NOMA Harper 4-Blade 6-Speed Outdoor Le manuel du propriétaire

HARPER 52” LED CEILING FAN

PRODUCT NO. 052-9720-8

USER MANUAL

READ AND SAVE THESE INSTRUCTIONS

TABLE OF CONTENTS

3

01. SAFETY/CAUTIONS

02. TOOLS REQUIRED

03. EXPLODED VIEW

04. ELECTRICAL SAFETY

05. ASSEMBLY

06. OPERATION

07. TROUBLESHOOTING

08. DYNAMIC BLADE BALANCING KIT

09. MAINTENANCE

10. WARRANTY & DISPOSAL

4

6

7

11

13

19

21

23

25

26

11. IC STATEMENT 27

4

SAFETY / CAUTIONS

•

TO REDUCE THE RISK OF ELECTRIC SHOCK, ENSURE ELECTRICITY HAS

BEEN TURNED OFF AT THE CIRCUIT BREAKER OR FUSE BOX BEFORE

BEGINNING.

ELECTRICAL CODES. ELECTRICAL INSTALLATION SHOULD BE PERFORMED

BY A QUALIFIED LICENSED ELECTRICIAN.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO

NOT USE THIS FAN WITH ANY SOLID-STATE FAN-SPEED CONTROL

DEVICE. IT WILL PERMANENTLY DAMAGE THE ELECTRONIC CIRCUITRY.

CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, USE ONLY THE

SCREWS PROVIDED WITH THE OUTLET BOX.

THE OUTLET BOX AND SUPPORT STRUCTURE MUST BE SECURELY

MOUNTED AND CAPABLE OF RELIABLY SUPPORTING A MINIMUM OF

SUPPORT.”

AVOID PLACING OBJECTS IN THE PATH OF THE BLADES.

TO AVOID PERSONAL INJURY OR DAMAGE TO THE FAN AND OTHER

ITEMS BE CAUTIOUS WHEN WORKING AROUND OR CLEANING THE

FAN.

DO NOT USE WATER OR DETERGENTS WHEN CLEANING THE FAN

OR FAN BLADES. A DRY DUST CLOTH WILL BE SUITABLE FOR MOST

CLEANING.

AFTER MAKING ELECTRICAL CONNECTIONS, SPLICED CONDUCTORS

SHOULD BE TURNED UPWARD AND PUSHED CAREFULLY UP INTO

THE OUTLET BOX. THE WIRES SHOULD BE SPREAD APART WITH THE

GROUNDED CONDUCTOR AND THE EQUIPMENT-GROUNDING

CONDUCTOR ON ONE SIDE OF THE OUTLET BOX AND THE

UNGROUNDED CONDUCTOR ON THE OTHER SIDE OF THE OUTLET BOX.

ALL SET SCREWS MUST BE CHECKED AND RE-TIGHTENED WHERE

NECESSARY BEFORE INSTALLATION.

THE TRAILING EDGE OF THE BLADES TO THE FLOOR.

ALL WIRING MUST BE IN ACCORDANCE WITH NATIONAL AND LOCAL

35 LB (15.9 KG). USE ONLY UL-LISTED OUTLET BOXES MARKED “FOR FAN

THE FAN MUST BE MOUNTED WITH A MINIMUM OF 6’11’’(2.1M) FROM

5

01

•

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT” WITH THE SCREWS PROVIDED WITH

THE OUTLET BOX.

WARNING: TO AVOID RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES) OR THE BRACKETS

WHILE BALANCING THE BLADES OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT” OF 35 LB (15.9 KG) OR LESS”

AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX.

MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF

LIGHT FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY

NEED TO BE REPLACED. DUE TO THE COMPLEXITY OF THIS FAN, A

QUALIFIED LICENSED ELECTRICIAN IS STRONGLY RECOMMENDED FOR

INSTALLATION.

6

01 02

TOOLS REQUIRED

INSTALLATION PREPARATION

Flat-head

screwdriver

Cross-head

screwdriver

Safety glasses Pliers

Wire cutters Electrical tape Stepladder Wire strippers

6' 11"

(2.1 m)

30”

(76 cm )

To prevent personal injury and

damage, ensure that the hanging

location allows the blades a

clearance of 6' 11" (2.1 m) from the

floor and 30" (76 cm) from any wall or

obstruction.

This fan can be mounted with a

downrod on a regular (no-slope) or

vaulted ceiling, such as flush mount.

Flush Mount

Installation

Downrod

Installation

Vaulted

ceiling angle

is not to

exceed 18°

Blade Edge

7

03

EXPLODED VIEW

PACKAGE CONTENTS

07

03

06 08

Installation

Instruction

X 3

X 2

X 3

X 2

X 1 X 3

8

03 EXPLODED VIEW

PACKAGE CONTENTS

01.

02.

03.

04.

05.

06.

07.

08.

09.

10.HANGER BRACKET

CANOPY

CANOPY COVER

DOWNROD STAND COVER

DOWNROD, HANGER PIN

& LOCK PIN

FAN MOTOR ASSEMBLY

FAN BLADES (4 PCS)

LIGHT PLATE

18 W LED ASSEMBLY

11.

12.

13.

14.

15.

16.

REMOTE CONTROL HOLDER

12 V BATTERY

BLADE BALANCING KIT

INSTALLATION INSTRUCTIONS

REMOTE CONTROL

RECEIVER

PARTS PACK CONTAINING:

3 x Wood Screws

2 x Machine Screws

3 x Flat Washers

3 x Spring Washers

2 x Star Washers

3 x Wire Nuts

1 x Blade Screw

17. EXTENSION POWER CORD

(42˝ / 106.7 CM)

9

03

EXPLODED VIEW

DETAIL

01.

02.

03.

04.

05.

06.

07.

08.

09.

10.

HANGER PIN

CANOPY

HANGER BALL

HANGER BRACKET

LIGHT PLATE

COLLAR

FAN BLADE

LOCK PIN

FAN MOTOR ASSEMBLY

11.

12.

13.

DOWNROD STAND COVER

DOWNROD

CANOPY COVER

18 W LED ASSEMBLY

10

03

12

13

11

01

09

10

02

03

04

07

05

06

08

11

04

ELECTRICAL SAFETY

Instructions

•

01.

02.

03.

04.

Making the Electrical Connections

•

Read all safety information and installation instructions before

you begin to install the fan and save instructions.

All set screws of the fan must be checked and re-tightened

where necessary before installation.

To reduce the risk of personal injury, do not bend the blade

brackets when installing the brackets, balancing the blades

or cleaning the fan. Do not insert foreign objects between

rotating fan blades.

Before changing the fan direction, turn off the fan and wait for

the fan blades to stop completely.

The safeguards provided by these safety instructions and by

the separate installation instructions are not meant to cover all

possible conditions and situations that may occur. It must be

understood that common sense, caution and care are factors

which cannot be built into this product. These factors must be

supplied by the person(s) installing, caring for and operating

the fan.

WARNING: To avoid risk of electric shock, be sure to shut off

power at the main fuse or circuit breaker box before installing

To reduce the risk of injury, install the fan so that the blades are

at least 6’ 11’’ (2.1M) above the floor and at least 30’’ (76cm)

from the tip of the blades to the wall.

12

04

•

mount the outlet box marked “ACCEPTABLE FOR FAN

SUPPORT” and use mounting screws provided with the outlet

box.

The installation must be in accordance with the national

electrical code, ANSI/NFPA 70-1999 and local codes. If you

are unfamiliar with the methods of installing electrical wiring,

injury, mount to outlet box and use mounting screws provided

with the outlet box.

IMPORTANT: Before you begin installing the fan, carefully read

all information on the separate sheet “SAFETY INSTRUCTIONS”

NOTE: The fan weight is 13 lb (5.9kg). Be sure the outlet box you

are using is securely attached to the building structure and can

support the full weight of the fan. Failing to do so can result in

serious injury.

as well as the following “Installation Instructions Steps”. If in doubt,

consult a qualified electrician.

13

05

01 02

ASSEMBLY

INSTRUCTIONS

Fig. 1

Fig. 2

Outlet

Box

Outlet Box

Screw

04

Turn OFF the electric circuit at the main

fuse of circuit breaker box (Fig. 1).

Fig. 4

Hanger

Downrod

Lock

03 Fig. 3

Lock

Hanger

Downrod

Cross Pin

Hanger Ball

Securely attach the hanger bracket to

an outlet box marked "ACCEPTABLE FOR

FAN SUPPORT" using the supplied outlet

box screws with spring washers (Fig. 2).

Hanger

Bracket

Warning: Ensure wiring is not pinched or

twisted.

Thread the motor wires safety cable through

the downrod and downrod stand. Insert the

downrod into the collar. Slide hanger pin

through holes of collar and downrod (Fig. 4).

Remove the lock pin and take out the hanger

pin; then remove the hanger ball from the

downrod assembly by loosening the set

screw and removing the cross pin (Fig. 3).

14

05

Cross Pin

Set Screw

Fig. 8Fig. 7

07 08

Hanger

Bracket

Slot Clip

Insert and tighten the two collar screws.

Slide lock pin into hanger pin until it is

locked into position (Fig. 5).

05 06

Fig. 5

Hanger Ball

Fig. 6

Lock Pin

Downrod

Canopy

Canopy Cover

Hanger

Downrod

Stand Cover

Motor Wires

Hanger Ball

Safety Cable

Lock Pin

Collar Screws

Hanger

Hang the fan onto the hanger bracket,

and make sure the slot of the hanger ball

is aligned with the clip of the hanger

bracket (Fig. 8).

Carefully reinstall the hanger ball onto rod,

being sure that cross pin is in correct position,

set screws are tightened and wires are not

twisted (Fig. 7).

Slide downrod cover, canopy cover and

canopy over the downrod as shown (Fig. 6).

15

05

Fig. 9

ASSEMBLY

09

The safety cable prevents the fan from falling. Secure the safety cable to the ceiling joist with

a wood screw, star washer and flat washer (Fig. 9).

Safety

Cable

Star Washer

Wood

Screw

Flat Washer

IMPORTANT: If you are not sure if the electrical outlet box and fan are

grounded, contact a licensed electrician for advice. They must be

grounded for safe operation.

WARNING: To avoid possible electric shock, be sure electricity is turned

off at the main fuse box before wiring.

Wiring Instructions

•

Leave unconnected and do not cut.

VIEW AFTER INSTALLATION

Insert receiver into hanger bracket with the flat side of the receiver

facing the ceiling.

Connect the male connectors from the fan to the female connectors

from the receiver.

Between Fan & Receiver & Mains

•

Once the connection has been made, the receiver inserts into the

down rod hanger bracket. The canopy comes up to cover the receiver

and bracket.

16

05

Receiver to House Supply Wires Electrical Connections: Connect the

WHITE wire (Neutral) from the outlet box to the WHITE wire marked “AC

in N” from the receiver. Connect the BLACK wire (Hot) from the outlet

box to the BLACK wire marked “AC in L” from the receiver. Secure all

wire connections with the plastic wire nuts provided.

•

RECEIVER

BLUE

WHITE

GREY

RED

YELLOW

YELLOW & GREEN

OUTLET BOX

HOT

AC IN N

AC IN L

YELLOW & GREEN

RECEIVER

BLUE

WHITE

GREY

RED

YELLOW

YELLOW & GREEN

OUTLET BOX

YELLOW & GREEN

GROUND

AC IN N

AC IN L

HOT

GROUND

NEUTRAL

WIRE NUT

HANGER

BRACKET

NOTE: Fan must be installed at a maximum distance of 40’ (12.2 m) from

the transmitting unit for proper signal transmission between the transmitting

unit and the fan’s receiving unit.

Connect the ground wire (yellow & green or bare copper) from the

outlet box to the ground wire of hanging ball and the ground wire of

hanger bracket and the receiver ground wire. Secure wire connection

with the plastic wire nut provided.

17

05

ASSEMBLY

11 Fig. 11

Blade

Blade Screw

Remove twelve blades screws from the fan motor assembly. Attach the fan blades to the fan

motor assembly one by one by aligning the blade screws with the screw holes in the motor

assembly. Tighten screws securely (Fig. 11).

10

Hanger

Bracket

Hanger

Bracket Screw

Canopy

Screw

Key

Hole Slot

Canopy

Cover

Fig. 10

Note: Ensure that the blade side indicated "This side up" is facing the ceiling for correct blade

installation.

NOTE: Adjust the canopy screws as necessary until the canopy and canopy cover are snug.

Push up the canopy cover until the screw heads engage to the slots on the canopy cover

and rotate the canopy cover until it is attached to the bottom of the canopy securely (Fig. 10).

Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other one

half a turn from the screw head. Slide the canopy up towards the hanger bracket and place

the key hole on the canopy over the screw on the hanger bracket, then turn canopy until it

locks in place at the narrow section of the key holes. Align the circular hole on the canopy

with the remaining hole on the hanger bracket, secure with previously removed hanger

bracket screw, and tighten both hanger bracket screws securely (Fig. 10).

18

05

12

Remove 3 light kit screws from the fan motor assembly. Attach the light plate to the fan motor

assembly. Secure by tightening the 3 screws

(Fig. 12).

13

Fig. 12

Fig. 13

Light Plate

Round Hole

Light Kit Screws

Motor

Assembly

18 W LED

Assembly

Light Plate Connection

Plugs

While holding the LED assembly under your fan, firmly snap the wire connection plugs together.

Align the two arrow marks on the light plate and the LED assembly, then turn the LED assembly

clockwise until it stops to ensure tight fit (Fig. 13).

19

06

OPERATION

Step 1: Turn off the AC power to all fans to begin the learning process

on any single fan.

Step 2: Restore power to only one fan at a time for

power switch.

Step 3: After the AC power is on, do not press any other button on the

remote control before pressing the (FAN ON/OFF) button. Doing so

will cause the procedure to fail. Within 30 seconds of turning the fan’s

AC power ON, press and hold the button for 5 seconds to enter the

learning function.

Once the receiver has detected the set frequency, the light will blink

two times when the pairing is complete.

Step 4: Repeat steps 1, 2, and 3 with each fan to ensure each fan can

be operated by the paired remote only, and without interfering with

each other.

Learning Process

NOTE: Should you desire to install more than one fan in your

below to ensure each fan can be operated individually:

01

Remote Control Operation Instructions

WARNING: Do not short-circuit, disassemble, heat up,

connect improperly, or dispose of used batteries in ﬁre.

Do not recharge or mix batteries with used or other batt-

ery types. Immediately remove used batteries.

Install a 12 V battery into the remote control. Fasten the battery

cover screw after installation. To prevent damage to the remote

control, remove the battery if not used for long periods of time.

WARNING:

a) The batteries shall be disposed of properly, including

keeping them away from children; and

b) Even used batteries may cause injury.

pairing; the rest remain off by use of your wall-mounted

home, please install one by one by following the steps

20

06

•

Fan on/off. The fan memory function will store the current setting for the next

time the fan is in use.

2. 1,2,3,4,5,6 buttons:

These six buttons are used to set the fan speed as follows:

1=low speed 2=medium low speed

3=medium speed 4=medium high speed

3. Light functions

Press to increase the desired light level.

Press to decrease the desired light level.

4. Fan reverse button (Must be pushed when the fan is in operation.)

This allows you to set your air conditioner on a higher setting without affecting

your comfort.

(Clockwise direction) An upward air ﬂow moves warm air off the ceiling. This

allows you to set your heating unit on a lower setting without affecting your

comfort.

Installing The Remote Control Holder

02

• temperature.

NOTE: On start-up your ceiling fan will oscillate back and forth. This is

NORMAL OPERATION for DC ceiling fan as it goes through its

calibration cycle. The fan is NOT DEFECTIVE.

1. Fan button. Press and release the button to turn the fan on or off.

5=high speed 6=extra high speed

Press and release button one time to turn the light on or off.

Press and release button to select the desired colour

(Counter-clockwise direction) A downward air ﬂow creates a cooling effect.

Attach the remote control holder with the two

remote control holder mounting screws.

La page charge ...

NOMA Harper 4-Blade 6-Speed Outdoor Le manuel du propriétaire

NOMA Harper 4-Blade 6-Speed Outdoor Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents