NOMA Ashton 5-Blade 3-Speed Le manuel du propriétaire

ASHTON 44” LED CEILING FAN

PRODUCT NO. 052-9603-8

USER MANUAL

READ AND SAVE THESE INSTRUCTIONS

TABLE OF CONTENTS

3

01. SAFETY/CAUTIONS

02. TOOLS REQUIRED

03. EXPLODED VIEW

04. ELECTRICAL SAFETY

05. ASSEMBLY

06. OPERATION

07. TROUBLESHOOTING

08. DYNAMIC BLADE BALANCING KIT

09. MAINTENANCE

10. WARRANTY & DISPOSAL

4

6

7

11

13

19

21

23

25

26

11. IC STATEMENT 27

4

SAFETY / CAUTIONS

SAFETY CONCERNS

•

TO REDUCE THE RISK OF ELECTRIC SHOCK, ENSURE ELECTRICITY HAS

BEEN TURNED OFF AT THE CIRCUIT BREAKER OR FUSE BOX BEFORE

BEGINNING.

ALL WIRING MUST BE IN ACCORDANCE WITH NATIONAL AND LOCAL

ELECTRICAL CODES. ELECTRICAL INSTALLATION SHOULD BE PERFORMED

BY A QUALIFIED LICENSED ELECTRICIAN.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO

NOT USE THIS FAN WITH ANY SOLID-STATE FAN-SPEED CONTROL

DEVICE. IT WILL PERMANENTLY DAMAGE THE ELECTRONIC CIRCUITRY.

CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, USE ONLY THE

SCREWS PROVIDED WITH THE OUTLET BOX.

THE OUTLET BOX AND SUPPORT STRUCTURE MUST BE SECURELY

MOUNTED AND CAPABLE OF RELIABLY SUPPORTING A MINIMUM OF

35 LB (15.9 KG). USE ONLY UL-LISTED OUTLET BOXES MARKED “FOR FAN

SUPPORT.”

THE FAN MUST BE MOUNTED WITH A MINIMUM OF 6’11’’(2.1M) FROM

THE TRAILING EDGE OF THE BLADES TO THE FLOOR.

AVOID PLACING OBJECTS IN THE PATH OF THE BLADES.

TO AVOID PERSONAL INJURY OR DAMAGE TO THE FAN AND OTHER

ITEMS, BE CAUTIOUS WHEN WORKING AROUND OR CLEANING THE

FAN.

DO NOT USE WATER OR DETERGENTS WHEN CLEANING THE FAN

OR FAN BLADES. A DRY DUST CLOTH WILL BE SUITABLE FOR MOST

CLEANING.

AFTER MAKING ELECTRICAL CONNECTIONS, SPLICED CONDUCTORS

SHOULD BE TURNED UPWARD AND PUSHED CAREFULLY UP INTO

THE OUTLET BOX. THE WIRES SHOULD BE SPREAD APART WITH THE

GROUNDED CONDUCTOR AND THE EQUIPMENT-GROUNDING

CONDUCTOR ON ONE SIDE OF THE OUTLET BOX AND THE

UNGROUNDED CONDUCTOR ON THE OTHER SIDE OF THE OUTLET BOX.

ALL SET SCREWS MUST BE CHECKED AND RE-TIGHTENED WHERE

NECESSARY BEFORE INSTALLATION.

5

01

•

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT” WITH THE SCREWS PROVIDED WITH

THE OUTLET BOX.

WARNING: TO AVOID RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES) OR THE BRACKETS

WHILE BALANCING THE BLADES OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT” OF 35 LB (15.9 KG) OR LESS”

AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX.

MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF

LIGHT FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY

NEED TO BE REPLACED. DUE TO THE COMPLEXITY OF THIS FAN, A

QUALIFIED LICENSED ELECTRICIAN IS STRONGLY RECOMMENDED FOR

INSTALLATION.

6

01 02

TOOLS REQUIRED

INSTALLATION PREPARATION

Flat-head

screwdriver

Cross-head

screwdriver

Safety glasses Pliers

Wire cutters Electrical tape Stepladder Wire strippers

6' 11"

(2.1 m)

30”

(76 cm )

To prevent personal injury and

damage, ensure that the hanging

location allows the blades a

clearance of 6' 11" (2.1 m) from the

floor and 30" (76 cm) from any wall or

obstruction.

This fan can be mounted with a

downrod on a regular (no-slope) or

vaulted ceiling, such as flush mount.

Blade Edge

Flush Mount

Installation

Downrod

Installation

Vaulted

ceiling angle

is not to

exceed 18°

7

03

EXPLODED VIEW

PACKAGE CONTENTS

07

10 11 12

15 16

03

09

14

05 06 08

Installation

Instruction

X 3

X 2

X 3

X 2

X 16 X 3

X 1

X 16

X 5

8

03 EXPLODED VIEW

PACKAGE CONTENTS

01.

02.

03.

04.

05.

06.

07.

08.

HANGER BRACKET

CANOPY

CANOPY COVER

DOWNROD STAND COVER

DOWNROD, HANGER PIN

& LOCK PIN

FAN MOTOR ASSEMBLY

FAN BLADES (5 PCS)

BLADE BRACKETS (5 PCS)

09. LIGHT PLATE

11. REMOTE CONTROL

12. REMOTE CONTROL HOLDER

14. BLADE BALANCING KIT

15. INSTALLATION INSTRUCTIONS

10. 18 W LED ASSEMBLY

13. 12 V BATTERY

16. PARTS PACK CONTAINING:

3 x Wood Screws

2 x Machine Screws

3 x Flat Washers

3 x Spring Washers

2 x Star Washers

3 x Wire Nuts

1 x Blade Bracket Screw

16 x Blade Screws

16 x Fiber Washers

5 x Screw Retainers

9

03

EXPLODED VIEW

DETAIL

01.

02.

03.

04.

05.

06.

07.

08.

09.

10.

HANGER PIN

CANOPY

HANGER BALL

HANGER BRACKET

LIGHT PLATE

COLLAR

BLADE BRACKET

FAN BLADE

LOCK PIN

FAN MOTOR ASSEMBLY

11.

12.

13.

DOWNROD STAND COVER

DOWNROD

CANOPY COVER 18 W LED ASSEMBLY14.

10

03

13

11

01

09

10

02

03

04

07

05

06

08

12

14

11

04

ELECTRICAL SAFETY

Instructions

•

01.

02.

03.

04.

Making the Electrical Connections

•

Read all safety information and installation instructions before

you begin to install the fan and save instructions.

All set screws of the fan must be checked and re-tightened

where necessary before installation.

To reduce the risk of personal injury, do not bend the blade

brackets when installing the brackets, balancing the blades

or cleaning the fan. Do not insert foreign objects between

rotating fan blades.

Before changing the fan direction, turn off the fan and wait for

the fan blades to stop completely.

The safeguards provided by these safety instructions and by

the separate installation instructions are not meant to cover all

possible conditions and situations that may occur. It must be

understood that common sense, caution and care are factors

which cannot be built into this product. These factors must be

supplied by the person(s) installing, caring for and operating

the fan.

WARNING: To avoid risk of electric shock, be sure to shut off

power at the main fuse or circuit breaker box before installing

To reduce the risk of injury, install the fan so that the blades are

at least 6’ 11’’ (2.1M) above the floor and at least 30’’ (76cm)

from the tip of the blades to the wall.

12

04

•

mount the outlet box marked “ACCEPTABLE FOR FAN

SUPPORT” and use mounting screws provided with the outlet

box.

The installation must be in accordance with the national

electrical code, ANSI/NFPA 70-1999 and local codes. If you

are unfamiliar with the methods of installing electrical wiring,

injury, mount to outlet box and use mounting screws provided

with the outlet box.

IMPORTANT: Before you begin installing the fan, carefully read

all information on the separate sheet “SAFETY INSTRUCTIONS”

as well as the following “Installation Instructions Steps”. If in doubt,

NOTE: The fan weight is 13 lb 3 oz (5.99 kg). Be sure the outlet box

you are using is securely attached to the building structure and can

support the full weight of the fan. Failing to do so can result in

serious injury.

consult a qualified electrician.

13

05

01 02

ASSEMBLY

INSTRUCTIONS

Fig. 1 Fig. 2

Outlet

Box

Outlet Box

Screw

03 Fig. 3

Lock

Hanger

Cross Pin

Hanger Ball

Downrod

Remove the lock pin and take out the hanger

pin; then remove the hanger ball from the

downrod assembly by loosening the set

screw and removing the cross pin (Fig. 3).

04

Downrod

Turn OFF the electric circuit at the main

fuse of circuit breaker box (Fig. 1).

Securely attach the hanger bracket to

an outlet box marked "ACCEPTABLE FOR

FAN SUPPORT" using the supplied outlet

box screws with spring washers (Fig. 2).

Lock

Fig. 4

Warning: Ensure wiring is not pinched or

twisted.

Hanger

Bracket

Thread the motor wires safety cable through

the downrod and downrod stand. Insert the

downrod into the collar. Slide hanger pin

through holes of collar and downrod (Fig. 4).

14

05

Cross Pin

Set Screw

Fig. 8Fig. 7

07

Hang the fan onto the hanger bracket,

and make sure the slot of the hanger ball

is aligned with the clip of the hanger

bracket (Fig. 8).

08

Hanger

Bracket

Slot Clip

Insert and tighten the two collar screws.

Slide lock pin into hanger pin until it is

locked into position (Fig. 5).

05

Safety Cable

Hanger

Fig. 6

06

Lock Pin

Downrod

Canopy

Canopy Cover

Collar

Hanger

Downrod

Stand Cover

Fig. 5

Lock Pin

Collar Screws

Motor Wires

Hanger Ball

Slide downrod cover, canopy cover

and canopy over the downrod as

shown (Fig. 6).

Carefully reinstall the hanger ball onto rod,

being sure that cross pin is in correct position,

set screws are tightened and wires are not

twisted (Fig. 7).

15

05

Fig. 9

ASSEMBLY

IMPORTANT: If you are not sure if the electrical outlet box and fan are

grounded, contact a licensed electrician for advice. They must be

grounded for safe operation.

WARNING: To avoid possible electric shock, be sure electricity is turned

off at the main fuse box before wiring.

Wiring Instructions

•

VIEW AFTER INSTALLATION

09

The safety cable prevents the fan from falling. Secure the safety cable to the ceiling joist with

a wood screw, star washer and flat washer (Fig. 9).

Safety

Cable

Star Washer

Wood

Screw

Flat Washer

16

05

NOTE: Fan must be installed at a maximum distance of 40’ (12.2 m) from

the transmitting unit for proper signal transmission between the transmitting

unit and the fan’s receiving unit.

Fan to House Supply Wires Electrical Connections: Connect the WHITE

wire (Neutral) from the outlet box to the WHITE wire marked “AC in N”

from the fan. Connect the BLACK wire (Hot) from the outlet box to the

BLACK wire marked “AC in L” from the fan. Secure all wire connections

with the plastic wire nuts provided.

Between Fan & Mains

•

WIRE NUT

OUTLET BOX

HOT

NEUTRAL

GROUND

AC IN N

OUTLET BOX

YELLOW & GREEN

AC IN L

YELLOW & GREEN

AC IN N

AC IN L

GROUND

HOT

NEUTRAL

Connect the ground wire (yellow & green or bare copper) from the

outlet box to the ground wire of hanging ball and the ground wire of

hanger bracket and the receiver ground wire. Secure wire

connection with the plastic wire nut provided.

•

HANGER

BRACKET

17

05

ASSEMBLY

Remove 1 of the 2 screws from the bottom

of the hanger bracket and loosen the other

one half a turn from the screw head. Slide

the canopy up towards the hanger bracket

and place the key hole on the canopy over

the screw on the hanger bracket, then turn

canopy until it locks in place at the narrow

section of the key holes. Align the circular

hole on the canopy with the remaining

hole on the hanger bracket, secure with

previously removed hanger bracket screw,

and tighten both hanger bracket screws

securely (Fig. 10).

Push up the canopy cover until the screw

heads engage to the slots on the canopy

cover, and rotate the canopy cover until it

is attached to the bottom of the canopy

securely (Fig. 10).

Attach the fan blades to the blade bracket

by using three blade screws and fibre

washers. Tighten screws and fibre washers

securely. Repeat these steps for the

remaining blades (Fig. 11-3).

Remove all the blade bracket screws from

the fan motor assembly, including the

plastic blocks from the fan motor assembly.

Discard the plastic blocks (Fig. 12).

NOTE: Adjust the canopy screws as

Warning:

These plastic blocks are used to avoid

collision damage between motorized main

engine shell during transportation. Please

discard the plastic blocks prior to installation.

necessary until the canopy and canopy

cover are snug.

10

Hanger

Bracket

Hanger

Bracket Screw

Canopy

Screw

Key

Hole Slot

Canopy

Cover

12

11

Fig. 10

Fig. 12

Fig. 11-1 Fig. 11-2

Fig. 11-3

Blade Bracket

Screw

Plastic Block

Blade

fiber washer

blade screws

Blade

Blade Bracket

18

05

Attach two blade bracket screws to the

blade brackets by using the screw retainer

to keep the screws in place. Repeat for all

remaining blades (Fig.13).

13 Fig. 13

Blade

Assembly

Blade Bracket

Screw

14

Remove 3 light kit screws from the fan

motor assembly. Attach the light plate to

the fan motor assembly. Secure by

tightening the 3 screws (Fig. 14).

15 Fig. 15

18 W LED

Assembly

Light Plate

Connection

Plugs

While holding the LED assembly under your fan, firmly snap the wire connection plugs together.

Align the two arrow marks on the light plate and the LED assembly, then turn the LED assembly

clockwise until it stops to ensure tight fit (Fig. 15).

Fig. 14

Round

Hole light kit screws

Light Plate

Motor

Assembly

Attach the fan blade assembly to the fan

motor assembly by aligning the blade

bracket screws with the screw holes in the

motor assembly. Tighten screws securely

(Fig. 13), Repeat for all remaining blades.

Screw Retainers (This will

help keeping the screws

in place for ease of assembly)

19

06

OPERATION

Step 1: Turn off the AC power to all fans to begin the learning process

on any single fan.

Step 2: Restore power to only one fan at a time for

pairing; the rest remain off by use of your wall-mounted

power switch.

Step 3: After the AC power is on, do not press any other button on the

remote control before pressing the (FAN ON/OFF) button. Doing so

will cause the procedure to fail. Within 30 seconds of turning the fan’s

AC power ON, press and hold the button for 5 seconds to enter the

learning function.

Once the receiver has detected the set frequency, the light will blink

two times when the pairing is complete.

Step 4: Repeat steps 1, 2, and 3 with each fan to ensure each fan can

be operated by the paired remote only, and without interfering with

each other.

Remote Control Operation Instructions

WARNING: Do not short-circuit, disassemble, heat up,

connect improperly, or dispose of used batteries in ﬁre.

Do not recharge or mix batteries with used or other batt-

ery types. Immediately remove used batteries.

WARNING:

a) The batteries shall be disposed of properly, including

keeping them away from children; and

b) Even used batteries may cause injury.

Install a 12 V battery into the remote control. Fasten the battery

cover screw after installation. To prevent damage to the remote

control, remove the battery if not used for long periods of time.

Learning Process

NOTE: Should you desire to install more than one fan in your

home, please install one by one by following the steps

below to ensure each fan can be operated individually:

01

20

06

NOTE: On start-up your ceiling fan will oscillate back and forth. This is

NORMAL OPERATION for DC ceiling fan as it goes through its calibration

cycle. The fan is NOT DEFECTIVE.

•

Attach the remote control holder with the two

remote control holder mounting screws.

1. Fan button. Press and release the button to turn the fan on or off.

Fan on/off. The fan memory function will store the current setting for the next

time the fan is in use.

2. 1,2,3,4,5,6 buttons:

These six buttons are used to set the fan speed as follows:

1=low speed 2=medium low speed

3=medium speed 4=medium high speed

5=high speed 6=extra high speed

3. Light functions

Press and release button one time to turn the light on or off.

Press to increase the desired light level.

Press to decrease the desired light level.

4. Fan reverse button (Must be pushed when the fan is in operation.)

(Counter-clockwise direction) A downward air ﬂow creates a cooling effect.

This allows you to set your air conditioner on a higher setting without affecting

your comfort.

(Clockwise direction) An upward air ﬂow moves warm air off the ceiling. This

allows you to set your heating unit on a lower setting without affecting your

comfort.

Installing The Remote Control Holder

02

• Press and release button to select the desired colour

temperature.

La page charge ...

NOMA Ashton 5-Blade 3-Speed Le manuel du propriétaire

NOMA Ashton 5-Blade 3-Speed Le manuel du propriétaire

Documents connexes

Autres documents