLY FALLING.

Figure 6

Figure 7

Ceiling

hanger

bracket

Mounting screws

(supplied with

electrical box)

cUL Listed

electrical

box

120V Wires

Washers

Supply wires

Downrod

Hanger pin Lock pin

Set screws

Canopy

Canopy cover

Coupling cover

Pin in locked

position

Step 8. Tighten two set screws on top of the fan

motor firmly. (Fig. 7)

Step 9. Place the downrod ball into the hanger

bracket socket. (Fig. 8)

Step 10. Secure the safety cable to the building

structure with a wood screw. (wood screw not

supplied) (Fig. 8)

Figure 5

Ceiling hanger

bracket

Ceiling

canopy

Canopy

cover

Safety cable

Make the Electrical

Connections

WARNING: To avoid possible electrical shock,

be sure electricity is turned off at the main fuse

box before wiring.

Step 1. Motor to House Supply Wires Electrical

Connections: Connect the WHITE wire

(Neutral) from the outlet box to the WHITE wire

marked "AC in N" from the motor. (Fig. 9)

Step 2. Connect the BLACK wire (Hot) from

the outlet box to the BLACK wire marked "AC

in L" from the motor. (Fig. 9)

Secure all wire connections with the plastic wire

nuts provided.

Figure 9

Outlet Box

Black ("AC IN L")

White ("AC IN N")

White (Neutral)

Black (Hot)

Green or bare

copper (ground)

Ground (green)

(Connect to

ground wire on

hanger bracket if

no house ground

wire exists.)

Figure 8

Hanger

bracket

Canopy

Safety cable

Finishing the Installation

Step 1. Tuck connections neatly into ceiling

outlet box.

Step 2. Slide the canopy up to mounting bracket

and place the key hole on the canopy over the

screw on the mounting bracket, turn canopy until

it locks in place at the narrow section of the key

holes. (Fig. 10)

Step 3. Align the circular hole on canopy with the

remaining hole on the mounting bracket, secure

by tightening the two set screws. Note: Adjust the

canopy screws as necessary until the canopy and

canopy cover are snug.

Attaching the Blade Holders

Step 1. Insert the blade holder through the slot in

the housing. Align the holes in the blade and the

fan motor assembly and secure with the blade

holder attachment screws (1/4"x22mm) with lock

washers. (Fig. 11)

Step 2. Repeat this procedure with the remaining

blade holders.

WARNING

Make sure the notch on the hanging bracket

properly sits in the groove in the hanger ball

before attaching the canopy to the bracket by

turning the housing until it drops into place.

Figure 10

Outlet box

Hanger

bracket

Canopy

Canopy cover

Screws

Figure 11

Screws (1/4"x22mm)

with lock washers

Blade holders

Blade Balancing

All blades are grouped by weight. The fan may

wobble even though the blades are weighed

equally.

The following procedure should correct most

fan wobbling problems. Check after each step.

1. Check that all blade and blade arm screws are

secure.

2. Most fan wobbling problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 13. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance deviation should be equal within

1/8".

3. Use the enclosed Blade Balancing Kit if the

blade wobble is still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result in smoother operation.

Touching

ceiling

Figure 13

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

HOLDERS WHILE INSTALLING,

BALANCING THE BLADES, OR CLEANING

THE FAN. DO NOT INSERT FOREIGN

OBJECTS BETWEEN ROTATING FAN

BLADES.

Attaching the Fan Blades

Step 1. Insert the blade through the hole in the

blade holder and housing. Align the holes in the

blade, blade holder through and the fan motor

assembly and secure with the blade attachment

screws (1/4"x1/2") with lock washers. (Fig. 12)

Step 2. Repeat this procedure with the remaining

blades.

Figure 12

Screws (1/4"x1/2")

with lock washers

Blades

Blade holders

Installing the

Light Kit and Glass Shade

Figure 15

LED light kit

Glass shade

Screws

Mounting

plate

Figure 14

Mounting

plate

Screws

Mounting ring

Wire connectors

CAUTION: Before starting installation,

disconnect the power by turning off the circuit

breaker or removing the fuse at fuse box.

Turning power off using the fan switch is not

sufficient to prevent electric shock.

Step 1. Remove 1 of 3 screws from the posts of

the mounting ring and keep it for future use.

Loosen the other 2 screws. (Do not remove)

Step 2. Place the key holes in the mounting plate

over the two screws previously loosened from

the mounting ring. Turn the mounting plate until

the decorative cover locks in place at the narrow

section of the key holes. (Fig. 14)

Step 3. Securely tighten the two mounting

screws previously loosened and the one

previously removed.

Step 4. While holding the LED light kit under

the fan motor assembly, make the 2-pin wire

connections: (Fig. 15)

- White to white - Black to black

Step 5. Remove 1 of 3 screws from the posts of

the mounting plate and keep it for future use.

Loosen the other 2 screws. (Do not remove)

Step 6. Place the key holes in the LED light kit

over the two mounting screws previously

loosened from the mounting plate). Turn the

LED light kit until the light kit locks in place at

the narrow section of the key holes. Secure by

tightening the two light kit mounting screws

previously loosened and the one previously

removed. (Fig. 15)

Step 7. Raise glass shade up against the light kit

and secure it to fan by turning glass clockwise

until snug. DO NOT OVERTIGHTEN.

9. Operating Your Transmitter

Installing the battery

Install a 12V battery (included) into the remote

control. To prevent damage to the remote control,

remove the battery if not used for long periods. (Fig.

16)

Figure 16

ON ECE

1234

a) Select desired frequency from the transmitter.

The

dip switches can be set to 16 different combinations.

(Fig. 18)

b) From the back of the transmitter,

with the

fan’s power off, restore power to the fan. Press

and hold “SET” button for about 5 seconds and

release. If optional light kit is installed, the

light kit will flash twice and the signal light on

the hand held transmitter will come on when

the button is pressed. The fan has completed

the pairing process with the remote control and

is ready for use. (Fig. 18)

NOTE: If the self calibration test failed, turn

the AC power off; restore power and process

the self calibration test again.

NOTE: During self calibration test, the remote

is non-fuctional.

NOTE: The learning frequency function and

self calibration test will continue to retain the

last set frequency and calibration set even

when the AC power is shut off. If the

frequency is changed the self calibration test

will occur again.

Over 80W protection: When the receiver

detects motor power consumption which is

greater than 80W, the receiver power will be

stopped and operation will immediately

discontinue. Wait for 5 seconds and then turn

the receiver power back on.

Remote Control Button Definitions:

(Fig. 17)

These six buttons are used to set the fan speed as

follows:

I = minimum speed

II = low speed

III = medium low speed

IV = medium speed

V = medium high speed

VI = high speed

button: Turns the fan off.

button: Controls fan direction.

button: Controls light. Switch the “D” and “ON” dip

switch on the back of transmitter to decide the light in

“ON/OFF” or “Dimmable” condition.

(Fig. 18)

Your DC brushless motor is equipped with an

automatically learned type remote control. There are

no frequency switches on the receiver; the receiver

unit will automatically scan the frequency from the

remote control if any changes are made. The

frequency settings on the transmitter should be

changed ONLY in case of interference or if a

second or more ceiling fans with the same type of

control system are installed in the same structure.

Setting the Remote Control

Follow the below steps to set the remote control:

The auto learning function will only mandate within

60 seconds when turning the fan’s AC power ON.

Figure 18

Figure 17

ON ECE

1234

ON ECE

1234

Speed settings for warm or cool weather depend on

factors such as the room size. Ceiling height,

number of fans and so on.

NOTE: To operate the reverse function on this fan,

press the reverse button while the fan is running.

Warm weather - (Forward) A downward airflow

creates a cooling effect as shown in Fig. 19. This

allows you to set your air conditioner on a warmer

setting without affecting your comfort.

Cool weather - (Reverse) An upward airflow moves

warm air off the ceiling area as shown in Fig. 20.

This allows you to set your heating unit on a cooler

setting without affecting your comfort.

Figure 19

Figure 20

10.

Step 1. Remove the remote control holder cover

from the remote control holder.

Step 2. Attach the remote control holder with the

two remote control holder mounting screw

provided. (Fig. 21)

Step 3. Replace the remote control holder cover

into remote control holder.

Remote

Control

Holder

Remote Control

Holder Cover

Screws

Installing the Remote Control

Holder

Figure 21

Here are some suggestions to help you maintain

your fan

1. Because of the fan's natural movement, some

connections may become loose.

Check the

support connections, brackets, and blade

attachments twice a year.

Make sure they are

secure.

(It is not necessary to remove fan from

ceiling.)

2. Clean your fan periodically to help maintain

its new appearance over the years. Use only a

soft brush or lint-free cloth to avoid scratching

the finish. The plating is sealed with a lacquer to

minimize discoloration or tarnishing. Do not use

water when cleaning. This could damage the

motor, or possibly cause an electrical shock.

There is no need to oil your fan.

The motor

has permanently lubricated bearings.

IMPORTANT

MAKE SURE THE POWER IS OFF AT THE

ELECTRICAL PANEL BOX BEFORE YOU

ATTEMPT ANY REPAIRS. REFER TO THE

SECTION "MAKING ELECTRICAL

CONNECTIONS".

11. Care of Your Fan

Troubleshooting

12.

Solution

1. Check circuit fuses or breakers.

2. Check line wire connections to the fan and switch wire connections in the switch housing.

CAUTION: Make sure main power is off.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade bracket to the motor hub is tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

CAUTION: Make sure main power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Check that light bulb is also secure.

6. Some fan motors are sensitive to signals from solid-state variable speed controls. If you have installed this type of control,

choose and install another type of control.

7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the ceiling.

1. Turn the AC power off to fan, and re-do steps for programming on page 9.

2. Do not turn off fan from standard wall switch. Use only our wall switch or your remote to regulate fan.

Problem

Fan will not start.

Fan sounds noisy.

Fan has lost its

programming

repeatedly.

13.

Specifications

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

701 Millennium Blvd.,

Greenville, SC 29607

18.74

lbs

21.23

lbs

2.96'

Fan Size

Speed Volts

Amps Watts RPM CFM N.W. G.W. C.F.

56"

Low

High

120

These are approximate measures. They do not include Amps and Wattage used by the light kit.

0.051

0.46

2.34

34.64

156

1841.29

6112.61

Manuel d'installation du ventilateur de plafond

93114662_B P250040

Garantie à vie limitée

Progress Lighting garantit à l’acheteur initial que les moteurs de ventilateur sont exempts de défauts électriques ou mécaniques

tant que l’acheteur initial est propriétaire du ventilateur. Les interrupteurs à chaînette, les interrupteurs inverseurs, les

condensateurs et les finis métalliques sont garantis contre les défauts de matériaux ou de fabrication pendant une période d’un

an à partir de la date d’achat. Le gauchissement des pales de bois ou de plastique n’est pas couvert par la présente garantie, ni la

corrosion ou la détérioration du fini des ventilateurs installés à moins de dix milles d’un bord de mer. Les garanties prolongées

pour les produits homologués ENERGY STAR® peuvent s’appliquer.

Lorsqu’ils sont installés correctement et dans des conditions d’utilisation normales, les ventilateurs de plafond Progress

Lighting dotés d’une source lumineuse à DEL intégrée sont garantis contre les défauts de matériaux et de fabrication causant le

non fonctionnement de la source lumineuse selon les spécifications pendant (i) cinq (5) ans à partir de la date d’achat des

modules d’éclairage à DEL et des composants électriques des ventilateurs pour les résidences unifamiliales et (ii) trois (3) ans à

partir de la date d’achat des modules d’éclairage à DEL et des composants électriques des ventilateurs pour les résidences

multifamiliales et pour les utilisations commerciales. Les ampoules à DEL fournies par Progress Lighting ne sont assorties

d’aucune autre garantie que celle du fabricant. Les ampoules autres qu’à DEL ne sont assorties d’aucune garantie.

En fournissant la preuve d’achat, l’acheteur initial peut retourner le ventilateur défectueux à son lieu d’achat pendant les 30

premiers jours afin qu’il soit remplacé. Après 30 jours, l’acheteur initial DOIT communiquer avec Progress Lighting au 864

678-1000 pour la réparation ou le remplacement du ventilateur, ce qui sera déterminé exclusivement par Progress Lighting et

constituera le seul et unique recours de l’acheteur.

Main-d’oeuvre et expédition exclus. La présente garantie ne couvre par les coûts et les frais associés à la main-d’oeuvre (y

compris, sans s’y limiter, les frais d’électricien) nécessaires à l’installation, au retrait ou au remplacement du ventilateur ou des

pièces du ventilateur.

La présente garantie ne s’applique pas en cas de perte ou de dommage découlant (i) de l’usure normale, de l’altération ou d’un

usage incorrect, abusif ou négligent ou (ii) d’une installation, d’une utilisation, d’une réparation ou d’un entretien inadéquats par

l’acheteur initial ou un tiers, y compris, sans s’y limiter, une tension électrique inadéquate ou une surtension, l’utilisation de

pièces ou d’accessoires inadéquats, une réparation non autorisée (effectuée ou tentée) ou l’omission d’entretenir le ventilateur.

LES GARANTIES QUI PRÉCÈDENT ÉNONCENT L’ENTIÈRE RESPONSABILITÉ DE PROGRESS LIGHTING AU

CHAPITRE DE LA GARANTIE AINSI QUE LE SEUL ET UNIQUE RECOURS DE L’ACHETEUR LIÉ À CES PRODUITS.

PROGRESS LIGHTING N’EST PAS RESPONSABLE DES DOMMAGES (Y COMPRIS LES DOMMAGES INDIRECTS,

SPÉCIAUX, ACCESSOIRES OU CONSÉCUTIFS) ATTRIBUABLES À LA DÉFECTUOSITÉ DU PRODUIT, QU’ILS

SOIENT LIÉS À UNE VIOLATION DE LA GARANTIE, UNE VIOLATION DU CONTRAT OU AUTRE. LA PRÉSENTE

GARANTIE REMPLACE TOUTE AUTRE GARANTIE, EXPRESSE OU IMPLICITE, Y COMPRIS TOUTE GARANTIE

DE QUALITÉ MARCHANDE, D’UTILITÉ À UNE FIN PARTICULIÈRE OU D’ABSENCE DE CONTREFAÇON.

Certains États ne permettent pas de limitation à la durée implicite d’une garantie ou d’exclusion ou de limitation des dommages

accessoires ou consécutifs. Par conséquent, les limitations ci-dessus pourraient ne pas s’appliquer

Date de l’achat

Magasin

Nº de modèle

Nº de série

Nº du fournisseur

CUP

109226

785247240883

785247240890

785247240906

Règles de sécurité

........................................................................................................................................................................

Déballer votre ventilateur

...........................................................................................................................................................

Installation du ventilateur

...........................................................................................................................................................

Installation de la luminaire led et l'abat-jour en verre

............................................................................................................

Le fonctionnement de votre transmetteur

...............................................................................................................................

Entretien du ventilateur

.............................................................................................................................................................

Recherche des pannes

................................................................................................................................................................

Spécifications

..............................................................................................................................................................................

10.

12.

13.

Table des matières

Pour rèduire les risques de décharge électrique, s'assurer que l'électricité

est coupée au disjoncteur ou au boîtier de fusibles avant de commencer.

Tous les càblages doivent se conformer au Code National de électricite ét

aux normes électriques locales. L'installation électrique doit être

effectuée par un électricien licencié qualifie.

Le boîtier de prise et son support doivent être attachés correctement et

capables de supporter fiablement un poids minimum de 15.8 kg (35

livres). Utiliser seulement les boîtiers de prise homologués par l'cUL et

portant l'étiquette "POUR LE SUPPORT DE VENTILATEUR".

Le ventilateur doit être monté à une hauteur minimum de 2.1m (7

pieds) entre le bord de fuite des ailettes et le sol.

Éviter de placer des objets en travers des ailettes.

Pour éviter les blessures ou les dommages du ventilateur et autres

articles, faire attention en travaillant sur le ventilateur ou en le nettoyant.

Ne pas utilliser d'eau ou de détergent pout nettoyer le ventilateur ou ses

ailettes. Un chiffon de poussiére sec ou un chiffon lègérement humide

suffit pour la plupart des nettoyages.

Aprés le branchement électrique, las épissures de conducteurs doivent

être orientées vers le haut et poussées soigneusement dans le boîtier de

prise. Les fils doivent être éloignés les uns des autres, et le conducteur

mis à la terre et le conducteur de mise à la terre de l'appareil doivent être

placés sur un coté du boîtier de prise.

Toutes les vis de réglage doivent être vérifiées et resserrées si nécessaire

avant l'installation.

Adapté pour une utilisation avec la commande de vitesse à l'état solide.

10.

1. Règles de sécurité

REMARQUE

LIRE ET CONSERVER CES INSTRUCTIONS

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES DE BLESSURE, NE PLIEZ PAS LES

SUPPORTS DE PALE (AUSSI APPELÉS BRIDES) PENDANT

L'INSTALLATION DES CROCHETS, L'ÉQUILIBRAGE DES PALES OU LE

NETTOYAGE DU VENTILATEUR.

AVERTISSEMENT

AFIN DE RÉDUIRE LE RISQUE D’ INCENDIE, DE DÉCHARGE ÉLECTRIQUE,

DE BLESSURE CORPORELLE, INSTALLER À UNE BOÎTE DE SORTIE

CAPABLE DE « SOUTENIR UN VENTILATEUR DE 15,8 KG (35 LB) OU

MOINS » ET UTILISER LES VIS D’ INSTALLATION COMPRISES AVEC LA

BOÎTE DE SORTIE. LA PLUPART DES BOÎTES DE SORTIE UTILISÉES POUR

SOUTENIR LES LUMINAIRES SONT INADAPTÉES AU SOUTIEN D’ UN

VENTILATEUR ET POURRAIENT EXIGER UN REMPLACEMENT. À CAUSE

DE L’ INSTALLATION COMPLEXE DE CE VENTILATEUR, NOUS

RECOMMANDONS LES SERVICES D’UN MAÎTRE ÉLECTRICIEN.

Cet appareil contient des émetteurs/récepteurs exemptés de licence

conformes aux RSS, les innovations exemptées de licence de Science et

Développement économique Canada. Le fonctionnement est soumis aux

deux conditions suivantes:

(1) Cet appareil ne doit pas causer d'interférences.

(2) Cet appareil doit accepter toutes les interférences, y compris celles

susceptibles de provoquer un fonctionnement indésirable de

l'appareil.

11.

La page charge ...

Progress Lighting 93114662 B Guide d'installation

Marque: Progress Lighting

Modèle: 93114662 B

Catégorie: Ventilateurs ménagers

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Progress Lighting 93114662 B Installation guide
español: Progress Lighting 93114662 B Guía de instalación

Progress Lighting 93114662 B Guide d'installation

Progress Lighting 93114662 B Guide d'installation

dans d''autres langues

Documents connexes

Autres documents